Ticket Printer Manual – RS232

Ticket Printer Manual – RS232
2014
TICKET PRINTER MANUAL – RS232
AC Power Version - Part # ASM0282
DC Power Version - Part # ASM0280
Ticket Printer Manual – RS232
Contents
1.
Introduction ....................................................................................................................... 2
2.
What is in the Box? ........................................................................................................... 2
3.
Tools Needed .................................................................................................................... 3
4.
Step By Step Installation Procedure................................................................................ 3
5.
Integrator Printer Setup Instruction Guide ...................................................................... 5
1
Ticket Printer Manual – RS232
1. Introduction
This manual is intended to help you successfully install the Rs232 Serial Printer as an add-on item in the
field. The following instructions will show you a step by step procedure to install the hardware required
for the Printer.
Wiring and software setup will vary from application to application. The attached wiring diagram should
be a guide in selecting the correct wire terminals for your application.
It is critical that you follow all Company and government SAFETY procedures when installing this
component in the field.
After reading this manual and you require any assistance with the installation, wiring, and setup of the
integrator please contact our technical support department.
Belt-Way Scales Inc.
+1 815-625-5573
2. What is in the Box?
The following items are in the box:
DC Version
1. QTY – Printer in a NEMA 4 enclosure
2. 4 QTY – Mounting Tabs
3. 4 QTY - Tab Mounting Screws
4. 1 QTY – Pre-wired DC power cable
(10FT)
5. 1 QTY – Pre-wired RS232 cable (10FT)
1.
2.
3.
4.
5.
2
AC Version
QTY – Printer in a NEMA 4 enclosure
4 QTY – Mounting Tabs
4 QTY - Tab Mounting Screws
1 QTY – Pre-wired AC Power Supply cable (10FT)
1 QTY – Pre-wired RS232 cable (10FT)
Ticket Printer Manual – RS232
3. Tools Needed
The following basic tools will be needed:
1. 1 QTY – Phillips / Star Head Screw Driver
2. 1 QTY - Small Flat Head Screw Driver
3. Lock-Out Tag
4. Correct PPE
5. Basic Mechanics Tool set
4. Step By Step Installation Procedure
The following is a step by step procedure to install the Serial Printer Hardware:
Before you start
1. Disconnect power to the integrator at the
breaker or disconnect panel.
2. Lock out the supply power while installing
the printer.
STEP 1
Mount the printer to the conveyor or machine in the desired location close enough so that the Printer
and power supply cables will reach their connections.
STEP 2
Route the cables so that they are secure and do not get damaged by material or moving parts
STEP 3
Open the box and disconnect power as described
in step 4.
Step 4
(A) IF 110-220 VAC power Supply is INSTALLED
 Remove the AC Supply power Connector
inside the Integrator.
(B) IF 10-30 VDC power Supply is connected
 Remove the DC supply Power Connector
inside the Integrator.
When removing
the connector use
the screw driver as
shown above to
avoid pin damage.
3
Ticket Printer Manual – RS232
STEP 5
1. Route the print cable and DC power cable through the cord grip connectors on the integrator.
The AC version only needs the printer cable (RS232) routed through the cord grip connectors.
2. Connect the Print Cable (RS232) and Power Cable as shown for the AC or Dc version.
STEP 6
Connect RS232 and Power cables inside the integrator box as shown for your version.
DC Version
AC Version
RS232 CABLE
RS232 CABLE
AC POWER CABLE
DC POWER CABLE
The power cable needs to be connected in the
same connector as the DC supply wires. Make
sure source power is disconnected to avoid
shorting and damage.
STEP 7
1. Reconnect the power connectors that were disconnected in STEP 4 and turn breaker
back ON.
2. Turn Printer Power on with switch on printer face plate.
4
Ticket Printer Manual – RS232
STEP 8
Close the integrator door
STEP 9
Follow setup procedure below to setup the data you need printed on your tickets.
Navigation Tip
Press the MENU key.
Navigate to the DEVICE SETUP icon and press ENTER key
FOLLOW THE STEP BY STEP SCREEN INSTRUCTIONS
Press the BACK key go back to the previous screen
Some data fields are also under the Administration Menu
Press the MENU key.
Navigate to the ADMINISTRATION icon and press ENTER key
5. Integrator Printer Setup Instruction Guide
The following information will help you decide how to setup the Integrator for your application needs:
Printer
Setup Ticket:
Enter the following:
 Company Name
 Address
 Phone Number
Tickets On / Off - Enable ticket printing.
Printer Type: Setup parameters for your
Printer.
Default settings:
 Belt-Way printer
 RS232 port
 Baud rate - 9600
 Data Bits - 8
 Stop Bits - 1
 Flow Control – None
Press the PRINT key to print the ticket.
Administration Settings
 Scale Name
 Plant Name
 Product name
 Current date
 Current Time
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement