Hand Dryer - JD MacDonald

Hand Dryer - JD MacDonald
Hand Dryer
Operating Instructions and Parts Manual
A pplause Automatic Hand Dr yer
PLEASE CAREFULLY READ THROUGH THIS MANUAL BEFORE USING THE PRODUCT.
OBSERVING ALL SAFETY INFORMATION, WARNINGS AND CAUTIONS WILL PROTECT
YOURSELF AND OTHERS. PLEASE KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
361
MODEL : HDAPPSS
(14-3/16 " )
MODEL : HDAPWHT
190
(7-1/2 " )
250
(9-7/8 " )
MODEL : HDAPSSS
146
(5-3/4 " )
DIM’S
mm(inch)
TECHNICAL SPECIFICATIONS
PERFORMANCE DATA
ITEM CATEGORY
Operating Voltage
Output Warm Air Volume
220-240VAC, 50/60Hz, 4.16A, 1.0kW
151M3/h {89CFM}
Output Warm Air Temp
65°C at ambient T=25°C
Output Air Speed
12m/s [43.2km/hr]
Motor Type
0.1kw, 2800rpm, Dual Ball Bearings
Motor Thermal Protection
Auto Resetting Thermostat turns unit off at 105°C
Heater Element
900W @ 220-240VAC, Nichrome 64W
Heater Thermal Protection
Auto Resetting Thermostat turns unit off at 85°C, Resets at 75°C
Drying Time
Less than 30 seconds
Circuit Operation
Infrared Automatic, self adjusting
Sensor Range
100mm to 250mm, adjustable; standard 170mm± 20mm
Timing Protection
1 minutes auto shut off
Timing Duration
10 seconds delayed turn off after last sensor read
Sound Level
55.1dB @ 2m
Cover Type
Formed Steel, 1.2mm
Cover Finish
White epoxy finish, Bright on stainless steel, Satin on stainless steel
Net Weight
4.6Kg
Shipping Weight
5.2Kg
Unit Size
250(W) x 361(H) x 146(D)mm
Input
VAC
Motor
Vac Inrush A(W)
Heater
Operating A (W)
Vac
Inrush / Operating A(W)
Total
Inrush A(W)
Operating A(W)
220
220
0.57 (126)
0.37 (84)
220
3.43 (757)
4.00 (883)
3.80 (841)
230
230
0.59 (138)
0.39 (92)
230
3.59 (827)
4.18 (965)
3.98 (919)
240
240
0.62 (150)
0.41 (100)
240
3.75 (900)
4.37 (1050)
4.16 (1000)
1
www.asijdmacdonald.com.au
ASI JD MacDonald Pty .Ltd.
www.asijdmacdonald.com.au
1800 023 441
Instructions and Parts Manual
Hand Dryer Operating
A pplause Automatic Hand Dr yer
General safety information:
This product is intended
for installation by a qualified service person.
Disconnect power at the
source before installing or servicing.
Failure to properly ground
unit could result in severe electrical shock
and/or death.
All units must be supplied
with a 3-wire service. The ground wire must
be connected to the dryer's backplate.
-- NOTE: Do not install dryer over washbasin -Installation
1. Make sure the power source is switched off. Installation must be carried out in accordance with
the current edition of the local wiring regulations code having jurisdiction. Installation should be
performed only by a qualified electrician.
2. Place template against wall at desired height (see mounting height recommendations) and mark
locations of 4 mounting holes and wire service entry at knockout (KO) location.
Note: For two or more dryers, dryers should be no closer than 610mm on center.
3. Remove and retain 2 cover screws and cover.
4. For in-wall (concealed) power supply - Provide supply wire to KO location according to local code
and attach securely to chassis at KO with appropriate strain relief connector (not supplied).
5. Attach dryer to wall. For wood wall/studs use M6 screws at length that will ensure 25mm min.
stud penetration. For masonry walls use expansion bolts or anchors for M6 screws to ensure
penetration 6mm deeper than anchor. Shim if necessary to ensure base plate is flat against wall.
6. Connect supply and ground wires to terminal block where indicated or connect supply wires to terminal
block where indicated and connect ground wire to base plate with ground screw (Connections: A.
Connect the live wire (colored Brown or Black) to the terminal block marked "L1". B. Connect the
neutral wire (colored White or Grey) or connect the second live wire (colored Red or Orange) to the
terminal block marked "N/L2". C. Connect the ground wire (colored green or green and yellow or bare
conductor) to the terminal block marked " " or to the green screw marked " "). Colors of live and
neutral wires depend on voltage of supply service and requirements of Building and Electrical Code
having jurisdiction.
7. Replace cover. Do not over-tighten screws.
Packing List
Quantity
Self-Threading Screws
4
Plastic Expansion
2
anchor
4
Dryer
1
Security hex driver
1
Manual
1
Mounting template
1
Power cord
1
www.asijdmacdonald.com.au
ASI JD MacDonald Pty .Ltd.
www.asijdmacdonald.com.au
1800 023 441
Instructions and Parts Manual
Hand Dryer Operating
A pplause Automatic Hand Dr yer
Recommended mounting heights
Men
Women
Children 4-7 years
Children 8-10 years
Children 11-13 years
Children 14-16 years
Handicaped
- from bottom edge of dryer above finished
floor (AFF)
1270mm
1194mm
889mm
991mm
1092mm
1194mm
1016mm
Reference ADAAG
AFF (maximum)
Reach LIMIT (unrestricted)
All Approaches
Operation
1219mm
Circuit Diagram
Black
Brown
Black
L
N
Black
Blue
Capacitor
Black
G/Y
Heater
G
MO2 HE2
L
Transistor
Power Switch
MO1 HE1
White
No-touch operation.
Shake excess water from hands.
Place hands under the outlet to start operation.
Rub hands lightly and rapidly.
Stops automatically after hands are removed.
Sensor Adjustment Control:
Clockwise: Increases the sensing range(+)
Counterclockwise: Decreases the sensing range(-)
DO NOT OVERTURN!
N
VR FOR SENSOR
Circuit Board Module
Gray
G/Y
G
Y2
Wave Filter
ON
1
Sensor module
Cleaning and Maintenance
Periodic cleaning of the unit is recommended to ensure optimum performance.
Disconnect the electrical supply.
Remove the two cover-mounting screws.
Remove the cover.
Clean all dust lint from the interior of the dryer.
Wipe the cover with a damp cloth and mild
cleaning solution. Do not Soak. Never use
abrasives to clean the cover.
Replace the cover. Do not over tighten the screws.
Warranty
This dryer is designed and manufactured to provide years of dependable performance.
Component parts are guaranteed to be free of defects in material and workmanship for a period of
one year. This guarantee will be honored provided that the dryer is installed and maintained in
accordance with the instructions. Parts damaged during the installation are the purchaser's
responsibility. The ASI JD MacDonald warranty covers defects exclusively, and only liability for
the replacement of defective parts will be accepted. This warranty does not cover wear and tear,
or misuse and abuse.
3
www.asijdmacdonald.com.au
Instructions and Parts Manual
Hand Dryer Operating
A pplause Automatic Hand Dr yer
ASI JD MacDonald Pty .Ltd.
www.asijdmacdonald.com.au
1800 023 441
Troubleshooting
Symptom
If the dryer will not run
Corrective Actions
First ensure that the breaker supplying the dryer is operational.
If it is, disconnect the power and remove the dryer cover.
Check for obstructions blocking the rotation of the blower and
clear any found. If it spins freely, check the motor and
thermostat for proper operation out of the unit. Replace any
failed items. Taking suitable precautions to avoid shock hazard,
reconnect the power and check for voltage at the terminal
block. If there is power and the dryer will not run, replace the
timer assembly and/or sensor module.
If the dryer cycles by itself, or runs
all the time, or shuts off by itself
while in mid-cycle
Ensure that there is no obstruction on or in front of the
infra-red sensor. Clean any dirt off the sensor lens. Check for
voltage spikes on power line. If the problem persists, replace
the timer assembly and/or the sensor module.
If the element gets hot but the fan
motor does not turn
Disconnect the power. Remove the dryer cover and check for
obstructions in the fan housing. Damaged fans must be
replaced. If there are no obstructions, replace the motor.
If the unit runs but makes a
buzz noise
If the fan motor runs but the element
does not get hot (Dryer blows cold air)
If the motor makes ticking/winding
noise when it runs
Disconnect the power. Remove the dryer cover and check the
fan for obstructions and/or rubbing on the housing as it
rotates. Remove any obstructions and replace fan if the
rubbing condition exists.
Disconnect the power and remove the dryer cover. Check for
loose or damaged wires. Remove the blower housing.
Check the element for signs of burning or breakage. Damaged
element must be replaced. If the element does not appear
damaged, disconnect it at the timer assembly and check
element wire continuity (see tech spec). An open circuit
indicates damage to the element wire and to the integral
temperature limit control (TLC). Separate the TLC and test for
open circuit. If this is the case, replace the element and/or the
thermostat.
Disconnect the power. Replace the motor.
4
www.asijdmacdonald.com.au
Instructions and Parts Manual
Hand Dryer Operating
A pplause Automatic Hand Dr yer
ASI JD MacDonald Pty .Ltd.
www.asijdmacdonald.com.au
1800 023 441
Repair parts list
Key Part #
1
2
3
4
A0333
A0132
A0333
A0061
5
6
7
8
9
10
11
12
13
14
15
16
17
A0102
A0011
A0133
A0010
A0183
A0146
A0334
A0335
A0336
A0337
A0338
A0339
A0110
18
19
20
A0350
A0340
A0341
A0342
A0343
Description
Base plate
CAUTION Label
240VAC-8A
Terminal Label
Timer assembly
220-240VAC
Motor Capacitor
220-240VAC 1.2uF
Grounding screw with cup
Mylar shieldwith LNG marked
Terminal block
Nylon cable clamp
Nylon hole bushing
Power line deduction
Power cord
Blower mounting bracket
Blower housing - RH
Blower wheel
Blower housing - LH
Motor
1/8HP@240VAC
Heater assembly
Qty
Key Part #
21
22
23
1
1
24
25
26
27
A0345
A0346
A0347
A0348
A0349
A0124
-
28
-
29
30
-
31
32
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A0344
A0068
Description
Shell turnstile
CAUTION DISCON PWR Label
Rating Label
HDAPWHT
HDAPPSS
HDAPSSS
Security hex screw
Sensor Module, 13-6/8" cable
L - Wrench
Self threading screw M4x6,
philips pan head
Self threading screw M4x10,
philips pan head
Screw M5x10,philips pan head
Screw M4x10,philips pan head
with external tooth lock washer
Screw M3x16,philips pan head
Screw M4x6,philips pan head
Qty
1
1
1
2
1
1
2
10
4
3
2
3
1
900W@240VAC, 64W
1
Label, Circuit Diagram
1
Cover
Steel - White epoxy
Stainless Steel - Polished
Stainless Steel - Satin
5
www.asijdmacdonald.com.au
ASI JD MacDonald Pty .Ltd.
www.asijdmacdonald.com.au
1800 023 441
Instructions and Parts Manual
Hand Dryer Operating
A pplause Automatic Hand Dr yer
Assembly Diagram
1
2
5
28
4
27
13
17
3
30
6
7
8
29
16 31
12
9
10
30
11
15
14
28
32
19
18
20
21
23
22
24
25
26
6
www.asijdmacdonald.com.au
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising