panel convector heaters - Electric Radiators Direct

panel convector heaters - Electric Radiators Direct
PANEL CONVECTOR HEATERS
INSTALLATION INSTRUCTIONS AND USER GUIDE
PHM075
PHM125
PHM150
PHM200
RATING 750 W
RATING 1250 W
RATING 1500 W
RATING 2000 W
Before connecting the unit for the first time, please, read
these instructions carefully.
2. - Installation instructions
- When positioning the heater for installation it is important that a minimum clearance of 50 cm must be allowed between the heater and any
combustible materials, such as furniture, curtains etc, to ensure the best
heating results.
1. - IMPORTANT INFORMATION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fig. 1
- Open the carton at the indicated side. The screws are in the accessories
bag. Turn the carton upside down to allow the heater to stand. Check that
it is the correct model and that it is in good condition.
- Fix the two square brackets to the back of the heater by using the two
small screws (see Fig. 1).
4
5
6
7
1
6
3
8
.
.
.
.
0
0
5
5
c
c
c
c
m
m
m
m
(
(
(
(
1
1
2
7
2
5
0
5
5
0
0
0
0
0
0
W
W
W
W
)
)
)
)
41.0 cm
•
min 20cm
•
•
The warranty of the panel heater will not cover any damage
caused by non observance of any of these instructions.
This Guide must be kept and given to any new owner.
Before connecting this appliance to any power supply, the wall
fixing bracket located below has to be detached.
Check that the voltage shown on the rating plate on the heater is
the same as the voltage of the supply to which connection is to be
made.
Should the heater be moved and reinstalled it is essential that the
work is carried out by a competent electrician.
The use of panel heaters is forbidden in any area where there is a
presence of gases, explosives or inflammable objects.
Do not use this heater to dry clothes.
Neither the connecting cable nor any other object must come into
contact with the hot unit.
Do not cover this heater at any time.
The surfaces of this heater can be hot, so young children should
not be left unsupervised in the vicinity of the heater.
The air outlet grill at the top of the heater cabinet and the air inlet
at the bottom of the heater are provided to ensure the most efficient operation of the appliance. They also protect the heater from
overheating; therefore, it is essential that at no time are they covered.
This heater should be disconnected from the electricity supply
before any repair work is carried out. This action should also be
taken during the times of the year when heat is not required.
The panel heater should not be installed just below an electrical
socket.
The appliance must be installed in such a way that switches and
other control devices cannot be touched by a person using a bath
or shower.
The installation must be carried out in accordance with the current
electrical regulations.
The heater is fitted with a flexible cable size 3 x 1.00 mm2 for
electrical connection. It may be used to connect the heater to the
fixed wiring of the premised through a suitable connection box positioned adjacent to the panel heater.
This appliance must be connected to the supply by fixed wiring.
The supply circuit to the heater must incorporate a double pole
isolating switch having a contact separation of at least 3 mm.
If the flexible power cable for this unit is damaged, it may only be
replaced by a repair workshop recognised by the manufacturer, as
special tools are necessary.
This appliance must be earthed.
Before carrying out any work inside the appliance, the panel heater
must be disconnected from the electricity supply.
The presence in the air of particles of smoke, dust and other
pollutants could, in time, discolour the walls and surfaces around
the panel heater.
Please complete the enclosed warranty card and return it to the
manufacturer to enable registration to take place.
All models are supplied with an electrical interrupt cut-out. This will
switch off the heater if, for any reason, it overheats. Should the
cut-out operate, turn the heater off and remove the cause for the
overheating. The cut-out will be reset automatically.
min 20cm
•
230 – 240 V~
230 – 240 V~
230 – 240 V~
230 – 240 V~
8
c
1
m
0
c
m
m
i n
1
5
c
m
m
i n
1
5
c
m
Fig. 2
- Position and fix the top bracket at the correct distance from the floor
(see Fig. 2) and hang the unit on the hooks of the top bracket. Mark the
fixing points on the wall using a pencil. Use the heater fixing holes as a
template and mark the wall through the two fixing holes in the square
brackets. Fix the heater to the wall.
3. - Using the panel heater.
Switch on the heater by setting the switch marked I-O to “ I “. The off position is marked
“O“.
When the heater is generating heat the neon indicator on the switch will be illuminated.
The heater is fitted with an adjustable thermostat, which enables room temperature to be
controlled by adjusting the setting accordingly. Turn the thermostat control to the maximum
(fully clockwise) to heat the room rapidly. When the desired temperature has been reached,
turn the thermostat control slowly to the left (anti-clockwise) until the luminous indicator
switches off. By leaving in this position, the heater will automatically maintain the selected
temperature.
3. - Cleaning and maintenance.
Clean and dust with a dry, soft cloth only when the unit is disconnected and cold.
Do not use solvents or abrasive products for cleaning.
4. - Wiring
1A
1
R: Heating Element with Safety Cut Out
C: Switch
Ta: Ambient Thermostat
1B
C
R
T
Brown:
GB:
Live
Blue:
Neutral
Green and Yellow:
Earth
WARNING: In order to avoid overheating do not cover the heater.
The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where
you purchased the product. These instructions are only valid in the EU member states.
Made by ELNUR s.a.
Pol. Ind. “El Nogal” c/ Villa Esther, 11
28110 Algete (Madrid)
www.elnur.es
As a part of the policy of continuous product improvement Elnur s.a reserves the right to alter specifications without notice.
@ 2012
Cod. 40490017-B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement