Peerless LCC 18 C, CS, LCC 36 C, CS ceiling mount Installation sheet
Below you will find brief information for ceiling mount LCC 18 C, ceiling mount LCC 18 CS, ceiling mount LCC 36 C, ceiling mount LCC 36 CS. This installation sheet provides detailed instructions on how to install and assemble your ceiling mount for LCD screens. It includes a parts list, step-by-step instructions, and diagrams to help you through the process. You'll also find information on adjusting the height, tilt, and swivel of the mount, as well as securing your screen.
Advertisement
Advertisement
Installation and Assembly:
Ceiling mount for LCD screens up to 29"
Models: LCC18-C, LCC18-CS, LCC36-C, LCC36-CS
Patent Pending
Features:
• Comes in two adjustable height ranges (in 1" increments): 18"-30" and 36"-48"
• -5° to +20° adjustable tilt
• Screen can be mounted in standard position or face-down
• Portrait or landscape orientation
• Ceiling plate included
• Hardware included for wood or concrete installations
•
Snap-together cover provides sleek aesthetics and cord management
• Theft resistant security fasteners included
• VESA
®
75/100 mm compliant (Non-VESA adapter offered separately)
• Comes in black and silver
• 360° swivel action
Horizontal
Position
Vertical
Position
C US
Max UL Load Capacity: 40 lb (18.1 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Note: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307.
• This product should only be installed by a qualified professional.
• Make sure that the ceiling will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity of 40 lb (18.1 kg).
• If mounting to wood ceiling joists, make sure that mounting screws are anchored into the center of the joists. Use of an "edge to edge" stud finder is highly recommended.
•
•
•
•
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
Accessories
Lightweight Adjustable Suspended Ceiling Kit (CMJ 500)
Lightweight Suspended Ceiling Kit (CMJ 455)
Accessory Pack for CMJ 455 (ACC 455)*
Lightweight Cathedral Ceiling Plate (ACC 912)*
•
3/4" Pipe Reducer (ACC 913)*
•
Fixed Length 1 1/2" Extension Columns
(EXT models)
•
Adjustable Length 1 1/2" Extension Columns
(ADJ models)
•
Extension Column Stabilizer Kit (ACC 050)*
•
Unistrut or Structural Ceiling Plates (CMJ 300, CMJ 310)*
•
Anti-Vibration Ceiling Plates (ACC 845)*
•
I-Beam Clamps (ACC 558, ACC 559)
•
Truss Ceiling Adapter (ACC 557)*
•
Unistrut Adapter (ACC 550)
•
Extension Column Connector (ACC 109)
•
1/2" Threaded Rod (ACC 820)*
•
Threaded Rod Adapter (ACC 810)*
•
Non-VESA
®
Adapter Plates (LC models)*
*
not evaluated by UL
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill with 1/4", 3/8", 5/32", and #46 drill bits
• handsaw
• carpenter's knife
Table of Contents
Parts List .............................................................................................................................................................................. 3
Installation to Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings ............................................ 4
Installation to Concrete Ceilings ........................................................................................................................................... 5
Installing Reducer ................................................................................................................................................................ 6
Flush Mount Installation ....................................................................................................................................................... 7
Installation to Threaded Rod ................................................................................................................................................ 7
Installation to Extension Column .......................................................................................................................................... 8
Installation to Lightweight Suspended Ceiling Plate ............................................................................................................. 9
Attaching Tilt Bracket to LCD Screen ................................................................................................................................. 10
Installation of Plasma in the Vertical Position ..................................................................................................................... 11
Installation of Plasma in the Horizontal Position ................................................................................................................. 12
Installation of Vertical Covers ............................................................................................................................................. 13
Installation of Top Covers .................................................................................................................................................. 13
Installation of Tilt Covers in the Vertical Position ............................................................................................................... 14
Installation of Tilt Covers in the Horizontal Position ........................................................................................................... 14
For customer care call (800) 729-0307 or
(708) 865-8870.
2 of 14
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Parts List
Description
A
tube assembly
B
ceiling plate
C
tilt bracket
D
reducer
E
#14 x 2.5" wood screw
F
M5 x 12 mm socket pin screw
G
4 mm security allen wrench
I
H
Alligator® concrete anchor
10-32 x 3/8" socket set screw
J
hex wrench
K
M4 x 10 mm socket pin screw
L
M4 x 12 mm serrated washer head socket pin screw
M
M4 x 20 mm socket pin screw
N
#10-32 x 3/16" slotted set screw
O
retaining spacer
P
M5 x 10 mm socket pin F-type screw
Q
vertical cover
R
top cover
S
tilting cover
T
#4-24 x 3/8" flat head phillips screw
U
cable tie
V
super glue
W
alcohol pad (not shown)
LCC 18-C LCC 18-CS LCC 36-C LCC 36-CS
Qty. Part #
1 055-1520
1 580-1042
1 055-1551
Part #
055-4520
580-4042
055-4551
Part #
055-1521
580-1042
055-1551
Part #
055-4521
580-4042
055-4551
1 580-1009 580-4009 580-1009 580-4009
2 5S1-015-C03 5S1-015-C04 5S1-015-C03 5S1-015-C04
4 520-1064
1 560-9646
2 590-0097
1 520-1127
1 560-1034
4 520-1060
4 510-1079
4 520-1061
1 520-1187
4 590-5005
1 520-1164
2 590-1183
2 590-1185
2 590-1186
3 560-1715
3 590-1168
1 600-0017
1 600-0018
520-2064
560-9646
590-0097
500-2018
560-1034
520-2060
510-2079
520-2163
520-2187
590-5003
520-2031
590-4183
590-4185
590-4186
560-4715
590-1168
600-0017
600-0018
520-1064
560-9646
590-0097
520-1127
560-1034
520-1060
510-1079
520-1061
520-1187
590-5005
520-1164
590-1184
590-1185
590-1186
560-1715
590-1168
600-0017
600-0018
520-2064
560-9646
590-0097
500-2018
560-1034
520-2060
510-2079
520-2163
520-2187
590-5003
520-2031
590-4184
590-4185
590-4186
560-4715
590-1168
600-0017
600-0018
A
B
C
D
Q
V
R
S
G
E
H
J
F
I
K L
U
3 of 14
T
M
N
O
P
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation to Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings
Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (B) with two #14 x 2.5" (6 mm x 65 mm) wood screws (E) as shown using 3/8" (10 mm) socket wrench. Tighten wood screws (E) so ceiling plate (B) is firmly attached.
WARNING
• Tighten wood screws so that ceiling plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the joist. The use of an "edge to edge" stud finder is highly recommended.
Skip to step 2 on page 6.
WOOD
JOIST
CEILING
B
E
E
4 of 14
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation to Concrete Ceilings
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach ceiling plate (B) using two concrete anchors (H) and #14 x 2.5" wood screws (E) as shown in Illustration A and 1, 2, and 3 (below).
Tighten all fasteners.
WARNING
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the bolt, greatly reducing its holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer (not evaluated by UL).
metal bracket
INCORRECT
concrete metal bracket
CORRECT
concrete plaster/ dry wall plaster/ dry wall
B
CONCRETE
CEILING
H
E
Illustration A
1
concrete ceiling
H
Drill hole and insert anchor
2
B
E
H
Place ceiling plate over anchor and secure with screw
3
E
H
After repeating step one tighten all fasteners
5 of 14
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installing Reducer
Thread reducer (D) onto tube assembly (A) until tight.
Insert set screw (I) into reducer as shown in figure 2-1.
Tighten screw using hex wrench (J). Note: Set screw (I) is used to jam against the threads of tube assembly to prevent any excess movement.
To adjust height of tube assembly (A), remove socket pin screw and two lock washers using 4 mm security allen wrench (G) and adjust to desired height as shown in figure 2-2.
D figure 2-1
I
B
A
LOCK WASHERS
SOCKET PIN SCREW
A figure 2-2
6 of 14
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Flush Mount Installation
Screw reducer (D) into ceiling plate (B) until notch in reducer is aligned with one of the four holes in ceiling plate and set screw (I) is at least partially covered by ceiling plate as shown in figure 3-1.
Secure reducer with one M5 x 10 mm F-type socket pin screw (P) using security allen wrench (G) as shown in figure 3-2. Note: Slotted set screw (N) is used to jam against the threads of the reducer to prevent any excess movement of the tube assembly (A). Do not overtighten screw; overtightening screw will damage threads making it difficult to separate the products.
Skip to step 4 on page 10.
B
D
N
P
Installation to
Threaded Rod
Accessory ACC 810 (not evaluated by UL), threaded rod adapter, is required.
Screw threaded rod adapter (ACC 810) into extension column connector (ACC 109). Align slot in threaded rod adapter with one of the top holes in extension column connector. Insert and tighten one #10-32 x 3/
8" socket pin screw provided with extension column connector through extension column connector into slot on threaded rod adapter using 4 mm security allen wrench (G). See figure 3-3.
Align slot in reducer (D) to one of the bottom holes in extension column connector. Insert and tighten one
#10-32 x 3/8" socket pin screw provided with extension column connector through extension column connector into slot in reducer. See figure 3-4.
Note: Slotted set screws provided with extension column connector are used to jam against the threads of each connecting joint to prevent any excess movement. Do not overtighten screws; overtightening screws will damage threads making it difficult to separate the products.
Skip to step 4 on page 10.
7 of 14
I figure 3-1
A figure 3-2
1/2 -13 THREADED
ROD
ACC 810 (SOLD
SEPARATELY)
SET
SCREW
THREADED
ROD
ACC 810
SLOT
SLOT
ACC 109
(SOLD
SEPARATELY)
ACC 109
SOCKET
PIN
SCREW
figure 3-3
THREADED
ROD
SLOT
D
ACC 109
SET
SCREW
ACC 810
D
SLOT
SOCKET
PIN
SCREW
figure 3-4
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation to Extension Column
Screw extension column (EXT or ADJ
Series) to ceiling plate (B). Align the notch with one of the four holes in the ceiling plate and secure extension column with a M5 x
10 mm socket pin screw (P) using security allen wrench (G). See figure 3-5.
Note: Slotted set screw (N) is used to jam against the threads of the reducer to prevent any excess movement of the extension column. Do not overtighten screw; overtightening screw will damage threads making it difficult to separate the products.
B
EXTENSION
COLUMN
(UL Listed EXT or
ADJ Series)
Sold Separately
Screw extension column connector
(ACC 109) to extension column. Align slot in extension column with one of the top holes in extension column connector. Insert and tighten one #10-32 x 3/8" socket pin screw provided with projector through extension column connector into slot on extension column using security allen wrench (G). See figure 3-6.
SLOT
Screw reducer (D) to extension column connector. Align reducer to one of the bottom holes in extension column connector. Insert and tighten one #10-32 x
3/8" socket pin screw provided with connector through extension column connector into slot in reducer using security allen wrench (G). See figure 3-7.
EXTENSION
COLUMN
CONNECTOR
(SOLD
SEPARATELY)
SLOT
Note: Slotted set screws provided with extension column connector are used to jam against the threads of each connecting joint to prevent any excess movement. Do not overtighten screws; overtightening screws will damage threads making it difficult to separate the products.
D
P
EXTENSION
COLUMN
SET SCREW
ACC 109
figure 3-5 figure 3-6
N
B
EXTENSION
COLUMN
SLOT
SOCKET PIN
SCREW
Skip to step 4 on page 10.
EXTENSION
COLUMN
ACC 109
SLOT
SET SCREW
B
SOCKET PIN
SCREW
ACC 850 - EXTENSION COLUMN
CONNECTOR WITH CORD MANAGEMENT
- MAY BE USED IN PLACE OF EXTENSION
COLUMN CONNECTOR. (SOLD
SEPARATELY)
8 of 14 figure 3-7
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation to Lightweight Suspended Ceiling Plate
Refer to instruction sheet for lightweight suspended ceiling plate (CMJ 455) for attachment of ceiling plate to ceiling.
Screw extension column (EXT or ADJ
Series) to
retaining collar in ceiling tray
.
Align the notch with one of the four holes in retaining collar and secure extension column with one M5 x 10 mm socket pin screw (P) using security allen wrench (G). See figure 3-8.
Note: Slotted set screw (N) is used to jam against the threads of the reducer to prevent any excess movement of the extension column. Do not overtighten screw; overtightening screw will damage threads making it difficult to separate the products.
Screw extension column connector to extension column. Align slot in extension column with one of the top holes in extension column connector.
Insert and tighten one 10-32 x 3/8 socket pin screw provided with connector through extension column connector into slot on extension column using security allen wrench. See figure
3-9.
Screw reducer (D) to extension column connector. Align slot in reducer to one of the bottom holes in extension column connector. Insert and tighten one 10-32 x 3/8 socket pin screw provided with connector through extension column connector into slot in reducer using security allen wrench. See figure 3-10.
Note: Slotted set screws provided with extension column connector are used to jam against the threads of each connecting joint to prevent any excess movement. Do not overtighten screws; overtightening screws will damage threads making it difficult to separate the products.
LIGHTWEIGHT
SUSPENDED
CEILING PLATE
(SOLD SEPARATELY)
EXTENSION
COLUMN
(UL Listed EXT or
ADJ Series)
Sold Separately
EXTENSION
COLUMN
CONNECTOR
(SOLD
SEPARATELY)
SLOT
N
EXTENSION
COLUMN (SOLD
SEPARATELY)
figure 3-8
EXTENSION
COLUMN
SET SCREW
ACC 109
RETAINING COLLAR
P
SOCKET PIN
SCREW
figure 3-9
SLOT
SLOT
D
ACC 109
SET SCREW
EXTENSION
COLUMN
D
SOCKET PIN
SCREW
ACC 850 - EXTENSION COLUMN
CONNECTOR WITH CORD
MANAGEMENT - MAY BE USED IN PLACE
OF EXTENSION COLUMN CONNECTOR.
(SOLD SEPARATELY)
9 of 14 figure 3-10
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Attaching Tilt Bracket to LCD Screen
Note: This product is designed to accommodate screens with VESA
®
compliant hole patterns. For safe mounting, please make sure that mounting screws turn at least three complete turns in the screen inserts.
FOR VESA 75 MOUNTING PATTERN:
1) Choose hole pattern indicated below. 2) Attach tilt bracket (C) to back of screen using four M4 x 10 mm screws (K) as indicated below. 3) If hole pattern is in a pocket, attach tilt bracket to back of screen using four M4 x 20 mm screws (M) and four retaining spacers (O) as indicated below. Tighten all security screws with security allen wrench (G).
K
C
For screens with a hole
pattern in a pocket, spacers (O) go between tilting bracket (C) and screen.
BOTTOM OF SCREEN
Note: LCD screen may appear slightly different than illustrated.
FOR VESA 100 MOUNTING PATTERN:
1) Choose hole pattern indicated below. 2) Attach tilt bracket (C) to back of screen using four M4 x 10 mm screws (K) as indicated below. Tighten all security screws with security allen wrench (G).
Note: If installing LCD screen model Sharp
®
LC-13E1U, LC-15E1U, LC-20E1U, or if you don't get three complete turns in the screen inserts, use four M4 x 12 mm screws (L) instead of four M4 x 10 mm screws (K).
K
C
BOTTOM OF SCREEN
Note: LCD screen may appear slightly different than illustrated.
10 of 14
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation of Screen in the Vertical Position
Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5-1). Leave approximately
3/16" of thread exposed (see figure 5.2).
COLUMN
BRACKET
3/16"
EXPOSED
THREAD
F fig. 5-1 fig. 5-2
Hook tilt bracket (C) onto column bracket (see figure 6-1). Secure with two M5 screws (F) (see figure 6-2). Adjust tilt
(20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).
Note: Cable ties (U) are provided for optional cord management.
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the LCD screen.
fig. 6-1
C
COLUMN
BRACKET
F
11 of 14 fig. 6-2
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation of Screen in the Horizontal Position
Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5-1). Leave approximately
3/16" of thread exposed (see figure 5-2).
COLUMN
BRACKET
3/16"
EXPOSED
THREAD
F fig. 5-1 fig. 5-2
Hook tilt bracket (C) onto column bracket (see figure 6-1). Secure with two M5 screws (F) (see figure 6-2). Adjust tilt
(20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).
Note: Cable ties (U) are provided for optional cord management.
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the LCD screen.
fig. 6-1
C
COLUMN
BRACKET
F
12 of 14 fig. 6-2
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation of Vertical Covers
Route cords through side channels of one vertical cover (Q). Snap two vertical covers together on tube assembly (A) so that they are perpendicular to tilt bracket (C). If necessary, use a handsaw to cut vertical covers to match the length of tube assembly.
Q
C
A
SIDE
CHANNELS
Installation of Top Covers
Snap two top covers (R) together flush with finished ceiling. Use holes in top covers to mark vertical covers (Q). Using a #46 (approx. .0810") drill bit, drill holes in vertical covers. (Note: It may be necessary to remove vertical covers before drilling holes to avoid damaging cables.) Remove top covers (R). Use glue (V) on the inside edge of one of the two top covers (R) so that the two sides will stick together when they are connected. Secure top covers to vertical covers using two #4-24 x 3/8" flat head phillips screws (T) as shown in figure 8-1.
Note: One extra flat head phillips screw (T) has been provided.
Note: Alcohol pad (W) may be used for clean up of glue.
R
Q
13 of 14
T fig. 8-1
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation of Tilt Covers in the Vertical Position
Using a carpenter's knife, cut out any sections of tilt covers (S) necessary to allow them to snap together over vertical covers (Q) as shown in figure 9-1. Note: Cut out sections of one tilt cover should mirror cut out sections of the other.
Use glue (V) on the inside edge of one of the two tilting covers (S) so that the two sides will stick together when they are connected. Insert tabs of tilt covers into slots of tilt bracket (C) and snap tilt covers together.
Note: Alcohol pad (W) may be used for clean up of glue.
S
C
Q fig. 9-1
Installation of Tilt Covers in the Horizontal Position
Using a carpenter's knife, cut out any sections of tilt covers (S) necessary to allow them to snap together over vertical covers (Q) as shown in figure 9-1. Note: Cut out sections of one tilt cover should mirror cut out sections of the other.
Use glue (V) on the inside edge of one of the two tilting covers (S) so that the two sides will stick together when they are connected. Insert tabs of tilt covers into slots of tilt bracket (C) and snap tilt covers together.
Note: Alcohol pad (W) may be used for clean up of glue.
Q
S fig. 9-1
C
14 of 14
© 2004 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Adjustable height
- Adjustable tilt
- Swivel action
- Portrait or Landscape orientation
- Theft resistant security fasteners
- VESA 75/100mm compliant
- Comes in black and silver
- Snap-together cover for sleek aesthetics and cord management
- Ceiling plate for wood or concrete installations
- UL listed