INTERCHANGE CN55-15 Coil Nailer Operator's Manual
The Interchange 65530 is a powerful and versatile coil nailer designed for professional use in various applications. It can drive wire collated nails ranging from 1-1/4" to 2-1/4" (32 to 57mm) in length, making it suitable for tasks such as assembling pallets, drums, and wooden boxes. The nailer's lightweight aluminum or magnesium body ensures easy handling and reduces fatigue during prolonged use. With a magazine capacity of 250 to 400 nails, the Interchange 65530 minimizes the need for frequent reloading, increasing productivity.
Advertisement
Advertisement
Operator’s Manual
15
o
Coil Nailer
Model No. CN55-15
Item No. 65530
Drives Wire Collated Nails
1¼" to 2 ¼" / 32 to 57mm
Ask for
Genuine
INTERCHANGE
®
HWCF Nails
NOte:
Please read and fully understand the instructions in this
manual before operating the pneumatic power tool. Carefully read through this
OPERATOR’S MANUAL to ensure efficient, safe operation. It is recommended that the
MANUAL be kept readily available as an important reference when using this tool.
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Index
Model No. CN55-15
Item No. 65530
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . Page
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Tool Information
Nailer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Nail Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Safety Information
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Employer’s Responsibilities . . . . . . . . . . . . . . . . . . . . . . .9
Operating the Nailer
Air Supply, Connections & Operating Pressure . . . . . 10-11
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .12
Nail Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Testing the Nailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Methods of Operation . . . . . . . . . . . . . . . . . . . . . . . 14-15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Maintenance and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . .16
Parts Drawing/Schematics, Parts List, Parts Kits
Parts Drawing/Schematics . . . . . . . . . . . . . . . . . . . . . .17
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Parts Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
2
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Important Information
Model No. CN55-15
Item No. 65530
WARNING:
The warnings, cautions and instructions discussed in this instruction manual can not cover all possible conditions and situations that may occur . It must be understood by the operator that common sense and caution are factors which can not be built into this product, but must be supplied by the operator .
When using the tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment .
Read and understand tool labels and operating instructions, safety precautions and warnings in this manual before operating or maintaining this nailer .
Failure to follow warnings could result in DEATH or SERIOUS INJURY .
Most accidents that result from the operation and maintenance of nailers are caused by the failure to observe basic safety rules or precautions . An accident can often be avoided by recognizing a potentially hazardous situation before it occurs and by observing appropriate safety procedures .
Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the operation and maintenance instructions .
Hazards that must be avoided to prevent bodily injury or tool damage are identified as
DANGERS
or
WARNINGS
on the nailer and in this Manual .
Never allow the nailer to be operated by children or individuals who have not reviewed this manual .
OpERAtE thE NAIlER ACCORDING tO thIS mANuAl.
WARNING!
■
Always follow the tool manufacturer’s safety and maintenance instructions .
■
Always wear safety glasses with side shields when operating or servicing tools .
■
Always disconnect the air supply from the tool and empty the magazine when servicing tools .
SAVE THIS MANUAL
FOR FUTURE REFERENCE!
Interchange Brands Operator’s Manual
3
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Tool Information
Nailer Specifications: CN55-15 Coil Nailer
Tool Dimensions -
Length x Height x Width
Weight
Magazine Capacity
Recommended Operating Pressure
Model No. CN55-15
Item No. 65530
13 .19" x 11 .61" x 5 .12"
﹙335mm x 295mm x 130mm﹚
6 .33 lbs . ﹙2 .87 kgs .﹚ Aluminum Body
5 .89 lbs . ﹙2 .67 kgs .﹚ Magnesium Body
250 to 400 Nails
70 to 120 psi / 5 to 8 .5 kgs .
Applications
Assembly and Repair of Pallets, Drums, Export Wooden Boxes and Wooden Fencing .
General Construction Applications Including: Siding, Decking, Crating and Sheathing .
Nail Specifications
WARNING:
Be sure to use only the genuine nails recommended for the
CN55-15 . The use of any other nails can result in tool malfunction, leading to serious injuries .
Only the nail sizes shown in the table below can be driven with this nailer .
FASTENERS:
Wire Welded Nail Length
Shank Diameter
Head Diameter
Shank Type
1-1/4" to 2-1/4" / 32 to 57mm
0 .083" to 0 .092" / 2 .1 to 2 .3mm
0 .197" to 0 .236" / 5 .0 to 6 .0mm
Smooth, Ring, Screw
DImENSIoNS oF FASTENERS:
15˚ Coil Nails - Flat, Wire Weld Collated
Nail Length Shank Diameter Head Diameter
0 .197" to 0 .236"
5 .0mm to 6 .0mm
1-1/4" to 2-1/4"
32mm to 57mm
0 .083" to 0 .092"
2 .1mm to 2 .3mm
4
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Parts Identification
Model No. CN55-15
Item No. 65530
➑
➊
➋
➏
➐
➎
➊
Casting
➋
Cylinder Cap
➌
Safety
➍
Guide Body
➎
Magazine
➏
Trigger
➐
Grip
➑
Exhaust Cover
➍
➌
TooL AIR FITTINGS: This tool uses a minimum 1/4" N .P .T . male plug . The inside diameter should be 0 .28" ﹙7mm﹚ or larger . The fitting must be capable of discharging tool air pressure when disconnected from the air supply .
RECommENDED oPERATING PRESSURE:
70 to 120 psi / 5 to 8 .5 kgs .
Select the operating air pressure within this range for best fastener performance .
Accessories
STANDARD ACCESSORIES
1 Eye Protection
①
Interchange Brands
1
Operator’s Manual
5
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
Safety Information
Important Safety Instructions for
Operating Nailers
READ ALL INSTRUCTIONS
1 .
OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY
GLASSES WITH SIDE SHIELDS.
Danger to the eyes exists due to the possibility of flying fasteners and debris when operating the nailer . To guard against these hazards always wear safety glasses with side shields to protect both the front and sides . Make sure others in the work area wear safety glasses, too .
Eye protection equipment must conform to the requirements of
American National Standards Institute, ANSI Z87 .1 .
The employer is responsible to enforce the use of eye protection equipment by the tool operator and other personnel in the work area .
2 .
EAR AND HEAD PROTECTION MAY BE NEEDED IN SOME
ENVIRONMENTS.
Some work areas may include exposure to high noise levels which can lead to hearing damage . Always wear ear protection to protect your ears from loud noise . Wear head protection to protect your head from flying objects .
3 .
KEEP FACE, HANDS AND FEET AWAY FROM FIRING HEAD
AT ALL TIMES.
Never place your face, hands or feet near the firing head .
4 .
KEEP FINGER AWAY FROM TRIGGER WHEN NOT DRIVING FASTENERS
TO AVOID ACCIDENTAL FIRING.
Always carry the nailer by the handle only . Never carry the nailer with your finger on trigger since you could drive a fastener unintentionally and injure yourself or someone else .
5 .
NEVER POINT NAILER AT YOURSELF OR OTHERS IN WORK AREA.
Respect the nailer as a working implement . Always assume the nailer contains fasteners and never point the nailer at yourself or others, whether or not it contains fasteners . If fasteners are mistakenly driven, it can lead to severe injuries . Never engage in horseplay with the nailer .
6 .
DRESS PROPERLY.
Do not wear loose clothing or jewelry as they can be caught in moving parts .
Rubber gloves and nonskid footwear are recommended when working outdoors .
Wear protective hair covering to contain long hair .
7 .
KEEP VISITORS AWAY.
All visitors should be kept safely away from work area and should not handle the nailer .
8 .
KEEP OUT OF REACH OF CHILDREN.
9 .
DO NOT OVERREACH.
Keep proper footing and balance at all times .
6
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
10 .
STAY ALERT.
Watch what you are doing . Use common sense and do not operate the nailer when you are tired . The nailer should never be used if you are under the influence of alcohol, drugs or medication that makes you drowsy .
11 .
KEEP WORK AREA CLEAN.
Cluttered areas invite injuries . Clear all work areas of unnecessary tools, debris, etc .
12 .
DO NOT USE THE NAILER AS A HAMMER.
13 .
NEVER CARRY THE NAILER BY THE HOSE.
14 .
HANDLE THE NAILER CAREFULLY.
This nailer was designed for driving nails into wood and similar items . Operate the nailer safely and correctly and do not use for purposes other than those specified in this manual .
Because of high air pressure in the nailer, cracks in the surface are dangerous .
To avoid tool damage, do not drop the nailer or strike the nailer against hard surfaces, and do not scratch or engrave on the nailer . Handle the nailer carefully .
15 .
BEFORE USING THE NAILER, CHECK TO MAKE SURE PARTS ARE NOT
BROKEN OR MISSING AND THAT ALL SCREWS ARE TIGHT. DO NOT
OPERATE A TOOL THAT IS OPERATING ABNORMALLY.
If the nailer appears to be operating unusually, making strange noises, has parts missing or appears to be defective, stop using it immediately and arrange for repairs by an authorized service center .
16 .
BEFORE STARTING WORK, CHECK THE FASTENING OPERATION
SWITCHING DEVICE. (Not available on all tool models.)
If this nailer includes a fastening operation switching device, check the setting of the operation switching device before starting work . If the switching device is not set properly, the nailer will not operate correctly .
17 .
CHECK SAFETY/PUSH LEVER BEFORE USE.
Make sure the safety/push lever operates properly . Never use the nailer unless the safety/push lever is operating properly, otherwise the nailer could drive a fastener unexpectedly . Do not tamper with or remove the safety/push lever, otherwise the safety/push lever becomes inoperable .
18 .
CHOICE OF TRIGGER METHOD IS IMPORTANT.
Read and understand section titled “Methods of Operation .”
(Choice of trigger method is not available on all tool models.)
19 .
DO NOT USE OXYGEN, COMBUSTIBLE OR OTHER BOTTLED GASES.
EXPLOSION MAY OCCUR.
Never use oxygen, combustible gases or any other bottled gases as a power source for the nailer . Use of these gases is dangerous, as the nailer will explode .
Use only clean, dry, regulated compressed air as a power source .
20 .
DO NOT EXCEED 120 psi.
Do not exceed maximum recommended air pressure 120 psi . Never connect the nailer to pressure which potentially exceeds 150 psi as the nailer can burst .
21 .
NEVER USE IN PRESENCE OF FLAMMABLE LIQUIDS OR
COMBUSTIBLES.
The nailer produces sparks during operation . Never use the nailer on sites containing lacquer, paint, benzine, thinner, gasoline, gases, adhesive agents or other materials which are combustible or explosive .
Interchange Brands Operator’s Manual
7
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
22 .
KEEP ALL SCREWS AND COVERS MOUNTED TIGHTLY IN PLACE.
Keep all screws and covers tightly mounted . Check their condition periodically .
Never use the nailer if parts are missing or damaged .
23 .
DO NOT USE THE WRONG FITTING ON NAILER.
The nailer and air hose must have a hose coupler so that all pressure is removed from the nailer when the coupler is disconnected . The connector on the nailer must not hold pressure when the air supply is disconnected . If the wrong fitting is used, the nailer can remain charged with air after disconnecting and thus will be able to drive a nail even after the air line is disconnected, possibly causing injury .
24 .
DO NOT LOAD FASTENERS WITH TRIGGER PULLED OR SAFETY/PUSH
LEVER DEPRESSED.
When loading fasteners into the nailer or when connecting the air hose:
Do not pull the trigger
Do not depress the safety/push lever
Keep the nailer pointed downward
25 .
CHECK FOR LIVE WIRES.
Avoid the risk of severe electrical shock by checking for live electrical wires that may be hidden by walls, floors or ceilings . Turn off the breaker switch to ensure there are no live wires .
26 .
HOSES.
Air hoses should be professional grade and have a minimum of 150 psi working pressure . Make sure that the hose is securely fastened . If there is any damage to the hose, replace it before using the nailer .
27 .
PLACE NAILER PROPERLY ON WORK PIECE.
Do not drive fasteners on top of other fasteners or with the nailer at too steep of an angle . The fasteners can ricochet and hurt someone .
28 .
BE CAREFUL OF DOUBLE FIRING DUE TO RECOIL.
If the safety/push lever is unintentionally allowed to re-contact the work piece following recoil, an unwanted fastener will be driven .
In order to avoid this undesirable double fire:
Intermittent operation ﹙trigger or single firing﹚
(not available on all models)
1﹚ Set the switching device to SINGLE ACTUATION MECHANISM .
2﹚ Pull the trigger rapidly and firmly .
Continuous operation ﹙safety/push lever firing﹚
1﹚ Do not press the nailer against the wood with excessive force .
2﹚ Separate the nailer from the wood as it recoils after fastening .
29 .
DO NOT DRIVE FASTENERS CLOSE TO THE EDGE OR CORNER OF THE
WORK ESPECIALLY WHEN USING THIN MATERIAL.
The work piece is likely to split and the fastener could fly free and hit someone .
30 .
NEVER DRIVE FASTENERS FROM BOTH SIDES OF A WALL AT THE SAME
TIME.
The fasteners could be driven into and through the wall and hit a person on the opposite side .
31 .
DO NOT DISCONNECT AIR HOSE FROM NAILER WHILE FINGER IS ON
THE TRIGGER.
The nailer can fire when it is re-connected to an air supply .
8
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
32 .
DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE
NAILER IS NOT IN USE. NEVER LEAVE A NAILER UNATTENDED WITH
THE HOSE ATTACHED.
Always disconnect the air supply from the nailer and empty the magazine when operation has been completed or suspended, when unattended, moving to a different work area, adjusting, disassembling, or repairing the nailer, and when clearing a jammed fastener .
33 .
DISCONNECT AIR HOSE FROM NAILER WHEN:
Doing maintenance and inspection
Loading fasteners
Clearing a jam
It is not in use
Leaving work area
Moving it to another location
Handing it to another person
34 .
MAINTAIN NAILER WITH CARE.
Keep the nailer clean and lubricated for better and safer performance .
35 .
USE ONLY AUTHORIZED OR RECOMMENDED PARTS, ACCESSORIES OR
FASTENERS.
Unauthorized parts, accessories or fasteners may void your warranty and can lead to tool malfunction and resulting injuries . Only authorized service personnel should repair the nailer .
36 .
NEVER MODIFY OR ALTER A NAILER.
Doing so may cause it to malfunction and personal injuries may result . The warranty is no longer valid when a tool is modified or altered .
37 .
BE CAREFUL WHEN CLEANING TOOL WITH A BLOW GUN.
Do not touch the trigger, point the air outlet at a person, touch the safety/push lever, or set it to pushed up status .
38 .
STORE NAILER PROPERLY.
When not in use, the nailer should be stored in a dry place . Keep out of reach of children and lock the storage area .
Employer’s Responsibilities
1 .
Ensure that this manual is available to operators and personnel performing maintenance .
2 .
Ensure that nailers are used only when operators and others in work area are wearing EYE PROTECTION .
3 .
Keep nailer in safe working order .
4 .
Maintain nailer properly .
5 .
Ensure that the nailers that require repair are not used before the repair is completed .
Interchange Brands Operator’s Manual
9
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
operating the Nailer
NOtE:
The information contained in this Manual is designed to assist you in the safe operation of the nailer . Some illustrations in this Manual may show details or attachments that are different from those on your nailer .
Air Supply, Connections and Operating Pressure
Read section titled SAFETY. Make sure of the following before operation:
Air Supply
Power Source (Compressor)
Use only clean, dry, regulated compressed air as a power source for this nailer .
NEVER use oxygen or other bottled gases, as an explosion may occur .
Air compressors used to supply compressed air to this nailer must comply with the requirements of the latest version of ANSI Standard
B 19 .3 Safety Standard for Compressors for Process Industries .
Moisture or oil in the air compressor may accelerate wear and corrosion in the nailer .
Drain daily .
Connections
1 .
Fittings
Install a female coupler to the hose . The female coupler will connect to the quick release that fits the tool .
2 .
Filter-Regulator-Lubricator
NEVER connect nailer to pressure which potentially exceeds 150 psi .
Filter-regulator-lubricator units supply an optimum condition for the nailer and extend the nailer life . These units should always be used .
Filter
The filter removes moisture and dirt mixed in compressed air .
Keep the filter clean by maintaining tool regularly .
Drain daily .
Regulator
The regulator controls the operating pressure for safe operation of the nailer .
Inspect the regulator before operation to be sure it operates properly .
Lubricator
The lubricator supplies an oil mist to the nailer .
Inspect the lubricator before operation to be sure the supply of lubricant is adequate .
If an inline lubricator is not used, a few drops of oil will need to be added to the air inlet before each use .
10
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
3 .
Air Hose
Air hose must have a minimum working pressure rating of 150 psi or 150% of the maximum pressure produced in the system, whichever is higher .
Operating Pressure
Recommended operating pressure range is 70 to 120 psi / 5 to 8 .5 kgs .
Maximum permissible operating pressure is 150 psi .
Select the operating pressure within this range for the best fastener performance . The nail length and thickness and the hardness of the wood are factors in determining what the pressure should be set at .
Do not exceed this recommended operating pressure .
Lubrication
It is important that the tool be properly lubricated . Without proper lubrication, the tool will not work properly and parts will wear prematurely .
Use INTERCHANGE pneumatic tool lubricant . Do not use detergent oil or additives . These lubricants will harm the O-rings and other rubber parts . This will cause the tool to malfunction .
Filter-regulator-lubricator units should always be used . Keep the lubricator filled with INTERCHANGE pneumatic tool lubricant .
If a lubricator is not available, supply 3 to 5 drops of INTERCHANGE pneumatic tool lubricant into the air plug on the tool twice a day .
NOtE:
Dirt and water in the air supply are major causes of wear in the tool . An air filter will help to get the best performance and minimum wear from the tool .
Frequent, but not excessive, lubrication is required for the best performance . Oil added through the air line connection will lubricate the internal parts .
Interchange Brands
WARNING
NEVER connect nailer to pressure which potentially exceeds 150 psi.
DO NOT USE THE WRONG FITTING ON NAILER.
The nailer and air hose must have a hose coupler so that all pressure is removed from the nailer when the coupler is disconnected . The connector on the tool must not hold pressure when the air supply is disconnected . If the wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a nail even after the air line is disconnected, possibly causing injury .
DANGER
NEVER use oxygen or other bottled gases, as an explosion may occur.
Operator’s Manual
11
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
operating The Nailer
DANGER:
Operators and others in work area must wear safety glasses with side shields that conform to ANSI Z87 .1 specifications .
Read and understand METHODS OF OPERATION .
Operating Instructions
Read section titled “SAFETY INSTRUCTIONS .”
BEFoRE oPERATIoN
1 .
Wear safety glasses or goggles with side shields .
2 .
Do not connect the air supply .
3 .
Inspect screws and tighten if necessary .
4 .
Check operation of the contact arm and trigger to make sure they are moving smoothly .
5 .
Connect the air supply .
6 .
Check the air-leakage .
(The tool must not have any air-leakage.)
7 .
Hold the tool with finger off the trigger, then push the contact arm against the work piece .
(The tool must not operate).
8 .
Hold the tool with contact arm away from work piece and pull the trigger .
(The tool must not operate.)
9 .
Disconnect the air supply .
oPERATIoN
Danger to the eyes exists due to the possibility of flying fasteners and debris when operating the nailer . To guard against these hazards always wear safety glasses with side shields to protect both the front and sides . Make sure others in the work area wear safety glasses, too .
Eye protection equipment must conform to the requirements of American National
Standards Institute, ANSI Z87 .1 .
The employer and/or user must ensure that proper eye protection is worn . Eye protection equipment must conform to the requirements of the American National
Standards Institute, ANSI Z87 .1 and provide both frontal and side protection .
The employer is responsible to enforce the use of eye protection equipment by the tool operator and all other personnel in the work area .
NOtE:
Spectacles and face shields without the side shields do not provide adequate protection .
Keep hands and body away from the discharge outlet when driving the fasteners to prevent striking the hands or body by mistake .
12
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Nail Loading
Model No. CN55-15
Item No. 65530
1 .
OPEN THE MAGAZINE
Hold door and door latch and pull up door latch . Swing door open .
Swing magazine cover open .
2 .
CHECK ADJUSTMENT
The nail support can be moved up and down to four settings . To change setting pull up on the post and twist to the correct step . The nail support should be adjusted correctly to the position indicated in inches and millimeters inside magazine .
3 .
NAIL LOADING
Place a coil of nails over the post in the magazine . Uncoil enough nails to reach the feed pawl and place the second nail between the teeth on the feed pawl . The nail heads fit in slot on nose .
4 .
SWING COVER CLOSED
5 .
CLOSE THE DOOR
Check that the latch engages . ﹙If it does not engage, check that the nail heads are in the slot on the nose﹚ .
Interchange Brands Operator’s Manual
13
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Testing The Nailer
Model No. CN55-15
Item No. 65530
Before using the nailer, test it by using the check list below .
If abnormal tests occur, stop using the nailer and contact an authorized service center immediately .
Conduct the test in the following order .
1 .
Adjust the air pressure to 70 psi and connect the air hose .
2 .
Without touching the trigger, depress the contact arm against the work piece . Pull the trigger . ﹙The tool must fire the fastener .﹚
3 .
With the tool off the work piece, pull the trigger . Depress the contact arm against the work piece . ﹙The tool must fire the fastener .﹚
4 .
Adjust the air pressure to the lowest setting possible according to the diameters and length of fastener and the hardness of work piece .
Methods of Operation
Explanation of the nailing operation
■
Bump Fire (multi-Fire)
Pull the trigger with the nailer off the workpiece .
Depress the push lever against the workpiece to drive a nail .
Move the nailer along the workpiece with a bouncing motion .
Each depression of the push lever will drive a nail .
As soon as the desired number of nails have been driven, remove finger from the trigger .
Trigger
WARNING!
■
Always follow the tool manufacturer’s safety and maintenance instructions .
■
Always wear safety glasses with side shields when operating or servicing tools .
■
Always disconnect the air supply from the tool and empty the magazine when servicing tools .
14
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Driving Depth Adjustment Dial
(on some models)
WARNING:
Always disconnect air supply before changing the adjustment dial .
■
With air pressure set, drive nails into a piece of scrap material to determine if an adjustment is necessary .
■
If adjustment is required, disconnect air supply .
■
Refer to the mark on the contact arm for direction to turn the adjustment dial .
■
Reconnect air supply .
Directional Exhaust Cover
(on some models)
WARNING:
Always disconnect air supply before rotating the exhaust cover .
■
Rotate Cover by Unscrewing
Loosen screw as shown . Adjust to desired exhaust direction and tighten screw .
■
Rotate Cover by Hand
Direction of the exhaust air can be changed by rotating exhaust cover by hand .
Model No. CN55-15
Item No. 65530
Troubleshooting
Problem Cause
Trigger valve leaks air O-ring is cut or cracked
Solution
Replace o-ring
Nose leaks air
Failure to cycle
O-ring or gasket is cut or cracked Replace o-ring or gasket
Bumper is cracked or worn Replace bumper
Air supply restriction
Tool is dry, lack of lubrication
Cap malfunction
Check air supply equipment
Apply air tool lubricant
Replace cap
Lack of power
Slow to cycle
Air pressure is too low
Cap malfunction
O-ring or seal is cut or cracked
Tool is dry, lack of lubrication
Nails jam in tool Bent nails
Broken or chipped driver
Wrong size nail
Check air supply equipment
Replace cap
Replace o-ring or seal
Apply air tool lubricant
Replace with new nails
Replace piston/driver assembly/bumper
Replace with correct type of nail
Interchange Brands Operator’s Manual
15
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
maintenance and Inspection
Read the section titled SAFETY.
SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use . It is recommended that these operations should be performed by a professional technician .
NOtE:
The information contained in this Manual is designed to assist you in the safe maintenance of the nailer . Some illustrations in this Manual may show details or attachments that are different from those on your nailer .
WARNING:
Disconnect air hose and remove nails from nailer when:
Doing maintenance and inspection Clearing a jam
Inspecting the magazine
1 . DISCONNECT AIR HOSE .
2 . Clean the magazine . Remove dust which may have accumulated in the magazine .
3 . Lubricate the nail rail with nailer lubricant .
Clearing a jam
Remove a jammed nail in the following order:
1 . DISCONNECT AIR HOSE .
2 . Remove all nails .
3 . Remove the jammed nail with a slotted head screwdriver .
4 . In case of frequent jams, contact an authorized service center .
A qualified person should perform repairs and maintenance.
Periodic maintenance to be performed:
Check that the piston bumper is operating normally . A damaged piston bumper may cause damages to other component parts .
Check o-rings for wear or damage . Damaged o-rings may affect overall performance .
Make sure all screws are secure . Loose screws may affect overall performance .
When repairing a tool, make sure the internal parts are clean and lubricated .
Storing
When not in use for an extended period, apply a thin coat of the lubricant to the steel parts to avoid rust .
Cold Weather Care
Do not store the tool in a cold weather environment .
Keep the tool in a warm area until beginning the work .
If the tool is already cold, bring it in a warm area and allow the tool to warm up before use .
1 . Reduce the air pressure to 60 to 80 psi ﹙4 .2 bar 4 .2 kgf/cm2﹚ .
2 . Remove all fasteners from the tool .
3 . Connect the air hose and free-fire ﹙blank-fire﹚ the tool .
The lowered air pressure will be enough to free-fire the tool . Slow speed operation tends to warm up the moving part .
16
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
Parts Drawing/Schematics, Parts List & Parts Kits
PARTS DRAWING/SCHEmATICS FoR CN55-15
Interchange Brands Operator’s Manual
17
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
Model No. CN55-15
Item No. 65530
NO.
1
8
9
6
7
4
5
2
3
ORDER NO. DESCRIPTION
610560
320750
610220
630070
511030
310300
520130
510680
110320
510670
410210
420160
620600
210410
321400
210400
610210
210350
420170
420180
110290
520310
320460
410230
620010
510570
510700
310170
410220
######
######
510510
310310
321410
######
420780
321300
321290
620640
610330
610240
210390
640340
620610
320210
321390
510320
510430
620120
620130
320280
38
39
40
41
34
35
36
37
30
31
32
33
26
27
28
29
46
47
48
49
42
43
44
45
50
51
22
23
24
25
18
19
20
21
14
15
16
17
10
11
12
13
BOLT M6X20 (Loctite 243) 52
EXHAUST COVER
BOLT M6X25
SPRING WASHER
CYLINDER CAP
GASKET
RING
PISTON STOP
COMPRESSION SPRING
O-RING 41.2X3.55
O-RING 53X2.65
HEAD VALVE PISTON
CYLINDER SEALING RING
NOT APPLICABLE
NOT APPLICABLE
O-RING 37.5X3.55
PISTON
DRIVER BLADE (Loctite 262) 69
NOT APPLICABLE
CYLINDER RING
O-RING 73X2.65
CYLINDER
CYLINDER SEAL
70
71
O-RING 50X2.65
BODY
O-RING 50X1.8
BUMPER
PIN CAP (B)
CHECK PAWL SPRING
CHECK PAWL
CHECK PAWL PIN
NO.
DOOR
BOLT M6X22 (Loctite 243) 85
NOSE
PIN CAP (A)
GUARD COVER
DOOR PIN
SAFETY
SAFETY SPRING
NUT M6 (Nylock)
BOLT M6X35
FEED PAWL
ROLL PIN 3X16
FEED SPRING
FEED PAWL PIN
FEED PISTON
O-RING 10X2.65
O-RING 20X2.65
FEED PISTON SPRING (A)
FEED PISTON SPRING (B)
SPRING GUIDE
80
81
83
84
94
95
96
97
99
100
101
102
P1
P2
90
91
92
93
86
87
88
89
65
66
67
68
61
62
63
64
57
58
59
60
53
54
55
56
76
77
78
79
72
73
74
75
PARTS LIST FoR CN55-15
420520
421580
321380
630220
######
######
410880
323140
510280
323180
321540
324520
D321411
T420091
510180
640250
420090
510410
510380
610200
630110
420540
110310
410430
321420
420870
420240
420860
420850
620650
210700
510090
######
320570
322730
320560
640340
640180
410140
420080
320110
510030
620050
510240
330010
510210
ORDER NO. DESCRIPTION
410440
320590
630050
640080
620240
FEED PISTON BUMPER
FEED PISTON CAP
SNAP RING
ROLL PIN 3X12
LATCH SPRING
LATCH
O-RING 4X1.5
Replaced by #96 #97
TRIGGER
SAFETY BRACKET
CONTACT PLATE
ROLL PIN 3X16
ROLL PIN 3X30
HANDLE GRIP
TRIGGER VALVE CAP
TRIGGER STEM
O-RING 2.5X1.4
TRIGGER VALVE SPRING
O-RING 8.6X1.9
TRIGGER VALVE BUSHING
O-RING 6.3X1.8
O-RING 5.8X1.9
STRAIGHT PIN B3X15
TRIGGER VALVE CAGE
O-RING 18.3X2.65
O-RING 16X1.8
BOLT M6X20
SNAP RING
FILTER
END CAP
PLASTIC WASHER
MAGAZINE PIN
MAGAZINE
SPRING HOLDER (B)
MAGAZINE POST
NAIL SUPPORT PLATE
MAGAZINE SPRING
SPRING HOLDER (A)
MAGAZINE COVER
SIDE PROTECTOR
SNAP RING
NOT APPLICABLE
NOT APPLICABLE
STRAIGHT PIN CAP
STRAIGHT PIN
O-RING 9X2
WASHER
SPRING SEAT
SLEEVE
DRIVER UNIT
TRIGGER VALVE
18
Interchange Brands Operator’s Manual
15 o
Coil Nailer
Drives Wire Collated Nails (1-1/4" to 2-1/4" / 32 to 57mm)
PARTS KITS FoR CN55-15
Model No. CN55-15
Item No. 65530
ORDER NO.
DESC. CODE KIT #
98460
98465
98470
98475
98480
98485
98486
98487
98488
CN55K1
CN55K2
CN55K3
CN55K4
CN55K5
CN55K6
CN55K7
CN55K8
CN55K9
Kit #1
Kit #2
Kit #3
Kit #4
Kit #5
Kit #6
Kit #7
Kit #8
Kit #9
ITEM
O-Ring/Gasket Kit for CN55-15
Piston/Driver Assembly for CN55-15
Head Cap Assembly for CN55-15
Trigger Valve Assembly with Trigger for CN55-15
Magazine Assembly for CN55-15
Guide Body Assembly for CN55-15
Safety Kit for CN55-15
Feeder Kit for CN55-15
Bumper Kit for CN55-15
NOtICE:
The parts listed in this manual are for service assembly and for reference .
Changes to the tool and drawing may be made without notification .
Most parts or parts kits are available . Contact your local dealer for more information .
WARNING:
When the tool needs repairing or servicing, it is strongly recommended that you contact your local dealer . Do not disassemble the tool yourself, which might waive your right for product guarantee .
Interchange Brands
WARNING!
■
Always follow the tool manufacturer’s safety and maintenance instructions .
■
Always wear safety glasses with side shields when operating or servicing tools .
■
Always disconnect the air supply from the tool and empty the magazine when servicing tools .
Operator’s Manual
19
Limited Five (5) Year Warranty for
Pneumatic Nailers
Our products are designed and constructed using the highest standards of both material and workmanship. We warrant to the original retail purchaser that their nailers will be free from defects in material or workmanship for the warranty period of five years.
During the warranty period (which begins on the purchase date), we will repair or replace, at our option and expense, any product or part that is defective in materials or workmanship after examination by an Authorized Warranty Service Center, subject to the exceptions, exclusions and limitations described below. Any replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced product or part. A DATED SALES RECEIPT OR PROOF OF PURCHASE FROM THE
ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A WARRANTY CLAIM. To make a warranty claim, you must return the product, with proper receipt/proof of purchase and return transportation charges prepaid, to us (your dealer) or an Authorized Warranty
Service Center. We will perform our obligations under this warranty within a reasonable time after approval of the warranty claim.
WARRANTY EXCLUSIONS
The following warranty exclusions apply:
1. Normal wear parts are not covered under this warranty. Normal wear parts include, for example, rubber o-rings, seals and driver blades.
2. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, accidents, operation at other than recommended speeds, improper storage, or damage resulting during shipping.
3. Products used in production/industrial applications are excluded from this warranty.
4. Labor charges, maintenance, or loss, damage and repairs resulting from improper operation are not covered by this warranty.
GENERAL WARRANTY CONDITIONS
This warranty will be honored, only if:
1. Clean, dry, regulated compressed air has been used at air pressure not exceeding the maximum indicated on the tool casting;
2. No evidence of abuse, abnormal conditions, accident, neglect, misuse or improper modifications or storage of the product exists; and
3. No deviations from following recommended operating instructions, specifications, and maintenance schedules exist. (Read Operator Manual for use, specifications, and maintenance instructions).
This warranty is the only warranty for the product and we disclaim all other warranties. Any implied warranties will be limited in duration to the applicable warranty period specified above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Your remedies are solely and exclusively as stated above. We shall in no event be liable for incidental, consequential, indirect or special damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. In no event, whether as a result of a breach of contract, warranty, tort (including negligence) or otherwise, shall our liability exceed the price of the product that has given rise to the claim or liability. Any liability connected with the use of this product shall terminate upon the expiration of the warranty period specified above. No employee or representative of any distributor or dealer is authorized to make any change or modification to this warranty.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Interchange Brands CN55-15
Operator’s Manual (08/06/15)
CN55-15 Coil Nailer
Made In China
DB
Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Drives wire collated nails from 1 1/4" to 2 1/4"
- Lightweight and ergonomic design for easy handling
- Adjustable depth of drive for precise nailing
- Safety features for added protection
- Durable construction for long-lasting performance
- Easy to load magazine with a capacity of 250 to 400 nails
