UNIVERSAL EDGE GUIDE

UNIVERSAL EDGE GUIDE
Item #: 53970
UNIVERSAL EDGE GUIDE
When using the EZ SMART Universal Edge Guide with any power tool, be sure you have read and understand
the operating manual for the tool before operation. Be sure to use the tool safely. Do not disable any built-in
safety features. Be sure to follow safe practices when using the EZ SMART Universal Edge Guide with your
power tools. If a task seems like it might be potentially unsafe, do not attempt. Do not operate any tool with
the EZ SMART Universal Edge Guide if you are tired or distracted in any way.
The EZ SMART Universal Edge Guide (UEG) turns your
circular saw into a versatile cutting tool that can handle
ripping procedures in a variety of materials, including
dimensional lumber and large panels. The UEG can be used
on vertical or horizontal workpieces. The EZ SMART Saw
Base ensures safe, accurate, and chip-free cuts.
Parts
Frame
(2) Arms with measurements
(1) 24” Fence
Handle Assembly
(1) Tubular handle
(2) Black handle caps
(2) T-nuts
(2) 3/4” screws
(2) Washers
Fence Hardware
(2) Pre-tapped EZ Connectors
(4) 5/8” screws
(4) Washers
(2) Locking hex nuts
Smart Base Assembly*
(2) Studded EZ Connectors
(4) Knobs
(4) Washers
(1) Smart Saw Base
(1) Off-Rail Insert
(2) On-Rail Inserts (Left and Right)
(1) Fin Insert with (1) Fin
* Smart Base Assembly is an optional component
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 1
Phone (877) 681-7955 Fax (352) 620-2576
techsupport@eurekazone.com
www.eurekazone.com
v14-01
ASSEMBLING THE FRAME
Step 1
Insert a 5/8” screw into the third
hole from end of the Arm. The
washer is placed between the
screw and the Arm. Repeat for the
other Arm. Slide Fence over the
connectors. Do not fully tighten
the screws at this time.
Step 2
Line up the second hole in the Arm
to the hole in the lip of the Fence.
Insert screw and washer as shown
at right. Repeat for the other Arm.
Do not fully tighten the screws at
this time.
Step 3
Square the Arm to the Fence and
tighten the screws. Minor
adjustments may be needed as the
Handle and the Smart Saw Base
are attached. The completed
frame at this point is shown at the
right.
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 2
Phone (877) 681-7955 Fax (352) 620-2576
techsupport@eurekazone.com
www.eurekazone.com
v14-01
ATTACHING THE HANDLE
Insert the T-nut through the hole
in the Handle. Insert the screw
with the washer through the first
hole of the Arm, as shown, and
into the end of the T-nut. Before
fully tightening the screw, place
the black end cap over the end of
the Handle. Verify that the UEG
frame is square, then tighten the
screws.
ATTACHING THE SMART BASE
Slide studded EZ connectors into
Arms. Place EZ SMART Saw Base
on to studs as shown at right.
Secure with washers and knobs.
Note: The Saw Base can be used to
ensure that the UEG frame is
square.
USING THE MARKS
The embossed marks on the EZ SMART Saw Base are used to line up the saw to the desired measurement on
the UEG Arms. The embossed marks correspond to the inside edge of the saw blade.
Example:
Cut set for 22”
FRONT EDGE OF SAW BASE
BACK EDGE OF SAW BASE
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 3
Phone (877) 681-7955 Fax (352) 620-2576
techsupport@eurekazone.com
www.eurekazone.com
v14-01
USING THE UEG
CAPACITY:
●
●
●
0-24” width of cut (markings for 0-24” on arms); unlimited workpiece length
Keep Fence against the workpiece. Apply pressure using the Handle as the UEG is moved along the
workpiece
The long Fence can compensate for irregularities of the edge of the workpiece
The examples below show the workpiece laying in the horizontal position, but the UEG can also be used
with the workpiece in the vertical position.
Narrow Stock
Rip along the length of dimensional
lumber or other long stock
Rip narrow strips
material
Thinfrom
Strips
Rip thin strips for larger stock
Straight-Line Rip
Rip irregular boards using a straight
edge
Wide Boards
Cut down large panels
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 4
Phone (877) 681-7955 Fax (352) 620-2576
techsupport@eurekazone.com
www.eurekazone.com
v14-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising