105EInstructionManual

105EInstructionManual
Gr rayers ®
Р "Plus >
PROFESSIONAL LANDSCAPER
lA-POWER
Instruction Manual
. Introduction
. Specifications
. General Power
Tool Safety Warnings
. Charging Procedure
. Turn On/Off the sprayer
. Nozzle
. Application
. Parts Breakdown
. Important Return
Safety Instructions
. Statement of Limited
Warranty
. Troubleshooting
1. Introduction
3. General Power Tool Safety Warnings
This manual contains information for the proper assembly,
operation and care of your sprayer. Carefully read and follow the
instructions contained in this manual before using your sprayer.
2. Specifications
Target Market Professional Landscaper
Power 20V Lithium-ion battery
Capacity US Gallons (Ltr) 4(15)
Dry Weight Ibs. (kg) 9.6 (4.35)
Working pressure 35 psi Continuous
Spray-Plus™ with lock pin,
Spray Gun brass spindle & filter
Wand 20”powder coated
brass wand
Hose Flex+Plus™ 51” Rubber
- Brass Nozzle
Nozzle
- 2 Plastic Fan Nozzles
Comfort+Plus™ deluxe
Shoulder Strap shoulder straps and padding
Mouth Opening (cm) EZ-Fill™ 5.25 (14)
Check Valve Yes
Warranty 1 year commercial use
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The
information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help
you recognize this information.
/N DANGER!
Indicates an imminently hazardous situation which, if
not avoided will result in death or serious injury.
/\ WARNING!
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
/\ CAUTION
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
WARNING:
IMPROPER USE OR FAILURE TO FOLLOW INSTRUCTIONS CAN
RESULT IN EXPLOSION CAUSING SERIOUS EYE OR OTHER INJURIES.
FOR THE SAFE USE OF THIS, YOU MUST READ AND FOLLOW ALL
INSTRUCTIONS.
Do not leave a pressurized sprayer in the hot sun. Heat can cause
pressure build up, resulting in possible explosion. Do not store or
leave solution in the tank after use. Always wear goggles, gloves,
long sleeve shirt, long pants and full foot protection while
spraying. Do not attempt to modify this sprayer. Replace parts only
with manufacturer's original parts. Never spray flammable, caustic,
acidic, chlorine, bleach or other corrosive solutions. Always read
and follow manufacturer's instructions before using this sprayer
because some chemicals may be hazardous when used with this
sprayer.
Handling the brass parts of this product will expose you to a
chemical known to the state of California to cause birth defects or
other reproductive harm.
Wash hands after handling.
CAUTION:
* PRE-USE CHECK: Before each use, check the tightness of the hose
to ensure the hose is securely attached to the shut-off assembly.
Ensure that all nozzles and wand connections are tight.
* Do not exceed a tank solution temperature of 120°F / 49°C.
NOTE: Residual water may be present in the tank and hose due to
quality and performance testing performed on the sprayer.
3.1 Battery Safety
This sprayer is designed to operate with a 20V lithium-ion battery
ONLY. Use of any other batteries with the sprayer may cause serious
harm or injury to the operator and serious damage to the sprayer.
WARNING:
For safe operation of the charger, read this manual before use.
The battery pack does not come fully charged out of the box.
Before operating the battery pack and charger, read the safety
instructions and follow the charging procedures outlined below.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY PACKS
(a) Do not incinerate the battery pack even if it is severely damaged or is
completely worn out. The battery pack can explode if exposed to flames or
high heat. Toxic fumes and materials are created when battery packs are
bumed.
(b) Do not charge or use battery in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Inserting or removing the
battery from the charger may ignite the dust or fumes.
(c) If battery contents come into contact with skin, immediately wash area
with mild soap and water. If battery liquid gets into the eye, rinse water over
the open eye for 15 minutes or until irritation ceases. If medical attention is
needed, see a doctor immediately. The battery electrolyte for lithium-ion
batteries is composed of a mixture of liquid organic carbonates and lithium
salts.
P.2
(d) Contents of opened battery cells may cause respiratory irritation. If
respiratory irritation is experienced due to exposure, move person to a
well-ventilated area immediately. If symptoms persist, seek medical
attention.
WARNING:
Burn hazard. Battery liquid may be flammable if exposed to sparks or
flames.
* Charge the battery packs only in Sprayers Plus chargers
* ОО NOT splash or immerse in water or other liquids. This may cause
premature cell failure.
* DO NOT store or use the tool and battery pack in locations where the
temperature may reach or exceed 105°F(40°C) (such as outdoor sheds or
metal buildings in the summer season).
Never attempt to open the battery pack for any reason. If battery pack
casing is cracked or damaged, do not insert into charger. Do not crush,
drop or damage battery pack. Do not use a battery pack or charger that has
received a sharp blow, been dropped, run over or damaged in any way.
Damaged battery packs should be returned to a service center for
recycling.
WARNING:
Fire hazard. Do not store or carry the battery in such a way that metal
objects can contact exposed battery terminals. For example, do not place
battery in aprons, pockets, toolboxes, product kit boxes, drawers, etc.
To prevent fire risk while transporting batteries, ensure battery terminals do
not come in contact with conductive materials such as keys, coins, hand
tools and the like. The US Department of Transportation's Hazardous
Material Regulations (HMR) prohibits the transport of lithium-ion batteries
in commerce or on airplanes (i.e., packed in suitcases and carry-on
luggage) UNLESS they have proper short-circuit protection. When
transporting individual batteries, make sure that the battery terminals are
protected and well insulated from materials that could contact them and
cause a short circuit.
NOTE: Lithium- ion batteries should NOT be put in checked baggage.
3.2 Storage Recommendations
The best storage place is one that is cool and dry — away from direct
sunlight and excess heat or cold.
Long-term storage will not harm the battery pack or charger.
4. Charging Procedure
Sprayers Plus chargers are designed to charge Sprayers Plus 20V battery
packs only.
Charging lights
1. Plug the charger into an appropriate outlet before inserting the battery pack.
2. Insert the battery pack into the charger.
3. An illuminated red light indicates that the battery is being charged.
4. When the illuminated light changes from red to green, the battery is fully
charged.
5. Aflashing red light indicates a charging error. Go to dealer for help.
Battery power light
(Only works when charger is not plugged into the power outlet)
1. The 3 blue LED lights indicate the battery power.
2. 3 illuminated lights indicate that the battery is fully charged.
3. 1 illuminated light indicates low battery levels.
« 20V Lithium-ion battery
( Parts: K7039 )
* 20V Charger
( Parts: K8003 )
P.3
LEAVING THE BATTERY IN THE CHARGER
The charger and battery pack can be left connected with the green LED
light glowing. The charger will keep the battery pack fresh and fully
charged.
4.1 IMPORTANT CHARGING NOTES
(1) The longest life and best performance can be obtained if the battery
pack is charged in an environment where the air temperature is
between 65°F and 75°F (18°C-24°). DO NOT charge the battery pack
in an environment where the air temperature drops below 40°F
(+4.5°C), or rises above +105°F (+40.5°C). Follow these guidelines to
prevent serious damage to the battery pack.
(2) The charger and battery pack may become warm to touch while
charging. This is normal and does not indicate a problem. To facilitate
the cooling of the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal shed or an
uninsulated trailer.
(3) If the battery pack does not charge properly:
a.) Check current at the outlet or receptacle by plugging in a lamp or
other appliance.
b.) Check to see if outlet or receptacle is connected to a light switch
which turns the power off when you turn off the lights.
c.) Move charger and battery pack to a location where the surrounding
air temperature is between approximately 65°F and 75°F(18°-24°C)
d.) If charging problems persist, take the tool, battery pack and charger
to your local service center.
(4) The battery pack should be recharged when it fails to produce sufficient
power on jobs that were previously easy to complete. DO NOT
CONTINUE with use under these conditions. Follow the charging
procedure to recharge the battery. You may also charge a battery used
pack when ever you desire with no adverse effect to the battery pack.
(5) Foreign materials of a conductive nature such as, but not limited to,
steel wool, aluminum foil, or any buildup of metallic particles should be
kept away from charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity. Unplug
charger before attempting to clean.
(6) Do not freeze or immerse charger in water or any other liquid.
WARNING:
Shock hazard. Do not allow any liquid to get inside charger.
Never attempt to open the battery pack for any reason. If the
plastic housing of the battery pack breaks or cracks, retum to
a service center for recycling.
POWER BATTERY
Li-ion 20V 2.2Ah/39.6wh
WARNING
To reduce the risk of fire or burns, do not
disassemble, crush, puncture or short
external contacts.
© СЕ ® © д
4.2 INSTALLING AND REMOVING THE
BATTERY PACK FROM THE SPRAYER
WARNING:
Make sure switch is in the off position.
To install battery pack:
Insert battery pack into tool until a "click" is heard. Make sure battery pack
is fully seated and latched into position.
To remove the battery pack:
Depress the battery release button and pull battery pack out of tool.
* Pull by the plug rather than pulling by the cord when disconnecting
charger. This will reduce risk of damage to electric plug and cord.
Do not use an extension cord unless it is absolutely necessary. Use of
an improper extension cord could result in risk of fire, electric shock, or
electrocution.
» An extension cord must have adequate wire size (AWG or American
Wire Gauge) for safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has more capacity
than 18 gauge. When using more than one extension to make up the
total length, be sure each individual extension cord contains at least the
minimum wire size required.
Do not operate charger with a damaged cord or plug — please have
them replaced immediately.
Do not operate charger if it has received a sharp blow, been dropped, or
damaged in any way. Take it to an authorized service center.
Do not disassemble charger; take it to an authorized service center
when service or repair is required. Incorrect reassembly may result in
risk of electrocution or fire.
Disconnect the charger from the outlet before attempting any cleaning.
This will reduce the risk of electric shock. Removing the battery pack will
not reduce the risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard household electrical
power(120 Volts). Do not attempt to use it on any other voltage.
* To install the battery *
Insert the battery into tool until an audible click is heard
E
1]
ТС
Pal
PE
* To remove the battery *
Pull the trigger towards the right. Release
the battery by pulling out from tool.
4.3 IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGERS
WARNING:
* Shock hazard. Do not allow any liquid to get inside charger.
* Do not attempt to charge the battery pack with any chargers other than
the ones included in this manual. The charger and battery pack are
specifically designed to work together.
* These chargers are not intended for any uses other than charging
rechargeable batteries. Any other uses may result in risk of fire or
electrocution.
* Do not expose charger to rain or snow
CAUTION:
When the charger is plugged into the power supply under certain
conditions, the charger can be shorted by foreign material. Foreign
materials of a conductive nature such as, but not limited to, steel wool,
aluminum foil, or any build up of metallic particles should be kept away from
charger cavities. Always unplug the charger from the power supply when
there is no battery pack in the cavity. Unplug charger before attempting to
clean.
5. Turn On/Off the sprayer
NOTE: Before starting to spray, retighten the hose clamps to avoid
contamination of the operator and of the environment.
To Turn on the sprayer:
1. Tum on the sprayer using the ON/OFF switch. LED light will illuminate to
indicate that the sprayer is ON.
2. Place the lance with the trigger valve pressed above the base of the
sprayer until the spray jet begins to spray continuously.
3. Direct the spray lance to a safe position and open the trigger valve to
begin spraying.
To turn off the sprayer:
1. Shut off the trigger valve. The internal pump pressure switch will
automatically tum off the pump (the sprayer is said to be in idle state.)
2. Tum off the sprayer using the ON/OFF switch. LED light will tum off to
indicate that the sprayer is OFF.
3. Direct the spraying lance to a safe position and open the trigger valve to
release pressure before storing the sprayer.
P4
6. Nozzles
7. Application
Nozzle Type Cone Nozzle Fan Nozzle
Material Brass Plastic
Degree 360 90/110
Outlook =
P.5
- Wear appropriate protective clothing
Head Protector a
/
Eyes Protector A
с
Dust Mask qe y
Long-Sleeved Shirt
Smock
Gloves
Long Pants
Boots
WARNING:
Use of individual protective clothing and safety
equipment is required.
WARNING:
Use the correct dose and volume of chemical according
to the product label.
WARNING:
Do not spray near people who are not using PPE,
springs, lakes and rivers.
> E E >
WARNING:
In case of an accident, remove the sprayer immediately.
P.6
8. Parts Breakdown
—K10e29
K9004
CS ve
| ¡ose
PROFESSIONAL BÉ
CA |
e
[eu 8)
| |
los > | me)
|
ДК 5
e fr |
(LU (I =
65
vos
</068
P.7
PART LIST
K1004
K1025
K3010
K7064
K7066
K7049
K3030
K4001
K4002
K7058
K7069
K7068
K4026
K4033
K4039
K5004
K5007
K5012
K7067
K7038
K7039
K7040
K7041
K7042
K7065
K7070
K8003
K7043
STRAINER
BLUE LID & SEAL W/ HANDLE
BRASS SPINDLE SET
SPRAY GUN PLUG SET (CAP, SPRING & O-RING)
20" BRASS SPRAY WAND
HOSE SET W/ CLAMPS
BUILT-IN FILTER
6” LID SEAL
CHECK VALVE
NOZZLE HOLDER
BRASS NOZZLE SET
PLASTIC FAN NOZZLE SET
SET OF 2 WASHERS FOR SPRAY GUN
VITON O-RING FOR NOZZLE
O-RING & WASHER SET FOR SPINDLE
BUCKLE & HOOK FOR SHOULDER STRAP (1 EACH)
PAIR OF SHOULDER STRAPS
2 PCS BUCKLE SET FOR SHOULDER STRAP
GUN, WAND & NOZZLE SET
20V PUMP UNIT
20V BATTERY PACK
DOOR LOCK
POWER SWITCH SEAL COVER
PANEL MOUNT FOR 20V BATTERY PACK
CONNECTION HOSE SET FOR 20V PUMP
BACK DOOR SET
20V CHARGER & TRANSFORMER
SCREEN FILTER TUBE SET
P.8
9. Important Return Safety Instructions
If it is necessary to return the sprayer for repair, always perform
the following tasks before returning the sprayer:
1. In an approved containment area, flush chemical residue
from the pump, tank and hoses.
2. Circulate fresh water through the tank, pump and hoses.
3. Indicate the type of chemicals that have been in the sprayer
with a label or tag.
4. Include complete description of operation problem, such as
how sprayer was used, symptoms of malfunction, how many
working hours per day, etc.
5. Remove the battery from the sprayer and keep it in clean and
dry conditions. Battery must accompany the sprayer when it
is returned for repairs.
Since the sprayer can contain residues of toxic chemicals, these
steps are necessary to protect the people who handle return
shipments, and to help identify issues and solutions.
10. Statement of Limited Warranty
Sprayers Plus shall warrant the equipment described in this
manual and shall repair or replace parts and components which,
under normal operation and wear, in accordance with technical
recommendations, show DEFECTS IN MATERIAL OR WORKMAN-
SHIP, based on the following conditions.
10.1 Warranty period
1 (one) year from the date of sale to the original purchaser.
10.2 Warranty application
Please visit: www.sprayers-plus.com/warranty
Sprayers Plus shall honor this warranty, free of charge, if any part
or component shows defect in MATERIAL OR WORKMANSHIP,
after final analysis at the factory.
10.3 This Warranty shall be null & void
in case of:
* Misuse of the equipment against specifications in this
manual, overwork or accidents.
Preventive / remedial maintenance performed by unautho-
rized people or parties.
* Use of parts and components not supplied by Sprayers Plus.
* Modification of the equipment or any characteristic of the
original design.
P.9
10.4 This Warranty shall exclude
Parts which show wear and tear due to use: spray nozzle,
filters, seals, rechargeable battery, hydraulic pump, electronic
panel, charger and its cables, agitator lever, belt, UNLESS
THEY SHOW DEFECTS IN WORKMANSHIP, ASSEMBLY OR
MATERIAL.
Damages resulting from accidents.
Transportation or freight of the equipment, parts, and
components in case such warranty is not approved.
Transportation and travel time of technician.
11. Troubleshooting
If sprayer is not working as expected, consider the following table before contacting technial assistance.
Fault Status
Cause
Solution
Trigger valve is not released
Trigger valve is shut
Release trigger valve
Pump is working, but
fluid is not coming
out of the sprayer
Nozzle or nozzle filter is blocked
Clean or replace nozzle/filter
Pump suction inside the
chemical tank is blocked
Trigger valve is released
Suction hose is blocked
or disconnected
Pump or hoses are leaking
Contact for technical assistance
Trigger valve is not released
Trigger valve is shut
Release trigger valve
Pump is not working
(no audible noise from pump)
while sprayer is turned ON
Pump electrical connector
is disconnected
Connect pump electrical connector
Trigger valve is released
Nozzle or nozzle filter is blocked
Clean or replace nozzle/filter
Pump wiring is broken
Pump is damaged
Contact for technical assistance
Battery is fully discharged
Recharge battery with
Sprayers Plus charger
Battery is damaged and/or
electronic module is damaged
Contact for technical assistance
Spray pressure is weak
Air accumulation inside the lance
Place the lance with the trigger
valve pressed above the base of
the sprayer until the spray jey
begins to spray continuously
Pump suction inside the chemical
tank is partially blocked
Remove obstruction and circulate
clean water to clean the hoses
Suction hose is partially blocked
Circulate clean water to clean hoses
Pump or hoses are leaking
Contact for technical assistance
Nozzle or nozzle filter is
blocked or damaged
Clean or replace nozzle/filter
ON/OFF was pressed
Pump reached maximum pressure
and pressure switch activated
Nozzle is plugged.
Rinse with clean water.
Spraying was normal
but stopped suddenly
No audible noise when pumping
Pump wiring is loose,
damaged or disconnected
Check pump wiring
Battery duration time is
shorter than usual or
battery failed to charge
New Battery
Battery is not fully charged
Charge the battery until indication
light on the charger turns green
Using third-party charger
Use Sprayers Plus certified charger
Using third-party pump
Use Sprayers Plus certified pump
Damaged cords/plugs on charger
Replace with new charger
Battery is damaged. (e.g. became
wet, cracked, broken terminal)
Used battery with more than
Battery has exceeded its
300 charge cycles
optimal number of charge cycles
Replace with new battery
P.10
Sr ravers O
P "Plus >
OF
M E-mail: [email protected]
af www .sprayers-plus.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement