user manual

user manual
USER MANUAL
PRT80III
CUSTOM S.p.A.
Via Berettine 2/B
43010 Fontevivo (PARMA) - Italy
Tel. : +39 0521-680111
Fax : +39 0521-610701
http: www.custom.biz
Customer Service Department:
Email : [email protected]
© 2015 CUSTOM S.p.A. – Italy.
All rights reserved. Total or partial reproduction of this manual in whatever form,
whether by printed or electronic means,
is forbidden. While guaranteeing that the
information contained in it has been carefully checked, CUSTOM S.p.A. and other
entities utilized in the realization of this
manual bear no responsibility for how the
manual is used.
Information regarding any errors found in it
or suggestions on how it could be improved
are appreciated. Since products are subject to continuous check and improvement,
CUSTOM S.p.A. reserves the right to make
changes in information contained in this
manual without prior notii cation.
The pre-installed multimedia contents
are protected from Copyright CUSTOM
S.p.A. Other company and product names
mentioned herein may be trademarks of
their respective companies. Mention of
third-party products is for informational
purposes only and constitutes neither
an endorsement nor a recommendation.
CUSTOM S.p.A. assumes no responsibility
with regard to the performance or use of
these products.
THE IMAGES USED IN THIS MANUAL ARE USED AS AN ILLUSTRATIVE EXAMPLES. THEY COULDN’T
GENERAL SAFETY INFORMATION
Your attention is drawn to the following
actions that could compromise the characteristics of the product:
• Read and retain the instructions which
follow.
• Follow all indications and instructions
given on the device.
• Make sure that the surface on which
the device rests is stable. If it is not, the
device could fall, seriously damaging it.
• Make sure that the device rests on a hard
(non-padded) surface and that there is
sufi cient ventilation.
• When positioning the device, make sure
cables do not get damaged.
• Use the type of electrical power supply
indicated on the device label. If uncertain, contact your dealer.
• Make sure the electrical system that
supplies power to the device is equipped
with a ground wire and is protected by a
differential switch.
• Do not block the ventilation openings.
• Do not insert objects inside the device as
this could cause short-circuiting or damage components that could jeopardize
printer functioning.
• Do not carry out repairs on the device
yourself, except for the normal maintenance operations given in the user
manual.
• Make sure that there is an easily-accessible outlet with a capacity of no less
than 10A closely to where the device is
to be installed.
• Periodically perform scheduled maintenance on the device to avoid dirt build-up
that could compromise the correct, safe
operation of the unit.
• Before any type of work is done on the
machine, disconnect the power supply.
• Do not touch the head heating line with
bare hands or metal objects. Do not
perform any operation inside the printer
immediately after printing because the
head and motor tend to become very
hot.
REPRODUCE THE DESCRIBED
MODEL FAITHFULLY.
UNLESS OTHERWISE SPECIFIED,
THE INFORMATION GIVEN IN THIS
MANUAL
ARE REFERRED TO ALL MODELS
IN PRODUCTION AT THE ISSUE
DATE OF THIS DOCUMENT.
GENERAL INSTRUCTIONS
CUSTOM S.p.A. declines all responsibility for accidents or damage to persons or
property occurring as a result of tampering,
structural or functional modii cations, unsuitable or incorrect installations, environments not in keeping with the equipment’s
protection degree or with the required temperature and humidity conditions, failure
to carry out maintenance and periodical
inspections and poor repair work.
THE CE MARK AFFIXED TO
THE PRODUCT CERTIFY
THAT THE PRODUCT SATISFIES THE BASIC SAFETY
REQUIREMENTS.
The device is in conformity with the essential Electromagnetic Compatibility and
Electric Safety requirements laid down in
Directives 2006/95/CE and 2004/108/CE
inasmuch as it was designed in conformity
with the provisions laid down in the following Standards:
• EN 55022 Class B (Limits and methods
of measurements of radio disturbance
characteristics of Information Technology Equipment)
• EN 55024 (Information Technology
Equipment – Immunity characteristics –
Limits and methods of measurement)
• EN 60950-1 (Safety of information
equipment including electrical business
equipment)
GUIDELINES FOR
THE DISPOSAL OF
THE PRODUCT
The crossed-out rubbish bin logo means
that used electrical and electronic products
shall NOT be mixed with unsorted municipal waste. For more detailed information
about recycling of this product, refer to the
instructions of your country for the disposal
of these products.
• Do not dispose of this equipment as
miscellaneous solid municipal waste, but
arrange to have it collected separately.
• The re-use or correct recycling of the
electronic and electrical equipment
(EEE) is important in order to protect
the environment and the wellbeing of
humans.
• In accordance with European Directive
WEEE 2002/96/EC, special collection
points are available to which to deliver
waste electrical and electronic equipment and the equipment can also be
handed over to a distributor at the moment of purchasing a new equivalent
type.
• The public administration and producers
of electrical and electronic equipment
are involved in facilitating the processes
of the re-use and recovery of waste electrical and electronic equipment through
the organisation of collection activities
and the use of appropriate planning arrangements.
• Unauthorised disposal of waste electrical
and electronic equipment is punishable
by law with the appropriate penalties.
The format used for this manual improves use of natural resources reducing the quantity of necessary paper to print this
copy.
MANUAL
For details on the commands,
refer to the manual with code 77200000003100
TABLE OF CONTENTS
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
1.1 Document structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2 Explanatory notes used in this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
2.1 2.2 2.3 2.4 2.5 2.6 Box content. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device components: external views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key functions: power up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key functions: standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED flashes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
13
15
16
17
18
3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
3.1 Fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 Driver and SDK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
22
23
26
4 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
4.1 Switch the device ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.2 Loading the paper roll. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.3 Fixing the paper on rewinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5 CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
5.1 5.2 5.3 5.4 5.5 Configuration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hexadecimal dump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
34
35
36
40
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
6.1 Printer paper jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Planning of cleaning operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4 Upgrade firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
43
44
48
7
8
7 SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
7.1 7.2 7.3 7.4 7.5 Hardware specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of power supply cod. 963GE020000003 (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
54
55
56
57
8 CONSUMABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
9 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
10 TECHNICAL SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
11 ADVANCED FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
11.1 File sharing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 Drivers installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3 Logos management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4 Fonts management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
65
66
66
67
1
INTRODUCTION
1.1
Document structure
This document includes the following chapters:
1
INTRODUCTION
information about this document
2
DESCRIPTION
general description of device
3
INSTALLATION
information required for a correct installation of the device
4
OPERATION
information required to make the device operative
5 CONFIGURATION description of the coniguration parameters of the device
6
information for a correct periodic maintenance
MAINTENANCE
7 SPECIFICATION technical speciication for the device and its accessories
8
CONSUMABLES
description and installation of the available consumables for the device
9
ACCESSORIES
description and installation of the available accessories for the device
10 TECHNICAL SERVICE
information required for contacting the technical service
11 ADVANCED FUNCTIONS
information about special functions available with the device
1.2
Explanatory notes used in this manual
NOTE:
Gives important information or suggestions relative to the use of the device
ATTENTION:
Gives information that must be carefully followed to guard against damaging the
device
DANGER:
Gives information that must be carefully followed to guard against operator injury or
damage
9
10
2
DESCRIPTION
2.1
Box content
Remove the device from its carton being careful not to damage the packing material so that it may be re-used if the device
is to be transported in the future.
Make sure that all the components illustrated below are present and that there are no signs of damage. If there are, contact
Customer Service.
PRT80III (standard models)
1. Installation instruction sheet
2. Device
1
2
11
PRT80III (models with encoder)
3. Installation instruction sheet
4. Device
1
2
• Open the device packaging.
• Take out the device.
• Take out the rest of the content.
• Keep the box, trays and packing materials in the event the device must be transported/shipped in the future.
12
2.2
Device components: external views
PRT80III (standard models)
1. Rewinder
12. External ring for roll blocking (adjustable)
2. Device chassis
13. Connector for near paper end sensor
3. Near paper end LED
14. Power supply port
4. STATUS LED
15. USB port
5. POWER ON LED
16. RS232 serial port
6. FF FORM FEED key
17. Paper input
7. LF LINE FEED key
18. Near paper end sensor
8. Printing mechanism motor
19. Printing mechanism + head temperature sensor
9. Lifting lever for printing head
20. Sensor for paper presence in input
10. Sensor for printing head lifted
21. Paper out
11. Roll holder support
22. Roll holder pin 80mm
22
21
20
1
19
18
17
2
3
4
5
6
7
8
9
10
11
16
12
15
14
13
13
PRT80III (models with encoder)
1. Rewinder
13. External ring for roll blocking (adjustable)
2. Device chassis
14. Connector for near paper end sensor
3. Near paper end LED
15. Power supply port
4. STATUS LED
16. USB port
5. POWER ON LED
17. RS232 serial port
6. FF FORM FEED key
18. Anti-jam sensor
7. LF LINE FEED key
19. Paper input
8. Sensor bracket anti-jam
20. Near paper end sensor
9. Printing mechanism motor
21. Printing mechanism + head temperature sensor
10. Lifting lever for printing head
22. Sensor for paper presence in input
11. Sensor for printing head lifted
23. Paper out
12. Roll holder support
24. Roll holder pin 80mm
24
23
22
1
21
20
19
2
18
3
4
5
6
7
8
9
10
11
12
17
13
16
15
14
14
2.3
Product label
PC = Product code (14 digits)
SN = Serial number
HW = Hardware release
XXXXXXXXXXXXXX
Rx
0000000000000000000
PC
SN
HW
15
2.4
Key functions: power up
POWER UP
FF
LF
FF
LF
Hold
down
Hold
down
printing
FONT TEST
printing
SETUP report
FF
LF
FF
Fast
push
Fast
push
skip the
SETUP mode
enter the SETUP MODE
FF
LF
Fast
push
modify
parameter
16
LF
FF
LF
Fast
push
next
parameter
2.5
Key functions: standby
STANDBY
FF
LF
Fast
push
Printing
logo
FF
LF
Fast
push
Advance the paper
(preset length)
17
2.6
LED lashes
The three status LED indicates hardware status of device.
POWER ON LED
Signals the status of the powered device as shown in the following table.
STATUS LED
DESCRIPTION
-
OFF
DEVICE NOT POWERED
GREEN
ON
DEVICE POWERED
NEAR PAPER END LED
Signals the amount of paper on the paper roll as shown in the following table.
STATUS LED
18
DESCRIPTION
-
OFF
PAPER IN ABUNDANCE
RED
ON
NEAR PAPER END
STATUS LED
The Status LED indicates hardware status of device. Given in the table below are the various LED signals and the corresponding device status.
STATUS LED
DESCRIPTION
-
OFF
DEVICE OFF
YELLOW
ON
DEVICE ON: NO ERROR
x1
RECEIVE DATA
x2
HEADING OVER TEMPERATURE
x3
PAPER END
x4
POWER SUPPLY VOLTAGE INCORRECT
x5
COM PORT ERROR
x6
COMMAND NOT RECOGNIZED
x7
CHARACTER RECEPTION ERROR
x8
PRINTING HEAD LIFTED
x9
PAPER JAM
x 10
CUTTER ERROR
x 11
RAM ERROR
x 12
EXTERNAL MEMORY ERROR
YELLOW
19
20
3
INSTALLATION
3.1
Fastening
NOTE: All the dimensions shown in following igures are in millimetres.
102
13
The device is provided with three ixing holes on the bottom of device (see following igure).
To install the device on a panel, use four M3 screws.
13
M3
15
143
21
3.2
Connections
The following igure shows the possible connections for the device.
Power supply cable
(see following
paragraphs)
Power supply
USB
standard cable
PC
USB device
Serial
standard cable
PC
serial device
ATTENTION: In some using conditions, we recommend the installation of a ferrite core on the power supply cable.
NOTES: If serial and USB connectors are inserted, communication port is USB.
22
3.3
Pinout
2
1
3
POWER SUPPLY
Tripolar female connector
4
1 GND
2 +24 V
J19
3 GND
4 Frame GND
ATTENTION:
Respect power supply polarity.
NOTE:
Power supply cable
The following igure shows the connector pinout of the power supply cable for the device:
Tripolar male connector
n.c.
+24 V
GND
Power supply cable
2
1
USB INTERFACE
Female USB type B connector
3
4
1 USB0-VBUS
J12
(in)
2 USB0_D-
(in/out)
3 USB0_D+
(in/out)
4 GND
SH1 SHIELD
SH2 SHIELD
23
5
9
1
6
RS232 SERIAL INTERFACE
Female DB9 connector
1 DTR
2 TX
During transmission, takes the values “0” and “1” depending on data.
3 RX
During reception, takes the values “0” and “1” depending on data.
4 DSR
J10
5 GND
6 DTR
When “1”, device is power on.
7 CTS
8 RTS
When “1”, device is ready to receive data
9 VCC
NOTES:
Given the presence of the RS232 standard, logic value “0” corresponds to a voltage level of between +3Vdc and +15Vdc
and logic value “1” corresponds to a voltage level of between -3Vdc and -15Vdc.
1
2
3
4
5
6
7
8
9
DEVICE
DTR
DC
TX
RX
RX
TX
DSR
GND
DTR
GND
DTR
DSR
CTS
RTS
RTS
CTS
1
2
3
4
5
6
7
8
9
DB9
DB9
DEVICE > PC connection
The following picture shows an example of connection between the device and a personal computer using a 9 pin
RS232 serial connector:
PC
When use a serial cable, we recommend the installation of a ferrite core on the power supply cable.
24
NEAR PAPER END
4
1
4 ways male JST connector (S4B-PH-K-S)
1 VCC
2 QF-EXT
J17
(in)
3 QF-INT
4 GND
NOTE: Cable for near paper end sensor.
The following igure shows the pinout of the connector of the cable for near paper end to use for the device:
Female JST connector
series PHR-4
Cable for near paper end senor
1
PIN
Cable
color
Red
Signal
2
Blue
NPE (input)
3
Black
n.c.
4
Yellow
GND
1
4
+5V
25
3.4
Driver and SDK
The drivers are available for the following operating system:
OPERATING
SYSTEM
DESCRIPTION
INSTALLATION PROCEDURE
Driver for Windows XP
Driver for Windows VISTA (32/64bit)
Windows
Driver for Windows 7 (32/64bit)
From the START menu, press Run
and type-in the path where the SW
was saved on your PC, then click OK.
Follow the instructions that appear
on the screen to install the driver.
Driver for Windows 8 (32/64bit)
Driver for Windows 8.1 (32/64bit)
Android
Library for CustomAndroidAPI
NOTE:
All drivers can be found in the DOWNLOAD section of the web site www.custom.biz.
26
Extract the zipped folder to
the destination path desired.
Follow the instructions present
in the software package that you
downloaded on how to install
and use the library.
4
OPERATION
4.1
Switch the device ON
3
1
Power supply cable
(optional)
EXTERNAL POWER
SUPPLY UNIT
(OPTIONAL)
Connect the power supply cable
to an external power supply unit.
2
The status led (yellow) and the power on led (green)
turn on and the device is ready.
IN DC 24V
2.5A
Power supply
cable
(optional)
Connect the power supply cable to the device.
Use the type of electrical power supply
indicated on the label.
27
4.2
Loading the paper roll
To load the paper proceed as follows. At every change of paper, check inside the device to locate and remove any scraps
of paper.
1
3
Insert the paper roll on the pin
so that it unrolls correctly.
Insert the paper into the input mouth.
4
2
VROOM
Place the paper roll on the
paper roll holder.
28
Wait until the paper is
automatically loaded.
4.3
Fixing the paper on rewinder
1
Load the paper into the device as described in the previous paragraphs.
2
LF
FF
~ 300mm
Press the LF LINE FEED button repeatedly to advance
the paper of at least 300mm beyond the edge of the paper outfeed.
29
3
Pull the paper toward the rewinder respecting the path indicated by the arrows.
4
Remove the rewinder plastic disk and
wrap the paper around the pin as indicated by the arrow.
30
5
Block the paper by inserting the plastic disk.
31
32
5
CONFIGURATION
5.1
Coniguration mode
To enter the coniguration mode and print a SETUP report with the operating parameters of the device, proceed as follows.
1
FF
LF
LF LINE FEED
KEY
2
PRINTER SETUP
While pressing the LF LINE FEED key,
switch on the device by connecting the power supply cable.
The device prints the report with the settings parameters.
Follow the instructions printed on paper to proceed with configuration procedure.
33
5.2
Setup report
The following igure shows the setup report of the device. The shown values for parameters are sample values; for the list and the description of device parameters see the following paragraphs.
PRINTER NAME and
FIRMWARE MODULES
RELEASE
PRT80III
SCODE. <code>
DCODE. <code>
FCODE. <code>
-
rel 1.00
rel 1.00
rel 1.00
PRINTER SETTINGS
DEVICE
STATUS
PRINTER
PARAMETERS
KEYS FUNCTIONS
34
PRINTER TYPE ....................................PRT80III
PRINTING HEAD TYPE ........................SHEC C72
INTERFACE ..........................................USB
PROGRAM MEMORY TEST.................OK
DYNAMIC RAM TEST...........................OK
EXTERNAL MEMORY TEST ................OK
HEAD VOLTAGE
[V] = 24.12
HEAD TEMPERATURE
[°C] = 24
POWER ON COUNTER
= 4
PAPER PRINTED
[cm] = 40
Printer Emulation ............................. :
RS232 Baud Rate ........................... :
RS232 Data Length ......................... :
RS232 Parity ................................... :
RS232 Handshaking ....................... :
Busy Condition ................................ :
USB Mass Storage .......................... :
USB Address Number ..................... :
Print Mode ....................................... :
Autofeed .......................................... :
Chars / inch ..................................... :
Code Table [num] ............................ :
Font Type......................................... :
Speed / Quality................................ :
Paper Threshold .............................. :
USB Virtual COM............................. :
PaperEnd Buffer Clear .................... :
Print Density.................................... :
[ LF ]
[ FF ]
enter Printer Setup
skip Setup
CUSTOM/POS
115200 bps
8 bits/chr
None
Hardware
RxFull
Disabled
0
Normal
CR Disabled
A=15 B=20 cpi
00
International
High Speed
60%
Disabled
Disabled
0%
5.3
Device status
The device operating status is indicated in the coniguration print-out in which, next to the name of the components displayed, the following information is given:
PRINTER TYPE
device model
PRINTING HEAD TYPE
print head model
INTERFACE
interface present
PROGRAM MEMORY TEST
OK appears if functioning and NOT OK if faulty
DYNAMIC RAM TEST
OK appears if functioning and NOT OK if faulty
EXTERNAL MEMORY TEST
OK appears if functioning and NOT OK if faulty
HEAD VOLTAGE
voltage of the head
HEAD TEMPERATURE
temperature of the head
POWER ON COUNTER
number of power-ups made
PAPER PRINTED
centimetres of paper printed
35
5.4
Printer parameters
The device allows the coniguration of the parameters listed in the following table.
The parameters marked with the symbol D are the default values.
Settings remain active even after the device has been turned off and they are stored in non-volatile memory.
PRINTER EMULATION
Available emulations for the device:
CUSTOM/POS D
PRT80
CUSTOM TPT
RS232 BAUD RATE
Communication speed of the serial interface:
1200
2400
4800
9600
19200
38400
57600
115200 D
NOTE: Parameter valid only with serial interface.
RS232 DATA LENGTH
Number of bit used for characters encoding:
8 bits/car D
7 bits/car
NOTE: Parameter valid only with serial interface.
RS232 PARITY
Bit for the parity control of the serial interface:
None D = parity bit omitted
Even = even value for parity bit
Odd =
odd value for parity bit
NOTE: Parameter valid only with serial interface.
RS232 HANDSHAKING
Handshaking:
XON/XOFF =
Hardware D =
software handshaking
hardware handshaking (CTS/RTS)
NOTES:
Parameter valid only with serial interface.
When the receive buffer is full, if handshaking is set to XON/XOFF, the device sends the XOFF (0x13) on the
serial port. When the receive buffer has cleared once again, if handshaking is set to XON/XOFF, the device
sends the XON (0x11) on the serial port.
36
BUSY CONDITION
Activation mode for Busy signal:
RXFull D =
Busy signal is activated when the buffer is full
OffLine/ RXFull = Busy signal is activated when the device is both in OffLine status and
the buffer is full
NOTE: Parameter valid only with serial interface.
USB MASS STORAGE
Sharing mode from Mass Storage:
Disabled D = sharing mode disabled
Enabled =
sharing mode enabled
USB ADDRESS NUMBER
Numerical address code for the univocal identiication of the USB device (in case of more
than a USB device connected with the same PC):
0D
1
PRINT MODE
2
3
4
5
6
7
8
9
Printing mode:
Normal D = enables printing in normal writing way
Reverse = enables printing rotated 180 degrees
AUTOFEED
Setting of the Carriage Return character:
CR disabled D = Carriage Return disabled
CR enabled = Carriage Return enabled
CHARS / INCH
Font selection:
A = 11 cpi, B = 15 cpi
A = 15 cpi, B = 20 cpi D
A = 20 cpi, B = 25 cpi
NOTE:
CPI = Characters Per Inch
37
CODE TABLE [num]
Identiier number of the character code table to use.
The numeric value of the identiier is made up with the following two parameters for the
setting of two digits for the tens and the units:
Setting the digit for tens:
CODE TABLE [num x 10]
0D
1
2
3
4
5
Setting the digit for units:
CODE TABLE [num x 1]
0D
1
2
3
4
5
6
7
8
9
NOTE:
See the paragraph 7.5 to learn about the character tables corresponding to the identiication numbers set with this parameter.
The character tables set with this parameter are the same set with the command 0x1B 0x74 (refer to the
Commands Manual of the device).
FONT TYPE
Setting of the font type:
International D
=
Chinese GB18030 =
Korean PC949
=
Enables the use of the 256 characters font tables
Enables the use of the chinese extended font GB18030-2000
Enables the use of the korean font PC949
NOTE: When the "INTERNATIONAL" font is enabled, you need to choose the character code table (parameter
“CODE TABLE”). When the Chinese or Korean fonts is enabled, the selection of the character code table
is suspended (parameter “CODE TABLE”).
SPEED / QUALITY
Setting of printing speed and printing quality:
Normal
High Quality
High Speed D
PAPER THRESHOLD
Threshold value (in percent) for the recognition of the presence of paper by the paper
presence sensor:
30%
40% D
50%
60%
USB VIRTUAL COM
70%
80%
90%
Setting the USB port as a virtual serial port:
Disabled D
Enabled
= Virtual COM disabled
= Virtual COM enabled
NOTE: To use this coniguration it is necessary to install an additional driver.
38
PAPEREND BUFFER
CLEAR
PRINT DENSITY
Cleaning mode of the data in receive buffer, if the printing is stopped due to lack of paper:
Disabled D = The data remain in the receive buffer. When the paper runs out, the device
keeps the remaining data in the receive buffer and prints the remaining
portion of the ticket after that the new paper is loaded.
Enabled = When the paper runs out, all data in the receive buffer are deleted.
Adjusting the printing density:
-25%
-12%
0D
+12%
+25%
39
5.5
Hexadecimal dump
This function is used for the diagnosis of the characters received from the communications port. Characters are printed as
hexadecimal code and the corresponding ASCII code (see below). Each line is preceded by a counter in hexadecimal that
indicates the number of bytes received.
During the startup, if you hold down the LINE FEED key, the device enters the self-test routine and print the setup report.
The device remains in standby until a key is pressed or characters are received through the communication port (Hexadecimal Dump mode). For each character sent, the ticket shows the hexadecimal value and the ASCII codes (if the characters
are underlined, the receive buffer is full). Shown below is an example of a Hexadecimal Dump:
HEXADECIMAL DUMP
31
39
37
68
73
66
65
6F
6F
77
72
6B
64
73
66
6A
40
32
30
38
6B
64
73
69
72
75
65
69
6C
66
64
6B
6B
33
31
39
6A
66
64
6F
69
77
72
6F
73
6B
66
F2
6C
34
32
75
73
6B
66
79
75
65
69
75
64
73
6B
6A
68
35
33
69
64
6A
6B
75
77
72
6F
77
66
64
6A
73
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
12345 ...
90123 ...
789ui ...
hkjsd ...
sdfkj ...
fsdfk ...
eioyu ...
oriuw ...
ouwer ...
werio ...
riouw ...
klsdf ...
dfksd ...
sdfkj ...
fk≥j ...
jklh
6
MAINTENANCE
6.1
Printer paper jam
1
3
Cut the paper at the entrance of the
printing mechanism as shown in figure.
Unlock the printing mechanism
as shown in figure.
4
2
Remove the rewinder plastic disk and
the damaged paper as shown in figure.
Be careful not to damage
the connection cable
for the printing mechanism
Remove the damaged paper if present under
the printing mechanism and the paper roll with the pin.
41
5
Insert the paper into the device
(see previous paragraphs).
42
6.2
Planning of cleaning operations
The regular cleaning of the device keeps the print quality and extends its life. The following table shows the recommended
planning for the cleaning operations.
EVERY PAPER CHANGE
Printing head
Use isopropyl alcohol
Rollers
Use isopropyl alcohol
EVERY 5 PAPER CHANGES
Sensors
Use compressed air
EVERY 6 MONTHS OR AS NEEDED
Case
Use compressed air or a soft cloth
For speciic procedures, see the following pages.
NOTES:
If you use the device in dusty environments, you must reduce the intervals between the cleaning operations.
43
6.3
Cleaning
For periodic cleaning of the device, see the instructions below.
Printing head
1
3
Disconnect the power supply cable.
2
ISOPROPYL ALCOHOL
ATTENTION:
Do not use solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
ON
Clean the printing head by using
a non-abrasive cloth moistened with isopropyl.
Unlock the printing mechanism
as shown in figure.
44
Printing roller
1
3
ISOPROPYL ALCOHOL
Disconnect the power supply cable.
2
ATTENTION:
Do not use solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
ON
Clean the printing roller by using
a non-abrasive cloth moistened with isopropyl.
Unlock the printing mechanism
by following the procedure as described
in the previous paragraphs.
45
Sensor for paper presence in input
1
3
Disconnect the power supply cable.
2
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
ON
Alcohol, solvent
Clean the paper presence sensor in input
by using compressed air.
Unlock the printing mechanism
by following the procedure as described
in the previous paragraphs.
46
Case
1
Disconnect the power supply cable.
2
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
ON
Alcohol, solvent
To clean the device,
use compressed air or a soft cloth.
47
6.4
Upgrade irmware
9. Select the serial communication port (e.g. COM1):
Select the system communication port
WARNING: During communication between PC and
device for the irmware update it is strictly forbidden to disconnect the communication cable or to remove the
power supply of the devices not to endanger the proper
functioning of the machine.
NOTES:
The latest irmware is available in the DOWNLOAD area of the web site www.custom.biz
Available port
OK
COM1
Firmware rel.:COM2None
COM3
Hardware rel.:COM4None
COM5
PSW Version :
None
COM6
File [*.cfg] :
None
Printer type:
None
Cancel
Select port:
None
Selected port
COM1
File (*.psw):
C:\<device>.PSW
Select (*.psw):
Install on the PC used for device upgrading the UPGCEPRN software available in the download area of the
web site www.custom.biz.
Begin upgrade
Data flush status...
Upgrade status:
Port config:
No upgrade thread active...
Communication port not init
Update via serial interface
Proceed as follows:
1. Write down the product code (14 digits) printed on the
product label (see par.2.3).
2. Go to the web site www.custom.biz and download the
appropriate irmware release from the DOWNLOAD area.
3. Print the SETUP report (see chapter 5).
4. Switch OFF the device.
5. Connect the device to the PC using a serial cable (see
par. 3.2).
6. Switch ON the device.
7. Launch the software UPGCEPRN.
8. Select the update ile .PSW location:
10. Detecting and setting of the parameters necessary for
serial communication are performed automatically and
then updating begins.
11. After a few minutes a message on the screen warns
that the update is completed.
Upgrade OK
Upgrade succesfully completed.
OK
12. Print a new SETUP report to verify the new irmware release (see chapter 5).
Firmware rel.:
None
Printer type:
None
Hardware rel.:
None
Select port:
None
PSW Version :
None
File [*.cfg] :
None
File (*.psw):
Select (*.psw):
Begin upgrade
Data flush status...
Upgrade status:
No upgrade thread active...
48
Port config:
Communication port not init
Update via USB interface
Select Printer
ATTENTION:
Only during the irmware update, the connection between PC and device must be direct, without the use
of HUB device.
<device1>
<device2>
<device3>
<device4>
<device5>
Only during the irmware update, do not connect or disconnect other USB devices.
Selected Printer
NOTE: For communication via USB you must install on
PC the device driver available in the DOWNLOAD area
of the web site www.custom.biz.
<device1>
OK
Port filtering...
Cancel
USB
Select the system communication port
Available port
OK
COM4
Firmware rel.:COM5None
COM6
Hardware rel.:COM7None
COM9
PSW Version :
None
USB
File [*.cfg] :
None
Proceed as follows:
1. Write down the product code (14 digits) printed on the
Printer type:
None
Cancel
Select port:
None
Selected port
USB
File (*.psw):
C:\<device1>.PSW
product label (see par.2.3).
2. Go to the web site www.custom.biz and download the
Select (*.psw):
Begin upgrade
appropriate irmware release from the DOWNLOAD Data flush status...
area.
3. Print the SETUP report (see chapter 5).
4. Switch OFF the device.
Upgrade status:
5. Connect the device to the PC using a USB cable (see
Port config:
No upgrade thread active...
Communication port not init
par. 3.2).
6. Switch ON the device.
7. Launch the software UPGCEPRN.
10. After a few minutes a message on the screen warns
that the update is completed.
8. Select the update ile .PSW location:
Firmware rel.:
None
Printer type:
None
Hardware rel.:
None
Select port:
None
PSW Version :
None
File [*.cfg] :
None
Upgrade OK
Upgrade succesfully completed.
OK
File (*.psw):
Select (*.psw):
Begin upgrade
11. Print a new SETUP report to verify the new irmware release (see chapter 5).
Data flush status...
Upgrade status:
No upgrade thread active...
Port config:
Communication port not init
9. Select item USB and then select the USB device among
those proposed (e.g. device1):
49
50
7
SPECIFICATION
7.1
Hardware speciications
Operating temperature
Sensors
PRT80III (standard models)
Head temperature, paper presence in input,
printing head lifted, near paper end
PRT80III (models with encoder)
Head temperature, paper presence in input,
printing head lifted, near paper end, antijam
MTBF (1)
Emulations
Printing driver
122 000 hours
CUSTOM/POS, PRT80, CUSTOM TPT
Windows XP
VISTA (32/64bit)
Windows 7 (32/64bit)
Windows 8 (32/64bit)
Windows 8.1 (32/64bit)
Android
INTERFACES
USB port
RS232 serial port
12 Mbit/sec (USB 2.0 full speed)
from 1200 to 115200 bps
MEMORIES
Receive buffer
16 Kbytes
Flash memory
1 Mbytes internal, 4 Mbytes external (of which 1Mbyte available for user)
RAM memory
128 Kbytes internal + 8Mbytes external
PRINTER
Resolution
Printing method
Head life (2)
203 dpi (8 dot/mm)
Thermal, ixed head
50 km
51
Printing width
76 mm
Printing mode
Normal, 90°, 180°, 270°
Printing format
Character fonts
Printable barcode
Printing speed (2) (3)
Height/Width from 1 to 8, bold, reverse, underlined, italic
54 character code tables (see par. 7.5)
Extended chinese GB18030-2000, Korean PC949
UPCA, UPCE, EAN13, EAN8, CODE39, ITF,
CODABAR, CODE93, CODE128, CODE32,
PDF417, DATAMATRIX, AZTEC, QRCODE
High quality = 80 mm/s
Normal = 115 mm/s
High Speed = 140 mm/s
PAPER
Type of paper
Paper width
Paper weight
Paper thickness
Recommended types of paper
External roll diameter
External roll core diameter
Thermal rolls, heat-sensitive side on outside of roll
80 ± 0,5 mm
from 58 g/m2 to 80 g/m2
from 63 µm to 80 µm
KANZAN KF50 and KP460
MITSUBISHI PF5067 and TL4000
max 100 mm
25 mm (+ 1mm)
Paper end
Not attached to roll core
Core type
Cardboard or plastic
DEVICE ELECTRICAL SPECIFICATIONS
Power supply
24 Vdc ±10% (optional external power supply)
Medium consumption (4)
2.5 A
Typical consumption (5)
1.2 A
Stand-by consumption
0.05 A
52
ELECTRICAL SPECIFICATIONS POWER SUPPLY cod.963GE020000003 (OPTIONAL)
Power supply voltage
from 100 Vac to 240 Vac
Frequency
from 50 Hz to 60 Hz
Current (output)
2.5 A
Power
60 W
ENVIRONMENTAL CONDITIONS
Operating temperature
Relative humidity
Storage temperature
Storage relative humidity
from 0°C to +50°C
from 10% Rh to 85% Rh
from -20 °C to +70 °C
from 10% Rh to 90% Rh
NOTES:
(1) : Control board.
(2) : Respecting the regular schedule of cleaning for the device components.
(3) : Referred to a standard CUSTOM receipt (L=10cm, Density = 12,5% dots on).
(4) : Referred to the UL measurements (L = 10cm, Density = 50% dot on, Print density = +50%).
(5) : Referred to a standard CUSTOM receipt (L=10cm, Density = 12,5% dots on).
53
7.2
Character speciications
"CUSTOM/POS" emulation
Character set
Character density
3
11 cpi
15 cpi
20 cpi
32
41
57
Chars / sec
1472
1886
2622
Lines / sec
46
46
46
2,25 x 3
1,75 x 3
1,25 x 3
Number of columns
Characters (L x H mm)-Normal
"PRT80" emulation and "CUSTOM TPT" emulation
Character set
Character density
3
11 cpi
15 cpi
20 cpi
31
40
56
Chars / sec
1426
1840
2576
Lines / sec
46
46
46
2,25 x 3
1,75 x 3
1,25 x 3
Number of columns
Characters (L x H mm)-Normal
NOTE: Theoretical values.
54
7.3
Device dimensions
Length
210 mm
Height
178.5 mm
Width
136 mm
Weight
1550 g
178.5
NOTES:
Dimensions referred to devices without paper roll.
All the dimensions shown in following igures are in millimetres.
13
102
128
136
15
143
180
188.3
210
55
7.4
Dimensions of power supply cod. 963GE020000003 (optional)
PRT80III
Length
127 mm
Height
35.5 mm
Width
56 mm
35,5
NOTE:
All the dimensions shown in following igures are in millimetres.
AC INLET
56
N.C
2 1
3
GND
127
DC OUTPUT WIRE
56
+24V
7.5
Character sets
The device has 3 fonts of varying width (11, 15 and 20 cpi) which may be related one of the coding tables provided on the
device.
To know the coding tables actually present on the device, you need to print the font test (see par.2.4).
You can set font and coding table by using the commands (see the Commands Manual of the device) or using the “Code
Table”, "Chars / Inch" and "Font Type" parameters during the Setup procedure (see par.5.4).
The following is the full list of coding tables that can be installed on the device.
<CodeTable>
Coding table
0
PC437 - U.S.A., Standard Europe
1
Katakana
2
PC850 - Multilingual
3
PC860 - Portuguese
4
PC863 - Canadian/French
5
PC865 - Nordic
11
PC851 - Greek
on request
12
PC853 - Turkish
on request
13
PC857 - Turkish
on request
14
PC737 - Greek
on request
15
ISO8859-7 - Greek
on request
16
WPC1252
17
PC866 - Cyrillic 2
18
PC852 - Latin 2
19
PC858 for Euro symbol at position 213
20
KU42 - Thai
on request
21
TIS11 - Thai
on request
26
TIS18 - Thai
on request
30
TCVN_3 - Vientamese
on request
31
TCVN_3 - Vientamese
on request
32
PC720 - Arabic
on request
on request
57
<CodeTable>
58
Coding table
33
WPC775 - Baltic Rim
on request
34
PC855 - Cyrillic
on request
35
PC861 - Icelandic
on request
36
PC862 - Hebrew
37
PC864 - Arabic
38
PC869 - Greek
on request
39
ISO8859-2 - Latin 2
on request
40
ISO8859-15 - Latin 9
on request
41
PC1098 - Farci
on request
42
PC1118 - Lithuanian
on request
43
PC1119 - Lithuanian
on request
44
PC1125 - Ukranian
on request
45
WPC1250 - Latin 2
46
WPC1251 - Cyrillic
47
WPC1253 - Greek
48
WPC1254 - Turkish
49
WPC1255 - Hebrew
50
WPC1256 - Arabic
51
WPC1257 - Baltic Rim
52
WPC1258 - Vientamese
53
KZ1048 - Kazakhstan
255
Space page
on request
8
CONSUMABLES
The following table shows the list of available consumables for device:
DESCRIPTION
CODE
67300000000393
THERMAL PAPER ROLL
width = 80mm
Ø external = 48mm
Ø core = 25mm
67300000000395
THERMAL PAPER ROLL WITH BACK SIDE PRE-PRINTED
width = 80mm
Ø external = 48mm
Ø core = 25mm
59
60
9
ACCESSORIES
The following table shows the list of available accessories for device:
DESCRIPTION
CODE
963GE020000003
POWER SUPPLY
(for technical speciications, see the paragraph 7.1)
ADAPTER CABLE
3 pin male power-DIN connector
0.5 mt
26600000000012
26500000000352
SERIAL CABLE
9 pin male connector - 9 pin female connector
1.8 mt
USB CABLE
AB type
1.8 mt
26500000000356
61
62
10
TECHNICAL SERVICE
In case of failure, contact the Technical Service by sending an e-mail detailing:
1. Product code
2. Serial number
3. Hardware release
4. Firmware release
To get the necessary data, proceed as follows:
1
3
XXXXXXXXXXXXXX
Rx
0000000000000000000
Customer Service Department:
[email protected]
Write down the data printed
on the product label (see par.2.3).
(worldwide)
or
[email protected]
2
(specific for North/South American customers)
FW
Send an e-mail to the Technical Service,
with the data collected.
PRT80III
SCODE. <code>
DCODE. <code>
FCODE. <code>
-
rel 1.00
rel 1.00
rel 1.00
PRINTER SETTINGS
PRINTER TYPE .................................... TPTCMIII
PRINTING HEAD TYPE ........................ SHEC C72
INTERFACE ......................................... USB
PROGRAM MEMORY TEST ................ OK
DYNAMIC RAM TEST ......................... OK
EXTERNAL MEMORY TEST ................ OK
HEAD VOLTAGE [V]
= 24.12
Print a Setup report (see paragraph 5.1)
The Setup report shows
the firmware release.
63
64
11
ADVANCED FUNCTIONS
11.1
File sharing
The device can be connected to a PC with a USB cable.
Through this kind of connection, it is possible to manage drivers, fonts and logos of the device and conigure the operating parameters by iles sharing from Mass Storage.
USB
FILE SHARING
FROM
MASS STORAGE
11.2
Drivers installation
It is possible to install the new driver update directly into the folder “DRIVER” on the Flash Drive of the device.
To enter the Flash Drive by iles sharing from Mass Storage you need to enable the relative parameter during the coniguration process (see chapter 5).
65
11.3
Logos management
It is possible to store new logos in addition to default logos stored on Flash Disk. The device automatically provides to
convert BMP image to the error-diffusion format in black and white.
It is possible to directly add the new logo directly into the folder “PICTURES” on the Flash Drive of the device.
To enter the Flash Drive by iles sharing from Mass Storage, you need to enable the relative parameter during the coniguration process (see chapter 5).
After adding the logo, open the coniguration ile “PictList.ini” and add a new line with a number associated to the logo (to be used with device’s commands), a letter for the memory unit and the logo ile name, as indicated in the instructions written inside the “PictList.ini” ile.
To delete a logos stored in the device, proceed as follows:
1. delete the selected logo from the “Pictures” folder on Flash Disk;
2. in the coniguration ile “PictList.ini”, delete the line related to the erased logo.
The logos stored on Flash Disk and converted by the device, can be printed by using the number associated to the logo
during the conversion step.
The correspondence between ile-name and logo-number is warrant by the coniguration ile “PictList.ini” and it is veriiable with the logo test.
11.4
Fonts management
It is possible to store new font in addition to default fonts stored on Flash Disk.
You can directly add the new font directly into the folder “FONTS” on the Flash Drive of the device.
To enter the Flash Drive by iles sharing from Mass Storage, you need to enable the relative parameter during the coniguration process (see chapter 5).
NOTE:
Uploading the new font directly from the “Font” folder of Microsoft® Windows® directory, remember that the displayed
font name into the “Font” folder may not match the real name of the font ile.
66
11.5
Setup
It is possible to conigure the default parameters for device setup by editing the “Setup.ini” ile on the Flash Drive.
To enter the Flash Drive by iles sharing from Mass Storage, you need to enable the relative parameter during the coniguration process (see chapter 5).
After editing device’s parameter, simply save the “Setup.ini” ile to make the modiies activated.
The “Setup.ini” ile is a coniguration ile that contains all the conigurable parameters listed in text format and divided into some sections (indicated in square brackets).
The available values for every parameter, are listed after the parameter name. The value marked with the symbol ‘ * ’ is the
default one. To modify printer’s parameters, change the numeric value after the name of parameters. To set the parameter
to the default value, change the numeric value with the symbol D.
The “Setup.ini” ile permits the coniguration of the following parameters:
[PRINT]
Printer Emulation
0*, 1, 2
0 = CUSTOM/POS
1 = PRT80
2 = CUSTOM TPT
Print Mode
0*, 1
0 = Normal
1 = Reverse
Autofeed
0*, 1
0 = CR disabled
1 = CR enable
Chars / inch
0, 1*, 2
0 = A=11 B=15 cpi
1 = A=15 B=20 cpi
2 = A=20 B=15 cpi
Code Table [num]
0*
Font Type
0*, 1, 2
0 = International
1 = Chinese GB18030
2 = Korean CP949
Speed / Quality
0, 1, 2*
0 = High Quality
1 = Normal
2 = High Speed
Paper Threshold
0, 1, 2, 3*, 4, 5, 6
0 = 30 %
1 = 40 %
2 = 50 %
PaperEnd Buffer Clear
0*, 1
0 = Disabled
1 = Enabled
Print Density
2, 3, 4*, 5, 6
2 = - 25 %
3 = - 12 %
4=0%
3 = 60 %
4 = 70 %
5 = 80 %
6 = 90 %
5 = + 12 %
6 = + 25 %
67
[INTERFACE]
RS232 Baud Rate
1, 2, 3, 4, 5, 6, 7, 8*
1 = 1200 bps
2 = 2400 bps
3 = 4800 bps
RS232 Data Length
0*, 1
0 = 8 bits/chr
1 = 7 bits/chr
RS232 Parity
0*, 1, 2
0 = None
1 = Even
2 = Odd
RS232 Handshaking
0, 1*
0 = Xon/Xoff
1 = Hardware
Busy Condition
0*, 1
0 = RxFull
1 = OffLine/RxFull
USB Mass Storage
0*, 1
0 = Disabled
1 = Enabled
USB Address Number
0*, 1, 2, 3, 4, 5, 6, 7, 8, 9
0=0
1=1
2=2
3=3
USB Virtual COM
0*, 1
0 = Disabled
1 = Enabled
68
4 = 9600 bps
5 = 19200 bps
6 = 38400 bps
7 = 57600 bps
8 = 115200 bps
4=4
5=5
6=6
7=7
8=8
9=9
69
Rev.1.00
Part Number : 76200000005600
CUSTOM S.p.A.
World Headquarters
Via Berettine, 2/B - 43010 Fontevivo, Parma ITALY
Tel. +39 0521 680111 - Fax +39 0521 610701
[email protected] - www.custom.biz
All rights reserved
www.custom.biz
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement