Maven Series - eDigitalDeals

Maven Series - eDigitalDeals
Network Camera
Maven Series
User
Manual
201407 A2
Table of Contents
1
Network Deployment
Network Topology
4
1.2
Connection
5
1.2.1 Checking Appearance
5
1.2.2 Default IP address
5
1.2.3 Connecting from a computer & Viewing Preparation
5
IP Finder
9
1.3
2
4
1.1
Administration and Configuration
2.1
2.2
10
Live View
10
2.1.1 Model Reference Table
12
Configuration
13
2.2.1 Information
13
2.2.2 Image Parameter
13
2.2.3 Network Settings
20
2.2.4 Account Management
24
2.2.5 Event Settings
25
2.2.6 Record Settings
28
2.2.7 System Settings
30
2.2.8 Event Log
32
Appendix A: Specifications of Indoor Dome Network Camera (Manual Focus Model)
33
Appendix B: Specifications of Indoor Dome Network Camera (Motorized Lens Model)
35
Appendix C: Specifications of Outdoor IR Dome Network Camera
37
Appendix D: Specifications of Fixed Network Camera
39
Appendix E: Specifications of IR Bullet Network Camera
41
Appendix F: Specifications of Flat Mini Dome Network Camera
43
1
WARNING
●● The unit operates at DC 12V/AC 24V/ PoE (for Indoor Dome Network Camera & Fixed Network Camera), AC 24V/ PoE (for
Outdoor IR Dome Network Camera & IR Bullet Network Camera).
●● Installation and service should be performed only by qualified and experienced technicians and comply with all local
codes and rules to maintain your warranty.
●● To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.
●● Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry
soft cloth.
●● Do not apply benzene or thinner to the camera, which may cause the surface of unit to be melted or lens fogged.
●● Avoid aligning the lens to very bright objects (example, light fixtures) for long periods of time.
●● Avoid operating or storing the unit in the following locations:
• Extremely humid, dusty, or hot/cold environments [ Recommended operating temperature: -10°C to +50°C, (for Indoor
Dome Network Camera & Fixed Network Camera), -40°C to +50°C (for Outdoor IR Dome Network Camera & IR Bullet
Network Camera)]
• Close to sources of powerful radio or TV transmitters
• Close to fluorescent lamps or objects with reflections
• Under unstable or flickering light sources
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the
European Union and other European countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.
Get Started
This user manual is designed as a reference for the installation and manipulations of the unit including the camera’s features,
functions, and detailed explanation of the menu tree. Please read this manual thoroughly and save it for future use before
attempting to connect or operate the unit. The reader is supposed to be able to get the following information in this manual.
●● Product Overview: the main functions and system requirements of the unit.
●● Installation and Connection: instructions on unit installation and wire connections.
●● Administration and Configuration: the main menu navigation and controls explanations.
2
FCC Compliance Statement
Information to the user: This unit has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this unit does cause harmful interference to radio or television reception, which can be determined by turning the unit off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
●●
●●
●●
●●
Reorient or relocate the receiving antenna.
Increase the separation between the unit and receiver.
Connect the unit to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the unit.
CE Statement
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation. The manufacturer declares that the unit supplied with this guide is compliant with the essential
protection requirements of EMC directive and General Product Safety Directive GPSD conforming to
requirements of standards EN55022 for emission, EN 55024 for immunity, EN 300 and EN 328 for WIFI.
3
1
Network Deployment
1.1
Network Topology
The unit, which is equipped with Ethernet RJ-45 network interface, can deliver video images and audio in real time via either
Internet or Intranet. Please refer to the skeleton drawings shown below for understanding. (Here takes Indoor Dome Network
Camera as the example in the illustration.)
Figure 1 - 1: Network Topology Type 1
Figure 1 - 2: Network Topology Type 2
4
1.2
Connection
1.2.1 Checking Appearance
Below table lists the minimum requirement to implement and operate the unit. No hardware/software component inferior to
the requirements is recommended.
Table 1 - 1: System Requirements
System Hardware
CPU
RAM
Display
System Software
Operating System
Browser
Unit
Power Supply
Networking
Wired**
Intel Pentium 4 2.4GHz or equivalent
1 GB or above
NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500
Microsoft Windows XP, Windows Vista, or Windows 7
Microsoft Internet Explorer 8 or above, Chrome, Firefox
DC 12V / AC 24V / PoE(for Indoor Dome Network Camera & Fixed Network Camera)
AC 24V/ PoE (for Outdoor IR Dome Network Camera & IR Bullet Network Camera)
10/100BASE-T Ethernet (RJ-45 connector)
*a switch is required for surveillance on multiple units.
Note
All the installation and operations should comply with your local electricity safety rules.
Caution
To avoid damage to the unit, never connect more than one type of power supply (PoE IEEE802.3
Ethernet Class 0, DC 12V / AC 24V or AC24V power plug) at the same time. If using PoE, this unit must be
connecting only to PoE networks without routing to heterogeneous devices.
1.2.2 Default IP address
Since this is a network-based unit, an IP address must be assigned at the very first. The unit’s default IP address is
192.168.1.30 and sub mask is 255.255.255.0. However, if you have a DHCP server in your network, the unit would obtain
an IP address automatically from the DHCP server so that you don’t need to change the camera’s IP address. But be sure to
enable DHCP in "Network Settings".
1.2.3 Connecting from a computer & Viewing Preparation
Connecting from a computer
1.
2.
3.
Make sure the unit and your computer are in the same subnet.
Check whether if the networking available between the unit and the computer by executing ping the default
IP address. To do this, simply start a command prompt (Windows: from the Start Menu, select Program.
Then select Accessories and choose Command Prompt.), and type “Ping 192.168.1.30”. If the message
“Reply from…” appears, it means the connection is available.
Start Internet Explorer and enter IP address: 192.168.1.30. A login window should pop up. In the window,
enter the default user name: admin and password: 1234 to log in.
Further administration on the unit can be found in “2. Administration and Configuration".
5
Figure 1 - 3: Login Window
Viewing Preparation
Images of the unit can be viewed through Microsoft Internet Explorer 8 or above. Before viewing, follow these steps to
enable the display.
1. Enable Cookies as instructions below
 In Internet Explorer, click Internet Options on the Tools menu.
 On the Privacy tab, move the settings slider to Low or Accept All Cookies.
 Click OK.
2. When a proxy server is used, click Internet Options on the Tools menus of Internet Explorer, select Connect
tab, click LAN button, and set proxy server.
3. Change Security in Internet options as instructions below
 On tool menu, click Internet Option.
 Press the Security tab.
 If the camera operates inside of the intranet, click the Intranet icon.
 If the camera operates outside of the intranet, click the Internet icon.
 Click Custom Level. This will open the Security Settings – Internet Zone screen.
Figure 1 - 4: Security Settings 1/4
6

Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:
【Download signed ActiveX controls】 Prompt (recommended)
【Download unsigned ActiveX controls】 Prompt
【Initialize and script ActiveX not marked as safe for scripting】 Prompt
Figure 1 - 5: Security Settings 2/4
【Automatic prompting for ActiveX controls】Enable
Figure 1 - 6: Security Settings 3/4
7
【Run ActiveX controls and plug-ins】 Enable
【Script ActiveX controls marked safe for scripting*】Enable
Figure 1 - 7: Security Settings 4/4




Press OK to save the settings.
Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking effect.
Type your setting IP address into the browser.
Then you should be able to see the camera image screen.
8
1.3
IP Finder
IP Finder is a utility program that helps users locate the unit in the local area network which the computer is connected to.
Please note that IP Finder works only on Microsoft Windows XP, Microsoft Windows Vista, and Microsoft Windows 7. Steps to
get the utility program running are listed below.
1.
2.
3
4.
5.
Download IP Finder from MESSOA Website to the computer.
Double click on IPFinder.exe in the IP Finder folder, and the IP Finder window should pop out.
The window would list information of units in operation at present. Press FIND CAMERA to find more units.
Locate and double-click one of the cameras in the list you want to configure the network settings. If you have multiple
cameras connected to your local network, locate the MAC address on the camera to distinguish the target camera from
others.
Configure the following settings as needed.
• NAME: Enter a descriptive name for the camera.
•
NETWORK SETTINGS: If you have a DHCP server on your network to assign IP addresses to network devices, enable the
DHCP option. Otherwise, manually enter the IP ADDRESS, NET MASK and GATEWAY values.
•
USERNAME & PASSWORD: Manually setup preferred username and password.
•
SET: Whenever you make revision of camera settings, click “SET” to take effect.
•
SW DEFAULT: To perform the factory defaults excluding network settings of the selected camera.
•
HW DEFAULT: To perform the factory defaults of the selected camera.
•
RESET: To reboot the selected camera.
Click Save to enable the settings and click Exit to exit the utility.
Figure 1 - 8: IP Camera Finder
9
2
Administration and Configuration
2.1
Live View
Figure 2 - 1: First Login Page
After accessing and login to the IP address of the unit, the screen will be shown as the above screenshot. There are 2 main
options on the upper left side: “Live View” and “Configuration”. While the upper right side indicates your current login user
level with “Logout” option which enables you to log out after pressing. We mainly focus on “Live View” functionalities in this
chapter and will detail “Configuration” in the “2.2 Configuration” later.
Figure 2 - 2: Live View
After clicking “Live View”, you will be led to real-time live view screen, the left dropdown menu is for user interface language
changing and the “Stream” lets users toggle among each stream settings for better adaptation in different network
condition, for which you may refer to “Edit Profiles & Streams” for more details.
The following icons within the table, which are on the top of live view screen, are for some functions activating and alarm
warning status. Please refer to the detailed definitions below for more understanding (Flat Mini Dome Series have some
differences with other network cameras).
10
Icon
Definition
The “Snapshot” button is for taking a snapshot saved in a user-preferred file path.
The “Fixed” button is for users to display a fixed size live view screen.
The “Real” button is for users to display a real size streaming live view screen.
The “Full Screen” button is for users to display a full screen live view display. (Press Esc to back)
The “Audio Input” button is for users to toggle on/off the audio input function.
(1M Flat Mini Dome Network Camera Excluding)
The “Audio Output” button is for users to toggle on/off the audio output function.
(1M Flat Mini Dome Network Camera Excluding)
The vibration-like icon indicates motion(s) being detected in camera coverage.
The siren-like icon indicates that alarm input event is triggered.
(1M/3M Flat Mini Dome Network Camera Excluding)
Table 2 - 1: Live View Icon Definition
Figure 2 - 3: Live View Right-Clicking Controls
Right clicking on the live view screen can pop up more functions to select.
●● Version
Click to view the version details.
●● Full screen
Click to display a full screen live view display. (Press Esc to back)
●● Start Record
Click to record the live view into video file at a preferred file path.
Note
Keep the zoom level of IE as 100% to display normal live view.
11
2.1.1 Model Reference Table
Below table tells the model differences that can be seen on the home page. “√” indicates functions which can be found on
the model. “A-F” each indicates a model type, “a-d” indicates different lens as shown below:
A. 1MP/3MP/5MP Indoor Dome Network Camera
B. 3MP/5MP Outdoor IR Dome Network Camera
C. 3MP/5MP Fixed Network Camera
D. 3MP/5MP IR Bullet Network Camera
E. 1MP Flat Mini Dome Network Camera
F. 3MP Flat Mini Dome Network Camera
(*) a. Manual Focus Lens; b. Motorized Lens; c. CS Mount; d. Fixed Focal Lens
Function
Model
Snapshot
Motion Detection
Alarm I/O
Edge Recording
Audio
Remote Lens Zoom Control
Control
Focus Control
Power
DC 12V
Requirement AC 24V
PoE
Operating
-10ºC ~ 50ºC
Temperature
(-14ºF ~ 122ºF)
-40ºC ~ 50ºC
(-40ºF ~ 122ºF)
Defrost
a
√
√
√
√
√
√
√
√
√
A
b
√
√
√
√
√
√
√
√
√
√
√
a
√
√
√
√
√
√
√
-
B
b
√
√
√
√
√
√
√
√
√
-
C
c
√
√
√
√
√
√
√
√
√
a
√
√
√
√
√
√
√
-
b
√
√
√
√
√
√
√
√
√
-
E
d
√
√
√
-
F
d
√
√
√
√
√
√
-
-
-
√
√
-
√
√
√
√
-
-
√
√
-
-
-
-
-
12
D
2.2
Configuration
After clicking the “Configuration” option, the screen will be shown as below with several menu options for users to configure
on the left side. We will thoroughly introduce them one by one in the following chapters.
Figure 2 - 4: Configure
2.2.1 Information
Users can view, after clicking “Information”, the detailed information related to the unit including Firmware Version, MAC
Address and Model Name in the middle of the screen.
Figure 2 - 5: Information
2.2.2 Image Parameter
The Image Parameter contains several basic display settings like resolution, codec, FPS, GOP and so on. In addition, it has
some extending settings including exposure, color, and white balance for the unit. Also, users can set preferred privacy zone
under this menu tree as well.
Codec
●● Edit Profiles & Streams:
Basically, this unit offers two choices of video codec for real-time viewing: H.264 or MJPEG. By default, there are up to
6 profiles, which have own respective sub settings including Resolution, Codec, Frame Rate, GOP Length, QoS (DSCP)
Codepoint, Rate Control and Bit Rate, can be chosen. And each profile contains up to 3 streams arrangement depending
on your settings: Stream1, Stream2, and Stream3, which can be configured separately to send video signals for
simultaneous triple streams with optimized quality and bandwidth based on your network environment. After setting up,
please be sure to click “Save” to have the desired settings take effect.
•
Current Profile: To choose one of the 6 profiles for implementing, click “Save Profile” after selecting.
•
Edit Profile: Select one of 6 profiles for editing the sub options.
•
MJPEG: While selecting this codec, you can then select sub menu including Frame Rate & Quality.
•
H.264: If choosing this codec, there will be more sub menu for you setting. Frame Rate, GOP Length, QoS (DSCP)
Codepoint, Rate Control, which contains 2 kinds including CBR & VBR, and each has its specific Bit Rate value control.
For more details in terms of sub settings under Codec, please refer to the tables listed below.
13
Figure 2 - 6: Basic Parameter
Table 2 - 2: Edit Profile Options
Item
Video Codec
Option
MJPEG
H.264
Description
MJPEG: Each video frame is individually compressed as single jpeg image with full-scale
contents itself and can be retouched freely with ease. However, due to completeness of
each frame, it brings about larger file size and thus easily tends to lose frames under limited
network bandwidth.
H.264: The latest best-renowned video compression format, it adopts intelligent technology
to record variation in each frame rather than record each full frame. As a result, less network
bandwidth it requires and file size is prone to be smaller compared with MJPEG.
5 M M o d e l : 5 M ( 2 5 9 2 x 1 9 4 4 ) , 3 M ( 2 0 4 8 × 1 5 3 6 ) , 5M Model:
1080P(1920×1080) , SXGA(1280×960) , 720P(1280×720), 5M(2592x1944) is the highest resolution
SVGA(800×600), VGA(640×480), VGA (640x360), QVGA (320x180) is the lowest resolution.
QVGA(320x240), QVGA (320x180)
Resolution
3M Models: 3M(2048×1536) , 1080P(1920×1080) , 3M Models:
SXGA(1280×960) , 720P(1280×720), SVGA(800×600), 3M(2048×1536) is the highest resolution
VGA(640×480), VGA (640x360), QVGA(320x240), QVGA QVGA (320x180) is the lowest resolution.
(320x180)
1M Model:
1 M M o d e l : 7 2 0 P ( 1 2 8 0 × 7 2 0 ) , S V G A ( 8 0 0 × 6 0 0 ) , 720P(1280×720) is the highest resolution
VGA(640×480), VGA (640x360), QVGA(320x240), QVGA QVGA (320x180) is the lowest resolution.
(320x180)
Note: 5M (2592x1944) can be only selected under H.264 codec mode.
Frame Rate (fps)
NTSC: 1~30
PAL: 1~25
The utmost fps settings for 2 systems varies as the following:
NTSC: H.264 single stream: 2592×[email protected]; H.264/MJPEG single stream:
2048×[email protected]; H.264/MJPEG single stream: 1920×1080 to [email protected]
PAL: H.264 single stream: 2592×[email protected]; H.264/MJPEG single stream: 2048×[email protected];
H.264/MJPEG single stream: 1920×1080 to [email protected]
GOP (Group Of
Pictures) Length
NTSC: 1~60
PAL: 1~50
Select the GOP length number from NTSC: 1 to 60 / PAL: 1 to 50. Less number means the
distance between 2 I-frames is smaller, which needs more network bandwidth with better
image. By contrast, larger number consumes less bandwidth but is hard to be recovered. The
available length number options of GOP will vary based on frame rate settings.
QoS (DSCP)
Codepoint
0 ~ 63
To classify and manage network traffic and provide quality of service (QoS) on modern IP
networks, Differentiated Services Code Point (DSCP) is a computer networking architecture
that specifies resources allocation to each device on a priority-based pattern for ideal
bandwidth management. The bigger value, the higher priority it will be.
Bit Rate Mode
CBR: Constant Bit Rate
VBR: Variable Bit Rate
Choose the bit rate control selection based on user requirements. Higher bit rate values will
result in better quality with bigger file size and thus consume more network bandwidth.
CBR stands for constant mode with certain fixed rate by user definition, while VBR means
variable mode in which users can set a range of upper and lower limits respectively for bit
rate control.
14
Table 2 - 3: Correlations of Resolution/Streams/FPS/Codecs – NTSC
Resolution
Single stream
2592x1944
(for 5M Models)
2592x1944 @ 12fps
(H.264)
2048×1536
(for 3M/5M Models)
2048×1536 @ 15fps
(H.264/MJPEG)
1920x1080
(for 3M/5M Models)
1920x1080 @ 30fps
(H.264/MJPEG)
1280×960
(for 3M/5M Models)
1280x960 @ 30fps
(H.264/MJPEG)
1280×720
(for 1M/ 3M/5M Models)
1280x720 @ 30fps
(H.264/MJPEG)
Double stream
Triple stream
2592x1944 @ 12fps, 800x600 @ 12fps
2592x1944 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 640x360 @ 12fps
2592x1944 @ 12fps, 320x240 @ 12fps
2592x1944 @ 12fps, 320x180 @ 12fps
(H.264, H.264/MJPEG)
2592x1944 @ 12fps, 800x600 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 640x480 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 640x360 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 320x240 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 320x180 @ 12fps, 640x480 @ 12fps
(H.264, H.264/MJPEG, MJPEG)
2048x1536 @ 15fps, 1280x720 @ 15fps
2048x1536 @ 15fps, 800x600 @ 15fps
2048x1536 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 640x360 @ 15fps
2048x1536 @ 15fps, 320x240 @ 15fps
2048x1536 @ 15fps, 320x180 @ 15fps
(H.264/MJPEG, H.264/MJPEG)
2048x1536 @ 15fps, 1280x720 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 800x600 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 640x480 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 640x360 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 320x240 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 320x180 @ 15fps, 640x480 @ 15fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
1920x1080 @ 30fps, 640x480 @ 30fps
1920x1080 @ 30fps, 320x240 @ 30fps
1920x1080 @ 30fps, 352x180 @ 30fps
(H.264/MJPEG, H.264/MJPEG)
1920x1080 @ 30fps, 640x480 @ 30fps, 640x360 @ 10fps
1920x1080 @ 30fps, 320x240 @ 30fps, 640x360 @ 10fps
1920x1080 @ 30fps, 352x180 @ 30fps, 640x360 @ 10fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
1280x960 @ 30fps, 1280x720 @ 30fps
1280x960 @ 30fps, 800x600 @ 30fps
1280x960 @ 30fps, 640x480 @ 30fps
1280x960 @ 30fps, 640x360 @ 30fps
1280x960 @ 30fps, 320x240 @ 30fps
1280x960 @ 30fps, 320x180 @ 30fps
(H.264/MJPEG, H.264/MJPEG)
1280x960 @ 30fps, 1280x720 @ 30fps, 640x480 @ 10fps
1280x960 @ 30fps, 800x600 @ 30fps, 640x480 @ 10fps
1280x960 @ 30fps, 640x480 @ 30fps, 640x480 @ 10fps
1280x960 @ 30fps, 640x360 @ 30fps, 640x480 @ 10fps
1280x960 @ 30fps, 320x240 @ 30fps, 640x480 @ 10fps
1280x960 @ 30fps, 320x180 @ 30fps, 640x480 @ 10fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
1280x720 @ 30fps, 1280x720 @ 30fps
1280x720 @ 30fps, 800x600 @ 30fps
1280x720 @ 30fps, 640x480 @ 30fps
1280x720 @ 30fps, 640x360 @ 30fps
1280x720 @ 30fps, 320x240 @ 30fps
1280x720 @ 30fps, 320x180 @ 30fps
(H.264/MJPEG, H.264/MJPEG)
1280x720 @ 30fps, 1280x720 @ 30fps, 640x360 @ 10fps
1280x720 @ 30fps, 800x600 @ 30fps, 640x360 @ 10fps
1280x720 @ 30fps, 640x480 @ 30fps, 640x360 @ 10fps
1280x720 @ 30fps, 640x360 @ 30fps, 640x360 @ 10fps
1280x720 @ 30fps, 320x240 @ 30fps, 640x360 @ 10fps
1280x720 @ 30fps, 320x180 @ 30fps, 640x360 @ 10fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
Table 2 - 4: Correlations of Resolution/Streams/FPS/Codecs – PAL
Resolution
Single stream
2592x1944
(for 5M Models)
2592x1944 @ 12fps
(H.264)
2048×1536
(for 3M/5M Models)
2048×1536 @ 15fps
(H.264/MJPEG)
1920x1080
(for 3M/5M Models)
1920x1080 @ 25fps
(H.264/MJPEG)
1280×960
(for 3M/5M Models)
1280x960 @ 25fps
(H.264/MJPEG)
1280×720
(for 1M/ 3M/5M Models)
1280x720 @ 25fps
(H.264/MJPEG)
Double stream
Triple stream
2592x1944 @ 12fps, 800x600 @ 12fps
2592x1944 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 640x360 @ 12fps
2592x1944 @ 12fps, 320x240 @ 12fps
2592x1944 @ 12fps, 320x180 @ 12fps
(H.264, H.264/MJPEG)
2592x1944 @ 12fps, 800x600 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 640x480 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 640x360 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 320x240 @ 12fps, 640x480 @ 12fps
2592x1944 @ 12fps, 320x180 @ 12fps, 640x480 @ 12fps
(H.264, H.264/MJPEG, MJPEG)
2048x1536 @ 15fps, 1280x720 @ 15fps
2048x1536 @ 15fps, 800x600 @ 15fps
2048x1536 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 640x360 @ 15fps
2048x1536 @ 15fps, 320x240 @ 15fps
2048x1536 @ 15fps, 320x180 @ 15fps
(H.264/MJPEG, H.264/MJPEG)
2048x1536 @ 15fps, 1280x720 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 800x600 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 640x480 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 640x360 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 320x240 @ 15fps, 640x480 @ 15fps
2048x1536 @ 15fps, 320x180 @ 15fps, 640x480 @ 15fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
1920x1080 @ 25fps, 640x480 @ 25fps
1920x1080 @ 25fps, 320x240 @ 25fps
1920x1080 @ 25fps, 352x180 @ 25fps
(H.264/MJPEG, H.264/MJPEG)
1920x1080 @ 25fps, 640x480 @ 25fps, 640x360 @ 12.5fps
1920x1080 @ 25fps, 320x240 @ 25fps, 640x360 @ 12.5fps
1920x1080 @ 25fps, 352x180 @ 25fps, 640x360 @ 12.5fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
1280x960 @ 25fps, 1280x720 @ 25fps
1280x960 @ 25fps, 800x600 @ 25fps
1280x960 @ 25fps, 640x480 @ 25fps
1280x960 @ 25fps, 640x360 @ 25fps
1280x960 @ 25fps, 320x240 @ 25fps
1280x960 @ 25fps, 320x180 @ 25fps
(H.264/MJPEG, H.264/MJPEG)
1280x960 @ 25fps, 1280x720 @ 25fps, 640x480 @ 12.5fps
1280x960 @ 25fps, 800x600 @ 25fps, 640x480 @ 12.5fps
1280x960 @ 25fps, 640x480 @ 25fps, 640x480 @ 12.5fps
1280x960 @ 25fps, 640x360 @ 25fps, 640x480 @ 12.5fps
1280x960 @ 25fps, 320x240 @ 25fps, 640x480 @ 12.5fps
1280x960 @ 25fps, 320x180 @ 25fps, 640x480 @ 12.5fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
1280x720 @ 25fps, 1280x720 @ 25fps
1280x720 @ 25fps, 800x600 @ 25fps
1280x720 @ 25fps, 640x480 @ 25fps
1280x720 @ 25fps, 640x360 @ 25fps
1280x720 @ 25fps, 320x240 @ 25fps
1280x720 @ 25fps, 320x180 @ 25fps
(H.264/MJPEG, H.264/MJPEG)
1280x720 @ 25fps, 1280x720 @ 25fps, 640x360 @ 12.5fps
1280x720 @ 25fps, 800x600 @ 25fps, 640x360 @ 12.5fps
1280x720 @ 25fps, 640x480 @ 25fps, 640x360 @ 12.5fps
1280x720 @ 25fps, 640x360 @ 25fps, 640x360 @ 12.5fps
1280x720 @ 25fps, 320x240 @ 25fps, 640x360 @ 12.5fps
1280x720 @ 25fps, 320x180 @ 25fps, 640x360 @ 12.5fps
(H.264/MJPEG, H.264/MJPEG, MJPEG)
15
Exposure
Figure 2 - 7: Exposure
Exposure Mode
It controls the light intensity of picture. There are 2 modes, Manual Exposure and Auto Exposure for adjustment depending
on different conditions. When in Manual mode, Shutter Speed is adjustable.
Advanced Exposure
Advanced exposure section is for users to modify more detailed options related to exposure.
• EV Compensation: It is the exposure compensation telling the unit by setting value from -2.0 to 2.0 with intervals of per 0.5
for scenes to be either darker or brighter. (Unavailable when exposure mode is manual)
•
Day & Night: Set DAY/NIGHT function by selecting Auto/Color/BW mode. If selected Color mode, the unit is forced to stay in
DAY (COLOR) mode all day and BW for Black & White (Night) mode.
•
Noise Reduction: It is the process of removing noises from a signal and be set from 0-255 to decrease noise on the screen.
•
BLC: Set an area for Backlight Compensation. Backlight Compensation is a function that achieves the brightness of a selected
area to optimal image level. This function is necessary when an auto iris lens tends to close due to an intense light coming
from back of object in the area wished to view so that the area is too dark and difficult to see. In this case, users may set the
area corresponding to the portion wished to see. (Unavailable when exposure mode is manual)
•
WDR: It is intended to provide clear images even under backlight circumstances where intensity of illumination can vary
excessively, namely where there are both very bright and very dark areas simultaneously in the field of view. WDR enables
the capture and display of both bright and dark areas in the same frame, in a way that there are details in both areas, i.e.
bright areas are not saturated, and dark areas are not too dark.
Note
Settings will be restored to the factory defaults if pressing “Reset to default”.
16
White Balance
To set the white balance values to meet ambience condition for best color rendition with 2 modes:
Figure 2 - 8: White Balance Settings
●● Auto
It automatically controls color temperature ranging from 2500°K to 10000°K
●● Manual
To manually set preferred gain values including the following:
• R (Red) Gain: It allows users to adjust red color in the image ranging from 0 to 255.
•
G (Green) Gain: It allows users to adjust green color in the image ranging from 0 to 255.
•
B (Blue) Gain: It allows users to adjust blue color in the image ranging from 0 to 255.
Note
Settings will be restored to the factory defaults if pressing “Reset to default”.
Basic Color
Figure 2 - 9: Basic Settings
●● Brightness
Set image brightness from level -255 to 255. The 255 indicates the brightest image.
●● Contrast
Set image contrast from level 0 to 255. The 255 provides the highest contrast
●● Hue
Set picture hue from level -15 to 15. Selecting 15 provides the deepest hue.
●● Saturation
It describes the difference of a color from the gray of the same lightness. Increasing saturation deepens the colors of your
images, making reds redder and blues bluer. Users can adjust picture saturation level from 0 to 255. Decreasing saturation
brings the image closer to a grayscale (that is, monochrome or black-and-white) image. Selecting 255 provides the highest
image saturation.
17
●● Sharpness
Increasing the sharpness value will sharpen the edges and small feature of viewing images. If the edges appear too
smooth or blurred, increase the sharpness; otherwise, decrease the sharpness. Sharpness value can be set from 0 to 15.
The 15 offers the sharpest image.
●● Gamma Correction
Set gamma correction between 1 and 0.45.
●● Video Orientation
Set image to be left right reversal, upside down or both by selecting “Mirror”, “Flip” and “Both” individually. Selecting “OFF”
will deactivate video orientation function.
Note
Settings will be restored to the factory defaults if pressing “Reset to default”.
Remote Lens Control
(Motorized Lens Model Exclusive)
Figure 2 - 10: Remote Lens Control
●● Zoom Control
• Zoom Limit could be set between x3 and x30
•
Zoom speed could be selected among High, Medium and Low
•
By clicking “Start”, users can zoom in/out the lens continuously for a close-up or a wide view, while clicking “Stop” to end
zoom in/out actions.
●● Focus Control
• The “Manual Focus Continuous” lets users start Focus Near/Focus Far to adjust the focus for better plainness of image. Click
“Start” to carry out action continuously and “Stop” to end the action.
•
The “Manual Focus Stepping” has the fine-tuning ability for focus control. The “Normal Step” for Focus Near/Focus Far enables
users to manually control desired focus step by step with one click each time differing from Manual Focus Continuous.
•
The “Fine Step”, compared with Normal Step, allows users to exert much slighter manual adjustment on focus control even
more subtly.
•
Click “Start Focus” after selecting “One-Push AF” to have the lens focus automatically immediately.
•
Click “Start Calibration” after selecting “One-Push AF” to have the lens calibrate and focus auto simultaneously at once.
18
Privacy Zone
Privacy Zone enables users to black out a specific portion of the screen for privacy concern. There are up to 8 sets of privacy
zones for users to define. After setting up a privacy zone, the live view screen will appear a frame, whose color, size and
position can be customized by users’ preference.
Figure 2 - 11: Privacy Zone Setting
To set up a privacy mask, you need first to turn ON one of the eight privacy zones (multiple available) and adjust the privacy
mask size by pressing with left click and dragging to outline a desired privacy frame. Also, users can select a desired color
(Black, Grey or White) for privacy zone. Press “Save Mask zone” to make settings take effect. If you intend to delete settings,
click “Clean Mask zone” to wipe out privacy zone settings.
Note
It is recommended to set the privacy zone slightly larger than the actual area to ensure that privacy area is
not revealed during movement.
19
2.2.3 Network Settings
Network
This section for users to set detailed settings related to wired network condition for the unit.
Figure 2 - 12: Network
●● Network Settings
• View current network settings: Click “View” to see your current network related settings.
Figure 2 - 13: Current Network Settings
•
Camera Name: Input your preferred camera name here.
•
HTTP Port: This protocol allows for TCP protocol quality without having to open specific ports for streaming. Users inside
a firewall can utilize this protocol to allow streaming data through. It is recommended to use the default port number 80;
however, if it is required to change the port number, please contact your system administrator with options ranging from
1025 to 65535.
•
HTTPS Port: More secured than HTTP, HTTPS is based on HTTP with SSL/TLS protocol, therefore increasing the security
capabilities of SSL/TLS on standard HTTP communications. By default, it’s recommended to adopt 443 as the initial port
number. Nevertheless, please also contact your system administrator for other port number ranging from 1025 to 65535 if
required.
●● IPv4 Address Configure
To set your IP address with further settings under IPv4 here.
• DHCP: If enabled, the unit will automatically obtain an available dynamic IP address from the DHCP server each time it
connects to the LAN.
•
IPv4 Address: To manually set an IP address under IPv4.
•
Subnet Mask: Please use default address: 255.255.255.0. If subnet mask is not properly configured, the unit may not be able
to communicate with other devices.
•
Default Gateway: Leave blank as default setting. No Default Gateway address required if not used. Ask your network
administrator for further information.
•
Primary DNS: Same as the above.
•
Secondary DNS: Same as the above.
20
●● UPnP
• When UPnP (Universal Plug & Play) is set to “ON”, the unit can be detected automatically by any computer in the LAN to skip
the installation of the IP Finder utility.
●● OSD
• “Camera Name” and “Date & Time” can be set ON to show on screen separately.
FTP
(1M Flat Mini Dome Network Camera Excluding)
In this page, users can set FTP connection related settings.
Figure 2 - 14: FTP Settings
●● Action
Simply click “ON” to activate the FTP function or “OFF” to disable it.
●● Login ID
Enter a login ID to be allowed to connect with FTP.
●● Password
Enter a password associated with the login ID.
●● Max Simultaneous Connection
Determine the number of maximum connections by inputting a number in the Max Simultaneous Connections field.
Please note that it is the maximum of FTP Client connections, not the maximum of IE Window’s connections.
To log on the FTP, simply enter ftp://<Login ID>:<Password>@<ip address> in the location field of Microsoft’s Internet
Explorer and the recordings will be shown up. The default setting is ftp://admin:[email protected] Refer to the names of
file and the folder for date and time of recordings.
Note
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set all the settings
back to the factory defaults.
21
RTSP
To enable RTSP, simply enter the Login ID, Password and Port (554 by default) with selecting “ON” in Authentication.
Figure 2 - 15: RTSP Settings
●● URL
Input a preferred name for representing each RTSP Stream URL. Please note that there’re 2 transferring types of each
stream: Unicast and Multicast, and the URL name for each will be as the example below:
• Unicast: stream1
•
Multicast: stream1m
●● Multicast Address
The IP address for multicasting ought to be from 224.0.1.1 to 239.255.255.254. The RTSP URLs for RTSP Stream 1, RTSP
Stream 2, and RTSP Stream3 are as following respectively:
• rtsp://(ip address)/(stream 1)
•
rtsp://(ip address)/(stream 2)
•
rtsp://(ip address)/(stream 3)
For example: rtsp://224.0.1.1/stream1
●● Audio Multicast Address
Similar to the above, IP address of audio multicast, responsible for audio transmitting, should be defined from 224.0.1.1 to
239.255.255.254 as well.
Note
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set all the settings
back to the factory defaults.
22
SNMP
SNMP (Simple Network Management Protocol) is an Internet standard protocol on top of application layer that restructures
the exchange of management information among network-attached nodes, which helps administrators to remotely manage
network devices and master network problems with ease.
Figure 2 - 16: SNMP Settings
●● SNMP V1
Tick “ON” or “OFF” to enable or disable.
●● SNMP V2
Tick “ON” or “OFF” to enable or disable.
●● SNMP V3
Tick “ON” or “OFF” to enable or disable. Enter password corresponding to User Name. SNMPv3 provided more security
features than SNMP V1/SNMP V2.
●● Read/Write Community String
Enter the names of Read Community String and Write Community String.
●● Trap
Trap under SNMP allows an agent to notify the management station of significant events by way of an unsolicited SNMP
message, the asynchronous notification. Tick “ON” or “OFF” to enable or disable trap function here. Input IP address of Trap
Host.
●● Heartbeat
To ensure a network free from delayed message, Heartbeat, this communications protocol sends back a message in a
given interval to properly confirm message is alive and in fact with a periodic heartbeat. Tick “ON” or “OFF” to enable or
disable heartbeat function here. Input IP address & Interval of Heartbeat Host.
●● Download MIB
Click “Download” to get specifics of MIB (Management Information Base). MIBs describe the structure of the management
data of a device subsystem; which uses a hierarchical namespace containing object identifiers (OID). Each OID identifies a
variable that can be read or set via SNMP.
Note
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set all the settings
back to the factory defaults.
23
802.1X
802.1X is an IEEE Standard for Port-based Network Access Control and defines the encapsulation of the Extensible
Authentication Protocol (EAP) over IEEE 802 which is known as EAP over LAN. Simply click “ON” to activate it and further
select its related EAP protocol types.
Figure 2 - 17: 802.1X Settings
●● EAP-MD5
It is the only IETF Standards Track based EAP method and offers the minimal security.
●● EAP-TLS
Transport Layer Security (TLS) is an IETF open standard and is well-supported among wireless vendors. Still, it is considered
one of the most secure EAP standards available
●● EAP-TTLS
Tunneled Transport Layer Security (TTLS) is an EAP protocol that extends TLS and is widely supported across platforms.
●● EAP-PEAP
The Protected Extensible Authentication Protocol (PEAP) was jointly developed by Cisco Systems, Microsoft, and RSA
Security and provides unique security for users.
Note
Please click “Save” button to make your settings take effect.
2.2.4 Account Management
Account Settings
Figure 2 - 18: Account Settings
●● Admin:
The unit privileged control can be defined under Admin level right here.
The default settings for system Login ID and Password are:
• Username: admin
•
Password: 1234
24
●● User:
Other than admin, Guest level can only access to unit under authorization from system administrator. At most 5 users are
allowed to view live view. No operation will be granted without authorization. The default user’s login name and password
are “user1” (user1~5) and “0000”.
To add/delete/change admin/user settings, please refer to the details below.
• New User: To add a new user, simply click “New User” and then input a desired username with password (reenter for
reconfirm). Finally click “Save” to take effect.
•
Delete User: Choose one of the users from the list and then click “Delete User” to remove it.
•
Change Password: Choose admin or one of the users from the list first, and enter an updated password (reenter for
reconfirm). Finally click “Save” to take effect.
Caution
Note
•
The login ID and Password is supported within 16 characters with the valid alphanumeric value merely
including '0' to '9', 'a' to 'z', 'A' to 'Z', '.','-','+','_'and '@'.
•
It is NOT allowed to add or delete Admin Level user, which is only one by default.
Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings
back to the factory defaults.
2.2.5 Event Settings
Motion Detection
This function is designed to trigger a corresponding action when the unit detects motion(s).
Figure 2 - 19: Motion Detection Settings
●● Enable
Set “ON” to activate motion detection function.
●● Sensitivity
Choose different 3 levels of detecting sensitivity. “High”: Motion is activated with slight changes in brightness or motion.
“Low”: Motion is activated with big changes in brightness or motion.
●● Detect Zone
Adjust the detect zone by pressing with left click and dragging on the live view screen to outline a desired size of detected
frame.
●● Clean
Click “Clean” to erase detect zone settings.
Note
Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings
back to the factory defaults.
25
Alarm I/O
(1M/3M Flat Mini Dome Network Camera Excluding)
Connecting an alarm input device with the camera can largely extend warning functions. For example, when an infrared
detector connected with the camera detects motion based on heat emission, an alarm message would be displayed on the
Web-Client screen for notification. On the other hand, by connecting with an alarm output device such as siren, the camera
will send signal to notify siren and thus make it activated when detecting an alarm either by motion detection or signals from
alarm input devices.
Figure 2 - 20: Alarm Input / Output Settings
●● Alarm Input
• Enable: Set Alarm Input as “ON” or “OFF”.
•
Type: Choose NO for normally open or NC for normally close. NO (Normally Opened): An alarm will be triggered when the
external contact closes. NC (Normally Closed): An alarm will be triggered when the external contact opens.
●● Alarm Output
• When set to “On”, external devices such as sirens or flashing lights that connected to the alarm output connector will signal
for alarm activation. And duration can be defined among 0/5/10 seconds, in which 5 seconds is the default settings. 0
second indicates unlimitedly continuous triggering while 5 and 10 seconds mean there’s a time interval between triggering
for respective settings.
Note
Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings
back to the factory defaults.
Email Notification
Figure 2 - 21: Email Notification
26
●● SMTP Recording Condition
Simple Mail Transfer Protocol (SMTP) is an Internet standard for e-mail service across networking. Users can receive Alarm
or Motion triggered event via email notification by setting here.
●● SMTP Server
• SMTP Server: Input a server name or address.
•
Login ID: Input a user name with privilege to access the server.
•
Password: Input the password associated with Login ID.
•
Sender Mail Address: Enter the mail address of the sender
•
Port: Set “25” as default or change to dedicated number.
•
Authentication: Select an authentication type as following details:
»»
No_Auth: No restriction
»»
SMTP_Plain: PLAIN is the name of a registered SASL authentication mechanism which serves as a parameter to the
AUTH command. The PLAIN authentication mechanism is described in RFC 2595. Plain is the least secure of all the SASL
authentication mechanisms since the password is sent unencrypted across the network.
»»
Login: The Login mechanism is supported by Microsoft's Outlook Express and by some other clients.
»»
TLS_TTLS: TLS is usually implemented on top of any of the Transport Layer protocols encapsulating the applicationspecific protocols such as HTTP, FTP, SMTP, NNTP and XMPP. The TLS protocol allows client-server applications to
communicate across a network in a way designed to prevent eavesdropping and tampering. TLS can also be used to
tunnel an entire network stack to create a VPN as is the case with OpenVPN.
●● Email Notification Triggered
Either Motion detection or Alarm input is enabled; users can edit the related sending mail settings below:
• Subject: To preset a subject of sending email.
•
Message: To preset message contents of sending email.
•
Attach Image: Select “On” to enable attach the detected image to the sending email.
●● E-mail Address List:
This function is designed to notify multiple users via email when alarm in or motion detection functions are set.
• Tick “Enable” and input the assigned email address accordingly.
•
Address: Input an email address to which alarm and motion events will be sent. There’re maximum 10 email addresses can
be defined here.
•
Select either detection (Alarm, Motion) or both for sending email.
Note
Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings
back to the factory defaults.
27
2.2.6 Record Settings
FTP Recording
Users can save image files via FTP server by setting FTP recording condition beforehand.
Figure 2 - 22: FTP Recording
●● FTP Recording Conditions
You can store the image files by either mode including scheduled recording, alarm input triggered recording or motion
detection triggered recording.
●● FTP Server
FTP (File Transfer Protocol) is used as a service component to transfer files by simply entering the FTP IP address or
hostname with the Login ID and password.
• FTP Sever: Input a FTP server name.
•
Login ID: Input a user name with privilege to access the server.
•
Password: Input the password associated with Login ID.
•
Port: Set “21” as default or change to dedicated number.
●● Scheduled Recording to FTP
Determine the scheduled recording condition: OFF, All Day, Schedule 1, or Schedule 2 during 24/7.
Figure 2 - 23: Scheduled Recording to FTP Settings
•
Recording cycle: Set a time interval from 5 to 120 seconds for recording images.
•
File Name Prefix: Set a prefixed name for recording file.
•
Server Path: Set the desired path where the data is to be stored on the server.
●● Alarm/Motion Event Recording to FTP
These functions are to define the way to record video once a motion/alarm event is detected by the unit (1M/3M Flat Mini
Dome Network Camera do not support alarm event recording).
28
Figure 2 - 24: Alarm/Motion Event Recording to FTP Settings
•
Pre Recording Frame: Set the number of frame to be recorded immediately before an event occurs.
•
Pre Recording Cycle: Set a time interval before recording.
•
Recording Frame: Set the number of frame while recording.
•
Recording Cycle: Set a time interval for recording.
•
File Name: Set file name to be stored for motion/alarm events separately.
•
Sever Path: Set the desired path on the server to store data for motion/alarm events.
Note
Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings
back to the factory defaults.
Edge Recording
(1M Flat Mini Dome Network Camera Excluding)
Image files can be saved onto the SD card through well setting in this section. Please make sure to insert SD card prior to
enabling this function.
Figure 2 - 25: Edge Recording
●● Edge Recording Conditions
Choose one of the conditions to enable the SD card recording: Alarm, Motion, or Network Lose.
●● System Information
• Alarm/Motion Recording Time: Set a time interval for SD card recording of alarm or motion event triggered.
•
Auto Overwrite: Set “OFF” or “ON” to disable or enable overwriting SD card automatically when SD card is full of recording
files.
●● SD Card Information
• Usage: Information of memory card usage.
•
SD Format: To execute memory card format process.
29
2.2.7 System Settings
Date & Time
Figure 2 - 26: Date & Time
●● Current Server Time
The server current date/time is displayed here.
●● Synchronization Mode
There’re 3 modes for users to set date/time.
• Manual: Select it to manually set your date/time.
•
Synchronize with PC Date: Select it to simply synchronize date/time with computer.
•
Synchronize with NTP Server: Select it to synchronize date/time with the assigned NTP server.
●● NTP
Set up your NTP related settings here if NTP Server enabled.
• NTP Server: Please input desired NTP server in the field.
•
Synchronizing Period: Select sync period between 1 and 24 by 6 of each interval.
•
NTP Test: Click it to test if your assigned NTP server is workable.
●● Time Zone
Choose one of the time zones based on your located country/area
Note
Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings
back to the factory defaults.
30
Audio
(1M Flat Mini Dome Network Camera Excluding)
Figure 2 - 27: Audio Settings
●● Type
Two audio codecs G711-Alaw/G711-Ulaw can be chosen from. (Audio Input only)
●● Enable
Set "ON" to activate audio input/output when audio input/output devices are plugged.
●● Level
The sound levels are selectable for audio input/output: Low/Mid/High for audio input/output.
Note
Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings
back to the factory defaults.
Firmware Update
Users can manually update System Firmware if available. All unit motions will be stopped during firmware update. Please
close any other screens before firmware update. Never disconnect power or LAN cable during the updating process. It takes
approximately 3 minutes for the unit to reboot after firmware update process. Please reboot the computer as well after
firmware updated. Again, power can’t be lost when updating firmware since it will cause the update failure and manufacturer
maintenance will be required.
Figure 2 - 28: Firmware Update
●● Click Browse to choose a corresponding firmware version and click Upload to proceed.
31
Initialize
Figure 2 - 29: Initialize Settings
●● Video Type
Select “NTSC” or “PAL” as required. Flickering by fluorescent light can be reduced by selecting “PAL” for the power frequency
50Hz, “NTSC” for the power frequency 60Hz
●● Import User Configuration
Press “Browse” to select the file and then click “Import” to upload configuration settings from local to the unit.
●● Export User Configuration
Press “Export” to download configuration settings to local computer.
●● Reboot Camera
Press “Reboot Camera” to reboot the unit.
●● Software Factory Default
Press it to reset all configuration settings back to factory defaults excluding network settings.
●● Remote Hardware Factory Default
Press it to reset all configuration settings back to factory defaults.
2.2.8 Event Log
Figure 2 - 30: System Log
●● Click “Download Log” to save the log file of unit to your local computer.
32
Appendix A: Specifications of Indoor Dome Network
Camera (Manual Focus Model)
Video
Model Type
Sensor Type
Active Pixels
Compression
Streaming
Resolution
1M Manual Focus Model
1/4" progressive scan CMOS sensor
1280 x 800 (HxV)
H.264 / MJPEG
Triple simultaneous streams with multiple video profile
720P, SVGA(800x 600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
Max. Frame Rate
HDTV 720p (1280x720) at 30/25fps (NTSC/PAL)
Day/Night
Day/Night Mode
Mechanical (ICR) D/N Control
Auto/ BW/ Color
1/10,000s to 1/7.5s Selectable (60Hz);
1/10,000s to 1/6.25s Selectable (50Hz)
Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE, F1.4;
B/W: 0.02 lux at 50 IRE, 0.004 lux at 10 IRE, F1.4
(Shutter speed: 1/15 sec)
NTSC: 720x480 @30fps; PAL: 720x576 @25fps
CBR, VBR
Shutter Time
Minimum Illumination
Video Output
Bit Rate Control
Lens
Lens Type
Focal Length
Focus / Zoom
View Angle
IRIS Control
Audio
Audio Communication
Compression
Audio In/Out
Image Enhancement
Built-in; Varifocal
f=2.8~10mm, F1.4
Manual
H: 68°(Wide)~23°(Tele)
DC IRIS
3M Manual Focus Model
1/3" progressive scan CMOS sensor
2304 x 1536 (HxV)
QXGA(2048x1536), 1080P, 1280x960, 720P, 800x600,
VGA(640x480), 640x360, QVGA(320x240), 320x180
3MP 4:3 (2048x1536) at 15fps;
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
f=3~9mm, F1.2
H: 78°(Wide)~28°(Tele)
Two-way Audio
G.711 PCM 8kHz, a/μ-law support
External microphone and speaker
AES, AWB, AGC
Exposure Mode: AES / ALC / Flickerless / Manual;
White Balance: Auto / Manual;
Image Settings
Backlight Compensation
Configurable Brightness, Contrast, Hue, Saturation, and Sharpness
Gamma Correction
WDR
Enhanced Digital WDR
DNR
Configurable 3DNR setting
Privacy Zone
Yes, up to 8 privacy zones
Image Orientation
Mirror, Flip
Frequency Control
NTSC(60Hz)/ PAL(50Hz)
Date & Time Stamp
Yes
Intelligent Video & Event Management
Motion Detection
Yes, 3-level sensitivity
Ethernet Detection
Network loss detection
Others
Optimized i-frame (GOP) setting
Events
Motion detection, ethernet detection, external alarm
Event snapshot to remote FTP storage / email recipients;
Event Actions
Edge recording to SD card;
HTTP event query, HTTP event client pulling
Store Category
Event snapshot, Edge recording, Manual Snapshot, Manual Recording
Local Storage
Memory Card Slot
SDXC/SDHC card support
Memory Card Overwrite
Yes
33
Network
Protocol
Ethernet
ONVIF
Browser
Security
I/O & Controls
Power
Power LED Indicator
Alarm In/Out
Network
Audio In/Out
Analog Video
System Reboot
Factory Default
Power
Power Requirement
Power Consumption (Max.)
Mechanical
Dimensions(ΦxH)
Weight
3-Axis
Pan/Tilt Adjustment
Environmental
Operating Temperature
Operating Humidity
Storage Temperature
Regulatory
Approvals
ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,
UPnP, IEEE802.1X
10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45
Yes
Internet Explorer, Chrome, Firefox, Safari
Multiple user access levels with password protection; IP address filtering;
IEEE 802.1X network access control, HTTPS encryption, and digest authentication
2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE
System power and status indicator
Terminal block 1 in / 1 relay out(30V, 1A)
RJ-45 with LED Indicator
Terminal block 1 in / 1 out
1 x composite video out, micro JST
Reset x 1
Default x 1, pressing 5 sec for loading factory default
DC 12V & AC 24V ± 10% / PoE (IEEE 802.3af, class 0)
6W
Φ125mm x 106mm (Φ4.92" x 4.18")
500g (1.1 lb)
Yes
Pan: 0°-350°, Tilt: 15°-90°, Rotate: 0°-350° (Max.)
-10ºC ~ 50ºC (-14ºF ~ 122ºF)
90% RH, non-condensing
-40°C ~ 60°C (-40°F ~ 140°F)
CE, FCC, RoHS
Note: Product specifications and pictures are subject to change without notice.
34
6.5W
Appendix B: Specifications of Indoor Dome Network
Camera (Motorized Lens Model)
Video
Model Type
Sensor Type
Active Pixels
Compression
Streaming
Resolution
Max. Frame Rate
Day/Night
Day/Night Mode
Shutter Time
Minimum Illumination
Video Output
Bit Rate Control
Lens
Lens Type
Focal Length
Focus / Zoom
View Angle
IRIS Control
Audio
Audio Communication
Compression
Audio In/Out
Image Enhancement
3M Motorized Lens Model
1/3" progressive scan CMOS sensor
2304 x 1536 (HxV)
H.264 / MJPEG
Triple simultaneous streams with multiple video profile
Q X G A ( 2 0 4 8 x 1 5 3 6 ) , 1 0 8 0 P, 1 2 8 0 x 9 6 0 , 7 2 0 P,
SVGA(800x600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
3MP 4:3 (2048x1536) at 15fps;
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
Mechanical (ICR) D/N Control
Auto/ BW/ Color
1/10,000s to 1/7.5s Selectable (60Hz);
1/10,000s to 1/6.25s Selectable (50Hz)
Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE;
B/W: 0.02 lux at 50 IRE, 0.04 lux at 10 IRE;
F1.2, (Shutter speed: 1/15 sec)
NTSC: 720x480 @30fps; PAL: 720x576 @25fps
CBR, VBR
Built-in; Varifocal
f=3~9mm, F1.2
Autofocus, motorized / Remote
H: 78°(Wide)~28°(Tele)
DC IRIS
5M Motorized Lens Model
1/3.2" progressive scan CMOS sensor
2592x1944 (HxV)
2592x1944, QXGA(2048x1536), 1080P, 1280x960,
720P, SVGA(800x 600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
5MP 4:3 (2592x1944) at 12 fps
3MP 4:3 (2048x1536) at 15 fps
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
Color: 0.15 lux at 50 IRE, 0.03 lux at 10 IRE,
B/W: 0.03 lux at 50 IRE, 0.006 lux at 10 IRE,
F1.2 (Shutter speed: 1/15 sec)
Autofocus, motorized / Remote
Two-way Audio
G.711 PCM 8kHz, a/μ-law support
External microphone and speaker
AES, AWB, AGC
Exposure Mode: AES / ALC / Flickerless / Manual;
White Balance: Auto / Manual;
Image Settings
Backlight Compensation
Configurable Brightness, Contrast, Hue, Saturation, and Sharpness
Gamma Correction
WDR
Enhanced Digital WDR
DNR
Configurable 3DNR setting
Privacy Zone
Yes, up to 8 privacy zones
Image Orientation
Mirror, Flip
Frequency Control
NTSC(60Hz)/ PAL(50Hz)
Date & Time Stamp
Yes
Intelligent Video & Event Management
Motion Detection
Yes, 3-level sensitivity
Ethernet Detection
Network loss detection
Others
Optimized i-frame (GOP) setting
Events
Motion detection, ethernet detection, external alarm
Event snapshot to remote FTP storage / email recipients;
Event Actions
Edge recording to SD card;
HTTP event query, HTTP event client pulling
Store Category
Event snapshot, Edge recording, Manual Snapshot, Manual Recording
Local Storage
Memory Card Slot
SDXC/SDHC card support
Memory Card Overwrite
Yes
35
Network
Protocol
Ethernet
ONVIF
Browser
Security
I/O & Controls
Power
Power LED Indicator
Alarm In/Out
Network
Audio In/Out
Analog Video
System Reboot
Factory Default
Power
Power Requirement
Power Consumption (Max.)
Mechanical
Dimensions(ΦxH)
Weight
3-Axis
Pan/Tilt Adjustment
Environmental
Operating Temperature
Operating Humidity
Storage Temperature
Regulatory
Approvals
ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,
UPnP, IEEE802.1X
10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45
Yes
Internet Explorer, Chrome, Firefox, Safari
Multiple user access levels with password protection; IP address filtering;
IEEE 802.1X network access control, HTTPS encryption, and digest authentication
2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE
System power and status indicator
Terminal block 1 in / 1 relay out(30V, 1A)
RJ-45 with LED Indicator
Terminal block 1 in / 1 out
1 x composite video out, micro JST
Reset x 1
Default x 1, pressing 5 sec for loading factory default
DC 12V & AC 24V ± 10% / PoE (IEEE 802.3af, class 0)
7W
Φ125mm x 106mm (Φ4.92" x 4.18")
500g (1.1 lb)
Yes
Pan: 0°-350°, Tilt: 15°-90°, Rotate: 0°-350° (Max.)
-10ºC ~ 50ºC (-14ºF ~ 122ºF)
90% RH, non-condensing
-40°C ~ 60°C (-40°F ~ 140°F)
CE, FCC, RoHS
Note: Product specifications and pictures are subject to change without notice.
36
Appendix C: Specifications of Outdoor IR Dome Network
Camera
Video
Model Type
3M Manual Focus Model
Sensor Type
1/3" progressive scan CMOS sensor
Active Pixels
Compression
Streaming
2304 x 1536 (HxV)
H.264 / MJPEG
Triple simultaneous streams with multiple video profile
Resolution
Max. Frame Rate
Day/Night
Day/Night Mode
Shutter Time
Minimum Illumination
Video Output
Bit Rate Control
Lens
Lens Type
Focal Length
Focus / Zoom
View Angle
IRIS Control
IR LEDs
LED Quantity
IR Distance
IR Turn on Status
LED Life
Audio
Audio Communication
Compression
Audio In/Out
Image Enhancement
3M Motorized Lens Model
5M Motorized Lens Model
1/3.2" progressive scan CMOS
sensor
2592x1944 (HxV)
2592x1944, QXGA(2048x1536),
QXGA(2048x1536), 1080P, 1280x960, 720P, SVGA(800x600), VGA(640x480), 1080P, 1280x960, 720P, SVGA(800x
640x360, QVGA(320x240), 320x180
600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
5MP 4:3 (2592x1944) at 12 fps
3MP 4:3 (2048x1536) at 15fps;
3MP 4:3 (2048x1536) at 15 fps
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
2MP Full HD 16:9 (1920x1080) at
30/25fps (NTSC/PAL)
Mechanical (ICR) D/N Control
Auto/ BW/ Color
1/10,000s to 1/7.5s Selectable (60Hz);
1/10,000s to 1/6.25s Selectable (50Hz)
IR LED OFF:
IR LED OFF:
Color: 0.15 lux at 50 IRE,
Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE;
0.03 lux at 10 IRE;
F1.2 (Shutter speed: 1/15 sec)
F1.2(Shutter speed: 1/15 sec)
IR LED ON: 0 lux
IR LED ON: 0 lux
NTSC: 720x480 @30fps; PAL: 720x576 @25fps
CBR, VBR
Built-in; Varifocal
f=3~9mm, F1.2
Manual
H: 78°(Wide)~28°(Tele)
DC IRIS
20 pcs(850nm)
20 meters (65ft)
Under 5 lux by auto control
More than 10,000 hours
Auto Focus / Motorized remote focus control
25 meters (82ft)
Two-way Audio
G.711 PCM 8kHz, a/μ-law support
External microphone and speaker
AES, AWB, AGC
Exposure Mode: AES / ALC / Flickerless / Manual;
White Balance: Auto / Manual;
Image Settings
Backlight Compensation
Configurable Brightness, Contrast, Hue, Saturation, and Sharpness
Gamma Correction
WDR
Enhanced Digital WDR
DNR
Configurable 3DNR setting
Privacy Zone
Yes, up to 8 privacy zones
Image Orientation
Mirror, Flip
Frequency Control
NTSC(60Hz)/ PAL(50Hz)
Date & Time Stamp
Yes
Intelligent Video & Event Management
Motion Detection
Yes, 3-level sensitivity
Ethernet Detection
Network loss detection
37
Others
Events
Event Actions
Store Category
Local Storage
Memory Card Slot
Memory Card Overwrite
Network
Protocol
Ethernet
ONVIF
Browser
Security
I/O & Controls
Power
Power LED Indicator
Alarm In/Out
Network
Audio In/Out
Analog Video
System Reboot
Factory Default
Power
Power Requirement
Power Consumption (Max.)
Mechanical
Dimensions(ΦxH)
Weight
3-Axis
Pan/Tilt Adjustment
Protection
IK10 Compliant
Operating Temperature
Operating Humidity
Storage Temperature
Regulatory
Approvals
Optimized i-frame (GOP) setting
Motion detection, ethernet detection, external alarm
Event snapshot to remote FTP storage / email recipients;
Edge recording to SD card;
HTTP event query, HTTP event client pulling
Event snapshot, Edge recording, Manual Snapshot, Manual Recording
microSDXC/SDHC card support
Yes
ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,
UPnP, IEEE802.1X
10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45
Yes
Internet Explorer, Chrome, Firefox, Safari
Multiple user access levels with password protection; IP address filtering;
IEEE 802.1X network access control, HTTPS encryption, and digest authentication
2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE
System power and status indicator
Terminal block 1 in / 1 relay out(30V, 1A)
RJ-45 with LED Indicator
Terminal block 1 in / 1 out
1 x composite video out, micro JST
Reset x 1
Default x 1, pressing 5 sec for loading factory default
Heater Drive: AC 24V ± 10% / PoE (IEEE 802.3af )
*Arctic power-on support by PoE at -50°C
Defrost Drive: AC 24V ± 10%
26W
Φ147mm x 140mm (Φ5.79" x 5.5")
1250g (2.76 lb)
Yes
Pan: 0°-350°, Tilt: 15°-90°, Rotate: 0°-350° (Max.)
IP66 Certified, IP67/IP68 Compliant, IK10 Compliant
-50ºC ~ 50ºC (-58ºF ~ 122ºF)
90% RH, non-condensing
-20°C ~ 60°C (-4°F ~ 140°F)
CE, FCC, RoHS
Note: Product specifications and pictures are subject to change without notice.
38
Appendix D: Specifications of Fixed Network Camera
Video
Model Type
Sensor Type
Active Pixels
Compression
Streaming
Resolution
Max. Frame Rate
Day/Night
Day/Night Mode
Shutter Time
Minimum Illumination
Video Output
Bit Rate Control
Lens
IRIS Control
Lens Mount
Audio
Audio Communication
Compression
Audio In/Out
Image Enhancement
3M Fixed Network Camera
1/3" progressive scan CMOS sensor
2304 x 1536 (HxV)
H.264 / MJPEG
Triple simultaneous streams with multiple video profile
Q X G A ( 2 0 4 8 x 1 5 3 6 ) , 1 0 8 0 P, 1 2 8 0 x 9 6 0 , 7 2 0 P,
SVGA(800x600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
3MP 4:3 (2048x1536) at 15fps;
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
Mechanical (ICR) D/N Control
Auto/ BW/ Color
1/10,000s to 1/7.5s Selectable (60Hz);
1/10,000s to 1/6.25s Selectable (50Hz)
Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE;
B/W: 0.02 lux at 50 IRE, 0.04 lux at 10 IRE;
F1.2, (Shutter speed: 1/15 sec)
NTSC: 720x480 @30fps; PAL: 720x576 @25fps
CBR, VBR
5M Fixed Network Camera
1/3.2" progressive scan CMOS sensor
2592x1944 (HxV)
2592x1944, QXGA(2048x1536), 1080P, 1280x960,
720P, SVGA(800x 600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
5MP 4:3 (2592x1944) at 12 fps
3MP 4:3 (2048x1536) at 15 fps
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
Color: 0.15 lux at 50 IRE, 0.03 lux at 10 IRE,
B/W: 0.03 lux at 50 IRE, 0.006 lux at 10 IRE,
F1.2 (Shutter speed: 1/15 sec)
DC IRIS
CS Mount; External back-focus adjustment
Two-way Audio
G.711 PCM 8kHz, a/μ-law support
External microphone and speaker
AES, AWB, AGC
Exposure Mode: AES / ALC / Flickerless / Manual;
White Balance: Auto / Manual;
Image Settings
Backlight Compensation
Configurable Brightness, Contrast, Hue, Saturation, and Sharpness
Gamma Correction
WDR
Enhanced Digital WDR
DNR
Configurable 3DNR setting
Privacy Zone
Yes, up to 8 privacy zones
Image Orientation
Mirror, Flip
Frequency Control
NTSC(60Hz)/ PAL(50Hz)
Date & Time Stamp
Yes
Intelligent Video & Event Management
Motion Detection
Yes, 3-level sensitivity
Ethernet Detection
Network loss detection
Others
Optimized i-frame (GOP) setting
Events
Motion detection, ethernet detection, external alarm
Event snapshot to remote FTP storage / email recipients;
Event Actions
Edge recording to SD card;
HTTP event query, HTTP event client pulling
Store Category
Event snapshot, Edge recording, Manual Snapshot, Manual Recording
Local Storage
Memory Card Slot
SDXC/SDHC card support
Memory Card Overwrite
Yes
Network
ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,
Protocol
UPnP, IEEE802.1X
Ethernet
10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45
ONVIF
ONVIF
Browser
Internet Explorer, Chrome, Firefox, Safari
39
Security
I/O & Controls
Power
Power LED Indicator
Alarm In/Out
Network
Audio In/Out
Analog Video
System Reboot
Factory Default
Power
Power Requirement
Power Consumption (Max.)
Mechanical
Dimensions(WxDxH)
Weight
Environmental
Operating Temperature
Operating Humidity
Storage Temperature
Regulatory
Approvals
Multiple user access levels with password protection; IP address filtering;
IEEE 802.1X network access control, HTTPS encryption, and digest authentication
3-pin spring terminal/ Female RJ-45 10BASE-T/ 100BASE-TX PoE
System power and status indicator
Terminal block 1 in / 1 relay out(30V, 1A)
RJ-45 with LED Indicator
Terminal block 1 in / 1 out
BNC X1, 1.0Vp-p, 75Ω
Reset x 1
Default x 1, pressing 5 sec for loading factory default
DC 12V & AC 24V ± 10% / PoE (IEEE 802.3af, class 0)
6W
125 x 69 x 56 mm (4.9" x 2.7" x 2.2")
400g (0.88 lb) w/o lens
-10ºC ~ 50ºC (-14ºF ~ 122ºF)
90% RH, non-condensing
-40°C ~ 60°C (-40°F ~ 140°F)
CE, FCC, RoHS
Note: Product specifications and pictures are subject to change without notice.
40
Appendix E: Specifications of IR Bullet Network Camera
Video
Model Type
Sensor Type
Active Pixels
Compression
Streaming
Resolution
Max. Frame Rate
Day/Night
Day/Night Mode
Shutter Time
Minimum Illumination
Video Output
Bit Rate Control
Lens
Lens Type
Focal Length
Focus / Zoom
View Angle
IRIS Control
IR LEDs
LED Quantity
IR Distance
IR Turn on Status
LED Life
Audio
Audio Communication
Compression
Audio In/Out
Image Enhancement
3M Motorized Lens Model
1/3" progressive scan CMOS sensor
2304 x 1536 (HxV)
H.264 / MJPEG
Triple simultaneous streams with multiple video profile
Q X G A ( 2 0 4 8 x 1 5 3 6 ) , 1 0 8 0 P, 1 2 8 0 x 9 6 0 , 7 2 0 P,
SVGA(800x600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
3MP 4:3 (2048x1536) at 15fps;
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
Mechanical (ICR) D/N Control
Auto/ BW/ Color
1/10,000s to 1/7.5s Selectable (60Hz);
1/10,000s to 1/6.25s Selectable (50Hz)
IR LED OFF:
Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE,
F1.2; (Shutter speed: 1/15 sec)
IR LED ON: 0 Lux
NTSC: 720x480 @30fps; PAL: 720x576 @25fps
CBR, VBR
5M Motorized Lens Model
1/3.2" progressive scan CMOS sensor
2592x1944 (HxV)
2592x1944, QXGA(2048x1536), 1080P, 1280x960,
720P, SVGA(800x 600), VGA(640x480), 640x360,
QVGA(320x240), 320x180
5MP 4:3 (2592x1944) at 12 fps
3MP 4:3 (2048x1536) at 15 fps
2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)
IR LED OFF:
Color: 0.15 lux at 50 IRE, 0,03 lux at 10 IRE,
F1.2; (Shutter speed: 1/15 sec)
IR LED ON: 0 lux
Built-in; Varifocal
f=3~9mm, F1.2
Autofocus, motorized / Remote
H: 78°(Wide)~28°(Tele)
DC IRIS
48 pcs (850nm)
30 meters (98ft)
Under 5 lux by auto control
More than 10,000 hours
Two-way Audio
G.711 PCM 8kHz, a/μ-law support
External microphone and speaker
AES, AWB, AGC
Exposure Mode: AES / ALC / Flickerless / Manual;
White Balance: Auto / Manual;
Image Settings
Backlight Compensation
Configurable Brightness, Contrast, Hue, Saturation, and Sharpness
Gamma Correction
WDR
Enhanced Digital WDR
DNR
Configurable 3DNR setting
Privacy Zone
Yes, up to 8 privacy zones
Image Orientation
Mirror, Flip
Frequency Control
NTSC(60Hz)/ PAL(50Hz)
Date & Time Stamp
Yes
Intelligent Video & Event Management
Motion Detection
Yes, 3-level sensitivity
Ethernet Detection
Network loss detection
Others
Optimized i-frame (GOP) setting
Events
Motion detection, audio detection, ethernet detection, external alarm
Event snapshot to remote FTP storage/ email recipients, Edge recording to SD card,
Event Actions
HTTP event query, HTTP event client pulling
Store Category
Event snapshot, Edge recording, Manual Snapshot, Manual Recording
41
Local Storage
Memory Card Slot
Memory Card Overwrite
Network
Protocol
Ethernet
ONVIF
Browser
Security
I/O & Controls
Power
Power LED Indicator
Alarm In/Out
Network
Audio In/Out
Analog Video
System Reboot
Factory Default
Power
Power Requirement
Power Consumption (Max.)
Mechanical
Dimensions(WxDxH)
Weight
Protection
Environmental
Operating Temperature
Operating Humidity
Storage Temperature
Regulatory
Approvals
microSDXC/SDHC card support
Yes
ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,
UPnP, IEEE802.1X
10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45
Yes
Internet Explorer, Chrome, Firefox, Safari
Multiple user access levels with password protection; IP address filtering;
IEEE 802.1X network access control, HTTPS encryption, and digest authentication
All-in-one tail cable out, 2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE
System power and status indicator
Terminal block 1 in / 1 relay out(30V, 1A)
RJ-45 with LED Indicator
Terminal block 1 in / 1 out
1 x composite video out, micro JST
Reset x 1
Default x 1, pressing 5 sec for loading factory default
AC 24V ± 10% / PoE (IEEE 802.3af )
*Arctic power-on support by PoE at -40°C
11.5W
115 x 264 x 110 mm (4.53” x 10.39” x 4.33”)
1600g (3.44 lb)
IP67 Certified, IP68 Compliant, IK10 Compliant
(On-board heating device) -40ºC ~ 50ºC (-40ºF ~ 122 ºF)
90% RH, non-condensing
-20ºC ~ 60ºC (-4ºF ~ 140ºF)
CE, FCC, RoHS
Note: Product specifications and pictures are subject to change without notice.
42
Appendix F: Specifications of Flat Mini Dome Network
Camera
Video
Model Type
Sensor Type
Active Pixels
Compression
Streaming
Resolution
Max. Frame Rate
Day/Night
Day/Night Mode
Shutter Time
Minimum Illumination
Video Output
Bit Rate Control
Lens
Lens Type
Focal Length
View Angle
Audio
Audio Communication
Compression
Audio In/Out
1M Fixed Lens Model
3M Fixed Lens Model
1/4" progressive scan CMOS sensor
1/3" progressive scan CMOS sensor
1280 x 800 (HxV)
2304 x 1536 (HxV)
H.264 / MJPEG
Triple simultaneous streams with multiple video profile
QXGA(2048x1536), 1080P, 1280x960, 720P, SVGA(800x
720P, SVGA(800x 600), VGA(640x480), 640x360,
600), VGA(640x480), 640x360, QVGA(320x240),
QVGA(320x240), 320x180
320x180
3MP 4:3 (2048x1536) at 15 fps
HDTV 720p (1280x720) at 30/25 fps (NTSC/PAL)
2MP Full HD 16:9 (1920x1080) at 30/25 fps (NTSC/PAL)
Mechanical (ICR) D/N Control
Auto/ BW/ Color
1/10,000s to 1/7.5s Selectable (60Hz); 1/10,000s to 1/6.25s Selectable (50Hz)
Color: 0.3 lux at 50 IRE, 0.06 lux at 10 IRE,
Color: 0.4 lux at 50 IRE,0.08 lux at 10 IRE,
B/W: 0.2 lux at 50 IRE, 0.04 lux at 10 IRE,
B/W: 0.3 lux at 50 IRE, 0.07 lux at 10 IRE,
F1.8 (Shutter speed: 1/15 sec)
F1.8 (Shutter speed: 1/35 sec)
NTSC: 720x480 @30fps; PAL: 720x576 @25fps
CBR, VBR
Built-in; Varifocal
f=3.6mm, F1.8
H: 63°
H: 83°
-
Two-way Audio
G.711 PCM 8kHz, a/μ-law support
1 in / 1 out for external microphone/speaker;
Built-in Microphone
-
Image Enhancement
AES, AWB, AGC
Exposure Mode: AES / ALC / Flickerless / Manual;
White Balance: Auto / Manual;
Image Settings
Backlight Compensation
Configurable Brightness, Contrast, Hue, Saturation, and Sharpness
Gamma Correction
WDR
Enhanced Digital WDR
DNR
Configurable 3DNR setting
Privacy Zone
Yes, up to 8 privacy zones
Image Orientation
Mirror, Flip
Frequency Control
NTSC(60Hz)/ PAL(50Hz)
Date & Time Stamp
Yes
Intelligent Video & Event Management
Motion Detection
Yes, 3-level sensitivity
Ethernet Detection
Network loss detection
Others
Optimized i-frame (GOP) setting
Events
Motion detection, ethernet detection
Event snapshot to remote FTP storage/ email
Event snapshot to remote FTP storage/ email
Event Actions
recipients, Edge recording to SD card,
recipients, HTTP event query, HTTP event client pulling
HTTP event query, HTTP event client pulling
Store Category
Event snapshot, Manual Snapshot, Manual Recording
Local Storage
Memory Card Slot
microSDXC/SDHC card support
Memory Card Overwrite
Yes
Network
ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,
Protocol
UPnP, IEEE802.1X
Ethernet
10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45
ONVIF
ONVIF
43
Browser
Security
I/O & Controls
Power
Power LED Indicator
Network
Audio In/Out
Analog Video
System Reboot
Factory Default
Power
Power Requirement
Power Consumption (Max.)
Mechanical
Dimensions(ΦxH)
Weight
Protection
Pan/Tilt Adjustment
Environmental
Operating Temperature
Operating Humidity
Storage Temperature
Regulatory
Approvals
Internet Explorer, Chrome, Firefox, Safari
Multiple user access levels with password protection; IP address filtering;
IEEE 802.1X network access control, HTTPS encryption, and digest authentication
All-in-one tail cable out, Female RJ-45 10BASE-T/100BASE-TX PoE
System power and status indicator
Female RJ-45
Terminal block 1 in / 1 out
1 x composite video out, micro JST
Reset x 1
Default x 1, pressing 5 sec for loading factory default
PoE (IEEE 802.3af ), class 0
7.7W
DC12V/ PoE (IEEE 802.3af, class 0)
8.5W
Φ110mm x 47mm (Φ4.33" x 1.85")
340g (0.75 lb)
IP66 Certified, IP67/IP68 Compliant, IK10 Compliant
3-dimensional spherical lens angle adjustment
-40ºC ~ 50ºC (-40ºF ~ 122 ºF)
90% RH, non-condensing
-40°C ~ 60°C (-40°F ~ 140°F)
CE, FCC, RoHS
Note: Product specifications and pictures are subject to change without notice.
44
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement