MCMC MTSFB TC T011:2014

Add to my manuals
112 Pages

advertisement

MCMC MTSFB TC T011:2014 | Manualzz

MCMC MTSFB TC T011:2014

TECHNICAL CODE

SPECIFICATIONS ON COMMON TEST SUITE FOR

DIGITAL TERRESTRIAL TELEVISION BROADCAST SERVICE

RECEIVER

Developed by Registered by

Registered date: 18 December 2014

© Copyright 2014

MCMC MTSFB TC T011:2014

DEVELOPMENT OF TECHNICAL CODES

The Communications and Multimedia Act 1998 (‘the Act’) provides for Technical Standards Forum designated under section 184 of the Act or the Malaysian Communications and Multimedia

Commission (“the Commission”) to prepare a technical code. The technical code prepared pursuant to section 185 of the Act shall consist of, at least, the requirement for network interoperability and the promotion of safety of network facilities.

Section 96 of the Act also provides for the Commission to determine a technical code in accordance with section 55 of the Act if the technical code is not developed under an applicable provision of the

Act and it is unlikely to be developed by the Technical Standards Forum within a reasonable time.

In exercise of the power conferred by section 184 of the Act, the Commission has designated the

Malaysian Technical Standards Forum Berhad (MTSFB) as a Technical Standards Forum which is obligated, among others, to prepare the technical code under section 185 of the Act.

A technical code prepared in accordance with section 185 shall not be effective until it is registered by the Commission pursuant to section 95 of the Act.

For further information on the technical code, please contact:

Malaysian Communications and Multimedia Commission (MCMC)

Off Persiaran Multimedia

63000 Cyberjaya

Selangor Darul Ehsan

MALAYSIA

Tel: +60 3 8688 8000

Fax: +60 3 8688 1000 http://www.skmm.gov.my

OR

Malaysian Technical Standards Forum Berhad (MTSFB)

4805-2-2, Blok 4805, Persiaran Flora

CBD Perdana 2, Cyber 12

63000 Cyberjaya

Selangor Darul Ehsan

MALAYSIA

Tel: +60 3 8322 1441/1551

Fax: +60 3 8322 0115 http://www.mtsfb.org.my i

MCMC MTSFB TC T011:2014

CONTENTS

Committee Representation ..................................................................................................................... v

Foreword ................................................................................................................................................ vi

1. Scope .................................................................................................................................................. 1

2. Normative References ........................................................................................................................ 1

3. Abbreviations ...................................................................................................................................... 1

4. Requirements ...................................................................................................................................... 3

4.1 RF .................................................................................................................................................. 3

4.2 SI/PSI ............................................................................................................................................. 3

4.3 OAD ............................................................................................................................................... 3

4.4 HbbTV ............................................................................................................................................ 3

5. Malaysia DVB-T2 RF Performance Test Suite Ver1.0 ........................................................................ 4

5.1 Revision History ............................................................................................................................. 4

5.2 Evaluation Details .......................................................................................................................... 4

5.3 Evaluation Results ......................................................................................................................... 4

5.4 Malaysia DVB-T2 RF Modes and Performance Figure ................................................................. 5

5.4.1 RF Profile for Malaysia ......................................................................................................... 5

5.4.2 Performance Figures for Malaysia ....................................................................................... 6

5.5 Test Instrument Set Up .................................................................................................................. 8

5.6 Test Category .............................................................................................................................. 10

5.6.1 Carrier to Noise Ratio (C/N) Performance on Gaussian Channel ..................................... 10

5.6.2 C/N Performance on 0dB Echo Channel ........................................................................... 11

5.6.3 Minimum Receiver Signal Input Levels on Gaussian Channel .......................................... 12

5.6.4 Minimum Integrated Receiver Decoder (IRD) Signal Input Levels on 0db

Echo Channel .................................................................................................................... 13

5.6.5 Maximum Receiver Signal Input Levels ............................................................................. 14

5.6.6 Immunity to "Digital" Signals in Other Channels ................................................................ 15

5.6.7 Immunity to Co-Channel Interference from Analogue TV Signals ..................................... 17

5.6.8 Immunity to Adjacent Channel Interference from Analogue TV Signals ............................ 19

5.6.9 Performance in Time-Varying Channels 10Hz Doppler (5Hz after Automatic

Frequency Control (AFC)) 20μs 0dB Echo........................................................................ 21

5.6.10 Synchronisation for Varying Echo Power Levels in Single Frequency

Networks (SFN) ................................................................................................................. 23

5.6.11 C/(N+I) Performance in SFN for more than one echo ..................................................... 25

5.6.12 C/(N+I) Performance in Single Frequency Networks inside the Guard

Interval (GI) ........................................................................................................................ 27

5.6.13 C/(N+I) Performance in SFN outside the Guard Interval ................................................. 29

6. Malaysia DVB-T2 SI/PSI Conformance Test Suite Ver1.0 ............................................................... 31

6.1 Revision History ........................................................................................................................... 31

6.2 Evaluation Details ........................................................................................................................ 31

6.3 Evaluation Results ....................................................................................................................... 31

6.4 Test Category .............................................................................................................................. 32

6.4.1 Basic SI/PSI Test ............................................................................................................... 32

6.4.1.1 Service Installation and Information ...................................................................... 32 ii

MCMC MTSFB TC T011:2014

6.4.1.2 Event Information .................................................................................................. 33

6.4.1.3 Codec Information ................................................................................................. 35

6.4.1.4 Audio and Subtitle Language ................................................................................ 36

6.4.1.5 Results of Basic SI/PSI Test ................................................................................. 38

6.4.2 Logical Channel Numbering (LCN) Test ............................................................................ 38

6.4.2.1 Decoding of LCN descriptors ................................................................................ 39

6.4.2.2 Foreign Services .................................................................................................... 41

6.4.2.3 No LCN Descriptor ................................................................................................ 42

6.4.2.4 Regional Broadcast Management ......................................................................... 43

6.4.2.5 Results of LCN Test .............................................................................................. 44

6.4.3 Network Evolution .............................................................................................................. 45

6.4.3.1 Service Addition and Deletion ............................................................................... 46

6.4.3.2 Clash LCN Resolution ........................................................................................... 48

6.4.3.3 Multiplex Addition and Deletion ............................................................................. 51

6.4.3.4 Service and Event Updates ................................................................................... 53

6.4.3.5 Results of Network Evolution Test ........................................................................ 56

6.4.4 Character Test .................................................................................................................... 56

6.4.4.1 Event p/f ................................................................................................................ 57

6.4.4.2 Event Schedule ..................................................................................................... 60

6.4.4.3 Event p/f (Huffman Encoding) ............................................................................... 62

6.4.4.4 Event Schedule (Huffman Encoding) .................................................................... 65

6.4.4.5 Huffman Encoding (Malay) .................................................................................... 66

6.4.4.6 Huffman Encoding (ESC character) ...................................................................... 67

6.4.4.7 No Table Definition ................................................................................................ 68

6.4.4.8 Latin Table 05 - ISO-8859-9 .................................................................................. 69

6.4.4.9 Results of Character Test ...................................................................................... 70

6.4.5 Active Format Descriptor (AFD) Test ................................................................................. 70

6.4.5.1 AFD........................................................................................................................ 71

6.4.5.2 Results of AFD Test .............................................................................................. 73

6.4.6 Multiple Physical Layer....................................................................................................... 74

6.4.6.1 Multiple Physical Layer Pipes ................................................................................ 75

6.4.6.2 Results of Multiple-PLP Test ................................................................................. 77

6.4.7 Self Declaration .................................................................................................................. 77

6.4.7.1 Results of Declaration ........................................................................................... 77

6.4.7.2 Notes - T2Xpress Settings .................................................................................... 78

7. Malaysia (MYS) SI/PSI Test Requirement ........................................................................................ 79

7.1 Frequency Range ........................................................................................................................ 79

7.2 Service Installation ....................................................................................................................... 79

7.3 Video Decoding ........................................................................................................................... 80

7.4 Audio Decoding ........................................................................................................................... 80

7.5 Subtitling ...................................................................................................................................... 81

7.6 Time and Data Information .......................................................................................................... 81

7.7 EIT Presentation .......................................................................................................................... 81

7.8 Audio and Subtitle Language Support ......................................................................................... 82

7.9 Logical Channel Numbering ........................................................................................................ 82

7.10 Network Evolution ...................................................................................................................... 83 iii

MCMC MTSFB TC T011:2014

7.11 Time Exclusive Services ............................................................................................................ 84

8. Malaysia DVB-T2 Over Air Download (OAD) Test Suite Ver1.0....................................................... 85

8.1 Revision history ........................................................................................................................... 85

8.2 Evaluation details ......................................................................................................................... 85

8.3 Evaluation Results ....................................................................................................................... 85

8.4 Test Description ........................................................................................................................... 86

8.5 Results of OAD Test .................................................................................................................... 87

8.6 Test Environment ......................................................................................................................... 88

8.7 Transport Stream Structure ......................................................................................................... 89

8.7.1 Transport Stream (option 1) ............................................................................................... 89

8.7.2 Transport Stream (option 2) ............................................................................................... 90

9. Malaysia Hybrid Broadcast TV (HBBTV) Test Suite Ver1.0 ............................................................. 91

9.1 Revision history ........................................................................................................................... 91

9.2 Evaluation details ......................................................................................................................... 91

9.3 Evaluation results ........................................................................................................................ 91

9.4 Test Suite ..................................................................................................................................... 91

9.4.1 HbbTV 0.9 .......................................................................................................................... 91

9.4.1.1 Results ................................................................................................................. 100

9.4.2 Dynamic Adaptive Streaming over HTTP (DASH) ........................................................... 100

9.4.2.1 Results ................................................................................................................. 101

9.4.3 Recording ......................................................................................................................... 101

9.4.3.1 Results ................................................................................................................. 101

9.4.4 Marlin Digital Rights Management (DRM)........................................................................ 101

9.4.4.1 Results ................................................................................................................. 102

9.4.5 Event Information Table (EIT) ................................................................................................ 102

9.4.5.1 Results ................................................................................................................. 102

9.5 References ................................................................................................................................ 103

Acknowledgements ............................................................................................................................. 104 iv

MCMC MTSFB TC T011:2014

Committee Representation

The Multimedia Terminal Working Group (MMT WG) under the Malaysian Technical Standards Forum

Berhad (MTSFB) which supervised the development of this Technical Code consists of representatives from the following organizations:

Al Hijrah Media Corporation (TV Alhijrah)

Asian Broadcasting Networks (M) Sdn Bhd (ABNxcess)

Dolby Laboratories Inc.

Eastool Solution Sdn Bhd

Fraunhofer IIS

Guillemard Engineering Services

Hanitek Sdn Bhd

LG Electronics (M) Sdn Bhd

Malaysian Technical Standards Forum Berhad (MTSFB)

Media Prima Berhad

MyTV Broadcasting Sdn Bhd

Panasonic AVC Networks Kuala Lumpur Malaysia Sdn Bhd

Radio Television Malaysia (RTM)

Rohde & Schwarz Malaysia Sdn Bhd

Samsung Malaysia Electronics (SME) Sdn Bhd

Sharp (M) Sdn Bhd

SIRIM QAS International Sdn Bhd

Sony EMCS (M) Sdn Bhd

Toshiba (M) Sdn Bhd

The Testing Material Sub Working Group of the Multimedia Terminal Working Group (MMT WG) which developed this Technical Code consists of representatives from the following organizations:

Al Hijrah Media Corporation (TV Alhijrah)

Dolby Laboratories Inc.

Hanitek Sdn Bhd

LG Electronics (M) Sdn Bhd

Malaysian Technical Standards Forum Berhad (MTSFB)

Media Prima Berhad

MyTV Broadcasting Sdn Bhd

Panasonic AVC Networks Kuala Lumpur Malaysia Sdn Bhd

Radio Television Malaysia (RTM)

Rohde & Schwarz Malaysia Sdn Bhd

Samsung Malaysia Electronics (SME) Sdn Bhd

Sharp (M) Sdn Bhd

SIRIM QAS International Sdn Bhd

Sony EMCS (M) Sdn Bhd

Toshiba (M) Sdn Bhd v

MCMC MTSFB TC T011:2014

FOREWORD

This technical code for the Specifications on Common Test Suite for Digital Terrestrial Television

Broadcast Service Receiver (‘this Technical Code’) was developed by the Testing Material Sub

Working Group of the Multimedia Terminal Working Group under the Malaysian Technical Standards

Forum Berhad (MTSFB) in accordance with Section 185 of the Communications and Multimedia Act

1998.

This Technical Code was developed to specify the common test suite for digital terrestrial television broadcast service receivers for the purpose of certifying the devices under the Communications and

Multimedia (Technical Standards) Regulations 2000.

This Technical Code shall continue to be valid and effective until reviewed or cancelled. vi

MCMC MTSFB TC T011:2014

SPECIFICATIONS ON COMMON TEST SUITE FOR DIGITAL TERRESTRIAL

TELEVISION BROADCAST SERVICE RECEIVER

1. Scope

This Technical Code describes the test methods for the digital terrestrial television broadcast receivers in complying with the SKMM MTSFB TC T004: 2013 - Specification for Digital Terrestrial

Television Broadcast Service Receivers, SKMM MTSFB TC G001: 2013 - Compression Table of

Service Information (SI) Descriptions for Digital Terrestrial Television Broadcast Service and SKMM

MTSFB TC G002: 2013 - Middleware Profile for Digital Terrestrial Television Broadcast Service. The receivers may include Integrated Digital Televisions (IDTVs), Set Top Boxes (STBs) and other types of stand-alone receivers for the reception of digital terrestrial television broadcast service in Malaysia.

2. Normative References

The following normative references are indispensable for the application of this Technical Code. For dated references, only the edition cited applies. For undated references, the latest edition of the normative reference (including any amendments) applies.

SKMM MTSFB TC T004: 2013, Specification for Digital Terrestrial Television Broadcast Service

Receiver

SKMM MTSFB TC G001: 2013, Compression Table of Service Information (SI) Descriptions for

Digital Terrestrial Television Broadcast Service

SKMM MTSFB TC G002: 2013, Middleware Profile for Digital Terrestrial Television Broadcast Service

Television Digital Terrestre Hibrida

Test Suite for HbbTV Specification Version 2, 1 October 2014

TNT 2.0 Terminal Specification V1.1, July 2012

3. Abbreviations

For the purposes of this Technical Code, the following abbreviation applies.

AAC Advanced Audio Coding

AFC

AFD

Automatic Frequency Control

Active Format Descriptor

AIT

API

AVC

C/N

CSS

DASH

DRM

DSM-CC

EIT

Application Information Table

Application Protocol Interface

Advanced Video Coding

Carrier to Noise Ratio

Cascading Style Sheets

Dynamic Adaptive Streaming over HTTP

Digital Rights Management

Digital Storage Media Command and Control

Event Information Table

1

MCMC MTSFB TC T011:2014

PAPR

PLP

PSI

QAM

QEF

RF

RUT

MISO

MPD

MPEG

MPLP

OAD

OFDM

OIPF

OUI

EIT [p/f]

EPG

FEC

FFT

GI

HbbTV

HE-AAC

HTML

HTTP

IDTV iDTV

IRD

ISSY

LCN

SFN

SI

SISO

SSU

STB

TS

UTF

UHF

URL

VHF

VSB

XML

Information on the current event (p:present) and next event (f:following) in the EIT

Electronic Program Guide

Forward Error Correction

Fast Fourier Transforms

Guard Intervals

Hybrid Broadcast Broadband Television

High Efficiency Advanced Audio Coding

HyperText Markup Language

HyperText Transfer Protocol

Integrated Digital Television

Integrated Digital Television (receiver)

Integrate Receiver Decoder

Input Stream SYnchronizer

Logical Channel Number

Multiple Input Single Output

Minimum Product Distance

Moving Picture Experts Group

Multiple Physical Layer Pipe

Over Air Download

Orthogonal Frequency Division Multiplexing

Open IPTV Forum

Organizationally Unique Identifier

Peak to Average Power Ratio

Physical Layer Pipes

Program Service Information

Quadrature Amplitude Modulation

Quasi Error Free

Radio Frequency

Receiver Under Test

Single Frequency Network

Service Information

Single Input Single Output

System Software Update

Set Top Box

Transport Stream

Universal Transformation Format

Ultra High Frequency

Uniform Resource Locator

Very High Frequency

Vestigial Sideband eXtensible Markup Language

2

MCMC MTSFB TC T011:2014

4. Requirements

4.1 RF

The receiver shall comply and pass the RF tests as specified in the Malaysia DVB-T2 RF

Performance Test Suite Ver1.0

4.2 SI/PSI

The receiver shall comply and pass the tests as specified in Malaysia DVB-T2 SI/PSI Conformance

Test Suite Ver1.0

4.3 OAD

The receiver shall comply and pass the OAD tests as specified in the Malaysia DVB-T2 Over Air

Download (OAD) Test Suite Ver1.0

4.4 HbbTV

The receiver shall comply and pass the HBBTV tests as specified in the Malaysia Hybrid Broadcast

TV (HbbTV) Test Suite Ver1.0

3

MCMC MTSFB TC T011:2014

5. Malaysia DVB-T2 RF Performance Test Suite Ver1.0

5.1 Revision History

No Date Description Version

First official release v1.0 1 2014-06-03

5.2 Evaluation Details

Receiver Under Test (RUT)

RUT Device Type (iDTV/ Set top box)

RUT Firmware Version

5.3 Evaluation Results

Section

1.0

Test Category

C/N Performance on Gaussian channel (dB)

2.0

3.0

C/N Performance on 0dB echo channel (dB)

Minimum receiver signal input levels on

Gaussian channel (dBm)

4.0

5.0

6.0

7.0

8.0

9.0

10.0

11.0

12.0

13.0

Minimum IRD Signal Input Levels on 0dB echo channel

Maximum receiver signal input levels (dBm)

Immunity to "digital" signals in Other Channels

Immunity to Co-Channel Interference from

Analogue TV Signals

Immunity to Adjacent Channel Interference

From Analogue TV Signals

Performance in Time-Varying Channels 10Hz

Doppler (5Hz after AFC) 20μs 0dB echo

Synchronisation for varying echo power levels in SFN (dB)

C/(N+I) Performance in Single Frequency

Networks for more than one echo (dB)

C/(N+I) Performance in Single Frequency

Networks inside the guard interval (dB)

C/(N+I) Performance in Single Frequency

Networks outside the guard interval (dB)

OVERALL RESULT

Result

Remark

Remarks

4

MCMC MTSFB TC T011:2014

5.4 Malaysia DVB-T2 RF Modes and Performance Figure

5.4.1 RF Profile for Malaysia

Identifier MS 1 MS 2

Overall

FFT Size 32K 32K

GI

SISO/MISO

PAPR

Bandwidth

1/8

SISO

TR

8MHz

19/256

SISO

TR

8MHz

Carrier Mode

Pilot Pattern

L1 Modulation

Data Symbols per Frame (Ldata)

OFDM Symbols per Frame (Lf)

Frame Duration (ms)

Frames Per SuperFrame

PLP #0

Extended

PP2

64 QAM

43

44

178

2

Extended

PP4

64 QAM

61

62

239

2

PLP Type

Time Interleaver Type (TIME_IL_Type)

Modulation

Rate

FEC Type

Rotated QAM

FEC blocks per interleaving Frame

Full channel (Trial mode)

TI blocks per frame (N_TI)

Frame_Interval (I_JUMP)

TIME_IL_LENGTH

Approx. Time Interleaving Length (ms)

Data Rate (Mbit/s)

1

0

256 QAM

3/4

64 LDPC

Yes

135

2

1

2

89

36.9256

1

0

256 QAM

3/5

64 LDPC

Yes

200

3

1

3

81

32.49116

MS 3

32K

1/128

SISO

TR

8MHz

Extended

PP7

64 QAM

59

60

217

2

1

0

256 QAM

2/3

64 LDPC

Yes

200

3

1

3

72

39.8165

PP2

64 QAM

43

44

203

2

1

MS 4

32K

1/8

SISO

TR

7MHz

Normal

0

256 QAM

3/4

64 LDPC

Yes

132

2

1

2

101

31.5919

5

MCMC MTSFB TC T011:2014

5.4.2 Performance Figures for Malaysia

Test

Section

Section

Identifier

Description

1.0 A.1

C/N Performance on Gaussian channel (dB)

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

10.0

11.0

12.0

A.2

A.3

A.4

A.5

A.6

A.7

A.8

A.9

A.10

A.11

A.12

A.13

MS 1

22.9

MS 2 MS 3

Performance Figure

18.9 19.7

C/N Performance on 0dB echo channel (dB)

Minimum receiver signal input levels on Gaussian channel

(dBm)

Minimum IRD Signal Input

Levels on 0dB echo channel

28.0

-76.2

-71.1

22.6

-80.2

-76.5

23.9

-79.3

-75.1

Receiver noise figure on

Gaussian channel

1

Maximum receiver signal input levels (dBm)

6.0

-35

Immunity to "digital" signals in Other Channels

Digital ACI N+/-1 C/I (dB) -28.0

Digital ACI N+/-2 C/I (dB)

Digital ACI N+9 C/I (dB)

-38.0

-28.0

6.0

-35

-28.0

-38.0

-28.0

6.0

-35

-28.0

-38.0

-28.0

Immunity to Co-Channel Interference from Analogue TV Signals

PAL B/G CCI C/I (dB) 7.0 3.0 5.0

Immunity to Adjacent Channel Interference From Analogue TV Signals

-33.0

-44.0

-44.0

-33.0

-44.0

-44.0

-33.0

-44.0

-44.0

PAL B/G ACI C/I N+/-1 (dB)

PAL B/G ACI C/I N+/-2 (dB)

PAL B/G ACI C/I N+9 (dB)

Performance in Time-Varying

Channels 10Hz Doppler (5Hz after AFC) 20 μs 0dB echo

Synchronisation for varying echo power levels in SFN (dB)

C/(N+I) Performance in Single

Frequency Networks for more than one echo (dB)

C/(N+I) Performance in Single

Frequency Networks inside the guard interval (dB)

3

31.0

28.0

28.0

3

26.1

22.6

22.6

3

28.1

23.9

23.9

MS 4

22.9

28.0

-76.9

-71.8

6.0

-35

-28.0

-38.0

-28.0

7.0

-33.0

-44.0

-44.0

3

31.0

28.0

28.0

1

No testing is required as this is purely calculation based

6

MCMC MTSFB TC T011:2014

Test

Section

Section

Identifier

Description

MS 1 MS 2 MS 3

Performance Figure

MS 4

13.0 A.14

C/(N+I)

Performance in Single

Frequency

Networks outside the guard interval (dB)

Echo

Delay

(μs)

Echo level

(dBc)

-532 -12.0

Echo

Delay

(μs)

-525 -11.5

-510 -10.5

-490 -9.0

-475 -7.5

Echo level

(dBc)

See Note 1

-448 -2.0 -266

448 -2.0 266

475 -7.5

490 -9.0

510 -10.5

525 -11.5

-2

-2

See Note 1

Echo

Delay

(μs)

Echo level

(dBc)

Echo

Delay

(μs)

Echo level

(dBc)

-133 -9.5 -608 -12.0

-120 -9.0 -600 -11.5

-90 -7.5 -580 -10.5

-60

-30

-28

28

-5.0

-2.0

-2.0

-2.0

-560

-540

-512

512

-9.0

-7.0

-2.0

-2.0

30

60

-2.0 540 -7.0

-5.0 560 -9.0

90 -7.5 580 -10.5

120 -9.0 600 -11.5

532 -12.0 133 -9.5 608 -12.0

Note 1: There is no allowance for echo outside guard for 19/256 PP4 in Nordig due to 19/256 guard

(266

 s) being very close to the Nyquist limit for PP4 (298.67

 s). Nordig defines the max delay for echo outside guard to be 57/64*Nyquist which is equal to the guard interval of

266

 sec for 19/256 PP4.

7

MCMC MTSFB TC T011:2014

5.5 Test Instrument Set Up

Figure A

Figure B

Test Instrument Set Up

8

Applicable

Section

1.0

2.0

3.0

4.0

5.0

9.0

10.0

6.0

Figure C

Figure D

Test Instrument Set Up

MCMC MTSFB TC T011:2014

Applicable

Section

7.0

8.0

11.0

12.0

13.0

9

MCMC MTSFB TC T011:2014

5.6 Test Category

5.6.1 Carrier to Noise Ratio (C/N) Performance on Gaussian Channel

Section: 1.0

Test Case:

Requirement:

C/N Performance on Gaussian channel.

Receiver shall have at least the quasi error free (QEF) performance for the C/N ratios given in the Performance Figure outlined in Annex A of the SKMM MTSFB

TC T004:2013 - Specification for Digital Terrestrial Television Broadcast Service

Receiver.

Purpose:

Expectation:

To test the required C/N for QEF reception in Gaussian channel.

The required C/N for QEF reception in Gaussian channel shall be lesser than the figures specified in Annex A of the SKMM MTSFB TC T004:2013 -

Specification for Digital Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up:

Figure A

Calibration

Requirement:

1

Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Ensure that the receiver signal input level (wanted signal) is set to -50dBm.

Test Outline:

3 Perform a channel search (tune) on frequency 666MHz.

1 Adjust and measure the C/N for the range of frequencies and T2 modes defined below for QEF reception.

2 Remark

Result:

Conformity:

The performance requirement is based on 30 seconds error free video.

C/N

Centre Frequency

(MHz)

MS 1

474.0 570.0 666.0 762.0 858.0

MS 2

MS 3

MS 4

X

X

X

X

X

X X

X

X

X

X

X

X

** Remark - If 'Failed', please indicate the level of failure (dB)

Passed Failed Not Tested

1

Remark: 2

3

Note: Attach graph (if any)

X Indicates no test needed

10

MCMC MTSFB TC T011:2014

5.6.2 C/N Performance on 0dB Echo Channel

Section: 2.0

Test Case:

Requirement:

Purpose:

Expectation:

C/N Performance on 0dB echo channel.

Receiver shall have at least the QEF performance for the C/N ratios given in the

Performance Figure outlined in Annex A of the SKMM MTSFB TC T004:2013 -

Specification for Digital Terrestrial Television Broadcast Service Receiver.

To test the required C/N for QEF reception in 0dB echo channel.

The required C/N for QEF reception in 0dB echo channel shall be lesser than the figures specified in Annex A of the SKMM MTSFB TC T004:2013 - Specification

for Digital Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up:

Figure A

Calibration

Requirement:

1

Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Ensure that the fading simulator is set at 0dB echo profile with a delay of

1.95µs, 0 degree phase offset from channel centre and 0dB attenuation on the second path.

Test Outline:

Result:

3 Ensure that the receiver signal input level (wanted signal) is set to -50dBm.

4 Perform a channel search (tune) on frequency 666MHz.

1 Adjust and measure the C/N for the range of T2 modes defined below for

QEF reception in 0dB echo channel.

2 Remark

The performance requirement is based on 30 seconds error free video.

Modes

MS 1

MS 2

MS 3

MS 4

C/N

X

** Remark - If 'Failed', please indicate the level of failure (dB)

Passed Failed Not Tested Conformity:

Remark:

1

2

3

Note: Attach graph (if any)

X Indicates no test needed

11

MCMC MTSFB TC T011:2014

5.6.3 Minimum Receiver Signal Input Levels on Gaussian Channel

Section 3.0

Test Case Minimum receiver signal input levels on Gaussian channel.

Requirement

Purpose

Expectation

The receiver shall provide QEF reception for the minimum signal levels (P min

) for

8MHz Extended bandwidth as given in the Performance Figure outlined in

Annex A of the SKMM MTSFB TC T004:2013 - Specification for Digital

Terrestrial Television Broadcast Service Receiver.

(P min

= -105.1 dBm + NF [dB] + C/N [dB])

To verify the sensitivity of the receiver on Gaussian channel over the supported frequency range.

The sensitivity shall be equal or better for all measured frequencies (channels) and for all modes specified in Annex A of the SKMM MTSFB TC T004:2013 -

Specification for Digital Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up

Figure A

Calibration

Requirement

1

Set up the equipment based on the modes outlined in Annex A of the

SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver. (Start with MS 1)

2 Obtain the receiver signal (wanted signal) input level by taking consideration of the attenuation from the attenuator and cables.

3 Perform a channel search (tune) on frequency 666MHz, with the wanted signal level set to -50dBm.

1

Increase the received signal input level from low to higher value until QEF reception is achieved. This will be the minimum receiver signal input level.

Test Outline

Result

2 Repeat the test for the range of frequencies and T2 modes defined below.

3 Remark

The performance requirement is based on 30 seconds error free video.

C/N

Centre Frequency (MHz) 474.0 570.0 666.0 762.0 858.0

MS 1

MS 2

MS 3

MS 4

X

X

X

X

X

X X

X

X

X

X

X

X

** Remark - If 'Failed', please indicate the level of failure (dB)

Conformity Passed

1

Remark 2

3

Note: Attach graph (if any)

X Indicates no test needed

Failed Not Tested

12

MCMC MTSFB TC T011:2014

5.6.4 Minimum Integrated Receiver Decoder (IRD) Signal Input Levels on 0db Echo Channel

Section 4.0

Test Case Minimum IRD signal input levels on 0dB echo channel.

Requirement

Purpose

The receiver shall provide QEF reception for the minimum signal levels (P min

) for

8MHz Extended bandwidth as given in the Performance Figure outlined in Annex

A of the SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver. (P min

= -105.1 dBm + NF [dB] + C/N [dB])

To verify the sensitivity of the receiver on frequency selective channel.

Expectation

The minimum signal level shall be equal or lower in dBm for all modes specified in Annex A of the SKMM MTSFB TC T004:2013 - Specification for Digital

Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up

Figure A

Calibration

Requirement

1 Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Ensure that the fading simulator is set at 0dB echo profile with a delay of

1.95µs, 0 degree phase offset from channel centre and 0dB attenuation on the second path.

3 Obtain the receiver signal (wanted signal) input level by taking consideration of the attenuation from the attenuator and cables.

4 Perform a channel search (tune) on frequency 666MHz with the wanted signal level set to -50dBm.

1 Increase the received signal input level from low to higher value until QEF reception is achieved. This will be the minimum receiver signal input level.

Test Outline

Result

2 Repeat the test for the range of T2 modes defined below.

3

Remark

1. The performance requirement is based on 30 seconds error free video.

2. 0dB echo profile must be activated when measuring the power level.

Minimum input signal levels

0db echo (μs) 10 26 133 224 253 426

MS 1

MS 2

MS 3

MS 4 X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

** Remark - If 'Failed', please indicate the level of failed (dB)

Passed Failed Not Tested Conformity

1

Remark 2

3

Note: Attach graph (if any)

X Indicates no test needed

13

MCMC MTSFB TC T011:2014

5.6.5 Maximum Receiver Signal Input Levels

Section 5.0

Test Case

Requirement

Purpose

Maximum receiver signal input levels.

The receiver shall provide QEF reception for DVB-T and DVB-T2 signals up to the level specified in Annex A of SKMM MTSFB TC T004:2013 - Specification for

Digital Terrestrial Television Broadcast Service Receiver.

To test that the receiver is able to handle high power RF signals.

Expectation

The reception shall be QEF for input level higher than or equal to the level for all modes specified in Annex A of SKMM MTSFB TC T004:2013 - Specification for

Digital Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up

Figure A

1

Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

Calibration

Requirement 2 Obtain the receiver signal (wanted signal) input level by taking consideration of the attenuation from the attenuator and cables.

3 Perform a channel search (tune) on frequency 666MHz.

Test Outline

1 Increase the received signal input level until QEF reception is achieved. Ensure that the receiver is able to output the content of the TS source as the receiver signal level increases.

2 Repeat the test for the range of T2 modes defined below.

3 Remark

Result

The performance requirement is based on 30 seconds error free video with the receiver input signal level calculated as a function of attenuation.

Modes

MS 1

MS 2

MS 3

MS 4

Maximum input signal levels

X

** Remark - If 'Failed', please indicate the level of failure (dBm)

Conformity Passed

Remark

1

2

3

N ote: Attach graph (if any)

X Indicates no test needed

Failed Not Tested

14

MCMC MTSFB TC T011:2014

5.6.6 Immunity to "Digital" Signals in Other Channels

Section 6.0

Test Case

Requirement

Immunity to "digital" signals in Other Channels.

The receiver shall permit an interfering DVB-T or DVB-T2 signal for the supported frequencies outlined in Annex A of the SKMM MTSFB TC T004:2013 -

Specification for Digital Terrestrial Television Broadcast Service Receiver with a minimum interference to signal level ratio (I/C) while maintaining QEF reception.

Purpose

Expectation

To verify the QEF reception for digital signal interference on adjacent or other channels.

The wanted DVB-T2 signal shall be QEF for the interference signal levels specified for all modes outlined in Annex A of the SKMM MTSFB TC T004:2013 -

Specification for Digital Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up

Figure B

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Perform a channel search (tune) on frequency 666MHz, with the interferer switched off.

3 With Channel B or the interferer signal level set to -20dBm, decrease the receiver signal input level (Channel A or the wanted signal) until QEF is obtained.

4 Remark

1. Require the interferer to operate at DVB-T2 extended mode for worst case testing.

2. Ensure that the interferer signal does not have too high shoulders to avoid out-of-band emissions in the reception of the wanted signal. Use a band pass filter on the interference signal if necessary.

1 Select the frequencies for Channel A and Channel B based on the required values indicated in the Result Table.

2 The difference in signal level shall be measured at QEF reception.

3 Remark

The performance requirement is based on 30 seconds error free video.

15

MCMC MTSFB TC T011:2014

Result

Centre Frequency (MHz) -

666MHz

Interferer Centre Frequency

(MHz)

MS 1

MS 2

MS 3

MS 4

Centre Frequency (MHz) -

786MHz

Interferer Centre Frequency

(MHz)

MS 1

MS 2

MS 3

MS 4

650

X

770

X

658

X

778

X

C/I

674

X

C/I

794

X

** Remark - If 'Failed', please indicate the level of failure (dB)

682

X

802

X

Conformity

1

Passed

Remark 2

3

Note: Attach graph (if any)

X Indicates no test needed

Failed Not Tested

738

X

858

X

16

MCMC MTSFB TC T011:2014

5.6.7 Immunity to Co-Channel Interference from Analogue TV Signals

Section 7.0

Test Case

Requirement

Immunity to Co-Channel Interference from Analogue TV Signals.

The receiver shall perform better than the RF figure specified in Annex A of the

SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver when the signal is exposed to interference from a co-channel G/PAL signal including video with teletext, FM audio and a NICAM sub carrier while maintaining QEF reception.

Purpose

Expectation

To verify the QEF reception for DVB-T2 receiver when there is a co-channel interference from analogue TV.

The received signal shall have a 30s error free video for DVB-T2 modes with C/I equal or better than the requirement.

Test Instrument

Set Up

Figure C

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the

SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver. (Start with MS 1)

2 Ensure the following:

1. 10% modulation depth for vision carrier.

2. NICAM signal level is at -20dB and +5.85MHz relative to the vision carrier.

3. Insert 12 lines of teletext.

3 Set the analogue TV source with the following requirements:

1. The analogue TV source and DVB-T2 modulator shall be connected to the same reference signal (10MHz).

2. The analogue TV source shall have 0Hz centre frequency offset from the digital TV source.

3. The analogue TV source should not have too high out-of-band emissions to avoid interference to other frequencies.

4. Use a colour bar 75% as the input for PAL signal.

5. FM sound carrier can be modulated at a deviation of 1kHz - 50kHz tone, and the level set at -13dB relative to the vision carrier.

4 Calibrate the C/I level (Att C and Att I).

5 Ensure that the receiver signal input level (wanted signal) is set to -50dBm.

1 Execute the test for the range of the frequencies and modes outlined in the

Result Table.

2 Increase the C/I from low value to higher value until the QEF measurement is achieved.

3 Remark

The performance requirement is based on 30 seconds error free video.

17

MCMC MTSFB TC T011:2014

Result

Centre Frequency (MHz)

MS 1

MS 2

MS 3

MS 4

C/I

666

X

** Remark - If 'Failed', please indicate the level of failure (dB)

Passed Failed Not Tested Conformity

Remark

1

2

3

Note: Attach graph (if any)

X Indicates no test needed

18

MCMC MTSFB TC T011:2014

5.6.8 Immunity to Adjacent Channel Interference from Analogue TV Signals

Section 8.0

Test Case

Requirement

Immunity to Adjacent Channel Interference From Analogue TV Signals.

The receiver shall perform better than the RF figure specified in Annex A of the

SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver when the signal is exposed to interference from adjacent G/PAL signal including video with teletext, FM audio and a NICAM sub carrier while maintaining QEF reception.

Purpose

Expectation

To verify the QEF reception for DVB-T2 receiver when there is adjacent channel interference from analogue TV.

The received signal shall have a 30s error free video for DVB-T2 modes with C/I equal or better than the requirement.

Test Instrument

Set Up

Figure C

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Ensure the following:

1. 10% modulation depth for vision carrier.

2. NICAM signal level is at -20dB and +5.85MHz relative to the vision carrier.

3. Insert 12 lines of teletext.

3 Set the analogue TV source with the following requirements:

1. The analogue TV source and DVB-T2 modulator shall be connected to the same reference signal (10MHz).

2. The analogue TV source shall have a centre frequency value from the digital TV source (indicated in the Result Table below).

3. The analogue TV source should not have too high out-of-band emissions to avoid interference to other frequencies.

4. Use a colour bar 75% as the input for PAL signal.

5. FM sound carrier can be modulated at a deviation of 1kHz - 50kHz tone, and the level set at -13dB relative to the vision carrier.

4 Calibrate the C/I level (Att C and Att I).

5 Ensure that the receiver input level for analogue TV (unwanted signal) is set to -25dBm (defined as the R.M.S value of the vision carrier at peaks of the modulated envelope).

1 Execute the test for the range of the frequencies and modes outlined in the

Result Table.

2 Increase the C/I from high value to lower value until the QEF measurement is achieved. This should be achieved by keeping the level of the unwanted signal and decreasing the level of the wanted signal.

3 Remark

The performance requirement is based on 30 seconds error free video.

19

MCMC MTSFB TC T011:2014

Result

Conformity

Centre Frequency (MHz) - 666MHz C/I

Interferer Centre Frequency (MHz) 650 658 674 682 738

MS 1

MS 2

MS 3

MS 4

Centre Frequency (MHz) - 786MHz

X X X

C/I

X X

Interferer Centre Frequency (MHz) 770 778 794 802 858

MS 1

MS 2

MS 3

MS 4 X X X X X

** Remark - If 'Failed', please indicate the level of failure (dB)

Passed Failed Not Tested

1

Remark 2

3

Note: Attach graph (if any)

X Indicates no test needed

20

MCMC MTSFB TC T011:2014

5.6.9 Performance in Time-Varying Channels 10Hz Doppler (5Hz after Automatic Frequency

Control (AFC)) 20μs 0dB Echo

Section 9.0

Test Case

Performance in Time-Varying Channels 10Hz Doppler (5Hz after AFC) 20μs 0dB echo.

Requirement

Purpose

Expectation

The receiver shall be able to operate with all signal time variations. The increase in required C/N for QEF reception shall be less than the RF figures specified in

Annex A of the SKMM MTSFB TC T004:2013 - Specification for Digital

Terrestrial Television Broadcast Service Receiver, corresponding to a Doppler shift of +/- 10Hz (5Hz after AFC) compared to a 0dB echo with a delay of 20μs.

To verify the QEF reception for DVB-T2 receiver on a channel where time variation exists.

The increase in the required C/N shall be less than the RF figures specified in

Annex A of the SKMM MTSFB TC T004:2013 - Specification for Digital

Terrestrial Television Broadcast Service Receiver for 0dB 20μs echo from frequency separation 1Hz to 10Hz.

Test Instrument

Set Up

Figure A

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Ensure that the fading simulator is set at 0dB echo profile with a delay of

20µs, 0 degree phase offset from channel centre and 0dB attenuation on the second path (for 1Hz frequency separation).

3 Configure the following:

1. Path 1: Static, 0dB attenuation, and 0μs delay.

2. Path 2: Pure Doppler, 0dB attenuation, and 20μs delay.

4 Ensure that the receiver signal input level (wanted signal) is set to -50dBm

(with no noise applied).

5 Perform a channel search (tune) on frequency 666MHz.

1 Execute the test for the range of the frequencies and modes outlined in the

Result Table.

2 Increase the C/I from low value to higher value until the QEF measurement is achieved.

3 Remark

The performance requirement is based on 30 seconds error free video.

21

MCMC MTSFB TC T011:2014

Result

Centre Frequency

(MHz) 666MHz

Frequency Separation

(Hz)

MS 1

MS 2

MS 3

MS 4

1

X

5

X

10

X

C/N

Max difference dB

X

** Remark - If 'Failed', please indicate the level of failure (dB)

Failed Not Tested Conformity

1

Passed

Remark 2

3

Note: Attach graph (if any)

X Indicates no test needed

Pass/

Fail

X

22

MCMC MTSFB TC T011:2014

5.6.10 Synchronization for Varying Echo Power Levels in Single Frequency Networks (SFN)

Section 10.0

Test Case

Requirement

Purpose

Synchronization for varying echo power levels in SFN.

The required C/N value for QEF reception as specified in Annex A of the

SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver shall be obtained when the channel contains two paths with relative delay from 1.95μs up to 0.95 x GI length and the relative power levels of the two paths are dynamically varying including 0dB echo level crossing.

To verify the SFN synchronization when the amplitude of the echo compared to the amplitude of the direct signal varies in a function of time.

Expectation

The receiver shall maintain SFN synchronization and the C/N value shall not exceed the specified value outlined in Annex A of the SKMM MTSFB TC

T004:2013 - Specification for Digital Terrestrial Television Broadcast Service

Receiver when the amplitude of the echo signal varies in time.

Test Instrument Set

Up

Figure A

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the

SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver. (Start with MS 1)

2 Set up the fading simulator as follows, disconnecting and re-connecting the wanted signal after the echo delay is changed between each test.

1. Path 1 (direct): 0dB attenuation, 0μs delay.

2. Path 2 (1st echo): 0dB attenuation and delay value from the Result

Table.

3. Path 3 (2nd echo): 1dB attenuation and delay value from the Result

Table with 0.1Hz frequency separation.

3 Ensure that the receiver signal input level (wanted signal) is set to -

50dBm (with no noise applied).

4 Perform a channel search (tune) on frequency 666MHz.

1 Increase the C/N from low to higher value until QI reception is achieved.

2 Repeat the test for the range of echo delay values and T2 modes defined in the Result Table below.

3 Remark

1. The performance requirement is based on 30 seconds error free video.

2. The QI reception shall be obtained when the channel contains two paths with relative delay from 1.95µs up to 0.95 x GI length and the relative power levels of the two paths are dynamically varying

(inclusive of 0dB echo level crossing).

3. FRY input signal to the receiver shall be disconnected when changing the echo delay.

23

MCMC MTSFB TC T011:2014

Result

0db echo (is)

MS 1

MS 2

MS 3

MS 4

10

X

26

X

X

X

133

C/N

224

X

X

X

X

X

X

** Remark - If 'Failed', please indicate the level of failure (dB)

253

X

X

X

Failed Not Tested Conformity

1

Passed

Remark 2

3

Note: Attach graph (if any)

X Indicates no test needed

426

X

X

X

24

MCMC MTSFB TC T011:2014

5.6.11 C/(N+I) Performance in SFN for more than one echo

Section 11.0

Test Case

Requirement

Purpose

C/(N+I) Performance in SFN for more than one echo.

The required C/N value for QI reception as specified in Annex A of SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television Broadcast

Service Receiver shall be obtained when the channel contains two static paths with relative delay from 1.95μs up to 0.95 x GI length, independently of the relative amplitudes and phases of the two paths.

To verify the SFN synchronization of the receiver when two echo signals are present.

Expectation

The receiver shall synchronize all combinations defined in the result table, with the C/N values not exceeding the required C/N figured defined outlined in Annex

A of the SKMM MTSFB TC T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver.

Test Instrument

Set Up

Figure D

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Set up the fading simulator as follows, disconnecting and re-connecting the wanted signal after the echo delay is changed between each test

1. Path 1 (static): 0dB attenuation, 0μs delay and 0 degree phase.

2. Path 2 (Pre echo): Follow the values specified in the table below (with 0 degree phase).

3. Path 3 (Post echo): Follow the values specified in the table below (with 0 degree phase).

3 Ensure that the receiver signal input level (wanted signal) is set to -50dBm

(with no noise applied).

4 Perform a channel search (tune) on frequency 666MHz.

1 Increase the C/N from low to higher value until QI reception is achieved.

2 Repeat the test for the range of echo delay values and T2 modes defined in the Result Table below.

3 Remark

1. The performance requirement is based on 30 seconds error free video.

2. FRY input signal to the receiver shall be disconnected when changing the echo delay.

25

MCMC MTSFB TC T011:2014

Result

Modes MS 1 MS 2 MS 3

Relative Delay

Difference

Path 2 Pre echo

0

3

6

9

12

15

18

21

15

15

15

15

15

6

9

12

18

21

15

15

0

3

Path 2 Pre echo

Path 3 Post echo

Path 3 Post echo

200.1μs -120.1μs

C/N

13.1μs

+200.0μs +120.0μs +13.0μs

0

3

15

18

21

0

3

6

9

2

6

9

12

18

21

15

15

15

15

15

15

15

** Remark - If 'Failed', please indicate the level of failure (dB)

Conformity

1

Passed

Remark 2

3

Note: Attach graph (if any)

X Indicates no test needed

Failed Not Tested

MS 4

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

26

MCMC MTSFB TC T011:2014

5.6.12 C/(N+I) Performance in Single Frequency Networks inside the Guard Interval (GI)

Section 12.0

Test Case

Requirement

Purpose

C/(N+I) Performance in SFN inside the guard interval.

The required C/N value for QI reception as specified in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television Broadcast

Service Receiver shall be obtained when the channel contains two static paths with relative delay from 1.95μs up to 0.95 x GI length, independently of the relative amplitudes and phases of the two paths.

To verify the required C/N for echoes in SFN inside the guard interval.

Expectation

The receiver shall synchronize in all echo attenuation and delay combinations defined in the result table, with the C/N values for 0dB echo not exceeding the required C/N figures outlined in Annex A of the SKMM MTSFB TC T004:2013 -

Specification for Digital Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up

Figure D

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Ensure that the fading simulator is set at 0dB echo profile with a delay of

1.95µs, 0 degree phase offset from channel centre and 0dB attenuation on the second path.

3 Ensure that the receiver signal input level (wanted signal) is set to -50dBm.

4 Perform a channel search (tune) on frequency 666MHz.

1 Apply noise and increase the C/N from low to higher value until QI reception is achieved.

2 Repeat the test for the range of echo values and T2 modes defined in the

Result Table below.

3 Remark

1. The performance requirement is based on 30 seconds error free video.

2. FRY input signal to the receiver shall be disconnected when changing the echo delay and attenuation level.

3. The delay of the echo shall be maintained constant during the changes of attenuation.

27

MCMC MTSFB TC T011:2014

Result

Delay(µs) -426 -224 -1.95 1.95 224 426

Attenuation (dB) 0 20 0 20 0 20 0 20 0 20 0 20

Mode

MS 1

Delay(µs)

X

-253

X

-133

X

-1.95 1.95 133 253

Attenuation (dB) 0 20 0 20 0 20 0 20 0 20 0 20

Mode

MS 2

X X X

Delay(µs) -26 -10 -1.95 1.95 10 26

Attenuation (dB) 0 20 0 20 0 20 0 20 0 20 0 20

Mode MS 3 X X X

** Remark - If 'Failed', please indicate the level of failure (dB)

Failed Not Tested Conformity

1

Passed

Remark 2

3

Note: Attach graph (if any)

X Indicates no test is needed

28

MCMC MTSFB TC T011:2014

5.6.13 C/(N+I) Performance in SFN outside the Guard Interval

Section 13.0

Test Case

Requirement

Purpose

C/(N+I) Performance in SFN outside the guard interval.

For echoes outside the guard interval, QI reception shall be possible with echo levels up to the values outlined in Annex A of the SKMM MTSFB TC T004:2013

- Specification for Digital Terrestrial Television Broadcast Service Receiver.

To verify the SFN synchronization in SFN for echoes outside guard interval.

Expectation

The echo levels shall be equal or higher compared to the FRY figures outlined in

Annex A of the SKMM MTSFB TC T004:2013 - Specification for Digital

Terrestrial Television Broadcast Service Receiver.

Test Instrument

Set Up

Figure D

Calibration

Requirement

Test Outline

1 Set up the equipment based on the modes outlined in Annex A of the SKMM

MTSFB TC T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver. (Start with MS 1)

2 Configure the echo signal with channel simulator relative delay difference set at 448µs.

3 Set the echo level to 0 dB.

4 Ensure that the receiver signal input level (wanted signal) is set to -50dBm.

5 Perform a channel search (tune) on frequency 666MHz.

1 Decrease the echo level from high to lower value until QEF reception is achieved.

2 Repeat the test for the range of echo values and T2 modes defined in the

Result Table below.

3 Remark

1. The performance requirement is based on 30 seconds error free video.

29

MCMC MTSFB TC T011:2014

Result

MS 1

Echo

Delay

(μs)

Echo level

(dBc)

Echo

Delay

(μs)

MS 2

Echo level

(dBc)

MS 3

Echo

Delay

(μs)

Echo level

(dBc)

-532 X X -133

-525 X X -120

-510 X X -90

-490 X X -60

-475 X X -30

-448 -266 -28

448 266 28

475 X X 30

490 X X 60

510 X X 90

525 X X 120

532 X X 133

** Remark - If 'Failed', please indicate the level of failure (dB)

Conformity Passed

Remark

1

2

3

Note: Attach graph (if any)

X Indicates no test is needed

Failed Not Tested

-540

-512

512

540

560

580

600

608

MS 4

Echo

Delay

(μs)

Echo level

(dBc)

-608

-600

-580

-60

X

X

X

X

X

X

X

X

X

X

X

X

30

MCMC MTSFB TC T011:2014

6. Malaysia DVB-T2 SI/PSI Conformance Test Suite Ver1.0

6.1 Revision History

No Date Description Version v1.0 1 2014-06-03

6.2 Evaluation Details

Receiver Under Test (RUT)

RUT Device Type (iDTV/Set top box)

First official release

RUT Firmware Version

6.3 Evaluation Results

Test Category

1.0 Basic SI/PSI

2.0 Logical Channel Numbering

3.0 Network Evolution

4.0 Character Test

5.0 Active Format Description

6.0 Multiple Physical Layer Pipes

(MPLP)

7.0 Declaration

Results Total

Test Approved by

Total Test

Item

Stamp

Pass Fail Not Tested

Signature

Remark

31

MCMC MTSFB TC T011:2014

6.4 Test Category

6.4.1 Basic SI/PSI Test

Description

This test contains the following sections:

Section 1.1 : Service Installation & Information

Section 1.2 : Event Information

Section 1.3 : Codec Information

Section 1.4 : Audio & Subtitle Language

Note :

Reference Document (Ref.): SKMM MTSFB TC

T004:2013 - Specification for Digital Terrestrial Television

Broadcast Service Receiver.

6.4.1.1 Service Installation and Information

Section 1.1 : Service Installation and Information

Test Streams :

MYS_SIPSI_1a.ts

Note :

The Test Streams are available with the

Communication and Multimedia Certification

Section, SIRIM QAS International Sdn Bhd

Stream Configuration :

Modulation Type : DVB-T2

Channel Frequency : 474 MHz - 858 MHz

Bandwidth : 8 MHz

Mode : 32K

Guard Interval : 1/128

Modulation : 256 QAM

Cell Identifier : 0

No. Test Instruction

1.1.1 Play out MYS_SIPSI_1a.ts and perform receiver full scan.

Enter each service and ensure that all of them are accessible via numerical keys.

Confirm the correct service name and

LCN numbering in each service.

Expectation

Observe the service name and LCN numbering for each service in the service list and ensure they are correctly arranged in an ascending order as below:

LCN 208 : TV1_SD

LCN 209 : TV2_HD

LCN 210 : TV3_HD

LCN 211 : TV4_SD

LCN 212: TV5_Radio

LCN 213: TV6_Radio

Ref.

3.2.11.1

Result Remarks

32

MCMC MTSFB TC T011:2014

Section 1.1 : Service Installation and Information

No. Test Instruction

1.1.2 Check clock information.

Expectation

Thursday 12 th

April 21:00:00.

6.4.1.2 Event Information

Section 1.2 : Event Information

No. Test Instruction

1.2.1 Play out MYS_SIPSI_1a.ts and

1.2.2

1.2.3 perform receiver full scan.

Using numerical keys, press '208' to enter service LCN 208 TV1_SD.

1.2.4

Access the banner and check the present (now) event information.

1.2.5

Note:

The event description may optionally be truncated by receiver when the character length exceeds the allocated

area for display of event description.

1.2.6

1.2.7 Next, access the banner again and

1.2.8

1.2.9

1.2.10 check the following (next) event information.

Note:

The event description may optionally be truncated by receiver when the

Service Name

Event start and end time

Event name

Short Event

Description

Extended

Event

Description

Rating

Event name

Short Event

Description

Expectation

TV1_SD

Thursday 12 th

April

21:00:00 - 21:30:00 (30 minutes).

TV1_SD Present Event

Short Event Description for TV1_SD

Present Event.

Extended Event Description for TV1_SD

Present Event: TV1_SD has a parental rating of 9 years and its genre is classified as Movie/Drama or Adult

Movie/Drama.

9 years

Service Name TV1_SD

Event start and end time

Thursday 12 th

April

21:30:00 - 22:00:00 (30 minutes).

TV1_SD Following Event

Short Event Description for TV1_SD

Following Event.

Ref.

3.2.13

Ref.

3.2.12

3.2.12.1

Result

Result

Remarks

Remarks

33

MCMC MTSFB TC T011:2014

Section 1.2 : Event Information

No.

1.2.11

Test Instruction character length exceeds the allocated

area for display of event description.

Extended

Event

Description

Expectation

Extended Event Description for TV1_SD

Following Event: TV1_SD has a parental rating of 15 years and its genre is classified as News/ Current Affairs or

Documentary.

1.2.12

1.2.13 Using numerical keys, press '209' to enter service LCN 209 TV2_HD.

Rating 15 years

Service Name TV2_HD

1.2.14 Access the banner and check the present (now) event information.

1.2.15

1.2.16 Note: The event description may optionally be truncated by receiver

1.2.17 when the character length exceeds the allocated area for display of event

description.

Event start and end time

Event name

Short Event

Description

Extended

Event

Description

Thursday 12 th

April 2012

21:00:00 - 21:30:00 (30 minutes).

TV2_HD Present Event

Short Event Description for TV2_HD

Present Event.

Extended Event Description for TV2_HD

Present Event: TV2_HD has a parental rating of 11 years and its genre is classified as Show/ Game Show or

Variety Show.

Ref.

3.2.12

3.2.12.1

Result Remarks

34

MCMC MTSFB TC T011:2014

6.4.1.3 Codec Information

Section 1.3 : Codec Information

No. Test Instruction

1.3.1 Play out MYS_SIPSI_1a.ts and perform receiver full scan.

1.3.2 Using numerical keys, press '208' to enter service LCN 208 TV1_SD.

1.3.3 Using numerical keys, press '209' to enter service LCN 209 TV2_HD.

Video

Component

Audio

Component

Video

Component

Expectation

The 576i (16:9) MPEG-4 AVC MP@L3 SD

“Flowers" video shall be presented.

"Guitar Solo" audio shall be selectable when the audio selection is set to English.

The 1080i MPEG-4 AVC MP@L4 HD

"Village" video shall be presented.

1.3.4 Using numerical keys, press '210' to enter service LCN 210 TV3_HD.

Video

Component

The 720p MPEG-4 AVC MP@L4 HD

"Park" video shall be presented.

1.3.5 Using numerical keys, press '211' to enter service LCN 211 TV4_SD.

Video

Component

The 576i (4:3) MPEG-4 AVC MP@L3 SD

"Bridge" video shall be presented.

1.3.6 Play out ChID_voices_swp_ddp_DVB_ h264_25fps.trp and perform receiver full scan. Enter Service Dolby Labs Test

Stream

Audio

Component

Audio alternates between each channel should be presented.

Note: Audio presentation is optional.

Ref.

3.2.3

3.2.3.1

3.2.3.2

3.2.4

3.2.4.1

3.2.3

3.2.3.1

3.2.3.2

3.2.3

3.2.3.1

3.2.3.2

3.2.3

3.2.3.1

3.2.3.2

3.2.4

3.2.4.1

Result Remarks

35

MCMC MTSFB TC T011:2014

6.4.1.4 Audio and Subtitle Language

Section 1.4 : Audio and Subtitle Language

No. Test Instruction

1.4.1 Play out MYS_SIPSI_1a.ts and perform receiver full scan.

Enter Service TV_SD

1.4.2 Firstly, perform the following setting:

Enable Subtitles

Audio

Subtitle

1.4.3 Note 1: All subtitles presented are in

English.

1.4.4 Note 2: If subtitles do not display due to PTS-PCR difference, then subtitle

tests can be considered a PASS.

1.4.5 Please indicate in Remarks if this is the case, and also ensure to make selfdeclaration in section 7.1 regarding the

Display of Subtitles

1.4.6

1.4.7

Audio

Subtitle

Audio

Subtitle

Audio

Expectation

"Keyboard" audio shall be selectable when the audio selection is set to Bahasa

Melayu (MSA).

Bahasa Melayu subtitles, “SIPSI Test.

Subtitle 1, number…” shall be selectable when the subtitle selection is set to

Bahasa Melayu (MSA).

"Bell rings" audio shall be selectable when the audio selection is set to Chinese

(ZHO).

Chinese subtitles, “SIPSI Test. Subtitle 2, number…", shall be selectable when the subtitle selection is set to Chinese (ZHO).

"Drum Solo" audio shall be selectable when the audio selection is set to Tamil

(TAM).

Tamil subtitles, “SIPSI Test. Subtitle 3, number…” shall be selectable when the subtitle selection is set to Tamil (TAM).

"Guitar Solo" audio shall be selectable when the audio selection is set to English.

Ref.

3.2.4

3.2.4.1

3.2.6.2

3.2.5

3.2.6.1

3.2.4

3.2.4.1

3.2.6.2

3.2.5

3.2.6.1

3.2.4

3.2.4.1

3.2.6.2

3.2.5

3.2.6.1

3.2.4

3.2.4.1

3.2.6.2

Result Remarks

36

MCMC MTSFB TC T011:2014

Section 1.4 : Audio and Subtitle Language

No. Test Instruction

1.4.8

1.4.9

1.4.10

1.4.11 Enter Service TV2_HD.

Firstly, perform the following settings :

- Enable Subtitles

Subtitle

Audio

Subtitle

Audio

Expectation

English subtitles, "SIPSI Test. Subtitle 0, number…", shall be selectable when the subtitle selection is set to English.

Receiver shall present any of the following audio components when the audio selection is set to other languages besides

Bahasa Melayu, English, Chinese and

Tamil:

English (ENG) - "Guitar Solo"

Bahasa Melayu (MSA) - "Keyboard"

Chinese (ZHO) - "Bell rings"

Tamil (TAM) - "Drum Solo"

Receiver shall present any of the following subtitle components when the subtitle selection is set to other languages besides

Bahasa Melayu, English, Chinese and

Tamil:

English (ENG) Subtitles

Bahasa Melayu (MSA) Subtitles

Chinese (ZHO) Subtitles

Tamil (TAM) Subtitles

"Birds" audio shall be selectable when the audio selection is set to Original Audio

(QAA).

Ref.

3.2.5

3.2.6.1

3.2.4

3.2.4.1

3.2.6.2

3.2.5

3.2.6.1

3.2.4

3.2.4.1

Result Remarks

37

MCMC MTSFB TC T011:2014

6.4.1.5 Results of Basic SI/PSI Test

Results of Basic SI/PSI Test

Number of Passes

Number of Fails

Number of Not Tested

Total test items

6.4.2 Logical Channel Numbering (LCN) Test

Description

This test contains the following sections:

Section 2.1 : Decoding of LCN descriptors

2.1.1 LCN V1 Descriptors

2.1.2 LCN V2 Descriptors

Section 2.2 : Foreign Services

Section 2.3 : No LCN Descriptor

Section 2.4 : Regional Broadcast Management

Note :

Reference Document (Ref.) : SKMM MTSFB TC

T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver.

Test Streams :

MYS_SIPSI_2.1a.ts

MYS_SIPSI_2.1b.ts

MYS_SIPSI_2.3.ts

FGN_SIPSI_2.2.ts

FGN_SIPSI_2.3.ts

MYS_SIPSI_2.4.ts

Note :

The Test Streams are available with the

Communication and Multimedia Certification

Section, SIRIM QAS International Sdn Bhd

Stream Configuration :

Modulation Type : DVB-T2

Channel Frequency : 474 MHz - 858 MHz

Bandwidth : 8 MHz

Mode : 32K

Guard Interval : 1/128

Modulation : 256 QAM

Cell Identifier : 0

Note:

In the case of simultaneous playing of two streams, the streams should be played out at different frequencies.

For example, one stream is played out at 474 MHz and the other is played out at 858 MHz.

38

MCMC MTSFB TC T011:2014

6.4.2.1 Decoding of LCN descriptors

Section 2.1 : Decoding of LCN descriptors

No.

Test

Category

2.1.1 LCN V1 descriptors

Instructions

Play out

MYS_SIPSI_2.1a.ts and perform receiver auto scan.

Expectations

Total of 6 services shall be visible in the service list and shall be in ascending order as below:

LCN 010 MYS_TV 1

LCN 031 MYS_TV 4.1/MYS_TV 4.2

LCN 561 MYS_Radio 9

LCN 800++ MYS_TV 4.1/MYS_TV 4.2

LCN 800++ MYS_TV 6

LCN 800++ Service with no LCN

Confirm that receiver shall be able to access each service normally via numeric button and service list.

Using numerical keys, press '102' to enter service LCN 102

MYS_Radio 8.

'Drum Solo' audio shall be presented.

This service is hidden and can only be selected using direct key entry.

Using numerical keys, press '031' to enter service LCN 031 MYS_TV

4.1/ or MYS_TV 4.2.

'Bridge' video and 'Keyboard' audio shall be presented.

Select 'Service with no LCN' service.

LCN 800++ shall be assigned to this service.

'Bridge' video and 'Guitar Solo' audio shall be presented.

Ref.

3.2.11.2

3.2.11.4

3.2.19

Result Remarks

39

MCMC MTSFB TC T011:2014

Section 2.1 : Decoding of LCN descriptors

No.

Test

Category

2.1.2 LCN V2 descriptors

Instructions

Play out

MYS_SIPSI_2.1b.ts and perform receiver auto scan.

Expectations

Total of 6 services shall be visible in the service list and shall be in ascending order as below:

LCN 005 TV5

LCN 055 TV55_A

LCN 166 Radio 5

LCN 800++ TV 55_B

LCN 800++ TV 132

LCN 800++ Service with no LCN

Service with LCN 300 is hidden and shall not appear in the service list.

Confirm that receiver is able to access each service normally via numerical keys.

Using numerical keys, press '300' to enter service LCN 300 Radio7.

This service is hidden and can only be selected using direct key entry.

'Drum Solo' audio shall be presented.

Using numerical keys, press '055' to enter service LCN 055 TV55_A.

'Bridge' video and 'Keyboard' audio shall be presented.

Select 'Service with no LCN' service.

LCN 800++ shall be assigned to this service.

'Bridge' video and 'Guitar Solo' audio shall be presented.

Ref.

3.2.11.3

3.2.11.4

3.2.19

Result Remarks

40

MCMC MTSFB TC T011:2014

6.4.2.2 Foreign Services

Section 2.2 : Foreign Services

No.

Test

Category

Instructions

2.2.1 Foreign

Service

Play out

MYS_SIPSI_2.1b.ts and

FGN_SIPSI_2.2.ts simultaneously and perform receiver's auto scan method.

Note: Please refer to the stream configuration method as stated above

Expectations

Total of 12 services shall be visible in the service list and shall be an ascending order as below:

LCN 005 TV 5

LCN 055 TV 55_A/TV 55_B

LCN 166 Radio 5

LCN 800++ TV 55_A/TV 55_B

LCN 800++ TV 132

LCN 800++ Service with no LCN

LCN 800++ SI Television 100

LCN 800++ TV Service 101

LCN 800++ TV Service 102

LCN 800++ MI Television 201

LCN 800++ MI Television 202

LCN 800++ LL Television 300

Confirm that receiver is able to access to each service normally via numerical keys and service list.

Service with LCN 300 is hidden and shall not appear in the service list.

Confirm that receiver is able to access each service normally via numerical keys.

Using numerical keys, press '300' to enter service LCN 300 Radio7.

This service is hidden and can only be selected using direct key entry.

'Drum Solo' audio shall be presented.

Confirm that all of the foreign services are assigned with channel number

800++.

Ref.

3.2.11.4

3.2.19

Result Remarks

41

MCMC MTSFB TC T011:2014

6.4.2.3 No LCN Descriptor

Section 2.3 : No LCN Descriptor

No.

Test

Category

2.3.1 No LCN

Descriptor

Instructions

Play out

MYS_SIPSI_2.3.ts and

FGN_SIPSI_2.3.ts simultaneously and perform receiver's auto scan method.

Expectations

Total of 12 services shall be visible in the service list and shall be an ascending order as below:

LCN 001 TV 5

LCN 002 TV 55_A

LCN 003 Radio 5

LCN 004 Radio 7

LCN 005 TV 55_B

LCN 006 TV 132

LCN 007 SI Television 100

LCN 008 TV Service 101

LCN 009 TV Service 102

LCN 010 MI Television 201

LCN 011 MI Television 202

LCN 012 LL Television 300

Confirm that receiver is able to access each service normally via numerical keys and service list.

Ref.

3.2.11.4

3.2.19

Result Remarks

42

MCMC MTSFB TC T011:2014

6.4.2.4 Regional Broadcast Management

Section 2.4 : Regional Broadcast Management

No.

Test

Category

Instructions

2.4.1 Regional

Broadcast

Management

Play out

MYS_SIPSI_2.4.ts and perform receiver auto scan.

1. Select the channel list for Central

Region

(ID : 0x0001) in the receiver's

Expectations

Total of 9 services shall be visible in the service list and shall be in ascending order as below for the Central Region channel list

(ID:0x0001)

LCN 001 MY_TV 1

LCN 005 MY_TV 15

LCN 007 MY_TV 2

LCN 033 MY_HDTV 4

LCN 155 MYTV_10

LCN 431 MY Radio 6

LCN 611 MY_TV 5

LCN 701 MY_TV 7

LCN 800++ MY_TV 8

Confirm that receiver is able to access each service normally via numerical keys and service list

Note: Data type service is optional.

Ref.

3.2.11.5

3.2.19

Result Remarks

43

MCMC MTSFB TC T011:2014

Section 2.4 : Regional Broadcast Management

No.

Test

Category

Instructions

2. Perform receiver auto scan again and select the channel list for

Southern region

(ID : 0x0002) in the receiver's channel list menu.

Expectations

Total of 9 services shall be visible in the service list and shall be in ascending order as below for the Southern Region channel list

(ID:0x0002)

LCN 002 MY_TV 2

LCN 006 MY_TV 15

LCN 010 MY_TV 1

LCN 036 MY_HDTV 4

LCN 105 MYTV_10

LCN 437 MY_Radio 6

LCN 617 MY_TV 5

LCN 770 MY_TV 7

LCN 800++ MY_TV 8

Confirm that receiver is able to access each service normally via numerical keys and service list.

Note: Data type service is optional.

6.4.2.5 Results of LCN Test

Results of LCN Test

Number of Passes

Number of Fails

Number of Not Tested

Total test items

Ref.

3.2.11.5

3.2.19

Result Remarks

44

MCMC MTSFB TC T011:2014

6.4.3 Network Evolution

Description

This test contains the following sections:

Section 3.1 : Service Addition and Deletion

Section 3.2 : Clash LCN Resolution

Section 3.3 : Multiplex Addition and Deletion

Section 3.4 : Service and Event Updates

Note :

Reference Document (Ref.): SKMM MTSFB TC

T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver.

Test Streams :

MYS_SIPSI_3.1a.ts

MYS_SIPSI_3.1a_addition.ts

MYS_SIPSI_3.1a_deletion.ts

MYS_SIPSI_3.2a.ts

MYS_SIPSI_3.2b.ts

MYS_SIPSI_3.2a_02.ts

MYS_SIPSI_3.2b_01.ts

MYS_SIPSI_3.2b_02.ts

MYS_SIPSI_3.3a.ts

MYS_SIPSI_3.3a_mux.ts

MYS_SIPSI_3.3b_mux.ts

MYS_SIPSI_3.5.ts

Note :

The Test Streams are available with the

Communication and Multimedia Certification

Section, SIRIM QAS International Sdn Bhd

Stream Configuration :

Modulation Type : DVB-T2

Channel Frequency : 474 MHz - 858 MHz

Bandwidth : 8 MHz

Mode : 32K

Guard Interval : 1/128

Modulation : 256 QAM

Cell Identifier : 0

Note:

In the case of simultaneous playing of two streams, the streams should be played out at different frequencies. For example, one stream is played out at

474 MHz and the other is played out at 858 MHz.

45

MCMC MTSFB TC T011:2014

6.4.3.1 Service Addition and Deletion

Section 3.1 : Service Addition and Deletion

No. Instruction

3.1.1 Play out MYS_SIPSI_3.1a.ts and perform receiver auto scan.

Expectation

A total of 4 services shall be presented as follows in ascending order:

LCN 005 MY_TV Channel 1

LCN 013 MY_ Radio Channel 5

LCN 166 MY_TV Channel 11

LCN 180 MY_TV Channel 17

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

At interval 0::121, same services shall be displayed in the service list as

Ref. 3.1.1.

3.1.2 Stop MYS_SIPSI_3.1a.ts and play out

3.1.3

MYS_SIPSI_3.1a_addition.ts at the same frequency as before.

Note : Do not perform auto scan

Network update shall start within the interval 121::240.

Receiver shall automatically undergo network update and update the service list.

A total of 6 services shall be presented in the service list as follows in ascending order:

LCN 005 MY_TV Channel 1

LCN 013 MY_ Radio Channel 5

LCN 166 MY_TV Channel 11

LCN 180 MY_TV Channel 17

LCN 290 MY_Radio Channel 32

LCN 351 MYS_TV Channel 106

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

Ref.

3.2.11.6

Result Remarks

46

MCMC MTSFB TC T011:2014

Section 3.1 : Service Addition and Deletion

No. Instruction

3.1.4 Next, stop

MYS_SIPSI_3.1a_addition.ts and play out

MYS_SIPSI_3.1a.ts again.

Perform receiver auto scan.

Expectation

A total of 4 services shall be presented as follows in ascending order:

LCN 005 MY_TV Channel 1

LCN 013 MY_ Radio Channel 5

LCN 166 MY_TV Channel 11

LCN 180 MY_TV Channel 17

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

At interval 0::121, same services shall be displayed in the service list as

Ref. 3.1.4.

3.1.5 Stop MYS_SIPSI_3.1a.ts and play out

3.1.6

MYS_SIPSI_3.1a_deletion.ts at the same frequency as before

Note : Do not perform auto

scan

Network update shall start within the interval 121::240.

Receiver shall automatically undergo network update and update the service list.

Confirm that 2 services are deleted from the service list and the remaining service presented in the service list are as follows in ascending order:

LCN 005 MY_TV Channel 1

LCN 013 MY_ Radio Channel 5

Confirm that receiver is able to access each service normally via numerical keys and service list.

Ref.

3.2.11.6

Result Remarks

47

MCMC MTSFB TC T011:2014

6.4.3.2 Clash LCN Resolution

Section 3.2 : Clash LCN Resolution

No. Instruction

3.2.1 Play out MYS_SIPSI_3.2a.ts and MYS_SIPSI_3.2b.ts simultaneously and perform receiver auto scan method.

Expectation

Total of 9 services shall be visible in the service list and shall be an ascending order as below:

LCN 100 Service_TV1_SD

LCN 101 Service_TV2_SD

LCN 102 Service_TV3_SD

LCN 103 Service_Radio1

LCN 104 Service_Radio2

LCN 111 SD Service 1

LCN 222 SD Service 1_muxB

LCN 333 SD Service 2_muxB

LCN 444 SD Service 2

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

Using numerical keys, press '222' to enter LCN 222 SD Service

1_muxB.

'Bridge' video and 'Bell Ring' audio shall be presented.

Commence following test from LCN 222 SD Service 1_muxB.

Ref.

3.2.11.6

Result Remarks

48

MCMC MTSFB TC T011:2014

Section 3.2 : Clash LCN Resolution

No. Instruction

3.2.2 Stop the streams and play out

MYS_SIPSI_3.2a_02.ts and

MYS_SIPSI_3.2b_01.ts simultaneously at the same frequency as before.

Set power of Set the power of multiplex to be such that

MYS_SIPSI_3.2b_01.ts >

MYS_SIPSI_3.2a_02.ts

Note: Do not perform receiver auto scan.

Expectation

Perform receiver method of network configuration update.

Ensure the following services shall be listed :

LCN 100 Service_TV1_SD

LCN 101 Service_TV2_SD

LCN 102 Service_TV3_SD

LCN 103 Service_Radio1

LCN 104 Service_Radio2

LCN 111 SD Service 1

LCN 222 SD Service 1_muxB

LCN 333 SD Service 2_muxB

LCN 444 SD Service 2

LCN 555 Service_Radio10

LCN 666 Service_TV7_SD

LCN 800++ SD_Service 2_muxA

Using numerical keys, press '333', '555', and '666', and ensure the following components are available in the services :

In LCN 333, 'Bell Ring' audio and 'Bridge' video shall be presented.

In LCN 555, 'Keyboard' audio and 'Flowers' video shall be presented.

In LCN 666, 'Keyboard' audio and 'Flowers' video shall be presented.

Ref.

3.2.11.6

Result Remarks

49

MCMC MTSFB TC T011:2014

Section 3.2 : Clash LCN Resolution

No. Instruction

3.2.3 Stop the streams and play out

MYS_SIPSI_3.2a_02.ts and

MYS_SIPSI_3.2b_02.ts simultaneously at the same frequency as before.

Note :

Do not perform receiver auto scan.

Please refer to the stream configuration method as stated

above

Expectation

Perform receiver method of network configuration update.

Ensure that the following is displayed :

LCN 100 Service_TV1_SD

LCN 101 Service_TV2_SD

LCN 102 Service_TV3_SD

LCN 103 Service_Radio1

LCN 104 Service_Radio2

LCN 222 SD Service 1_muxB

LCN 444 SD Service 2

LCN 555 Service_Radio10

LCN 666 Service_TV7_SD

LCN 800++ SD Service 2_muxA

Ensure that the below services are removed :

1. LCN 111 SD Service 1

2. LCN 333 SD Service 2_muxB

Ref. Result Remarks

3.2.11.6

50

MCMC MTSFB TC T011:2014

6.4.3.3 Multiplex Addition and Deletion

Section 3.3 : Multiplex Addition and Deletion

No. Instruction

3.3.1 Static Multiplex Addition

Play out MYS_SIPSI_3.3a.ts and perform receiver auto scan.

3.3.2 Stop MYS_SIPSI_3.3a and play out MYS_SIPSI_3.3a_mux.ts and MYS_SIPSI_3.3b_mux.ts simultaneously.

Expectation

A total of 6 services shall be presented as follows in ascending order:

LCN 001 - TV1

LCN 002 - TV2

LCN 003 - TV3

LCN 004 - TV4

LCN 005 - TV5

LCN 006 - Radio6

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

Using numerical keys, press '001' to enter LCN 001 TV1.

'Flowers' video and 'Guitar Solo' audio shall be presented.

Commence following test from LCN001 TV1.

Perform receiver method of network configuration update.

(Note: Do not perform receiver autoscan.)

A total of 10 services shall be presented as follows in ascending order:

LCN 001 - TV1

LCN 002 - TV2

LCN 003 - TV3

LCN 004 - TV4

LCN 005 - TV5

LCN 006 - Radio6

LCN 100 - TV11

LCN 200 - TV_12

LCN 501 - TV_15

LCN 502 - Radio 17

Ref.

3.2.11.6

3.2.11.6

Result Remarks

51

MCMC MTSFB TC T011:2014

Section 3.3 : Multiplex Addition and Deletion

No. Instruction

3.3.3 Multiplex Deletion/Addition

Next, stop above streams and play out MYS_SIPSI_3.3a.ts at frequency 474 MHz and perform auto scan.

3.3.4 Stop MYS_SIPSI_3.3a.ts and change the frequency to

858MHz.

Perform receiver method of service update.

Expectation

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

Using numerical keys, press '001' to enter LCN 001 TV1.

'Flowers' video and 'Guitar Solo' audio shall be presented.

A total of 6 services shall be presented as follows in ascending order:

LCN001 - TV1

LCN002 - TV2

LCN 003 - TV3

LCN 004 - TV4

LCN 005 - TV5

LCN 006 - Radio6

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

A total of 6 services shall be presented as follows in ascending order:

LCN001 - TV1

LCN002 - TV2

LCN 003 - TV3

LCN 004 - TV4

LCN 005 - TV5

LCN 006 - Radio6

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

Ref.

3.2.11.6

3.2.11.6

Result Remarks

52

MCMC MTSFB TC T011:2014

6.4.3.4 Service and Event Updates

Section 3.4 : Service and Event Updates

No. Instruction

3.4.1 Play out MYS_SIPSI_3.5.ts and perform receiver auto scan.

Expectation

Using numerical keys, press '120' to enter LCN120 TV Channel 120.

At interval 0::60s, 'Village' video with 'Keyboard' audio shall be presented.

Ensure no juddering or erroneous effects in components during presentation.

At interval 61::180s, audio and video shall stop. Receiver may optionally freeze the last image of the video during this interval.

Note: Receiver shall handle clean transitions into and out of the active and inactive states during the interval 60-61s.

Ref.

3.2.2.1

Result Remarks

53

MCMC MTSFB TC T011:2014

Section 3.4 : Service and Event Updates

No. Instruction

3.4.2

Expectation

Using numerical keys, press '131' to enter LCN131 TV Service 131.

At interval 0::60s, no components shall be presented.

At interval 61::180s, 'Park' video with 'Bell rings' audio shall be presented.

Ensure no juddering or erroneous effects in components during presentation.

Note: Receiver shall handle clean transitions into and out of the active and inactive states during the interval 60-61s.

Using numerical keys, press '131' to enter LCN131 TV Service 131.

At interval 0::60s, no components shall be presented.

At interval 61::180s, 'Park' video with 'Bell rings' audio shall be presented.

Ensure no juddering or erroneous effects in components during presentation.

Note: Receiver shall handle clean transitions into and out of the active and inactive states during the interval 60-61s.

Ref.

3.2.2.1

Result Remarks

54

MCMC MTSFB TC T011:2014

Section 3.4 : Service and Event Updates

No. Instruction

3.4.3

Expectation

Using numerical keys, press '555' to enter LCN555 Channel 266.

Press ‘Info' key to view 'Now' and 'Next' event information at banner and optionally at other user interface.

Ensure the event information is as in expectations below and take note of the changes of this information at interval 61s.

At interval 0::60s, present event information are as follows:

Event Name : News at TV1

Event Start/End Time: 9 April, 5:30 PM - 6:30 PM

Event Description: News programme on air.

Rating: Not defined

At interval 61s, receiver shall detect version change in event p/f and event p/f information shall be updated accordingly.

Present event information during interval 61::180s shall be presented as follows:

Event Name : Movie programme

Event Start/End Time: 9 April, 6:30 PM - 8:00 PM

Event Description: Movie programme on air.

Rating: Not defined

Ref.

3.2.12.1

Result Remarks

55

MCMC MTSFB TC T011:2014

6.4.3.5 Results of Network Evolution Test

Results of Network Evolution Test

Number of Passes

Number of Fails

Number of Not Tested

Total test items

6.4.4 Character Test

Description

This test contains the following sections:

Section 4.1 : Event p/f

Section 4.2 : Event Schedule

Section 4.3 : Event p/f (Huffman Encoding)

Section 4.4 : Event Schedule (Huffman Encoding)

Section 4.5 : Huffman Encoding (Malay)

Section 4.6 : Huffman Encoding (ESC character)

Section 4.7 : No Table Definition

Section 4.8 : Latin Table 05 ISO-8859-9

Note :

Reference Document (Ref.): SKMM MTSFB TC

T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver.

Test Streams :

MYS_CHAR_4a.ts

MYS_CHAR_4b.ts

MYS_CHAR_4c.ts

MYS_CHAR_4d.ts

MYS_CHAR_4e.ts

MYS_CHAR_4f.ts

Note :

The Test Streams are available with the

Communication and Multimedia Certification

Section, SIRIM QAS International Sdn Bhd

Stream Configuration :

Modulation Type : DVB-T2

Channel Frequency : 474 MHz - 858 MHz

Bandwidth : 8 MHz

Mode : 32K

Guard Interval : 1/128

Modulation : 256 QAM

Cell Identifier : 0

56

MCMC MTSFB TC T011:2014

6.4.4.1 Event p/f

Section 4.1 : Event p/f

No. Test instructions

4.1.1 Play out stream

MYS_CHAR_4a.ts and perform receiver auto scan method.

Enter each service.

4.1.2 Using numerical keys, press '100' to

4.1.3 enter service LCN

100 Test 1: Normal

Encoding Character.

Access the banner

4.1.4 and guide to view the present (now) event information.

Access the following events on the banner.

Checkpoints

Ensure all services are populated correctly as in expectation. Ensure services are accessible via numerical keys. Confirm correct service name and LCN numbering in each service.

Ensure all present event descriptions are presented as in expectations in the

EPG.

Expectations

LCN 100 Test 1: Normal Encoding Character LCN 101

Test 2: Normal Encoding Character LCN 102 Test 3:

Normal Encoding Character

Event Name "Event 1: Combination of long event name which consists many letter and number ranges 12abc"

Note: Some truncation might occur.

Short Event

Description

"Short Event Description: In 1987, statistics show that 43 percent of people in the world aged between 18 to 35 smoke 25 cigarettes per day. This is bad news."

Extended

Event

Description

"Extended Description: Cigarettes contain a chemical called carcinogen which could endanger the human lungs.

Not only does this endanger the smokers, this could be harmful to others as well for they are inhaling the smoke through second hand smoking."

Note: Some truncation might occur.

Ref.

3.2.8

Result Remarks

57

MCMC MTSFB TC T011:2014

Section 4.1 : Event p/f

No.

4.1.5

4.1.6

Test instructions Checkpoints

Ensure all following events are presented as in expectations in the EPG

Expectations

Short Event

Description

Extended

Event

Description

"Short Event Description: Zebras have many black stripes. It is said that they come from a species of the African horse family."

"Extended Event Description: They are united by their distinctive black and white stripes which come in different patterns and are unique to each individual."

Note: Some truncation might occur.

Event Name "Event 1 : Character Test"

Ref.

4.1.7 Using numerical keys, press '101' to enter service

LCN101

4.1.8 Test 2: Normal

Encoding Character.

Ensure all present event descriptions are presented as in expectations in the

EPG.

4.1 .9 Access the banner and guide to view the present (now) event information.

Access the following events on the banner

Short Event

Description

Extended

Event

Description

"CAPITAL ALPHABET:

ABCDEFGHIJKLMNOPQRSTUVWXYZ

Numbers: 0123456789. abcdefghijklmnopqrstuvwxyz"

“SIX OF THE WOMEN QUIETLY GAVE

BACK PRIZES TO THE JUDGE. THE

JUDGE QUICKLY GAVE BACK SIX

PRIZES TO THE WOMEN. Six of the women quietly gave back prizes to the judge. The judge quickly gave back six prizes to the women.”

Note: Some truncation might occur.

3.2.8

Result Remarks

58

MCMC MTSFB TC T011:2014

Section 4.1 : Event p/f

No.

4.1.10

4.1.11

4.1.12

Test instructions Checkpoints

Ensure all following events are presented as in expectations in the EPG.

4.1.13

4.1.14

Using numerical keys, press '102' to enter service

LCN102 Test 3:

Normal Encoding

Character.

Access the banner and guide to view the present (now) event information.

Ensure all present event descriptions are presented as in expectations in the

EPG

Expectations

Event Name "Event 2:CharacterTest123"

Short Event

Description

"THE BOY WORE A RED SHIRT. HE

WAS SEEN STROLLING IN THE ZOO

WHILE FEEDING THE FLAMINGOS

AND DUCKLINGS. HE WAS WITH HIS

FAMILY WHEN SUDDENLY AN

UNPREDICTED WEATHER

OCCURRED. IT STARTED DRIZZLING

BEFORE A HEAVY DOWNPOUR

CAME."

Extended

Event

Description

"The boy wore a red shirt. He was seen strolling in the zoo while feeding the flamingos and ducklings. He was with his family when suddenly an unpredicted weather occurred. It started drizzling before a heavy downpour came."

Note: Some truncation might occur.

Event Name "Event 1 : Test NBSP and SHY code in description"

Short Event

Description

"NBSP : word abc word abc word abc word abc word abc word abc word abc word abc word abc word abc word abc word abc word abc word abc word abc word abc SHY : worddef worddef"

Pass Criteria’s:

1. For NBSP, the line may only be broken after word “abc” such that

“word abc” is kept together.

Ref.

3.2.8

Result Remarks

59

MCMC MTSFB TC T011:2014

Section 4.1 : Event p/f

No. Test instructions Checkpoints Expectations

2. For SHY, the word should be broken at the [SHY] Character position when the line needs to wrap and display a hyphenation Character “-”, when no line wrap occurs then the [SHY] is not presented. Receivers not implementing SHY are likely to display a single line.

Ref.

6.4.4.2 Event Schedule

Section 4. 2 : Event Schedule

No. Test instructions Checkpoints Expectations

4.2.1 Using numerical keys, press '101' to enter service LCN

101 Test 2: Normal

Encoding Character.

Press the Guide button to access the

EPG information.

4.2.2 Toggle keys to continue to next day event schedule and previous days.

Ensure EPG is accessible.

Ensure 7 days of EPG are displayed.

EPG is able to be presented when Guide key is pressed.

7 days of Event Schedule shall be presented. If less than 7 days of Event Schedule is accessed, this test shall fail.

Ref.

3.2.8

3.2.12.2

Result

Result

Remarks

Remarks

60

MCMC MTSFB TC T011:2014

Section 4. 2 : Event Schedule

No. Test instructions

4.2.3 Check the service names on the EPG.

Checkpoints Expectations

Ensure services are correct. All services shall be populated in the EPG with the same details as in expectations in Section 4.1.1

4.2.4 Toggle up, down, left, right keys

4.2.5 Select Event 3 in

LCN 101.

4.2.6

4.2.7

4.2.8

4.2.9

4.2.10

Select Event 4 in

LCN 101

4.2.11 Select Event 5 in

4.2.12

4.2.13

LCN 101

Ensure EPG is interactive with different key press.

No erroneous effects occur during different key press.

Ensure correct Event

Names, Event Description, and Event Start and End

Times are presented as in expectation.

Ensure correct Event

Names, Event Description, and Event Start and End

Times are presented as in expectation

Event Name "Event 3 : Characters Row A-B-C"

Short Event

Description

Extended

Event

Description

"¡¢£€¥§¤‘“«←↑→↓°±²³×µ¶·÷’”»¼½¾¿"

" "

Event Name "Event 4 : Characters Row D-E"

Short Event

Description

Extended

Event

Description

"―¹®©™♪¬¦⅛⅜⅝⅞ΩÆÐᵃĦIJĿŁØŒ

Ŋʼn"

"Event information is not available."

Event Name "Event 5 : Characters Row F"

⁰ ÞŦ

Ensure correct Event

Names, Event Description, and Event Start and End

Times are presented as in expectation

Short Event

Description

Extended

Event

Description

"ĸæđðħıijŀłøœßþŧŋ"

"Event information is not available."

Ref.

3.2.8

3.2.12.2

Result Remarks

61

MCMC MTSFB TC T011:2014

6.4.4.3 Event p/f (Huffman Encoding)

Section 4.

3 : Event p/f (Huffman Encoding)

No. Test instructions

4.3.1 Play out stream

MYS_CHAR_4b.ts and perform receiver auto scan method.

Enter each service.

Checkpoints

Ensure all services are populated correctly as in expectation. Ensure services are accessible via numerical keys. Confirm correct service name and LCN numbering in each service.

Expectations

4.3.2 Using numerical keys, press '100' to enter service LCN

100

4.3.3 Test 1: Huffman

Encoding Character.

Ensure all present event descriptions are presented as in expectations in the banner and the EPG

Event Name "Event 1 : Combination of long event name which consists many letter and number ranges 12abc"

Short Event

Description

"Short Event Description: In 1987, statistics show that 43 percent of people in the world aged between18 to 35 smoke 25 cigarettes per day. This is bad news."

4.3.4 Access the banner and guide to view the present (now) event information.

Access the following events on the banner.

Extended

Event

Description

"Extended Description: Cigarettes contain a chemical called carcinogen which could endanger the human lungs.

Not only does this endanger the smokers, this could be harmful to others as well for they are inhaling the smoke through second hand smoking."

Note: Some truncation might occur.

Ref.

3.2.8

Result Remarks

62

MCMC MTSFB TC T011:2014

Section 4.

3 : Event p/f (Huffman Encoding)

No. Test instructions Checkpoints

4.3.5 Ensure all following events are presented as in expectations in the banner and the EPG

Short Event

Description

Expectations

"Short Event Description: Zebras have many black stripes. It is said that they come from a species of the African horse family."

4.3.6 Extended

Event

Description

"Extended Event Description: They are united by their distinctive black and white stripes which come in different patterns and are unique to each individual."

Note: Some truncation might occur.

4.3.7 Using numerical keys, press '101' to enter

LCN101 service

4.3.8 Test 2: Huffman

Encoding Character.

Ensure all present event descriptions are presented as in the banner and the

EPG.

Event Name "Event 1 : Character Test"

Short Event

Description

"CAPITAL ALPHABET:

ABCDEFGHIJKLMNOPQRSTUVWXYZ

Numbers: 0123456789. abcdefghijklmnopqrstuvwxyz."

4.3.9 Access the banner and guide to view the present (now) event information.

Access the following events on the banner

Extended

Event

Description

“SIX OF THE WOMEN QUIETLY GAVE

BACK PRIZES TO THE JUDGE. THE

JUDGE QUICKLY GAVE BACK SIX

PRIZES TO THE WOMEN. Six of the women quietly gave back prizes to the judge. The judge quickly gave back six prizes to the women.”

Note: Some truncation might occur.

Ref.

3.2.8

Result Remarks

63

MCMC MTSFB TC T011:2014

Section 4.

3 : Event p/f (Huffman Encoding)

No. Test instructions Checkpoints

4.3.10

4.3.11

Expectations

Ensure all following events are presented as in expectations in the banner and the EPG

Event Name "Event 2 : CharacterTest123"

Short Event

Description

"THE BOY WORE A RED SHIRT. HE

WAS SEEN STROLLING IN THE ZOO

WHILE FEEDING THE FLAMINGOS

AND DUCKLINGS. HE WAS WITH HIS

FAMILY WHEN SUDDENLY AN

UNPREDICTED

OCCURRED."

WEATHER

4.3.12 Extended

Event

Description

"The boy wore a red shirt. He was seen strolling in the zoo while feeding the flamingos and ducklings. He was with his family when suddenly an unpredicted weather occurred. It started drizzling before a heavy downpour came."

Note: Some truncation might occur.

4.3.13 Using numerical keys, press '102' to enter service

LCN102

4.3.14 Test 3: Huffman

Encoding Character.

Access the banner and guide to view the present (now) event information.

Ensure all present event descriptions are presented as in expectations in the banner and the EPG

Event Name "Huffman English"

Short Event

Description

"This is a verification test for English

Huffman Encoding. If this text appears, then the encoding is successful."

Ref.

3.2.8

3.2.8

Result Remarks

64

MCMC MTSFB TC T011:2014

6.4.4.4 Event Schedule (Huffman Encoding)

Section 4.

4 : Event Schedule (Huffman Encoding)

No. Test instructions

4.4.1 Using numerical keys, press '101' to enter.

Service LCN

101

Test 2: Huffman

Encoding Character.

Press the Guide button to access the

EPG information

Checkpoints Expectations

Ensure EPG is accessible. EPG is able to be presented when Guide key is pressed.

Ref.

4.4.2 Select Event 3 in LCN

101.

4.4.3

Ensure correct Event

Names, Event Description, and Event Start and End

Times are presented as in expectation.

Event Name "Event 3 : Huffman EPG 1"

Short Event

Description

"Zebras have many black stripes. It is said that they come from a species of the

African horse family. This text should display in the EPG with Huffman

Encoding implemented."

3.2.8

Result Remarks

4.4.4 Select Event 4 in LCN

101.

4.4.5

Event Name "Event 4 : Huffman EPG 2"

Short Event

Description

"In 1987, statistics show that 43 percent of people in the world aged between 18 to 35 smoke 25 cigarettes per day. This text should display in the EPG with

Huffman Encoding implemented."

65

MCMC MTSFB TC T011:2014

Section 4.

4 : Event Schedule (Huffman Encoding)

No. Test instructions

4.4.6 Select Event 5 in LCN

4.4.7

101.

Checkpoints Expectations

Event Name "Event 5 : Huffman EPG 3"

Short Event

Description

"The boy wore a red shirt. He was seen strolling in the zoo while feeding the flamingos and ducklings. This text should display in the EPG with Huffman

Encoding implemented."

6.4.4.5 Huffman Encoding (Malay)

Section 4.

5 : Huffman Encoding (Malay)

No. Test instructions Checkpoints

4.5.1 Play out stream

MYS_CHAR_4c.ts and perform receiver auto scan method.

Enter service.

4.5.2

4.5.3

Using numerical keys, press '100' to enter service LCN 100

Test 1: Huffman

Malaysia Service.

Ensure all services are populated correctly as in expectation. Ensure services are accessible via numerical keys. Confirm correct service name and

LCN numbering in each service.

Ensure all present event descriptions are presented as in expectations in the banner and the EPG.

Expectations

LCN 100 Huffman Malaysia Service

Event Name "Huffman Bahasa Malaysia"

Short Event

Description

"Ikuti berita perkembangan yang terkini memaparkan dan semasa termasuk berita ekonomi dan kewangan.

Rancangan khas khusus untuk tontonan anda persembahan daripada TV6.

Berhibur dengan kumpulan muzik tempatan dengan pilihan lagu-lagu."

Note: Some truncation might occur.

Ref.

3.2.8

Ref.

3.2.8

Result Remarks

Result Remarks

66

MCMC MTSFB TC T011:2014

Section 4.

5 : Huffman Encoding (Malay)

No. Test instructions

4.5.4 Access the banner and guide to view the present (now) event information.

Checkpoints

Extended

Event

Description

Expectations

"Istimewa Bersama Zaidi Zainal yang menyampaikan lagu-lagu popularnya.

Saksikan Rentak Juara 2010 Konsert

Peringkat Akhir untuk hiburan semua hanya di TV6. Nikmati klip-klip video tempatan pilihan peminat yang terdiri daripada pelbagai kaum dan etnik."

Note: Some truncation might occur.

6.4.4.6 Huffman Encoding (ESC character)

Section 4.6 : Huffman Encoding (ESC character)

No. Test instructions Checkpoints Expectations

4.6.1 Play out stream

MYS_CHAR_4f.ts and perform

Enter service.

4.6.2 Using numerical keys, press '100' to enter service LCN 100

4.6.3 Test 1: Huffman

Malaysia Service.

Ensure all services are populated correctly as in expectation. Ensure services are accessible via numerical keys. Confirm correct service name and

LCN numbering in each service.

LCN 100 Huffman Malaysia Service

Ensure all present event descriptions are presented as in expectations in the banner and the EPG.

Event Name "Huffman Bahasa Malaysia"

Short Event

Description

"RM10 adalah bersamaan dengan £2.05 atau ¥278.34"

Ref.

Ref.

3.2.8

3.2.8

Result Remarks

Result Remarks

67

MCMC MTSFB TC T011:2014

Section 4.6 : Huffman Encoding (ESC character)

No. Test instructions Checkpoints

4.6.4 Access the banner and guide to view the present (now) event information.

4.6.5 Access the following events on the banner.

Ensure all following events are presented as in expectations in the banner and the EPG.

Expectations

Event Name "Huffman English"

Short Event

Description

"RM10 adalah bersamaan dengan £2.05 atau ¥278.34"

Ref.

6.4.4.7 No Table Definition

Section 4.

7: No Table Definition

No. Test instructions

4.7.1 Play out stream

MYS_CHAR_4d.ts and perform receiver auto scan method.

Enter service.

Checkpoints

Ensure all services are populated correctly as in expectation. Ensure services are accessible via numerical keys. Confirm correct service name and

LCN numbering in each service.

Expectations

LCN 100 Test 1: No Table Defined

4.7.2 Using numerical keys, press '100' to enter service LCN 100

Ensure all present event descriptions are presented as in expectations in the banner and the EPG.

Event Name "Event 1 : No Table Defined"

Ref.

3.2.8

3.2.8

Result Remarks

Result Remarks

68

MCMC MTSFB TC T011:2014

Section 4.

7: No Table Definition

No. Test instructions

4.7.3 Test 1: No Character

Table. Access the banner and guide to view the present

(now) information. event

Checkpoints

Short Event

Description

Expectations

"ABC EFGHI LMNOPQ STUVWXY

0123 5 9abcdefghi klmnopqrstuvwxy z. '() +,-. :

¡¢£€¥§¤‘“«←↑→↓°±²³×µ¶·÷’”»¼½¾¿

―¹®©™♪¬¦⅛⅝⅞ΩÆÐᵃĦIJĿŁØ

Œ ⁰ ÞŦŊʼnĸæđðħıijŀłøœßþŧŋ"

6.4.4.8 Latin Table 05 - ISO-8859-9

Section 4.

8: Latin Table 05 - ISO-8859-9

No. Test instructions

4.8.1 Play out stream

MYS_CHAR_4e.ts and perform receiver auto scan method.

Enter service.

4.8.2 Using numerical keys, press '100' to enter service LCN 100 Test

1: Character Table 05

(ISO-8859-9).

Access the banner and guide to view the present (now) event information.

Checkpoints

Ensure all services are populated correctly as in expectation. Ensure services are accessible via numerical keys. Confirm correct service name and LCN numbering in each service

Ensure all present event descriptions are presented as in expectations in the banner.

Expectations

LCN 100 Test 1: Character Table 05 (ISO-8859-9)

Short Event

Description

"!"#$%&'()*+,./0123456789:;<=>?@

ABCDEFGHIJKLMNOPQRSTUVW

XYZ[\]^_`abcdefghijklmnopqrstuvwx yz{|}~¡¢£¤¥§¨©×«¬®¯°±²³´µ¶·¸¹°»¼

½¾¿ ÆÇÈÉÊËÌÍÎÏĞÑÒÓÔ

ÕÖ×ØÙÚÛÜİŞßàáâãåæçèéêëìíîïğñ

òóôõö÷øùúûüışÿ"

Ref.

3.2.8

Ref.

3.2.8

Result Remarks

Result Remarks

69

MCMC MTSFB TC T011:2014

6.4.4.9 Results of Character Test

Results of Character Test

Number of Passes

Number of Fails

Number of Not Tested

Total test items

6.4.5 Active Format Descriptor (AFD) Test

This test contains the following sections:

Section 5.1 : AFD Test

Note :

Reference Document (Ref.): SKMM MTSFB TC

T004:2013 - Specification for Digital Terrestrial

Television Broadcast Service Receiver.

Test Streams :

MYS_AFD.ts

Note :

The Test Streams are available with the

Communication and Multimedia Certification

Section, SIRIM QAS International Sdn Bhd

Stream Configuration :

Modulation Type : DVB-T2

Channel Frequency : 474 MHz - 858 MHz

Bandwidth : 8 MHz

Cell Identifier : 0

Guard Interval : 1/128

Mode : 32K

Modulation : 256 QAM

70

MCMC MTSFB TC T011:2014

6.4.5.1 AFD

Section 5.1 : AFD

No. Test instructions

5.1.1 Play out stream

MYS_AFD.ts and perform receiver auto scan method

Note: Configure the receiver screen setting to display the video as coded frame.

Checkpoints

Ensure all services appear in the service list.

5.1.2 Enter service 'AFD

(1000)' by pressing

100.

LCN 100 AFD (1000)

LCN 200 AFD (1011)

LCN 300 AFD (1001)

Expectations Ref.

Observe that the video is displayed accordingly.

Note :

For a 16:9 iDTV or

STB connected to a

16:9 display, it shall follow Figure 5.1b.

For an STB connected to a 4:3 display, it shall follow Figure 5.1a

4:3 Display

Video as in Figure 5.1a shall be presented :

Figure 5.1a

16:9 Display

Video as in Figure 5.1b shall be presented :

Figure 5.1b

3.2.3.5

Result Remarks

71

MCMC MTSFB TC T011:2014

Section 5.1 : AFD

No. Test instructions

5.1.3 Enter service 'AFD

(1011)' by pressing

200.

5.1.4 Enter service 'AFD

(1001)' by pressing

300.

Checkpoints

Observe that the video is displayed accordingly.

Note :

For a 16:9 iDTV or

STB connected to a

16:9 display, it shall follow Figure 5.1d.

For an STB connected to a 4:3 display, it shall follow Figure 5.1c.

Observe that the video is displayed accordingly.

Note :

For a 16:9 iDTV or

STB connected to a

16:9 display, it shall follow Figure 5.1f.

For an STB connected to a 4:3 display, it shall follow Figure 5.1e.

Expectations

Video as in Figure 5.1c shall be presented :

Video as in Figure 5.1d shall be presented :

Figure 5.1c

Video as in Figure 5.1e shall be presented :

Figure 5.1e

Figure 5.1d

Video as in Figure 5.1f shall be presented :

Figure 5.1f

Ref.

3.2.3.5

3.2.3.5

Result Remarks

72

6.4.5.2 Results of AFD Test

Results of AFD Test

Number of Passes

Number of Fails

Number of Not Tested

Total test items

MCMC MTSFB TC T011:2014

73

MCMC MTSFB TC T011:2014

6.4.6 Multiple Physical Layer

This test contains the following sections :

Section 6.1 : Multiple

Physical Layer Pipes

Note :

Reference Document

(Ref.) : SKMM MTSFB

TC T004:2013 -

Specification for Digital

Terrestrial Television

Broadcast Service

Receiver

Test Streams :

MYS_MPLP_HD.ts

MYS_MPLP_SD.ts

MYS_MPLP_Radio.ts

Note :

The Test Streams are available with the

Communication and

Multimedia

Certification Section,

SIRIM QAS

International Sdn Bhd

Stream Configuration :

Playback Settings:

Modulation Type : DVB-T2

Guard Interval : 1/128

Channel Frequency : 474 MHz - 858 MHz

Mode : 32K

Bandwidth : 8 MHz

Modulation : 64 QAM

Recommended PLP Parameters:

Numbers of PLPs

Stream

3

MYS_MPLP_HD.ts MYS_MPLP_SD.ts

PLP ID

Group

0

1

2

256 QAM

4/5

64K

1

1

2

64 QAM

4/5

64K

MYS_MPLP_Radio.ts

2

1

2 PLP Type

Modulation

Code Rate

FEC Type

HEM

1,517.14

674.934

Long

HEM

476.313

674.934

Long

16 QAM

4/5

64K

HEM Baseband Mode

BUFS

Design Delay

ISSY

0

3

1

0

0

3

1

0

476.313

674.934

Long

0 Time Interleaver type

Time Interleaver type

Interleaver frame

1 st

Frame

In band signalling

Constellation Rotation

Disabled

YES

Disabled

YES

3

1

0

Disabled

YES

Number of Blocks 84 28 28

*Note : T2Xpress file configuration setting is provided in the test stream folder as a reference setting

74

MCMC MTSFB TC T011:2014

6.4.6.1 Multiple Physical Layer Pipes

Section 6.1 : Multiple Physical Layer Pipes

No. Test instructions

6.1.1 Ensure L1 Post Scrambling is disabled.

Play out streams

MYS_MPLP_HD.ts,

MYS_MPLP_SD.ts, and

MYS_MPLP_Radio.ts and perform receiver auto scan method.

Expectations

Total of 9 services shall be visible in the service list and shall be in ascending order as below:

LCN 001 MPLP HD Service 1

LCN 002 MPLP HD Service 2

LCN 003 MPLP HD Service 3

LCN 004 MPLP SD Service 1

LCN 005 MPLP SD Service 2

LCN 006 MPLP SD Service 3

LCN 007 MPLP Radio Service 1

LCN 008 MPLP Radio Service 2

LCN 009 MPLP Radio Service 3

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

Enter each service and ensure video and audio components are available.

For Radio service types, only audio components shall be available.

Note: This is a functional test and as such it is acceptable if artefacts are observed when the stream loops around.

Ref.

3.2.10.5

3.2.10.6

Result Remarks

75

MCMC MTSFB TC T011:2014

Section 6.1 : Multiple Physical Layer Pipes

No. Test instructions

6.1.2 Ensure L1 Post Scrambling is enabled.

Play out streams

MYS_MPLP_HD.ts,

MYS_MPLP_SD.ts, and

MYS_MPLP_Radio.ts and perform receiver auto scan method.

Expectations

Total of 9 services shall be visible in the service list and shall be an ascending order as below:

LCN 001 MPLP HD Service 1

LCN 002 MPLP HD Service 2

LCN 003 MPLP HD Service 3

LCN 004 MPLP SD Service 1

LCN 005 MPLP SD Service 2

LCN 006 MPLP SD Service 3

LCN 007 MPLP Radio Service 1

LCN 008 MPLP Radio Service 2

LCN 009 MPLP Radio Service 3

Confirm that receiver shall be able to access to each service normally via numerical keys and service list.

Enter each service and ensure video and audio components are available.

For Radio service types, only audio components shall be available.

Note : This is a functional test and as such it is acceptable if artefacts are observed when the stream loops around

Ref.

3.2.10.5

3.2.10.6

Result Remarks

76

6.4.6.2 Results of Multiple-PLP Test

Results of Multiple-PLP Test

Number of Passes

Number of Fails

Number of Not Tested

Total test items

6.4.7 Self Declaration

This section is to declare that this receiver confirms to the Malaysia Specification for the following.

No Section Section name

7.1

7.2

7.3

7.4

3.2.4

3.2.5

3.2.15

3.2.16

Decoding of Audio

Display of Subtitles

Outputs

Remote Control

7.5 3.2.17

6.4.7.1 Results of Declaration

Maintenance & Upgrade: Summary

Results of Declaration

Number of Passes

Number of Fails

Number of Not Tested

Total test items

77

MCMC MTSFB TC T011:2014

Result

MCMC MTSFB TC T011:2014

6.4.7.2 Notes - T2Xpress Settings

Number of PLPs

Stream

PLP ID

Group

PLP Type

Modulation

Code Rate

FEC Type

Baseband Mode

BUFS

Design Delay

ISSY

Time interleaver type

Time interleaver length

Interleaver frame

1st Frame

In band signalling

Constellation Rotation

Number of Blocks

MYS_MPLP_HD.ts

0

1

2

256 QAM

4/5

64K

HEM

1,517.14

674.934

Long

0

3

1

0

Disabled

YES

84

78

3

MYS_MPLP_SD.ts

1

1

2

64 QAM

4/5

64K

HEM

476.313

674.934

Long

1

0

0

3

Disabled

YES

28

MYS_MPLP_Radio.ts

2

1

2

16 QAM

4/5

64K

HEM

476.313

674.934

Long

0

3

1

0

Disabled

YES

28

MCMC MTSFB TC T011:2014

7. Malaysia (MYS) SI/PSI Test Requirement

This document contains the general Test Requirements derived from the Malaysian Specification and covers all the mandatory test items that are required in the test suite. This document is categorized into multiple sections covering test elements which are mandated in the Specification.

7.1 Frequency Range

Sec Category Purpose and Outcome Ref Classification

1 Frequency Range

3.2.10.4 Mandatory 1.1 Channel

Bandwidth

1.2 Operating

Modes

Purpose :

To ensure the channels are captured within the frequency range specified in the

Malaysia Specification, as defined below:

Bandwidth : 7 MHz

VHF III : 174 - 230 MHz

Bandwidth : 8 MHz

UHF IV & V : 470 - 860 MHz

Outcome :

When tuning is performed, receiver shall be able to capture all the services correctly with the above configuration.

Purpose:

To ensure the operating modes in the

Malaysia Specification are fulfilled. (These include MPLP and L1 Post Scrambling functionalities.)

Outcome :

When tuning is performed, receiver shall be able to capture all the services signalled with the parameters set as in the Malaysia

Specification.

7.2 Service Installation

Sec Category Purpose and Outcome

2 Service Installation

2.1 Automatic

Tuning

Purpose:

To ensure receiver is able to perform automatic tuning and installed all the services.

Outcome:

Captured services are successfully presented in the service list.

3.2.10.5

3.2.10.6

Ref

3.2.11.1

Mandatory

Classification

Mandatory

79

MCMC MTSFB TC T011:2014

7.3 Video Decoding

Sec Category Purpose and Outcome

3 Video Decoding

3.1 Video

Resolution, Video

Purpose:

To ensure that the receiver shall support and

Aspect ratio and

Profile display video resolution, aspect ratio and profile as below: i. 1080i/25Hz; 16:9 ; AVC HP@L4 ii. 720p/50Hz; 16:9 ; AVC HP@L4 iii. 576i/25Hz; 4:3 & 16:9 ; AVC MP@L3

Outcome:

The receiver shall correctly present the video component in the supported resolutions as specified above.

3.2 Active Format

Description (AFD)

Purpose:

To ensure Active Format Description (AFD) is supported as mentioned in the Malaysia

Specification.

General Outcome:

Receiver shall be able to process the AFD information and display the correct AFD.

7.4 Audio Decoding

Sec Category Purpose and Outcome

4 Audio Decoding

4.1 Audio

Formats

Purpose:

To ensure that the receivers are able to support the following audio requirements as defined in the Malaysia Specification: i. MPEG-4 HE-AAC v2L2 (Stereo) ii. MPEG-4 HE-AAC multi-channel

Outcome:

The audio formats as defined above shall be decoded correctly by the receiver.

Ref

3.2.3

3.2.3.1

3.2.3.2

3.2.3.5

Ref

3.2.4

3.2.4.1

Classification

Mandatory

Mandatory

Classification

Mandatory

80

MCMC MTSFB TC T011:2014

7.5 Subtitling

Sec Category Purpose and Outcome

5 Subtitling

5.1 Subtitle

Support

Purpose:

To ensure the receiver is able to decode

DVB subtitles according to the Malaysia

Specification.

Outcome:

The receiver shall be able to display the subtitles correctly as signalled in the stream.

7.6 Time and Data Information

Sec Category Purpose and Outcome

6 Time and Data Information

6.1 Time and

Date Information

Purpose :

To ensure receiver shall display the time and date information carried in the relevant SI tables.

Outcome :

The receiver shall be able to display the information on the screen correctly.

7.7 EIT Presentation

Sec Category Purpose and Outcome

7 EIT Presentation

7.1 Event

Information

(Present and

Following)

7.2 Event

Schedule

Purpose:

To ensure that the receiver is able to present the event Information based on the EIT p/f tables as mentioned in the Malaysia

Specification.

Outcome:

The receiver shall display the content of the event Information correctly in the ‘Now/Next’ screen guide.

Purpose :

To ensure the receiver is able to display 7 days of EPG information

Outcome:

The event schedule presented for 7 days contains complete information.

Ref

3.2.5

Ref

3.2.13

Ref

3.2.12

3.2.12.1

3.2.12.2

Classification

Mandatory

Classification

Mandatory

Classification

Mandatory

Mandatory

81

MCMC MTSFB TC T011:2014

Sec Category Purpose and Outcome

7 EIT Presentation

7.3 Character

Transmission

Purpose :

To ensure the receiver is able to support the

Character Sets specified in Malaysia

Specification.

Outcome :

The receiver is able to display the correct characters signalled in the PSI tables which are related to the character transmission.

7.8 Audio and Subtitle Language Support

Sec Category Purpose and Outcome

8 Audio and Subtitle Language Support

8.1 Multiple

Subtitle Language

Support

Purpose:

To ensure the receiver is able to support multiple subtitles within the same service.

Outcome:

The receiver shall be able to present the correct subtitle languages according to user settings.

8.2 Multiple Audio

Language

Support

Purpose :

To ensure the receiver is able to support multiple audio languages within the same service.

Outcome :

The receiver shall be able to present the correct audio languages according to user settings.

7.9 Logical Channel Numbering

Sec Category Purpose and Outcome

9 Logical Channel Numbering

9.1 LCN Version

1

Purpose:

To ensure receivers are able to process the

LCN Version 1 descriptor.

Outcome:

The receiver shall be able to solve duplicate and conflicted LCN conditions and access hidden services via numerical keys with the usage of the LCN Version 1 descriptor.

Ref

3.2.8

Ref

3.2.6

3.2.6

Ref

3.2.11.2

3.2.11.4

3.2.19

Classification

Mandatory

Classification

Mandatory

Mandatory

Classification

Mandatory

82

MCMC MTSFB TC T011:2014

Sec Category

9 Logical Channel Numbering

Purpose and Outcome

9.2 LCN Version

2

9.3 Regional

Broadcast

Management

Purpose:

To ensure receivers are able to process the

LCN Version 2 descriptor.

Outcome:

The receiver shall be able to solve duplicate and conflicted LCN conditions, access hidden services via numerical keys, and select preferred channel list with the usage of the LCN Version 2 descriptor.

Purpose:

To ensure receivers are able to collate all channel lists and the services are presented based on preferred channel list.

Outcome:

Services with correct logical channel number are presented.

7.10 Network Evolution

Sec Category Purpose and Outcome

10 Network Evolution

10.1 Service

Addition/

Deletion

10.2 Multiplex

Reconfiguration

Purpose:

To ensure receiver is able to perform service addition and deletion when network scan is performed.

Outcome:

The added services shall be presented in the service list. The deleted services shall not be available to user.

Purpose:

To ensure the receiver shall automatically detect configuration changes to the network, such as addition of new multiplexes.

Outcome:

Services from newly added multiplex shall populate the service list after network scanning.

10.3 Clash

Resolution

Purpose:

To ensure the receiver is able to behave according to the Malaysian Specification in the case of clash resolution.

Outcome:

The receiver shall give precedence to the service belonging to the multiplex with the best RF when as LCN Conflict is detected.

Ref

3.2.11.3

3.2.11.4

3.2.19

3.2.11.5

3.2.19

Ref

3.2.11.6

3.2.11.6

3.2.11.6

Classification

Mandatory

Mandatory

Classification

Mandatory

Mandatory

Mandatory

83

MCMC MTSFB TC T011:2014

Sec Category Purpose and Outcome

10 Network Evolution

10.4 Event p/f

Transitions

Purpose :

To ensure receiver is able to perform event p/f transitions with version updates.

Outcome :

Receiver shall display the event p/f information according to the version updates.

7.11 Time Exclusive Services

Sec Category Purpose and Outcome

11 Time Exclusive Services

11.1 Transition between active and inactive state

Purpose:

To ensure the receiver is able to handle transition between the active and inactive states of time exclusive service orderly.

Outcome:

Receiver shall present clean transition into and out of the service presentation.

Ref Classification

3.2.12.1 Mandatory

Ref

3.2.2.1

Classification

Mandatory

84

MCMC MTSFB TC T011:2014

8. Malaysia DVB-T2 Over Air Download (OAD) Test Suite Ver1.0

8.1 Revision history

No Date Description

1

8.2 Evaluation details

2014-06-03

Receiver Under Test (RUT)

First official release

RUT Device Type (iDTV/Set top box)

RUT Firmware Version

8.3 Evaluation Results

No. Test Descriptions

1. Stream with SSU matches target receiver (Valid OUI) and model tested.

Note: Higher package version

2. Stream with SSU does not match target receiver (Invalid OUI).

3. Stream with SSU matches target receiver (Valid OUI) and but with different model tested.

Note: Higher package version

4. Stream with SSU matches target receiver (Valid OUI) and model tested.

Note: Same package version

5. Interruption while OAD downloading/updating

OVERALL RESULTS

Version v1.0

Result

Remark

Remarks

85

MCMC MTSFB TC T011:2014

8.4 Test Description

Test

ID

Test Description

1 Stream with SSU matches target receiver

(Valid OUI) and model tested.

Note: Higher package

version

2 Stream with SSU does not match target receiver (Invalid OUI).

3 Stream with SSU matches target receiver

(Valid OUI) and but with different model tested.

Note: Higher package

version

Test

Environment

(TS name, etc.)

Modulate TS1

(any frequency is ok, i.e.

650MHz)

Modulate TS2

(any frequency is ok, i.e.

650MHz)

Modulate TS3

(any frequency is ok, i.e.

650MHz)

Test Procedure

1. Check the receiver base software version in the menu system and place receiver to the shipping condition (e.g. Factory Reset).

2. Play stream and perform installation.

3. Perform receiver mechanism to initiate OAD download (e.g. Put receiver into standby).

Note: The OAD download shall not be initiated from the system menu.

1. Check the receiver base software version in the menu system and place receiver to the shipping condition (e.g. Factory Reset).

2. Play stream and perform installation.

3. Perform receiver mechanism to initiate OAD download (e.g. Put receiver into standby).

Note: The OAD download shall not be initiated from the system menu.

1. Check the receiver base software version in the menu system and place receiver to the shipping condition (e.g. Factory Reset).

2. Play stream and perform installation.

3. Perform receiver mechanism to initiate OAD download (e.g. Put receiver into standby).

Note: The OAD download shall not be initiated

from the system menu.

Expected Behaviour

Receiver shall be capable to download OAD data completely and update the new software version correctly.

Receiver shall not detect any OAD data and prompt any software update notification

Software version in receiver system menu shall remain the same.

Receiver shall not detect any OAD data and prompt any software update notification.

Software version in receiver system menu shall remain the same.

Result Remarks

86

MCMC MTSFB TC T011:2014

Test

ID

Test Description

4 Stream with SSU matches target receiver

(Valid OUI) and model tested.

Note:

Same package version

5 Interruption while OAD downloading/updating i.e. unplug power cord

Note:

Stream with SSU matches target receiver

(Valid OUI) and model with higher package

version tested.

Test

Environment

(TS name, etc.)

Modulate

(any frequency is ok,

650MHz)

TS4 i.e.

Modulate TS1

(any frequency is ok, i.e.

650MHz)

Test Procedure

1. Check the receiver base software version in the menu system and place receiver to the shipping condition (e.g. Factory Reset).

2. Play stream and perform installation.

3. Perform receiver mechanism to initiate OAD download (e.g. Put receiver into standby).

1. Check the receiver base software version in the menu system and place receiver to the shipping condition (e.g. Factory Reset).

2. Play stream and perform installation.

3. Perform receiver mechanism to initiate OAD download (e.g. Put receiver into standby).

4. While receiver is downloading the OAD, unplug the power cord of the receiver.

5. Then, plug in the power cord again and confirm the receiver is operational.

6. Perform receiver mechanism to initiate OAD download (e.g. put receiver into standby).

Note: The OAD download shall not be initiated from the system menu.

8.5 Results of OAD Test

Results of OAD Test:

Expected Behaviour

Receiver shall not detect any OAD data and prompt any software update notification.

Software version in receiver system menu shall remain the same.

Receiver shall restart

OAD downloading until completion and update the new software version correctly.

Result

Number of Passes

Number of Fails

Number of Not Tested

Total test items

Remarks

87

MCMC MTSFB TC T011:2014

8.6 Test Environment

No Name TS Description

1

3

4

TS1

TS3

TS4

1. TS1 contains valid target receiver OUI in PMT and the OAD data for the target receiver in DSM-CC.

2. OAD data includes higher package version than the base version.

1. TS3 contains invalid OUI, which does not match the target receiver and model type.

2. OAD data includes higher package version than the base version.

1. TS4 contains valid OUI, which matches the target receiver but does not match the model type.

2. OAD data includes higher package version than the base version.

5 TS4 1. TS5 includes valid OUI which matches the target receiver and model type.

2. OAD data includes same package version than the base version.

Note: It is the responsibility of each manufacturer to create their own transport streams.

88

MCMC MTSFB TC T011:2014

8.7 Transport Stream Structure

8.7.1 Transport Stream (option 1)

PMT

Service ID: yyyy

DSM-CC Type B (Type: 0 x 0b)

PID: zzzz

Data Broadcast ID: 0 x 000a (SSU)

OUI: 0 x 00015a (Digital Video Broadcasting (DVB))

Update type: 0 x1 (Standard Update

Carousel via Broadcast)

DSM-CC

PID: zzzz

Download Info Indication (DII)

Download Data Block (DDB)

Download Server Initiate (DSI)

Compatibility Descriptor

System hardware

Specifier Type: 0 x 01 (IEEE OUI)

OUI: xxxxxxxx (Registered Receiver)

Model: xxxxxxxx

Version: xxxxxxxx

System Software

Specifier Type: 0 x 01 (IEEE OUI)

OUI: xxxxxxxx (Registered Receiver)

Model: xxxxxxxx

Version: xxxxxxxx

Sub-Descriptor (Note: Optional and

for private use)

INT

Network ID: xxxxxx

Network Name: xxxxxxx

Linkage Descriptor

Transport Stream ID: xxxxxx

Original Network Stream ID: xxxxxx

Service ID: xxxxxx

Linkage Type: 0 x 09 (SSU)

OUI: 0 x 00015a (Digital Video Broadcasting

(DVB))

89

MCMC MTSFB TC T011:2014

8.7.2 Transport Stream (option 2)

PMT

Service ID: yyyy

DSM-CC Type B (Type: 0 x 0b)

PID: zzzz

Data Broadcast ID: 0 x 000a (SSU)

OUI: xxxxxxxx (Registered Receiver)

Update type: 0 x 1 (Standard Update

Carousel via Broadcast)

DSM-CC

PID: zzzz

Download Info Indication (DII)

Download Data Block (DDB)

Download Server Initiate (DSI)

Compatibility Descriptor

System hardware

Specifier Type: 0 x 01 (IEEE OUI)

OUI: xxxxxxxx (Registered Receiver)

Model: xxxxxxxx

Version: xxxxxxxx

System Software

Specifier Type: 0 x 01 (IEEE OUI)

OUI: xxxxxxxx (Registered Receiver)

Model: xxxxxxxx

Version: xxxxxxxx

Sub-Descriptor (Note: Optional and

for private use)

INT

Network ID: xxxxxx

Network Name: xxxxxxx

Linkage Descriptor

Transport Stream ID: xxxxxx

Original Network Stream ID: xxxxxx

Service ID: xxxxxx

Linkage Type: 0 x 09 (SSU)

OUI: xxxxxxxx (Registered Receiver)

90

MCMC MTSFB TC T011:2014

9. Malaysia Hybrid Broadcast TV (HBBTV) Test Suite Ver1.0

9.1 Revision history

No Date Description Version v1.0 1 2014-06-03

9.2 Evaluation details

First official release

Receiver Under Test (RUT)

RUT Device Type (iDTV/Set top box)

RUT Firmware Version

9.3 Evaluation results

No Test Suite Test Case Passed Failed Not Tested

1.0 HbbTV 0.9

2.0 DASH

3.0 Recording

4.0 Marlin DRM

5.0 EIT

6.0

9.4 Test Suite

9.4.1 HbbTV 0.9

No Test Case

1

2

3

4

5

6

7

8

References

Title

00000020 Test for running PRESENT application after service selection (Service Bound)

00000030 Test for running AUTOSTART application after service selection (Not Service Bound)

00000040 Test for running PRESENT application after service selection (Not Service Bound)

00000050 Test for running DISABLED application after service selection (Not Service Bound)

00000060 Test for KILLED application after service selection (Not

Service Bound)

00000070 Test for NOT SIGNALLED application after service selection (Not Service Bound)

00000110 AIT changes while no broadcast related application is running, AUTOSTART application from DSMCC signalled, part 1

00000130 Service selection with AUTOSTART application from broadband, part 1 (success)

Remark

Result

Remark

Remark

91

MCMC MTSFB TC T011:2014

No

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

Test Case Title

00000160 AIT changes while no broadcast related application is running, multiple AUTOSTART applications signalled, broadband and broadcast, part 1

00000170 AIT changes while no broadcast related application is running, multiple AUTOSTART applications signalled, broadband and broadcast, part 2

00000190 AIT changes while no broadcast related application is running, multiple AUTOSTART applications signalled, broadband, part 1

00000200 AIT changes while no broadcast related application is running, multiple AUTOSTART applications, broadband signalled, part 2

00000210 AIT changes while no broadcast related application is running, AUTOSTART application signalled on broadband and broadcast, part 1

00000220 AIT changes while no broadcast related application is running, AUTOSTART application signalled on broadband and broadcast, part 2

00000240 AIT changes while no broadcast related application is running, AUTOSTART application signalled on broadcast

(higher priority) and broadband, part 1

00000250 AIT changes while no broadcast related application is running, AUTOSTART application signalled on broadcast

(higher prio) and broadband, part 2 (failure)

00000260 AIT update with no AUTOSTART applications, broadband and broadcast, part 3

00000270 AIT changes while broadcast related application is running, application still signalled

00000280 AIT changes while broadcast related application is running, application signalled with KILL

00000290 AIT changes while broadcast related application is running, application not signalled

00000300 AIT changes while no broadcast related application is running, AUTOSTART application from HTTP signalled

00000310 Application exits

00000320 Triggering Channel Change Succeeded Event when transitioning from Broadcast Related to Broadcast

Independent state

00000330 Broadcast Independent Applications created from an

HTML page accessed over HTTP

00000340 A broadcast-independent application transitioning to a broadcast-related application shall not be killed if all specified conditions are met

00000350 A broadcast-independent application transitioning to a broadcast-related application shall be killed if the first of the specified conditions are not met

Result Remark

92

MCMC MTSFB TC T011:2014

31

32

51

52

53

54

47

48

49

50

55

56

57

42

43

44

45

46

34

35

36

37

38

39

40

41

No

27

28

29

30

33

Test Case Title

00000360 A broadcast-independent application transitioning to a broadcast-related application shall be killed if the second of the specified conditions are not met

00000370 A broadcast-independent application transitioning to a broadcast-related application shall be killed if the third of the specified conditions are not met

00000380 A broadcast-independent application transitioning to a broadcast-related application shall be killed if the fourth of the specified conditions are not met

00000400 Broadcast Independent Applications created from an

XML AIT over HTTP and with no boundary defined

00000440 Broadcast Independent Applications started from a

Broadcast Related application

00000450 Transition of an Application from Broadcast Related to

Broadcast Independent state using Set Channel

00000460 A broadcast-independent application transitioning to a broadcast-related application shall be killed if the fifth of the specified conditions are not met

00000570 User input - VK_BACK

00000580 User input - VK_0

00000590 User input - VK_1

00000600 User input - VK_2

00000610 User input - VK_3

00000620 User input - VK_4

00000630 User input - VK_REWIND

00000640 User input - VK_RED

00000650 User input - VK_GREEN

00000660 User input - VK_YELLOW

00000670 User input - VK_BLUE

00000680 User input - VK_UP

00000690 User input - VK_DOWN

00000700 User input - VK_LEFT

00000710 User input - VK_RIGHT

00000720 User input - VK_ENTER

00000730 User input - VK_5

00000740 User input - VK_6

00000750 User input - VK_7

00000760 User input - VK_8

00000770 User input - VK_9

00000780 User input - VK_STOP

00000790 User input - VK_PLAY

00000800 User input - VK_PAUSE

Result Remark

93

MCMC MTSFB TC T011:2014

63

64

65

66

67

68

69

70

71

72

75

76

77

No

58

59

60

61

62

73

74

78

79

80

81

82

83

Test Case Title

00000810 User input - VK_PLAY_PAUSE

00000820 User input - VK_FAST_FWD

00000830 User input - CSS3 directional focus navigation - VK_UP

00000840 User input - CSS3 directional focus navigation -

VK_DOWN

00000850 User input - CSS3 directional focus navigation -

VK_LEFT

00000860 User input - CSS3 directional focus navigation -

VK_RIGHT

00000910 User input - Javascript navigation - VK_UP

00000920 User input - Javascript navigation - VK_DOWN

00000930 User input - Javascript navigation - VK_LEFT

00000940 User input - Javascript navigation - VK_RIGHT

00000950 User input - Navigation priority - VK_RIGHT

00000960 User input - Navigation priority - VK_UP

00000970 User input - Navigation priority - VK_DOWN

00000980 User input - Navigation priority - VK_LEFT

00000990 Access to resources inside the boundary of an application loaded from carousel

00001000 Loading a document outside the boundary of an application loaded via HTTP

00001010 Loading a document from outside the application boundary including a document from within the application domain

00001020 Access to resources within the Application domain via

XMLHttpRequest

00001030 Access to resources outside the application domain via

XmlHttpRequest

00001040 Access to "trusted" API from within an iframe loaded from inside the application domain

00001050 Block access to trusted API from document outside the application domain

00001060 Access to trusted APIs from a document inside the application boundary of a trusted application loaded via

HTTP

00001150 Access to trusted API from a document outside the application domain (app loaded via HTTP)

00001160 Access to trusted API from a document outside the application domain (app loaded via carousel)

00001170 Access to trusted API from a document inside the application domain (app loaded via carousel)

00001180 Access to carousel via XMLHttpRequest (app loaded via carousel)

Result Remark

94

MCMC MTSFB TC T011:2014

No Test Case Title

84

85

86

87

88

89

90

91

92

93

94

00001190 Access to resources outside the application domain via

XMLHttpRequest

00001200 Access to trusted API from a document inside the application domain (app loaded via carousel)

00001210 Blocking access to trusted API from a document outside the application domain (app loaded via carousel)

00001410 Status value is 404 when trying to access non-existing

DSM-CC objects with XMLHttpRequest

00001420 When accessing DSM-CC objects with XMLHttpRequest, statusText will return an empty string

00001450 Calls to getAllResponseHeaders() return an empty string when accessing DSM-CC objects with XMLHttpRequest

00001460 When accessing a DSM-CC File object with

XMLHttpRequest, responseText returns the content of the requested file

00001470 When accessing a DSM-CC Directory object with

XMLHttpRequest, responseText returns a commaseparated list of objects in the directory

00001480 When accessing a DSM-CC File object with ".xml" extension with XMLHttpRequest, responseXML returns an XML document object

00001490 When accessing a DSM-CC Directory object with

XMLHttpRequest, responseXML returns null

00001500 When accessing a DSM-CC Stream Event object with

XMLHttpRequest, responseXML returns null

95

96

97

00001520 Test of minimum terminal capabilities. Supported proportional font

00001530 Test of minimum terminal capabilities. Supported proportional font

00001540 Test of minimum terminal capabilities. Supported proportional font

98

99

00001550 Test of minimum terminal capabilities. Supported proportional font

00001560 Test of minimum terminal capabilities. Supported nonproportional font

100 00001570 Test of minimum terminal capabilities. Supported nonproportional font

101 00001580 Test of minimum terminal capabilities. Supported nonproportional font

102 00001680 State of a video/broadcast object when it is instantiated

103 00001710 Change of state of a video/broadcast object when the bindToCurrentChannel() method is called while it is in the unrealized state

104 00001720 Change of state of a video/broadcast object when the release() method is called while it is in the unrealized state

Result Remark

95

MCMC MTSFB TC T011:2014

No Test Case Title

105 00001730 Change of state of a video/broadcast object when the stop() method is called while it is in the unrealized state

106 00001810 Change of state of a video/broadcast object when the nextChannel() method is called while it is in the presenting state

107 00001820 Change of state of a video/broadcast object when the prevChannel() method is called while it is in the presenting state

108 00001830 Change of state of a video/broadcast object when the bindToCurrentChannel() method is called while it is in the presenting state

109 00001840 Change of state of a video/broadcast object when the release() method is called while it is in the presenting state

110 00001850 Change of state of a video/broadcast object when the stop() method is called while it is in the presenting state

111 00001900 Change of state of a video/broadcast object when the bindToCurrentChannel() method is called while it is in the stopped state

112 00001910 Change of state of a video/broadcast object when the release() method is called while it is in the stopped state

113 00001920 Change of state of a video/broadcast object when the stop() method is called while it is in the stopped state

114 00001940 video/broadcast object presentation - presenting state

115 00001950 video/broadcast object presentation - stopped state

116 00001970 Change of state of a video/broadcast object when the setChannel() method is called (with a null parameter) while it is in the unrealized state

117 00002000 Change of state of a video/broadcast object when the setChannel() method is called (with a correct parameter) while it is in the presenting state

118 00002010 Change of state of a video/broadcast object when the setChannel() method is called (with a null parameter) while it is in the presenting state

119 00002020 Change of state of a video/broadcast object when the setChannel() method is called (with a correct parameter) while it is in the stopped state

120 00002030 Change of state of a video/broadcast object when the setChannel() method is called (with a null parameter) while it is in the stopped state

121 00002230 AV Object Overlap (Partial overlap of object with a higher

Z index)

122 00002240 AV Object Overlap (Partial overlap of object with a lower

Z index)

123 00002250 AV Object Overlap (Total overlap of object with a higher

Z index)

Result Remark

96

MCMC MTSFB TC T011:2014

No Test Case Title

124 00002260 AV Object Overlap (Total overlap of object with a lower Z index)

125 00002270 AV Object Scaling (1/8; Video Res 1280x720; 16:9)

126 00002280 AV Object Scaling (1/8; Video Res 640x720; 16:9)

127 00002290 AV Object Scaling (1/8; Video Res 720x576; 16:9)

128 00002300 AV Object Scaling (1/8; Video Res 352x288; 4:3)

129 00002310 AV Object Scaling (2/13; Video Res 1280x720; 16:9)

130 00002320 AV Object Scaling (2/13; Video Res 640x720; 16:9)

131 00002330 AV Object Scaling (2/13; Video Res 720x576; 16:9)

132 00002340 AV Object Scaling (2/13; Video Res 352x288; 4:3)

133 00002350 AV Object Scaling (x2; Video Res 1280x720)

134 00002360 AV Object Scaling (x2; Video Res 640x720)

135 00002370 AV Object Scaling (x2; Video Res 720x576)

136 00002380 AV Object Scaling (x2; Video Res 352x288)

137 00002390 AV Object Scaling (1/2x1/4; Video Res 1280x720)

138 00002400 AV Object Scaling (1/2x1/4; Video Res 640x720)

139 00002410 AV Object Scaling (1/2x1/4; Video Res 720x576)

140 00002420 AV Object Scaling (1/2x1/4; Video Res 352x288)

141 00002430 Terminal stores cookies with an expiry date in persistent memory

142 00002440 Cookies expire at the correct time

143 00002510 Test of support for MP4 File Format streamed over

HTTP; 1280x720p@25, 16:9

144 00002520 Test of support for MP4 File Format streamed over

HTTP; 352x288i@25, 4:3

145 00002530 Test of support for MPEG-2 TS streamed over HTTP;

1280x720p@25, 16:9

146 00002540 Test of support for MPEG-2 TS streamed over HTTP;

352x288i@25, 4:3

147 00002590 Test of High Bitrate Streaming; MP4 File Format

148 00002610 Test that terminal ignores any AIT signalling present in

MPEG-2 TS streamed over HTTP

149 00002630 Test of support for AVC_SD_25; 720x576p@25, 16:9

150 00002640 Test of support for AVC_SD_25; 544x576p@25, 16:9

151 00002650 Test of support for AVC_SD_25; 480x576p@25, 16:9

152 00002660 Test of support for AVC_SD_25; 352x576p@25, 16:9

153 00002670 Test of support for AVC_SD_25; 352x288p@25, 16:9

154 00002680 Test of support for AVC_SD_25; 720x576i@25, 16:9

155 00002690 Test of support for AVC_SD_25; 544x576i@25, 16:9

156 00002700 Test of support for AVC_SD_25; 480x576i@25, 16:9

157 00002710 Test of support for AVC_SD_25; 352x576i@25, 16:9

Result Remark

97

MCMC MTSFB TC T011:2014

No Test Case Title

158 00002720 Test of support for AVC_SD_25; 352x288i@25, 16:9

159 00002730 Test of support for AVC_SD_25; 720x576p@25, 4:3

160 00002740 Test of support for AVC_SD_25; 544x576p@25, 4:3

161 00002750 Test of support for AVC_SD_25; 480x576p@25, 4:3

162 00002760 Test of support for AVC_SD_25; 352x576p@25, 4:3

163 00002770 Test of support for AVC_SD_25; 352x288p@25, 4:3

164 00002780 Test of support for AVC_SD_25; 720x576i@25, 4:3

165 00002790 Test of support for AVC_SD_25; 544x576i@25, 4:3

166 00002800 Test of support for AVC_SD_25; 480x576i@25, 4:3

167 00002810 Test of support for AVC_SD_25; 352x576i@25, 4:3

168 00002820 Test of support for AVC_SD_25; 352x288i@25, 4:3

169 00002830 Test of support for AVC_HD_25; 1280x720p@25, 16:9

170 00002840 Test of support for AVC_HD_25; 960x720p@25, 16:9

171 00002850 Test of support for AVC_HD_25; 640x720p@25, 16:9

172 00002860 Test of support for AVC_HD_25; 1280x720i@25, 16:9

173 00002870 Test of support for AVC_HD_25; 960x720i@25, 16:9

174 00002880 Test of support for AVC_HD_25; 640x720i@25, 16:9

175 00002890 Test of support for AVC_HD_25; 1920x1080p@25, 16:9

176 00002900 Test of support for AVC_HD_25; 1440x1080p@25, 16:9

177 00002910 Test of support for AVC_HD_25; 1280x1080p@25, 16:9

178 00002920 Test of support for AVC_HD_25; 960x1080p@25, 16:9

179 00002930 Test of support for AVC_HD_25; 1920x1080i@25, 16:9

180 00002940 Test of support for AVC_HD_25; 1440x1080i@25, 16:9

181 00002950 Test of support for AVC_HD_25; 1280x1080i@25, 16:9

182 00002960 Test of support for AVC_HD_25; 960x1080i@25, 16:9

183 00002970 Test of support for AVC_HD_25; 1280x720p@50, 16:9

184 00002980 Test of support for AVC_HD_25; 960x720p@50, 16:9

185 00002990 Test of support for AVC_HD_25; 640x720p@50, 16:9

186 00003000 Test of support for HE-AAC; Mono, AV Content,

Streamed over HTTP

187 00003010 Test of support for HE-AAC; Stereo, AV Content,

Streamed over HTTP

188 00003020 Test of support for HE-AAC; Multichannel, AV Content,

Streamed over HTTP

189 00003030 Test of support for AAC; Mono, AV Content, Streamed over HTTP

190 00003040 Test of support for AAC; Stereo, AV Content, Streamed over HTTP

191 00003050 Test of support for AAC; Multichannel, AV Content,

Streamed over HTTP

Result Remark

98

MCMC MTSFB TC T011:2014

No Test Case Title

192 00003060 Test of support for AC-3; Mono, AV Content, Streamed over HTTP

193 00003070 Test of support for AC-3; Stereo, AV Content, Streamed over HTTP

194 00003080 Test of support for AC-3; Multichannel, AV Content,

Streamed over HTTP

195 00003120 Test of support for HE-AAC; Mono, Audio Only (Radio)

Content, Streamed over HTTP

196 00003130 Test of support for HE-AAC; Stereo, Audio Only (Radio)

Content, Streamed over HTTP

197 00003140 Test of support for HE-AAC; Multichannel, Audio Only

(Radio) Content, Streamed over HTTP

198 00003180 Test of support for MP3; Mono, Audio Only (Radio)

Content, Streamed over HTTP

199 00003190 Test of support for MP3; Stereo, Audio Only (Radio)

Content, Streamed over HTTP

200 00003400 Test of downmixing Multichannel HE-AAC (AV Content)

Streamed over HTTP

201 00003410 Test of downmixing Multichannel AAC (AV Content)

Streamed over HTTP

202 00003420 Test of downmixing Multichannel AC-3 (AV Content)

Streamed over HTTP

203 00003460 Test of interpretation of audio metadata when downmixing Multichannel AC-3 (AV Content) Streamed over HTTP

204 00003540 AV Object Seeking Within Buffer (MP4 Forward 5s)

205 00003560 AV Object Seeking Outside Buffer (MP4 Forward)

206 00003580 AV Object Seeking Outside Buffer (MP4 Backward)

207 00003600 AV Object Seeking Within Buffer (MP4 Backward 5s)

208 00003630 AV Streaming Tests: AV Object (Pause)

209 00003640 AV Streaming Tests: AV Object (Stop)

210 00003650 Test for onPlayStateChanged event when transitioning from Play to Pause

211 00003660 Test for onPlayStateChanged event when transitioning from Play to Stop

212 00003670 Test for onPlayStateChanged event when transitioning from Paused to Playing

213 00003680 Test for onPlayStateChanged event when transitioning from Paused to Stop

214 00003690 Test for onPlayStateChanged event when transitioning from Stop to Play

215 00003700 Test for onPlayStateChanged event when transitioning from Stopped to Pause

216 00003710 the application.privateData.currentChannel after application start

Result Remark

99

MCMC MTSFB TC T011:2014

No Test Case Title

217 00003730 the application.privateData.currentChannel after channel selection by application

218 00003740 CreateApplication with parameters in URL

219 00003750 CreateApplication with hash in URL

220 00003760 video.currentChannel after channel selection by application

221 00003780 video.currentChannel after application start

222 00003790 EIT p/f

223 00003800 Letter Gothic font rendering width

224 00003810 Line-height CSS style

225 00003820 Tiresias font rendering width

226 00003830 OIPF capabilities: hasCapability()

227 00003840 OIPF Capabilities: extra decodes

228 00003850 OIPF Configuration: preferredAudioLanguage

229 00003860 OIPF Configuration: preferredSubtitleLanguage

230 00003870 OIPF Configuration: countryId

231 00003880 StreamEvent reference DVB URL

232 00003890 StreamEvent reference event description file

233 00003920 Invalid video playback: A/V format

234 00003930 Invalid video playback: cannot connect

235 00003940 Invalid video playback: video not found

236 00003950 Playback of video without content-range support

237 00003960 Video playtime

238 00003970 Video queue

239 00003980 Seek in broadband video playback

240 00003990 Video/mp4 keeps aspect ratio

241 00004000 Video/broadcast keeps aspect ratio

9.4.1.1 Results

Results

Passed

Failed

Not Tested

Total test items

9.4.2 Dynamic Adaptive Streaming over HTTP (DASH)

No Test Case Title

1 org.hbbtv_DA540290 Simple DASH A/V stream

Result

Result Remark

Remark

100

MCMC MTSFB TC T011:2014

No Test Case

2 org.hbbtv_DA540310

Title

DASH A/V stream with two video representations

3 org.hbbtv_DA541210

Support for stopping DASH encoded clear content streamed over HTTP

9.4.2.1 Results

Results

Passed

Failed

Not Tested

Total test items

9.4.3 Recording

No Test Case

1

2

3 fr.hdforum_93463000 fr.hdforum_93463010 fr.hdforum_93463020

Title

Recording of broadband MP4 content not permitted

Recording of broadband MP2 TS content not permitted

Recording of broadband MP4 DASH content not permitted

9.4.3.1 Results

Results

Passed

Failed fr.hdforum_93440146

Not Tested fr.hdforum_93440002

Total test items

9.4.4 Marlin Digital Rights Management (DRM)

No Test Case Title

1

2 fr.hdforum_93440102

Verify signalling of Marlin DRM capability to HbbTV application

Support of live encrypted streaming with key rotation and static MPD for Marlin

Terminals

3 Support for normal playback of DASH encoded protected content streamed over HTTP - Marlin Terminals

Result

Result

Result

Remark

Remark

Remark

101

MCMC MTSFB TC T011:2014

9.4.4.1 Results

Results

Passed

Failed

Not Tested

Total test items

9.4.5 Event Information Table (EIT)

No Test Case

1

2 org.hbbtv_E1210020 org.hbbtv_E1210030

Title

EIT P/F - video/broadcast object can decode all required UTF-8 characters

EIT Schedule - MetadataSearch object can decode all required UTF-8 characters

9.4.5.1 Results

Results

Passed

Failed

Not Tested

Total test items

Result Remark

102

MCMC MTSFB TC T011:2014

9.5 References

No Test Case Title

1 HbbTV 0.9 Validates products against HbbTV 1.1.1 Release by HbbTV consortium

2 TNT 2.0 Designed to check conformance to the TNT 2.0 Terminal

Specification.

1. Tests to check conformance with the HbbTV 1.2.1 profile of DASH

2. Tests to check DRM conformance for both Marlin &

Microsoft

PlayReady when integrated with HbbTV

3 TDT Hibrida This test suite comprises of test cases covering

1. Device certification validation

2. Supported Audio codecs, including 5.1 surround sound

3. Aspect ratio conformance

4. Video seeking

Remark

103

MCMC MTSFB TC T011:2014

Acknowledgements

Members of the Multimedia Terminal Working Group under the Malaysian Technical

Standards Forum Berhad (MTSFB)

Jaafar Hj. Mohamad Abu Bakar (Chairman) Hanitek Sdn Bhd

SIRIM QAS International Sdn Bhd

Al Hijrah Media Corporation (TV Alhijrah)

Syaida Syarafina binti Sohaimi (Secretary)

Hafizal Ariffin/

Suffian Yahya

Tan Chin Aik

Leong Yan Yoong/

Panna Dey

Er Yong Hwa/

Sam Choong/

Yap Chuang Hing

Sharad Sadhu/

Toni Fiedler

Asian Broadcasting Networks (M) Sdn Bhd

Dolby Laboratories Inc.

Eastool Solution Sdn Bhd

Fraunhofer IIS

Guillemard Engineering Services Ir. Abu Fatah Sanusi/

Ir. Mohd Jaafar Mohd Daud

Affendi Mohamed/

Heng Lay Peng/

Lee Jiun Huei/

Lui Yuh Yi

Hamzah Burok/

Muhammad Zakwan Mohd Zaki/

Norazlina Dato Ghazali

Dr Ahmad Zaki/

Sukumar Lechmanan

Mazlan Haji Mahdi/

Mustafa Kamal/

Zul bin Deresid

Biswas Raj a/l R.P Rajan/

Pang Chieng Yong/

Vemalarajah Thyagarajah

Magli Alias

Aw Eng Soon/

Mohd Rizal Lim/

Tan Beng Sen

Jonathan Yong

Chin Ket Ming/

Parthiban Sappiah

Abd. Muttalib V. H Usman/

Aida Razana Omar/

Hafizah Zainal Abidin/

Nurhafenah Abdul Jalil/

LG Electronics (M) Sdn Bhd

Malaysian Technical Standards Forum Berhad

(MTSFB)

Media Prima Berhad

MyTV Broadcasting Sdn Bhd

Panasonic AVC Networks Kuala Lumpur

Malaysia Sdn Bhd

Radio Television Malaysia (RTM)

Rohde & Schwarz Malaysia Sdn Bhd

Samsung Malaysia Electronics (SME) Sdn Bhd

Sharp (M) Sdn Bhd

SIRIM QAS International Sdn Bhd

104

MCMC MTSFB TC T011:2014

Yuzie Aznita Mat Yasin

Chin Ket Ming/

Jonathon Yong/

Muzaffar Fakhruddin/

Stephen Anthony Cleary

Leong Sung Boon/

Sim Yat Koon/

Yasuhiro Ota

Sony EMCS (M) Sdn Bhd

Toshiba (M) Sdn Bhd

Members of the Testing Material Sub Working Group of the Multimedia Terminal Working

Group (MMT WG) under the Malaysian Technical Standards Forum Berhad (MTSFB)

Muzaffar Fakhruddin (Team Leader) Sony EMCS (M) Sdn Bhd

Yuzie Aznita Mat Yasin (Secretary)

Hafizal Ariffin/

Suffian Yahya

SIRIM QAS International Sdn Bhd

Al Hijrah Media Corporation (TV Alhijrah)

Dolby Laboratories Inc. Leong Yan Yoong/

Panna Dey

Jaafar Hj. Mohamad Abu Bakar

Affendi Mohamed/

Heng Lay Peng/

Lui Yuh Yi

Hanitek Sdn Bhd

LG Electronics (M) Sdn Bhd

Hamzah Burok/

Muhammad Zakwan Mohd Zaki/

Norazlina Dato Ghazali

Sukumar Lechmanan

Hezal Zainal Abidin/

Mazlan Mahdi

Vemalarajah Thyagarajah

Malaysian Technical Standards Forum Berhad

(MTSFB)

Media Prima Berhad

MyTV Broadcasting Sdn Bhd

Panasonic AVC Networks Kuala Lumpur

Malaysia Sdn Bhd

Radio Television Malaysia (RTM) Ahmad Afandi/

Magli Alias

Mohd Rizal Lim

Zainuddin Md Zainon

Parthiban Sappiah

Abd. Muttalib V. H Usman/

Fauziah Fadzil/

Khairunnisa Ab. Halim/

Syaida Syarafina Sohaimi

Stephen Anthony Cleary

Leong Sung Boon/

Sani Yahya

Rohde & Schwarz Malaysia Sdn Bhd

Samsung Malaysia Electronics (SME) Sdn Bhd

Sharp (M) Sdn Bhd

SIRIM QAS International Sdn Bhd

Sony EMCS (M) Sdn Bhd

Toshiba (M) Sdn Bhd

105

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents