Installation and Adjustment Instructions

Installation and Adjustment Instructions
1. Monitor Mounting Adapter (Pg. 12-18)
VESA LCD mount shown, other options available
Installation
and Adjustment Instructions
2. Monitor Head - Rotation (Pg. 22)
Monitor
Rotation Adjustment
Quick
Setup
3. Height Locking Lever (Pg. 25)
Adjustable Height Monitor (AHM) Arm
Locks the arm at a desired height
4. Counter Balance (Pg. 27)Medical Facility Responsibility
Used to adjust for zero movement.
It is the responsibility
of the
5. Extension
Arm (Pg.
26)end user to ensure all aspects of the installation are covered by following the full manual at:
http://www.amico.com/pdf/accessories/AHM_Manual.pdf
6’’ extension
arm shown
6.Mounting Adapter (Pg. 6-10)
MON adapter shown for MRS rail
Installation
Tools & Reference
7. Monitor Head - Tilt (Pg. 21)
**
Tilt Adjustment Handle
AHM MONITOR ARM
8. Cable Management (Pg. 29)
1
1 Monitor
Mounting
Adapter
Manages
the cables
of the Monitor
Hex key (1/8”, 3/16”, M3, M4) - 1
2
VESA LCD mount shown, other options available
for better organization.
3
2 Monitor Head - Rotation
4
Monitor Rotation Adjustment
3 Monitor Locking Lever
5
Locks the arm at a desired height
6
Philips screw driver
4 Counter Balance
Used to adjust for zero movement
5 Extension Arm *
Socket wrench (12mm, 1/2”) - 1
6” extension arm shown
6 Mounting Adapter
MON adapter shown for MRS rail
7 Monitor Head - Tilt
7
7
Tilt Adjustment Handle
8 Cable Management
Adjustable wrench
8
** Not provided by Amico
Manages the cables for better organization
* If requested
1. Installation to Structure
2. Installation to Monitor
4 x 1/4-20 Set screws
Use 1/8” (3mm) hex key
to tighten
Insert screws through M4 holes
into back of monitor (4x)
*
*WARNING: Never attempt to mount or remove the arm from the rail when a monitor is installed.
*WARNING: Support AHM arm until the set screws are tightened, AHM arm can slide down when
set screws are not tightened.
Toll Free Tel: 1.877.264.2697 l Tel: 905.763.7778
Fax: 905.763.8587
* LCD mount shown, for other monitor styles, refer to manual.
Amico Accessories | www.amico.com
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada
Installation and Adjustment Instructions
Quick Adjustment Reference
Adjustable Height Monitor (AHM) Arm
A. Rotation (AHM Side to Side)
To rotate at first arm
B. Head Tilt
To rotate at second arm
Hex
Rotate End Point
*
Rotate Mid Point
* If applicable
C. Rotation (Monitor Head Side to Side)
D. Height Locking Lever Adjustments
Height Locking Lever:
Rotate Counter-Clockwise
to Release
Rotate Clockwise to Lock
Insert Height Locking Lever
To adjust arm height, always be sure to loosen the height locking lever first.
E. Counter Balance
F. Cable Management
Insert cables into cable guide, then squeeze cable guide and press onto the bottom of the AHM.
Height Locking Lever
Counter Balance Bolt (1/2”)
Cable Guide
Bottom Side of Cable Cover
Counter Balance Bolt (1/2”)
Loosing or tightening this bolt will
adjust the resistance of the arm.
Opening to the cover
When properly counterbalanced, arm should
remain in neutral position when unlocked.
Grooves
Bottom Side of the AHM Arm
Cable Cover
Cable Guide
Cable Guide
Bottom of the
AHM Arm
Toll Free Tel: 1.877.264.2697 l Tel: 905.763.7778
Fax: 905.763.8587
Amico Accessories | www.amico.com
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement