07.09145 OM 500BW Sprayer 4-04

07.09145 OM 500BW Sprayer 4-04
TRAILER SPRAYER
MODEL: 500 BW
OPERATOR'S MANUAL
DO NOT OPERATE THIS EQUIPMENT UNTIL THIS
MANUAL HAS BEEN READ AND UNDERSTOOD.
Part Number: 07.09145D
November 2007
MILLER-ST.NAZIANZ,INC.
P.O. BOX 127
ST. NAZIANZ, WI 54232
920/773-2121
FAX:920/773-1200
INTRODUCTION
This Operator's Manual is provided to acquaint the operator with the safety and operation of the Miller
Sprayer. Complete Assembly, Operation, Lubrication and Maintenance procedures are provided. Following the recommended procedures will help you achieve many years of dependable service.
This manual is considered part of your machine and should remain with the machine at all times.
Make sure the operator reads and understands the manual before placing the sprayer into operation.
Failure to follow the recommended procedures may result in injury and equipment damage, and could void
the warranty.
MACHINE SERIAL NUMBER
The machine serial number is located on the left side of the pump mount shield. For your convenience refer
to this number and your product model number when requiring service or parts information. Record the
machine serial number, model number, date of purchase and dealership name in the space provided below.
Date Purchased
Model No.
Serial No.
Dealership
Right and Left Hand sides are determined from a position standing at the rear of the sprayer looking toward
the hitch.
This Operator's Manual uses the term "Tractors" when identifying the power source for the sprayer.
The Delivery and Warranty Registration Card found in the front of this manual must be completed and signed
to validate your warranty protection. You must read and understand the places where you attest to having
received instructions as to care, adjustments, safe operation and applicable warranty policy. The terms and
conditions of the warranty are specified on the rear cover of this manual.
WARNING
SOME PHOTOGRAPHS USED HEREIN MAY SHOW DOORS, GUARDS
AND SHIELDS OPENED OR REMOVED. BE SURE THAT ALL DOORS,
GUARDS AND SHIELDS ARE FASTENED IN THEIR PROPER POSITION
BEFORE MACHINE IS OPERATED!
Table Of Contents
TRAILER SPRAYER ...................................................................................................................................................................................... 2
Pre-Delivery Check List ......................................................................................................................................................................... 2
Delivery Check List ................................................................................................................................................................................ 2
SAFETY PRECAUTIONS .............................................................................................................................................................................. 3
Power Source Shutdown Procedure ...................................................................................................................................................... 3
Implement Safety .................................................................................................................................................................................... 4
Chemical Safety ...................................................................................................................................................................................... 5
SAFETY DECALS .......................................................................................................................................................................................... 6
Reflective Decals .................................................................................................................................................................................. 10
SPRAYER SETUP AND ASSEMBLY .......................................................................................................................................................... 11
Wheel Spacing ...................................................................................................................................................................................... 11
Implement Driveline (PTO Drive Pumps Only) .................................................................................................................................... 12
HITCHING SPRAYER TO TRACTOR ......................................................................................................................................................... 13
Hitching .................................................................................................................................................................................................. 13
Hydraulic Drive Sprayer Pump Hose Hook Up (Optional) ................................................................................................................. 16
Control Box Installation ......................................................................................................................................................................... 16
Electric Sprayer Controls ..................................................................................................................................................................... 17
Hydraulic Hose Connections - Boom Control ...................................................................................................................................... 18
Sprayer Accessories ............................................................................................................................................................................ 20
UNHITCHING SPRAYER FROM TRACTOR ............................................................................................................................................. 20
Unhitching ............................................................................................................................................................................................. 20
TRANSPORTING SPRAYER ...................................................................................................................................................................... 22
SPRAYER ACCESSORIES .......................................................................................................................................................................... 23
Foam Marker Switch Box ..................................................................................................................................................................... 23
Fence Line Kit (Right Side, Left Side or Both) ...................................................................................................................................... 23
In-Cab Electric 50 Gallon Rinse System ............................................................................................................................................. 23
OPERATION ................................................................................................................................................................................................. 24
General Information .............................................................................................................................................................................. 24
Tip Selection .......................................................................................................................................................................................... 26
Spray Tip Wear ..................................................................................................................................................................................... 27
Air Induction Spray Tips (Greenleaf Turbo Drop Nozzles) ................................................................................................................. 28
Air Induction Spray Tips (Greenleaf Turbo Drop Nozzles) ................................................................................................................. 31
TeeJet Air Induction Spray Tips ........................................................................................................................................................... 34
TeeJet Application Rates in Gallons Per Acre ..................................................................................................................................... 35
TeeJet FloodJet Wide Angle Flat Spray Tips ....................................................................................................................................... 41
Sprayer Controls ................................................................................................................................................................................... 42
Standard Primary Filter ......................................................................................................................................................................... 46
Self Cleaning Filter (Optional) ............................................................................................................................................................... 46
Filling The Product Tank ........................................................................................................................................................................ 47
Priming The Sprayer ............................................................................................................................................................................. 50
Calibrating The Sprayer ........................................................................................................................................................................ 52
Tank Tie Down Straps .......................................................................................................................................................................... 53
Chemical Inductor (Optional) ............................................................................................................................................................... 55
Hand Rinse Gun for Chemical Inductor (Optional) ............................................................................................................................. 58
Personal Fresh Water Tank .................................................................................................................................................................. 60
External Sight Gauge (Optional) .......................................................................................................................................................... 60
Rinse Tank Flush System (Optional) ................................................................................................................................................... 61
Cleaning The Sprayer ........................................................................................................................................................................... 66
Hydraulic Boom Operation ................................................................................................................................................................... 70
LUBRICATION ............................................................................................................................................................................................. 73
Daily Lubrication Interval ...................................................................................................................................................................... 73
Weekly Lubrication Interval .................................................................................................................................................................. 74
200 Hour Lubrication Interval ............................................................................................................................................................... 77
MAINTENANCE ........................................................................................................................................................................................... 77
General .................................................................................................................................................................................................. 77
Fasteners .............................................................................................................................................................................................. 77
Tire Pressure ........................................................................................................................................................................................ 77
Filters ..................................................................................................................................................................................................... 77
Sprayer Tips .......................................................................................................................................................................................... 78
STORING AND WINTERIZING ................................................................................................................................................................... 78
BOOM ADJUSTMENTS .............................................................................................................................................................................. 80
HC Boom Only ...................................................................................................................................................................................... 80
EF & EFT Boom Only ........................................................................................................................................................................... 81
TROUBLESHOOTING GUIDES ................................................................................................................................................................. 83
TORQUE SPECIFICATIONS ....................................................................................................................................................................... 86
OPTIONAL ACCESSORIES ....................................................................................................................................................................... 88
In Line Filter Kit ...................................................................................................................................................................................... 88
Fence Line Kit(s) ................................................................................................................................................................................... 89
1
Trailer Sprayer
Pre-Delivery Check List
Delivery Check List
After the Miller Trailer Sprayer has been completely set-up,
the following inspections MUST be made before delivering
it to the customer. Check off each item after prescribed
action is taken.
The following check list is an important reminder of
valuable information that MUST be passed on to the
customer at the time the unit is delivered. Check off
each item as you explain it to the customer.
ˆ NO parts on the unit have been damaged in shipment.
Check for such things as dents and loose or missing
parts; correct or replace components as required.
ˆ Sprayers with power take off (PTO) driven pumps
must have the tractor drawbar adjusted per instructions on page 12.
ˆ Verify correct nozzle spacing.
ˆ Make sure customers know how to connect hydraulic
pumps on sprayers that are equipped for tractor
hydraulics.
ˆ Adjust axles per customer's wheel spacing
request.
ˆ Install electric control box per instructions in separate
control box manual.
ˆ If applicable, sprayer has the correct hydraulically
driven centrifugal pump for the customer's tractor
hydraulics.
ˆ Give the customer this operator’s manual. Instruct
them to be sure to read and completely understand its
contents before attempting to operate the unit.
ˆ Inflate tires to recommended pressure as described
in the Maintenance Section of the Operator Manual.
ˆ Tighten wheel nuts to correct torque (150 ft lb).
ˆ Give the customer the Agricultural Implement Driveline safety manual (907228). Instruct the customer
to be sure to read and completely understand its
contents before attempting to operate the unit.
ˆ Make sure all bolts and other fasteners are
tightened or adjusted properly.
ˆ As applicable, the Cylinders, Hoses and Fittings are
NOT damaged, leaking or loosely connected.
ˆ Explain the warranty.
ˆ Rotating PTO Shields turn freely.
ˆ Explain that regular lubrication and proper adjustments are required for continued proper operation
and long life. Review the maintenance section of this
manual with the customer.
ˆ Lubricate grease fittings.
ˆ Safety decals are in place and legible.
Hook the sprayer to the appropriate RPM tractor and
test run it while checking that proper operation is
exhibited by all components.
ˆ Complete the dealer and warranty registration card.
Have the customer sign it and return it to Miller-St.
Nazianz.
Check that:
ˆ Partially fill tank with water, and operate sprayer to
inspect fittings and hose connections for leaks.
ˆ Included with this manual are separate operator/
installation manuals for some components. Be sure
to read and completely understand the contents of
these before operating the sprayer.
ˆ With water in tank, be sure tank bands are tight.
ˆ All accessories function correctly.
ˆ Transport lights operate properly.
I acknowledge that the above points were reviewed with
me at the time of delivery.
ˆ Hoses secured and not in contact with any moving
parts.
ˆ Hydraulic systems operate properly.
_____________________________________________
_____________________________________________
Dealership's Name
Customer's Signature
_____________________________________________
_____________________________________________
Dealer Representative’s Name
Date Delivered
_____________________________________________
Date Checklist Filled Out
(Customer Copy)
_____________________________________________
Model Number.
Serial Number.
2
Trailer Sprayer
Pre-Delivery Check List
Delivery Check List
After the Miller Trailer Sprayer has been completely set-up,
the following inspections MUST be made before delivering
it to the customer. Check off each item after prescribed
action is taken.
The following check list is an important reminder of
valuable information that MUST be passed on to the
customer at the time the unit is delivered. Check off
each item as you explain it to the customer.
ˆ NO parts on the unit have been damaged in shipment.
Check for such things as dents and loose or missing
parts; correct or replace components as required.
ˆ Verify correct nozzle spacing.
ˆ Adjust axles per customer's wheel spacing
request.
ˆ If applicable, sprayer has the correct hydraulically
driven centrifugal pump for the customer's tractor
hydraulics.
ˆ Inflate tires to recommended pressure as described
in the Maintenance Section of the Operator Manual.
ˆ Tighten wheel nuts to correct torque (150 ft lb).
ˆ Make sure all bolts and other fasteners are
tightened or adjusted properly.
ˆ As applicable, the Cylinders, Hoses and Fittings are
NOT damaged, leaking or loosely connected.
ˆ Rotating PTO Shields turn freely.
ˆ Lubricate grease fittings.
ˆ Safety decals are in place and legible.
ˆ Sprayers with power take off (PTO) driven pumps
must have the tractor drawbar adjusted per instructions on page 12.
ˆ Make sure customers know how to connect hydraulic
pumps on sprayers that are equipped for tractor
hydraulics.
ˆ Install electric control box per instructions in separate
control box manual.
ˆ Give the customer this operator’s manual. Instruct
them to be sure to read and completely understand its
contents before attempting to operate the unit.
ˆ Give the customer the Agricultural Implement Driveline safety manual (907228). Instruct the customer
to be sure to read and completely understand its
contents before attempting to operate the unit.
ˆ Explain the warranty.
ˆ Explain that regular lubrication and proper adjustments are required for continued proper operation
and long life. Review the maintenance section of this
manual with the customer.
Hook the sprayer to the appropriate RPM tractor and
test run it while checking that proper operation is
exhibited by all components.
ˆ Complete the dealer and warranty registration card.
Have the customer sign it and return it to Miller-St.
Nazianz.
Check that:
ˆ Partially fill tank with water, and operate sprayer to
inspect fittings and hose connections for leaks.
ˆ Included with this manual are separate operator/
installation manuals for some components. Be sure
to read and completely understand the contents of
these before operating the sprayer.
ˆ With water in tank, be sure tank bands are tight.
ˆ All accessories function correctly.
ˆ Transport lights operate properly.
ˆ Hoses secured and not in contact with any moving
parts.
I acknowledge that the above points were reviewed with
me at the time of delivery.
ˆ Hydraulic systems operate properly.
_____________________________________________
_____________________________________________
Dealership's Name
Customer's Signature
_____________________________________________
Dealer Representative’s Name
_____________________________________________
Date Delivered
_____________________________________________
Date Checklist Filled Out
(Dealer Copy)
_____________________________________________
Model Number.
Serial Number.
Safety Precautions
This symbol is used to call your attention to instructions concerning your
personal safety. Be sure to observe and follow these instructions. Take time
to be careful!
DANGER
“DANGER” indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
“WARNING” indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
“CAUTION” indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury. It may also alert against
unsafe practices.
BEFORE you attempt to operate this machine, read and study the following safety information. In addition, MAKE SURE that every individual who operates or works with this equipment, whether family member or employee, is familiar with these safety precautions. MillerSt. Nazianz provides guards for exposed moving parts for the operator’s protection; however, some areas cannot be guarded or shielded in order to assure proper operation. The
OPERATOR’S MANUAL AND DECALS on the machine itself warn you of dangers and
SHOULD BE READ AND OBSERVED CLOSELY.
Power Source Shutdown Procedure
Before cleaning, unclogging, adjusting, lubricating or servicing this machine:
1.
2.
3.
4.
5.
Disengage the tractor PTO.
Deactivate tractor hydraulic controls.
Shut off the tractor engine, remove the starter key and take it with you.
Wait for all machine motion to stop.
Remove the telescoping PTO driveline and ALL power connections from
the tractor.
Failure to follow these precautions could result in death or serious injury.
3
Safety Precautions, continued
Implement Safety
Some photographs used herein may show doors, guards and shields opened or removed. BE
SURE that all doors, guards and shields are fastened in their proper position before machine is
operated.
Know how to stop sprayer operation BEFORE starting it.
BE ALERT for people and/or animals in front of or around machine, when about to start
machine.
KEEP hands, feet and clothing away from PTO when in operation!
DO NOT wear loose or baggy clothing when operating this unit!
DO NOT allow people other than a qualified operator near the unit!
DO NOT allow minors to be near the machine unless properly supervised.
KEEP riders off sprayer.
DO NOT unclog, adjust, lubricate or service your sprayer until you disengage the tractor PTO
and shut off the tractor engine. Failure to follow this procedure may result in serious bodily
injury!
AVOID high pressure fluids. Escaping fluid under pressure can penetrate skin causing serious
injury.
DO NOT exceed a maximum towing speed of 20 MPH (32 KPH) while transporting the sprayer.
REDUCE speed on rough or hilly ground.
BE EXTRA careful when going through fence gates or nearing confined quarters.
ALWAYS follow state and local regulations regarding use of a safety chain, slow moving vehicle
signs and transport lighting, when towing farm equipment on public highways.
ALWAYS engage the tractor parking brake before dismounting.
BE SURE the hitch jack locking pin is completely engaged and that the machine is properly
blocked and prevented from rolling BEFORE disconnecting the sprayer from the tractor.
ALWAYS securely block sprayer up when working under sprayer.
DO NOT stand between tractor and sprayer when hitching or unhitching sprayer unless engine
is stopped and parking brake is engaged.
4
Implement Safety, continued
KEEP ALL personnel at a safe distance when folding or unfolding boom.
KEEP all persons away from sprayer and boom while in operation.
KEEP clear of hydraulically controlled booms. Booms may move suddenly, without warning.
AVOID sudden turns when transporting sprayer. Slow tractor before turning.
BE AWARE of sprayer width and boom swing to avoid hitting other objects or personnel.
ALWAYS shut off remote hydraulic supply and relieve pressure before disconnecting.
Provide adequate clearance in all directions when folding or unfolding boom.
KEEP clear of ALL electrical power lines when operating sprayer or when folding or unfolding
booms.
Chemical Safety
Handle ALL agricultural chemicals with care. Use chemicals ONLY as directed on the
manufacturer’s warning label.
WEAR protective clothing (such as goggles, rubber or chemical resistant gloves and respirator)
while handling chemicals.
KEEP protective clothing clean and in good condition. Discard if damaged.
ALWAYS wash hands and face thoroughly with soap and clean water after handling chemicals.
NEVER eat, smoke, drink or put hands to mouth before washing.
Know the phone number and location of the nearest poison control center.
KEEP a list of all chemicals used and the chemical manufacturer’s names.
5
Safety Decals
The decals are for your protection. If your safety decals are not readable or are missing,
contact your dealer for replacements.
“Danger, Rotating
Driveline” decal
(Part No. 329594B2).
“Shield Missing” decal
(Part No. 331639B2).
This decal is mounted on the
driveline and is visible only if
the plastic shield is removed.
WILL
“Danger, Rotating Driveline” decal
(Part No. 16.20177).
This decal is on the guard behind the
pump pulley guard
6
Safety Decals, continued
Decal - Hydraulic Fluid
Pressure
(Part No. 21.09024)
Decal - Before Operating
(Part No. 16.20178)
Agricultural Chemicals
(Part No. 07.05527)
7
Safety Decals, continued
Decal - Foot Crushing Hazard
(Part No. 17.01155)
Decal - 540 RPM
(Part No. 340248B1)
WARNING
Decal - Fresh Water Tank
(Part No. 07.09573)
Avoid bodily injuries from hydraulic oil•
and gas under pressure.
Before removing or charging accumulator
1. Start engine.
2. Relieve the pressure in the circuit by •
collapsing the cylinder and holding•
the valve open for 5 seconds.
3. Stop the engine.
Use only DRY NITROGEN for •
charging accumulator.
12.09044
Decal - Accumulator Pressure
(Part No. 21.09044)
8
Safety Decals, continued
Decal - Pinch Point Qty 2
(Part No. 21.09025)
Decal - Hydraulic Fluid
Pressure
(Part No. 21.09024)
9
Safety Decals, continued
Reflective Decals
Yellow Reflector (Qty. 2)
(Part No. 907220) Not
Shown, One On Each
Side Of Hitch
Yellow Reflector (Qty. 2)
Left Side Shown
(Part No. 907220)
SMV Emblem
(Part No. 907224)
Red Reflector (Qty.2)
Left Side Shown
(Part No. 907219)
Yellow Reflector (Qty. 2)
(Part No. 907220)
10
Sprayer Setup And Assembly
Wheel Spacing
Wheel spacing can be adjusted from 62 inches (minimum) to 80 inches (maximum).
To change wheel spacing proceed as follows:
DANGER
Sprayer can fall during wheel spacing adjustment and crush person working
under sprayer. Death or serious injury will result. Support the sprayer securely when adjusting wheel spacing.
1.
Hitch sprayer to tractor (refer to the “Hitching” section on page 13 of this manual). Place
chocks or blocks in front of and behind wheel on opposite side of wheel to be adjusted.
2.
Measure and mark center of sprayer frame to assure equal spacing of wheels from sprayer
centerline.
3.
Place a hydraulic or screw jack under the sprayer frame behind the axle on the same side as
the wheel to be adjusted. Jack up the sprayer high enough to raise the wheel from the ground.
4.
Block the sprayer frame to keep sprayer from dropping if jack should fail or lose pressure.
5.
Loosen the nuts on the U-bolts securing the wheel and hub assembly to the sprayer frame.
6.
Slide the wheel and hub assembly in or out to the desired distance. Measure from the
centerline of the sprayer to the centerline of the tire. DO NOT exceed the minimum 62 inch or
maximum 80 inch distances.
7.
Tighten the hex nuts on the U-bolts.
8.
Lower the wheel to the ground.
9.
Repeat steps 3 through 8 for the wheel assembly on the other side of the sprayer.
U-Bolts
U-Bolts
Tank Removed For
Clarity
11
Implement Driveline (PTO Drive Pumps Only)
WARNING
Before working on PTO shaft or connecting or disconnecting it, STOP tractor,
apply the parking brake, and make sure that the tractor motor has stopped
turning.
The Miller Sprayer is designed to be used with a tractor having a 540 RPM PTO unless your
sprayer has a 1000 RPM centrifugal pump (Optional).
Adjust the tractor drawbar so the distance from the end of the PTO shaft to the center of the drawbar hitch pin hole (Dimension A) is 14.00" for 540 RPM PTO or 16.00" for 1000 RPM PTO.
NOTE: If the hitch pin hole is located well behind the tractor tires, the operator can make a turn
sharp enough to damage the driveline.
Dimension A
Tractor PTO
Shaft
Tractor Drawbar
12
Hitching Sprayer To Tractor
CAUTION
DO NOT stand between the tractor and sprayer when hitching or unhitching
the sprayer unless tractor engine is STOPPED and parking brake is applied.
Hitching
1.
Align the tractor drawbar with the sprayer clevis hitch.
2.
Shut down and lockout the power source. Refer to “Power Source Shutdown Procedure” on
Page 3 of this manual. Follow these procedures to correctly lockout the power source.
3.
If necessary, adjust the position of the hitch so that the sprayer is as level as possible when
hitched to the tractor. Adjust the hitch as follows:
a. Remove the four bolts securing the hitch to the flanges on the sprayer tongue.
b. Raise or lower the hitch or rotate the hitch 180° to a position that will ensure that the
sprayer is as level as possible.
c. Insert all four bolts through the flanges on the sprayer tongue and the hitch. Tighten securely.
Sprayer Tongue
Hitch
Bolts
4.
Remove the hitch pin and clip from their storage positions.
5.
Install the hitch pin. Insert the clip through the side of the hitch pin to lock in place.
6.
Turn the leveling crank on the jack stand until the jack no longer touches the ground.
NOTE: Safety chains are available for your sprayer by ordering Part No. 329946B91 from your
Miller dealer.
13
7.
Store the jack during operation.
a. Remove the pin and clip from the jack mount on the sprayer hitch.
b. Remove the jack from the mount.
Pin and Clip
Jack In Hitch/Unhitch
Position
c. Position the jack onto the storage mount on the sprayer frame.
d. Secure in place with the pin and clip.
Pin and Clip
Jack In Stored Position
Important: Always secure the jack in the storage position before beginning any operation or
transport of the sprayer. Damage to the jack can result if jack is not stored during operation
or transport.
14
WARNING
Connect 540 RPM sprayer pumps ONLY to 540 RPM tractor PTO output shafts.
Connect Optional 1000 RPM sprayer pumps ONLY to 1000 RPM tractor PTO
output shafts.
8.
Pull the collar on the tractor end of the driveline to the rear (toward the sprayer), and slide the
driveline onto the tractor’s PTO output shaft as far as possible.
9.
Release the collar. Pull the driveline to the rear (toward the sprayer) until the collar snaps into
the locked position, and the driveline cannot be moved forward or backward.
WARNING
Be certain that the driveline is securely attached to the PTO shaft on the power
source. Install all shield system components before beginning operation.
15
Hydraulic Drive Sprayer Pump Hose Hook Up (Optional)
Hydraulic Hose Hook Up:
WARNING
Hydraulic oil under pressure can spray into eyes and cause physical injury.
Follow tractor operator manual instructions for shutting off hydraulic supply
and relieving hydraulic pressure before connecting or disconnecting hydraulic
hoses.
1.
Assemble the sprayer hydraulic pump hoses to the tractor hydraulic couplers.
IMPORTANT: Assemble the hoses to the tractor, but DO NOT activate hydraulics until the
pump has been properly primed.
2.
Place the tractor hydraulic control lever in the position next to the float position. The pump
should operate. If the pump does not operate, place the tractor hydraulic control lever in the
float position.
3.
Disconnect and reverse the sprayer hose connections at the tractor. The pump should operate.
IMPORTANT: Always use the float position to STOP the hydraulic sprayer pump.
Note: If sprayer is being hitched to the tractor for the first time, charge the sprayer hydraulic system
with oil.
IMPORTANT: The storage slots for the hydraulic hoses should ONLY be used when sprayer
is disconnected from the tractor and being stored. Hydraulic hoses MUST always be connected to tractor during transport of sprayer.
Control Box Installation
Electrical Connections To Tractor
When connecting the electrical control boxes to the tractor, it is recommended that you purchase a
wiring harness pigtail adaptor from your tractor dealer or your local Miller dealer.
Examples of these pigtails are:
Miller Part No. 21.21624, John Deere Part No. RE67013 or Case-IH Part No. 187103A1.
Be sure to ONLY connect to tractors with a 12 Volt Positive electrical system.
16
Electric Sprayer Controls
Note: Refer to the separate control box owner’s manual for detailed installation instructions.
1.
Turn OFF all switches.
2.
Install control box in the tractor cab in a location where it can be used easily and is readily
visible.
3.
Determine best routing for control cable and pressure tube. Be sure the cables and/or tubes
DO NOT interfere with any moving parts on tractor or sprayer.
4.
Install Mounting bracket
5.
Make tractor connections for power input, ground and pressure tubing if so equipped.
TeeJet Controller (Standard):
a. Connect the 2 RED wires to the 12 volt power source (positive).
b. Connect the 2 BLACK wires to a ground point on the tractor (negative).
c. Connect the single BLUE wire to the tractor headlight system. The BLUE wire powers the
light in the pressure gauge and does not turn OFF with the control box switch. DO NOT
connect directly to a power source that does not disconnect when the tractor is shut OFF.
d. Using the pressure tube coupler and fittings, connect the tube in the control wiring harness
to the tube in the extension wiring harness. Install the coupler outside the tractor cab in
case it would leak.
A gauge isolator (Part No. 07.17961) is available to use in place of the pressure tube
coupler. If it is installed outside the tractor cab, it prevents chemicals from entering the
tractor cab. It also protects the control box
gauge when liquid nitrogen is sprayed.
TeeJet Controller (Standard)
Raven Rate Controller (Optional):
a. Connect the RED wire directly to the
battery (12 volt - positive). DO NOT connect to a remote power source.
b. Connect the WHITE wire directly to the
battery (12 volt - ground). DO NOT connect to a remote ground source.
c. The rate controller is normally pre-programmed from Miller for your sprayer, but
you should verify that the programming
matches your sprayer specifications. It is
very important that the radar gun input
number is correct - refer to the Raven
owner’s manual.
6.
Complete the final assembly and make the final
connections. Test system to make sure it is
working properly.
17
RAVEN Rate Controller (Optional)
Hydraulic Hose Connections - Boom Control
There are three types of booms available for your sprayer.
•
EF Hydraulic fold with boom widths of: 38 ft, 45 ft, 48 ft and 51 ft.
•
EFT Hydraulic fold & wing tilt with boom widths of: 38 ft, 45 ft, 48 ft and 51 ft.
•
HC Hydraulic fold with boom widths of: 45 ft and 51 ft.
WARNING
Hydraulic oil under pressure can spray into eyes and cause physical injury.
Follow tractor operator manual instructions for shutting off hydraulic supply
and relieving hydraulic pressure before connecting or disconnecting hydraulic
hoses.
EF &EFT Boom Hydraulic Hose Connections
1.
The EF & EFT boom utilizes three separate hydraulic hoses which must be connected to the
appropriate couplers on the tractor. All three male tips are an ASAE standard tip (Pioneer).
•
The single hose will operate the entire boom UP or DOWN & for EFT boom with switch
activated will tilt left wing UP or DOWN.
•
The pair of hoses will operate the fold IN or OUT & for EFT boom with switch activated will
tilt right wing UP or DOWN
2.
The hoses on the sprayer are maked with colored tie wraps to identify the hoses for proper
connection to the tractor. The pair of hoses for the fold IN or OUT will have one color and the
boom UP or DOWN will be another color.
3.
There is an extra set of the colored tie wraps shipped with your sprayer. Attach these tie
wraps to the proper tractor hydraulic couplers to aid in the correct reattaching of the sprayer
hydraulic hoses.
Note: If sprayer is being hitched to the tractor for the first time, charge the sprayer hydraulic system
with oil.
IMPORTANT: The storage slots for the hydraulic hoses should ONLY be used when sprayer
is disconnected from the tractor and being stored. Hydraulic hoses MUST always be connected to tractor during transport of sprayer.
EFT Boom Electrical Connections
There are three wires that are to be connected to the tractor.
1.
Connect the two RED wires to the positive (+) 12 volt power source of the tractor. The RED
wires can be connected directly to the battery or to an auxiliary connection such as the fuse
block.
2.
Connect the WHITE wire to the negative (-) ground source of the tractor. The WHITE wire can
be connected directly to the negative battery or to an auxiliary connection as long as a good
ground is maintained.
18
HC Boom Hydraulic Hose and Electrical Connections
Your sprayer has been shipped from the factory set-up for use with a tractor that has “Open Center”
Hydraulics. Determine if your tractor has this type of hydraulics.
Connect sprayer hydraulic hoses to the tractor hydraulic system. When the HC boom is in use ,
the hydraulic valve on the tractor MUST be locked open to assure a constant supply of oil to the
cylinder valve control bank located at the back of the sprayer.
HC Boom Electrical Connections
There are two wires that are to be connected to the tractor.
1.
Connect the RED wire to the positive (+) 12 volt power source of the tractor. The RED wire
can be connected directly to the battery or to an auxiliary connection such as the fuse block.
2.
Connect the WHITE wire to the negative (-) ground source of the tractor. The WHITE wire can
be connected directly to the negative battery or to an auxiliary connection as long as a good
ground is maintained.
If your tractor has “Closed Center” Hydraulics, turn the flow rate on your tractor hydraulic system
down to 5 to 6 GPM and try the sprayer boom functions. If the sprayer functions are not satisfactory, the valve block located at the rear of the boom can be altered to operate with “Closed Center”
Hydraulic systems.
To change from “Open Center” Hydraulic system set-up to “Closed Center” Hydraulics:
1.
Locate the valve block at the rear of your sprayer on the rear tower.
2.
Locate the lower left solenoid cartridge on the face of the valve block.
3.
Remove the wire coil and open center bypass valve from the valve block. Insert the hex plug,
shipped with your sprayer into the valve block and tighten.
4.
Your sprayer is now set-up to be used with “Closed Center” Hydraulics.
Note: If sprayer is being hitched to the tractor for the first time, charge the sprayer hydraulic system
with oil.
IMPORTANT: The storage slots for the hydraulic hoses should ONLY be used when sprayer
is disconnected from the tractor and being stored. Hydraulic hoses MUST always be connected to tractor during transport of sprayer.
Valve Block
Replace This Wire Coil and
Open Center Bypass Valve
With Plug For Closed
Center Hydraulics
19
Sprayer Accessories
Make all required electrical connections for sprayer accessories. Refer to the “Accessories” section of this manual for proper instructions on electrical connections.
Unhitching Sprayer From Tractor
Unhitching
CAUTION
DO NOT stand between the tractor and sprayer when hitching or unhitching
the sprayer unless tractor engine is STOPPED and parking brake is applied.
WARNING
Before disconnecting the PTO shaft, make sure that the tractor motor has
stopped turning before getting off the tractor.
WARNING
Hydraulic oil under pressure can spray into eyes and cause physical injury.
Follow tractor operator manual instructions for shutting off hydraulic supply
and relieving hydraulic pressure on sprayers with remote hydraulic controls.
1.
Park sprayer on a firm, level surface. Block both sprayer wheels to prevent any unexpected
movement when the sprayer is unhitched from the tractor,
2.
Shut down and lockout the power source. Refer to “Power Source Shutdown Procedure” on
Page 3 of this manual. Follow these procedures to correctly lockout the power source.
3.
Remove the pin and clip from the jack mount and remove the jack from the stored position on
the sprayer frame.
Pin and Clip
Jack In Stored Position
20
4.
Position the jack onto the mounting hub on the sprayer hitch. Align the holes in the jack with
the holes in the mount and insert the pin and clip to secure the jack in place.
5.
Turn the leveling crank on the jack until the hitch begins to rise up off the tractor drawbar.
Pin and Clip
Leveling Crank
Jack In Hitch/Unhitch
Position
6.
Relieve the pressure in the hydraulic system. Uncouple the hoses from the tractor remotes.
7.
Disconnect electrical connections on all sprayer accessories.
8.
Pull collar on tractor end of implement driveline to the rear. Slide the driveline off the tractor
output shaft.
9.
Remove the hitch pin and clip. Reinstall the hitch pin and clip in the storage position.
Collar On
Tractor End Of
Driveline
Hitch Pin
IMPORTANT: The storage slots for the hydraulic hoses should ONLY be used when sprayer
is disconnected from the tractor and being stored. Hydraulic hoses MUST always be connected to tractor during transport of sprayer.
21
Transporting Sprayer
IMPORTANT: Observe the safety precautions when transporting the sprayer to another
location:
1.
DO NOT allow anyone to ride on sprayer or tractor.
2.
DO NOT transport the sprayer unless the booms are fully folded and boom is securely placed
in the boom transport rests.
3.
AVOID sudden turns which may reduce operator control of the tractor or cause sprayer to tip.
Sprayers tend to be top heavy when tank is filled and wheels are set at 62 inches.
4.
ALWAYS be aware of the location of the ends of the booms in order to avoid collisions with
stationary or moving objects.
IMPORTANT: NEVER exceed the maximum towing speed of 20 MPH (32 KMH). Reduce
speed when turning or traveling on rough or hilly terrain.
Transport Lighting
The sprayer is equipped with transport lighting for transporting the sprayer on public highways. The
light cord supplied with the sprayer has a standard seven prong plug. Contact your tractor dealer if
your tractor does not have the appropriate receptacle.
SMV Emblem and Reflectors
The sprayer is provided with reflective strips and a slow moving vehicle (SMV) emblem.
Unless prohibited, always use a SMV emblem.
Safety Chain
Sprayers can be equipped with a safety chain (Part No. 329946B91) for travel on public highways.
Contact your dealer to order. When attaching chain, be sure to allow enough slack for turning.
22
Sprayer Accessories
Listed are the accessories available and the connection instructions if required.
For ease of connecting accessories to your tractor, see your tractor dealer or your local Miller
dealer for an accessory connecting pigtail harness that connects directly to your tractor electrical
system and allows your accessory to be “keyed” to the tractor ignition.
Examples of some of these pigtails are:
Miller Part no. 21.21624, John Deere Part Number RE67013 or Case - IH Part Number 187103A1.
NOTE: If your sprayer is equipped with the HC boom, all connections for these accessories will be
incorporated into the HC control box and wire harness.
The instructions listed are for sprayers with EF booms only.
Foam Marker Switch Box
A foam marking system is an optional accessory. If your sprayer is equipped with a foam marker,
refer to the owner’s manual supplied with the unit for installation instructions.
Connect the foam marker kit as follows:
•
Connect the WHITE wire to the Positive (+) 12 volt power source on your tractor.
•
Connect the BLACK wire to the Negative (-) ground source on your tractor or a good
ground.
Fence Line Kit (Right Side, Left Side or Both)
A fence line kit is an optional accessory. Refer to the “Optional Accessories” section later in this
manual for operation of this accessory.
NOTE: This system is not fused. It is recommended that this system be connected to a fused
power source on the tractor.
Connect the fence line kit as follows:
•
Connect the RED wire to the Positive (+) 12 volt power source on your tractor.
•
Connect the BLACK wire to the Negative (-) ground source on your tractor or a good
ground.
In-Cab Electric 50 Gallon Rinse System
A in-cab electric rinse system is a option for your sprayer. This system requires connection to the
tractor electrical system.
Connect the in-cab rinse system as follows:
•
Connect the RED wire to the Positive (+) 12 volt power source on your tractor.
•
Connect the BLACK wire to the Negative (-) ground source on your tractor or a good
ground.
NOTE: This system is not fused. It is recommended that this system be connected to a fused
power source on the tractor.
23
Operation
Topics covered in this section include the following:
•
Sprayer tip selection
•
Priming and calibrating the sprayer
•
Sprayer control systems
•
Booms and boom operation
A water tank mounted on a trailer, a boom, a pump and a control system are the basic equipment for
all sprayers. However, many variations of this basic equipment are possible depending on the
capacity of the water tank and the type of boom, pump and control systems selected. In addition,
sprayers may also be equipped with various accessories.
NOTE: This section of the manual may include information and procedures for optional accessories
which are not part of your sprayer’s equipment.
General Information
This section includes general information operators will find helpful for cost-effective sprayer operation.
Measuring Travel Speed
Measure a test course in the area to be sprayed or in an area with similar surface conditions. Minimum lengths of 100 and 200 feet are recommended for measuring speeds up to 5 and 10 miles per
hour, respectively. Determine the time required to travel the test course.
To help ensure accuracy, conduct the speed check with a loaded sprayer and select the engine
throttle setting and gear that will be used when spraying. Repeat the above process and average
the times that were measured. Use the following equation or the table to determine ground speed.
Speed
Travel Time Required (seconds)
(mph)
100 Feet
200 Feet
300 Feet
3.0
23
45
68
3.5
20
39
58
4.0
17
34
51
4.5
15
30
45
5.0
14
27
41
6.0
---
23
34
7.0
---
19
29
7.5
---
18
27
8.0
---
17
26
9.0
---
15
23
24
Useful Formulas and Conversions
GPA=
Application rate in gallon per acre
GPM=
Flow rate in gallons per minute
S=
Speed in miles per hour
W=
Nozzle spacing in inches
Calculate flow rate per nozzle when application rate, speed and nozzle spacing are known:
GPM (per Nozzle) = GPA x S x W
5940
Calculate application rate when nozzle spacing, speed and flow rate are known:
GPA = 5940 x GPM
SxW
Calculate speed when flow rate, application rate and nozzle spacing are known:
S = 5940 x GPM
GPA x W
Convert speed from feet per second to miles per hour:
S = Feet per second x 0.682
Spraying Solutions Other Than Water
Since all the tabulations are based on spraying water, which weighs 8.34 lbs. per US gallon, conversion factors must be used when spraying solutions which are heavier or lighter than water. To
determine the proper size nozzle for the solution to be sprayed, first multiply the desired GPM or
GPA of solution by the water rate conversion factor. Then use the new converted GPM or GPA
rate to select the proper size nozzle.
Example:
Desired application is 20 GPA of 28%N. Determine the correct nozzle size as follows:
GPA (solution) x Conversion factor = GPA (from table)
20 GPA (28%) x 1.13 = 22.6 GPA (water)
The applicator should choose a nozzle size that will supply 22.6 GPA of water at the desired pressure.
Weight Of Solution
Specific Gravity
Conversion Factors
8.34 lbs per gallon - Water
1.0
1.0
10.65 lbs per gallon - 28% Nitrogen
1.28
1.13
11.0 lbs per gallon - 32% Nitrogen
1.32
1.15
25
Tip Selection
Proper application of agricultural chemicals is essential to good performance. Applying the correct
amount and effectively covering the target are key factors in proper application. Too often, poor
weed, disease, or insect control can be traced to problems with spray distribution along the boom.
Spray distribution refers to the uniformity of spray coverage across the boom swath. The goal in
broadcast spraying is even (uniform) spray distribution. Factors affecting spray distribution include
nozzle type, spray pattern angle, nozzle spacing and boom height. When selecting nozzles to be
used on a boom for broadcast application, finding the correct combination of these factors is important. The nozzle spray angle and the height of the boom will determine the overlap between adjacent tips, which is critical to uniform distribution.
Unless otherwise specified at the time of manufacture, your sprayer is equipped with flat fan spray
nozzles having the following characteristics:
•
Volume: approximately 20 GPA at 30 psi at 5 mph
•
Spray angle: 110 degrees
•
Nozzle spacing: 20 inches
If you want to change the application rate or the type of nozzle, the tables on the following pages
provide the information needed to help you choose the right nozzle for common applications. (Refer
to the product catalog for more specific information).
IMPORTANT: Your chemical supplier can give you accurate information about the recommended chemical mixture and the application rate. Check with your supplier before you
select a different tip.
You must know the following information to use the nozzle selection tables:
•
The type of nozzle (flat fan, cone, or flood)
•
The spraying pressure you will be using (psi)
•
The application rate (GPA)
•
The nozzle spacing (in inches)
•
The operating speed in miles per hour
26
Spray Tip Wear
27
Air Induction Spray Tips (Greenleaf Turbo Drop Nozzles)
15 Inch Nozzle Spacing
Medium Pressure TurboDrop® XL Nozzle (TDXL, TDCXL)
Optimal pressure range is 30-90 psi. Targeting 60 psi operating pressure will allow for greater
changes in speed and pressure. Max pressure is 120 psi. Higher pressures are recommended for
contact pesticides (60-120 psi).
At lower pressures, the spray angle of the exit tip will narrow by approximately 10-15% (making a
110 degree tip essentially a 90-100 degree tip). Make necessary boom height adjustment for desired overlap. (For 20" spacing, a height of 20-36" is recommended.)
Complete
Nozzle #
AM11001
TDXL-11001
TDCXL-11001
50 mesh screen
AM110015
TDXL-110015
TDCXL-110015
50 mesh screen
Liquid
Nozzle
Pressure
Capacity
PSI
GPM
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
120
130
140
150
0.07
0.09
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.17
0.18
0.19
0.19
0.11
0.13
0.15
0.17
0.18
0.20
0.21
0.22
0.24
0.25
0.26
0.26
0.27
0.28
0.29
GALLONS PER ACRE BASED ON 15” NOZZLE SPACING
4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 10 MPH 12 MPH 14 MPH 16 MPH 18 MPH
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.8
18.5
19.2
10.5
12.9
14.8
16.6
18.2
19.6
21.0
22.3
23.5
24.6
25.7
25.7
26.8
27.8
28.7
5.6
6.9
7.9
8.8
9.7
10.5
11.2
11.9
12.5
13.1
13.7
14.3
14.8
15.3
8.4
10.3
11.9
13.3
14.5
15.7
16.8
17.8
18.8
19.7
20.6
20.6
21.4
22.2
23.0
4.7
5.7
6.6
7.4
8.1
8.7
9.3
9.9
10.4
10.9
11.4
11.9
12.3
12.8
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.1
17.8
18.5
19.2
28
4.0
4.9
5.7
6.3
6.9
7.5
8.0
8.5
8.9
9.4
9.8
10.2
10.6
10.9
6.0
7.3
8.5
9.5
10.4
11.2
12.0
12.7
13.4
14.1
14.7
14.7
15.3
15.9
16.4
3.5
4.3
4.9
5.5
6.1
6.5
7.0
7.4
7.8
8.2
8.6
8.9
9.3
9.6
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
12.9
13.4
13.9
14.4
2.8
3.4
4.0
4.4
4.8
5.2
5.6
5.9
6.3
6.6
6.9
7.1
7.4
7.7
4.2
5.1
5.9
6.6
7.3
7.9
8.4
8.9
9.4
9.8
10.3
10.3
10.7
11.1
11.5
2.3
2.9
3.3
3.7
4.0
4.4
4.7
4.9
5.2
5.5
5.7
5.9
6.2
6.4
3.5
4.3
4.9
5.5
6.1
6.5
7.0
7.4
7.8
8.2
8.6
8.6
8.9
9.3
9.6
2.0
2.4
2.8
3.2
3.5
3.7
4.0
4.2
4.5
4.7
4.9
5.1
5.3
5.5
3.0
3.7
4.2
4.7
5.2
5.6
6.0
6.4
6.7
7.0
7.3
7.3
7.6
7.9
8.2
1.7
2.1
2.5
2.8
3.0
3.3
3.5
3.7
3.9
4.1
4.3
4.5
4.6
4.8
2.6
3.2
3.7
4.1
4.5
4.9
5.2
5.6
5.9
6.2
6.4
6.4
6.7
6.9
7.2
1.6
1.9
2.2
2.5
2.7
2.9
3.1
3.3
3.5
3.6
3.8
4.0
4.1
4.3
2.3
2.9
3.3
3.7
4.0
4.4
4.7
4.9
5.2
5.5
5.7
5.7
5.9
6.2
6.4
15 Inch Nozzle Spacing (continued)
Complete
Nozzle #
AM11002
TDXL-11002
TDCXL-11002
50 mesh screen
AM110025
TDXL-110025
TDCXL-110025
50 mesh screen
AM11003
TDXL-11003
TDCXL-11003
50 mesh screen
AM11004
TDXL-11004
TDCXL-11004
24 mesh screen
Liquid
Nozzle
Pressure
Capacity
PSI
GPM
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
0.14
0.17
0.20
0.22
0.24
0.26
0.28
0.30
0.32
0.33
0.35
0.36
0.37
0.39
0.18
0.22
0.25
0.28
0.31
0.33
0.35
0.37
0.40
0.41
0.43
0.45
0.47
0.48
0.21
0.26
0.30
0.34
0.37
0.40
0.42
0.45
0.47
0.50
0.52
0.54
0.56
0.58
0.28
0.35
0.40
0.45
0.49
0.53
0.57
0.60
0.63
0.66
0.69
0.72
0.75
0.77
GALLONS PER ACRE BASED ON 15” NOZZLE SPACING
4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 10 MPH 12 MPH 14 MPH 16 MPH 18 MPH
14.0
17.1
19.8
22.1
24.2
26.2
28.0
29.7
31.3
32.8
34.3
35.7
37.0
38.3
17.5
21.4
24.7
27.7
30.3
32.7
35.0
37.1
39.1
41.0
42.8
44.6
46.3
47.9
21.0
25.7
29.7
33.2
36.3
39.3
42.0
44.5
46.9
49.2
51.4
53.5
55.5
57.5
28.0
34.3
39.6
44.2
48.5
52.3
56.0
59.4
62.6
65.6
68.5
71.3
74.0
76.6
11.2
13.7
15.8
17.7
19.4
20.9
22.4
23.7
25.0
26.2
27.4
28.5
29.6
30.7
14.0
17.1
19.8
22.1
24.2
26.2
28.0
29.7
31.3
32.8
34.3
35.7
37.0
38.3
16.8
20.6
23.7
26.5
29.1
31.4
33.6
35.6
37.5
39.4
41.1
42.8
44.4
46.0
22.4
27.4
31.7
35.4
38.8
41.9
44.8
47.5
50.1
52.5
54.8
57.1
59.2
61.3
9.3
11.4
13.2
14.7
16.2
17.4
18.7
19.8
20.9
21.9
22.8
23.8
24.7
25.5
11.7
14.3
16.5
18.4
20.2
21.8
23.3
24.7
26.1
27.3
28.6
29.7
30.8
31.9
14.0
17.1
19.8
22.1
24.2
26.2
28.0
29.7
31.3
32.8
34.3
35.7
37.0
38.3
18.7
22.8
26.4
29.5
32.3
34.9
37.3
39.6
41.7
43.7
45.7
47.6
49.4
51.1
29
8.0
9.8
11.3
12.6
13.8
15.0
16.0
17.0
17.9
18.7
19.6
20.4
21.2
21.9
10.0
12.2
14.1
15.8
17.3
18.7
20.0
21.2
22.3
23.4
24.5
25.5
26.4
27.4
12.0
14.7
17.0
19.0
20.8
22.4
24.0
25.4
26.8
28.1
29.4
30.6
31.7
32.8
16.0
19.6
22.6
25.3
27.7
29.9
32.0
33.9
35.8
37.5
39.2
40.8
42.3
43.8
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.8
18.5
19.2
8.7
10.7
12.4
13.8
15.1
16.4
17.5
18.5
19.6
20.5
21.4
22.3
23.1
23.9
10.5
12.9
14.8
16.6
18.2
19.6
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.7
14.0
17.1
19.8
22.1
24.2
26.2
28.0
29.7
31.3
32.8
34.3
35.7
37.0
38.3
5.6
6.9
7.9
8.8
9.7
10.5
11.2
11.9
12.5
13.1
13.7
14.3
14.8
15.3
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.8
18.5
19.2
8.4
10.3
11.9
13.3
14.5
15.7
16.8
17.8
18.8
19.7
20.6
21.4
22.2
23.0
11.2
13.7
15.8
17.7
19.4
20.9
22.4
23.7
25.0
26.2
27.4
28.5
29.6
30.7
4.7
5.7
6.6
7.4
8.1
8.7
9.3
9.9
10.4
10.9
11.4
11.9
12.3
12.8
5.8
7.1
8.2
9.2
10.1
10.9
11.7
12.4
13.0
13.7
14.3
14.9
15.4
16.0
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.8
18.5
19.2
9.3
11.4
13.2
14.7
16.2
17.4
18.7
19.8
20.9
21.9
22.8
23.8
24.7
25.5
4.0
4.9
5.7
6.3
6.9
7.5
8.0
8.5
8.9
9.4
9.8
10.2
10.6
10.9
5.0
6.1
7.1
7.9
8.7
9.3
10.0
10.6
11.2
11.7
12.2
12.7
13.2
13.7
6.0
7.3
8.5
9.5
10.4
11.2
12.0
12.7
13.4
14.1
14.7
15.3
15.9
16.4
8.0
9.8
11.3
12.6
13.8
15.0
16.0
17.0
17.9
18.7
19.6
20.4
21.2
21.9
3.5
4.3
4.9
5.5
6.1
6.5
7.0
7.4
7.8
8.2
8.6
8.9
9.3
9.6
4.4
5.4
6.2
6.9
7.6
8.2
8.7
9.3
9.8
10.3
10.7
11.1
11.6
12.0
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
13.4
13.9
14.4
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.8
18.5
19.2
3.1
3.8
4.4
4.9
5.4
5.8
6.2
6.6
7.0
7.3
7.6
7.9
8.2
8.5
3.9
4.8
5.5
6.1
6.7
7.3
7.8
8.2
8.7
9.1
9.5
9.9
10.3
10.6
4.7
5.7
6.6
7.4
8.1
8.7
9.3
9.9
10.4
10.9
11.4
11.9
12.3
12.8
6.2
7.6
8.8
9.8
10.8
11.6
12.4
13.2
13.9
14.6
15.2
15.9
16.5
17.0
15 Inch Nozzle Spacing (continued)
Complete
Nozzle #
AM11005
TDXL-11005
TDCXL-11005
24 mesh screen
AM11006
TDXL-11006
TDCXL-11006
24 mesh screen
TDXL-11008
TDCXL-11008
TDXL-11010
TDCXL-11010
Liquid
Nozzle
Pressure
Capacity
PSI
GPM
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
0.35
0.43
0.50
0.56
0.61
0.66
0.71
0.75
0.79
0.83
0.87
0.90
0.94
0.97
0.42
0.52
0.60
0.67
0.74
0.79
0.85
0.90
0.95
1.00
1.04
1.08
1.12
1.16
0.56
0.69
0.80
0.89
0.98
1.05
1.13
1.20
1.26
1.32
1.38
1.44
1.49
1.54
0.71
0.87
1.00
1.12
1.22
1.32
1.41
1.50
1.58
1.66
1.73
1.80
1.87
1.94
GALLONS PER ACRE BASED ON 15” NOZZLE SPACING
4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 10 MPH 12 MPH 14 MPH 16 MPH 18 MPH
35.0
42.9
49.5
55.4
60.7
65.5
70.0
74.3
78.3
82.1
85.8
89.3
92.7
95.9
42.0
51.5
59.4
66.4
72.8
78.6
84.0
89.1
94.0
98.5
102.9
107.1
111.2
115.1
55.8
68.3
78.9
88.2
96.6
104.4
111.6
118.3
124.7
130.8
136.6
142.2
147.6
152.8
70.0
85.7
98.9
110.6
121.2
130.9
139.9
148.4
156.4
164.1
171.3
178.3
185.1
191.6
28.0
34.3
39.6
44.3
48.5
52.4
56.0
59.4
62.6
65.7
68.6
71.4
74.1
76.7
33.6
41.2
47.5
53.1
58.2
62.9
67.2
71.3
75.2
78.8
82.3
85.7
88.9
92.1
44.6
54.7
63.1
70.6
77.3
83.5
89.3
94.7
99.8
104.7
109.3
113.8
118.1
122.2
56.0
68.5
79.1
88.5
96.9
104.7
111.9
118.7
125.1
131.2
137.1
142.7
148.1
153.3
23.3
28.6
33.0
36.9
40.4
43.7
46.7
49.5
52.2
54.8
57.2
59.5
61.8
63.9
28.0
34.3
39.6
44.3
48.5
52.4
56.0
59.4
62.6
65.7
68.6
71.4
74.1
76.7
37.2
45.5
52.6
58.8
64.4
69.6
74.4
78.9
83.2
87.2
91.1
94.8
98.4
101.8
46.6
57.1
66.0
73.7
80.8
87.2
93.3
98.9
104.3
109.4
114.2
118.9
123.4
127.7
20.0
24.5
28.3
31.6
34.7
37.4
40.0
42.5
44.7
46.9
49.0
51.0
52.9
54.8
24.0
29.4
34.0
38.0
41.6
44.9
48.0
50.9
53.7
56.3
58.8
61.2
63.5
65.8
31.9
39.0
45.1
50.4
55.2
59.6
63.8
67.6
71.3
74.8
78.1
81.3
84.3
87.3
40.0
49.0
56.5
63.2
69.2
74.8
79.9
84.8
89.4
93.7
97.9
101.9
105.8
109.5
30
17.5
21.4
24.8
27.7
30.3
32.8
35.0
37.1
39.2
41.1
42.9
44.6
46.3
48.0
21.0
25.7
29.7
33.2
36.4
39.3
42.0
44.6
47.0
49.3
51.5
53.6
55.6
57.5
27.9
34.2
39.4
44.1
48.3
52.2
55.8
59.2
62.4
65.4
68.3
71.1
73.8
76.4
35.0
42.8
49.5
55.3
60.6
65.4
70.0
74.2
78.2
82.0
85.7
89.2
92.5
95.8
14.0
17.2
19.8
22.1
24.3
26.2
28.0
29.7
31.3
32.9
34.3
35.7
37.1
38.4
16.8
20.6
23.8
26.6
29.1
31.4
33.6
35.7
37.6
39.4
41.2
42.8
44.5
46.0
22.3
27.3
31.6
35.3
38.6
41.7
44.6
47.3
49.9
52.3
54.7
56.9
59.0
61.1
28.0
34.3
39.6
44.2
48.5
52.3
56.0
59.4
62.6
65.6
68.5
71.3
74.0
76.6
11.7
14.3
16.5
18.5
20.2
21.8
23.3
24.8
26.1
27.4
28.6
29.8
30.9
32.0
14.0
17.2
19.8
22.1
24.3
26.2
28.0
29.7
31.3
32.8
34.3
35.7
37.1
38.4
18.6
22.8
26.3
29.4
32.2
34.8
37.2
39.4
41.6
43.6
45.5
47.4
49.2
50.9
23.3
28.6
33.0
36.9
40.4
43.6
46.6
49.5
52.1
54.7
57.1
59.4
61.7
63.9
10.0
12.3
14.2
15.8
17.3
18.7
20.0
21.2
22.4
23.5
24.5
25.5
26.5
27.4
12.0
14.7
17.0
19.0
20.8
22.5
24.0
25.5
26.8
28.2
29.4
30.6
31.8
32.9
15.9
19.5
22.5
25.2
27.6
29.8
31.9
33.8
35.6
37.4
39.0
40.6
42.2
43.6
20.0
24.5
28.3
31.6
34.6
37.4
40.0
42.4
44.7
46.9
49.0
51.0
52.9
54.7
8.8
10.7
12.4
13.8
15.2
16.4
17.5
18.6
19.6
20.5
21.4
22.3
23.2
24.0
10.5
12.9
14.9
16.6
18.2
19.7
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.8
13.9
17.1
19.7
22.1
24.2
26.1
27.9
29.6
31.2
32.7
34.2
35.6
36.9
38.2
17.5
21.4
24.7
27.7
30.3
32.7
35.0
37.1
39.1
41.0
42.8
44.6
46.3
47.9
7.8
9.5
11.0
12.3
13.5
14.6
15.6
16.5
17.4
18.3
19.1
19.8
20.6
21.3
9.3
11.4
13.2
14.8
16.2
17.5
18.7
19.8
20.9
21.9
22.9
23.8
24.7
25.6
12.4
15.2
17.5
19.6
21.5
23.2
24.8
26.3
27.7
29.1
30.4
31.6
32.8
33.9
15.5
19.0
22.0
24.6
26.9
29.1
31.1
33.0
34.8
36.5
38.1
39.6
41.1
42.6
Air Induction Spray Tips (Greenleaf Turbo Drop Nozzles)
20 Inch Nozzle Spacing
Medium Pressure TurboDrop® XL Nozzle (TDXL, TDCXL)
Optimal pressure range is 30-90 psi. Targeting 60 psi operating pressure will allow for greater
changes in speed and pressure. Max pressure is 120 psi. Higher pressures are recommended for
contact pesticides (60-120 psi).
At lower pressures, the spray angle of the exit tip will narrow by approximately 10-15% (making a
110 degree tip essentially a 90-100 degree tip). Make necessary boom height adjustment for desired overlap. (For 20" spacing, a height of 20-36" is recommended.)
Complete
Nozzle #
AM11001
TDXL-11001
TDCXL-11001
50 mesh screen
AM110015
TDXL-110015
TDCXL-110015
50 mesh screen
Liquid
Nozzle
Pressure
Capacity
PSI
GPM
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
120
130
140
150
0.07
0.09
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.17
0.18
0.19
0.19
0.11
0.13
0.15
0.17
0.18
0.20
0.21
0.22
0.24
0.25
0.26
0.26
0.27
0.28
0.29
GALLONS PER ACRE BASED ON 20” NOZZLE SPACING
4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 10 MPH 12 MPH 14 MPH 16 MPH 18 MPH
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
13.4
13.9
14.4
7.9
9.6
11.1
12.4
13.6
14.7
15.7
16.7
17.6
18.5
19.3
19.3
20.1
20.8
21.6
4.2
5.1
5.9
6.6
7.3
7.9
8.4
8.9
9.4
9.8
10.3
10.7
11.1
11.5
6.3
7.7
8.9
10.0
10.9
11.8
12.6
13.4
14.1
14.8
15.4
15.4
16.1
16.7
17.2
3.5
4.3
4.9
5.5
6.1
6.5
7.0
7.4
7.8
8.2
8.6
8.9
9.3
9.6
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
12.9
13.4
13.9
14.4
31
3.0
3.7
4.2
4.7
5.2
5.6
6.0
6.4
6.7
7.0
7.3
7.6
7.9
8.2
4.5
5.5
6.4
7.1
7.8
8.4
9.0
9.5
10.1
10.5
11.0
11.0
11.5
11.9
12.3
2.6
3.2
3.7
4.1
4.5
4.9
5.2
5.6
5.9
6.2
6.4
6.7
6.9
7.2
3.9
4.8
5.6
6.2
6.8
7.4
7.9
8.3
8.8
9.2
9.6
9.6
10.0
10.4
10.8
2.1
2.6
3.0
3.3
3.6
3.9
4.2
4.5
4.7
4.9
5.1
5.4
5.6
5.7
3.1
3.9
4.5
5.0
5.5
5.9
6.3
6.7
7.0
7.4
7.7
7.7
8.0
8.3
8.6
1.7
2.1
2.5
2.8
3.0
3.3
3.5
3.7
3.9
4.1
4.3
4.5
4.6
4.8
2.6
3.2
3.7
4.1
4.5
4.9
5.2
5.6
5.9
6.2
6.4
6.4
6.7
6.9
7.2
1.5
1.8
2.1
2.4
2.6
2.8
3.0
3.2
3.4
3.5
3.7
3.8
4.0
4.1
2.2
2.8
3.2
3.6
3.9
4.2
4.5
4.8
5.0
5.3
5.5
5.5
5.7
5.9
6.2
1.3
1.6
1.9
2.1
2.3
2.5
2.6
2.8
2.9
3.1
3.2
3.3
3.5
3.6
2.0
2.4
2.8
3.1
3.4
3.7
3.9
4.2
4.4
4.6
4.8
4.8
5.0
5.2
5.4
1.2
1.4
1.6
1.8
2.0
2.2
2.3
2.5
2.6
2.7
2.9
3.0
3.1
3.2
1.7
2.1
2.5
2.8
3.0
3.3
3.5
3.7
3.9
4.1
4.3
4.3
4.5
4.6
4.8
20 Inch Nozzle Spacing (continued)
Complete
Nozzle #
AM11002
TDXL-11002
TDCXL-11002
50 mesh screen
AM110025
TDXL-110025
TDCXL-110025
50 mesh screen
AM11003
TDXL-11003
TDCXL-11003
50 mesh screen
AM11004
TDXL-11004
TDCXL-11004
24 mesh screen
Liquid
Nozzle
Pressure
Capacity
PSI
GPM
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
0.14
0.17
0.20
0.22
0.24
0.26
0.28
0.30
0.32
0.33
0.35
0.36
0.37
0.39
0.18
0.22
0.25
0.28
0.31
0.33
0.35
0.37
0.40
0.41
0.43
0.45
0.47
0.48
0.21
0.26
0.30
0.34
0.37
0.40
0.42
0.45
0.47
0.50
0.52
0.54
0.56
0.58
0.28
0.35
0.40
0.45
0.49
0.53
0.57
0.60
0.63
0.66
0.69
0.72
0.75
0.77
GALLONS PER ACRE BASED ON 20” NOZZLE SPACING
4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 10 MPH 12 MPH 14 MPH 16 MPH 18 MPH
10.5
12.9
14.8
16.6
18.2
19.6
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.7
13.1
16.1
18.5
20.7
22.7
24.5
26.2
27.8
29.3
30.8
32.1
33.4
34.7
35.9
15.7
19.3
22.3
24.9
27.3
29.4
31.5
33.4
35.2
36.9
38.6
40.1
41.6
43.1
21.0
25.7
29.7
33.2
36.3
39.3
42.0
44.5
46.9
49.2
51.4
53.5
55.5
57.5
8.4
10.3
11.9
13.3
14.5
15.7
16.8
17.8
18.8
19.7
20.6
21.4
22.2
23.0
10.5
12.9
14.8
16.6
18.2
19.6
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.7
12.6
15.4
17.8
19.9
21.8
23.6
25.2
26.7
28.2
29.5
30.8
32.1
33.3
34.5
16.8
20.6
23.7
26.5
29.1
31.4
33.6
35.6
37.5
39.4
41.1
42.8
44.4
46.0
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.8
18.5
19.2
8.7
10.7
12.4
13.8
15.1
16.4
17.5
18.5
19.6
20.5
21.4
22.3
23.1
23.9
10.5
12.9
14.8
16.6
18.2
19.6
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.7
14.0
17.1
19.8
22.1
24.2
26.2
28.0
29.7
31.3
32.8
34.3
35.7
37.0
38.3
32
6.0
7.3
8.5
9.5
10.4
11.2
12.0
12.7
13.4
14.1
14.7
15.3
15.9
16.4
7.5
9.2
10.6
11.9
13.0
14.0
15.0
15.9
16.8
17.6
18.4
19.1
19.8
20.5
9.0
11.0
12.7
14.2
15.6
16.8
18.0
19.1
20.1
21.1
22.0
22.9
23.8
24.6
12.0
14.7
17.0
19.0
20.8
22.4
24.0
25.4
26.8
28.1
29.4
30.6
31.7
32.8
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
13.4
13.9
14.4
6.6
8.0
9.3
10.4
11.4
12.3
13.1
13.9
14.7
15.4
16.1
16.7
17.4
18.0
7.9
9.6
11.1
12.4
13.6
14.7
15.7
16.7
17.6
18.5
19.3
20.1
20.8
21.6
10.5
12.9
14.8
16.6
18.2
19.6
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.7
4.2
5.1
5.9
6.6
7.3
7.9
8.4
8.9
9.4
9.8
10.3
10.7
11.1
11.5
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
13.4
13.9
14.4
6.3
7.7
8.9
10.0
10.9
11.8
12.6
13.4
14.1
14.8
15.4
16.1
16.7
17.2
8.4
10.3
11.9
13.3
14.5
15.7
16.8
17.8
18.8
19.7
20.6
21.4
22.2
23.0
3.5
4.3
4.9
5.5
6.1
6.5
7.0
7.4
7.8
8.2
8.6
8.9
9.3
9.6
4.4
5.4
6.2
6.9
7.6
8.2
8.7
9.3
9.8
10.3
10.7
11.1
11.6
12.0
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
13.4
13.9
14.4
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.8
15.6
16.4
17.1
17.8
18.5
19.2
3.0
3.7
4.2
4.7
5.2
5.6
6.0
6.4
6.7
7.0
7.3
7.6
7.9
8.2
3.7
4.6
5.3
5.9
6.5
7.0
7.5
7.9
8.4
8.8
9.2
9.6
9.9
10.3
4.5
5.5
6.4
7.1
7.8
8.4
9.0
9.5
10.1
10.5
11.0
11.5
11.9
12.3
6.0
7.3
8.5
9.5
10.4
11.2
12.0
12.7
13.4
14.1
14.7
15.3
15.9
16.4
2.6
3.2
3.7
4.1
4.5
4.9
5.2
5.6
5.9
6.2
6.4
6.7
6.9
7.2
3.3
4.0
4.6
5.2
5.7
6.1
6.6
7.0
7.3
7.7
8.0
8.4
8.7
9.0
3.9
4.8
5.6
6.2
6.8
7.4
7.9
8.3
8.8
9.2
9.6
10.0
10.4
10.8
5.2
6.4
7.4
8.3
9.1
9.8
10.5
11.1
11.7
12.3
12.9
13.4
13.9
14.4
2.3
2.9
3.3
3.7
4.0
4.4
4.7
4.9
5.2
5.5
5.7
5.9
6.2
6.4
2.9
3.6
4.1
4.6
5.0
5.5
5.8
6.2
6.5
6.8
7.1
7.4
7.7
8.0
3.5
4.3
4.9
5.5
6.1
6.5
7.0
7.4
7.8
8.2
8.6
8.9
9.3
9.6
4.7
5.7
6.6
7.4
8.1
8.7
9.3
9.9
10.4
10.9
11.4
11.9
12.3
12.8
20 Inch Nozzle Spacing (continued)
Complete
Nozzle #
AM11005
TDXL-11005
TDCXL-11005
24 mesh screen
AM11006
TDXL-11006
TDCXL-11006
24 mesh screen
TDXL-11008
TDCXL-11008
TDXL-11010
TDCXL-11010
Liquid
Nozzle
Pressure
Capacity
PSI
GPM
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
20
30
40
50
60
70
80
90
100
110
120
130
140
150
0.35
0.43
0.50
0.56
0.61
0.66
0.71
0.75
0.79
0.83
0.87
0.90
0.94
0.97
0.42
0.52
0.60
0.67
0.74
0.79
0.85
0.90
0.95
1.00
1.04
1.08
1.12
1.16
0.56
0.69
0.80
0.89
0.98
1.05
1.13
1.20
1.26
1.32
1.38
1.44
1.49
1.54
0.71
0.87
1.00
1.12
1.22
1.32
1.41
1.50
1.58
1.66
1.73
1.80
1.87
1.94
GALLONS PER ACRE BASED ON 20” NOZZLE SPACING
4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 10 MPH 12 MPH 14 MPH 16 MPH 18 MPH
26.3
32.2
37.1
41.5
45.5
49.1
52.5
55.7
58.7
61.6
64.3
67.0
69.5
71.9
31.5
38.6
44.6
49.8
54.6
59.0
63.0
66.8
70.5
73.9
77.2
80.3
83.4
86.3
41.8
51.2
59.2
66.2
72.5
78.3
83.7
88.8
93.6
98.1
102.5
106.7
110.7
114.6
52.5
64.3
74.2
83.0
90.9
98.2
104.9
111.3
117.3
123.0
128.5
133.8
138.8
143.7
21.0
25.7
29.7
33.2
36.4
39.3
42.0
44.6
47.0
49.3
51.5
53.6
55.6
57.5
25.2
30.9
35.7
39.9
43.7
47.2
50.4
53.5
56.4
59.1
61.8
64.3
66.7
69.0
33.5
41.0
47.3
52.9
58.0
62.6
66.9
71.0
74.8
78.5
82.0
85.3
88.6
91.7
42.0
51.4
59.4
66.4
72.7
78.5
83.9
89.0
93.9
98.4
102.8
107.0
111.0
114.9
17.5
21.4
24.8
27.7
30.3
32.8
35.0
37.1
39.2
41.1
42.9
44.6
46.3
48.0
21.0
25.7
29.7
33.2
36.4
39.3
42.0
44.6
47.0
49.3
51.5
53.6
55.6
57.5
27.9
34.2
39.4
44.1
48.3
52.2
55.8
59.2
62.4
65.4
68.3
71.1
73.8
76.4
35.0
42.8
49.5
55.3
60.6
65.4
70.0
74.2
78.2
82.0
85.7
89.2
92.5
95.8
33
15.0
18.4
21.2
23.7
26.0
28.1
30.0
31.8
33.6
35.2
36.8
38.3
39.7
41.1
18.0
22.1
25.5
28.5
31.2
33.7
36.0
38.2
40.3
42.2
44.1
45.9
47.6
49.3
23.9
29.3
33.8
37.8
41.4
44.7
47.8
50.7
53.5
56.1
58.6
61.0
63.3
65.5
30.0
36.7
42.4
47.4
51.9
56.1
60.0
63.6
67.0
70.3
73.4
76.4
79.3
82.1
13.1
16.1
18.6
20.8
22.7
24.6
26.3
27.9
29.4
30.8
32.2
33.5
34.7
36.0
15.8
19.3
22.3
24.9
27.3
29.5
31.5
33.4
35.2
37.0
38.6
40.2
41.7
43.1
20.9
25.6
29.6
33.1
36.2
39.1
41.8
44.4
46.8
49.1
51.2
53.3
55.3
57.3
26.2
32.1
37.1
41.5
45.4
49.1
52.5
55.6
58.7
61.5
64.3
66.9
69.4
71.8
10.5
12.9
14.9
16.6
18.2
19.7
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.8
12.6
15.4
17.8
19.9
21.8
23.6
25.2
26.7
28.2
29.6
30.9
32.1
33.3
34.5
16.7
20.5
23.7
26.5
29.0
31.3
33.5
35.5
37.4
39.2
41.0
42.7
44.3
45.8
21.0
25.7
29.7
33.2
36.3
39.3
42.0
44.5
46.9
49.2
51.4
53.5
55.5
57.5
8.8
10.7
12.4
13.8
15.2
16.4
17.5
18.6
19.6
20.5
21.4
22.3
23.2
24.0
10.5
12.9
14.9
16.6
18.2
19.7
21.0
22.3
23.5
24.6
25.7
26.8
27.8
28.8
13.9
17.1
19.7
22.1
24.2
26.1
27.9
29.6
31.2
32.7
34.2
35.6
36.9
38.2
17.5
21.4
24.7
27.7
30.3
32.7
35.0
37.1
39.1
41.0
42.8
44.6
46.3
47.9
7.5
9.2
10.6
11.9
13.0
14.0
15.0
15.9
16.8
17.6
18.4
19.1
19.9
20.6
9.0
11.0
12.7
14.2
15.6
16.8
18.0
19.1
20.1
21.1
22.1
23.0
23.8
24.7
12.0
14.6
16.9
18.9
20.7
22.4
23.9
25.4
26.7
28.0
29.3
30.5
31.6
32.7
15.0
18.4
21.2
23.7
26.0
28.0
30.0
31.8
33.5
35.2
36.7
38.2
39.7
41.1
6.6
8.0
9.3
10.4
11.4
12.3
13.1
13.9
14.7
15.4
16.1
16.7
17.4
18.0
7.9
9.6
11.1
12.5
13.6
14.7
15.8
16.7
17.6
18.5
19.3
20.1
20.8
21.6
10.5
12.8
14.8
16.5
18.1
19.6
20.9
22.2
23.4
24.5
25.6
26.7
27.7
28.6
13.1
16.1
18.5
20.7
22.7
24.5
26.2
27.8
29.3
30.8
32.1
33.4
34.7
35.9
5.8
7.1
8.3
9.2
10.1
10.9
11.7
12.4
13.1
13.7
14.3
14.9
15.4
16.0
7.0
8.6
9.9
11.1
12.1
13.1
14.0
14.9
15.7
16.4
17.2
17.9
18.5
19.2
9.3
11.4
13.1
14.7
16.1
17.4
18.6
19.7
20.8
21.8
22.8
23.7
24.6
25.5
11.7
14.3
16.5
18.4
20.2
21.8
23.3
24.7
26.1
27.3
28.6
29.7
30.8
31.9
TeeJet Air Induction Spray Tips
At Various Speeds And Pressures
20 Inch Tip Spacing
34
TeeJet Application Rates in Gallons Per Acre
At Various Speeds And Pressures
15 Inch Tip Spacing
Tip Size
XR11001VS
XR11015VS
XR11002VS
XR11003VS
Pressure
(PSI)
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
Nozzle
Capacity
(GPM)
0.06
0.07
0.08
0.09
0.09
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.09
0.11
0.12
0.13
0.14
0.15
0.17
0.18
0.20
0.21
0.23
0.24
0.12
0.14
0.16
0.17
0.19
0.20
0.22
0.24
0.26
0.28
0.30
0.32
0.18
0.21
0.24
0.26
0.28
0.30
0.34
0.37
0.40
0.42
0.45
0.47
Nozzle
Capacity
(oz/min)
8
9
10
12
12
13
14
15
17
18
19
20
12
14
15
17
18
19
22
23
26
27
29
31
15
18
20
22
24
26
28
31
33
36
38
41
23
27
31
33
36
38
44
47
51
54
58
60
5
MPH
4.8
5.5
6.3
7.1
7.1
7.9
8.7
9.5
10.3
11.1
11.9
12.7
7.1
8.7
9.5
10.3
11.1
11.9
13.5
14.3
15.8
17
18
19
9.5
11.1
12.7
13.5
15.0
15.8
17
19
21
22
24
25
14.3
17
19
21
22
24
27
29
32
33
36
37
6
MPH
4.0
4.6
5.3
5.9
5.9
6.6
7.3
7.9
8.6
9.2
9.9
10.6
5.9
7.3
7.9
8.6
9.2
9.9
11.2
11.9
13.2
13.9
15.2
15.8
7.9
9.2
10.6
11.2
12.5
13.2
14.5
15.8
17.2
18
20
21
11.9
13.9
15.8
17.2
18
20
22
24
26
28
30
31
35
15 INCH TIP SPACING
7
8
10
12
MPH MPH MPH MPH
3.4
3.0
2.4
2.0
4.0
3.5
2.8
2.3
4.5
4.0
3.2
2.6
5.1
4.5
3.6
3.0
5.1
4.5
3.6
3.0
5.7
5.0
4.0
3.3
6.2
5.4
4.4
3.6
6.8
5.9
4.8
4.0
7.4
6.4
5.1
4.3
7.9
6.9
5.5
4.6
8.5
7.4
5.9
5.0
9.1
7.9
6.3
5.3
5.1
4.5
3.6
3.0
6.2
5.4
4.4
3.6
6.8
5.9
4.8
4.0
7.4
6.4
5.1
4.3
7.9
6.9
5.5
4.6
8.5
7.4
5.9
5.0
9.6
8.4
6.7
5.6
10.2 8.9
7.1
5.9
11.3 9.9
7.9
6.6
11.9 10.4 8.3
6.9
13.0 11.4 9.1
7.6
13.6 11.9 9.5
7.9
6.8
5.9
4.8
4.0
7.9
6.9
5.5
4.6
9.1
7.9
6.3
5.3
9.6
8.4
6.7
5.6
10.7 9.4
7.5
6.3
11.3 9.9
7.9
6.6
12.4 10.9 8.7
7.3
13.6 11.9 9.5
7.9
14.7 12.9 10.3 8.6
15.8 13.9 11.1 9.2
17.0 14.9 11.9 9.9
18.1 15.8 12.7 10.6
10.2 8.9
7.1
5.9
11.9 10.4 8.3
6.9
13.6 11.9 9.5
7.9
14.7 12.9 10.3 8.6
15.8 13.9 11.1 9.2
17.0 14.9 11.9 9.9
19 16.8 13.5 11.2
21 18.3 14.7 12.2
23 19.8 15.8 13.2
24
21 16.6 13.9
25
22 17.8 14.9
27
23 18.6 15.5
13
MPH
1.8
2.1
2.4
2.7
2.7
3.0
3.4
3.7
4.0
4.3
4.6
4.9
2.7
3.4
3.7
4.0
4.3
4.6
5.2
5.5
6.1
6.4
7.0
7.3
3.7
4.3
4.9
5.2
5.8
6.1
6.7
7.3
7.9
8.5
9.1
9.7
5.5
6.4
7.3
7.9
8.5
9.1
10.4
11.3
12.2
12.8
13.7
14.3
14
MPH
1.7
2.0
2.3
2.5
2.5
2.8
3.1
3.4
3.7
4.0
4.2
4.5
2.5
3.1
3.4
3.7
4.0
4.2
4.8
5.1
5.7
5.9
6.5
6.8
3.4
4.0
4.5
4.8
5.4
5.7
6.2
6.8
7.4
7.9
8.5
9.1
5.1
5.9
6.8
7.4
7.9
8.5
9.6
10.5
11.3
11.9
12.7
13.3
16
18
MPH MPH
1.5
1.3
1.7
1.5
2.0
1.8
2.2
2.0
2.2
2.0
2.5
2.2
2.7
2.4
3.0
2.6
3.2
2.9
3.5
3.1
3.7
3.3
4.0
3.5
2.2
2.0
2.7
2.4
3.0
2.6
3.2
2.9
3.5
3.1
3.7
3.3
4.2
3.7
4.5
4.0
5.0
4.4
5.2
4.6
5.7
5.1
5.9
5.3
3.0
2.6
3.5
3.1
4.0
3.5
4.2
3.7
4.7
4.2
5.0
4.4
5.4
4.8
5.9
5.3
6.4
5.7
6.9
6.2
7.4
6.6
7.9
7.0
4.5
4.0
5.2
4.6
5.9
5.3
6.4
5.7
6.9
6.2
7.4
6.6
8.4
7.5
9.2
8.1
9.9
8.8
10.4 9.2
11.1 9.9
11.6 10.3
15 Inch Tip Spacing (continued)
Tip Size
XR11004VS
XR11005VS
XR11006VS
XR11008VS
Pressure
(PSI)
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
Nozzle
Capacity
(GPM)
0.24
0.28
0.32
0.35
0.37
0.40
0.45
0.49
0.53
0.57
0.60
0.63
0.31
0.35
0.40
0.43
0.47
0.50
0.56
0.61
0.66
0.71
0.75
0.79
0.37
0.42
0.47
0.52
0.56
0.60
0.67
0.73
0.79
0.85
0.90
0.95
0.49
0.57
0.63
0.69
0.75
0.80
0.89
0.98
1.06
1.13
1.20
1.26
Nozzle
Capacity
5
6
(oz/min) MPH MPH
31
19 15.8
36
22
18
41
25
21
45
28
23
47
29
24
51
32
26
58
36
30
63
39
32
68
42
35
73
45
38
77
48
40
81
50
42
40
25
20
45
28
23
51
32
26
55
34
28
60
37
31
64
40
33
72
44
37
78
48
40
84
52
44
91
56
47
96
59
50
101
63
52
47
29
24
54
33
28
60
37
31
67
41
34
72
44
37
77
48
40
86
53
44
93
58
48
101
63
52
109
67
56
115
71
59
122
75
63
63
39
32
73
45
38
81
50
42
88
55
46
96
59
50
102
63
53
114
70
59
125
78
65
136
84
70
145
89
75
154
95
79
161
100
83
36
15 INCH TIP SPACING
7
8
10
12
MPH MPH MPH MPH
13.6 11.9 9.5
7.9
15.8 13.9 11.1 9.2
18.1 15.8 12.7 10.6
20 17.3 13.9 11.6
21 18.3 14.7 12.2
23 19.8 15.8 13.2
25
22 17.8 14.9
28
24 19.4 16.2
30
26 21.0 17.5
32
28
23 18.8
34
30
24 19.8
36
31
25 20.8
17.5 15.3 12.3 10.2
20 17.3 13.9 11.6
23 19.8 15.8 13.2
24
21 17.0 14.2
27
23 18.6 15.5
28
25 19.8 16.5
32
28
22 18.5
35
30
24 20.1
37
33
26
22
40
35
28
23
42
37
30
25
45
39
31
26
21 18.3 14.7 12.2
24
21 16.6 13.9
27
23 18.6 15.5
29
26 20.6 17.2
32
28
22 18.5
34
30
24 19.8
38
33
27
22
41
36
29
24
45
39
31
26
48
42
34
28
51
45
36
30
54
47
38
31
28
24 19.4 16.2
32
28
23 18.8
36
31
25 20.8
39
34
27
23
42
37
30
25
45
40
32
26
50
44
35
29
55
49
39
32
60
52
42
35
64
56
45
37
68
59
48
40
71
62
50
42
13
MPH
7.3
8.5
9.7
10.7
11.3
12.2
13.7
14.9
16.1
17.4
18.3
19.2
9.4
10.7
12.2
13.1
14.3
15.2
17.1
18.6
20.1
21.6
22.8
24
11.3
12.8
14.3
15.8
17.1
18.3
20.4
22.2
24
26
27
29
14.9
17.4
19.2
21.0
22.8
24
27
30
32
34
37
38
14
MPH
6.8
7.9
9.1
9.9
10.5
11.3
12.7
13.9
15.0
16.1
17.0
17.8
8.8
9.9
11.3
12.2
13.3
14.1
15.8
17.3
18.7
20.1
21.2
22.3
10.5
11.9
13.3
14.7
15.8
17.0
19.0
20.6
22.3
24.0
25.5
27
13.9
16.1
17.8
19.5
21.2
22.6
25.2
28
30
32
34
36
16
MPH
5.9
6.9
7.9
8.7
9.2
9.9
11.1
12.1
13.1
14.1
14.9
15.6
7.7
8.7
9.9
10.6
11.6
12.4
13.9
15.1
16.3
17.6
18.6
19.6
9.2
10.4
11.6
12.9
13.9
14.9
16.6
18.1
19.6
21.0
22.3
23.5
12.1
14.1
15.6
17.1
18.6
19.8
22.0
24.3
26.2
28
30
31
18
MPH
5.3
6.2
7.0
7.7
8.1
8.8
9.9
10.8
11.7
12.5
13.2
13.9
6.8
7.7
8.8
9.5
10.3
11.0
12.3
13.4
14.5
15.6
16.5
17.4
8.1
9.2
10.3
11.4
12.3
13.2
14.7
16.1
17.4
18.7
19.8
20.9
10.8
12.5
13.9
15.2
16.5
17.6
19.6
21.6
23.3
24.9
26.4
28
15 Inch Tip Spacing (continued)
Tip Size
XR11010-SS
XR11015-SS
Pressure
(PSI)
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
Nozzle
Capacity
(GPM)
0.61
0.71
0.79
0.87
0.94
1.00
1.12
1.22
1.32
1.41
1.50
1.58
0.92
1.06
1.19
1.30
1.40
1.50
1.68
1.84
1.98
2.12
2.25
2.37
Nozzle
Capacity
5
6
(oz/min) MPH MPH
78
48
40
91
56
47
101
63
52
111
69
57
120
74
62
128
79
66
143
89
74
156
97
81
169
105
87
180
112
93
192
119
99
202
125 104
118
73
61
136
84
70
152
94
79
166
103
86
179
111
92
192
119
99
215
133 111
236
146 121
253
157 131
271
168 140
288
178 149
303
188 156
37
15 INCH TIP SPACING
7
8
10
12
MPH MPH MPH MPH
35
30 24.2 20
40
35 28.1 23
45
39
31
26
49
43
34
29
53
47
37
31
57
50
40
33
63
55
44
37
69
60
48
40
75
65
52
44
80
70
56
47
85
74
59
50
89
78
63
52
52
46 36.4 30
60
52 42.0 35
67
59
47
39
74
64
51
43
79
69
55
46
85
74
59
50
95
83
67
55
104
91
73
61
112
98
78
65
120 105
84
70
127 111
89
74
134 117
94
78
13
MPH
18.6
22
24
27
29
30
34
37
40
43
46
48
28
32
36
40
43
46
51
56
60
65
69
72
14
MPH
17.3
20.1
22
25
27
28
32
35
37
40
42
45
26.0
30
34
37
40
42
48
52
56
60
64
67
16
MPH
15.1
17.6
19.6
22
23
25
28
30
33
35
37
39
22.8
26.2
29
32
35
37
42
46
49
52
56
59
18
MPH
13.4
15.6
17.4
19.1
21
22
25
27
29
31
33
35
20.2
23.3
26.2
29
31
33
37
40
44
47
50
52
20 Inch Tip Spacing
Tip Size
XR11001VS
XR110015VS
XR11002VS
XR11003VS
Pressure
(PSI)
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
Nozzle
Capacity
(GPM)
0.06
0.07
0.08
0.09
0.09
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.09
0.11
0.12
0.13
0.14
0.15
0.17
0.18
0.20
0.21
0.23
0.24
0.12
0.14
0.16
0.17
0.19
0.20
0.22
0.24
0.26
0.28
0.30
0.32
0.18
0.21
0.24
0.26
0.28
0.30
0.34
0.37
0.40
0.42
0.45
0.47
Nozzle
Capacity
(oz/min)
8
9
10
12
12
13
14
15
17
18
19
20
12
14
15
17
18
19
22
23
26
27
29
31
15
18
20
22
24
26
28
31
33
36
38
41
23
27
31
33
36
38
44
47
51
54
58
60
5
MPH
3.6
4.2
4.8
5.3
5.3
5.9
6.5
7.1
7.7
8.3
8.9
9.5
5.3
6.5
7.1
7.7
8.3
8.9
10.1
10.7
11.9
12
14
14
7.1
8.3
9.5
10.1
11.3
11.9
13
14
15
17
18
19
10.7
12
14
15
17
18
20
22
24
25
27
28
6
MPH
3.0
3.5
4.0
4.5
4.5
5.0
5.4
5.9
6.4
6.9
7.4
7.9
4.5
5.4
5.9
6.4
6.9
7.4
8.4
8.9
9.9
10.4
11.4
11.9
5.9
6.9
7.9
8.4
9.4
9.9
10.9
11.9
12.9
14
15
16
8.9
10.4
11.9
12.9
14
15
17
18
20
21
22
23
38
20 INCH TIP SPACING
7
8
10
12
MPH MPH MPH MPH
2.5
2.2
1.8
1.5
3.0
2.6
2.1
1.7
3.4
3.0
2.4
2.0
3.8
3.3
2.7
2.2
3.8
3.3
2.7
2.2
4.2
3.7
3.0
2.5
4.7
4.1
3.3
2.7
5.1
4.5
3.6
3.0
5.5
4.8
3.9
3.2
5.9
5.2
4.2
3.5
6.4
5.6
4.5
3.7
6.8
5.9
4.8
4.0
3.8
3.3
2.7
2.2
4.7
4.1
3.3
2.7
5.1
4.5
3.6
3.0
5.5
4.8
3.9
3.2
5.9
5.2
4.2
3.5
6.4
5.6
4.5
3.7
7.2
6.3
5.0
4.2
7.6
6.7
5.3
4.5
8.5
7.4
5.9
5.0
8.9
7.8
6.2
5.2
9.8
8.5
6.8
5.7
10.2 8.9
7.1
5.9
5.1
4.5
3.6
3.0
5.9
5.2
4.2
3.5
6.8
5.9
4.8
4.0
7.2
6.3
5.0
4.2
8.1
7.1
5.6
4.7
8.5
7.4
5.9
5.0
9.3
8.2
6.5
5.4
10.2 8.9
7.1
5.9
11.0 9.7
7.7
6.4
11.9 10.4 8.3
6.9
12.7 11.1 8.9
7.4
13.6 11.9 9.5
7.9
7.6
6.7
5.3
4.5
8.9
7.8
6.2
5.2
10.2 8.9
7.1
5.9
11.0 9.7
7.7
6.4
11.9 10.4 8.3
6.9
12.7 11.1 8.9
7.4
14 12.6 10.1 8.4
16 13.7 11.0 9.2
17 14.9 11.9 9.9
18
16 12.5 10.4
19
17 13.4 11.1
20
17 14.0 11.6
13
14
16
18
MPH MPH MPH MPH
1.4
1.3
1.1
1.0
1.6
1.5
1.3
1.2
1.8
1.7
1.5
1.3
2.1
1.9
1.7
1.5
2.1
1.9
1.7
1.5
2.3
2.1
1.9
1.7
2.5
2.3
2.0
1.8
2.7
2.5
2.2
2.0
3.0
2.8
2.4
2.1
3.2
3.0
2.6
2.3
3.4
3.2
2.8
2.5
3.7
3.4
3.0
2.6
2.1
1.9
1.7
1.5
2.5
2.3
2.0
1.8
2.7
2.5
2.2
2.0
3.0
2.8
2.4
2.1
3.2
3.0
2.6
2.3
3.4
3.2
2.8
2.5
3.9
3.6
3.2
2.8
4.1
3.8
3.3
3.0
4.6
4.2
3.7
3.3
4.8
4.5
3.9
3.5
5.3
4.9
4.3
3.8
5.5
5.1
4.5
4.0
2.7
2.5
2.2
2.0
3.2
3.0
2.6
2.3
3.7
3.4
3.0
2.6
3.9
3.6
3.2
2.8
4.3
4.0
3.5
3.1
4.6
4.2
3.7
3.3
5.0
4.7
4.1
3.6
5.5
5.1
4.5
4.0
5.9
5.5
4.8
4.3
6.4
5.9
5.2
4.6
6.9
6.4
5.6
5.0
7.3
6.8
5.9
5.3
4.1
3.8
3.3
3.0
4.8
4.5
3.9
3.5
5.5
5.1
4.5
4.0
5.9
5.5
4.8
4.3
6.4
5.9
5.2
4.6
6.9
6.4
5.6
5.0
7.8
7.2
6.3
5.6
8.5
7.8
6.9
6.1
9.1
8.5
7.4
6.6
9.6
8.9
7.8
6.9
10.3 9.5
8.4
7.4
10.7 10.0 8.7
7.8
20 Inch Tip Spacing (continued)
Tip Size
XR11004VS
XR11005VS
XR11006VS
XR11008VS
Pressure
(PSI)
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
Nozzle
Capacity
(GPM)
0.24
0.28
0.32
0.35
0.37
0.40
0.45
0.49
0.53
0.57
0.60
0.63
0.31
0.35
0.40
0.43
0.47
0.50
0.56
0.61
0.66
0.71
0.75
0.79
0.37
0.42
0.47
0.52
0.56
0.60
0.67
0.73
0.79
0.85
0.90
0.95
0.49
0.57
0.63
0.69
0.75
0.80
0.89
0.98
1.06
1.13
1.20
1.26
Nozzle
Capacity
5
6
(oz/min) MPH MPH
31
14 11.9
36
17
14
41
19
16
45
21
17
47
22
18
51
24
20
58
27
22
63
29
24
68
31
26
73
34
28
77
36
30
81
37
31
40
18
15
45
21
17
51
24
20
55
26
21
60
28
23
64
30
25
72
33
28
78
36
30
84
39
33
91
42
35
96
45
37
101
47
39
47
22
18
54
25
21
60
28
23
67
31
26
72
33
28
77
36
30
86
40
33
93
43
36
101
47
39
109
50
42
115
53
45
122
56
47
63
29
24
73
34
28
81
37
31
88
41
34
96
45
37
102
48
40
114
53
44
125
58
49
136
63
52
145
67
56
154
71
59
161
75
62
39
20 INCH TIP SPACING
7
8
10
12
MPH MPH MPH MPH
10.2 8.9
7.1
5.9
11.9 10.4 8.3
6.9
13.6 11.9 9.5
7.9
15 13.0 10.4 8.7
16 13.7 11.0 9.2
17 14.9 11.9 9.9
19
17 13.4 11.1
21
18 14.6 12.1
22
20 15.7 13.1
24
21
17 14.1
25
22
18 14.9
27
23
19 15.6
13.2 11.5 9.2
7.7
15 13.0 10.4 8.7
17 14.9 11.9 9.9
18
16 12.8 10.6
20
17 14.0 11.6
21
19 14.9 12.4
24
21
17 13.9
26
23
18 15.1
28
25
20
16
30
26
21
18
32
28
22
19
34
29
23
20
16 13.7 11.0 9.2
18
16 12.5 10.4
20
17 14.0 11.6
22
19 15.4 12.9
24
21
17 13.9
25
22
18 14.9
28
25
20
17
31
27
22
18
34
29
23
20
36
32
25
21
38
33
27
22
40
35
28
24
21
18 14.6 12.1
24
21
17 14.1
27
23
19 15.6
29
26
20
17
32
28
22
19
34
30
24
20
38
33
26
22
42
36
29
24
45
39
31
26
48
42
34
28
51
45
36
30
53
47
37
31
13
MPH
5.5
6.4
7.3
8.0
8.5
9.1
10.3
11.2
12.1
13.0
13.7
14.4
7.1
8.0
9.1
9.8
10.7
11.4
12.8
13.9
15.1
16.2
17.1
18
8.5
9.6
10.7
11.9
12.8
13.7
15.3
16.7
18
19
21
22
11.2
13.0
14.4
15.8
17.1
18
20
22
24
26
27
29
14
MPH
5.1
5.9
6.8
7.4
7.8
8.5
9.5
10.4
11.2
12.1
12.7
13.4
6.6
7.4
8.5
9.1
10.0
10.6
11.9
12.9
14.0
15.1
15.9
16.8
7.8
8.9
10.0
11.0
11.9
12.7
14.2
15.5
16.8
18.0
19.1
20
10.4
12.1
13.4
14.6
15.9
17.0
18.9
21
22
24
25
27
16
MPH
4.5
5.2
5.9
6.5
6.9
7.4
8.4
9.1
9.8
10.6
11.1
11.7
5.8
6.5
7.4
8.0
8.7
9.3
10.4
11.3
12.3
13.2
13.9
14.7
6.9
7.8
8.7
9.7
10.4
11.1
12.4
13.6
14.7
15.8
16.7
17.6
9.1
10.6
11.7
12.8
13.9
14.9
16.5
18.2
19.7
21
22
23
18
MPH
4.0
4.6
5.3
5.8
6.1
6.6
7.4
8.1
8.7
9.4
9.9
10.4
5.1
5.8
6.6
7.1
7.8
8.3
9.2
10.1
10.9
11.7
12.4
13.0
6.1
6.9
7.8
8.6
9.2
9.9
11.1
12.0
13.0
14.0
14.9
15.7
8.1
9.4
10.4
11.4
12.4
13.2
14.7
16.2
17.5
18.6
19.8
21
20 Inch Tip Spacing (continued)
Tip Size
XR11010-SS
XR11015-SS
Pressure
(PSI)
15
20
25
30
35
40
50
60
70
80
90
100
15
20
25
30
35
40
50
60
70
80
90
100
Nozzle
Capacity
(GPM)
0.61
0.71
0.79
0.87
0.94
1.00
1.12
1.22
1.32
1.41
1.50
1.58
0.92
1.06
1.19
1.30
1.40
1.50
1.68
1.84
1.98
2.12
2.25
2.37
Nozzle
20 INCH TIP SPACING
Capacity
5
6
7
8
10
12
(oz/min) MPH MPH MPH MPH MPH MPH
78
36
30
26
23 18.1 15
91
42
35
30
26 21.1 18
101
47
39
34
29
23
20
111
52
43
37
32
26
22
120
56
47
40
35
28
23
128
59
50
42
37
30
25
143
67
55
48
42
33
28
156
72
60
52
45
36
30
169
78
65
56
49
39
33
180
84
70
60
52
42
35
192
89
74
64
56
45
37
202
94
78
67
59
47
39
118
55
46
39
34 27.3 23
136
63
52
45
39 31.5 26
152
71
59
50
44
35
29
166
77
64
55
48
39
32
179
83
69
59
52
42
35
192
89
74
64
56
45
37
215
100
83
71
62
50
42
236
109
91
78
68
55
46
253
118
98
84
74
59
49
271
126 105
90
79
63
52
288
134 111
95
84
67
56
303
141 117 101
88
70
59
40
13
MPH
13.9
16
18
20
21
23
26
28
30
32
34
36
21
24
27
30
32
34
38
42
45
48
51
54
14
MPH
12.9
15.1
17
18
20
21
24
26
28
30
32
34
19.5
22
25
28
30
32
36
39
42
45
48
50
16
MPH
11.3
13.2
14.7
16
17
19
21
23
25
26
28
29
17.1
19.7
22
24
26
28
31
34
37
39
42
44
18
MPH
10.1
11.7
13.0
14.4
16
17
18
20
22
23
25
26
15.2
17.5
19.6
21
23
25
28
30
33
35
37
39
TeeJet FloodJet Wide Angle Flat Spray Tips
At Various Speeds And Pressures
40 Inch Tip Spacing
41
Sprayer Controls
Sprayer operation and liquid flows are controlled by a combination of controls on the tractor and the
sprayer.
Triple Electric Control (Standard)
This system consists of three electric ball valves and a electric pressure regulating valve which are
all mounted on the top of the boom mid section of the sprayer. The control box is mounted on the
tractor.
Electric Pressure
Regulating Valve
Electric Ball Valves
Standard Control Box
42
Control Box
The control box consists of the following components:
•
MASTER ON/OFF switch which controls power to the valves for each boom section. When
power is supplied to the valves, the valves open, allowing liquid to flow to the boom sections.
NOTE: The toggle switches for the individual boom sections must be ON to energize the valves.
•
Individual toggle switches which allow the operator to control flow to the individual boom sections
(L, left; C, center; and R, right). Turning a switch OFF allows the valve for that section to close.
•
PRESSURE ADJUST toggle switch which allows the operator to INCREASE (+) or DECREASE (-) the pressure of the liquid supplied to the boom sections. When the operator releases the switch after adjusting the pressure, the switch automatically returns to its center
NEUTRAL position.
NOTE: When making adjustments, monitor pressure carefully. The control system does not have
automatic HIGH or LOW pressure limit switches.
•
PRESSURE GAUGE which indicates the pressure of the liquid supplied to the operating boom
sections.
If the operator shuts OFF a boom section, the pressure of liquid supplied to the other two boom
sections will increase because the same volume of liquid is being pumped through fewer nozzles.
The operator must use the pressure adjust switch on the control box to manually reduce the pressure to the operating pressure desired.
Standard Control Box
Pressure Adjust Switch
Pressure Gauge
Master ON/OFF Switch
Boom Section
Switches
43
Optional Automatic Rate Controller
Automatic rate controllers are an optional accessory on all sprayers. Refer to the separate owners
manual for detailed instructions for using the system.
Optional Four-Way Electric Control System with RAVEN Rate Control System Only
The four-way electric control system has the same features as the three-way control system.
However, it uses four motorized ball valves which allow the boom to be split into four sections: Left,
Left Center, Right Center and Right. The control box has additional switches to provide four section
boom control.
Valve Control Center
The valve control center is located in front of the sprayer platform. The number of valves on the
control center will vary, depending upon if the sprayer is equipped with group “A” or “C” option
package.
Each valve controls the following (top to bottom):
•
Top Valve is for hand spray gun
•
Valve A is for rinse tank fill
•
Valve B is for product tank rinse
•
Valve C is for product tank fill
•
Valve D is for the chemical inductor
•
Bottom Valve is the agitation throttling valve
Hand Gun Valve
Valve A
Valve B
Valve C
Valve D
Agitation Throttling
Valve
44
Agitation System
Your sprayer is equipped with an adjustable agitation system. The throttling valve to adjust the
system can be located in one of two locations, depending on which accessories your sprayer is
equipped with.
If the sprayer does not have a self cleaning filter, the agitation throttling valve will be located near the
front left corner of the sprayer platform.
Agitation
Throttling
Valve
If the sprayer has a self cleaning filter, the agitation throttling valve will be the first valve located at
the bottom of the valve control center tower. See preceeding page for location.
There are four agitation jets inside the product tank. Two are located in the sump near the front of
the tank and two are located at the rear of the tank.
NOTE: If the sprayer is equipped with a self cleaning filter the two jets at the rear of the tank will be
controlled by the self cleaning filter. See the self cleaning filter section for details.
It is recommended that you have the agitation throttling valve completely OPEN unless foaming
occurs.
45
Standard Primary Filter
Your sprayer is equipped with a primary filtration system. This filter could be in the form of a “Y”
strainer (standard) or a self cleaning filter (optional). The filter is located on the right side of the
sprayer under the sprayer platform. The filter is installed on the pressure side of the pump and has
a 50 mesh screen. Other size mesh screens are available through your local Miller dealer parts
department.
Self Cleaning Filter (Optional)
Refer to the “Maintenance” section of this manual for filter maintenance interval and
procedures
A self cleaning filter is an optional accessory. This filter has a throttling valve located in the front left
hand side of the sprayer. A quick coupler system and hose is mounted to the bottom of the filter
cannister. The unmixed chemical that does not go through the 50 mesh screen is returned to the
product tank through the rear agitation jets, reagitated and sent back through the system.
•
The throttling valve should remain completely open for the self cleaning filter to operate properly.
•
When the cannister is removed from the filter head, the throttling valve MUST be closed.
To clean the filter screen:
DANGER
Agricultural chemicals are TOXIC, chemicals not safely used, handled, stored
and disposed of can cause serious injury or death to individuals or harm the
environment.
Wear protective clothing and equipment.
Read, understand and follow the chemical manufacturer’s label.
Contact your chemical supplier, county extension agent or other qualified
person if you have questions on chemical usage.
1.
Turn the product pump OFF.
2.
Turn the emergency shut off valve (located under tank) OFF.
3.
Turn the agitation throttling valve (located in front of sprayer) OFF.
4.
Turn self cleaning filter on/off (located in front of sprayer) OFF - If so equipped.
5.
Place a container under the filter, remove the canister and screen, rinse the screen off with
clean water.
6.
Lightly oil the O-ring on the canister. Reinstall the canister and screen. DO NOT over tighten.
7.
OPEN all valves previously closed.
8.
Dispose of all captured chemicals properly.
46
Filling The Product Tank
NOTE: All poly tanks are not identical in capacity due to different tank molds, heat and/or cold.
Tank sizes can and do vary. It is recommended that you measure by an independent means the
amount of liquid being loaded.
The sprayer can be equipped in one of three ways:
•
No fast fill attachment - Standard configuration
•
2" Fast Fill via transfer pump - Optional (Group A)
•
2" Fast Fill via transfer pump or sprayer pump - Optional (Group C)
NOTE: If Group C is ordered, you have the option of Manual or Electric controls for the rinse system. Refer to the appropriate set of instructions that follows, depending on your sprayers configuration.
Fill Through Top Lid (Standard Configuration)
1.
Remove the lid from the top of the product tank. Fill the tank using a garden hose or similiar
means.
2.
Replace the lid when complete.
Filling With Transfer Pump
Your sprayer is equipped with a 2" male fast fill connector and a ON/OFF valve (identified as “Valve
F”) located on the left side of the sprayer, directly behind the step.
Fill as follows:
1.
Connect the fill hose to the 2" connector.
2.
Charge the fill hose with water using the transfer pump.
If Equipped With Manual Control Rinse System:
•
Turn the manual three way ball valve identified as “Valve E” (located under the platform on
left side of sprayer) to “Product Tank” (handle pointed toward rear of sprayer).
F
OFF
RINSE
TANK
E
PRODUCT
TANK
ON
OFF
If Equipped With Electric Control Rinse System:
•
Locate the electric rinse control switch on the tractor control box and move the switch to
the “Product Tank” position.
47
3.
Slowly open the “Fast Fill” valve, marked as “Valve F” and let run until the product tank is full,
turn off the “Fast Fill” valve. There is a breather on the product tank lid to allow air to escape
during the filling operation.
IMPORTANT: If you are filling with a high volume transfer pump, it may be necessary to
remove the center lid from the manhole cover.
F
OFF
RINSE
TANK
E
PRODUCT
TANK
ON
OFF
4.
Close the “Fast Fill” Valve.
5.
Disconnect the fill hose and replace the dust cap. Use care when removing the fill hose from
the connector, there could still be liquid in the line.
6.
Replace the center lid on the manhole cover, if it was removed.
Filling With Sprayer Pump
Your sprayer has the ability to fill itself by using the sprayer product pump.
Your sprayer is equipped with a 2" male fast fill connector and a ON/OFF valve (identified as “Valve
F”) located on the left side of the sprayer, directly behind the step.
Fill as follows:
1.
Connect the fill hose to the 2" connector.
2.
Open the water supply valve to fill the hose.
IMPORTANT: The water source MUST be higher than the sprayer pump. NEVER run the
sprayer pump dry. The sprayer pump will not draw water from a source lower than the
pump, until the pump is primed.
If Equipped With Manual Control Rinse System:
•
Turn the manual three way ball valve identified as “Valve E” (located under the platform on
left side of sprayer) to the “OFF” position (handle pointed down).
If Equipped With Electric Control Rinse System:
•
Located under the operator platform on the left side of the sprayer is an electric three way
ball valve. Directly behind this valve is a manual ON/OFF valve with a yellow handle.
Turn this valve OFF (handle should point toward rear of sprayer). When handle is pointed
toward right side of sprayer the valve is ON.
48
3.
Open the “Fast Fill” valve marked as “Valve F.”
4.
Start the product pump and run at full capacity.
5.
Slowly open the “Product Tank Fill” valve marked “Valve C” located on the front control stand.
Let run until the product tank is full, then turn OFF “Product Tank Fill” valve. There is a
breather on the product tank lid to allow air to escape during filling.
6.
Stop the product pump.
7.
Close the “Fast Fill” valve.
If Equipped With Manual Control Rinse System:
•
Turn the manual three way ball valve identified as “Valve E” (located under the platform on
left side of sprayer) to the “Product Tank” position (handle pointed toward rear of sprayer).
If Equipped With Electric Control Rinse System:
•
Located under the operator platform on the left side of the sprayer is an electric three way
ball valve. Directly behind this valve is a manual ON/OFF valve with a yellow handle.
Turn this valve ON (handle should point toward right side of sprayer). When handle is
pointed toward rear of sprayer the valve is OFF.
8.
Turn off the external water source.
9.
Remove the fill hose and replace the dust cap. Be careful when removing the fill hose from the
connector, there could still be some liquid in the line.
Yellow
Handle
Valve C
49
Electric 3 Way
Ball Valve
Priming The Sprayer
NOTE: Before you prime the sprayer, make sure you are familiar with the information in the pump
owner’s manual.
1.
Determine appropriate operating pressure for the sprayer system.
2.
Fill the sprayer tank half full of water. DO NOT add chemicals.
IMPORTANT: Water must be in pump before pump is started. Pump may be damaged if
pump and suction lines are empty. Use the transfer pump or fill through top port.
3.
Open the emergency shut-off valve to allow water to flow from the tank into the suction line
and pump. Make sure the three-way valve (if so equipped) is open to the product tank.
4.
Fold out the boom. (Refer to the “Hydraulic Booms” section of this manual for instructions).
5.
Start the tractor. Start the pump and operate at desired speed.
6.
Toggle the MASTER switch on the sprayer control box to the ON position to open the boom
control valves. The individual boom switches on the control box must also be ON.
7.
Make the pressure adjustment using the PRESSURE ADJUST switch on the control box.
8.
Check and adjust for adequate agitation in the sprayer tank. If the pressure drops, adjust the
pressure setting at the sprayer control box.
9.
Check for uniform flow at all the spray nozzles.
The sprayer is now ready for calibration.
50
Priming The Sprayer Equipped With A RAVEN Rate Controller
If your sprayer is equipped with a RAVEN rate controller, you must do the following to allow the
spray boom to function while standing still.
1.
Disconnect the radar cable between the tractor and the sprayer.
2.
Turn RAVEN console master switch ON.
3.
Press the “Self Test” button so the red light stays on.
4.
Press “Enter” so the red light stays on.
5.
Press the No.5 key and the No. 0 key.
6.
Press “Enter” again.
Now the RAVEN rate controller is programmed with a signal telling it that it is moving, allowing the
spray boom to operate while standing still.
To Disengage Signal
1.
Reconnect the radar cable between the tractor and the sprayer.
2.
Move the tractor and sprayer or turn the rate controller OFF and then back ON.
51
Calibrating The Sprayer
Your sprayer will be equipped with one of two different control systems:
•
TeeJet Electric Control System (standard)
•
Raven Rate Control System (optional)
The two systems need to be calibrated in different ways.
TeeJet Electric Control System (standard)
1.
Make sure sprayer is clean.
2.
Select nozzle and pressure.
3.
Fill sprayer half full with water. DO NOT add chemical.
4.
Set up two stakes at the following measurements, depending on nozzle spacing:
•
272 feet apart for 15" nozzle spacing
•
204 feet apart for 20" nozzle spacing
•
136 feet apart for 30" nozzle spacing
•
102 feet apart for 40" nozzle spacing
5.
Under field conditions and at spraying speed, drive the distance and note both engine RPMs
and the time. Do this at least twice to get the average time.
6.
Stop the tractor. Put the tractor in park.
7.
Unfold the sprayer booms. (Refer to the “Hydraulic Booms” section of this manual for instructions).
8.
Start the sprayer and run at desired RPMs and pressure.
9.
While parked, collect the liquid from the nozzle. Hold a container (Miller Calibration Jar Part
No. 07.11360) graduated in ounces below a nozzle. Record the output for the same time
period as the average driving time determined in step 5. The average output in ounces is
equivalent to the application rate in gallons per acre (GPA).
NOTE: Measuring the output from each tip helps assure balanced spraying from the tips. It will also
help you identify worn tips which may need replacement.
10.
Repeat the procedures for the remaining nozzles.
11.
Compare the actual application rate with the intended rate. If the actual rate varies from the
desired rate, you must adjust the pressure or speed or change tip size to compensate.
Raven Rate Control System (optional)
The rate controller is normally pre programmed from Miller for your sprayer. You should verify that
the programming matches your sprayer specifications. It is very important that the radar gun calibration number is correct. Refer to the Raven owner’s manual.
52
Tank Tie Down Straps
IMPORTANT NOTE: Sprayer tanks will change shape and “Settle In” to the tank saddle when
fully loaded. Retighten the tank tie down straps on all the tanks when the tanks are filled the
first time each year.
Check all the tie down straps for proper tightness.
1.
Fill all tanks completely.
2.
Check the straps for proper tighness. Straps should be snug around the tank.
3.
If straps require tightening, adjust each strap by tightening the hex nut on the appropriate strap
adjusting bolt.
NOTE: Check the tension of the tie down straps periodically during the spraying season and tighten
as required.
Tank Tie Down
Straps
Strap Adjusting
Bolt
Hex Nut
53
Instructions
Valve Settings For Accessory Kits
Refer To The Operator’s Manual For Detailed Instructions
54
Chemical Inductor (Optional)
The 5 gallon Chemical Inductor is an optional accessory and is mounted on the front left corner of
the spray platform. The chemical inductor is used to add chemical to the product tank from ground
level.
DANGER
Handle ALL agricultural chemicals with care. Use chemicals ONLY as directed
on the manufacturer’s warning label.
Wear protective clothing (such as goggles, rubber or chemical resistant gloves
and a respirator) while handling chemicals. Keep protective clothing clean and
in good condition or discard.
Wash hands and face thoroughly with clean water after handling chemicals.
Never eat, smoke, drink or put hands to mouth before washing.
Follow these procedures to properly use the chemical induction system:
1.
Sprayer product tank MUST have at least 50 gallons of water.
2.
Check that the emergency shut off valve located under the product tank is OPEN.
3.
Start the product pump and run at rated speed.
4.
OPEN the Chemical Fill Control valve.
5.
If you are going to use the measuring marks on the chemical inductor tank to measure the
amount of chemical being added, make sure the valve on the bottom of the chemical inductor
tank is CLOSED. Add desired amount of chemical, then OPEN the valve at the bottom of the
chemical inductor tank. The chemical will be transferred from the chemical inductor tank to the
product tank.
NOTE: Poly tanks can vary in size and expand and contract from hot to cold weather. It is not
recommended to use the measuring marks on the chemical inductor tank for precise measuring.
If you do not need to use the chemical inductor tank to measure, you can OPEN the valve at the
bottom of the chemical inductor tank prior to adding the chemical. The chemical inductor will transfer the chemical to the product tank as you are filling.
Chemical Inductor
Tank Cover
Chemical Fill
Control Valve
Chemical Inductor
Tank
Close This Valve To
Measure Chemical
55
6.
When transfer is complete, use the hand rinse gun to rinse the chemical inductor tank. Allow
the rinse water to go through the chemical inductor into the product tank.
NOTE:
•
If the hand rinse gun is supplied with water from the product pump, the water will come
from the product tank and will be contaminated with diluted chemical.
•
If the hand rinse gun is supplied with water from the optional 12 volt electric pump, the
water will come from the rinse tank.
7.
Always turn the valve under the chemical inductor tank OFF before turning the “Chemical Fill”
valve OFF.
8.
Replace the chemical inductor tank lid.
9.
Fully OPEN the “Agitation” valve and allow the product pump to run long enough to thoroughly
mix the product tanks contents.
Hand Rinse Gun
Chemical Inductor
Tank Cover
Chemical Fill
Control Valve
Chemical Inductor
Tank
Chemical Inductor
Venturi
Agitation Control
Valve
Valve At Bottom
Of Inductor Tank
56
NOTE: Some chemicals tend to foam when agitated. If foaming occurs, throttle back the agitation
valve until the foaming stops. If you change the agitation valve setting, you may have to adjust the
pressure on the tractor control box. This adjustment would not be necessary with a RAVEN rate
controller.
NOTE: There are anti foaming agents available:
•
Part No. 07.06881 Shakedown, Liquid - 1 Pint
•
Part No. 07.06880 Shakedown, Dry - 1/2 lb. jar
•
Part No. 07.06879 Shakedown, Water Soluble Packets - 30 per case
10.
If you are mixing more than one chemical into the product tank, you should check with your
chemical supplier to make sure you add the chemicals in the correct sequence to insure
proper mixing.
11.
Be certain to clean and dispose of empty chemical containers properly. Follow the instructions
on the container.
NOTE: DO NOT use the chemical inductor system for powder type chemicals. Flowable granular
chemicals are acceptable.
IMPORTANT: The “Tee” fitting at the bottom of the chemical inductor is a special fitting with
a venturi nozzle on the inside. NEVER operate the chemical inductor without the venturi
nozzle installed.
Standard Control Box
Pressure Adjust Switch
Pressure Gauge
57
Hand Rinse Gun for Chemical Inductor (Optional)
The chemical inductor is supplied with a hand gun with approximately 5 feet of hose to rinse the
chemical inductor tank.
There are two ways the hand gun can be supplied with water:
•
Standard system via the product pump
•
Optional electric system via a 12 volt electric pump
Standard System
•
The standard system supplies water from the sprayer tank via the product pump and has an
ON/OFF valve located at the top of the control center. The control center is located at the front
of the sprayer.
•
The water supplied will be contaminated with diluted mixed chemical.
To Operate:
1.
Start the product pump. Be certain to have water in the product tank and the emergency shut
off valve under the product tank is open.
2.
Open the ON/OFF valve located at the top of the control center.
3.
Remove the hand gun from the storage bracket and rinse the chemical inductor tank.
4.
When finished close the ON/OFF valve, point the hand gun into the chemical inductor tank and
squeeze the trigger to drain the pressure from the hand gun and hose.
5.
Replace the hand gun to the storage bracket and replace the lid on the chemical inductor tank.
58
Optional Electric System
•
The optional electric system has a 12 volt pump located under the 50 gallon rinse water tank.
•
There is an electric ON/OFF switch located at the top of the control center.
•
The water is supplied from the 50 gallon rinse water tank.
To Operate:
1.
There must be water in the 50 gallon rinse water tank.
2.
Turn ON the electric switch located at the top of the control center.
3.
Remove the hand gun from the storage bracket and rinse the chemical inductor tank.
4.
When finished turn OFF the electric switch, point the hand gun into the chemical inductor tank
and squeeze the trigger to drain the pressure from the hand gun and hose.
5.
Replace the hand gun to the storage bracket and replace the lid on the chemical inductor tank.
NOTE: There is a filter assembly located on the electric 12 volt pump. This filter should be serviced
at least once per season. Rinse tank must be empty to remove filter.
Hand Rinse Gun
Storage Bracket
Chemical Inductor
Tank
59
Personal Fresh Water Tank
For your safety all Miller sprayers have a personal 5 gallon fresh water tank as standard equipment.
The fresh water tank is an intregal part of the product tank. This tank is a source for clean, chemical
free water for washing hands or other personal use. Use a water hose to fill the tank with clean
water from an uncontaminated source.
External Sight Gauge (Optional)
An external sight gauge is available for the product tank of your sprayer. This sight gauge is a clear
tube mounted to the product tank on the front side. This gauge is visible from the operators position
and is used as an indicator as to how much water is left in the tank. This gauge indicates the
amount of water in the tank by volume only. It does not indicate gallons.
NOTE: If the external sight gauge tube becomes discolored, it can be replaced by ordering
Part No. 07.13402 (order per foot) from your local Miller dealer.
Personal Fresh
Water Tank Fill
Personal Fresh
Water Tank
Product Tank
Personal Fresh Water
Tank Petcock
External Sight
Gauge
60
Rinse Tank Flush System (Optional)
A 50 gallon fresh water rinse system is an optional accessory. The major components consist of:
•
A 50 gallon clean water tank located on the right side of the sprayer.
•
Three way ball valve located on the left side of the sprayer under the operator platform.
•
ON/OFF valve located at the front of the sprayer on the control stand.
•
(3) rinse balls located in the product tank.
The rinse system can do two different functions:
•
Rinse the product pump, controls and boom lines and leave the product tank undisturbed.
•
Rinse the product pump, product tank, controls and boom lines.
There are two types of control systems available for the rinse system:
•
Manual controls located on the sprayer - Standard
•
Electric controls located on the tractor - Optional
Rinse Tank Fill Valve
Product Tank Rinse
Valve
Product Tank Fill
Valve
Chemical Fill Valve
61
Manual Control System
Filling The Rinse Tank
The 50 gallon rinse tank can be filled 3 different ways:
Fill Through Top Lid
1.
Remove the lid from the top of the rinse tank. Fill the tank using a garden hose or similiar
means.
2.
Replace the lid when complete.
Filling With Transfer Pump
Your sprayer is equipped with a 2" male fast fill connector and a ON/OFF valve (identified as “Valve
F”) located on the left side of the sprayer, directly behind the step.
Fill as follows:
1.
Connect the fill hose to the 2" connector.
2.
Charge the fill hose with water using the transfer pump.
F
OFF
RINSE
TANK
E
PRODUCT
TANK
ON
OFF
3.
Turn the manual three way ball valve identified as “Valve E” (located under platform on left side
of sprayer) to “Rinse Tank” (Point handle forward).
4.
Slowly open the “Fast Fill” valve marked as “Valve F” and let run until rinse tank is full. Turn
off “Fast Fill” valve. There is a breather hose on the rinse tank to allow air to escape.
IMPORTANT: If you are filling with a high volume transfer pump, be careful NOT to open the
“Fast Fill” valve to full flow.
5.
Disconnect the fill hose and replace the dust cap. Be careful removing the fill hose from the
connector - there could be some liquid in the line.
Filling With Sprayer Pump
Your sprayer has the ability to fill the clean water rinse tank its self by using the sprayer product
pump.
Your sprayer is equipped with a 2" male fast fill connector and a ON/OFF valve (identified as “Valve
F”) located on the left side of the sprayer, directly behind the step.
62
Fill as follows:
1.
Connect the fill hose to the 2” connector.
2.
Open the water supply valve to fill the hose.
IMPORTANT: The water source MUST be higher than the sprayer pump. NEVER run the
sprayer pump dry. The sprayer pump will not draw water from a source lower than the
pump, until the pump is primed.
3.
Turn the manual 3 way ball valve identified as “Valve E” (located under platform on left side of
sprayer to the “OFF” position (Point handle down).
4.
Open the “Fast Fill” valve marked as “Valve F.”
5.
Start the product pump and run at full capacity.
6.
Slowly open the “Rinse Tank” valve marked as “Valve A” located on the front control stand
and let run until the rinse tank is full. Turn off the “Rinse Tank Fill” valve. There is a breather
hose on the rinse tank to allow air to escape.
7.
Stop the product pump.
8.
Return the 3 way ball valve to the desired position (“Rinse Tank” or “Product Tank”).
9.
Close the “Fast Fill” valve.
10.
Shut off the external water source.
11.
Disconnect the fill hose and replace the dust cap. Be careful removing the fill hose from the
connector - there could be some liquid in the line.
Valve A
63
Electric Control System
Filling The Rinse Tank
The 50 gallon rinse tank can be filled 3 different ways:
Fill Through Top Lid
1.
Remove the lid from the top of the rinse tank. Fill the tank using a garden hose or similiar
means.
2.
Replace the lid when complete.
Filling With Transfer Pump
Your sprayer is equipped with a 2" male fast fill connector and a ON/OFF valve (identified as “Valve
F”) located on the left side of the sprayer, directly behind the step.
Fill as follows:
1.
Connect the fill hose to the 2" connector.
2.
Charge the fill hose with water using the transfer pump.
F
OFF
RINSE
TANK
E
PRODUCT
TANK
ON
OFF
3.
Locate the electric rinse control switch on the control box on the tractor. Move the switch to
“Rinse Water” or “Rinse Tank” (depending on which control switch your sprayer has).
4.
Slowly open the “Fast Fill” valve marked as “Valve F” and let run until rinse tank is full. Turn
off “Fast Fill” valve. There is a breather hose on the rinse tank to allow air to escape.
IMPORTANT: If you are filling with a high volume transfer pump, be careful NOT to open the
“Fast Fill” valve to full flow.
5.
Disconnect the fill hose and replace the dust cap. Be careful removing the fill hose from the
connector - there could be some liquid in the line.
Filling With Sprayer Pump
Your sprayer has the ability to fill the clean water rinse tank its self by using the sprayer product
pump.
Your sprayer is equipped with a 2" male fast fill connector and a ON/OFF valve (identified as “Valve
F”) located on the left side of the sprayer, directly behind the step.
64
Fill as follows:
1.
Connect the fill hose to the 2” connector.
2.
Open the water supply valve to fill the hose.
IMPORTANT: The water source MUST be higher than the sprayer pump. NEVER run the
sprayer pump dry. The sprayer pump will not draw water from a source lower than the
pump, until the pump is primed.
3.
Located under the operator platform on the left side of the sprayer is an electric 3 way ball
valve. Directly behind this valve is a manual ON/OFF valve with a yellow handle. Turn this
valve “OFF” (handle pointed toward rear of sprayer).
4.
Open the “Fast Fill” valve marked as “Valve F.”
5.
Start the product pump and run at full capacity.
6.
Slowly open the “Rinse Tank” valve marked as “Valve A” located on the front control stand
and let run until the rinse tank is full. Turn off the “Rinse Tank Fill” valve. There is a breather
hose on the rinse tank to allow air to escape.
7.
Stop the product pump.
8.
Close the “Fast Fill” valve.
9.
Turn the valve under the platform “ON” (handle pointed toward right side of sprayer).
10.
Shut off the external water source.
11.
Disconnect the fill hose and replace the dust cap. Be careful removing the fill hose from the
connector - there could be some liquid in the line.
Yellow
Handle
Valve A
Electric 3 Way
Ball Valve
65
Cleaning The Sprayer
Keeping your sprayer clean helps assure a long service life. Many pesticides can quickly corrode
metal parts in the spraying system. Chemicals remaining in the sprayer can react with a second
chemical introduced to the system and offset its effectiveness.
Manual Control Rinse System
Short Term Shutdown
Rinsing the Product Pump, Controls and Boom Lines Leaving the Product Tank Undisturbed:
1.
Turn OFF the “Agitation Valve” located on the front control stand - If so desired.
2.
Turn OFF the Self Cleaning Filter valve located at the front left corner of the operator platform If so desired.
Agitation Valve
Self Cleaning
Filter Valve
3.
Turn the manual 3 way ball valve identified as “Valve E” (located under platform on left side of
sprayer) to “Rinse Tank” (Point handle forward).
4.
Start product pump, drive at normal speed, turn complete boom ON and spray as normal until
clean liquid comes out of sprayer tips.
5.
Turn boom OFF, stop the product pump and stop the tractor.
6.
Turn the manual 3 way ball valve identified as “Valve E” (located under platform on left side of
sprayer) to “Product Tank” (Point handle toward rear of sprayer).
F
OFF
RINSE
TANK
E
PRODUCT
TANK
ON
OFF
7.
Turn ON the “Agitation Valve” located on the front control stand - If so desired.
8.
Turn ON the Self Cleaning Filter valve located at the front left corner of the operator platform.
66
Long Term Shutdown
Rinsing the Product Pump, Product Tank, Controls and Boom Lines:
NOTE: It is important to “Triple” rinse the system to insure proper cleaning. The use of a Neutralizer
is recommended for cleaning when changing chemicals.
Part no. 07.06876 Neutralize Liquid (1 gallon) or Part No. 07.06877 Neutralize Dry (2 lb. jar) are
available from your Miller dealer.
1.
Add the recommended amount of Neutralizer to the clean water rinse tank.
2.
Turn the manual 3 way ball valve identified as “Valve E” (located under platform on left side of
sprayer) to “Rinse Tank” (Point handle forward).
3.
Start the product pump and run at full speed.
4.
Open “Valve B” located in the front of the sprayer on the control stand. Let the pump run until
you have used a third of the water in the clean water rinse tank.
5.
Close “Valve B” located in the front of the sprayer on the control stand.
6.
Turn the manual 3 way ball valve identified as “Valve E” (located under platform on left side of
sprayer) to “Product Tank” (Point handle toward rear of sprayer).
7.
Drive at normal speed, turn complete boom on and spray as normal until product tank is
empty.
8.
Repeat the cleaning procedure two more times to ensure proper cleaning.
Valve B
F
OFF
RINSE
TANK
E
PRODUCT
TANK
OFF
67
ON
Electric Control Rinse System
Short Term Shutdown
Rinsing the Product Pump, Controls and Boom Lines Leaving the Product Tank Undisturbed:
1.
Turn OFF the “Agitation Valve” located on the front control stand - If so desired.
2.
Turn OFF the Self Cleaning Filter valve located at the front left corner of the operator platform If so desired.
Agitation Valve
Self Cleaning
Filter Valve
3.
Locate the electric rinse control switch on the control box on the tractor. Move the switch to
“Rinse Water” or “Rinse Tank” (depending on which control switch your sprayer has).
4.
Start product pump, drive at normal speed, turn complete boom ON and spray as normal until
clean liquid comes out of sprayer tips.
5.
Turn boom OFF, stop the product pump and stop the tractor.
6.
Move the electric rinse switch on the tractor control box to the “Product Tank” position.
7.
Turn ON the “Agitation Valve” located on the front control stand - If so desired.
8.
Turn ON the Self Cleaning Filter valve located at the front left corner of the operator platform.
68
Long Term Shutdown
Rinsing the Product Pump, Product Tank, Controls and Boom Lines:
NOTE: It is important to “Triple” rinse the system to insure proper cleaning. The use of a Neutralizer
is recommended for cleaning when changing chemicals.
Part no. 07.06876 Neutralize Liquid (1 gallon) or Part No. 07.06877 Neutralize Dry (2 lb. jar) are
available from your Miller dealer.
1.
Add the recommended amount of Neutralizer to the clean water rinse tank.
2.
Locate the electric rinse control switch on the control box on the tractor. Move the switch to
“Rinse Water” or “Rinse Tank” (depending on which control switch your sprayer has).
3.
Start the product pump and run at full speed.
4.
Locate the electric control switch on the tractor control box and move the switch to “Rinse
Balls” or “Product Tank Rinse” and let run until you have used a third of the water in the clean
water rinse tank.
5.
On the tractor control box, move the “Rinse Balls” switch to the “Product Tank” position (HC
control) and/or “Product Tank Rinse” switch to the “OFF” position and the “Product Tank”/
“Rinse Tank” switch to the “Product Tank” position (Standard electric control).
6.
Drive at normal speed, turn complete boom on and spray as normal until product tank is
empty.
7.
Repeat the cleaning procedure two more times to ensure proper cleaning.
Cleaning Your Sprayer Manually
Keeping your sprayer clean helps assure a long service life. Many pesticides can quickly corrode
metal parts in the spraying system. Chemicals remaining in the sprayer can react with a second
chemical introduced to the system and offset its effectiveness.
Following are instructions for cleaning your sprayer if it is not equipped with a factory installed rinse
system.
1.
Select an area where the cleaning solution can be safely sprayed out of the system.
2.
Check the label on the chemical container for specific cleaning instructions.
3.
Wash the entire sprayer system using a water hose and a brush. Use a soft brush to clean
nozzle tips and screens.
4.
Flush with clean water.
5.
Dispose of the cleaning solution properly according to local regulatory agency requirements.
69
Hydraulic Boom Operation
Three types of hydraulically operated booms are available. They are EF Booms, EFT Booms and
HC Booms.
DANGER
To avoid personal injury or death, KEEP clear of ALL electrical power lines
when operating sprayer or when folding or unfolding booms.
WARNING
To avoid personal injury, make sure that everyone is at a safe distance from the
sprayer before folding or unfolding the sprayer boom. Keep a safe distance
from the boom while in operation. Hydraulic booms may move suddenly
without warning.
EF & EFT Boom
After the sprayer and hydraulic hoses have been properly attached to the tractor, unfold the boom
using the following procedure:
1.
Raise the complete boom until the boom wings clear the transport rest.
2.
Place the tractor in park and/or set the brakes and stop the engine.
3.
Remove the transport lock from the lift cylinder at the rear of the sprayer and place in the
storage position provided.
4.
Restart the tractor and unfold the boom wings until the boom is in the working position.
5.
Lower the entire boom to the desired height.
IMPORTANT: DO NOT lower boom to the full down position. There must be a minimum of 11/2” of hydraulic lift cylinder shaft showing before the suspension can work properly.
Transport Lock
Hydraulic Lift
Cylinder
70
EFT Boom
After the sprayer booms have been unfolded and lowered to the correct height, tilt the boom wings
using the following procedure:
1.
Flip the wing tilt switch on the control box to the tilt position.
2.
Using the tractor hydraulic controls tilt the individual wings up or down to the desired position.
a. The tractor control for the single hose control will tilt the left wing.
b. The tractor control for the dual hose control will tilt the right wing.
Wing Tilt Switch
Fold the boom using the following procedure:
NOTE: For EFT booms, level both boom wings before proceeding.
1.
Raise the boom to the full lift height.
2.
Fold the boom inward until the boom is over the top of the transport rest.
3.
Place the tractor in park and/or set the brakes and stop the engine.
4.
Remove the transport lock from the storage position on the boom stabilizer arm and put in
place on the hydraulic lift cylinder.
5.
Restart the tractor and lower the boom on to the boom transport rest.
Transport Lock In Storage Position On
Boom Stabilizer Arm
71
HC Boom
The HC Boom uses five separate hydraulic cylinders which allow the operator maximum control of
the boom. Boom components are controlled independently with the boom control box mounted on
the tractor.
The switches on the control box operate the following boom functions:
•
The MID SECTION control raises or lowers the complete boom.
•
The two FOLD controls fold the respective wings IN or OUT depending on the position of the
switch.
•
The RIGHT and LEFT controls tilt their respective wing UP or DOWN.
Control Box
Left Side Control
Switches
Mid Section
Control Switch
Right Side Control
Switches
The HC Boom controls are designed for a tractor with a open or closed center hydraulic system.
Refer to page 19 “HC Boom Hydraulic Hose and Electrical Connections” for a detailed explanation
of the hydraulic settings.
Whenever the HC boom is in use, the tractor hydraulic valve on the tractor MUST be locked open to
assure a constant supply of oil to the cylinder valve control bank at the back of the sprayer.
Cylinder Valve
Control Bank
72
Lubrication
WARNING
Before attempting any lubrication, adjustment or servicing of the sprayer, be
sure to shut down the sprayer and lock out the power source. Contact with
moving parts or hydraulic fluid under pressure can cause death or personal
injury.
WARNING
DO NOT adjust or lubricate the machine while it is in motion. ALWAYS shut
off the tractor first.
WARNING
ALWAYS securely block the sprayer up when servicing requires working
under it.
Daily Lubrication Interval
PTO Shaft
There are a total of 8 grease fittings on the PTO assembly.
Grease with a high quality grease before starting work each day or after every 8 hours of operation.
Clean and grease PTO shaft before each prolonged period of nonuse.
Grease the shield tubes to prevent seizing.
Follow any other service instructions from the manufacturer.
Grease Fittings
Grease Fittings
Grease Fittings
PTO Shaft
Grease Fittings
Sprayer Pump
WARNING
ALWAYS replace any shielding after any servicing or lubrication of the pump.
NEVER operate the sprayer unless ALL shielding is in place and secure. Contact with rotating parts can cause death or personal injury.
Your sprayer may be equipped with one of several pumps. To help assure proper lubrication, refer
to the pump owner’s manual for detailed lubrication information
73
Weekly Lubrication Interval
EF & EFT Boom Primary and Secondary Boom Pivot Points
Lubricate ALL the pivot points on each side of the boom assembly using a good quality grease.
Clean off grease fittings before attaching grease gun. Wipe up any excess grease when finished.
NOTE: There are a total of 9 grease fittings on the EF boom assembly and 11 grease fittings on the
EFT boom assembly.
Boom Pivots
Upper
Grease Fittings
Boom Pivots
Lower EFT Boom
Boom Pivots
Lower EF Boom
Grease Fittings
Grease Fittings
Boom Pivots
Secondary Boom
Grease Fittings
74
EF & EFT Boom Center Boom Mounting Arm Pivot Points
Lubricate ALL the pivot points on each mounting arm and the center pivot using a good quality
grease. The center pivot is located directly behind the slow moving vehicle (SMV) emblem. Clean
off grease fittings before attaching grease gun. Wipe up any excess grease when finished.
Boom Pivot Center
Grease Fitting
Grease Fittings
Mounting Arm Pivots
(Left and Right Sides)
75
HC Boom
Lubricate ALL the pivot points on each side of the boom assembly using a good quality grease.
Clean off grease fittings before attaching grease gun. Wipe up any excess grease when finished.
Secondary Boom
Wing Pivot Point
Grease Fittings (three at top and
one at lower pivot on each side)
Boom Pivots (three on
each side of sprayer)
Boom Tower Slides (HC Boom Only)
Weekly lubricate the boom tower slides with liquid graphite.
If operating in extremely dusty conditions, shorten the
lubrication interval as required.
Boom Tower Slides
76
200 Hour Lubrication Interval
Wheel Bearings
Every 200 hours (or yearly), repack the wheel bearings using a good quality wheel bearing grease.
Maintenance
General
Repair or replace damaged or broken parts immediately.
Check all safety and operating decals. If any decals are illegible or missing, replace any decals
immediately. DO NOT operate sprayer with missing or damaged decals. Refer to the “Safety
Decal” section of this manual for all safety decal locations. Refer to your parts manual for all operating decals.
Fasteners
After the first hour of use, check all the fasteners and tighten any found to be loose. Thereafter,
check all fasteners periodically and tighten as required.
Tire Pressure
Check the tire pressure daily.
The recommended tire pressure is:
12.4-24 6 ply tires .............................. 24 psi
11.2-38 4 ply tires .............................. 18 psi
Filters
Remove and clean the water filters daily. Clean the filters on the optional foam marking system at
intervals as specified in the foam system owner’s manual.
IMPORTANT: Always wear gloves and eye protection while servicing the sprayer.
To manually clean the self cleaning filter:
1.
Make sure the product pump is turned OFF.
2.
Close the emergency shut off valve under the product tank.
3.
Make sure the agitation valve and self cleaning filter bypass agitation valve are both closed.
4.
Place a clean empty container under the filter base to catch any water and chemicals.
5.
Very carefully disconnect the bypass line from the bottom of the filter and allow the water and
chemicals to flow into the container.
6.
Remove the canister from the filter head by rotating counter clockwise.
7.
Rinse the canister and screen in clean water.
77
8.
Before reinstalling the canister to the filter head, lubricate the canister o-ring with clean engine
oil. Reinstall the canister and hand tighten only.
9.
Connect the bypass hose to the bottom of the filter, open the bypass and agitation valves.
Open the emergency shut off valve at the bottom of the product tank.
10.
Start the sprayer pump with water in the tank and check for leaks.
11.
This procedure also applies to sprayer equipped with the standard filter.
Sprayer Tips
Refer to the information found on page 25 “Spray Tip Wear” for tip cleaning.
Storing and Winterizing
Storing your sprayer properly during the off season will help reduce the time needed to get the
sprayer ready for the next spraying season. If at all possible, store your sprayer in a dry building to
protect it from the harmful effects of the weather. Ultraviolet light in the sun’s rays softens and
weakens rubber used for hoses and tires.
WARNING
Wear protective clothing (such as goggles, rubber or chemical resistant gloves
and a respirator) while handling or working with chemicals. Keep protective
clothing clean and in good condition or discard.
IMPORTANT: It is very important that you thoroughly clean the sprayer inside and out.
Cleaning the Inside of the sprayer
1.
Add about 50 gallons of clean water along with a Neutralizing agent into the sprayer product
tank. Refer to “Cleaning the Sprayer” in this manual.
2.
Start the product pump and run at rated volume.
3.
Open and close ALL valves on the sprayer to ensure you have clean water through the entire
system.
NOTE: The pressure gauge hose is supplied from the rear of the sprayer and is a “dead end” circuit.
The following procedure is recommended for cleaning.
a. With the sprayer pump turned off, carefully remove the pressure line from the bottom of the
pressure gauge.
b. Hold the end of the hose above a bucket and have an assistant start the sprayer pump
momentarily at an idle ONLY. Leave run at idle until clean liquid comes out of the hose.
Be careful of any “splash back” in the bucket.
c. Stop the sprayer pump and reattach the hose to the gauge.
4.
Spray liquid out through the boom at a proper location. Manually drain as much water as
possible. Dispose of liquid properly.
5.
Check entire sprayer for worn or damaged components. Replace as necessary.
78
6.
Add approximately 20 gallons of environmentally safe antifreeze suitable for the climate in your
area.
7.
Start the product pump and run at rated volume.
8.
Open and close ALL valves on the sprayer to ensure you have clean antifreeze through the
entire system.
NOTE: The pressure gauge hose is supplied from the rear of the sprayer and is a “dead end” circuit.
The following procedure is recommended for winterizing.
a. With the sprayer pump turned off, carefully remove the pressure line from the bottom of the
pressure gauge.
b. Hold the end of the hose above a bucket and have an assistant start the sprayer pump
momentarily at an idle ONLY. Leave run at idle until clean antifreeze comes out of the
hose. Be careful of any “splash back” in the bucket.
c. Stop the sprayer pump and reattach the hose to the gauge.
9.
Turn on the boom until antifreeze begins spraying from the spray tips. Shut off the sprayer and
let the antifreeze remain in the system.
Chemical Inductor
Be sure to drain the chemical inductor system, flush with clean water then run environmentally safe
antifreeze (RV antifreeze) through the system. Open all inductor valves to insure antifreeze has
been run through the entire inductor system.
Foam Marker
IMPORTANT: The liquid lines and tank must be drained completely prior to storage. If liquid
in this system is allowed to freeze, several components may be damaged.
1.
Remove the in-line filter bowl at the bottom of the tank and flush tank with warm water.
2.
Replace the filter bowl. Fill the tank with at least 2 gallons of hot water. Turn on the machine
and allow to run out each side until no foam is generated. Repeat if necessary.
3.
Add RV type antifreeze to the tank. Do not use windshield washer fluid because it can clog
the foamer.
4.
Turn on machine until antifreeze solution reaches each foamhead.
5.
Check the air and liquid lines for holes and replace as required. Be sure to flush and drain all
liquid from the system prior to storage in freezing temperatures.
Cleaning the outside of the sprayer
1.
Thoroughly clean the outside of the sprayer with soap and water until all surfaces are clean. A
high pressure washer would help this process.
2.
Paint all scratched or rusty surfaces.
3.
Check all safety decals, reflectors and lights that they are in good condition and function
properly. Replace or repair as needed.
4.
Grease and lubricate all fittings and slide areas. Refer to the “Lubrication” section of this
manual.
79
Boom Adjustments
HC Boom Only
Boom Slides
The poly slides on the boom tend to wear over time. Adjust the pressure on the poly slides as
needed to compensate for wear.
To adjust the pressure on the poly slide pads, locate the large locknuts (located by each pad) on the
tank side of the slide tower. Tighten the locknuts to increase the pressure on the poly slide pads.
Tighten all the pads equally.
Boom Breakaways
The tension of the boom breakaways should be checked and adjusted as needed. If the tension on
the breakaways is too great, the boom may be damaged if it strikes a stationary object. Tightening
the nuts on the extension spring for the breakaway increases the tension. Turning the nuts out
decreases the tension. The springs are located between the primary and secondary boom wings.
Boom Level
If the boom does not hang level, secure the boom with an overhead hoist or other suitable means.
Loosen the six nuts on the bolts which hold the boom to the tower slides. These bolts fit through
slotted holes. Level the boom and retighten the nuts.
Boom Wing Alignment
Align boom inner and outer wings with the parallel connecting link. Remove the pin from the clevis
on the end of the link. Turn the clevis in or out on the threaded shaft intil the link is properly aligned.
Reinstall the pin.
Tower Slides
Boom Level Adjustment
Bolts (Three Per Slide)
Extension Springs
Spring Anchor
Adjustment Nuts
80
EF & EFT Boom Only
Boom Level
If the entire boom is not level side to side adjust the threaded rod and spring assembly at the rear of
the center boom. Tighten the locknuts after adjustment is complete.
Threaded Rod and
Spring Assembly
Boom Wing Assembly Alignment
If the wing assemblies are not aligned (up or down), the wing assemblies can be raised or lowered.
Secure the boom wing assembly with an overhead hoist or other suitable means. Loosen the four
nuts at the pivot between the center boom and the primary boom wing. Use the overhead hoist to
level the boom wing assembly. Tighten the four nuts securely.
Boom Wing Level
Adjustment Nuts
Boom Wing Level
Adjustment Nuts
81
EF & EFT Boom (continued)
Boom Wing Fold Out Adjustment
If the secondary boom wings do not unfold properly, with the boom in the folded position, adjust the
turnbuckle at the rear of the primary boom wing until the cable is tight. Recheck the boom
breakaway tension and adjust if necessary.
Boom Fold Out
Turnbuckle
Boom Breakaways
The tension of the boom breakaways should be checked and adjusted as needed. If the tension on
the breakaways is too great, the boom may be damaged if it strikes a stationary object. Adjust the
tension as needed by turning the turnbuckles located on the front side of the boom wings (when
boom is completely unfolded). Adjust as required. Tighten the locknuts against the turnbuckle when
complete.
Boom Breakaway
Turnbuckle
82
Troubleshooting Guides
Following are troubleshooting guides to help you solve common operating problems. If you have
difficulty resolving operating problems, call your dealer for assistance.
Problem
No pressure in spray
system
Possible Cause
Air leak in suction line
Dirty or clogged filter
Kinked hose
Pump not primed
Water not flowing from tank
Spray system pressure
low
Erratic spray system
pressure
Solution
Tighten clamps, check hoses for
cracks or breaks
Clean filter
Straighten hose, route hose for
gradual bends
Prime pump (see priming pump
and pump owners manual)
Empty tank; refill
Check tank outlet; clear debris if
any
Make sure emergency shut off
valve is open
Make sure throttling valve is
open
Pump is defective; repair or
replace
Primary filter beginning to plug
Pressure regulating or throttling valve
out of adjustment
Spray tips to large
Speed to slow
Pump running to slow
Clean filter
Adjust valve
Air leaks in suction line
Tighten clamp; check hoses for
cracks or breaks
Refill tank
Remove tank cover; clean tank
vent
Tank getting empty
Vacuum developing in tank
Verify spray tip size
Increase travel speed
Increase pump speed
Spray system pressure
can’t be regulated
Pressure regulating valve not working
Check electric wiring to valve;
tighten electrical connections
Replace valve if defective
Spray system pressure
increasing
Tips plugging
Tip screens plugging
In line filter plugging
Clean tips
Clean screens
Clean in line filter
Application rate to low
Sprayer not calibrated properly
Speed sensor not calibrated correctly
Spray tip to small
Calibrate sprayer
Calibrate speed sensor
Verify spray tip size
83
Troubleshooting Guides (continued)
Problem
Possible Cause
Solution
RAVEN Controller
No speed reading
Blown out fuse
Poor wire connection or bad wire
Check and replace fuse
Clean and check connection
Check for break in wire
Speed reading to slow or
to fast
Wrong calibration number
SP-1 or SP-2 setting wrong
SP-1 Wheel drive
SP-2 Radar gun
Verify calibration number
Verify setting - See RAVEN
owners manual
No rate in rate window
Flow meter not working
Check connections and wires
Check for foreign material in rotor
Check transducer
See RAVEN owners manual for
instructions
Rate will not change or
adjust
Regulating valve not working
Check connections and wiring
Check for foreign material in
valve
See RAVEN owners manual for
instructions
Nozzle output not equal
Tips plugging
Tip screens plugging
In line filter plugging
Nozzle check valve sticky or swollen
Clean tips
Clean screens
Clean in line filter
Clean or replace check valve
Boom section output not
equal
ON/OFF valve not opening completely
Clean or replace ON/OFF valve
Boom section will not turn
on
No signal from control box
Check connections and wires for
breaks
Unplug ON/OFF valve connection on sprayer for one minute
and replug
Circuit breaker released in ON/OFF
boom ball valve
Poor tank agitation
Hydraulic drive pump
keeps stopping
Agitation valve closed
Agitation valve not completely open
Self cleaning filter ON/OFF valve not
open
Plugged agitation nozzle(s)
Open valve
Open valve
Open valve
To much oil flow from tractor
Reduce oil flow from tractor
See pump owners manual for
details
84
Clean nozzles
Troubleshooting Guides (continued)
Problem
Possible Cause
Solution
EF & EFT Boom
Boom bounces excessively
Low pressure in accumulator
Field to rough
Weak shock absorber
See dealer for service
Slow down
Replace shock absorber
Boom settles
Bad seals in lift cylinder
Tractor hydraulic valve leaks
Replace seals
Replace seals in valve
Boom not level
Coil spring out of adjustment
Boom wing sagging
Adjust coil spring
Adjust top boom wing support
Boom bounces excessively
Weak S-Tine(s)
Weak shock absorbers
Field to rough
Tower slides out of adjustment or worn
Replace S-Tine(s)
Replace shock absorbers
Slow down
Adjust tower slide and/or replace
Boom not level
Tower slides out of adjustment
Adjust tower slide
Boom settles or creeps up
Bad cylinder seals
Dirt in HC valve block spool
Replace seals
Clean spool
HC Boom
85
Torque Specifications
NOTE: Use these torque values when tightening hardware (excluding: locknuts and self tapping,
thread forming and sheet metal screws) unless specified otherwise.
All torque values are in lb-ft except those marked with an (*) which are lb-in (for metric torque value
Nm, multiply lb-ft value by 1.355 or for lb-in multiply by 0.113).
Unified
Grade 2
Grade 5
Grade 8
National Thread
Dry
Lubed
Dry
Lubed
Dry
Lubed
8-32
8-36
19*
20*
14*
15*
30*
31*
22*
23*
41*
43*
31*
32*
10-24
10-32
27*
31*
21*
23*
43*
49*
32*
36*
60*
68*
45*
51*
1/4-20
1/4-28
66*
76*
50*
56*
9
10
75*
86*
12
14
9
10
5/16-18
5/16-24
11
12
9
9
17
19
13
14
25
25
18
20
3/8-16
3/8-24
20
23
15
17
30
35
23
25
45
50
35
35
7/16-14
7/16-20
32
36
24
27
50
55
35
40
70
80
55
60
1/2-13
1/2-20
50
55
35
40
75
90
55
65
110
120
80
90
9/16-12
9/16-18
70
80
55
60
110
120
80
90
150
170
110
130
5/8-11
5/8-18
100
110
75
85
150
180
110
130
220
240
170
180
3/4-10
3/4-16
175
200
130
150
260
300
200
220
380
420
280
320
7/8-9
7/8-14
170
180
125
140
430
470
320
360
600
660
460
500
1-8
1-14
250
270
190
210
640
710
480
530
900
1000
680
740
Metric
Grade 8.8
Grade 10.9
8.8
10.9
Grade 12.9
12.9
Course Thread
Dry
Lubed
Dry
Lubed
Dry
Lubed
M6-1
M8-1.25
M10-1.5
M12-1.75
M14-2
M16-2
8
19
37.5
65
103.5
158.5
6
14
28
48
76.5
117.5
11
27
53
91.5
145.5
223.5
8
20
39
67.5
108
165.5
13.5
32.5
64
111.5
176.5
271
10
24
47
82
131
200
86
Tightening Hydraulic Fittings
CAUTION
Escaping fluid under pressure can penetrate the skin causing serious injury.
Relieve pressure before disconnecting hydraulic or other lines. Tighten all
connections before applying pressure. Keep hands and body away from pin
holes and nozzles which eject fluids under high pressure. Use a piece of
cardboard or paper to search for leaks. DO NOT use your hand.
Tightening O-Ring Fittings*
1.
Torque Value*
Recommended
Turns To
Tighten
(After Finger
Tightening)
(In.)
(Nm)
(lb-ft)
(Flats) (Turns)
3/8
1/2
8
6
2
1/3
7/16
9/16
12
9
2
1/3
1/2
5/8
16
12
2
1/3
Position angle fittings by unscrewing no
more than one turn.
9/16
11/16
24
18
2
1/3
3/4
7/8
46
34
2
1/3
Tighten straight fittings to torque shown.
7/8
1
62
46
1-1/2
1/4
1-1/16
1-1/4
102
75
1
1/6
1-3/16
1-3/8
122
90
1
1/6
1-5/16
1-1/2
142
105
3/4
1/8
1-5/8
1-7/8
190
140
3/4
1/8
1-7/8
2-1/8
217
160
1/2
1/12
Inspect O-ring and seat for dirt or obvious
defects.
2.
On angle fittings, back the locknut off until
washer bottoms out at top of groove.
3.
Hand tighten fitting until backup washer or
washer face (if straight fitting) bottoms on
face and O-ring is seated.
4.
5.
* Torque values shown are based on lubricated
connections as in reassembly.
Thread
Size
Nut Size
Across
Flats
(In.)
Tightening Flare Type Fittings*
1.
Recommended
Turns To
Tighten
(After Finger
Tightening)
Check flare and flare seat for defects that
might cause leakage.
Tube
Size
OD
Nut Size
Across
Flats
2.
Align hose end with fitting before tightening.
(In.)
(In.)
(Nm)
(lb-ft)
3/16
7/16
8
6
1
1/6
3.
Lubricate connection and hand tighten
swivel nut until snug.
1/4
9/16
12
9
1
1/6
5/16
5/8
16
12
1
1/6
4.
To prevent twisting the hose, use two
wrenches. Place one wrench on the hose
end body and with the second wrench,
tighten the swivel nut to the torque shown
in this chart.
3/8
11/16
24
18
1
1/6
1/2
7/8
46
34
1
1/6
5/8
1
62
46
1
1/6
3/4
1-1/4
102
75
3/4
1/8
7/8
1-3/8
122
90
3/4
1/8
* Torque values shown are based on lubricated
connections as in reassembly.
87
Torque Value*
(Flats) (Turns)
Optional Accessories
In Line Filter Kit
The In Line Filter Kit is an optional accessory.
The in line filters are located on the mid section of the boom and are attached to the ON/OFF valves.
There will be one filter per ON/OFF valve and are equipped with 50 mesh screens. Optional size
screens are available through your Miller parts dealer.
WARNING
Wear protective clothing (such as goggles, rubber or chemical resistant gloves
and a respirator) while handling or working with chemicals. Keep protective
clothing clean and in good condition or discard.
To clean screens:
1.
Use caution when removing filter canisters or boom lines. There could be residual pressure in
the filter or boom lines.
2.
Place a container under the filter canister.
3.
SLOWLY loosen and remove the drain plug from the bottom of the canister and let filter drain
completely.
4.
Unscrew the filter canister, remove the screen and rinse in clean water.
5.
Wipe the inside of the canister with a clean rag.
6.
Lightly oil the o-rings on the filter canister and the drain plug.
7.
Reassemble the filter screen into the canister and the canister to the filter head. DO NOT over
tighten.
8.
Reinstall the drain plug into the canister. DO NOT over tighten.
9.
Dispose of the waste material properly.
88
Fence Line Kit(s)
The fence line kit(s) are an optional accessory.
There are three different styles of fence row kits available:
•
Manual ON/OFF valve
•
Electric solenoid ON/OFF valve
•
Electric Ball ON/OFF valve
You may order a fence line nozzle for the left, right or both sides of the boom. (right side is the most
common).
Manual Fence Row Nozzle Operation:
1.
Before operating sprayer, with the boom unfolded, adjust the spray body to the desired position
(located at end of spray boom).
2.
With the spray boom turned OFF walk to the end of the boom and turn ON the fence row
nozzle valve. When handle is at a right angle from the valve it is in the OFF position.
3.
Start the sprayer and spray as normal.
4.
When finished turn OFF the boom, stop the tractor and walk to the end of the boom and turn
OFF the fence row nozzle valve.
5.
Resume spraying as normal.
Electric Fence Row Nozzle Operation:
1.
Before operating sprayer, with the boom unfolded, adjust the spray body to the desired position
(located at end of spray boom).
2.
Locate the electric switch marked “Fence Row” located on the sprayer control panel.
3.
This switch can be turned ON or OFF at any time. You will have the ability to spray with this
nozzle if the boom is turned ON or OFF.
NOTE: The Electric Fence Row Nozzle is supplied with a non drip check valve to prevent the line
from draining.
89
WARRANTY
MILLER-ST. NAZIANZ, INC. warrants each new Miller Trailer Sprayer to be free from defects in
material and workmanship under recommended use and service, as stated in the Operator’s Manual,
as follows:
1. Base Warranty. Miller will replace, F.O.B. St. Nazianz, Wisconsin, or repair, as Miller elects,
any part of a new Miller Trailer Sprayer which is defective in material or workmanship:
(a)
(b)
without charge for either parts or labor during the first year
following delivery to the original retail customer; and
without charge for parts only (not labor) during the second
year following delivery to the original retail customer.
Items not manufactured by Miller (pumps, tanks, controls, monitors, etc.) for the second year
will be subject to its own manufacturer’s warranty policy.
Notwithstanding the above, Miller does not warrant tips and nozzle bodies against wear and
breakage as these items are expected to wear and extent of wear or breakage depends on
operating practices.
All warranties on the new Miller Trailer Sprayer shall apply only to the original retail purchaser from an
authorized Miller dealer.
Repair Parts
Miller warrants that it will replace, F.O.B. St. Nazianz, Wisconsin, or repair, as Miller elects, without
charge, any genuine Miller Sprayer spare part purchased after the expiration of the new Sprayer
warranty, or to any subsequent owners, that is defective in material or workmanship, within ninety (90)
days of the installation date.
Misuse
The provisions of this warranty shall not apply to any Miller Sprayer which has been subject to misuse,
negligence, alteration or accident, or which shall have been repaired with parts other than those
obtainable through Miller.
Authorized Dealer
Repairs eligible for labor warranty must be made by Miller or an authorized Miller dealer. The purchaser
is responsible for transportation of the equipment to the dealership for warranty service or for any
service call expense.
Exclusive Effect of Warranty and Limitation of Liability
The remedies of the customer set forth herein are exclusive. Miller neither assumes nor authorizes any
person to assume any other obligation or liability in connection with the sale of covered equipment.
Correction of defects and malfunctions in the manner and for the applicable period of time provided
above, shall constitute fulfillment of all responsibilities of Miller to the customer and Miller shall not be
liable for negligence, under contract, or in any other manner with respect to such equipment. IN NO
EVENT SHALL THE OWNER BE ENTITLED TO RECOVER FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES SUCH AS BUT NOT LIMITED TO. LOSS OF CROPS, LOSS OF
PROFITS OR REVENUE, OTHER COMMERCIAL LOSSES, INCONVENIENCE OR COST OF
RENTAL OF REPLACEMENT EQUIPMENT.
THIS WARRANTY IS IN LIEU OF ALL WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PURPOSE OR OTHER WARRANTIES, EXPRESS OR IMPLIED.
Warranty Requirements
To be covered by warranty, each machine must be properly registered with Miller within 30 days of date
of original retail delivery.
© 2007 by Miller-St. Nazianz, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement