SD-34VLSL
DVD PLAYER &
VIDEO CASSETTE RECORDER
SD-34VLSL
OWNER’S MANUAL
R
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
©2004 Toshiba Corporation
This device does not tape-record copy protected DVD Video Discs.
Notes on Copyrights:
CAUTION
It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some discs.
When recording and playing the pictures of these
discs picture noise will appear. This product incorporates copyright protection technology that is protected
by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this
copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning: To reduce the risk of electric
shock, do not remove the cover or back
of this product. There are no user-serviceable parts inside. Refer servicing to
qualified service personnel.
Warning: To reduce the risk of fire or
electric shock, do not expose this product to dripping or splashing water, rain,
or moisture. Do not place objects filled
with water such as vases, on the product.
Warning: This digital video disc player
employs a laser system. Use of controls,
adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation
exposure.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS ECOMMENDED
THAT THE USER SWITCH THE CONNECTION TO
THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE
ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p
DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
SERIAL NUMBER:
Warning: To prevent direct exposure to
laser beam, do not open the enclosure.
Visible laser radiation may be present
when the enclosure in opened.
You can find the serial number on the back of the
unit. This number is unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record
of your purchase.
Warning: Never stare directly into the
laser beam.
Model No. ______________________________
Serial No. ______________________________
Caution: Do not install this product in a
confined space such as a book case or
similar unit.
Date of Purchase_________________________
This product is manufactured to comply
with the radio interference requirements
of EEC DIRECTIVE 89/336/EEC,
93/68/EEC and 73/23/EEC.
1-7
SOME DOS AND DON'TS ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet international safety standards but,
like any electrical equipment, care must be taken if you are to obtain the best results and safety is to
be assured. So, please read the points below for your own safety. They are of a general nature,
intended to help you with all your electronic consumer products and some points may not apply to
the goods you have just purchased.
**************
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and inter- connections between the pieces of equipment) are properly made and in accordance with the manufacturer's instructions. Switch off and withdraw the mains plug before making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your
equipment.
DO be careful with glass panels or doors on equipment
**************
DON'T remove any fixed cover as this may expose dangerous voltages.
DON'T obstruct the ventilation openings of the equipment with items such as newspapers, tablecloths, curtains, etc. Overheating will cause damage and shorten the life of the equipment.
DON'T allow electrical equipment to be exposed to dripping or splashing, or objects filled with liquids, such as vases, to be placed on the equipment.
DON'T place hot objects or naked flame sources such as lighted candles or nightlights on, or close
to equipment. High temperatures can melt plastic and lead to fires.
DON'T use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety
always fit the manufacturer's approved stand or legs with the fixings provided according to the
instructions.
DON'T use equipment such as personal stereos or radios so that you are distracted from the
requirements of traffic safety. It is illegal to watch television whilst driving.
DON'T listen to headphones at high volume, as such use can permanently damage your hearing.
DON'T leave equipment switched on when it is unattended unless it is specifically stated that it is
designed for unattended operation or has a stand-by mode. Switch off using the switch on the
equipment and make sure that your family know how to do this. Special arrangements may need to
be made for infirm or handicapped people.
DON'T continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way -switch off, withdraw the mains plug and consult your dealer.
ABOVE ALL
---NEVER let anyone especially children push anything into holes, slots or any other opening
in the case - this could result in a fatal electrical shock;
---NEVER guess or take chances with electrical equipment of any kind
---it is better to be safe than sorry!
*************
1-8
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .5
Symbol Used in this Manual . . . . . . . . . . . . . . . . . .5
About the
Symbol Display . . . . . . . . . . . . . . . . .5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Handling Discs . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Storing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Moisture Condensation . . . . . . . . . . . . . . . . . . . .5
Types of Playable Discs . . . . . . . . . . . . . . . . . . . . . .6
Regional code . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Selecting the Viewing Source . . . . . . . . . . . . . . . . .6
Disc-related terms . . . . . . . . . . . . . . . . . . . . . . . . . .7
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Display Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Preparation . . . . . . . . . . . . . . . . . . . . . . . . .13
Connecting to a TV and Decoder (or Set Top Box) . .13
Connecting to Optional Equipment . . . . . . . . . . . .14
Tuning in a video channel on your TV . . . . . . . . . .15
Using your DVD+VCR for the very first time . . . . .15
Setting the clock Manually . . . . . . . . . . . . . . . . . . .16
To set the colour system . . . . . . . . . . . . . . . . . . . .16
To set the RF OUT sound system . . . . . . . . . . . . .16
How to use the main menu . . . . . . . . . . . . . . . . . .17
Tuning in TV Stations Automatically . . . . . . . . . . . .17
Tuning in TV Stations Manually . . . . . . . . . . . . . . .18
Changing the order of TV Stations . . . . . . . . . . . . .19
Deleting TV Stations . . . . . . . . . . . . . . . . . . . . . . . .19
DVD On-Screen Display . . . . . . . . . . . . . . . . . . . . .20
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
General Operation . . . . . . . . . . . . . . . . . . . . . . .21
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
• Menu Language . . . . . . . . . . . . . . . . . . . . . . . .21
• Disc Audio / Subtitle / Menu . . . . . . . . . . . . . .21
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
• TV Aspect . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
• Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . .21
• Progressive Scan . . . . . . . . . . . . . . . . . . . .21-22
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
• Dolby Digital / DTS / MPEG . . . . . . . . . . . . . . .22
• Sample Freq. (Frequency) . . . . . . . . . . . . . . . . .22
• Dynamic Range Control (DRC) . . . . . . . . . . . .22
• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
• PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
• Auto Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
• B.L.E.(Black Level Expansion) . . . . . . . . . . . . . .23
• DivX(R) VOD . . . . . . . . . . . . . . . . . . . . . . . . . .23
LOCK (Parental Control) . . . . . . . . . . . . . . . . . .24
• Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
• Password (Security Code) . . . . . . . . . . . . . . . . .24
• Country Code . . . . . . . . . . . . . . . . . . . . . . . . .24
Operation . . . . . . . . . . . . . . . . . . . . . . . . . .25
Playing a tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
CM (Commercial Message) Skip . . . . . . . . . . . .25
OPR (Optimum Picture Response) . . . . . . . . . . .25
One-touch Timer Recording (OTR) . . . . . . . . . . . . .26
Timer recording using On Screen Display . . . . . . . .27-28
SHOWVIEW Programming . . . . . . . . . . . . . . . . . . . . .29
Playing a DVD and Video CD . . . . . . . . . . . . . . . . .30
Playback Setup . . . . . . . . . . . . . . . . . . . . . . . . . .30
General Features . . . . . . . . . . . . . . . . . . . . . . . . . .30
Moving to another TITLE/GROUP . . . . . . . . . . . .30
1-9
Moving to another CHAPTER/TRACK . . . . .
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Audio Channel . . . . . . . . . . . .
Still Picture and Frame-by-Frame Playback . . .
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . .
One Touch Replay . . . . . . . . . . . . . . . . . . . . .
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . .
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . .
Time Search . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Video Mode . . . . . . . . . . . . . . . . . .
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Marker Search . . . . . . . . . . . . . . . . . . . . . . .
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . .
Special DVD Features . . . . . . . . . . . . . . . . . . . .
Checking the contents of DVD discs: Menus . .
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Audio Language . . . . . . . . . . .
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVD Audio Discs . . . . . . . . . . . . . . . . . . . . . . .
Moving to another GROUP . . . . . . . . . . . . . .
Viewing another PAGE . . . . . . . . . . . . . . . . .
Playing an Audio CD or MP3/WMA Disc . . . . .
Audio CD and MP3/WMA Disc Features . . . . .
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving to another Track . . . . . . . . . . . . . . . .
Repeat Track/All/Off . . . . . . . . . . . . . . . . . . . .
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . .
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . .
Programmed Playback . . . . . . . . . . . . . . . . . . .
Repeat Programmed Tracks . . . . . . . . . . . . . . . .
Erasing a Track from Program List . . . . . . . .
Erasing the Complete Program List . . . . . . .
Viewing a JPEG Disc . . . . . . . . . . . . . . . . . . . . .
Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . .
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving to another File . . . . . . . . . . . . . . . . .
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To rotate picture . . . . . . . . . . . . . . . . . . . . . .
To listen to MP3/WMA music watching picture
Playing a DVD VR format Disc . . . . . . . . . . . . .
Playing a DivX Movie Disc . . . . . . . . . . . . . . . .
Additional Operation with tape . . . . . . . . . . . . .
Hi-Fi Stereo Sound System (NIC) . . . . . . . . .
Blank Search . . . . . . . . . . . . . . . . . . . . . . . .
On Screen Display(F.OSD) . . . . . . . . . . . . . .
Tape Counter Memory Stop . . . . . . . . . . . . . .
Video Doctor (Self-Diagnosis) . . . . . . . . . . . .
Wide Screen Compatibility 16:9 . . . . . . . . . . .
To set the decoder . . . . . . . . . . . . . . . . . . . .
Copying from DVD to VCR . . . . . . . . . . . . . .
Recording from another video recorder . . . . .
Video Head Cleaning . . . . . . . . . . . . . . . . . .
. . .30
. . .30
. . .30
. . .31
. . .31
. . .31
. . .31
. . .31
. . .31
. . .31
. . .32
. . .32
. . .32
. . .32
. . .32
. . .33
. . .33
. . .33
. . .33
. . .33
. . .33
. . .33
. . .34
. . .34
. . .34
. . .35
. . .36
. . .36
. . .36
. . .36
. . .36
. . .36
. . .36
. . .36
. . .37
. . .37
. . .37
. . .37
. . .38
. . .38
. . .38
. . .38
. . .38
. . .38
. .38
. . .39
. . .40
. . .41
. . .41
. . .41
. . .41
. . .41
. . .42
. . .42
. . .43
. . .43
. . .43
. . .43
Reference . . . . . . . . . . . . . . . . . . . . . . . . . .44
Language Codes
Country Codes .
Troubleshooting
Specifications . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .44
. . . . . . . . . . . . . . . . . . . . . . . . . . .44
. . . . . . . . . . . . . . . . . . . . . . . .45-46
. . . . . . . . . . . . . . . . . . . . . . . . . . .47
Introduction
This manual provides information on the operation
and maintenance of your DVD+VCR. Should the unit
require service, contact an authorized service location.
About the
Symbol Display
“
” may appear on your TV display during operation and indicates that the function is not permitted by
this unit or the disc.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
Symbol Used in this Manual
The lightning flash symbol alerts you to the
presence of dangerous voltage within the
product enclosure that may constitute a risk
of electric shock.
The exclamation point alerts you to the presence of important operating and maintenance
/ servicing instructions.
Indicates hazards likely to cause harm to the
unit itself or other material damage.
Storing Discs
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and
never leave it in a parked car exposed to direct sunlight.
Note:
Cleaning Discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
Indicates special notes and operating features.
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols is applicable only to the disc represented by the
symbol.
DVD-V
DVD and finalized DVD±R/RW
DVD-A
DVD Audio discs
VCD
Video CDs
CD
Audio CDs
MP3
MP3 Discs
WMA
WMA Discs
JPEG
JPEG Discs
DivX
DivX Discs
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Moisture Condensation
Never operate the DVD+VCR immediately after moving it from a cold location to a warm location. Leave it
for two or three hours without operating it. If you use
the DVD+VCR in such a situation, it may damage
discs/tapes and internal parts.
1-10
Introduction
To ensure proper use of this product, please read this
owner’s manual carefully and retain for future reference.
Types of Playable Discs
Regional code
This DVD+VCR is designed and
manufactured for playback of region
“2” encoded DVD software. This unit
can play only DVD discs labeled “2”
or “ALL”.
DVD video discs
(8 cm / 12 cm disc)
DVD audio discs
(8 cm / 12 cm disc)
2
ALL
Notes on Regional Codes
Video CD (VCD)
(8 cm / 12 cm disc)
• Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This number must match your DVD+VCR’s regional code or
the disc cannot play.
Audio CD
(8 cm / 12 cm disc)
In addition, this unit plays DivX file, DVD -R, DVD +R,
DVD -RW, DVD +RW, SVCD, and CD-R / CD-RW that
contains audio titles, MP3, WMA, and/or JPEG files.
This indicates a product feature that is
capable of playing DVD-RW discs
recorded with Video Recording format.
Notes:
• Refer to page 7 for more informations on disc-related terms.
• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD -R, DVD +R,
DVD -RW, DVD +RW) disc itself, some CD-R/RW
(or DVD -R, DVD +R, DVD -RW, DVD +RW) discs
cannot be played on the unit.
• If you try to play a DVD with a different region code
from your player, the message “Check Regional
Code” appears on the TV screen.
Selecting the Viewing Source
You must select one of your output sources (DVD
or VCR) to view on the TV screen.
• If you want to view DVD deck output source:
Press DVD until DVD indicator in the display window
lights and output source of DVD deck is viewed on the
TV screen.
• If you want to view VCR deck output source:
Press VCR until VCR indicator in the display window
lights and output source of VCR deck is viewed on the
TV screen.
Notes:
• If you insert a disc while the DVD+VCR is in the
• Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
• Do not use irregularly shaped CDs (e.g., heartshaped or octagonal) since they may result in malfunctions.
Notes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs
may be intentionally programmed by software manufacturers. This unit plays DVDs and Video CDs
according to disc content designed by the software
manufacturer, therefore some playback features may
not be available or other functions may be added.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories.
DTS and DTS Digital Out are trademarks of
Digital Theater Systems, Inc.
1-11
VCR mode, the DVD+VCR will switch to DVD
mode automatically.
• If you insert a cassette tape without prevention
tab while the DVD+VCR is in the DVD mode, the
DVD+VCR will switch to VCR mode automatically.
DVD ±R / DVD ±RW
DVD -R and DVD +R are two different standards for
recordable DVD drives and discs. This format allows
information to be recorded onto the DVD disc only
once. DVD +RW and DVD -RW are two standards for
re-writable media, meaning the DVD content can be
erased and re-recorded. Single-sided discs can hold
4.38 Gigabytes and double-sided discs hold twice as
much. This player can only playback single sided
recordable discs.
VCD (Video CD)
A VCD holds up to 74 minutes (650 MB disc) or 80
minutes (700 MB disc) of MPEG-1 full-motion video
along with quality stereo sound.
MPEG
MPEG is an international standard for video and
audio compression. MPEG-1 is used in encoding
video for VCD and provides for multichannel surround
sound coding such as PCM, Dolby Digital, DTS and
MPEG audio.
MP3
MP3 is a popular compression format used for digital
audio files that yields very high near-CD quality.
WMA
Windows media audio file. A type of coding / decoding developed by Microsoft Corp.
JPEG
Joint Pictures Expert Group. JPEG is a compressed
file format that allows you to save images with no limit
on the number of colors.
DivX
DivX is the name of a revolutionary new video codec
which is based on the new MPEG-4 compression
standard for video.You will be able to play DivX
movies using this player .
1-12
PBC: Playback Control (Video CD only)
Playback control is available for Video CD (VCD) version 2.0 disc formats. PBC allows you to interact with
the system via menus, search functions, or other typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included
in the disc. Video CDs not equipped with PBC
(Version 1.1) operate in the same way as audio CDs.
Title (DVD video discs only)
A title is generally a distinct section of a DVD disc.
For example the main feature could be title 1, a documentary describing how the film was made could be
title 2, and cast interviews could be title 3. Each title
is assigned a reference number enabling you to
locate it easily.
Group (DVD audio discs only)
The main audio content or accompanying feature
content or additional feature content, or music album.
Each group is assigned a group reference number
enabling you to locate it easily.
Chapter (DVD video discs only)
A chapter is a segment of a title such as a scene in a
film or one interview in a series. Each chapter is
assigned a chapter number, enabling you to locate
the chapter you want. Depending on the disc, chapters may not be recorded.
Scene (VCD)
On a video CD with PBC (playback control) functions,
moving pictures and still pictures are divided into sections called “scenes”. Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want. A scene is composed of one or several tracks.
Track
A distinct element of audiovisual information, such as
the picture or sound track for a specific language
(DVD), or a musical piece on a video or audio CD.
Each track is assigned a track number, enabling you
to locate the track you want. DVD discs allow one
track of video (with multiple angles) and several
tracks of audio.
Introduction
Disc-related terms
Front Panel
OPEN/CLOSE
Opens or closes the disc tray.
Display window
Shows the current status of the DVD+VCR.
Disc Tray (DVD deck)
Insert a disc here.
Cassette Compartment (VCR deck)
Insert a video cassette here.
Remote Sensor
Point the DVD+VCR remote control here.
ON/STANBY
Switches the
DVD+VCR ON
and OFF.
EJECT
Ejects the tape in the VCR deck.
AV3
DVD/VCR indicator
Indicates the active deck.
STOP (■)
Stops playback of
disc.
PLAY (w)
Starts playback of a
disc in the DVD deck.
SKIP (B/F)
- Skip to beginning of current chapter or track, press twice in quick successions to go to previous chapter
or track.
- Skip to next chapter or track.
Press and hold button for about two
seconds to search backward or forward.
REC
To record normally or to
activate One-touch Timer
Recording by repeated
presses.
STOP (■)
Stops playback of tape.
PLAY (w)
Starts playback of a tape in the VCR deck.
REW
Rewinds the tape during the STOP
mode or for fast reverse picture search.
FWD
Advances the tape during the STOP mode
or for fast forward picture search.
AV3 (VIDEO IN/AUDIO IN (Left/Right))
Connect to the audio/video output of an external source (Audio
system, TV/Monitor, Another VCR).
1-13
Display Window
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
Indicates when the Progressive scan is active.
Indicates repeat mode.
DVD+VCR is in timer recording or a timer
recording is programmed.(VCR part only)
A cassette is in the VCR deck.
The VCR deck is selected.
DVD
[P]
VCR
REC
TV
Lights when TV mode is active (see page 26).
DVD+VCR is Recording.
(VCR part only)
Indicates total playing time, elapsed time, remaining time or
current deck status (Playback, Pause, etc).
1-14
Introduction
The DVD deck is selected.
Remote Control
DVD/VCR select button
Select the output source (DVD or VCR) to view on the TV screen.
0-9 numerical buttons
Selects numbered options in a menu.
INPUT SELECT
To select the VCR deck’s source (Tuner, AV1, AV2 or AV3).
TOP MENU
Displays the disc’s Title menu, if available.
MENU
Accesses menu on a DVD disc.
RETURN
Removes the setup menu.
ZOOM
Enlarges video image.
ANGLE
Selects a DVD camera angle if available.
SUBTITLE
Selects a subtitle language (DVD).
AUDIO
Selects an audio language (DVD) or an audio channel (VCD).
INSTANT REPLAY
Replays through 10 seconds of DVD playback.
SKIP B
Skip to beginning of current chapter or track,
press twice in quick successions to go to previous chapter or track.
SKIP F
Skip to next chapter or track.
SET UP, VCR MENU
Accesses or removes DVD setup menu and VCR menu.
W/w/v/V (left/right/up/down)
- Selects an option in the menu
- PR/TRK (+/-): Selects channel of VCR. Adjusts manually the
tape’s picture onscreen.
ENTER/OK
- Acknowledges menu selection.
- Displays functions on the TV screen.
SEARCH
Displays MARKER SEARCH menu.
Remote Control Battery installation
Distance: About 23 ft (7 m) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of the
remote sensor
AAA
AAA
Remote Control Operation
Point the remote control at the remote sensor and
press the buttons.
Detach the battery cover on the rear of
the remote control, and insert two
(R03/AAA) size batteries with
and
aligned correctly.
Do not mix old and new batteries and never
mix different types of batteries such as standard, alkaline, etc.
1-15
Remote Control
EJECT, OPEN/CLOSE
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
TV/VCR
To view channels selected by the VCR tuner or by the TV tuner.
COUNTER RESET, CLEAR
- Resets tape counter to M 0:00:00.
- Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
BLANK SEARCH
Finds end points of recording.
CLK/CNT, DISPLAY
Accesses On-Screen display.
Switches among the clock, tape counter and tape remaining modes
on the display.
PLAY
Starts playback.
REW
- Rewinds the tape during the STOP.
- To fast reverse picture search.
FWD
- Advances the tape during the STOP.
- To fast forward picture search.
SLOW
Forward slow playback.
STOP
Stops playback.
PAUSE/STILL, PAUSE/STEP
- Pause playback or recording.
- Press repeatedly for frame-by-frame playback during pause.
REPEAT
Repeat chapter, track, title, group, all.
MARKER
Marks any point during playback.
AUTO TRK
Adjusts automatically the tape’s picture onscreen.
A-B RPT (REPEAT), SP/LP
- Repeats sequence.
- Selects recording speed of the tape.
RANDOM, INSTANT SKIP
- Plays tracks in random order.
- Fast forwards picture search through 30 seconds of recording.
SHOWVIEW/PROGRAM
- To display the programme menu for SHOWVIEW programming.
- Accesses or removes Program menu.
REC/OTR
Records normally or activates One- touch Timer Recording with
repeated presses.
1-16
Introduction
I/ (POWER)
Switches DVD+VCR ON and OFF.
Rear Panel
AERIAL
Connect the aerial using this jack.
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr)
(DVD EXCLUSIVE OUT)
Connect to a TV With Y Pb Pr inputs.
AUDIO OUT (Left/Right) (DVD EXCLUSIVE OUT)
Connect to an amplifier, receiver or stereo system.
EURO AV2 DECODER
Connect to pay-TV decoder, Set Top Box or another
video recorder.
AC Power Cord
Connect to a power source.
OPTICAL (DVD EXCLUSIVE OUT)
(Digital audio out jack)
Connect to digital (optical) audio equipment.
S-VIDEO OUT (DVD EXCLUSIVE OUT)
Connect to a TV With S-Video input.
EURO AV1 AUDIO/VIDEO (VCR IN+OUT/DVD OUT)
Connect to your TV set or another video recorder.
COAXIAL (DVD EXCLUSIVE OUT)
(Digital audio out jack)
Connect to digital (coaxial) audio equipment.
RF.OUT (DVD/VCR OUT)
Connect to your TV using this jack.
Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
1-17
Tips:
S-Video connection
• Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
unit.
1. Connect the S-VIDEO OUT jack on this unit to the
S-Video in jack on the TV using the S-Video cable
(not supplied).
• Please refer to the manuals of your TV, Stereo System or
other devices as necessary to make the best connections.
• For better sound reproduction, connect this unit’s AUDIO
OUT jacks to the audio in jacks of your amplifier, receiver,
stereo or audio/video equipment. See “Connecting to
Optional Equipment” on page 14.
2. Connect the Left and Right AUDIO OUT (DVD
EXCLUSIVE OUT) jacks of this unit to the audio
left/right in jacks on the TV using the audio
cables.
Component (Color Stream®) / Progressive
Scan (ColorStream® pro) Video connection
(DVD EXCLUSIVE OUT)
Caution:
• This DVD+VCR only support PAL system (refer to VCR
part only).
• Make sure this unit is connected directly to the TV. Set the
TV to the correct video input channel.
• Do not connect this unit’s AUDIO OUT jack to the phono
in jack (record deck) of your audio system.
1. Connect the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT (DVD EXCLUSIVE OUT)
jacks on the DVD+VCR to the corresponding in
jacks on the TV using an Y Pb Pr cable (not supplied).
2. Connect the Left and Right AUDIO OUT (DVD
EXCLUSIVE OUT) jacks of the DVD+VCR to the
audio left/right in jacks on the TV using the audio
cables.
Connecting to a TV and
Decoder (or Set Top Box)
• Make one of the following connections, depending
on the capabilities of your existing equipment.
Notes:
• RGB signal is only exclusive for DVD playback.
Basic connection (AV)
1. Connect the EURO AV1 AUDIO/VIDEO on the
rear panel of this unit to the SCART input socket
on the TV using a SCART lead (not supplied).
For TV without SCART, connect the yellow VIDEO
OUT jack and DVD/VCR AUDIO OUT jacks of this
unit to the TV.
• If your television is a high-definition or “digital ready” television, you may take advantage of the DVD+VCR’s progressive scan output for the highest video resolution possible.
• Set the Progressive Scan to “On” on the setup menu for
progressive scan signal, see page 22.
• When you use Component Video signal (interlace mode),
set the Progressive Scan to “Off” on the setup menu.
2. Some TV broadcasters transmit encoded television signals which you can only see with a purchased or rented decoder. You can connect such
a decoder (descrambler) to this unit.
• If you set Progressive Scan to ON in error, you must reset
the DVD+VCR. First, remove the disc in the DVD+VCR.
Next, press STOP (■) and hold it for five seconds before
releasing it. The video output will be restored to the standard setting, and a picture will once again be visible on a
conventional analog TV or monitor.
Basic connection (RF)
• If the TV has an S-video input, connect the DVD+VCR
with the S-video cable. When using an S-video cable, do
not connect the yellow video cable.
1. Connect the RF antenna cable from your indoor/
outdoor antenna to AERIAL jack on the rear
panel of this unit.
2. Connect the supplied RF antenna cable from the
RF.OUT (DVD/VCR OUT) jack on the rear panel
of this unit to your television’s Antenna Input.
1-18
Introduction
Preparation
Digital Multi-channel sound
Rear of this unit (Component/Progressive scan Video connection)
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your unit (MPEG 2, Dolby
Digital and DTS). Check the receiver manual and the
logos on the front of the receiver.
Warning:
Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream
is selected.
Rear of TV
AERIAL
VIDEO IN
COMPONENT/PROGRESSIVE SCAN VIDEO INPUT
Pr
Pb
Y
AUDIO INPUT
L
Notes:
• If the audio format of the digital output does not
match the capabilities of your receiver, the receiver
will produce a strong, distorted sound or no sound
at all.
SCART INPUT
R
S-VIDEO OUT
Decoder or Set Top Box
• Six Channel Digital Surround Sound via digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
• To see the audio format of the current DVD in the
On-Screen Display, press AUDIO.
Rear of this unit
Rear of this unit (Basic connection)
Connecting to Optional
Equipment
2 channel analog stereo or Dolby Surround connection.
Connecting to an amplifier equipped with
two channel analog stereo or Dolby
Surround.
Connect the Left and Right DVD/VCR AUDIO OUT or
AUDIO OUT (DVD EXCLUSIVE OUT) jacks on this
unit to the audio left and right in jacks on your amplifier, receiver or stereo system, using the audio cables.
Connecting to an amplifier equipped with
two channel digital stereo (PCM) or to an
Audio/ Video receiver equipped with a multichannel decoder (Dolby Digital™, MPEG 2 or
DTS)
1. Connect one of this unit’s DIGITAL AUDIO OUT
jack (COAXIAL or OPTICAL) to the corresponding in jack on your amplifier. Use an optional digital (optical or coaxial) audio cable.
2. You will need to activate this unit’s digital output.
(See “AUDIO” on page 22).
1-19
Digital multi-channel
connection
DVD exclusive out
L
R
AUDIO INPUT
Amplifier (Receiver)
COAXIAL
DIGITAL INPUT
OPTICAL
DIGITAL INPUT
Notes:
•
•
The output frequency of this video recorder
(VCR) is set at UHF channel 60. If channel 60
is already used by another TV station, or if the
picture is distorted, you can change the
transmitter channel of your DVD+VCR. Stages
5 ~ 8 will show you how to change the output
frequency of your DVD+VCR.
Your TV receives signals from the video
recorder (VCR) like another TV station. You
have to select a channel number on your TV
and tune it in so that you may watch video
tapes. If you have used a SCART then your
TV should already have a dedicated video
channel built into it, usually called AV.
1. Make sure that you have correctly installed your
DVD+VCR as described earlier in this book.
Press I/
to turn on your DVD+VCR.
Turn on your TV.
RF CHANNEL
P
RSET
60
i
7. Use b or FWD f to select another video
channel. You may select any channel number
between 22 and 68.
You can also set it to “OFF” if there is any
interference when your TV is connected to the
VCR with a SCART lead.
8. Select a TV channel number on which you wish to
watch video’s.
Press ON/STANDBY I/ on the front of your
DVD+VCR when you have finished.
Tune this channel so that a bright blue screen
appears. Store this channel on your TV.
Notes:
2. Insert a pre-recorded video tape into your
DVD+VCR and press PLAY w on the remote control.
Select a TV channel number on which you wish to
watch video’s.
Don’t worry if you don’t have a video-tape to play
at this stage! If you switch your DVD+VCR on and
continue stages 3 ~ 4, instead of seeing video
playback tune your TV until you see a bright blue
screen.
3. Tune this channel until the video picture is sharp
and the sound is clear.
If you have used a SCART or AUDIO and VIDEO
cables you will not have to tune your TV, simply
select the AV channel. The AV channel is already
pre-tuned for optimum video playback on your TV.
Make sure that you have correctly installed your
DVD+VCR and successfully tuned in a dedicated video channel on your TV. If you do not tune
in a dedicated video channel on your TV you
will be unable to view and record video tapes!
Using your DVD+VCR for the
very first time
The following picture will be displayed on the TV
screen when you have just connected your DVD+VCR
for the very first time.
4. Store this channel on your TV.
You will need to look at the TV instruction book if
you do not know how to do this.
5. Only carry out stages 5 ~ 8 if you cannot
obtain clear video playback as described in
stages 1 ~ 4. Select a TV channel number on
which you wish to watch video’s.
Make sure that your DVD+VCR is in standby
pressing I/ on the remote control (only the clock
will be displayed).
1-20
A
N
Pr-12
ACMS
B CH
NL
P
D DK E F I
S SF ANDERE
OK i
To activate tuning of TV stations, please follow stages
3 to 4 of “Tuning in TV Stations Automatically” in page
17.
Preparation
6. Press REW b or FWD f on the front of
your DVD+VCR for more than 4 seconds.
RF60 will appear in the display window.
The following picture will be displayed on the TV
screen.
Tuning in a video channel on
your TV
Setting the clock Manually
To set the colour system
The clock in your DVD+VCR controls time and
date settings for your DVD+VCR.
The clock is set automatically during ACMS
(Automatic Channel Memory System) when
your DVD+VCR detects a channel that broadcasts a Teletext signal. If the broadcast signal is
weak the clock will not be set and will require
setting manually.
1. Press VCR MENU.
1. Press VCR MENU.
Press W or w to select TIME DATE.
Press ENTER/OK.
The auto adjust mode can be set to “OFF” by
pressing v or V if you want to set the time
manually.
Press ENTER/OK.
AUTO
--
2. The main menu will appear on the TV screen.
3. Press W or w to select the SYSTEM and press
ENTER/OK.
4. Press v or V to select according to the
COLOUR system used.
REC
f OSD
ON
OFF
AUTO
PSET
ACMS
R
Pr-12
1 2
TIME
DATE
PAL
MESECAM
16:9 DECO+
-
DER
4:3
VCR
SYSTEM
Dr.
NIC
SYSTEM
i
OPR
5. Press VCR MENU to remove the menus from the
TV screen.
ADJUST : ON
To set the RF OUT sound
system
1 2
TIME
DATE
OK i
1. Press VCR MENU.
HH MM
-- : - -
DD MM
YY
-- . -- . --
2. The main menu will appear on the TV screen.
---
3. Press W or w to select the SYSTEM and press
ENTER/OK.
1 2
TIME
DATE
i
2. Use the numbered buttons on the remote control
to alter the HOURS, MINUTES, DAY, MONTH and
YEAR.
Please note your DVD+VCR uses a 24 hour
clock. e.g. 1pm will be displayed as 13:00.
The day of the week will appear automatically
when you enter the year.
4. Press v or V to select according to the
COLOUR system used.
5. Press w to select the RF Out sound system compatible to your TV.
1 2
REC
f OSD
ON
OFF
HH MM
8 : 00
DD MM
YY
1 . 01 . 04
+
16:9
4:3
-
DECODER
OPR
VCR
SYSTEM
NIC
Dr.
SYSTEM
i
THU
6. Press VCR MENU to remove the menus from the
TV screen.
1 2
TIME
DATE
RF IPr-12/ I TIME
RF ACMS
B/G DATE
RF D/K
PSET
R
i
3. If you make a mistake press W or w and enter the
correct details.
4. Press VCR MENU to return to a TV picture.
1-21
Tuning in TV Stations Automatically
This DVD+VCR can easily be programmed by
using the menus displayed on screen.
The menus are controlled from the Remote
Control Handset.
If the TV broadcast signal is weak your
DVD+VCR may not detect the necessary information and will not be able to store them correctly. To overcome this problem please turn to
the MANUAL TUNING section on page 18.
1. Switch on your TV set and video recorder by
pressing the I/ button.
1. Press I/
2. Press VCR MENU button.
The main menu will appear on the TV screen.
1 2
Pr-12
REC
PSET
R
ACMS
f OSD
ON
OFF
16:9
4:3
DECODER
+
TIME
DATE
2. Press VCR MENU button.
The main menu will appear on the TV screen.
Press v or V to select the ACMS.
Press ENTER/OK.
3. Press v or V to select COUNTRY.
(A:Austria, B:Belgium, CH:Switzerland,
D:Germany, DK:Denmark, E:Spain, F:France,
I:Italy, N:Norway, NL:Nertherlands, P:Portugal,
S:Sweden, SF:Finland, Others)
Press ENTER/OK to start the automatic tuning
process.
VCR
SYSTEM
Dr.
NIC
-
OPR
to turn on your DVD+VCR.
REC
OK i
• REC - Timer recording setting (see p. 27).
• PR SET - Manual tuning setting (see p. 18).
• ACMS - ACMS (Automatic Channel Memory
System) (see p. 17).
• TIME DATE - Date & clock setting (see p. 16).
• SYSTEM - To set the Colour TV System
•
•
•
•
•
•
A
N
(see p. 16).
Dr. - To check a problem with your VCR
(see p. 42).
F.OSD ON/OFF - To display the operational
mode of your VCR (see
p. 41).
16:9/4:3 - To select the aspect ratio of your TV
(see p. 42).
DECODER - To use a pay-TV decoder (or
Satellite) with your VCR (see
p. 43).
OPR - To improve the playback picture
(see p. 25).
NIC - To activate or deactivate the NICAM digital sound (see p. 41).
3. Press W or w to select the desired menu.
Press ENTER/OK and use v or V to select.
B CH
NL
P
D DK E F I
S SF OTHERS
Pr-12
OK i
ACMS
4. The TV STATION TABLE will appear when tuning
is completed.
Press VCR MENU to save your settings.
01
02
03
04
05
06
07
08
P
RSET
C02
C03
C04
C05
C06
C07
C08
C09
00
00
00
00
00
00
00
00
MOVE :
DELETE :
ARD
ZDF
WDR 3
BR3
HR3
N3
NDR 3
SWF3
,
OK i
Notes:
• The DVD+VCR’s clock will be set automatically
when automatic tuning has finished. If the clock is
wrong please see “Setting the clock Manually” on
page 16.
• Please note currently only a limited number of TV
companies transmit the Programme Delivery
Control (PDC) signal which enables your
DVD+VCR to successfully identify and store them.
If your DVD+VCR has difficulty in identifying a TV
station please turn the page to find out how to
manually tune in and name a TV station. While
automatic tuning is taking place the time and date
will set automatically.
If - - :- - appears in the DVD+VCR display it means
that the broadcast signal is weak and the clock was
not set. Please turn to CLOCK SET section of this
book on page 16.
4. Press VCR MENU to return to a TV picture.
1-22
Preparation
How to use the main menu
Tuning in TV Stations Manually
In certain areas of the country broadcast signals
may be too weak for your DVD+VCR’s automatic tuning process to find or assign TV stations
correctly. You must tune in these weaker broadcast stations manually in order for your
DVD+VCR to store them.
1. Press VCR MENU.
The main menu will appear on the TV screen.
Press W or w to select the PR SET.
Press ENTER/OK.
PR
01
1 2
Pr-12
REC
PSET
R
ACMS
f OSD
ON
OFF
16:9
4:3
DECODER
+
TIME
DATE
MFT
00
PR
09
CH
C10
ARD
ZDF
WDR 3
BR3
HR3
N3
NDR3
SWF3
MFT
00
OK i
P
RSET
6. Use D or E to select a station name from the list.
Press ENTER/OK to select it.
If your station name isn’t on the list do not press
ENTER/OK, but go to stage 7.
STATION
PR-01
VCR
SYSTEM
Dr.
CHANNEL/CABLE : AV
PSET
R
NIC
-
CH
C 02
5. Press w to select STATION so that you may
name your TV station.
Press ENTER/OK.
The TV station name list will appear.
PR
09
2. Press VCR MENU.
The station table will appear.
Press v or V to select the programme number
that you want to tune (for example, PR 09).
01
02
03
04
05
06
07
08
C02
C03
C04
C05
C06
C07
C08
C09
00
00
00
00
00
00
00
00
,
CH
C--
MFT
--
OK i
i
Press G.
Use v or V to select letters and numbers for
the new station name.
Use W or w to move back and forth between
characters.
Press ENTER/OK.
PR
C09
10
11
12
13
14
15
16
PSET
R
CH
C10
MFT
00
STATION
----
CHANNEL/CABLE : AV
P
RSET
CH
C10
MFT
00
STATION
ZDF
OK i
PSET
R
09
4. Searching will stop when it locates a stations.
Press to select MFT.
Control the fine tuning of the station by using v
or V.
PR
09
OK i
8. Press VCR MENU, confirm the station placement.
Press VCR MENU again.
Your new TV station has now been tuned into your
DVD+VCR.
If you wish to manually tune other stations repeat
stages 1 - 8.
STATION
----
CHANNEL/CABLE : AV
PSET
R
MFT
00
7. You can change a TV station name manually
rather than using the “standard” names.
3. Press ENTER/OK.
Press INPUT SELECT to select C (Standard
stations) or S (Cable stations):
C02 - C69, S01 - S41.
Enter the channel number of station that you want
to tune with the numbered buttons or use v or
V to find the required station.
PR
09
CH
C10
PSET
R
PR-01
PR-02
PR-03
PR-04
PR-05
PR-06
PR-07
PR-08
MOVE :
DELETE :
PSET
R
ARD
ZDF
WDR 3
BR3
HR3
N3
NDR3
SWF3
i
PSET
R
OK i
OPR
i
1-23
C10
--------
00
-------MOVE :
DELETE :
-
ZDF
---------------------,
OK i
Deleting TV Stations
After tuning TV stations into your DVD+VCR you
may wish to change the order in which they are
stored without having to retune them again. The
instructions given on this page will show you how
you can simply move them into your desired
order.
After tuning TV stations into your VCR you may
wish to delete a station.
The instructions given on this page will show you
how you can easily delete any unwanted TV
stations.
1. Press VCR MENU.
The main menu will appear on the TV screen.
Use W or w to select the PR SET.
Press ENTER/OK.
1. Press VCR MENU.
The main menu will appear on the TV screen.
Press W or w to select the PR SET.
Press ENTER/OK.
PR
01
PR
01
1 2
REC
P
RSET
f OSD
ON
OFF
Pr-12
ACMS
+
16:9
4:3
TIME
DATE
DECODER
MFT
00
STATION
PR-01
1 2
VCR
SYSTEM
Dr.
P
RSET
NIC
-
CH
C 02
P
RSET
ACMS
16:9
4:3
DECODER
+
TIME
DATE
STATION
PR-01
VCR
SYSTEM
Dr.
P
RSET
NIC
-
MFT
00
CHANNEL/CABLE : AV
OK i
OPR
PSET
R
i
CHANNEL/CABLE : AV
OK i
OPR
Pr-12
REC
f OSD
ON
OFF
CH
C 02
PSET
R
i
2. Press VCR MENU.
2. Press VCR MENU.
Press v or V to select the programme number
you want to move (for example, PR-03).
Press w.
01
02
03
04
05
06
07
08
PSET
R
C02
C03
C04
C05
C06
C07
C08
C09
00
00
00
00
00
00
00
00
PR-01
PR-02
PR-03
PR-04
PR-05
PR-06
PR-07
PR-08
MOVE :
DELETE :
,
01
02
03
04
05
06
07
08
OK i
C02
C03
C05
C06
C04
C07
C08
C09
00
00
00
00
00
00
00
00
PR-01
PR-02
PR-04
PR-05
PR-03
PR-06
PR-07
PR-08
C02
C03
C05
C06
C04
C07
C08
C09
PR-01
PR-02
PR-04
PR-05
PR-03
PR-06
PR-07
PR-08
P
RSET
4. Press ENTER/OK.
The selected programme will be moved to the
new programme number.
If you wish to move other TV stations repeat stages
1 - 4.
Press VCR MENU to remove the menus from the
TV screen.
P
RSET
C02
C03
C05
C06
C04
C07
C08
C09
00
00
00
00
00
00
00
00
MOVE :
DELETE :
00
00
00
00
00
00
00
00
PR-01
PR-02
PR-03
PR-04
PR-05
PR-06
PR-07
PR-08
MOVE :
DELETE :
,
OK i
4. Press .
After a short while, the selected station will be
deleted.
If you wish to delete other TV stations repeat
stages 3 - 4.
01
02
03
04
05
06
07
08
OK i
P
RSET
01
02
03
04
05
06
07
08
C02
C03
C04
C05
C06
C07
C08
C09
OK i
PSET
R
00
00
00
00
00
00
00
00
01
02
03
04
05
06
07
08
PSET
R
3. Press v or V to select the programme number
you want to move to (for example, PR-05).
01
02
03
04
05
06
07
08
3. Press v or V to select the programme number
you want to delete. (for example, PR-01)
PR-01
PR-02
PR-03
PR-04
PR-05
PR-06
PR-07
PR-08
,
C03
C04
C05
C06
C07
C08
C09
--
00
00
00
00
00
00
00
-MOVE :
DELETE :
PR-01
PR-02
PR-03
PR-04
PR-05
PR-06
PR-07
----,
OK i
5. Press VCR MENU to remove the menus from the
TV screen.
How to select Stored TV stations:
Stored TV stations can be selected in either of two
ways.
Use PR/TRK + or - to select different stations that
are tuned into your DVD+VCR.
OK i
You may also directly select stations using the
numbered buttons on the remote control.
1-24
Preparation
Changing the order of TV Stations
Example: On-Screen Display during
playing DVD Video
DVD On-Screen Display
You can display the general playback status on the
TV screen. Some items can be changed using the
menu. To use the on-screen display:
Items
Selection Method
Title Number
1/3
W / w, Numbers
ENTER/OK
1 / 12
W / w, Numbers
ENTER/OK
1. Press DISPLAY during playback.
Chapter Number
2. Press v /V to select an item.
The selected item is highlighted.
Time search
3. Press W / w to change the setting. You can also
use the number buttons if appropriate (e.g.
inputting the title number). For some functions,
press ENTER/OK to execute the setting.
0:20:09
Audio language
and Digital Audio
Output mode
Subtitle language
Notes:
• Some discs may not provide all of the features
shown below.
CH
ABC
1 ENG
Angle
1/3
Numbers, ENTER/OK
W / w or
AUDIO
W / w or
SUBTITLE
W / w or
ANGLE
W/ w
• If no button is pressed for 10 seconds, the onscreen display disappears.
Sound
Playback Status/Restrictions
Title
Repeat title
Example: On-Screen Display during
playing VCD
Repeat sequence
A-B
1/9
Items
Enter a Marker
MARKER SEARCH
1 2 3 4 5 6 7 8 9
3D SUR
Selection Method
Track Number
(or PBC mode)
Marker Search menu
1/3
Time search
Resume play from this point
Action prohibited or not available
0:20:09
Sound
Track Number
1/3
Time search
0:20:09
Audio language
and Digital Audio
Output mode
Subtitle language
Sound
1
MP3
3D SUR
W / w Numbers ENTER/OK
Numbers, ENTER/OK
Items
Selection Method
Group Number
1/2
W / w , Numbers
ENTER/OK
Track Number
1/6
W / w , Numbers
ENTER/OK
Time search
W / w or
0:20:09
AUDIO
ABC
ENG
3D SUR
W/ w
Example: On-Screen Display during
playing DVD Audio
Selection Method
Items
Numbers
ENTER/OK
W / w or
AUDIO
Audio Channel
Example: On-Screen Display during
playing divx movie disc
W / w, Numbers
ENTER/OK
W / w or
AUDIO
DVD Audio
Output mode
W / w or
Display only
SUBTITLE
Subtitle language
W/w
OFF
ABC
Page (or Angle)
1 / 21
or
Display only
W / w or
ANGLE
1/3
Sound
1-25
3D SUR
W / w
Initial Settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound. You
can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 21 to 24.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
Other: To select another language, press number buttons then ENTER/OK to enter the corresponding 4-digit
number according to the language code list in the reference chapter (see p. 44). If you enter the wrong language code, press CLEAR.
DISPLAY
DISPLAY
To go to the next level:
Press w on the remote control.
4 : 3
TV Aspect
To go back to the previous level:
Press W on the remote control.
Display Mode
Panscan
Progressive Scan
Off
TV Output Select
RGB
General Operation
Move
1. Press SETUP.
The Setup menu appears.
2. Use v / V to select the desired option then press
w to move to the second level. The screen shows
the current setting for the selected item, as well
as alternate setting(s).
3. Use v / V to select the second desired option
then press w to move to the third level.
TV Aspect
DVD-V
5. Press SETUP or PLAY to exit the Setup menu.
DVD-A
4:3 : Select when a standard 4:3 TV is connected.
16:9 Wide: Select when a 16:9 wide TV is
connected.
Display Mode
4. Use v / V to select the desired setting then press
ENTER/OK to confirm your selection. Some items
require additional steps.
Select
DVD-V
DVD-A
Display Mode setting works only when the TV Aspect
mode is set to “4:3”.
Letterbox: Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan: Automatically displays the wide picture on the
entire screen and cuts off the portions that do not fit.
LANGUAGE
Progressive Scan
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
LANGUAGE
Menu Language
English
Disc Audio
Original
Disc Subtitle
Off
Disc Menu
Original
Move
Select
Menu Language
Select a language for the Setup menu and on-screen
display.
Disc Audio / Subtitle / Menu
DVD-V
DVD-A
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
1-26
Preparation
Original: Refers to the original language in which the
disc was recorded.
To turn on progressive scan:
Dolby Digital / DTS / MPEG
Connect component out of this unit to the input of
your monitor/television, set your television or monitor
to component Input.
1. Select “Progressive Scan” on the DISPLAY menu
then press w.
TV Aspect
Display Mode
Progressive Scan
On
Off
DVD-A
DivX
Bitstream: Select “Bitstream” if you connect the
DVD+VCR’s DIGITAL AUDIO OUT jack to an
amplifier or other equipment with a Dolby Digital,
DTS or MPEG decoder.
PCM (for Dolby Digital / MPEG): Select when
connected to a two-channel digital stereo amplifier. DVDs encoded in Dolby Digital or MPEG will
be automatically downmixed to two-channel PCM
audio.
DISPLAY
TV Output Select
DVD-V
Off (for DTS): If you select “Off”, the DTS signal
is not output through the DIGITAL OUT jack.
Prev.
Move
Sample Freq. (Frequency)
Enter
DVD-V
DVD-A
If your receiver or amplifier is NOT capable of handling 96 kHz signals, select 48 kHz. When this choice
is made, this unit automatically converts any 96 kHz
signals to 48 kHz so your system can decode them.
2. Select “On” using the v /V buttons.
3. Press ENTER/OK to confirm your selection.
The confirm menu will appear.
4. When the confirm menu appears on your screen
“Cancel” is highlighted as default. Use the W button to highlight “Enter”.
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz. When this choice is
made, this unit passes each type of signal through
without any further processing.
5. Pressing ENTER/OK will set this unit to progressive scan mode.
Check the documentation for your amplifier to verify
its capabilities.
TV Output Select
Set this unit’s TV Output Select options according to
the TV connection type.
YPbPr: When your TV is connected with the
COMPONENT/PROGRESSIVE SCAN VIDEO OUT
jacks on this unit.
RGB: When your TV is connected with the SCART
(RGB signal) jack.
Dynamic Range Control (DRC)
DVD-V
DVD-A
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic presentation possible, thanks to digital audio technology.
However, you may wish to compress the dynamic
range of the audio output (the difference between the
loudest sounds and the quietest ones). This allows
you to listen to a movie at a lower volume without losing clarity of sound. Set DRC to On for this effect.
Vocal
DVD-V
Set to On only when a multi-channel karaoke DVD is
playing. The karaoke channels on the disc mix into
normal stereo sound.
AUDIO
Each DVD disc has a variety of audio output options.
Set this unit’s AUDIO options according to the type of
audio system you use.
AUDIO
Dolby Digital
Bitstream
DTS
Bitstream
MPEG
PCM
Sample Freq.
48KHz
DRC
On
Vocal
On
Move
Select
1-27
OTHERS
Note:
On
Auto Play
Off
B.L.E.
On
Pluge
On
DNR
Off
• While the DNR2 (expanded level) can provide additional
DivX(R) VOD
Select
• Depending on the disc, some picture detail may be lost by
the picture enhancement.
Move
PBC
quality of the disc.
improvement in the reduction of noise in the video signal,
it may produce undesirable picture artifacts on some
discs. Should this occur, select a more appropriate DNR
level (normal or off).
OTHERS
PBC
• Actual picture enhancement may vary depending on the
• A DVD audio disc with Dolby Digital or DTS soundtrack
may be played, some DVD audio discs include moving
pictures which may be modified by the above processes.
Select
VCD
DivX(R) VOD
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to the PBC.
DivX
You can show the DivX DRM (Digital Right
Management) Registration code for your unit only.
Off: Video CDs with PBC are played the same way as
Audio CDs.
DivX(R) Video On Demand
Your registration code is : XXXXXXXX
Auto Play
DVD-V
You can set up the DVD+VCR so a DVD disc automatically starts playing whenever the DVD is inserted.
If Auto Play mode is set to On, this DVD+VCR will
search for title that has the longest playback time and
then play back the title automatically.
On: Auto Play function is active.
To learn more visit
www.divx.com/vod
(Done)
The Registration code is used for VOD (Video-OnDemand) service agent. You can purchase or rental
an encrypt movie file.
Off: Auto Play function is not active.
Notes:
Note:
If you rent the DivX VOD file, it has several options of
viewing limits as show below.
The Auto Play function may not work for some DVDs.
• Display the number which you can watch the file.
B.L.E. (Black Level Expansion)
To select the black level of playback pictures. Set your
preference and monitor’s ability.
On: Expanded grey scale. (0 IRE cut off)
View DivX(R) VOD Rental
This rental has 3 view left.
Do you want to use one
of you 3 views now?
Off: Standard grey scale. (7.5 IRE cut off)
(Yes) (No)
Note:
The B.L.E. function works on NTSC system only.
• The rental has been expired.
Pluge (Blacker than Black)
DVD-V
For proper adjustment of your television brightness
settings utilizing a commercially available test disc.
Rental Expired
On: Select when you adjust the level of your TV using a commercially available test disc that contains pluge signals.
(Done)
Off: For normal use.
DNR (Digital Noise Reduction)
DVD-V
VCD2.0 VCD1.1
• Display the authorization error.
You can reduce ambient noise in the picture.
Authorization Error
DNR1: Normal level
This player is not authorized
to play this video.
DNR2: Expanded level.
Off:
Off.
(Done)
1-28
Preparation
The PBC, Auto Play, B.L.E., Pluge, DNR and DivX(R)
VOD settings can be changed.
LOCK (Parental Control)
4. Press ENTER/OK to confirm your rating selection,
then press SETUP to exit the menu.
5. Press OPEN/CLOSE (U) to activate parental
control.
LOCK
Rating
Unlock
Password
New
Country Code
DE
Password (Security Code)
You can enter or change password.
Move
Rating
Select
1. Select “Password” on the LOCK menu then press
w.
DVD-V
Some movies contain scenes that may not be suitable for children to view. Many of these discs contain
parental control information that applies to the complete disc or to certain scenes on the disc. Movies
and scenes are rated from 1 to 8, depending on the
country. DVD video discs may or may not respond to
the parental control setting if the Country code of the
disc is set wrongly. Some discs offer more suitable
scenes as an alternative.
The parental control feature allows you to block
access to scenes below the rating you input, thereby
preventing your children from being able to view
material you believe is unsuitable.
1. Select “Rating” on the LOCK menu then
press w.
2. Press ENTER/OK.
3. Follow step 2 as shown left (Rating). “Change” or
“New” is highlighted.
4. Enter the new 4-digit code, then press ENTER/OK.
Input it again to verify.
5. Press SETUP to exit the menu.
If you forget your Security Code
If you forget your security code you can clear it using
the following steps:
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number “210499” and the security
code is cleared.
2. To access the Rating, Password and Country
Code features, you must input the 4-digit security
code you created. If you have not yet entered a
security code you are prompted to do so.
3. Enter a new code as described above.
Country Code
Input a 4-digit code and press ENTER/OK. Enter it
again and press ENTER/OK to verify. If you make
a mistake before pressing ENTER/OK, press
CLEAR.
3. Select a rating from 1 to 8 using the v / V buttons.
DVD-V
Enter the code of the country/area whose standards
were used to rate the DVD video disc, based on the
list in the reference chapter (see p. 44).
1. Select “Country Code” on the LOCK menu then
press w.
2. Follow step 2 as shown left (Rating).
Rating 1-8: Rating one (1) has the most restrictions and rating eight (8) is the least restrictive.
3. Select the first character using v /V buttons.
Unlock
If you select unlock, parental control is not active
and the disc plays in full.
Note:
If you set a rating for the player, all disc scenes with the
same rating or lower are played. Higher rated scenes
are not played unless an alternate scene is available on
the disc. The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback
stops. You must enter the 4-digit password or change the
rating level in order to play the disc.
1-29
4. Press ENTER/OK and select the second character using v /V buttons.
5. Press ENTER/OK to confirm your country code
selection.
Operation
Playing a tape
You will only be able to load and eject video cassettes
when your DVD+VCR is plugged into the mains.
Your DVD+VCR may also playback recordings from
NTSC tapes (on PAL TV).
Getting a better picture
When a cassette is inserted and playback started, the
automatic tracking function works to get the best possible picture automatically. If the quality of the recording is
poor, repeatedly press v or V on the remote control to
manually adjust the tracking until any distortions have
been removed.
1. Make sure that you have correctly connected your
DVD+VCR as described earlier in this book.
Turn on your TV.
Press I/ to turn on your DVD+VCR.
Insert the video cassette into your DVD+VCR.
The video cassette should have the window side facing
up and the arrow facing away from you.
During playing back or still picture press W or w.
You can reach the following playback speeds.
(-7xplay, -3xplay, -play, still, 1/19 slow, play, 2xplay,
7xplay)
To switch off the slow motion and shuttle, press the
desired function. During slow motion and shuttle, the
noise bars may appear on the picture according to the
status of tape. If distortions can be seen in the picture,
reduce them with v or V.
6. Press STOP ■ to end playback.
Press EJECT U.
If the end of the tape is reached, your DVD+VCR will
stop playback automatically, rewind, stop, eject the tape
and go to standby.
CM (Commercial Message) Skip:
This feature enables you to skip a commercial break
in a few seconds during tape playback, then resume
normal playback.
While tape is playing press INSTANT SKIP on the
remote control to skip commercial (or another
programme material).
2. Press PLAY w to start playing your tape.
If you load a video cassette which has had its
record protection tab removed, playback of the
cassette will start automatically.
Repeatedly press INSTANT SKIP to skip:
1 Press
30 seconds
AUTO TRACKING
Your DVD+VCR will automatically adjust the
tracking to give the best picture quality.
If noise bars appear during playback, adjust the tracking
manually by pressing PR/TRK+/-.
To resume automatic tracking, press AUTO TRK.
3. Press PAUSE/STILL II/R to still a picture.
Press PAUSE/STILL II/R repeatedly to advance
the tape frame by frame.
If you press SLOW R, the picture will be slowed down at
about 1/19 times the normal playback.
Tapes can be paused for up to 5 minutes. After 5 minutes
your DVD+VCR will stop the tape to prevent damaging
the tape or your DVD+VCR. Still picture quality can be
improved slightly by using v or V.
4. Press PLAY w to continue playing your tape.
Picture search:
During playing back press either REW b or FWD f
to this will enable you to rapidly wind the tape (7 times
normal playback) and see where you are on the tape.
Logic search:
During fast forwarding or rewinding press and hold FWD
or REW respectively. The picture will be played back
at 7 times normal playback speed.
2 Press
60 seconds
3 Press
90 seconds
4 Press
120 seconds
5 Press
150 seconds
6 Press
180 seconds
OPR (Optimum Picture Response)
This feature automatically improves playback picture
quality by adjusting your DVD+VCR to the condition
of the tape.
1. Press VCR MENU.
2. Press W or w to select OPR.
3. Press ENTER/OK.
4. Press v or V repeatedly to select: OFF, SOFT or
SHARP.
Please note that you can only set OPR when
playing a tape.
1 2
OFF
PSET
RECSOFT
R
Pr-12
ACMS
f OSDSHARP
ON
16:9 DECODER
OFF
4:3
+
TIME
DATE
VCR
SYSTEM
NIC
-
OPR
Dr.
OPR
i
5. Press VCR MENU return to screen.
1-30
Preparation
5. Slow motion playback, Shuttle :
One-touch Timer Recording (OTR)
Your DVD+VCR allows you to make recordings
using a variety of simple methods:
One-touch Timer Recording (OTR) start
recording immediately for a set period of time or
until the video cassette runs out.
Your DVD+VCR incorporates Long Play (LP)
which enables you to record up to twice the
amount of time on a video cassette. For example
an E-180 will record up to 180 minutes using
Standard Play (SP); using LP you will be able to
record up to 360 minutes. Please note there will be
a slight loss in picture and sound quality when
using LP.
7. Press PAUSE/STILL II/R to avoid recording
unwanted scenes.
Press PAUSE/STILL II/R to continue recording.
Tapes can be paused for up to 5 minutes; RECP
will be displayed briefly when a tape is paused.
After 5 minutes your DVD+VCR will stop recording
to prevent damaging the tape or your DVD+VCR.
8. Press STOP ■ to end recording.
Press EJECT U.
EJECT will appear on the TV screen for a few
seconds.
Notes:
• If you do not wish to record on a tape (this can
happen quite easily by accident!) remove the protection tab on the back edge of the video cassette.
1. Make sure that you have correctly connected your
DVD+VCR as described earlier in this book.
Press I/ 1 to turn on your DVD+VCR.
• It is possible to record on a video cassette with the
2. Insert a video cassette with protection tab into
your DVD+VCR.
The video cassette should have the window side
facing up and the arrow facing away from you.
• Remember you can record one programme while
record protection tab removed by covering the hole
with self adhesive tape.
watching another by starting your instant recording,
press TV/VCR to select TV mode and then selecting a different channel on your TV.
3. Press PR/TRK + or - to select the programme
number you wish to record.
You may also directly select programme number
using the numbered buttons on the remote control.
4. If you wish to record directly from the SCART
sockets or AV jacks, press INPUT SELECT
repeatedly until the input you wish to record from
is displayed.
AV 1 for recording from EURO AV1 SCART socket
on the rear of your unit.
AV 2 for recording from EURO AV2 SCART socket
on the rear of your unit.
AV 3 for recording from VIDEO IN and AUDIO IN
(Left & Right) jacks on the front of your unit.
5. Press SP/LP if you wish to record in Long Play or
Standard Play.
SP will produce improved picture and sound quality, however LP will provide twice as much recording time as SP.
6. Press REC/OTR on the remote to start recording.
RECORD will appear on the TV screen.
Press REC on your unit or press REC/OTR on the
remote several times. Each successive press will
increase the record time by 30 minutes until you
reach a maximum of 9 hours.
1-31
Timer recording using On
Screen Display
If you press ENTER/OK before entering the date
you may select one of the following automated
recording features. Press W or w to select, then
press ENTER/OK to confirm.
You may set up to seven timer record events
within one month of the current date.
Note:
Before setting the timer make sure that you have set the
DVD+VCR clock correctly and you know which stations you
have tuned TV stations on your DVD+VCR.
2. Press VCR MENU.
Press W or w to select REC.
Press ENTER/OK.
3. Press ENTER/OK to start setting the timer record
event.
If all timer record events are full press v or V to
select the event that you wish to remove and
replace.
Press W to delete the event.
-
TIME
- : - - ~ - -: - : - - ~ - -: - : - -~- - : - : - -~- - : - : - -~- - : - : - -~- - : - : - -~- - : -
-
SU~SA To record at the same time every week.
PR
DATE
T I M E
- - : - - ~ - -: - PR-01
16
--- - : - - ~ - -: - --- - : - -~- - : - --- - : - -~- - : - --- - : - -~- - : - --- - : - -~- - : - --- - : - -~- - : - DLY SU MO TU WE TH FR
1. Insert a video cassette with protection tab into
your DVD+VCR.
The video cassette should have the window side
facing up and the arrow facing away from you.
PR
DATE
-PR-01
-------------
DLY To record every day (except Saturday and
Sunday) at the same time.
6. Press the numbered buttons to enter the recording start and end times of the programme that you
wish to record.
Please note your DVD+VCR uses a 24 hour
clock. e.g. 1pm will be displayed as 13:00.
You may also select the start and end times by
using v or V.
PR
PR-01
-------
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SA
OK i
DATE
T I M E
16
19 : 00 ~ 20: 00
-- - : - - ~ - -: - -- - : - -~- - : - -- - : - -~- - : - -- - : - -~- - : - -- - : - -~- - : - -- - : - -~- - : - -
SP
SP
SP
SP
SP
SP
SP
i
i
4. Press the numbered buttons to enter the station
that you wish to record.
When selecting stations 1 - 9, press 0 first, then
the channel number; for example Stations 3 - 03.
You may also select Channels by pressing v or
V. Once selected press W.
If you wish to record from AUDIO IN (L/R) and
VIDEO IN on the front or from the EURO SCART
sockets on the back of your unit, press INPUT
SELECT to select for correct display (AV1, AV2
or AV3).
PR
PR-01
-------
DATE
--------
-
TIME
- : - - ~ - -: - : - - ~ - -: - : - -~- - : - : - -~- - : - : - -~- - : - : - -~- - : - : - -~- - : -
-
SP
SP
SP
SP
SP
SP
SP
7. Press w and press v or V to switch VPS/PDC
on or off.
Press w to select the recording speed.
Press v or V to select the desired tape speed
(SP, IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program. IP mode is not
selected when VPS/PDC is ON.
PR
PR-01
-------
DATE
T I M E
16
19 : 00 ~ 20: 00
- - : - - ~ - -: - --- - : - -~- - : - - - : - -~- - : - --- - : - -~- - : - - - : - -~- - : - -- - : - -~- - : - --
SP
SP
SP
SP
SP
SP
SP
i
i
1-32
Operation
5. Press the numbered buttons to enter the date of
the programme.
8. Press VCR MENU to set another timer record
event and follow steps 3 to 7.
Check that the timer event details are correct.
Press VCR MENU twice.
• Video Programme System (VPS)
The Video Programme System (VPS) ensures that
the TV programmes that you have programmed for
timer recording will be recorded exactly from their
beginning to end, even if the actual broadcasting
time differs from the scheduled time due to delayed
start, or if the programme is extended beyond its
scheduled time. Also, if a programme is interrupted,
for example, if a news flash is inserted, the recording will also be interrupted automatically and
resumed when the programme continues.
The VPS signal is broadcast by the TV station and
this controls the timer in the video recorder.
VPS should be set ON for all timer recordings from
TV stations broadcasting these signals. It should be
set OFF for all timer recordings from TV stations
that are not broadcasting these signals.
If PLEASE CHECK is displayed, you have
entered incorrectly and will need to re-enter the
data.
Press I/ to switch your DVD+VCR to Timer
Standby mode.
The timer symbol ( ) will appear in the display
window while your DVD+VCR waits to make the
recording.
9. Press STOP (■) to end timer recording.
Notes:
• During timer recording standby mode, the DVD and
*** The similar system PDC, which is used in the
time being in the Netherlands, can also be used
with your new video recorder.
VCR mode cannot be operated. To use the
DVD+VCR, press I/
. After you use the DVD or
VCR, press I/
again to put the VCR into timer
recording standby mode.
• If at a later date you wish to delete or change any
of the settings in timer event memory you may do
so without having to enter all the timer event information again. Simply display the timer event
screen. Use v or V to select the event that you
wish to delete or change.
Press W to delete the event...or
Press ENTER/OK to change; then press W or w to
select; Station, Date, Start and End times and LP.
Press v or V to enter the correct information.
• If Timer record events Overlap...
Make sure that the preset times of the timer recording events do not overlap. If they do, the earlier programme will always be given priority.
Example:
Programme 1 is programmed to start at 16:00 and
end at 17:00.
Programme 2 is programmed to start at 16:30 and
end at 17:30.
(In this case, Programme 1 will be recorded in its
entirety, but only the last 30 minutes of Programme
2 will be recorded.)
• To watch a DVD while performing a timer recording,
press TV/VCR to select VCR mode. Then press
DVD to view the DVD deck output source on the TV
screen.
1-33
SHOWVIEW greatly simplifies entering the date,
channel, start and end times of a Timer
Recording by simply entering a SHOWVIEW
Code. SHOWVIEW Codes are published in most
TV guide magazines; they can vary one to nine
numbers in length.
SHOWVIEW is a registered trademark of Gemstar
Development Corporation.
The SHOWVIEW system is manufactured under
licence from Gemstar Development Corporation.
1. Make sure that TV channels have been tuned and
stored in correct SHOWVIEW order.
Insert a video cassette with protection tab into
your DVD+VCR.
2. Press SHOWVIEW.
ONCE
0~9,
3. Press
D
or
E
OK i
DATE
12
-------
TIME
10 : 11 ~ 11 : 55
- - : - - ~ - -: - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - -
SP
SP
SP
SP
SP
SP
SP
i
6. Press F or G to select the settings that you wish to
revise. (PR, DATE, TIME, VPS/PDC and SP).
Press D or E to enter the correct information.
PR
ARD
-------
DATE
12
-------
TIME
10 : 11 ~ 11 : 55
- - : - - ~ - -: - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - -
SP
SP
SP
SP
SP
SP
SP
i
7. Press G and press D or E to switch VPS/PDC on
or off. Press G to select the recording speed.
Press D or E to select the desired tape speed (SP,
IP, or LP).
PR
ARD
-------
SHOWVIEW NO.
---------
REC
PR
ARD
-------
DATE
12
-------
TIME
10 : 11 ~ 11 : 55
- - : - - ~ - -: - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - -
SP
SP
SP
SP
SP
SP
SP
i
to select the recording type.
ONCE: To record once.
DAILY: To record every day (except Saturday and
Sunday) at the same time.
WEEKLY: To record at the same time every week.
4. Press the numbered buttons to enter the
SHOWVIEW Code of the TV programme that you
wish to record.
If you make a mistake press F then enter the
revised number.
Notes:
• IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program.
• IP mode is not selected when VPS/PDC is ON.
Check that the timer event details are correct.
• If you wish to record from AUDIO IN and VIDEO IN
on the front or from either of the EURO SCART
sockets on the back of DVD+VCR, press INPUT
SELECT to select for correct display (AV1, AV2 or
AV3).
• If you want to make another SHOWVIEW recording
repeat stages 3 - 7 by pressing SHOWVIEW twice.
8. Press VCR MENU twice to return to TV Picture.
246876543
ONCE
REC
0~9,
OK i
5. Press ENTER/OK.
If PLEASE CHECK is displayed it means that you
have entered the wrong SHOWVIEW number,
entered the SHOWVIEW number correctly.
If “- -” is displayed, you have to enter the programme number of the station, you want to record
from.
1-34
If PLEASE CHECK is displayed, you have entered
incorrect information and will need to re-enter the
data.
Press I/ to switch your DVD+VCR power off
mode.
will appear in the video recorder’s display while your DVD+VCR waits to make the
recording. To watch a DVD+VCR during timer
recording standby mode, press + / 1 and switch
DVD+VCR to DVD mode.
Operation
SHOWVIEW Programming
Playing a DVD or Video CD
General Features
Playback Setup
Notes:
Unless stated otherwise, all operations described use
the remote control. Some features may also be available on the Setup menu.
1. Turn on the TV and select the video input source
connected to the DVD+VCR.
2. Turn on the audio system (if applicable) and
select the input source connected to the
DVD+VCR.
Moving to another TITLE/GROUP
DVD-V
DVD-A
When a disc has more than one title/group, you can
move to another title/group. Press DISPLAY, then the
appropriate number (0-9) or use b / B to move
to another title/group.
3. Press OPEN/CLOSE (U) to open the disc tray
and load your chosen disc in the tray, with the
playback side down.
4. Press OPEN/CLOSE (U) to close the tray.
Playback starts automatically. If playback does not
start, press PLAY (G).
In some cases, the disc menu might appear
instead.
5. To stop the playback, press STOP ■.
The unit records the stopped point, depending on the
disc. “II■” appears on the screen briefly. Press PLAY to resume playback (from the scene point). If you press
STOP ■ again or unload the disc (“■” appears on the
screen.), the unit will clear the stopped point.
Press OPEN/CLOSE U to remove the disc.
Press OPEN/CLOSE U to close disc tray or press I/
, the disc tray closes automatically and unit turns off.
If a menu screen is displayed
The menu screen may be displayed first after loading
a DVD or Video CD which offer a menu.
DVD-V
Use the F G v V buttons to select the
title/chapter you want to view, then press
ENTER/OK to start. Press TOP MENU or MENU
to return to the menu screen.
Moving to another CHAPTER/TRACK
DVD-V
DVD-A
VCD
DivX
When a title on a disc has more than one chapter or
a disc has more than one track, you can move to
another chapter/track as follows:
•
Press SKIP F or B briefly during playback
to select the next chapter/track or to return to the
beginning of the current chapter/track.
•
Press SKIP B twice in quick successions to
step back to the previous chapter/track.
•
To go directly to any chapter during DVD playback, press DISPLAY and press v / V to select
the chapter/track icon. Then, input the
chapter/track number or use F / G.
Search
DVD-V
DVD-A
VCD
DivX
1. Press REW b or FWD f during playback.
2. Press REW b or FWD f repeatedly to select
the required speed.
DVD, DivX disc; X2, X4, X16 or X100
Video CD; X2, X4 or X8
DVD-A
Use the F G v V buttons to select an option
you want, then press ENTER/OK to view the
option.
3. To exit SEARCH mode, press PLAY (G).
VCD
Use the number buttons to select the track you
want to view and press RETURN to return to the
menu screen. Menu settings and operating procedures may differ. Follow the instructions on each
menu screen. You also may set PBC to Off (See
“PBC” on page 23).
Note:
When using a DVD audio disc that includes pictures,
this operation may be permitted in some picture
segments.
Changing the Audio Channel
VCD
Press AUDIO repeatedly during playback to hear a
different audio channel (STEREO, LEFT or RIGHT).
Notes:
• If parental control is set and the disc is not within
the rating settings you must input the password.
(See “LOCK” on page 24.)
• DVDs may have a region code.Your player will not
play discs that have a region code different from
your player. The region code for this player is 2
(two).
1-35
Still Picture and Frame-by-Frame Playback
DVD-A
VCD
Repeat A-B
DivX
DVD-V
DVD-A
VCD
DivX
To repeat a sequence.
1. Press PAUSE/STEP (II) during playback. Advance
the picture frame-by-frame by pressing
PAUSE/STEP (II) repeatedly.
1. Press A-B at your chosen starting point. “ A * ”
appears briefly on the TV screen.
2. To exit still motion mode, press PLAY.
2. Press A-B again at your chosen end point.
“A B” appears briefly on the TV screen and the
repeat sequence begins.
Note:
When using a DVD audio disc that includes pictures,
this operation may be permitted in some picture
segments.
Slow Motion
DVD-V
DVD-A
VCD
DivX
2. Use REW b or FWD f (or SLOW R) to
select the required speed: L 1/16, L 1/8, L
1/4, or L 1/2 (reverse), or R 1/16, R 1/8, R 1/4,
or R 1/2 (forward).
With a DivX Disc and Video CD, the Slow speed
changes: R 1/16, R 1/8, R 1/4 or R 1/2 (forward).
VCD
DivX
DVD Video Discs - Repeat Chapter/Title/Off
• Chapter: repeats the current chapter.
• Title: repeats the current title.
• Off : does not play repeatedly.
Note:
DVD-A
Press INSTANT REPLAY during playback and the
disc will reverse picture search through 10 seconds of
playback. And then the playback will start from the
point again.
VCD
DVD-A
DVD Audio Discs - Repeat Track/Group/Off
• Track: repeats the current track.
• Group: repeats the current Group.
• Off : does not play repeatedly.
Note:
Slow motion playback in reverse is not possible with
Video CDs and DivX Discs..
Random
DVD-V
Video CDs, DivX discs - Repeat Track/All/Off
• Track : repeats the current track
• All : repeats all the tracks on a disc.
• Off : does not play repeatedly.
3. To exit Slow Motion mode, press PLAY (G).
DVD-V
Repeat
You can repeat a title/chapter/all/track/group on a
disc.
Press REPEAT during playback to select a desired
repeat mode.
1. Press SLOW R during playback or still mode.
The player will enter SLOW mode.
One Touch Replay
3. Press A-B again to cancel.
• On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the repeat function (See “PBC” on
page 23).
• If you press SKIP ( ) once during Repeat Chapter (Track)
playback, the repeat playback cancels.
Karaoke DVD
3D Surround
1. Press RANDOM during playback. The unit automatically begins random playback and RANDOM
appears on the TV screen.
2. Press RANDOM again to normal.
DVD-V
DVD-A
VCD
DivX
To produce a 3D surround effect that simulates multichannel audio from two stereo speakers (instead of
the five+ speakers normally required for multi-channel
audio from a home theater system).
Tip:
1. Press DISPLAY during playback.
By pressing SKIP B or F during random playback,
the unit selects another title (track) and resumes Random
playback.
2. Use v or V to select the sound option.
The sound option will be highlighted.
Note:
3. Use F or G to to select “3D SUR”.
To turn off the 3D Surround effect, select
“Normal”.
On a Video CD with PBC, You must set PBC to Off on the
setup menu to use the random function
(See “PBC” on page 23).
1-36
Operation
DVD-V
Time Search
DVD-V
VCD
DivX
Zoom
DVD-V
DVD-A
VCD
DivX
To start playing at any chosen time on the disc:
Use zoom to enlarge the video image.
1. Press DISPLAY during playback. The time search
box shows the elapsed playing time.
1. Press ZOOM during playback or still playback to
activate the Zoom function. The square frame
appears briefly in the right bottom of the picture.
2. Press v / V to select the time clock icon and
“-:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct numbers.
4. Press ENTER/OK to confirm. Playback starts from
the selected time.
2. Each press of the ZOOM button changes the TV
screen in the sequence: 100% size → 400% size
→ 1600% size → screen fit mode → 100% size
Screen fit mode:
You can change the way the image appears on
the screen when you’re playing a DVD movie.
Press v/V to select between Normal, Enhanced,
and Maximum.
3. Use the F G v V buttons to move through the
zoomed picture.
Changing Video Mode
DVD-V
DVD-A
4. To resume normal playback, press ZOOM repeatedly or CLEAR button.
• With certain discs, the playback picture may be
flickering or Dot Crawl is shown on straight lines.
That means Vertical interpolation or De-interlace is
not perfectly matched with the disc. In this case,
the picture quality may be improved by changing
the video mode.
Notes:
• Zoom may not work on some DVDs.
• Screen fit mode is available for playing the DVD disc, VR
disc and movie file.
• To change the video mode, press and hold
DISPLAY about 3 seconds during disc playback.
The new video mode number selected is displayed
on the TV screen. Check whether the video quality
has improved. If not, repeat the above procedure
until picture quality is improved.
• Video mode sequence:
MODE1 → MODE2 → MODE3 → MODE1
• If you turn off the power, the video mode will return
Marker Search
DVD-V
DVD-A
VCD
DivX
To enter a Marker
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears
on the TV screen briefly. Repeat to enter up to nine
markers.
To Recall or Clear a Marked Scene
to initial default state (MODE1).
1. During disc playback, press SEARCH. The marker
search menu appears on the screen.
Detailed Description of each Video Mode
2. Within 10 seconds, press F / G to select a marker
number that you want to recall or clear.
MODE1 : The source material of the DVD video (film material or video material) is determined from disc
information.
MODE2 : Suitable for playing film based content or video
based material recorded by the progressive scan
method.
MODE3 : Suitable for playing video based content with
comparatively little motion.
3. Press ENTER/OK and playback starts from the
marked scene. Or, Press CLEAR and the marker
number is erased from the list.
Note:
The video mode setting only works when the
Progressive Scan option is set to “On” in the Setup
menu.
Screen Saver
4. You can play any marker by inputting its number
on the marker search menu.
The screen saver appears when you leave the
DVD+VCR in Stop mode for about five minutes.
1-37
Special DVD Features
Subtitles
DVD-A
1. Press TOP MENU. If the current title has a menu,
the menu appears on the screen. Otherwise, the
disc menu may appear.
2. The menu offers features such as camera angles,
spoken language and subtitle options, and chapters for the title.
3. Press TOP MENU to exit.
Disc Menu
DVD-V
DVD-A
Press MENU and the disc menu is displayed.
Press MENU again to exit.
Camera Angle
DVD-V
DVD-A
If the disc contains scenes recorded at different camera angles, you can change to a different camera
angle during playback. Press ANGLE repeatedly during playback to select a desired angle. Note that the
number of the current angle appears on the display.
Tip:
The angle indicator will blink on the TV screen during
scenes recorded at different angles as an indication that
angle switching is possible.
Changing the Audio Language
DVD-V
DVD-A
DivX
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
With DVD-RW discs recorded in VR mode that have
both a main and a Bilingual audio channel, you can
switch between Main (L), Bilingual (R), or a mix of
both (Main + Bilingual) by pressing AUDIO.
1-38
Notes:
• This unit can only read subtitle with “.smi”, “.srt” or “.sub”
extension only.
• If there is no information or the unit can not read subtitle
of the DivX file, even if it has subtitle file, “ 1 ” etc. are displayed.
Operation
DVDs may offer menus that allow you to access special features. To use the disc menu, press MENU.
Input the corresponding number or use the F G v V
buttons to highlight your selection. Then press
ENTER/OK.
DVD-V
DivX
Press SUBTITLE repeatedly during playback to see
the different subtitle languages.
Checking the contents of DVD discs: Menus
Title Menu
DVD-V
DVD Audio Discs
1/2
Moving to another GROUP
DVD Audio is a new disc format building on the success of DVD to provide high quality, uncompressed,
multi-channel audio for a new experience in audio
quality. A DVD Audio disc can be identified by the
DVD audio logo on the disc jacket or on the disc
itself.
Some DVD Audio discs divide content into different
groups. Your player enables you to quickly access different groups during playback via the on-screen display.
1. Press DISPLAY during playback or in stop mode.
2. Press v / V to select Group icon.
DVD Audio can provide higher quality stereo than
Audio CDs with a sampling rate of up to 192kHz
(compared to 44.1kHz for CDs). DVD Audio digital
sound can be delivered with up to 24 bits of data
(compared to 16 bits for a standard CD).
3. Press F / G or the numbered buttons (0-9) to
select a group number.
A typical DVD Audio disc contains up to seven times
the data capacity of a CD. This additional space is
used for music, either Advanced Resolution multichannel sound quality that is closer to the artist’s
master recording or for longer recordings. Many DVD
Audio discs contain on-screen text, such as artist
biographies, playlists, or lyrics. Some DVD Audio
discs contain photo galleries or video clips.
Note:
To enjoy maximum sound quality and surround effect
of DVD Audio, you must use the DIGITAL OUT
(OPTICAL or COAXIAL) for your audio connection.
Note:
Sometimes the author of the disc creates hidden content that can only be accessed by entering a password. If the lock icon appears on the TV screen, enter
the password (sometimes you’ll find it on the disc’s
jacket cover or on a web site). This password control
isn’t dictated by your DVD+VCR — it is a function of
the disc.
Since the authoring of DVD Audio Discs varies, some
of the on-screen display choices might not be available for the disc you’re playing.
Viewing another PAGE
1 / 21
Since DVD Audio discs can hold a lot of content,
there are various ways to see what’s available on the
disc.
1. Press DISPLAY during playback.
2. Press v / V to select Page icon.
3. Press
F
/
G
to select a page number.
What appears on the screen will vary from disc to
disc because the information available depends
upon the way the disc was created.
Note:
Since the authoring of DVD Audio Discs varies, some
of the on-screen display choices might not be available for the disc you’re playing.
1-39
The DVD+VCR can play MP3/WMA formatted recordings on CD-ROM, CD-R, or CD-RW discs.
Audio CD
Once you insert an audio CD a menu appears on the
TV screen. Press v / V to select a track then press
PLAY (w) or ENTER/OK and playback starts.
AUDIO CD
1:01:47
1 / 12
List
Program
TRACK01
TRACK02
TRACK03
TRACK04
TRACK05
TRACK06
TRACK07
Clear All
TRACK08
PROGRAM Edit
Operation
MP3 / WMA
1. Press v / V to select a folder, and press
ENTER/OK to see the folder contents.
2. Press v / V to select a track then press PLAY
(w) or ENTER/OK. Playback starts.
This DVD+VCR requires discs and recordings to
meet certain technical standards in order to
achieve optimal playback quality. Pre-recorded
DVDs are automatically set to these standards.
There are many different types of recordable disc
formats (including CD-R containing MP3 or WMA
files) and these require certain pre-existing conditions (see above) to ensure compatible playback.
MUSIC
0:00:00
1 / 104
Program
List
MP3 / WMA disc compatibility with this player is
limited as follows:
• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)
• Bit rate: within 8 - 320kbps (MP3),
32 - 192kbps (WMA)
• The player cannot read an MP3/WMA file that
has a file extension other than “.mp3” / “.wma”.
• CD-R physical format should be ISO 9660
• If you record MP3 / WMA files using software that
cannot create a file system (eg. Direct-CD) it is
impossible to playback MP3 / WMA files. We recommend that you use Easy-CD Creator, which
creates an ISO 9660 file system.
• File names should have a maximum of 8 letters
and must incorporate an .mp3 or .wma extension.
• They should not contain special letters such as /
? * : “ < > l etc.
• The total number of files on the disc should be
less than 650.
1-Music1
2-Music2
3-Music3
4-Music4
5-Music5
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has
no right to grant such permission. Permission
should always be sought from the copyright
owner.
6-Music6
Clear All
7-Music7
DISPLAY
Info
PROGRAM Edit
ID3 TAG
• When playing a file containing information such as track
titles, you can see the information by pressing DISPLAY.
[ Title, Artist, Album, Year, Comment ]
Microsoft, Windows Media, and
the Windows Logo are trademarks
or registered trademarks of
Microsoft Corporation in both the
United States and other countries
• If there is no information, “No ID3 TAG” appear on the
menu screen.
Tips:
• If you are in a file list on the “MUSIC” menu and want to
return to the Folder list, use the v / V to highlight
and press ENTER/OK.
• Press MENU to move to the next page.
• On a CD with MP3/WMA and JPEG you can switch
MP3/WMA and JPEG. Press TOP MENU and “MUSIC” or
“PHOTO” word on top of the menu is highlighted.
1-40
Operation
Playing an Audio CD or MP3/WMA
Disc
Audio CD and MP3 / WMA Disc
Features
Pause
CD
MP3
Random
2. To return to playback, press PLAY w or press
PAUSE/STEP II/R again.
Moving to another Track
Tip:
By pressing SKIP B or F during random playback,
the unit selects another track and resumes random playback.
WMA
1. Press SKIP (B or F) briefly during playback
to go to the next track or to return to the beginning of the current track.
2. Press SKIP B twice in quick successions to go
back to the previous track.
3. You can play any track by inputting its number.
Repeat Track/All/Off
CD
MP3
WMA
2. To return to normal playback, press RANDOM
repeatedly until RANDOM disappears from the
menu screen.
1. Press PAUSE/STEP II/R during playback.
MP3
MP3
1. Press RANDOM during playback. Random
Playback begins immediately and RANDOM
appears on the menu screen.
WMA
CD
CD
Repeat A-B
CD
1. To repeat a sequence during disc playback press
A-B at your chosen starting point. The Repeat
icon and “A” appear on the menu screen.
2. Press A-B again at your chosen end point. The
Repeat icon and “A-B” appear on the menu
screen, and the sequence begins to play repeatedly.
WMA
You can play a track/all on a disc.
3. To exit the sequence and return to normal play,
press A-B again. The Repeat icon disappears
from the menu screen.
1. Press REPEAT when playing a disc. The repeat
icon appears.
2. Press REPEAT to select a desired repeat mode.
• Track: repeats the current track.
• All: repeats all the tracks on a disc.
• Off(No display): does not play repeatedly.
3D Surround
To produce a 3D surround effect that simulates multichannel audio from two stereo speakers (instead of
the five+ speakers normally required for multi-channel
audio from a home theater system).
Note:
If you press SKIP (F) once during Repeat Track playback, the repeat playback will be cancelled.
Search
CD
MP3
CD
1. Press AUDIO during playback.
“3D SUR.” appears on the menu screen.
2. To return to normal playback, press AUDIO
repeatedly until “3D SUR.” disappears from the
menu screen.
WMA
1. Press REW b or FWD f during playback.
2. Press REW b or FWD f repeatedly to select
the required speed: X2, X4, X8 backward or forward.
3. To exit SEARCH mode, press PLAY w.
1-41
Programmed Playback
6. To resume normal playback from pro-
grammed playback, select a track of AUDIO
CD (or MUSIC) list and then press PLAY (w).
1. Insert a disc.
Audio CD or MP3/WMA Discs:
AUDIO CD or MUSIC menu appears.
Repeat Programmed Tracks
2. Press PROGRAM.
2. Press REPEAT to select a desired repeat mode.
1. Press REPEAT when playing a disc. The repeat
icon appears.
The E mark will appear to the right of the word
“Program” on the right side of the menu screen.
• TRACK: repeats the current track
• ALL: repeats all the tracks on programmed list.
• Off(No display): does not play repeatedly.
Note:
Press PROGRAM again, the
the Program Edit mode.
E
mark will disappear to exit
AUDIO CD
1:01:47
If you press F once during Repeat Track playback, the
repeat playback will be cancelled.
MUSIC
1 / 12
0:00:00
List
E
Program
1 / 104
Program
List
TRACK01
TRACK01
TRACK02
TRACK02
1-Music1
2-Music2
TRACK03
TRACK03
2-Music2
3-Music3
TRACK04
TRACK04
3-Music3
4-Music4
TRACK05
TRACK05
4-Music4
5-Music5
TRACK06
TRACK06
5-Music5
6-Music6
TRACK07
1-Music1
Clear All
TRACK08
Edit
Erasing a Track from “Program” List
1. Use v V w to select the track that you wish to
erase from the Program list.
6-Music6
Clear All
7-Music7
PROGRAM
DISPLAY
Audio CD Menu
Info
PROGRAM Edit
2. Press CLEAR. Repeat to erase additional tracks
on the list.
MP3/WMA Menu
Video CD: Press PROGRAM while playback is
stopped. The program menu appears. Press PROGRAM again to exit the menu.
Note:
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the programmed playback (See “PBC” on
page 23).
Erasing the Complete Program List
1. Press w to move to the “Program” list.
2. Use v / V to select “Clear All”, then press
ENTER/OK.
Note:
The programs are also cleared when the disc is removed.
VIDEO CD
List
Note:
Program
TRACK01
TRACK1
TRACK02
TRACK2
TRACK03
TRACK3
TRACK04
TRACK4
E
Clear All
Video CD Menu
3. Select a track on the “List”, then press ENTER/OK
to place the selected track on the “Program” list.
Repeat to place additional tracks on the list.
4. Press w.
Select the track you want to start playing on the
“Program” list.
5. Press PLAY (w) or ENTER/OK to start. Playback
begins in the order in which you programmed the
tracks. Playback stops after all of the tracks on the
“Program” list have played once.
1-42
Operation
The program function enables you to store your
favourite tracks from any disc in the player memory. A
program can contain 30 tracks.
Viewing a JPEG Disc
Zoom
Using this DVD+VCR you can view JPEG files.
Use zoom to enlarge the photo image. (see page 32)
1. Insert a disc and close the tray. The PHOTO menu
appears on the TV screen.
To rotate picture
JPEG
JPEG
Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.
PHOTO
Preview
List
JPEG Folder 1
To listen to MP3/WMA music while watching
JPEG Folder 2
JPEG Folder 3
>>>
JPEG Folder 4
picture
JPEG Folder 5
JPEG Folder 6
JPEG
JPEG Folder 7
You can display files while listening to MP3/WMA
music files recorded on the same disc.
JPEG Folder 8
2. Press v / V to select a folder, and press
ENTER/OK. A list of files in the folder appears. If
you are in a file list and want to return to the previous Folder list, use the v / V buttons on the
remote to highlight
and press ENTER/OK.
3. If you want to view a particular file, press
v / V to highlight a file and press ENTER/OK or
PLAY. The selected file will appear for viewing.
While viewing a file, you can press STOP to move
to the previous menu (PHOTO menu).
Tip:
1. Insert the disc containing the two types of file in
the player.
2. Press TOP MENU to display PHOTO menu.
3. Press v / V to select a photo file.
icon then press ENTER/OK.
4. Use w to select
Playback starts. The playback will continue until
STOP is pressed.
Tip:
To listen to only the desired music while watching picture, programmed the desired tracks from the
“MUSIC” menu and then proceed as above.
• Press MENU to move to the next page.
• There are three Slide Speed options
:
>>> (Fast), >> (Normal), and > (Slow).
Use v V W w to highlight the Speed. Then, use W / w
to select the option you want to use then press
ENTER/OK.
• On a disc with MP3/WMA and JPEG you can switch
MP3/WMA and JPEG. Press TOP MENU and MUSIC or
PHOTO word on top of the menu is highlighted.
• Press RETURN, information of file is hidden.
JPEG disc compatibility with this player is limited as follows:
• Depending upon the size and number of JPEG
files, it could take a long time for the DVD+VCR
to read the disc’s contents. If you don’t see an
on-screen display after several minutes, some of
the files may be too large — reduce the resolution of the JPEG files to less than 2M pixels as
2760 x 2048 pixels and burn another disc.
• The total number of files and folders on the disc
should be less than 650.
Slide Show
JPEG
Use v V W w to highlight the
press ENTER/OK.
Still Picture
(Slide Show) then
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
JPEG
• If the files have “.jpe” or “.jpeg” extensions,
please rename them as “.jpg” file.
1. Press PAUSE/STEP II/R during slide show.
The player will now go into PAUSE mode.
• File names without “.jpg” extension will not be
able to be read by this DVD+VCR. Even though
the files are shown as JPEG image files in
Windows Explorer.
2. To return to the slide show, press PLAY w or
press PAUSE/STEP II/R again.
Moving to another File
• Some discs may be incompatible due to a different recording format or the condition of disc.
JPEG
Press SKIP (B or F) or cursor (W or w) once
while viewing a picture to advance to the next or previous file.
1-43
This unit will play DVD-R/RW discs recorded using
the DVD-Video format that have been finalized using
a DVD-recorder.
• This unit will play DVD-RW discs recorded using
the Video Recording (VR) format.
1. Insert a disc and close the tray. The DVD-VR
menu appears on the TV screen.
2. Press v / V to select a track then press PLAY
(w) or ENTER/OK and playback starts.
3. Press TOP MENU to move to the list menu.
Note:
• Unfinalized DVD-R/RW discs cannot be played in this
player.
• Some DVD-VR disc are made with CPRM data by DVD
RECORDER. Player does not support these kinds of
discs and display the “CHECK DISC”.
What is ‘CPRM’?
CPRM is a copy protection system (with scramble system) only allowing the recording of ‘copy once’ broadcast
programs. CPRM stands for Content Protection for
Recordable Media.
This player is CPRM compatible, which means that you
can record copy-once broadcast programs, but you cannot then make a copy of those recordings. CPRM recordings can only be made on DVD-RW discs formatted in VR
mode, and CPRM recordings can only be played on players that are specifically compatible with CPRM.
1-44
Operation
Playing a DVD VR format Disc
Playing a DivX Movie Disc
DivX disc compatibility with this player is limited
as follows:
Using this DVD+VCR you can play DivX disc.
• Available resolution size of the DivX file is under
720x576 (W x H) pixel.
1. Insert a disc and close the tray. The MOVIE
menu appears on the TV screen.
• The file name of the DivX subtitle is available by
56 characters.
MOVIE
0:00:00
• If there is impossible code to express in the DivX
file, it may be displayed as “ _ ” mark on the display.
List
Movie Folder 1
Movie Folder 2
Movie Folder 3
Movie Folder 4
Movie Folder 5
Movie Folder 6
• If the number of the screen frame is over 30
per 1 second, this unit may not operate normally.
Movie Folder 7
Movie Folder 8
2. Press v / V to select a folder, and press
ENTER/OK. A list of files in the folder
appears. If you are in a file list and want to
return to the Folder list, use the v / V buttons on the remote to highlight
and
press ENTER/OK.
• If the video and audio structure of recorded
file is not interleaved, either video or audio is
outputted.
• If the file is recorded with GMC, the unit supports only 1-point of the record level.
* GMC?
GMC is the acronym for Global Motion Compensation. It
is an encoding tool specified in MPEG4 standard. Some
MPEG4 encoders, like DivX or Xvid, have this option.
There are different levels of GMC encoding, usually
called 1-point, 2-point, or 3-point GMC.
3. If you want to view a particular file, press
v / V to highlight a file and press
ENTER/OK or PLAY (w).
4. Press STOP (Á ) to exit.
Playable DivX file
• “.avi”, “.mpg”, “.mpeg”
Tip:
• Press MENU to move to the next page.
•
On a CD with MP3/WMA, JPEG and MOVIE file, you can
switch MUSIC, PHOTO and MOVIE menu. Press TOP
MENU and MUSIC, PHOTO and MOVIE word on top of
the menu is highlighted.
Playable Codec format
• “DIVX3.xx “, “DIVX4.xx”, “DIVX5.xx”, “XVID”,
“MP43”, “3IVX”.
Playable Audio format
• “AC3”, “DTS”, “PCM”, “MP3”, “WMA”.
- Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA).
- Bit rate: within 8 - 320kbps (MP3),
32 - 192kbps (WMA)
1-45
Additional Operation with tape
Hi-Fi Stereo Sound System (NIC)
Your DVD+VCR will record and playback Hi-Fi stereo
sound. In addition it has a stereo NICAM digital
stereo sound decoder. This allows you to record and
playback the sound in several different ways. Video
cassettes recorded on your DVD+VCR will have a
normal mono audio track and two VHS Hi-Fi stereo
audio tracks. These stereo tracks allow you to make
audio recordings in Hi-Fi stereo or bilingual mode
from a TV broadcast, stereo audio system, video disc
or another Hi-Fi VCR.
1. Your DVD+VCR’s NICAM digital sound decoder
allows you to enjoy broadcasts with NICAM
sound, as well as standard stereo, bilingual and
mono sound. The particular type of sound
received or that recorded will be briefly displayed
on the TV screen for a couple of seconds:
STEREO NICAM
Sound is automatically recorded on the Hi-Fi
stereo and mono tracks of the video tape.
BIL NICAM
Both audio channels will be recorded on the Hi-Fi
stereo tracks. The primary language channel (left)
will be recorded on the mono track of the video
tape.
MONO
The sound is recorded on the Hi-Fi tracks and the
mono track of the video tape without any separation.
2. Press AUDIO repeatedly until the desired audio
mode appears.
3. The choice is STEREO, LEFT, RIGHT and
MONO. In BIL NICAM playback the primary language is output on the left channel and the secondary channel is output simultaneously from the
right channel when audio output is set to
STEREO. The primary language will be output
from both channels when the audio setting is
MONO.
Please note that when adjusting the tracking control Hi-Fi stereo sound may revert to MONO.
Note:
When OFF is selected in NIC, only mono sound will
be output.
The Blank Search enables you to locate the end of
any recording. Whenever a recording creates, a blank
content is recorded on the tape.
Press BLANK SEARCH in the stop mode and it
rapidly advanced to find blank content.
To find next blank content, press BLANK SEARCH
again.
On Screen Display (F.OSD)
You may easily display the current time or tape
counter, amount of tape left, day, month, year, day of
week, programme channel, tape speed and operational mode of your DVD+VCR on the TV screen. If a
recording is taking place these On Screen Displays
will not be recorded onto the tape.
1. Press CLK/CNT to display.
Press CLK/CNT repeatedly to cycle through the
display options. The tape counter and amount of
tape left will appear if there is a tape loaded.
2. After 3 seconds the majority of the On Screen
Displays will clear leaving only the clock or tape
counter and the amount of tape left on the screen.
Press CLK/CNT again to remove all displays from
the TV screen.
Note:
It cannot display when F.OSD is OFF.
Tape Counter Memory Stop
The Digital Tape Counter can be displayed on the display window instead of the time by pressing CLK/CNT
on the remote control. The Digital Tape Counter indicates the relative positions of recordings on the tape.
1. Press CLK/CNT.
Press COUNTER RESET to set the counter to
0:00:00.
Press PLAY w or start recording.
The tape counter will display the actual play time
in hours, minutes and seconds.
2. Press STOP ■ when playback or recording is
complete.
Press REW b.
The tape will rewind and automatically stop when
the counter returns to 0:00:00.
Note:
To rewind to the beginning of the tape, press REW b
again.
1-46
Operation
Blank Search
Video Doctor (Self-Diagnosis)
Wide Screen Compatibility 16:9
This feature informs you that there is a problem with
your DVD+VCR. These error messages will appear
on the TV screen.
Your DVD+VCR can record and play back wide
screen aspect ratio programmes (16:9). To record a
wide screen format programme successfully the correct type of wide screen signal must be broadcast by
the TV station.
1. Press VCR MENU.
Press W or w to select Dr.
Press ENTER/OK.
1. Switch on your DVD+VCR.
Press VCR MENU.
Press F or G to select 16:9/4:3.
Press ENTER/OK.
1 2
Pr-12
REC
P
RSET
ACMS
f OSD
ON
OFF
16:9
4:3
DECODER
+
TIME
DATE
VCR
SYSTEM
Dr.
VCR
Dr.
NIC
-
OPR
OK i
2. Press v or V to check a problem.
1 2
PSET
R
f OSD
16:9
ON
4:3
OFF
REC
Pr-12
ACMS
+
TIME
DATE
VCR
SYSTEM
Dr.
NIC
-
DECODER
16:9
4:3
OK i
OPR
2. Press v/V repeatedly to select: AUTO, 4:3 or
16:9.
AUTO:
Automatically plays back Wide-Screen
programmes as Wide-Screen and Normal
programmes as normal.
4:3
Only for playing back and recording Normal format
recordings (4:3).
16:9:
Only for playing back and recording Wide-Screen format recordings (16:9).
HEAD STATUS
• PLEASE CLEAN:
Clean your video heads.
TAPE STATUS
• NOT RECORDABLE:
Insert a tape with its protection tab in place
NO. OF TIMER PROGRAMME
•2
Shows the number of timer recording.
NEXT TIMER PROGRAMME
• PR-01 26 10:00~11:00 SP
Shows the current status of timer recording.
1 2
REC
PSET
R
f OSD
ON
OFF
Pr-12
ACMS
+
16:9
4:3
-
DECODER
SYSTIME
AUTO
TEM
DATE
4:3 NIC
16:9
OPR
VCR
Dr.
16:9
4:3
i
3. Press VCR MENU to remove the menus from the
TV screen.
3. Press VCR MENU to remove the menus from the
TV screen.
1-47
Recording from another video recorder
With this video recorder you can make recordings
from an external source, such as copying from another video recorder or a camcorder.
Note:
In the following description, this video recorder will be one
used for recording and will be referred to as VCR B. The
other appliance will be used for playback and will be referred
to as VCR A.
1. Press VCR MENU.
The main menu will appear on the TV screen.
Press F or G to select the DECODER.
Press ENTER/OK.
2. Press D or
E to select.
ON: When the decoder is connected to the AV2
socket.
OFF: When another VCR is connected to the AV2
socket.
3. Press VCR MENU to return to a TV picture.
1. VCR A should be connected to the SCART socket
on the rear panel of your unit or the AV jacks on
the front panel of your unit.
2. Insert the recorded tape into VCR A and a blank
tape into VCR B.
3. To start recording, press the REC O on VCR B
and PLAY
G
on VCR A.
4. When you want to finish copying,
Copying from DVD To VCR
This unit allows you to copy the contents of a DVD to
a VHS tape with a press of the REC/OTR button.
press STOP ■ on this video recorder and then
STOP ■ the VCR A.
Note:
Video Head Cleaning
If the DVD you are attempting to copy is copy protected, you
may not be able to copy the disc.
Whenever a video cassette is inserted into or ejected
from your DVD+VCR the video head is automatically
cleaned.
This should mean that additional head cleaning
should not be necessary.
However, dirt accumulating on the head after a long
period of time can cause the playback picture to
become blurred or broken up. High quality video cassette tapes will not normally deposit dirt onto the
video head, but old or damaged tapes might.
1. Insert Disc
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
2. Insert VHS Tape
Insert a blank VHS videotape into the VCR deck.
3. Press DVD so that the DVD indicator lights up.
4. Copy the DVD to VHS Tape
Press the REC O button on the unit front panel.
•
The DVD will go into Play mode and the VCR
will go into Record mode.
•
If the DVD disc menu appears, you may need
to press the Play button manually to begin
copying.
5. Stop the Copy Process.
Press STOP ■.
1-48
Operation
To set the decoder
We have already described, how to connect a
decoder for pay-TV station as DECODER or PREMIERE on page 13-14. For the recording of an
encoded station you do not have to control anything.
You just select the station and wait shortly until the
decoding will start.
Reference
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Country Codes
Choose a country code from this list.
Country
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
Country
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Greenland
Islands
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
Kuwait
Libya
Luxembourg
Code
ET
FJ
FI
FR
DE
GB
GR
GL
HM
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
LU
1-49
Country
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation
Code
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
PY
PH
PL
PT
RO
RU
Country
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Troubleshooting
Cause
Symptom
Correction
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet securely.
The power is on, but
the DVD+VCR does not
work.
DVD or VCR button is not switched
properly.
Refer to page 6.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
The TV is not set to receive DVD+VCR
signal output.
Select the appropriate video input
mode on the TV so the picture from
the DVD+VCR player appears on the
TV screen.
The video cable is not connected
securely.
Connect the video cable into the jacks
securely.
The Progressive Scan is set to On on
the setup menu but is connected to a
standard(analog) television with component video input.
Set Progressive Scan to Off
(see page 22).
Abnormal picture
and/or colour (pinkish,
greenish, etc.).
Mismatch setting between TV and this
unit
Wrong connection.
Select the correct TV output select in
SETUP menu.
Check the connection.
No sound.
The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
The audio cables are not connected
securely.
Connect the audio cable into the jacks
securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The Digital Audio Output is set to the
wrong position.
Set the Digital Audio Output to the
correct position, then turn on the
DVD+VCR again by pressing + / 1.
The disc is dirty.
Clean the disc.
The TV channels are not tuned in properly
Check tuning, carry out tuning again.
Tape heads are dirty.
Clean video heads.
Tape is a rental or was recorded on
another VCR.
Use PR/TRK (+/-) for manual tracking
adjustment while tape is playing.
This unit can only output 625p
Progressive scan picture.
Make sure that your TV can support
625p Progressive scan picture or set
Progressive scan to off.
No picture.
The playback picture is
poor.
1-50
Operation
Check the following guide for the possible cause of a problem before contacting service.
Cause
Symptom
Correction
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type and Regional code.)
The disc is placed upside down.
Place the disc with the playback side
down.
The disc is not placed within the
guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
The Rating level is set.
Cancel the Rating function or change
the rating level.
Video tape cannot be
inserted.
Is the cassette compartment empty?
Eject the tape in.
No Hi-Fi sound
Audio mode is not set properly.
Select STEREO by repeatedly pressing
AUDIO on the remote control.
No NICAM sound
recording
NICAM mode is not set properly.
Make sure NICAM in the menu is set to
AUTO for the station to be recorded.
The remote control
does not work properly.
There is an obstacle in the path of the
remote control and this unit.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
The remote control is not pointed at
the remote sensor of the DVD+VCR.
Point the remote control at the remote
sensor of the DVD+VCR.
The remote control is too far from the
DVD+VCR.
Operate the remote control within 23ft
(7m).
This remote control use the same buttons for VCR and DVD functions
(ex.PLAY).
When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
Camcorder image is
not shown.
Camcorder is off.
Turn camcorder on and operate
properly.
Camcorder image via
AV input to DVD+VCR
is not shown on TV
screen.
DVD+VCR SOURCE SELECT is not
set to AV3.
Press INPUT SELECT to select LINE
input channel AV3.
Timer recording is not
possible.
Clock in DVD+VCR is not set to correct time.
Set clock to correct time. See Setting
the clock Manually on page 16.
Timer has been programmed
incorrectly.
Reprogram Timer. See Timer recording
using On Screen Display on page 27.
Press + / 1 to switch to Timer recording standby mode.
The DVD+VCR does
not start playback.
indicator does not appear.
1-51
Specifications
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Timer
RF Modulator
AC 200-240V, 50Hz
19W
430 X 78.5 X 266 mm (w/h/d)
4.0 kg
5˚C to 35˚C (41˚F to 95˚F)
5 % to 90 %
24 hours display type
UHF 22-68 (Adjustable)
System
Laser
Video Head system
Signal system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
Double azimuth 6 heads, helical scanning.
PAL
DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
More than 100 dB (ANALOG OUT connectors only)
Less than 0.008%
More than 100 dB (DVD)
More than 95 dB (CD)
Inputs (VCR)
Audio
Video
RF IN
-6.0 dBm, more than 10 kohms (SCART)
-6.0 dBm, more than 47 kohms (RCA)
1.0 V (p-p), 75 ohms, unbalanced (SCART/RCA)
PAL B/G, I/I
SECAM D/K
Outputs (DVD)
VIDEO OUT
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (digital audio)
Audio output (optical audio)
Audio output (analog audio)
1.0 V (p-p) 75 ohms, negative sync
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
5.0 V (p-p), 75 ohms, Optical connector x 1
2.0 Vrms (1 kHz, 0 dB), 600 ohms, RCA jack (L, R) x 1/SCART (TO TV)
Outputs (VCR/DVD)
Audio
Video
-6.0 dBm, less than 1 kohms (SCART)
1.0V (p-p), 75 ohms, unbalanced (SCART)
Outputs (DVD)
S-VIDEO OUT
(Y) 1.0 V (p-p) 75 ohms, negative sync., Mini Din 4-pin x 1
(Y) 0.3 V (p-p) 75 ohms
Accessories:
RF 75 Ω Coaxial Cable x 1, Remote control x 1, Batteries (R03/AAA) x 2
Design and specifications are subject to change without notice.
1-52
Reference
General
P/NO: 3834RV0004L
Printed in Indonesia
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement