air compressor - Canadian Tire

air compressor - Canadian Tire
model no. 058-9316-0
AIR COMPRESSOR
IMPORTANT:
Read and understand this instruction manual thoroughly before using the
product. It contains important information for your safety as well as
operating and maintenance advice.
INSTRUCTION
MANUAL
TABLE OF CONTENTS
TECHNICAL SPECIFICATIONS
SAFETY GUIDELINES
KEY PARTS DIAGRAM
KEY PARTS LIST
INTENDED USE
ASSEMBLY
OPERATING INSTRUCTIONS
MAINTENANCE
TROUBLESHOOTING
EXPLODED VIEW
PARTS LIST
WARRANTY
NOTE:
If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline
at 1-800-689-9928.
SAVE THESE INSTRUCTIONS
Keep this instruction manual for future use. Should this product be passed on to a third party,
then this instruction manual must be included.
4
5
8
9
10
12
14
18
20
22
23
24
TABLE OF CONTENTS
3
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
5
model no. 058-9316-0 | contact us 1-800-689-9928
RUNNING HP
TANK SIZE
AIR DELIVERY (CFM*) @ 40 PSI
AIR DELIVERY (CFM*) @ 90 PSI
CUT-IN PRESSURE (PSI)
CUT-OUT PRESSURE (PSI)
PUMP DESIGN
MOTOR
POWER
WEIGHT
POWER CORD
EXTENSION CORD
1.5
8 U.S. GALLONS (30.3 L)
4.8
3.5
105
135
Oil-less, direct-drive, single-stage
3,400 RPM
120 V, 60 Hz, 12 A
57 lb 3 oz (26 kg)
SJT 16 AWG / 72" (1.83 m)
SJT 12 AWG / Maximum 30 (9.1 m)
This manual contains information that relates to PROTECTING PERSONAL SAFETY
and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual
carefully and understand it thoroughly before using the product. The symbols listed
below are used to indicate this information.
Safety Advice
1.
RISK OF FIRE OR EXPLOSION. Do not spray a flammable or combustible liquid or paint
near sparks, flames, pilot lights or in a confined area. The spray area must be well-ventilated.
Keep compressor at least 20' (6 m) away from spray area. Do not carry and operate the
compressor or any other electrical device near the spray area. Never smoke when spraying.
Use a minimum of 25' (7.6 m) of hose to connect a spray gun to the compressor.
2.
RISK OF ELECTRIC SHOCK. Do not expose to rain. Store the compressor indoors. Hazardous
voltage. Disconnect from power source before servicing. Compressor must be grounded. Do
not use grounding adaptors.
3.
RISK OF BURSTING. Make sure the regulator is adjusted so that the compressor outlet
pressure is set lower than the maximum operating pressure of the spray gun or tool. Before
starting the compressor, pull the ring on the safety valve to make sure the valve moves freely
(see diagram on page 17). Drain water from tank after each use. Do not weld or repair tank.
4.
. Never spray the compressed air or material at self or others.
RISK OF PERSONAL INJURY.
5.
RISK OF BURSTING. Check the maximum pressure rating in the manual or identification
label. The compressor outlet pressure must be regulated so that it does not exceed the
maximum pressure rating. Relieve all pressure in the hose before removing or attaching
accessories.
6.
RISK OF BURSTING. Do not adjust the pressure switch or safety valve for any reason. They
have been preset at the factory for this compressor’s maximum pressure. Tampering
with the pressure switch or the safety valve may cause personal injury or property damage.
*CFM: Cubic feet per minute.
IMPORTANT!
Installation, operation or maintenance information that is important but not hazard related.
DANGER!
Potential hazard that will result in serious injury or loss of life.
WARNING!
Potential hazard that could result in serious injury or loss of life.
CAUTION!
Potential hazard that may result in moderate injury or damage to equipment.
SAFETY GUIDELINES
4
7
model no. 058-9316-0 | contact us 1-800-689-9928
7.
RISK OF BURNS. The pump and the manifold generate high temperatures. In order to
avoid burns or other injuries, do not touch the pump, the manifold or the transfer tube
while the compressor is running . Allow the parts to cool down before handling or
servicing. Keep children away from the compressor at all the times.
8.
RISK OF BREATHING. Be certain to read all labels when you are spraying paints or
toxic materials, and follow all safety instructions. Use a respirator mask if there is a
chance of inhaling anything you are spraying. Also, NEVER directly inhale the air
produced by a compressor.
As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using
extension cords with inadequa tely sized wire causes a serious drop in voltage, resulting in loss of power
and possible product damage. Refer to the table here to determine the required minimum wire size.
Recommended Minimum Wire Gauge for Extension Cords* (120 V)
RISK OF EYE INJURY. Wear ANSI Z87.1 approved safety goggles when using an air
compressor. Do not point any nozzle or sprayer toward a person or any part of the
body. Serious injury may occur if the spray penetrates the skin.
AMPERE
RATING
0–5
5.1 – 8
8.1 – 12
12.1 – 15
15.1 – 20
SAFETY GUIDELINES
9.
Extension cords
CORD SIZE IN AWG (AMERICAN WIRE GAUGE)
Extension cord length in feet
25' 50'
75' 100' 150'
16 16
16
14
12
16 16
14
12
10
14 14
12
10
—
12 12
10
10
—
10 10
10
—
—
200'
12
—
—
—
—
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge
cord can carry a higher current than a 16-gauge cord. When using more than one extension cord to make
up the total length, be sure each cord contains at least the minimum wire size required.
Guidelines for using extension cords
WARNING!
Pull the pressure safety valve ring every day in order to ensure that the valve is functioning properly.
The compressor must be located in a well-ventilated area for cooling, and must be a minimum of 12"
(31 cm) away from the nearest wall.
Protect the air hose and the power cord from damage and puncture. Inspect them for weak or worn spots
every week, and replace them if necessary.
Always wear hearing protection when using an air compressor. Failure to do so may result in hearing loss.
Do not carry the compressor while it is running.
Do not operate the compressor if it is not in a stable position.
Do not operate the compressor on a rooftop or an elevated position that could allow the unit to fall or be
tipped over.
Always replace a damaged gauge before operating the unit again.
•
If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A"("W" in
Canada) to indicate it is acceptable for outdoor use.
•
Ensure your extension cord is properly wired and in good electrical condition. Alway replace a
damaged extension cord or have it repaired by a qualified technician before using it.
•
Protect your extension cords from sharp objects, excess heat and damp or wet areas.
SAFETYSAFETY
GUIDELINES
SPECIFIC
GUIDELINES FOR THE SLIDING WET TILE SAW
6
8
9
model no. 058-9316-0 | contact us 1-800-689-9928
A. ELECTRIC MOTOR: The motor is used to power the pump. It is equipped with a thermal overload
protector. If the motor overheats for any reason, the thermal overload protector will shut it down in order
to prevent the motor from being damaged.
KEY PARTS DIAGRAM
G
C. ON/OFF SWITCH: This switch turns the compressor on and off. It is operated manually and when
it is in the ON position, it allows the motor to start if the pressure in the air tank is below the factory set
cut-in pressure, and allows the motor to stop if the pressure in the air tank reaches the factory set cut-out
pressure. Be sure to set this switch to the OFF position when the compressor is not being used and before
unplugging the compressor.
D. SAFETY VALVE: This valve is used to prevent system failure by draining pressure from the system
when it reaches a preset level if the pressure switch has not shut down the motor. It will pop open
automatically, or it can be activated manually by pulling the ring on the valve.
E. AIR PRESSURE REGULATOR: The regulator is used to adjust the pressure inside the line to the tool
that is being used. Turn the knob clockwise to increase the pressure and counter-clockwise to decrease
the pressure.
F. TANK PRESSURE GAUGE: The gauge measures the pressure level of the air that is stored in the
tank. It cannot be adjusted by the operator and it does not indicate the pressure inside the line.
E
G. OUTLET PRESSURE GAUGE: The gauge measures the regulated outlet pressure.
H. AIR OUTLET: The outlet is connected to the 1/4” (6.4 mm) NPT air hose.
H
I. AIR TANK DRAIN VALVE: The drain valve is used to remove moisture from the air tank after the
compressor is shut off.
J. AIR TANK: The tank is where the compressed air is stored.
K. POWER CORD: This compressor should be used on a nominal 120 V grounded circuit. Use a power
cord that is equipped with a grounding plug. Verify that the compressor is plugged into an outlet that has
the same configuration as the plug. Do not use an adaptor with this compressor.
K
Plug
J
Grounded
outlets
I
Grounding pin
WARNING!
Do not exceed the tool’s maximum working pressure.
WARNING!
Do not attempt to open the drain valve when there is more than 10 PSI of air pressure in the tank.
KEY PARTS LIST
F
D
B
A
C
B. AIR COMPRESSOR PUMP: The pump compresses the air and discharges it into the tank via the piston
that moves up and down in the cylinder.
10
11
model no. 058-9316-0 | contact us 1-800-689-9928
Before you start
This Mastercraft® Air Compressor is ideal for a wide range of applications, from fastening to greasing
and engine cleaning. The 8-gallon (30.3 L) design provides optimum pressure. It features a 1.5 HP
induction motor for quiet operation and a cast-iron, oil-free pump for long-lasting, reliable performance.
Tool Compatibility Chart
Operates Tool Operates Tool
Continously Intermittently
Air Tool
Inflation/Recreation
The procedures described in this manual are solely for this 8-gallon (30.3 L) air compressor at a
maximum of P=135 PSI. The device has been designed / constructed for household use only.
Brad Nailer (18 gauge)
Compatible compressor and air tool-proper usage and operation
Finishing Nailer (16 gauge)
Always ensure the use of appropriately matched air tools with your Mastercraft Air Compressor. Be
sure that the air compressor being used can supply the appropriate volume, pressure and delivery
rate of air to the tool(s) without running continuously. Using tools or combinations of tools that,
together or separately, require more than the air compressor can deliver will void the air compressor
guarantee/warranty.
Not
Recommended
3-in-1 Brad/Finishing/Stapler
Framing Nailer
Roofing Nailer
Flooring Nailer
Impact Wrench
Die Grinder/Angle
Grinder/Air Ratchet
Cut-Off Tool
Drill, Hammer/Chisel
Shears
Sander & Polisher
DIY Paint Sprayers
Grease/Caulking Gun
WARNING!
•
This air compressor is not designed for continuous operation or unlimited commercial operations
and may be used in dry area only. This air compressor is intended to be used in maximum
30-minute intervals and should rest for 30 minutes before used again. Do not exceed the
maximum working time.
INTENDED USE
INTENDED USE
®
12
13
model no. 058-9316-0 | contact us 1-800-689-9928
Assembly
1.
Unpack the air compressor unit. Inspect the unit for damage. If the unit has been damaged, contact the
retailer immediately.
THE CARTON SHOULD CONTAIN:
•
•
•
Air compressor
Owner’s manual
Air filter
4. Wheel assembly
• Insert the axle (1) through one of the wheels.
• Insert axle (1) through the bracket on the bottom of the tank assembly. Slide on washer (2), lock
washer (3) and tighten the nut (4).
• Once assembled, roll the air compressor to test the operation of the wheels. Periodically check to
ensure that wheel and axle hardware is secure.
4
3
3. Positioning of the air compressor:
• Position the air compressor (1) near an electrical outlet (2).
• The compressor must be at least 12" (31 cm) from any wall (3) or obstruction, in a clean,
well-ventilated area to ensure sufficient air flow and cooling.
• Place the air compressor on the floor or a hard, level surface. The air compressor must be level to
ensure proper drainage of the moisture in the tank.
2
1
5. Air filter assembly
• Screw the air filter (1) onto the pump.
Wall
6. Removable handle assembly
• Insert handle into the fixed steel sleeves. Align the tapped holes (1) with the holes
on the steel sleeve.
• Fasten the handle to the sleeves using the thumbscrews (2).
NOTE:
¼" (6.4 mm) NPT air hose is required for connecting to the air compressor.
ASSEMBLY
ASSEMBLY
2. Check the air compressor’s identification label to ensure that you have purchased the intended model
and that it has the required pressure rating for its intended use.
14
15
model no. 058-9316-0 | contact us 1-800-689-9928
Break-in procedure
5. Set the ON/OFF switch (1) to the ON (I) position. The compressor will start. Run the compressor for
30 minutes. If it fails, turn it off immediately and call the toll-free helpline at: 1-800-689-9928.
Please note that breaking-in the unit is only required prior to first use.
2. Open the tank drain valve (1) by turning it counter-clockwise to permit the air to escape
and prevent air pressure build-up in the air tank during the break-in period.
6. After 30 minutes, turn off the switch.
7. Close the tank drain valve (I) by turning it clockwise.
3. Turn the air pressure regulator knob (1) counter-clockwise until it stops.
8. Set the ON/OFF switch to the ON (I) position. The air receiver will fill to cut-out pressure
and then the compressor’s motor will stop. The compressor is now ready for use.
4. Plug in the power cord (K).
NOTE:
A circuit breaker is recommended. If the air compressor is connected to a circuit protected by a fuse, use
dual element time delay fuses (type “T” only).
CAUTION!
Use a dedicated circuit.
For best performance and reliable starting, the air compressor should be plugged into a dedicated circuit,
as close as possible to the fuse box or circuit breaker.
The compressor will use the full capacity of a typical 15 A household circuit. If any other electrical
devices are drawing from the compressor’ s circuit, the air compressor may fail to start. Low voltage
or an overloaded circuit can result in sluggish starting that causes the motor thermal overload protector
or circuit breaker to trip, especially in cold conditions.
OPERATING INSTRUCTIONS
OPERA
OPERATING INSTRUCTIONS
1. Set the ON/OFF switch (1) to the OFF (O) position.
Before each start-up
OPERATING INSTRUCTIONS
17
model no. 058-9316-0 | contact us 1-800-689-9928
How to start
1. Set the ON/OFF switch (1) to the OFF (O) position.
1. Close the tank drain valve (1). Plug in the power cord (2).
2. Turn the air pressure regualtor knob counter-clockwise until it stops.
2.
Set the ON/OFF switch to the ON (I) position and allow the tank pressure to build.
Motor will stop when tank pressure reaches cut-out pressure.
3. Turn the air pressure regulator knob clockwise until desired pressure is reached.
Shut down procedure
1. Set the ON/OFF switch (1) to the OFF (O) position.
2. Unplug the power cord .
3. Reduce the pressure in the tank through the outlet hose. Pulling the safety valve
ring and keeping it open, will also reduce the pressure in the tank.
3. Attach hose (1) and accessories.
WARNING!
Risk of bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s
maximum pressure rating for air tools and accessories. The regulator outlet pressure must never exceed
the maximum pressure rating.
WARNING!
If the pump has been transported or turned upside down (even partially), allow the pump to sit in a normal,
upright position for approximately 10 minutes before starting.
WARNING!
High temperatures are generated by the electric motor and the pump. To prevent burns or other injuries,
DO NOT touch the air compressor while it is running. Allow it to cool before handling or servicing. Keep
children away from the air compressor at all times.
CAUTION!
Escaping air and moisture can propel debris that may cause eye injury. Wear safety goggles when opening the
drain valve.
WARNING!
To avoid personal injury, always shut off and unplug the unit, and relieve all air pressure from the system before
performing any service on the air compressor.
WARNING!
Risk of unsafe operation. Unit cycles automatically when power is on. When performing maintenance, you may be
exposed to voltage sources, compressed air or moving parts. Personal injuries can occur. Before performing any
maintenance or repair, disconnect power source from the compressor and bleed off all air pressure.
OPERATING INSTRUCTIONS
16
ITEM
MAINTENANCE
19
model no. 058-9316-0 | contact us 1-800-689-9928
DESCRIPTION/REASON
SERVICE
INTERVAL
Through normal operation of your air compressor, condensation water
will accumulate in the tank. To prevent corrosion of the tank from the
inside, condensation must be drained at the end of every workday.
Note: Allow unit to cool before draining tank. Drain valve(I) becomes hot
during operation.
• Set the ON/OFF switch to the OFF position.
• Unplug the power cord.
Drain
• Turn air pressure regulator knob counter-clockwise to set the outlet
the tank pressure to zero.
• Pull and hold ring on safety valve, allowing air to bleed from the
tank until air pressure is minimized.
• Place suitable container under unit to catch water.
• Slightly tilt unit and turn drain valve (I) counter clockwise to open.
• After the water has been drained, close the drain valve (I) (clockwise).
The air compressor can now be stored.
Daily
Check
Pull/activate the safety valve daily to ensure that it is operating properly
the valve and to clear the valve of any possible obstructions.
Daily
1.
2.
3.
4.
5.
6.
7.
A dirty air filter will reduce air compressor performance and life.To avoid
contaminating the pump, the filter should be cleaned frequently and
replaced on a regular basis. Clean the foam filter by immersing it in
warm, soapy water. Dry thoroughly after.
Weekly
Test for
leaks
Check that all connections are tight. Small leaks in the tank, hoses,
connections or transfer tubes will substantially reduce the air compressor
and tool performance. Spray a small amount of soapy water around the
area of suspected leaks with a spray bottle. If bubbles appear, repair,
replace or re-seal the faulty component. Do not over tighten any
connections.
Monthly
Storage
•
Before starting compressor, pull the ring on the safety valve to make sure
that the safety valve operates freely. If the valve is stuck or does not operate
smoothly, contact a trained service technician.
To drain tank.
Clean
the air
filter
Before storing the air compressor, do the following:
• Drain tank (see Operating Instructions paragraph in the Maintenance
section of this manual for the correct procedure).
• Use an air blow gun to clean all dust and debris from the compressor.
• Disconnect and wind up the power cord.
• Drain all moisture from the tank.
• Pull the pressure safety valve to release all pressure from the tank.
• Cover the entire unit to protect it from moisture and dust.
• Store the air compressor in a clean and dry location.
• In cold weather, store the compressor in a warm building when it is
not in use. This will reduce problems related to starting the motor and
the freezing of water condensation.
To check safety valve
Prior to
storing
Set the ON/OFF switch (C) to the OFF (O) position.
Unplug the power cord (K).
Turn air pressure regulator knob (E) counter-clockwise to set the outlet pressure to zero.
Pull and hold ring on safety valve (D), allowing air to bleed from the tank until air pressure is
minimized.
Place suitable container under unit to catch water.
Slightly tilt unit and turn drain valve (I) counter-clockwise to open.
After the water has been drained, close the drain valve (I) (clockwise). The air compressor can now
be stored.
NOTE:
Allow unit to cool before draining tank. Drain valve (I) becomes hot during operation.
NOTE:
NOTE:
Troubleshooting problems may have similar causes and solutions.
Disconnect the electrical plug and disconnect any tools from air supply before attempting any adjustment.
WARNING!
If any of the following symptoms appears while operating the product, stop using the product immediately,
or serious personal injury could result. Only an authorized service centre should perform repairs on this
product.
WARNING!
Disconnect the electrical plug and disconnect any tools from air supply before attempting any adjustment.
MAINTENANCE
18
PROBLEM
TROUBLESHOOTING
21
model no. 058-9316-0 | contact us 1-800-689-9928
POSSIBLE CAUSES
SOLUTIONS
The power cord is not plugged in. Plug the power cord into a grounded outlet.
The ON/OFF switch is in the
Set the ON/OFF switch to the ON (I) position.
OFF (O) position.
The extension cord is the wrong Check the technical specifications
page
wire gauge or is too long.
7 for the proper wire gauge and cord length.
Turn the air compressor off, unplug the
power cord and wait until the motor has
cooled down. Plug in the power cord only
The motor’s thermal overload
after the motor has cooled down, however
protection has tripped.
wait at least 5 minutes to make sure the
thermal overload protector has recovered.
The motor will
not run or start.
A fuse has blown or a circuit
breaker has been tripped.
Replace the fuse or reset the circuit breaker.
Verify that the fuse has the proper amperage.
Check for low voltage conditions. Disconnect
any other electrical appliances from the
circuit or operate the compressor on a
dedicated circuit.
The air tank pressure exceeds
The motor will start automatically when the
the preset pressure switch limit. tank pressure drops below the cut-in
pressure.
The safety valve is stuck open. Clean or replace the safety valve.
Electrical connections are loose. Have the compressor serviced by a qualified
technician.
The motor, capacitor or safety
Have the compressor serviced by a qualified
valve is defective.
technician.
The pressure switch does not
Set the ON/OFF switch to the OFF position.
shut off the motor when the air If the motor does not shut off, unplug the air
compressor reaches the cut-out compressor. If the pressure switch is
defective, replace it.
The motor runs pressure and the safety valve
activates.
continuously
Check air requirements of the accessory
when the
that is being used. If it is higher than the
pressure switch
CFM (Cubic Feet per Minute,
(page 4)
is in the ON
The compressor’s capacity
and
pressure
supplied
by
the
compressor,
a
position.
is not enough.
larger capacity air compressor is needed.
Most accessories are rated at 25% of actual
CFM while running continuously.
PROBLEM
The regulator
does not
regulate the
pressure.
POSSIBLE CAUSES
The regulator or its internal parts
are dirty or damaged.
SOLUTIONS
Replace the regulator.
The tank drain valve is open.
Check the fittings with soapy water. Tighten
or reseal leaking fittings (apply plumber's tape
on threads). Do not overtighten.
Close the drain valve.
The air intake is restricted.
Clean or replace the air filter element.
There is a leak at one of the
fittings.
The pressure is Prolonged excessive use of air.
low or there is There is a hole in the air hose.
not enough air.
The tank leaks.
The valve is leaking
Decrease the amount of air used.
Check the air hose and replace it if necessary.
Replace the tank immediately. Do not attempt
to repair it.
Check for worn parts and replace them if
necessary.
CAUTION: Always replace a damaged gauge
before operating the unit again.
There is condensation in the air
There is
moisture in the tank caused by a high level of
discharge air. atmospheric humidity or because
the air compressor has not been
running long enough.
The
compressor
overheats.
The ventilation is inadequate.
Cooling surfaces are dirty.
The valve is leaking.
Drain the air tank after each use. Drain the air
tank more often in humid weather and use an
air line filter.
Relocate the compressor to an area with cool,
dry and well-circulated air.
Clean all cooling surfaces on the pump and the
motor thoroughly.
Replace worn parts and reassemble using new
plumber's tape.
TROUBLESHOOTING
20
23
model no. 058-9316-0
055-6740-2 | contact us 1-800-689-9928
19 16 17 21
15
20 22
23
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
24
18
14
EXPLODED VIEW
13
25
27
12
10
11
9
26
29
30
31
8
7
28
19
32
33
5
3
4
2
34
37
36
QTY
4
2
2
1
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
NO.
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DESCRIPTION
QTY
1
Fan
1
Air filter
1
Back shroud
4
Bolt M5x18
Self-tapping screw ST3.9x17 4
4
Bolt M8x25
4
Washer 8
4
Cushion pad
2
Bolt M5x10
2
Lock washer
1
Transfer tube
1
Pressure switch
1
Anchor nut
1
Power cord
2
Shoulder bolt
2
Wheel
4
Washer 10
2
Spring washer 10
If any parts are missing or damaged, or if you have any questions, please call our toll-free
helpline at 1-800-689-9928.
6
1
DESCRIPTION
Nut M 10
Rubber foot
Bolt M 10X20
Drain valve
Air tank
Handle
Thumbscrew
Check valve
Regulator
Relief valve
Quick coupler
Pressure gauge
Front shroud
Switch retainer
On/Off switch
Elbow
Pump/Motor assembly
Capacitor, 50 μf
Capacitor, 200 μf
35
PARTS LIST
22
24
25
model no. 058-9316-0
055-6740-2 | contact us 1-800-689-9928
This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase
against defects in workmanship and materials, except for the following component:
Component A: Accessories, which are guaranteed for a period of 1-year from the date of original retail
purchase against defects in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with proof of
purchase within the stated warranty period and if covered under this warranty, will be repaired or replaced
(with the same model, or one of equal value or specification), at our option. We will bear the cost of any
repair or replacement and any costs of labour relating thereto.
Additional Limitations
This warranty applies only to the original purchaser and may not be transferred. Neither the retailer nor the
manufacturer shall be liable for any other expense, loss or damage, including, without limitation, any
indirect, incidental, consequential or exemplary damages arising in connection with the sale, use or inability
to use this product.
Notice to Consumer
This warranty gives you specific legal rights, and you may have other rights, which may vary from province
to province. The provisions contained in this warranty are not intended to limit, modify, take away from,
disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation.
A. A bill of sale verifying the purchase and purchase date must be provided;
B. This warranty will not apply to any product or part thereof which is worn or broken or which has
become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation,
operation or maintenance (as outlined in the applicable owner’s manual or operating instructions) or
which is being used for industrial, professional, commercial or rental purposes;
C. This warranty will not apply to normal wear and tear or to expendable parts or accessories that may
be supplied with the product which are expected to become inoperative or unusable after a
reasonable period of use;
D. This warranty will not apply to routine maintenance and consumable items such as, but not limited to,
fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments;
E. This warranty will not apply where damage is caused by repairs made or attempted by others (i.e.
persons not authorized by the manufacturer);
F. This warranty will not apply to any product that was sold to the original purchaser as a reconditioned
or refurbished product (unless otherwise specified in writing);
G. This warranty will not apply to any product or part thereof if any part from another manufacturer is
installed therein or any repairs or alterations have been made or attempted by unauthorized persons;
H. This warranty will not apply to normal deterioration of the exterior finish, such as, but not limited to,
scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical
cleaners;
I. This warranty will not apply to component parts sold by and identified as the product of another
company, which shall be covered under the product manufacturer’s warranty, if any.
Made in China
Imported by Mastercraft Canada Toronto, Canada M4S 2B8
WARRANTY
WARRANTY
These warranties are subject to the following conditions and limitations:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising