THE POWER ADAPTER CABLE Datalogic Memor™ Power Adapter Cable Powering the dock/ Memor in your vehicle. B The Datalogic Memor™ Power Adapter Cable allows powering the Datalogic Memor™ mobile computer (either directly or through the Powered Vehicle Dock). Figure 2b THE PACKAGE A) The Power Adapter Cable package includes the following items: When the Power Adapter Cable is powered, the green LED lights up. B 1. Plug in the supplied Power Adapter Cable into your vehicle’s cigarette lighter or 12V or 24V power source; 2. insert the Power Adapter Cable output connector: A Figure 2a A POWERING THE MEMOR™ POWERED VEHICLE DOCK Green LED B) a) in the power port at the right bottom of the dock (see figure 3a). When the dock is powered, the green LED lights up; b) in the port at the bottom of the mobile computer (see figure 3b). Fuse (2.5A 250V) The Power Adapter Cable fuse can be easily replaced by unscrewing the ring nut and removing the cap (see Figure 2a). Figure 3a C Figure 3b Make sure your vehicle’s output voltage is between 10V to 32V, and is capable of supporting a 2000mA current drain. If you have any concerns regarding this, refer to CAUTION your vehicle owner’s manual. When the Power Adapter Cable is connected to the Memor, it is recommended not to lift the mobile computer by the Power Adapter CAUTION Cable. Figure 1 A) B) C) Power Adapter Cable CLA Battery Female Adapter Fuse Holder 852000491 (Rev. A) Powering the dock/ Memor using the Battery Female Adapter 2. Plug in the cigarette lighter adapter into the Battery Female Adapter: For connection to the vehicle power source through the Battery Female Adapter, it is necessary to prepare the power cable termination to connect the dock to the vehicle power source. − Red wire: connect to a V+ (10 to 32 Vdc) vehicle power source; − Black wire: connect to the vehicle ground wire or chassis ground. In this case, it is mandatory to use the slow-blow 8A 250V (with holder) supplied. Figure 6 1. Verify that the fuse is contained within the holder, then splice it to the end of the red wire of the cable. Make the distance between fuse holder and power connection point as short as possible and apply a caution label on the fuse holder. 3. Insert the Power Adapter Cable output connector in the dock/Memor power port (see the previous section). Once the power cable termination has been completed, it is possible to connect the dock to the vehicle power. To avoid battery waste, it is recommended to connect the dock to a power connection point switched by the ignition key. NOTE When connecting the Battery Female Adapter cable to the power connection point, ensure that it does not pass by sharp or very hot CAUTION surfaces. Figure 4 Red Wire Battery Charging The Power Adapter Cable provides battery charging for the Datalogic Memor™ when powered. Figure 5 TECHNICAL FEATURES Datalogic Memor™ Power Adapter Cable Electrical Features Power Supply from 10 to 32 VDC Consumption (with Max. 1.15 A mobile computer) Max. 38 mA Quiescent Consumption (CLA + Dock no load) Max. 32 mA Quiescent Consumption (CLA only no load) Indicators Power on LED (green) Charge Time Li-Ion Battery: max. 4 hours Environmental Features Working 0° to +50 °C / +32° to +140 °F Temperature* Storage -20° to +70 °C / -4° to +158 °F Temperature Humidity 90% non condensing Sinusoidal 14 mm @ 2 to 10Hz; 1.5 mm @ 13 Vibration to 55 Hz; 2 gn @ 70 to 200 Hz; 2 hours on Resistance each axis EN 60068-2-6 Random Vibration Frequency Range 5-1000 Hz; acceleration RMS: 3.1 g; initial Resistance slope: 26 dB/octave 5-10 Hz, EN 60068-2-64 final slope: -3 dB/octave 10-1000 Hz; 1 hour on each axis Bump Resistance 25 G; 6 ms; 500 up & 500 down EN 60068-2-29 bumps on each axis Shock Resistance 30 G; 11ms; 3 shocks on each axis EN 60068-2-27 Mechanical Features Weight (CLA + 180 g / 7.2 oz Adapter) * The Datalogic Memor™ will charge its installed battery when power is applied to the Power Adapter Cable. NOTE Battery must be charged at a temperature ranging from 0° to +40 °C. For the GSM models the maximum recommended temperature is +35°C. At higher values the charging may slow down. Close to the limits of the working temperature, some display and/or battery performance degradation may occur.