Datex-Ohmeda S/5TM Compact Anesthesia Monitor S/5TM Compact

Datex-Ohmeda S/5TM Compact Anesthesia Monitor S/5TM Compact
Datex-Ohmeda
S/5TM Compact Anesthesia Monitor
S/5TM Compact Critical Care Monitor
Technical Reference Manual
All specifications are subject to change without notice.
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
Order Code M1021567
March, 2006
Datex-Ohmeda Inc.
P.O. Box 7550
Madison, WI 53707-7550, USA
Tel: +1 608 221 1551
Fax: +1 608 222 9147
GE Healthcare Finland Oy
Helsinki, Finland
P.O. Box 900
FI-00031 GE, FINLAND
Tel: +358 10 39411
Fax: +358 9 1463310
www.gehealthcare.com
Copyright  2006 General Electric Company
Intended purpose (Indications for use)
The Datex-Ohmeda S/5 Compact Anesthesia Monitor with L-CANE05 or L-CANE05A software is intended for
multiparameter patient monitoring with optional patient care documentation.
The S/5 Compact Anesthesia Monitor with L-CANE05 or L-CANE05A software is indicated for monitoring of
hemodynamic (including arrhythmia and ST-segment analysis), respiratory, ventilatory,
gastrointestinal/regional perfusion, Bispectral index (BIS), Entropy (State Entropy and Response Entropy) and
neurophysiological status of all hospital patients.
The S/5 Compact Anesthesia Monitor with L-CANE05 and L-CANE05A software when using BIS is for
monitoring the state of the brain by data acquisition and processing of electroencephalograph signals and may
be used as an aid in monitoring the effects of certain anesthetic agents.
The S/5 Compact Anesthesia Monitor with L-CANE05 or L-CANE05A software is also indicated for documenting
patient care related information.
The S/5 Compact Anesthesia Monitor with L-CANE05 or L-CANE05A software is indicated for use by qualified
medical personnel only.
The Datex-Ohmeda S/5 Compact Critical Care Monitor with L-CICU05 or L-CICU05A software is intended for
multiparameter patient monitoring.
The S/5 Compact Critical Care Monitor with L-CICU05 and L-CICU05A software is indicated for monitoring of
hemodynamic (including arrhythmia and ST-segment analysis), respiratory, ventilatory,
gastrointestinal/regional perfusion, Bispectral index (BIS) and neurophysiological status of all hospital
patients.
The S/5 Compact Critical Care Monitor with L-CICU05 and L-CICU05A software when using BIS is for monitoring
the state of the brain by data acquisition and processing of electroencephalograph signals and may be used as
an aid in monitoring the effects of certain anesthetic agents.
The S/5 Compact Critical Care Monitor with L-CICU05 and L-CICU05A software is indicated for use by qualified
medical personnel only.
Classifications
In accordance with IEC 60601-1
Class I and internally powered equipment – the type of protection against electric shock.
Type BF or CF equipment. The degree of protection against electric shock is indicated by a symbol on each
parameter module.
Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or
nitrous oxide.
Continuous operation according to the mode of operation.
In accordance with IEC 60529
IPX1- degree of protection against harmful ingress of water.
In accordance with EU Medical Device Directive
The Datex-Ohmeda S/5 Compact Anesthesia Monitor is classified as IIb.
In accordance with CISPR 11:
Group 1, Class B
• Group 1 contains all ISM (industrial, scientific and medical) equipment in which there is intentionally
generated and/or used conductively coupled radio-frequency energy which is necessary for the internal
functioning of the equipment itself.
• Class B equipment is suitable for use in domestic establishments and in establishments directly connected
to a low voltage power supply network which supplies buildings used for domestic purposes.
Responsibility of the manufacturer
GE Healthcare Finland Oy (GE) is responsible for the safety, reliability and performance of the product only if:
• modifications, service and repairs are carried out by personnel authorized by GE.
• the electrical installation of the room complies with appropriate requirements.
• the equipment is used in accordance with the User's Guide and serviced and maintained in accordance
with the Technical Reference Manual.
Trademarks
Datex, Ohmeda, S/5, D-lite, D-lite+, Pedi-lite, Pedi-lite+, Mini D-fend, D-fend, D-fend+, OxyTip+, MemCard,
ComWheel, EarSat, FingerSat, FlexSat, PatientO2, Entropy, Patient Spirometry and Tonometrics are trademarks
of GE Healthcare Finland Oy. All other product and company names are property of their respective owners.
A portion of the Entropy software is derived from the RSA Data Security, Inc. MD5 Message-Digest Algorithm.
Master table of contents
Datex-Ohmeda
S/5TM Compact Anesthesia Monitor
S/5TM Compact Critical Care Monitor
Technical Reference Manual, Order code: M1021567
Part I, General Service Guide
Document No.
Updated
Description
M1031517-02
Introduction, System description, Installation,
Interfacing, Functional check, General troubleshooting
1
M1031518-02
Planned Maintenance Instructions
2
Part II, Product Service Guide
Document No.
Updated
Description
M1031519-01
CAM, CCCM Service Menu
1
M1031520-02
Display Unit for F-CM1, F-CMC1 rev. 00...04
F-CMREC1, F-CMCREC1 rev .00...02
Software Licenses L-CANE05(A), L-CICU05(A)
2
M1044470-01
Frame Unit for F-CM1, F-CMC1 rev. 00...04
F-CMREC1, F-CMCREC1 rev. 00...02
AC/DC Power Supply Unit
3
Spare parts
4
M1031521
Table of contents
Table of contents
Table of contents
i
Table of figures
iv
List of tables
vi
About this manual
1
1
3
Introduction
1.1
1.2
2
System description
2.1
2.2
2.3
2.4
2.5
2.6
3
Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1.1
Symbols on transport packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1.2
Symbols on equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1.3
Equipment safety symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.4
Other symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
1.2.1
Safety precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
1.2.2
ESD precautionary procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
1.2.3
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Bus structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Distributed processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Module communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Software loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Parameter modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
System installation
3.1
3.2
3.3
3.4
3.5
3.6
3.7
14
17
Unpacking instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Choosing location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
S/5 Frame for Compact Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3.3.1
Compact Monitor connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.3.2
Connecting to mains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.3.3
Connecting to Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.3.4
Connecting to Wireless Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.3.5
Inserting the parameter modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.3.6
Downloading Monitor Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.3.7
Performing Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.3.8
Installing the Datex-Ohmeda Network and MemCard Upgrade, U-CMMEM . . . . . . . . . . . . .22
3.3.9
Installing the Datex-Ohmeda Network Upgrade, U-CMNET . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.3.10 Installing the S/5 Wireless LAN Upgrade, U-CMW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.3.11 Installing the S/5 Recorder Upgrade, U-CMREC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
S/5 Remote Controller, K-CREMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Anesthesia Record Keeping Keyboard, K-ARKB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
ARK Barcode Reader, N-SCAN (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
3.6.1
Connection to Compact Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
S/5 Compact Airway Modules, E-xxxx / M-xxxxx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
i
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4
3.7.1
3.7.2
Sample gas exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Interfacing
31
4.1
4.2
4.3
4.4
4.5
4.6
4.7
5
Interfacing external monitors via Interface Module, E-INT / M-INT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4.1.1
Connection to external Datex-Ohmeda monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
4.1.2
Connection to Critikon Dinamap 1846SX, Abbott Oximetrix 3 and Baxter Explorer. . . . . . .33
4.1.3
Connection to Baxter Vigilance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
4.1.4
Connection to Nellcor N-100 and N-1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
4.1.5
Connection to Nellcor N-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Interfacing external bedside devices via S/5 Device Interfacing Solutions, N-DISxxx . . . . . . . . . . . . .34
4.2.1
Device Interfacing Solution components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.2.2
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.2.3
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
4.2.4
Selecting the external device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.2.5
Functional check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
4.2.6
Selecting the parameter data source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Interfacing Datex-Ohmeda Anesthesia Delivery Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
4.3.1
Interconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
4.3.2
Setting interfacing parameters on the S/5 Anesthesia Delivery Unit . . . . . . . . . . . . . . . . . .39
4.3.3
Setting interfacing parameters on the S/5 Compact Anesthesia Monitor . . . . . . . . . . . . . .39
Interfacing Dräger Cicero, Cato, Julian and Narkomed 2C (by NAD) . . . . . . . . . . . . . . . . . . . . . . . . . . .40
4.4.1
Interconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
4.4.2
Setting communication parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
4.4.3
Setting interfacing parameters on the S/5 Compact Anesthesia or Compact Critical Care
Monitor41
Interfacing printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
4.5.1
Setting S/5 Compact Monitor interface for printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
4.5.2
Connection to serial printers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
4.5.3
Connection to parallel printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
4.5.4
Installing the Serial-to-Parallel Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
4.5.5
Connection to printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Interfacing computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Output signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
4.7.1
Digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
4.7.2
Analog outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
4.7.3
S/5 Pressure Temp Module, E-PT or M-PT, output signals . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Functional check
5.1
5.2
5.3
47
Recommended tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
5.1.1
Hemodynamic patient simulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Functional inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
5.3.1
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
5.3.2
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
5.3.3
Keyboard(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
5.3.4
Frame unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
5.3.5
Display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
5.3.6
Compact Airway Module, E-CXXXXX/ M-CXXXXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
5.3.7
Single width Airway Module, E-miniC/ M-miniC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
ii
Document no. M1031517-02
Table of contents
5.3.8
5.3.9
5.3.10
5.3.11
5.3.12
5.3.13
5.3.14
5.3.15
5.3.16
5.3.17
5.3.18
5.3.19
5.3.20
5.3.21
5.3.22
5.3.23
5.3.24
6
Tonometry Module, E-TONO/ M-TONO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Multiparameter Hemodynamic Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Pressure/Pressure Temp Modules, E-P, E-PT, M-P, M-PT. . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Dual pressure Module, E-PP/ M-PP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Cardiac Output Modules, E-COP/ M-COP, E-COPSv/ M-COPSv . . . . . . . . . . . . . . . . . . . . . .55
NIBP module, M-NIBP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Nellcor Compatible Saturation module, E-NSAT/ M-NSAT . . . . . . . . . . . . . . . . . . . . . . . . . .56
Datex-Ohmeda Oxygen Saturation module, M-OSAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
BIS Module, E-BIS/ M-BIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Entropy Module, E-ENTROPY/ M-ENTROPY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Data Card and Menu Card function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Network connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Wireless Network Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Interface Module, E-INT/ M-INT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Device Interfacing Solution, N-DISxxx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
General troubleshooting
59
Appendix A: Functional check form, Datex-Ohmeda S/5 CAM, CCCM
A-1
Appendix B: ElectroMagnetic Compatibility
B-1
iii
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Table of figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
S/5 Compact Anesthesia Monitor system ............................................................................................. 3
General bus structure of S/5 system................................................................................................... 14
Principle of UPI section operation ....................................................................................................... 15
General structure of parameter modules with patient isolation............................................................. 16
External connections of Compact Monitor frame F-CM(C)1 rev.04 ........................................................ 18
External connections of Compact Monitor frame F-CM(C)1 rev.00...03................................................. 19
Installation of the U-CMREC1 ............................................................................................................. 24
ARK Barcode Reader, N-SCAN connected to Compact Monitor ............................................................ 25
Compact Airway Module, E-XXXX......................................................................................................... 26
Scavenging through ventilator reservoir............................................................................................... 27
Connecting the gas module to the scavenging connector of S/5 Avance .............................................. 27
Sample gas returned to patient circuit in ADU ..................................................................................... 28
Connection cables and LED indicators ................................................................................................ 36
An example of interfacing external devices with Device Interfacing Solution.......................................... 37
Connecting S/5 Compact Monitor to printer, converter model PI130-R2 .............................................. 43
Connecting S/5 Compact Monitor to printer, converter model PI 1115A............................................... 44
S/5 Compact Monitor general troubleshooting flowchart..................................................................... 59
iv
Document no. M1031517-02
Table of figures
v
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
List of tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Transference of parameters, Datex-Ohmeda monitors ............................................................ 32
Transference of parameters, external monitors ....................................................................... 32
DIS modules and interfaced devices...................................................................................... 34
Parameters transferred from S/5 Compact Anesthesia Monitor to S/5 Anesthesia
Delivery Unit ......................................................................................................................... 39
Events transferred from S/5 Anesthesia Delivery Unit to the S/5 Compact Anesthesia Monitor 40
Parameters transferred from Dräger Cicero monitor to S/5 Compact Anesthesia Monitor or
S/5 Compact Critical Care Monitor ........................................................................................ 41
Parameters transferred from Dräger Cato, Julian and Narkomed 2C (NAD) monitor to the S/5
Compact Anesthesia Monitor or S/5 Compact Critical Care Monitor ....................................... 42
Coding element connector, X4............................................................................................... 45
Synchronization connector, X8 .............................................................................................. 45
Signal output connector pin assignments .............................................................................. 46
Patient simulators’ compatibility with each hemodynamic module.......................................... 49
Adapter cables for hemodynamic patient simulators .............................................................. 50
Guidance and manufacturer’s declaration – electromagnetic emissions ................................B-1
Guidance and manufacturer’s declaration – electromagnetic immunity .................................B-2
Guidance and manufacturer’s declaration – electromagnetic immunity .................................B-3
Recommended separation distances between portable and mobile RF communications
equipment and the S/5™ CAM/ CCCM.................................................................................B-5
vi
Document no. M1031517-02
About this manual
Notes to the reader
This Technical Reference Manual is intended for service personnel and engineers who will install,
service and maintain Datex-Ohmeda S/5 Compact Anesthesia Monitors running the software
license L-CANE05 or L-CANE05A and S/5 Compact Critical Care Monitors running the software
license L-CICU05 or L-CICU05A. As the monitor setup may vary, some functions described may not be
available in the monitor you are using.
•
The order code for the entire printed manual is M1021567. The manual includes Technical
Reference Manual Slots and every slot has an individual document number.
•
Part I gives the reader an overview of the monitor. It contains the information needed to install,
interface and troubleshoot the monitors. Instructions for functional check and planned
maintenance are also included. Read the manual through and make sure that you understand
the procedures described before the installation of the monitor. To avoid risks concerning safety
or health, strictly observe the warning indications. If you need any assistance concerning the
installation, please do not hesitate to contact your authorized distributor.
•
Part II contains detailed descriptions of each component of the S/5 CAM, CCCM Monitor,
For information of parameter modules, Remote Controller and Device Interfacing Solution refer to the
“S/5 E-Modules, Technical Reference Manual”. Service check for each of these products is included
in these slots.
The manufacturer reserves the right to change product specifications without prior notice. Although
the information in this manual is believed to be accurate and reliable, the manufacturer assumes no
responsibility for its use.
Installation and service are allowed by authorized service personnel only.
GE Healthcare Finland Oy (GE) assumes no responsibility for the use or reliability of its software in
equipment that is not furnished by GE.
Related documentation
S/5 Modules
S/5 E-Modules, Technical Reference Manual
S/5 M-Modules, Technical Reference Manual
S/5 Compact Anesthesia Monitor
For instructions for daily use including cleaning and daily maintenance, clinical aspects and basic
methods of measurement see:
S/5 Compact Anesthesia Monitor, User’s Guide
S/5 Compact Anesthesia Monitor, User’s Reference Manual
S/5 Compact Critical Care Monitor
For instructions for daily use including cleaning and daily maintenance, clinical aspects and basic
methods of measurement:
S/5 Compact Critical Care Monitors, User’s Guide
S/5 Compact Critical Care Monitors, User’s Reference Manual
For more information about the iCentral, S/5 Arrhythmia Workstation and anesthesia record keeping
solution, see the “Technical Reference Manuals” and “User’s Reference Manuals” for these products.
1
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Software options and default settings are described in the “Default Configuration Worksheet”
delivered with each monitor.
Available accessories are described in the “Supplies and Accessories” catalog delivered with each
monitor.
Conventions used
To help you find and interpret information easily, the manual uses consistent text formats:
"
Sign the check form after performing the procedure.
Hard Keys
Names of the hard keys on the Remote Controller, Command Board, side panel and modules are
written in the following way: Others.
Menu Items
Hypertext links
WARNING
Software terms that identify window parts or menu items are written in bold italic: ECG Setup.
Menu access is described from top to bottom. For example, the selection of the Monitor Setup hard
key, the Screen 1 Setup menu item and the Waveform Fields menu item would be shown as
Monitor Setup - Screen 1 Setup - Waveform Fields.
Messages (alarm messages, informative messages) displayed on the screen are written inside single
quotes: ‘Please wait’.
When referring to different sections in this manual or to other manuals, manual names and section
names are enclosed in double quotes:
See section "Cleaning and care."
Please refer to "iCentral User's Reference Manual: Alarms."
Hypertext links on PDF versions are written in blue color.
Warnings are written in the following way:
WARNING
This is a WARNING.
CAUTION
Cautions are written in the following way:
CAUTION
This is a CAUTION.
NOTE
Notes are written in the following way:
‘Messages’
“Sections”
NOTE: This is a NOTE.
In this manual, the word “select” means choosing and confirming.
Illustrations and names
All illustrations in this manual are only examples, and may not necessarily reflect your system
settings or data displayed in your system. If a particular selection is not available in your system, the
selection is shown grayed.
2
Document no. M1031517-02
Introduction
1
Introduction
The modular design makes the system flexible and easy to upgrade. In addition to patient parameter
modularity and easy upgrades, the monitor can be upgraded to anesthesia record keeping, wired
and wireless networking and memory card operation. Additionally, external devices can be interfaced
to the monitor with interface modules.
NOTE: Your system may not include all these components. Consult your local representative for the
available components.
1
5
Figure 1
(1)
(2)
(3)
(4)
(5)
3
2
4
S/5 Compact Anesthesia Monitor system
S/5 Compact Anesthesia Monitor with modules inside
Remote Controller, K-CREMCO
Printer
Wireless Network (WLAN) Access Point, N-WAP
Network (LAN)
Optional components
Optional components are:
•
•
•
•
Built-in recorder, N-CMREC1
Remote controller
Keyboard for anesthesia record keeping solution, barcode reader
Wireless network option, N-CMW
Possible software options are:
•
MemCard option, N-CMMEM
NOTE: Insert the WLAN PC card in the first slot from the front.
NOTE: Memory Module, M-MEM/ E-MEM, is not compatible with the S/5 Compact Monitors.
3
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Communication between monitors
You can use the Compact Monitor as a stand-alone monitor or for
−
viewing and receiving data (alarms, vital signs) from other patient monitors
−
gathering and storing data during transportation.
To view other patient monitors, the monitor needs to be connected to the network (LAN or WLAN). To
gather, store, and transfer data between different Datex-Ohmeda monitors, use memory cards or
connect the monitor to the network.
NOTE: With WLAN, use only Data Card.
4
Document no. M1031517-02
Introduction
1.1
Symbols
1.1.1
Symbols on transport packaging
The contents of the transport package are fragile and must be handled with care.
Indicates the correct upright position of the transport package.
The transport package must be kept in a dry environment.
Indicates the temperature limitations within which the transport package should be
stored.
1.1.2
Symbols on equipment
This battery contains Ni-MH and can be recycled.
Ni-MH
Pb
Dangerous voltage.
When using the ARK Barcode Reader, N-SCAN, do not stare into beam. The N-SCAN
Barcode Reader is a Class 2 laser product.
5
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.1.3
Equipment safety symbols
-
Attention, consult accompanying documents.
When displayed next to the O2 value, indicates that the FiO2 low alarm limit is set
below 21%.
- When displayed next to the HR value, indicates that the pacer is set on R.
-
On the modules or frames indicates that modules with identical measurements
should not be used in the same monitor. If such modules have been inserted,
remove the module that has been most recently connected. You can also remove
both modules and re-connect the new module after five seconds.
-
On the Interface Module E-INT, M-INT, indicates that it is for connecting external
devices. Do not connect patient cables to the module.
- On the E-TONO, M-TONO module indicates that the module should only be used
with Tonometrics catheters.
- On the E-miniC module indicates that airway gases should be calibrated every six
months in normal use and every two months in continuous use.
6
Document no. M1031517-02
-
BIS: On the Aspect DSC indicates that the converter must not be opened for any
reason or autoclaved.
-
On the E-PRESTN, E-PRETN, E-RESTN, E-PSM, E-PSMP, E-P, E-PP, E-PT, E-COP and
E-COPSv module indicates that protection against cardiac defibrillator discharge
is due in part to the accessories for pulse oximetry (SpO2), temperature (T) and
invasive pressure (P) measurement.
-
On the E-NMT, M-NMT module indicates the following warnings:
* Do not place the NMT stimulating electrodes on the patient’s chest.
* Always stop the NMT measurement before handling the stimulating electrodes.
* Never subject a patient with an implanted electronic device to electrical
stimulation without consulting a medical specialist first.
-
On the rear or bottom panel this symbol indicates the following warnings and
cautions:
* Electric shock hazard. Do not open the cover or the back. Refer servicing to
qualified service personnel.
* For continued protection against fire hazard, replace the fuse only with one of
the same type and rating.
* Do not touch a battery-operated monitor during defibrillation procedure.
* Disconnect from the power supply before servicing.
* Do not use the monitor without manufacturer approved mounting attached.
Introduction
Type BF (IEC 60601-1) protection against electric shock.
Type BF (IEC 60601-1) defibrillator-proof protection against electric shock.
Type CF (IEC 60601-1) protection against electric shock.
Type CF (IEC 60601-1) defibrillator-proof protection against electric shock.
When displayed in the upper left corner of the screen, indicates that the alarms are
silenced. When displayed in the menu or digit fields, indicates that the alarm source
has been turned off or alarm does not meet the alarm-specific activation criteria.
ESD warning symbol for electrostatic sensitive devices. Pins of connectors identified
with the ESD warning symbol should not be touched. Connections should not be
made to these connectors unless ESD precautionary procedures are used. For
details, see section “1.2.2. ESD precautionary procedures”.
Symbol for non-ionizing electromagnetic radiation. Interference may occur in the
vicinity of equipment marked with this symbol.
1.1.4
Other symbols
Equipotentiality. Monitor can be connected to potential equalization conductor.
Alternating current
Fuse. Replace the fuse only with one of the same type and rating.
SN, S/N
Serial Number
Battery operation and remaining capacity (green bar)
Battery charging (white bar)
Submenu. Selecting an alternative marked with this symbol in a menu opens a new
menu.
7
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
The monitor is connected to the network (LAN).
The monitor is connected to the wireless network (WLAN).
Data Card (green) and/or Menu Card (white) is inserted.
WLAN signal strength. The number of segments corresponds to the signal strength:
four segments indicate strong signal, one segment weak signal. When connection to
access point is being searched, the segments scroll from zero to four and back.
A blinking heart next to the heart rate or pulse rate value indicates the beats
detected.
A lung next to the respiration rate value indicates that respiration rate is calculated
from the impedance respiration measurement.
Gas inlet
Gas outlet
Do not reuse.
Use by. Indicates the last use day.
Date of manufacture
Do not immerse the sensor in liquids.
8
Document no. M1031517-02
Introduction
IPX class:
IPX0
IPX1
IPX2
IPX3
IPX4
IPX7
IPX8
Degree of protection against harmful ingress of water as detailed in the
IEC 60529:
- Ordinary equipment
- Protection against vertically falling water drops.
- Protection against vertically falling water drops when enclosure tilted up to 15 °.
- Protected against spraying water.
- Protected against splashing water.
- Protected against the effects of temporary immersion in water.
- Protected against the effects of continuous immersion in water.
This symbol indicates that the waste of electrical and electronic equipment must not
be disposed as unsorted municipal waste and must be collected separately. Please
contact an authorized representative of the manufacturer for information concerning
the decommissioning of your equipment.
Ethernet connector
9
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.2
Safety
The following list contains general warnings and cautions you should know before installing,
maintaining or servicing the system. Warnings and cautions specific to the use of the system can be
found in the User’s Guide and User’s Reference Manual.
1.2.1
Safety precautions
Warnings
WARNING
A WARNING indicates a situation in which the user or the patient may be in
danger of injury or death.
Power connection
• Use only hospital-grade grounded power outlets and power cord. Do not remove the grounding
pin from the power plug.
•
Use only an intact power cord. Replace the power cord if it is cracked, frayed, broken or
otherwise damaged.
•
•
•
Do not apply tension to the power cord otherwise the cord may get damaged.
•
•
•
Do not use extension cords or adapters of any type.
Before starting to use the system, ensure that the whole combination complies with the
international standard IEC 60601-1-1 and with the requirements of the local authorities. Do
not connect any external devices to the system other than those specified.
If the integrity of the external protective earth conductor arrangement is in doubt, use the
monitor with battery operation.
To avoid the risk of electric shock, this equipment must only be connected to a supply mains
with protective earth.
Do not use an additional multiple socket outlet or extension cord.
Installation
• Keep the monitor horizontal when the Compact Airway Module is used. Tilting the monitor may
cause erroneous results in the Compact Airway Module’s readings and damage the module.
•
•
•
The monitor or its components should not be used adjacent to or stacked with other equipment.
If adjacent or stacked use is necessary, the monitor and its components should be observed to
verify normal operation in the configuration in which it will be used.
Pins of connectors identified with the ESD warning symbol should not be touched. Connections
should not be made to these connectors unless ESD precautionary procedures are used. For
details, see section “1.2.2. ESD precautionary procedures”
After transferring or reinstalling the monitor, always check that it is properly connected and all
parts are securely attached. Pay special attention to this in case of stacked mounting.
•
•
Never install the monitor so that it is above the patient.
•
If you accidentally drop the monitor, modules or frames, have them checked by authorized
service personnel prior to clinical use.
A printer or computer must be supplied from an additional transformer providing at least basic
isolation (isolating or separating transformer).
10
Document no. M1031517-02
Introduction
Laser radiation
• When using the ARK Barcode Reader, N-SCAN, do not stare into the beam. The N-SCAN is a
Class 2 laser product.
External connection
• Do not connect any external devices to the monitor other than those specified.
Fuse replacement
• Replace a fuse only with one of the same type and rating.
Explosion hazard
• Do not use the monitor in the presence of flammable anesthetics.
Patient safety
• Do not perform any testing or maintenance on the monitor while it is being used on a patient.
• PACEMAKER PATIENTS: The impedance respiration measurement may cause rate changes in
Minute Ventilation Rate Responsive Pacemakers. In this case, set the pacemaker rate
responsive mode off or turn the monitor impedance respiration measurement off.
•
•
•
Never install the monitor so that it is above the patient.
The monitor must not be used without manufacturer approved mounting attached.
Operation of the monitor outside the specified values may cause inaccurate results.
Cleaning and service
• Only trained personnel with proper tools and test equipment should perform the tests and
repairs described in this manual. Unauthorized service may void the monitor warranty.
•
Turn the power off and unplug the power cord before cleaning or service. Completely remove
any moisture before reconnecting the power cord to the mains outlet.
•
Do not touch any exposed wire or conductive surface while any cover is removed and the
monitor is energized. The voltages present can cause injury or death.
•
Pins of connectors identified with the ESD warning symbol should not be touched. Connections
should not be made to these connectors unless ESD precautionary procedures are used. For
details, see section “1.2.2. ESD precautionary procedures”.
•
Always perform an electrical safety check and a leakage current test on the monitor after
service.
Accessories
• Use only accessories, including mounts and batteries, and defibrillator-proof cables and
invasive pressure transducers approved by GE Healthcare. For a list of approved supplies and
accessories, see the “Supplies and Accessories” catalog delivered with the monitor. Other
cables, batteries, transducers and accessories may cause a safety hazard, damage the
equipment or the system, result in increased emissions or decreased immunity of the
equipment or system or interfere with the measurement. Protection against cardiac defibrillator
discharge is due in part to the accessories for pulse oximetry (SpO2), temperature (T) and
invasive pressure (P) measurement.
11
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
•
Single use accessories are not designed to be reused. Reuse may cause a risk of contamination
and/or affect the measurement accuracy.
Cautions
CAUTION
A CAUTION indicates a condition that may lead to equipment damage or malfunction.
Installation
• Leave space for air circulation to prevent the monitor from overheating.
• Before connecting the power cord to the power supply, check that the local voltage and
frequency correspond with the rating stated on the device plate.
Before use
• Allow two minutes for warm-up and note any error messages or deviations from normal
operation.
•
Do not connect a sampling line to the female Patient Spirometry connector while the other end
of the sampling line is connected to the D-fend water trap. The pressure in the gas sampling
system may cause damage to the PVX unit pressure transducers.
Autoclaving and sterilizing
• Do not autoclave any part of the monitor.
• Do not gas sterilize the modules.
Cleaning and service
• Do not use hypoclorite, ammonia-, phenol-, or acetone based cleaners. These cleaners may
damage the monitor surface.
•
Do not immerse any part of the device in any liquid, or allow liquid to enter the monitor or
modules.
•
•
Do not apply pressurized air to any outlet or tubing connected to the monitor.
•
•
Do not break or bypass the patient isolation barrier when testing PC boards.
Electrostatic discharge through the PC boards may damage the components. Before handling
PC boards, wear a static control wrist strap. Handle all PC boards by their non-conductive edges
and use anti-static containers when transporting them.
Do not clean the spirometry tubes with high pressure air or O2 flushing while the spirometry
tubes are connected to Patient Spirometry connector. High differential pressure may damage
PVX unit pressure transducers.
Special components
• Special components are used in these monitors that are vital to assure reliability and safety. GE
Healthcare assumes no responsibility for damage, if replacement components not approved by
GE Healthcare are used.
• A lithium battery on the CPU Board. Dispose of the faulty IC containing the battery according to
local regulations.
Batteries
To replace the batteries safely, please refer to the service instructions in this manual.
12
Document no. M1031517-02
Introduction
•
Do not short-circuit the battery terminals, this may produce a very high current, which will
damage the battery.
•
•
Do not dispose of the battery into open flame, nor put the battery near fire, as it may explode.
Do not dismantle the battery.
See also section “Symbols”.
Storage and transport
Do not store or transport the monitor outside the specified temperature, pressure and humidity
ranges:
Temperature
-10...+50 °C/14...122 °F
Atmospheric pressure
660...1060 hPa/500...800 mmHg/660...1060 mbar
Relative humidity
10...90% noncondensing
For display specific environmental requirements see specifications in the “Display” slot.
1.2.2
ESD precautionary procedures
•
•
To avoid electrostatic charges building up, it is recommended to store, maintain and use the
equipment at a relative humidity of 30% or greater. Floors should be covered by ESD dissipative
carpets or similar. Non-synthetic clothing should be used when working with the component.
To prevent applying a possible electrostatic discharge to the ESD sensitive parts of the
equipment, one should touch the metallic frame of the component or a large metal object
located close to the equipment. When working with the equipment and specifically when the
ESD sensitive parts of the equipment may be touched, a grounded wrist strap intended for use
with ESD sensitive equipment should be worn. Refer to the documentation provided with the
wrist straps for details of proper use.
ESD precautionary procedure training
It is recommended that all potential users receive an explanation of the ESD warning symbol and
training in ESD precautionary procedures.
The minimum contents of an ESD precautionary procedure training should include an introduction to
the physics of electrostatic charge, the voltage levels that can occur in normal practice and the
damage that can be done to electronic components if they are touched by an operator who is
electrostatically charged. Further, an explanation should be given of methods to prevent build-up of
electrostatic charge and how and why to discharge one’s body to earth or to the frame of the
equipment or bond oneself by means of a wrist strap to the equipment or the earth prior to making a
connection.
1.2.3
Disposal
Dispose of the whole device, parts of it and its packing material in accordance with local
environmental and waste disposal regulations.
13
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2
System description
2.1
Introduction
Datex-Ohmeda monitors build up a freely configurable modular system. The architecture is designed
to enable different module combinations so that the user is able to get the desirable parameter and
feature set. This modular approach makes it possible to add new features when they are needed.
2.2
Bus structure
Patient
Patient
Patient
Modules
Module
Module
MODULE-BUS
PCMCIA
Serial
Ethernet
Sound
UPI
Code
Memory
Chipset
DRAM
Display
Controller
486 LOCAL BUS
NonVolatile
Memory
Reset
Logic
Figure 2
Boot
Memory
486
Processor
cam_p1_gnrl_bus_strctr_cm.vsd
ISA-BUS
General bus structure of S/5 system
The CPU bus is a communication channel used only for internal data transfer. It is based on the ISA
bus used in IBM PC computers. Data is transferred on this 16 bit wide bus using the CPU clock
frequency.
The module bus is for the parameter modules. The bus is based on the industry standard RS-485,
which uses a differential serial method to transfer data. This type of bus is robust and it allows
parameter modules to be inserted or removed while the power is on. The module bus uses a 500 kbps
data transfer rate.
The RS-485 type of serial communication supports so-called multidrop or party line connections. This
means that all parameter modules connected to the module bus use exactly the same lines for
communication. The advantage of this is that all bus connectors are identical and the modules can be
connected in any order and position.
14
Document no. M1031517-02
System description
2.3
Distributed processing
A system assembled from S/5 products is a multiprocessor system. All parameter modules have their
own microprocessor, which performs functions such as module key control, waveform filtering,
parameter related computing and pneumatic control, etc. At the same time the main CPU performs
higher level tasks such as trending and alarm control. While the parameter modules and CPU are
performing their tasks, the UPI (Universal Peripheral Interface) microprocessor handles all functions
needed to transfer data between the parameter modules and the CPU.
This kind of parallel processing gives one major advantage to centralized processing. When new
parameter modules are added to the system, the processing power is increased. As a result, the
system does not slow down when new features are added.
Module communication
The communication master controlling data transfers between the CPU and parameter modules is
called UPI processor. It sends data to each connected module 100 times a second. Modules respond
to each data request immediately by sending a data package, whose length depends on the type of
the module. This communication protocol ensures that each module receives and sends data every
10 ms. If a module does not respond to data requests, the UPI processor presumes that the module is
disconnected.
Parameter modules may hold a static (fixed) or dynamic address, which the UPI processor uses when
sending out data. Two parameter modules of the same type must not be fitted onto the same monitor
since they might reply to a data request simultaneously, thus causing communication errors.
Temp
Meas
Shared
SRAM
Control
Logic
Analog & Digital outputs
UPI
Processor
Module Bus
ComWheel Interface
Keypad Interface
Figure 3
cam_p1_prncpl_UPI_operation.vsd
Voltage
Meas
ISA-BUS
2.4
Principle of UPI section operation
The UPI processor collects and stores all data that is received from the parameter modules into a
shared SRAM, which is mapped directly to the address space of the main CPU. The main CPU reads
data from the memory while the UPI processor guarantees that the data is up to date. This operation
also works in the other direction. In this the main CPU fills the shared SRAM with data and the UPI
processor distributes it to the parameter modules.
15
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.5
Software loading
The program memory on the CPU board is loaded with monitor software at the factory. The software is
used for running all the functions that are integrated into the PC board. For service and upgrade
procedures, the CPU board is fitted with a PCMCIA card drive through which new software can be
loaded.
Parameter modules
A/D
converter
CPU
RAM
EEPROM
Peripheral
drivers
Figure 4
Isolation
transformer
Opto
isolation
+13...16 V
VMOD
Data
RS485
drivers
general_struct_of_parm_mod.vsd
Analog
electronics
+5 V
+12 V
Module Bus
PATIENT
Module
keys
Patient isolation
2.6
General structure of parameter modules with patient isolation
The detailed structure of a parameter module depends on the specific needs for each individual
parameter. However, some common parts are used in the parameter modules. The electronics inside
the module is usually divided into isolated (floating) and non-isolated sections. Typically, the
non-isolated section consists of buffers to interface the parameter module to the module bus while
the rest of the electronics is located in the isolated section. The isolated section includes the
microcontroller together with memory components, the front-end analog electronics (amplifiers, etc.)
and sensor drivers.
16
Document no. M1031517-02
System installation
3
System installation
3.1
Unpacking instructions
1.
2.
3.
4.
3.2
Confirm that the packing box is undamaged. If the box is damaged, contact the shipper.
Open the top of the box and carefully unpack all components.
Confirm that all components are undamaged. If any of the components are damaged, contact
the shipper.
Confirm that all components are included. If any of the components are missing, contact your
GE Healthcare distributor.
Choosing location
Consider the following aspects:
•
•
•
•
lighting
•
environment
space
connections
electromagnetic and radio frequency interference, see Appendix B. ElectroMagnetic
Compatibility
WARNING
The monitor or its components should not be used adjacent to or stacked with
other equipment. If adjacent or stacked use is necessary, the monitor and its
components should be observed to verify normal operation in the configuration in
which it will be used.
WARNING
Never install the monitor so that it is above the patient.
CAUTION
The monitor display is fragile. Ensure that it is not placed near a heat source or
exposed to mechanical shocks, pressure, moisture or direct sunlight.
3.3
S/5 Frame for Compact Monitor
Mounting of S/5 Compact Monitor to the Bed Mount, Wall Mount or Roll Stand is described in a
separate instruction sheet delivered with each mount.
WARNING
After transferring or reinstalling the monitor, always check that it is properly
connected and all parts are securely attached. Pay special attention to this in
case of stacked mounting.
17
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.3.1
Compact Monitor connections
9
1
11
10
12
2
3
4
14
8
5
13
6
7
Figure 5
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
External connections of Compact Monitor frame F-CM(C)1 rev.04
Air filter
NET connector
NET ID connector (not used with N-CMW)
Recorder (optional)
SYNC connector
Connector for external keyboard (anesthesia record keeping solution keyboard), K-CREMCO or
Barcode Reader
Potential equalization
Serial port
Receptacle for power cord
WLAN PC card LED
WLAN PC card
Slot for Memory Cards (PCMCIA) and WLAN PC card
Connector for Device Interfacing Solution
Modules
NOTE: Insert the WLAN PC card in the first PC card slot from the front.
18
Document no. M1031517-02
System installation
11
11
1
10
9
14
13
2
12
8
3
4
5
7
6
Figure 6
External connections of Compact Monitor frame F-CM(C)1 rev.00...03
(1)
(2)
(3)
(4)
(5)
Dust filters
Recorder unit (optional)
Connector for factory use only
Synchronization connector
Connector for external keyboard (anesthesia record keeping solution keyboard), K-CREMCO or
Barcode Reader
(6) Potential equalization connector
(7) Serial port connector
(8) Receptacle for power cord
(9) NET ID connector
(10) NET connector
(11) WLAN antenna cover (optional)
(12) Connector for Device Interface Solution
(13) WLAN antenna card LED
WLAN antenna card (optional)
CAUTION
Switch the power to standby before making any connections.
19
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.3.2
Connecting to mains
Connect the power cord to the mains power inlet on the side of the power supply unit and to the wall
socket.
NOTE: Before taking the monitor into use for the first time, the batteries should be fully charged. Keep
the monitor connected to the mains until the Battery charging symbol disappears, or in STBY mode
the Stby LED stops blinking (may take up to 10 hours if the batteries are fully discharged).
WARNING
3.3.3
The power cord may only be connected to a three-wire, grounded, hospital grade
receptacle.
Connecting to Network
Make sure that the Datex-Ohmeda Network Option, N-CMNET or S/5 MemCard and Network Option,
N-CMMEM is installed.
NOTE: With L-CANE03(A) and L-CICU03(A) or newer software, the N-CMNET option is automatically
installed.
Use the Monitor-Network cable to connect the monitor to the network.
1. Make sure that the power is switched off.
2. Connect the Identification Plug and one RJ-45 connector to the connectors X4 and X5.
3. Connect the other RJ-45 connector to the corresponding connector on the wallbox.
4. Switch on the power. Confirm that the network symbol and 'Connected to Network' message
are displayed on the upper part of the screen.
3.3.4
Connecting to Wireless Network
Make sure that the S/5 Wireless LAN Option, N-CMW and the antenna cover are installed. Use the
wireless LAN antenna card to connect the monitor to the network.
NOTE: The N-CMW option requires also that either N-CMNET or N-CMMEM option is installed.
1.
2.
3.
Make sure that the power is switched off.
Connect the wireless LAN antenna card into the foremost card drive slot.
Switch on the power. Confirm that the wireless LAN network symbol and the wireless LAN signal
strength symbol are displayed on the upper part of the screen.
20
Document no. M1031517-02
System installation
3.3.5
Inserting the parameter modules
Insert each plug-in parameter module into a module slot. Firmly press the module in position.
NOTE: Ensure that the module is properly oriented (i.e. the module release latch is facing downward).
Do not use two or more modules with identical functions in the monitor.
Modules with identical functions are:
3.3.6
•
Hemodynamic multiparameter modules, E-PRESTN, E-PRETN, E-RESTN, M-PRESTN, M-PRETN,
M-RESTN, M-ESTPR, M-ETPR, M-ESTR, M-NESTPR, M-NETPR, M-NESTR, M-NE12STPR,
M-NE12TPR, M-NE12STR
•
•
•
•
Pressure Modules, E-P/ M-P, Pressure Temp Module, E-PT/ M-PT
•
The Recorder Module, E-REC/M-REC and the built-in recorders in F-CMREC1 or F-CMCREC1
and U-CMREC1 or N-CMREC1
Cardiac Output Modules, E-COP, E-COPSv, M-COP and M-COPSv
NIBP Modules, M-NIBP and hemodynamic multiparameter modules w/ N measurement
Compact Airway Modules, E-CO, E-COV, E-COVX, E-CAiOVX, E-CAiOV, E-CAiO, M-C, M-CO,
M-COV, M-CAiO, M-CAiOV, M-CAiOVX, Single-width Airway Modules M-miniC, E-miniC
Downloading Monitor Software
The following instructions apply to downloading of new monitor software in case of upgrade or
service. Detailed instructions for downloading software are supplied with software PCMCIA cards.
NOTE: All user settings will be lost after downloading of new monitor software.
NOTE: During the downloading of software, the serial number of the monitor is written on the software
card. The software can then be downloaded again onto the same monitor, but not onto any other
monitor.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Make sure that the monitor is switched to standby.
Press and hold the service reset button on the rear panel for at least five seconds or until the
service reset indicator LED turns off.
Open the cover for card drive slots, if installed. Insert the software card into one of the card drive
slots and press the software card firmly in position.
Make sure that at least 30 seconds have passed since the service reset, then switch the monitor
on.
Wait for approximately 80 seconds. After the start-up screen appears, enter the Service View
and make sure that the information regarding monitor software has been updated. Memorize
the serial number of new software.
Remove the software card.
Replace the original device plate for monitor software by the new one supplied with the software
card.
Perform Factory Reset, see “Performing Factory Reset” . Make sure that the monitor functions
normally after the restart.
Set the time and date.
21
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
10. Set the monitor's network communication according to the network software in use, if
necessary. Enter the service menu: Monitor Setup -Install/Service (16-4-34) - Service
(26-23-8)- Frame - Network- Config and set
•
•
•
•
•
Network software S-CNET99 -> DRI Level = 1999
Network software S-CNET01 -> DRI Level = 2001
Network software S-CNET02 -> DRI Level = 2001 or 2002 (WLAN)
Network software L-NET03 -> DRI Level = 2003
Network software L-NET05 -> DRI Level = 2005
NOTE: The DRI level 1999 is not selectable in all monitor software versions.
NOTE: If the DRI level is changed, the monitor will restart automatically.
11. Fill out all necessary documentation regarding the new monitor software.
NOTE: The license agreement of monitor software needs to be in accordance with the monitor
software serial number. Make sure you archive the license agreement in a secure location.
NOTE: The first start-up after software loading takes considerably longer.
3.3.7
Performing Factory Reset
NOTE: The factory reset is necessary after replacing monitor software.
NOTE: The factory reset will restore all customized defaults, including language selection, to factory
defaults.
1.
2.
3.
4.
5.
3.3.8
Press the Monitor Setup key.
Select Install/Service and password (16-4-34).
Select Service and password (26-23-8).
Select Set/ Test and Factory Reset.
The monitor will perform an automatic restart. After the restart is completed, restart the monitor
also manually.
Installing the Datex-Ohmeda Network and MemCard Upgrade, U-CMMEM
The following instructions apply to upgrading the monitor with both the MemCard and the Network
options. Detailed upgrade instructions are supplied with the corresponding upgrade product.
NOTE: You can download the option software only onto one monitor. During the downloading of
option software, the serial number of the monitor is written on the software card, and if the
downloading for some reason would fail, the software can be downloaded again onto the same
monitor, but not onto any other monitor.
1.
2.
3.
4.
Make sure that the monitor is switched to standby.
Detach the cover plate on the network connectors at the rear of the frame unit (above the power
supply unit). Leave the collar on the connectors attached.
Open the cover for card drive slots (on the left side of the monitor). Insert the option software
card into one of the card drive slots and press the software card firmly in position.
Switch the monitor on.
22
Document no. M1031517-02
System installation
5.
Wait until the normal screen appears and check that a message 'Field upgrade OK' is displayed
as a note of successful upgrade.
6. Remove the option software card.
7. Enter the service menu and make sure that both options were loaded (Monitor Setup
-Install/Service - Service - Frame - Options - "Net+DC").
8. Install the device plate for option software on inside the cover for card drive slots. Close the
cover.
9. Test the monitor with a MemCard and by connecting it to Datex-Ohmeda Network.
10. Fill out all necessary documentation regarding the upgrade.
3.3.9
Installing the Datex-Ohmeda Network Upgrade, U-CMNET
The following instructions apply to upgrading the monitor with the Network option. Detailed upgrade
instructions are supplied with the corresponding upgrade product.
NOTE: You can download the option software only onto one monitor. During the downloading of
option software, the serial number of the monitor is written on the software card, and if the
downloading for some reason would fail, the software can be downloaded again onto the same
monitor, but not onto any other monitor.
1.
2.
Make sure that the monitor is switched to standby.
Detach the cover plate on the network connectors at the rear of the frame unit (above the power
supply unit). Leave the collar on the connectors attached.
3. Open the cover for card drive slots (on the left side of the monitor). Insert the option software
card into one of the card drive slots and press the software card firmly in position.
4. Switch the monitor on.
5. Wait until the normal screen appears and check that a message 'Field Upgrade OK' is
displayed as a note of successful upgrade.
6. Remove the option software card.
7. Enter the service menu and make sure that the option was loaded (Monitor Setup
-Install/Service - Service - Frame - Options - "Net").
8. Install the device plate for option software on inside the cover for card drive slots. Close the
cover.
9. Test the monitor by connecting it to Datex-Ohmeda Network.
10. Fill out all necessary documentation regarding the upgrade.
3.3.10 Installing the S/5 Wireless LAN Upgrade, U-CMW
The following instructions apply to upgrading the monitor with the Wireless LAN option. Detailed
upgrade instructions are supplied with the corresponding upgrade product.
You can download the option software only onto one monitor. During the downloading of option
software, the serial number of the monitor is written on the software card, and if the downloading for
some reason would fail, the software can be downloaded again onto the same monitor, but not onto
any other monitor.
1. Make sure that the monitor is switched to standby.
2. Open the cover for card drive slots (on the left side of the monitor). Insert the option software
card into one of the card drive slots and press the software card firmly in position.
3. Switch the monitor on.
23
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Wait until the normal screen appears and check that a message 'Field Upgrade OK' is
displayed as a note of successful upgrade.
Remove the option software card.
Switch the monitor to standby.
Detach the cover for card drive slots and install the antenna cover.
Insert the wireless LAN antenna card into the foremost card drive slot.
Switch the monitor on.
Enter the service menu and make sure that the option was downloaded successfully (Monitor
Setup - Install/Service - Service - Frame - Options - "WLAN" or "All").
Enter the WLAN service menu and enter appropriate Network ID, WEP Algorithm, Key ID and
Encryption Key information (Monitor Setup - Install/Service - Service - Frame - Network WLAN - WLAN Config).
Check all installed options on the monitor software device plate and attach the Virtual ID sticker
under the device plate at the monitor rear panel.
Test the monitor on Datex-Ohmeda Network.
Fill out all necessary documentation regarding the upgrade.
3.3.11 Installing the S/5 Recorder Upgrade, U-CMREC1
NOTE: Only S/5 Compact Anesthesia Monitor rev. 02 or later and S/5 Compact Critical Care Monitor
rev. 02 or later can be upgraded with this S/5 Recorder Upgrade kit.
1.
2.
3.
4.
5.
6.
7.
8.
Turn the monitor off.
Disconnect the power cord.
Push the Service Reset button for at least 5 seconds until the service reset indicator LED turns
off (the fan should turn off).
Remove the plate that covers the recorder installation place in the side panel.
Open the recorder (by pressing the button on the right upper corner at the front of the recorder).
Insert the recorder from outside to the side panel (opening button upwards).
Attach the recorder to the side panel with two screws at the back of the recorder (the screws can
be accessed inside the recorder).
Check that the recorder and the side panel are aligned and the recorder tightly attached.
Figure 7
9.
Installation of the U-CMREC1
Attach the device plate to the back cover of the monitor, near the other device plates.
24
Document no. M1031517-02
System installation
3.4
S/5 Remote Controller, K-CREMCO
To connect S/5 Remote Controller, K-CREMCO, to an S/5 Compact Monitor:
1. Make sure that the monitor is switched to standby.
2. Connect the K-CREMCO to the 5-pin DIN connector X9 that is located on the right side of the
Compact Monitor display unit.
3.5
Anesthesia Record Keeping Keyboard, K-ARKB
To connect Anesthesia Record Keeping Keyboard, K-ARKB, to an S/5 Compact Monitor:
1. Make sure that the monitor is switched to standby.
2. Connect the K-ARKB with an appropriate cable to the 5-pin DIN connector X9 that is located on
the right side of the Compact Monitor display unit.
3.6
ARK Barcode Reader, N-SCAN (optional)
3.6.1
Connection to Compact Monitor
1.
2.
Make sure that the monitor is switched to standby.
Connect the N-SCAN with an appropriate cable to the 5-pin DIN connector X9 that is located on
the right side of the Compact Monitor display unit.
Figure 8
ARK Barcode Reader, N-SCAN connected to Compact Monitor
25
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.7
S/5 Compact Airway Modules, E-xxxx / M-xxxxx
This chapter provides information for installing Compact Airway Modules E-xxxxx.
Figure 9
Compact Airway Module, E-XXXX
Connection to frame
1.
2.
3.
3.7.1
Ensure that the module is properly orientated (i.e. module release latch facing downward).
Align the module insertion guide slot with the insertion guide.
Push the module into the frame until it clicks.
Sample gas exhaust
Preventing operation room pollution
When N2O or volatile anesthetics are used, pollution of the operation room by these gases should be
prevented. Connect the sample gas outlet of the monitor to the scavenging system or return it to the
patient circuit.
NOTE: The sample gas from the E-miniC/ M-miniC can only be connected to the scavenging, not
returned to the patient circuit.
Connect the sample gas outlet of the monitor to the scavenging system either
•
•
CAUTION
through the ventilator, or
directly to the vacuum scavenging system.
Strong scavenging suction may change the operating pressure of the Airway Module
and cause inaccurate readings or internal damage. To prevent this, there must for
example be an opening to room air.
Connect the sample gas outlet only to an open scavenging system where gas is removed in room
pressure.
26
Document no. M1031517-02
System installation
Scavenging through the ventilator reservoir
SAMPLE GAS OUT
Figure 10
1.
2.
Scavenging through ventilator reservoir
Connect an exhaust line to the sample gas outlet on the module’s front panel.
Attach the other end of the line to the ventilator reservoir. Make sure that the reservoir tube
diameter is at least 2 - 3 times larger than the exhaust line.
Scavenging through the anesthesia gas scavenging system
Anesthesia machines are equipped with an anesthesia gas scavenging system (AGSS), and in some
machines the sample gas outlet can be connected directly to that.
For example, connect the sample gas outlet to the S/5 Avance:
Figure 11
Connecting the gas module to the scavenging connector of S/5 Avance
NOTE: Refer to the anesthesia machine’s documentation to find out where and how the sample gas
can be connected.
27
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Connecting directly to the vacuum scavenging system
1.
2.
Connect the exhaust line to the monitor’s sample gas outlet.
Connect the exhaust line only to an open scavenging system where gas is removed at room
pressure. Do not connect the monitor directly to a vacuum scavenging system.
Returning sampling gas to the patient circuit
The sampling gas can also be returned to the patient circuit. If you use the S/5 Anesthesia Delivery
Unit (ADU), you need an optional adapter connected to the patient breathing tubes.
Take special care when returning sample gas to the patient circuit. For further information, please
contact your GE Healthcare distributor.
NOTE: If E-miniC is being used, do not return the sample gas to the patient circuit.
SCAVENGING
SAMPLE GAS OUT
Figure 12
28
Document no. M1031517-02
Sample gas returned to patient circuit in ADU
System installation
3.7.2
Troubleshooting
If a problem occurs during a functional examination, check the components of the monitor according
to the following troubleshooting chart. If the problem persists, please refer to Part II of this Technical
Reference Manual.
Trouble
Treatment
Nothing functions.
Unplug and re-plug Remote Controller Cable. Also confirm that the cable is intact.
Unplug and re-plug the Power Cord. Also confirm that the cable is intact.
Confirm that the fuses are intact.
A plug-in module does not Remove and replace the module.
function.
Confirm that the desired parameters are configured to be displayed.
Compact Airway Module
does not function.
Confirm that ‘Occlusion’ or ‘Calibrating Gas Sensor’ messages are not displayed.
Confirm that a D-fend water trap and a sample tube are attached.
Confirm that the desired parameters are configured to be displayed.
Remove and replace the module.
29
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
For your notes:
30
Document no. M1031517-02
Interfacing
4
Interfacing
External devices can be interfaced with the S/5 Compact Anesthesia and S/5 Compact Critical Care
Monitors via the Compact Monitor’s serial port, via the Interface Module, E-INT / M-INT, and via the
Device Interfacing Solution, N-DISxxx.
The serial port can be used for interface with:
•
•
•
S/5 Anesthesia Delivery Unit
Printers
Computers
An E-INT / M-INT can be used for interface with:
•
•
•
Datex-Ohmeda monitors
Various other manufacturers’ monitors
Various anesthesia machines
Printers and computers can be interfaced via the monitor’s serial port.
Device specific N-DISxxx modules can be used with:
•
•
•
•
4.1
Ventilators/ anesthesia machines
Heart-lung machines
Monitors
Blood-gas analyzers
Interfacing external monitors via Interface Module, E-INT / M-INT
It is possible to interface Datex-Ohmeda monitors, Critikon Dinamap 1846SX, Abbott Oximetrix 3,
Baxter Explorer and Vigilance, Nellcor N-100, N-200 and N-1000 to the S/5 Compact Anesthesia
Monitor or to the S/5 Compact Critical Care Monitor via Interface Module, E-INT / M-INT. The
parameters that are transferred from external monitors are summarized in tables: Table 1
Transference of parameters, Datex-Ohmeda monitors and Table 2 Transference of parameters,
external monitors.
The Interface Module, E-INT / M-INT, has two serial/analog connectors (X7 and X8).
WARNING
Always make sure that the combination complies with the international safety
standard IEC 60601-1-1 for medical electrical systems and with the
requirements of local authorities.
31
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Table 1
Device
Waveforms (analog) Numerics
Alarms
Cardiocap
E-INT / M-INT -> CO2
Et&Fi Airway gases,
Respiration rate, SpO2,
Pulse rate
None
Capnomac
Capnomac II
E-INT / M-INT -> CO2,
Pleth
Et&Fi Airway gases,
Respiration rate
None
Capnomac Ultima
E-INT / M-INT -> CO2
Et&Fi Airway gases,
Respiration rate,
Spirometry, SpO2, Pulse
rate, Pleth amplitude
CO2, O2, Anesthesia
agent, Respiration rate,
Apnea, Occlusion, SpO2,
Pulse rate
Normocap 200
Normocap 200 OXY
E-INT / M-INT -> CO2
Et&Fi Airway gases,
Respiration rate
None
Oscar
Oscar II
Oscar OXY
E-INT / M-INT -> CO2,
Pleth
Et&Fi Airway gases,
Respiration rate, SpO2,
Pulse rate, Pleth
amplitude
None
Satlite
Satlite II
Satlite Plus
E-INT / M-INT -> CO2
SpO2, Pulse rate, Pleth
amplitude
None
Satlite Trans
None
SpO2, Pulse rate, Pleth
amplitude
None
Table 2
4.1.1
Transference of parameters, Datex-Ohmeda monitors
Transference of parameters, external monitors
Device
Waveforms
Numerics
Alarms
Critikon
Dinamap 1846SX
None
NIBP
None
Abbott
Oximetrix 3
None
SvO2/SaO2, CO
None
Baxter
Explorer
None
C.O., SvO2, REF, Tblood
None
Baxter
Vigilance
None
C.O., SvO2,C.C.O., Tblood
None
Nellcor
N-100
N-200
N-1000
Pleth (analog)
SpO2, Pulse rate
None
Connection to external Datex-Ohmeda monitors
Use the INT-External Device Cable.
1. Make sure that the power to both monitors is turned off.
2. Connect the 9 pin D-connector to one of the connectors on the Interface Module, E-INT / M-INT.
Tighten the finger screws.
3. Connect the 25 pin D-connector to the corresponding connector on the other monitor. Tighten
the finger screws.
32
Document no. M1031517-02
Interfacing
4.1.2
Connection to Critikon Dinamap 1846SX, Abbott Oximetrix 3 and Baxter Explorer
Use the INT-External Device Cable.
1. Make sure that the power to both monitors is turned off.
2. Connect the 9 pin D-connector to one of the connectors on the Interface Module, E-INT / M-INT.
Tighten the finger screws.
3. Connect the 25 pin D-connector to the connector on the external monitor. Tighten the finger
screws.
4.1.3
Connection to Baxter Vigilance
Use the INT-Baxter Vigilance Cable.
1. Make sure that the power to both monitors is turned off.
2. Connect the 9 pin D-connector to one of the connectors on the Interface Module, E-INT / M-INT.
Tighten the finger screws.
3. Connect the other 9 pin D-connector to a corresponding connector on the external monitor.
Tighten the finger screws.
Communication parameters are: baud rate 19200, no parity (none), data bits 8, stop bits 1. Mode of
communication port: IFM out.
4.1.4
Connection to Nellcor N-100 and N-1000
Use the Monitor-Nellcor Cable.
1. Make sure that the power to both monitors is turned off.
2. Connect the 9 pin D-connector to one of the connectors on the Interface Module, E-INT / M-INT.
Tighten the finger screws.
3. Connect the other connector to the corresponding connector on the external monitor.
Tighten the finger screws. Connect also the mono connectors on the external monitor.
4.1.5
Connection to Nellcor N-200
Use the Monitor-Nellcor Cable.
1. Make sure that the power to both monitors is turned off.
2. Connect one of the connectors to the corresponding connector on Interface Module, E-INT /
M-INT. Tighten the finger screws.
3. Connect the other connector to the corresponding connector on the external monitor. Tighten
the finger screws. Connect also the mono connectors on the external monitor.
Connect also the mono connectors on the external monitor.
33
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.2
Interfacing external bedside devices via S/5 Device Interfacing
Solutions, N-DISxxx
The Device Interfacing Solution, N-DISxxx provides means for transferring physiological, waveform
and event data from various bedside patient care devices to the Datex-Ohmeda monitoring system.
The real-time and trended data can be displayed on the monitor screen and used for record keeping
purposes. The interfacing module reads the data coming from the external device, converts it to a
suitable format and sends it to the monitor.
See the following table of DIS modules and devices that you can interface with the Device Interfacing
Solution.
NOTE: The Device Interfacing Solution (DIS) is only compatible with the S/5 Compact Anesthesia and
S/5 Compact Critical Care Monitor when the monitor has S/5 Monitor software of rev. 02 or later
installed.
Table 3
DIS modules and interfaced devices
Device Ventilators
N-DISEV4
Evita 4a
N-DISPRIM
Primusa.
N-DIS7200
7200 Series Ventilator Systemb
N-DIS840
840 Ventilator Systemb.
N-DISS300
Servo Ventilator 300c
N-DIS7900
7900 SmartVent Ventilatord
N-DISAEST e
Aestiva/5d.
N-DISVENT
S/5 Aespired.
NOTE: Not available in the US
Aestiva/5d.
Aisys Carestationd.
S/5 Avanced.
Centiva/5d.
Engström Carestationd.
a.
b.
c.
d.
e.
Trademark of Dräger Medical AG & Co
Trademark of Nellcor Puritan Bennet Inc
Trademark of Maquet Critical Care AB part of the Getinge Group (previously trademark of Siemens)
Trademark of GE Healthcare Finland Oy
Replaced by N-DISVENT
Device Monitors
N-DISOXIM3
Oximetrix 3a
N-DISQVUE
QVue /Q2a.
N-DISA2000
A-2000 Bispectral Index Monitoring Systemb
N-DISVIGIL
Baxter-Vigilancec
N-DISPICCO
PiCCO-Technologyd
34
Document no. M1031517-02
NOTE: Not available in the US
Interfacing
N-DISRGM
RGM Monitore
N-DISTONO
Tonocape.
N-DISWHITE
Capnomac, Capnomac IIe.
Multicap, Normocap, CD2-O2e.
Capnomac Ultimae.
Normocap CD-200e.
Oscar Oxy, Cardiocap 1GS, Cardiocap 2GSe.
Satlite, Satlite Trans, Satlite Pluse.
a.
b.
c.
d.
e.
Trademark of Hospira Inc. (previously trademark of Abbott Laboratories)
Trademark of Aspect Medical Systems
Trademark of Edwards Lifesciences Corporation
Trademark of Pulsion Medical Systems
Trademark of GE Healthcare Finland Oy
Device Blood gas analyzers
N-DISOPT
AVL Opti CCAa
Device Heart-lung machines
N-DISHL20
Jostra HL-20b
a. Trademark of Diamond Diagnostics Inc
b. Trademark of MAQUET GmbH & Co. KG part of the Getinge Group
For specific information on parameters transferred from the interfaced device to the Datex-Ohmeda
monitor and the applicable software versions of the device refer to the Installation guide
accompanying each DIS module.
4.2.1
Device Interfacing Solution components
The Device Interfacing Solution consists of:
−
a device specific interfacing module
−
a device specific cable
−
a bus cable
−
a connector for another bus cable
−
label specifying the external device
4.2.2
Connections
Connect the device specific cable to the external device and the bus cable to the monitor's DIS
connector or to another interfacing module.
35
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
(1)
(2)
(3)
(4)
(5)
Figure 13
label specifying the external device
LED indicators
black bus cable from another interfacing
module, if needed
grey device specific cable to the
communication port of the external
device
black bus cable to the monitor’s DIS
connector (or to another interfacing
module)
Connection cables and LED indicators
WARNING
The Compact Monitor, interfacing modules and interfaced devices must be
situated in the same patient environment (as defined in IEC 60601-1-1).
WARNING
Connecting electrical equipment together or using the same extension cord for
more than one device may cause their leakage currents to exceed the limits
specified in relevant safety standards. Always make sure that the combination
complies with the international safety standard IEC 60601-1-1 for medical
electrical systems and with the requirements of local authorities.
WARNING
The manufacturer guarantees a reliable functioning of the devices with tested
software versions only. Always refer to the Installation guide accompanying the
DIS module and verify the compatibility before use.
4.2.3
Mounting
The DIS module can be mounted on the side panel of the external device. Also IV pole placement is
possible.
NOTE: As the Device Interfacing Solution works only with the device specified in the label of the
interfacing module, it is recommended that the interfacing module always travels along with the
external device.
36
Document no. M1031517-02
Interfacing
For mounting accessories, please refer to the “Supplies and Accessories” catalog. See the figure
below for an example of a device interfacing.
1
4
Figure 14
(1)
(2)
(3)
(4)
An example of interfacing external devices with Device Interfacing Solution
Datex-Ohmeda S/5 Compact Anesthesia Monitor (with software L-CANE02(A) or later)
Aestiva/5 anesthesia machine
RGM monitor
Interfacing module
NOTE: You can connect up to ten (10) interfacing modules to one system simultaneously.
Check the maximum number of modules: one meter cable = max. four ten modules, three meter
cable = max. three modules, six meter cable = one module.
CAUTION
Make sure that the interfacing module is always used in vertical position to prevent
water from entering the module.
CAUTION
Make sure that you are connecting the interfacing module to the device specified in
the label.
4.2.4
Selecting the external device
1.
2.
3.
4.
Turn off the external device.
Connect the interfacing module to the monitor’s connector for S/5 DIS or to another interfacing
module.
Connect the device specific cable to the external device and turn the external device on.
The monitor identifies the connected device automatically.
37
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.2.5
Functional check
There are two ways to check the function of the S/5 Device Interfacing Solution:
1.
2.
Press the Monitor Setup key.
Select Interfacing and open the Status Page menu. The status page shows you the current
communication status of the interfacing module (1 - 10).
NOTE: The status message ‘Connected’ appears on the Status Page after you have connected the
external device to the interfacing module and turned it on. Note also that the monitor and the
interfacing module must be operational.
•
Check the LED indicators on the interfacing module (the green LED indicates physical
connections, the yellow LED software selections)
:
4.2.6
GREEN
YELLOW
INDICATION
lit
dark
Physical connections between the monitor, interfacing module
and external device are in order and the device has been
selected in the menu.
dark
lit
There is something wrong with the physical connections
between the monitor, interfacing module and external device.
The external device has not been selected in the menu.
lit
lit
Physical connections between the monitor, interfacing module
and external device are in order but the external device has not
been selected in the menu.
dark
dark
The interfacing module is not connected to the monitor.
Selecting the parameter data source
Select the external device via Monitor Setup - Interfacing menu:
•
•
Select the desired parameter, for example Gases.
Select the desired source by name, for example Aestiva.
NOTE: The name of the device is visible on the list only if the device is correctly connected.
NOTE: Detailed information about interfacing module related mountings, connections and settings is
included in the installation guides that are delivered with the interfacing modules.
38
Document no. M1031517-02
Interfacing
4.3
Interfacing Datex-Ohmeda Anesthesia Delivery Unit
It is possible to interface the Datex-Ohmeda Anesthesia Delivery Unit to the S/5 Compact Anesthesia
Monitor via the serial interface port. The data link is bi-directional. The parameters transferred to the
Anesthesia Delivery Unit are summarized in Table 4 and the events transferred to the S/5 Compact
Anesthesia Monitor are summarized in Table 5. The events are transferred continuously once a
minute or during the system check procedure and appear in the trend pages or in the anesthesia
record. The transfer of events requires record-keeping software.
4.3.1
Interconnection
Use the ADU-AS/3 Monitor Cable.
4.3.2
4.3.3
Setting interfacing parameters on the S/5 Anesthesia Delivery Unit
1.
2.
3.
Press the Setup key.
Select Install password 10.
Select Interfacing and choose S/5 AM.
4.
Press the Normal Screen key.
Setting interfacing parameters on the S/5 Compact Anesthesia Monitor
No settings are required on the S/5 Compact Anesthesia Monitor.
Table 4
Parameters transferred from S/5 Compact Anesthesia Monitor to S/5 Anesthesia
Delivery Unit
Waveforms
Numerics
CO2
Et & Fi CO2 %
Et & Fi O2 %
O2% difference (I-E)
Et & Fi N2O%
Et & Fi AA%
Vol Exp MV
Vol Exp TV
39
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Table 5
Events transferred from S/5 Anesthesia Delivery Unit to the S/5 Compact
Anesthesia Monitor
Events transferred once a minute
Ventilator settings
Ventilation (mode)
Tidal Volume
Minute Volume
Resp. Rate
I:E Times: inp
I:E Times: exp
InspPause
Ventilator measurements
Ppeak
Pplat
Peep
Pmin
Fresh gas settings
Agent name
Agent % in fresh gas
Total flow
O2 flow
N2O flow
Air flow
Events transferred during system check
System check test results
4.4
Gas Delivery: Agent
Gas Delivery: N2O
Leak Tests: AUTO
AUTO Leak (ml/min)
Leak Test: MAN
MAN Leak (ml/min)
Number of confirmed checklist items
Bypass Check
Interfacing Dräger Cicero, Cato, Julian and Narkomed 2C (by NAD)
It is possible to interface Dräger Cicero and Cato to the S/5 Compact Anesthesia Monitor or to the
S/5 Compact Critical Care Monitor via the Interface Module, E-INT / M-INT.
The parameters transferred to the S/5 Compact Anesthesia Monitor or S/5 Compact Critical Care
Monitor are summarized in Table 6 and Table 7.
NOTE: Some of the summarized parameters (waveforms or numerics) may not be available in all
device versions.
WARNING
Always make sure that the combination complies with the international safety
standard IEC 60601-1-1 for medical electrical systems and with the
requirements of local authorities.
40
Document no. M1031517-02
Interfacing
4.4.1
Interconnection
Use the INT-External Device Cable, except for Julian and Cicero EM, in which case use the
INT-Julian/Cicero EM cable.
1. Make sure that the power to both monitors is turned off.
2. Connect the 9 pin D-connector to one of the connectors on the Interface Module, E-INT / M-INT.
Tighten the finger screws.
3. Connect the 25 pin D-connector to a corresponding connector on the anesthesia machine. The
connector is labeled 'RS-232-C'. Tighten the finger screws.
4.4.2
Setting communication parameters
Set the communication parameters for Cicero and Cato to RS-232: 9600, e, 8, 1 (MEDIBUS 3.00). In
all cases please refer to the documentation provided by Dräger.
4.4.3
Setting interfacing parameters on the S/5 Compact Anesthesia or Compact Critical
Care Monitor
1.
2.
3.
4.
Press the Monitor Setup key.
Select Install/Service (password 16-4-34).
Select Service (password 26-23-8) - Parameters - More...
Select Interface and combine a required parameter with the external monitor. Two letters, al,
denote alarm integration. The selection will be automatically stored in permanent memory.
5.
Press the Normal Screen key.
Table 6
Parameters transferred from Dräger Cicero monitor to S/5 Compact Anesthesia
Monitor or S/5 Compact Critical Care Monitor
Selection
Waveforms
Numerics
States
Gases / SSS
CO2 (kPa, mmHg, %)
CO2 Fi & Et (kPa, %)
O2 Fi & Et (%)
N2O Fi & Et (%)
RR (CO2) (1/min)
AA Fi & Et (%)
Tidal Volume insp. (1)
Minute Volume exp. (1)
Ppeak (mbar)
Pplat (mbar), PEEP (mbar)
None
SpO2
Pleth (% full scale)
SpO2 (%)
Pulse rate (1/min)
Probe Off
41
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Table 7
Parameters transferred from Dräger Cato, Julian and Narkomed 2C (NAD) monitor
to the S/5 Compact Anesthesia Monitor or S/5 Compact Critical Care Monitor
Selection
Waveforms
Numerics
States
Gases / SSS
CO2 (kPa, mmHg, %)
CO2 Fi & Et (kPa, %)
O2 Fi & Et(%)
N2O Fi & Et (%)
RR (CO2) (1/min)
AA Fi & Et (%)
Tidal Volume insp. (1)
Minute Volume exp. (1)
Ppeak (mbar)
Pplat (mbar); not in Narkomed 2C
PEEP (mbar)
None
SpO2
Pleth (% full scale)
SpO2 (%)
Pulse rate (1/min)
Probe Off
NOTE: The transference of parameters illustrated in Table 4 and Table 5 represents the maximum.
Some of these parameters may not be available in all device versions.
NOTE: The transference of waveforms requires the MEDIBUS real-time extension and, in Cato
monitors, waveforms are available only on port 1.
4.5
Interfacing printer
It is possible to interface a laser printer (serial or parallel) with the S/5 Compact Monitors via the
monitors’ serial port. The printer should be PCL5 compatible and should contain at least 2 MB of
memory. Parallel printers require the use of Serial-to-Parallel Converter, order code 78030, model
PI 130-R2 or PI 1115A.
WARNING
Always make sure that the combination complies with the international safety
standard IEC 60601-1-1 for medical electrical systems and with the
requirements of local authorities.
WARNING
Connecting the power supply cord of the printer to the wall power outlet may
cause the printer leakage current to exceed the limit specified for medical
equipment. A printer must be supplied from an additional transformer providing
at least basic isolation (isolating or separating transformer).
4.5.1
4.5.2
Setting S/5 Compact Monitor interface for printers
1.
2.
3.
Press the Print/Record key.
Select Printer Connection.
Select Serial.
4.
Press the Normal Screen key.
Connection to serial printers
A serial printer is connected to the serial port connector X11 on the frame unit.
Contact your authorized GE Healthcare distributor for advice on suitable serial printers.
42
Document no. M1031517-02
Interfacing
4.5.3
Connection to parallel printers
A parallel printer is connected to the serial interface port connector X11 on the frame unit via the
Serial-to-Parallel Converter, order code 78030, model PI130-R2 or PI1115A.
Contact your authorized GE Healthcare distributor for advice on suitable parallel printers.
4.5.4
Installing the Serial-to-Parallel Converter
Order code 78030, model PI130-R2
A common serial modem cable, gender changer and parallel printer cable are required when
connecting the serial to parallel converter between the monitor and a parallel printer. The converter
gets power from the connected devices.
1. Make sure that power is switched off on both devices.
2. Connect a standard PC-to-parallel-printer cable (order code 713701) to the parallel printer.
3. Check the DIP-switch settings on the converter (order code 78030, model PI130-R2):
Position
1
Flow Control:
hardware
LED: Enabled
2
3
4
5
8
OFF OFF OFF
D.Rate (kbps):
115,2
OFF ON OFF
Connect a DB25 female-to-female gender changer (order code 78032) between the printer
cable and converter.
DB9F plugs
into CM1
1
Standard Async Modem Cable
Figure 15
5.
7
ON
Parity/D, Bits/S, Bit:
None/8/1
4.
6
OFF
Gender changer
plugs into
converter
2
Serial to Parallel
Converter
3
DB25M end
plugs into gender
changer
DB25F/DB25F
Gender Changer
4
Centronics
end plugs
into printer
Standard Parallel Printer
Adapter Cable
Parallel printer
Connecting S/5 Compact Monitor to printer, converter model PI130-R2
Connect a common RS-232 modem cable’s (order code 78031) DB9 connector to the serial
port connector X4 on the monitor, and the DB25 connector to the converter.
Order code 78030, model PI1115A
A common serial modem cable, power adapter and parallel printer cable are required when
connecting the serial to parallel converter between the monitor and a parallel printer. The converter
gets power from an external power supply and requires an external power adapter.
NOTE: The order code 78030 includes the new serial to parallel converter PI1115A and the European
power adapter PS1002-EU (230 VAC/50 Hz). Power adapters for US, UK or Asian markets must be
locally sourced from Black Box Corporation through its international distributor network, see
http://www.blackbox.com - Contact us - Contacts by Country.
43
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
To connect the S/5 Compact Monitor to printer:
1. Make sure that power is switched off on both devices.
2. Connect a standard PC-to-parallel-printer cable (order code 713701) to the parallel printer.
3. Check the DIP-switch settings on the converter (order code 78030, model PI1115A).
Setting
Position
115.2K Baud
1
2
3
ON
ON
ON
4
XON/XOFF
5
6
7
8
OFF
8 Data bits
OFF
No parity
OFF
Even parity
OFF
Serial to Par.
5.
Connect a common RS-232 modem cable’s (order code 78031) DB9 connector to the serial
port connector X4 on the monitor, and the DB25 connector to the converter.
Connect the converter to external power supply using the power adapter PS1002-xx.
DB9F plugs
into CM1
Standard Async Modem Cable
Serial to Parallel
Converter
Standard Parallel Printer
Adapter Cable
p/n 78030 (PI1115A)
p/n 78031
Figure 16
PS1002-EU, Power Adapter, 230 VAC Europe,
for PI1115A (included in p/n 78030),
plugs to power supply
Centronics
end plugs
into printer
Parallel printer
p/n 713701
Connecting S/5 Compact Monitor to printer, converter model PI 1115A
4.5.5 Connection to printer
Setting the printing parameters
Refer to the documentation provided with the printer.
4.6
Interfacing computer
A computer is connected to the serial port connector X11 on the frame unit. Contact your authorized
GE Healthcare distributor for further advice on computer interface.
WARNING
WARNING
Always make sure that the combination complies with the international safety
standard IEC 60601-1-1 for medical electrical systems and with the
requirements of local authorities.
Connecting the power supply cord of the computer to the wall power outlet may
cause the computer leakage current to exceed the limit specified for medical
equipment. A computer must be supplied from an additional transformer
providing at least basic isolation (isolating or separating transformer).
44
Document no. M1031517-02
cam p1 inst serial parallel conv p1115A a
4.
OFF
Interfacing
4.7
Output signals
Analog/ digital output signals on the connectors X4 and X8 can be used for interfacing with other
devices. The pin assignments are illustrated in tables/pictures below.
Table 8
Coding element connector, X4
9 pin female D-connector
5
1
9
6
Table 9
Signal
1
2
3
4
5
6
7
8
9
IDCS1 (chip select)
IDCL (clock)
IDDI (data in)
IDDO (data out)
IDPE (protect enable)
+5Vdc
Direct ECG
Nurse call
GND
Synchronization connector, X8
4 pin female connector
4.7.1
Pin
Pin
Signal
1
2
3
4
GND
Def_Sync
Direct ECG
Pressure Out
Digital outputs
The digital output signals are as follows:
Defibrillation Sync (X8 pin 2)
The defibrillation sync signal is generated by the ECG. When activated, the signal is set to a high level
and then set back to a low level after 10 ms. The signal is regenerated only after returning to the low
level. The high level ranges from 2.8 to 5 V, while the low level ranges from 0 to 0.8 V. The delay from
the R wave peak to the start of the signal is 35 ms maximum.
Nurse Call(X4 pin 8)
The Nurse Call signal is generated by red and yellow alarms. When activated, the signal is set to the
high state and remains at the high state until the alarm situation is over or the SILENCE ALARM key is
pressed. The high state range is from 2.8 to 5 V, while the low state range is from 0 to 0.8 V.
45
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.7.2
Analog outputs
Direct ECG (X4 pin 7 and X8 pin 3)
Delay (max.):
Gain ECG (out)/ECG (in):
Pacer:
15 ms
1 V/1 mV
5 V and 2 ms pulse
The signal requires input impedance of 100 kΩ.
NOTE: The ECG signal is based on the ECG measurement of the Hemodynamic Modules, M-ESTPR (all
variations), M-NES(12)TPR (all variations), E-PRESTN/ M-PRESTN (all variations). The ECG signal from
the modules is channel 1 (ECG1). The channels 2 and 3 (ECG2, ECG3) are not transmitted. Make sure
that the signal in channel 1 (ECG1) is good enough (extensive QRS for IABP synchronization). For
further information, please contact your authorized GE Healthcare distributor.
Pressure out (X8 pin 4)
−
P1 from Hemodynamic Module
NOTE: With monitor software version 03 or earlier, the Invasive pressure output signal is 1 V/100
mmHg, originally ranging from 0 to 300 mmHgand with a delay of approximately 25ms. The signal
requires an input impedance of 100k.
4.7.3
S/5 Pressure Temp Module, E-PT or M-PT, output signals
The signal output connector on the Pressure Temp Module, E-PT or M-PT, can be used to interface
some models of IABPs to the S/5 Compact Anesthesia Monitor and S/5 Compact Critical Care
Monitor. The pin assignments are illustrated in Table 10. Please contact your local distributor for more
information.
WARNING
Always make sure that the combination complies with the international safety
standard IEC 60601-1-1 for medical electrical systems and with the
requirements of local authorities.
Table 10
Signal output connector pin assignments
Pin
Signal
1
2
3
4
ECG out, ECG1
Pressure out, P3
ECG out, ECG1
Ground
Output signals
ECG out, ECG1
Pressure out, P3
ECG out, ECG1
46
Document no. M1031517-02
1V / 1mV
1V / 100mmHg
1V / 1mV
Functional check
5
Functional check
These instructions include procedures for a functional check for Datex-Ohmeda S/5 Compact
Anesthesia Monitor and S/5 Compact Critical Care Monitor. The functional check is recommended to
be performed after monitor installation.
These instructions include a “Functional check form, Datex-Ohmeda S/5 CAM, CCCM” to be filled in
when performing the procedures. The symbol
" in the instructions means that the performed
procedure should be signed in the check form. The procedures should be performed in ascending
order, bypassing those that are not applicable for a particular monitor.
All menu selections related to Datex-Ohmeda products are written in following typeface:
e.g. Parameters - Gas Unit.
As you enter the service menus, you need the following passwords:
Monitor Setup - Install/Service (password 16-4-34) - Service (password 26-23-8)
In case you evaluate the measurement accuracy with a patient simulator, add simulator’s accuracy
specification to the one of the monitor.
An electrical safety check and a leakage current test are recommended to be performed prior to the
monitor installation.
5.1
Recommended tools
For product(s)
Tool
Order No.
Airway modules
Compact Airway Module, E-CAiO(VX)/ Calibration gas and regulator
M-CAiO(VX)
755583/755534*
Compact Airway Module, E-COVX/
M-COVX
Calibration gas and regulator
755587/755534*
Compact Airway Module, E-CO(V),
M-C, M-CO(V)
Calibration gas and regulator
755581/755534*
E-miniC/ M-miniC
Calibration gas and regulator
755580/755534*
Compact Airway Module, E-COVX,
E-CAiOVX, M-COVX, M-CAiOVX
Sampling line, 2 m
73318
All Airway modules w/ (V)
Spirometry tube, 2 m
890031
D-lite
733950
Hemodynamic modules w/ (P),
M-NIBP
NIBP cuff and hose
2753E (cuff)
877235 (hose)
Hemodynamic modules w/ (P)
InvBP transducer
70077-001
Hemodynamic modules
47
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
For product(s)
Tool
Order No.
Multi-Link ECG accessories, IEC
E-PSM(P)/ E-PRESTN/ M-PRESTN
-
Multi-link 3-leadwire set
412682-003
-
Multi-link 5-leadwire set
412681-003
-
Multi-link 5-leadwire set, C2-C6
416467-004
E-PRESTN/ M-PRESTN w/ (E12)
-
Multi-link 12-lead ECG trunk cable 416035-002
or
Multi-Link ECG accessories, AHA
E-PSM(P)/ E-PRESTN/ M-PRESTN
-
Multi-link 3-leadwire set
412682-001
-
Multi-link 5-leadwire set
4162681-001
-
Multi-link 5-leadwire set, V2-V6
416467-003
E-PRESTN/ M-PRESTN w/ (E12)
-
Multi-link 12-lead ECG trunk cable 416035-001
M-NESTPR
3-lead ECG trunk cable
545302
5-lead ECG cable
545303
M-NESTPR w/ (E12)
10-leadwire ECG cable
545324
E-PSM(P)/ E-PRESTN
SpO2 finger probe
OXY-F-UN
SpO2 Interconnect Cable
OXY-ES3
M-PRESTN
SpO2 finger probe
OXY-F4-N or SAS-F4
E-NSAT/ M-NSAT
Nellcor SpO2 probe
Hemodynamic modules w/ (T)
Temperature test set
884515
Hemodynamic E-Modules w/ (NIBP)
Adult NIBP cuff hose with cuff ID
2021285-001
Infant cuff hose without cuff ID
414874-001
Hemodynamic M-Modules w/ (NIBP) Adult NIBP cuff
Adult NIBP cuff hose
572435
877235
E-COP/ E-COPSv/ M-COP/ M-COPSv C.O. Catheter cable
16590
E-COPSv/ M-COPSv
890121
SvO2 simulator
Tonometry Module, E-TONO/ M-TONO Calibration gas and regulator
755580/755534*
Sampling line
733251
TonometricsTM catheter
TONO-14F or another suitable
TONO-_F catheter
Luer plug
Pressure manometer
EEG Module, E-EEG/ M-EEG
Earphones
EEG simulator
48
Document no. M1031517-02
90502
Functional check
For product(s)
Tool
Order No.
BIS Module, E-BIS/ M-BIS
BIS simulator or
BIS Sensor simulator
900509
900508
E-ENTROPY/ M-ENTROPY
Entropy simulator
N-ES
Entropy sensor cable
8002964
NMT simulator
871251
M-NMT ElectroSensor
888416
M-NMT sensor cable
888415
MemCard – Data or Menu
893860 (Menu, English)
887045 (Data, English)
E-NMT/ M-NMT
MemCard option
NOTE: * Ensure that the calibration gas and regulator are functioning properly before calibration.
Perform annual maintenance on the regulator as required. For more information see section
“Adjustments and calibrations” in Compact Airway modules slot.
For details on recommended accessories see “Supplies and Accessories” catalog.
5.1.1
Hemodynamic patient simulators
The following tables present the patient simulators’ compatibility with each hemodynamic module, and the
accessories needed:
Table 11
Patient simulators’ compatibility with each hemodynamic module
Patient simulator
Module
Parameter
M1010831
MedSim
874027
E-PSM(P), E-PRESTN
ECG
Ok
Multilink ECG acc.
Not compatible
T
402015-004
402015-004 and
M1010832
InvBP
Ok
M1010858
ECG
Ok
Multilink ECG acc.
Not compatible
T
Ok
M1010832
M1010832
InvBP
Not compatible
Ok
Ok
ECG
M-PRESTN
Auto
On/Off
Start
Cancel
Zero
P1
SpO2
NIBP
Zero
P2
ECG
T1
P1
T2
P2
49
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Patient simulator
Module
Parameter
M1010831
MedSim
874027
M-NESTPR
ECG
Not compatible
300 series acc.
Ok
NIBP
T1
ECG+
Resp
T2
12 lead ECG Not compatible
300 series acc.
Not compatible
P1
T
Ok
M1010832
M1010832
P2
InvBP
Not compatible
Ok
Ok
SpO
2
Table 12
Adapter cables for hemodynamic patient simulators
Patient simulator
Adapter cables for simulators
Hemodynamic patient simulator
-
Dual temperature adapter cable
402015-004
Hemodynamic patient simulator
-
Dual Inv.BP adapter cable
2005772-001
Medsim
-
Temperature adapter cable
M1010832
Medsim
-
Inv.BP adapter cable
M1010858
Lionheart & MPS450
-
Temperature adapter cable
M1010846
Lionheart & MPS450
-
Inv.BP adapter cable
M1010862
5.2
Visual inspection
•
1.
Make sure that the monitor is switched to standby.
Disconnect the mains power cord from the monitor.
If the monitor is connected to the Datex-Ohmeda Network, disconnect the Mon-Net cable from
the monitor. Remove any memory cards, if installed.
Check all units visually
Check that all parts are intact and that the cables and screws are connected and tightened
properly. Especially check the following parts:
−
the display unit locking screw is in a locking position.
−
sampling line is connected to the Airway Module, if installed.
Check that modules go in smoothly and lock up properly.
"
50
Document no. M1031517-02
Functional check
5.3
Functional inspection
5.3.1
General
1.
2.
3.
4.
Connect the mains power cord.
Check that the LED above the main switch is lit continuously (full charged batteries) or
periodically (charging batteries).
Switch the monitor on.
Check that the monitor starts up properly, i.e. a normal start-up sound is heard from the
loudspeaker, the alarm LEDs turn on and off, and the monitoring screen appears.
No error messages should appear on the screen.
Configure the screen for the parameters that are connected.
Enter the Service Menu.
When applicable, check from the corresponding Parameters submenu that the Timeouts, Bad
checksums and Bad c-s by mod values of inserted modules are not increasing faster than by 5
per second. Check also that the module memories have passed the internal memory test, i.e.
RAM, ROM and EEPROM all state OK.
If installed, the recorder should record two lines of start-up information.
"
Preset the measurement settings for those parameters that are connected, for example:
Recorder - Record Waveforms - Waveform 1 - ECG1
- Waveform 2 - P1
- Waveform 3 - P2
Invasive Pressures - P1 ‘ART’ Setup -- Label – ART
- P2 ‘CVP’ Setup -- Label – CVP
- P3 Setup -Label –PA
- P4 Setup -Label -P4
- P5 Setup -Label -P5
- P6 Setup -Label -P6
Pulse Oximetry -Pleth Scale –AUTO
or
Others -SPO2 Setup - Pleth Scale –AUTO
Airway Gas -Spirometry View -Scaling -Indep.
-Paw Scale –20
-Flow Scale –15
or
Ventil.-Spirometry Setup -Scaling -Indep.
-Paw Scale –20
-Flow Scale –15
Others -Resp Setup -Size -1.0
- Resp Rate Source – AUTO
- Measurement – ON
- Detection Limit – AUTO
51
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
5.3.2
Display
1.
Check that the picture on the screen is correct.
"
5.3.3
Keyboard(s)
1.
Tests with all the connected keyboards:
−
Press the Monitor Setup key. Turn the ComWheel in both directions and check that the
cursor in the menu moves correspondingly. Select Normal Screen and check that the
menu disappears from the screen.
Tests with the Command Board:
−
Press the Help key. Turn the ComWheel in both directions and check that the cursor in the
menu moves correspondingly. Select Normal Screen and check that the menu
disappears from the screen.
Check the rest of the menu keys by pressing them one by one.
Tests with the ARK Keyboard:
−
Enter the Keyboard service menu
−
Check functioning of the ComWheel.
−
Press all keys, except Modify and Print. Check that each key produces a sound from the
loudspeaker, or the Message count value in the service menu increases.
−
Press the Modify and Print keys and check that the corresponding menus appear on the
monitor screen.
Tests with the Remote Controller:
−
Enter the Keyboard service menu.
−
Check the function of the ComWheel.
−
Press all keys. Check that each key produces a sound from the loudspeaker, or the
Message count value in the service menu increases.
"
5.3.4
Frame unit
1.
Check that the frame fan is running.
"
5.3.5
Display unit
2.
Check that the clock on the screen shows correct time. Readjust the time and date, if necessary.
"
52
Document no. M1031517-02
Functional check
5.3.6
Compact Airway Module, E-CXXXXX/ M-CXXXXX
1.
2.
Wait until the message ‘Calibrating gas sensor’ disappears from the screen.
Check that the fan is running.
If the module contains membrane keys on the front panel, press each of the keys for at least
one second and check that they are identified.
"
Compact Airway Modules with the Patient Spirometry option
3.
Connect a clean spirometry tube and D-lite to the module. Connect the sampling line.
Breathe through the wider side of the D-lite.
Check that the flow waveform moves downwards when you breathe in and upwards when you
breathe out.
"
For all Compact Airway Modules
4.
5.
6.
Block the tip of the sampling line with your finger and check that the message ‘Sample line
blocked’ appears on the monitor screen within 30 seconds.
Detach the D-fend and check that the message ‘Check D-fend’ appears on the monitor screen
within 30 seconds.
Breathe to the sampling line briefly. Check that the CO2 information is updated on the screen.
"
5.3.7
Single width Airway Module, E-miniC/ M-miniC
Wait until the message ‘Calibrating gas sensor’ disappears from the screen.
1.
2.
Block the tip of the sampling line with your finger and check that the message ‘Sample line
blocked’ appears on the monitor screen within 30 seconds.
Detach the Mini D-fend and check that the message ‘Check D-fend’ appears on the monitor
screen within 30 seconds.
Breathe to the sampling line briefly. Check that the CO2 information is updated on the screen.
"
5.3.8
Tonometry Module, E-TONO/ M-TONO
1.
Press each of the front panel membrane keys for at least one second and check that they are
identified.
"
53
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
5.3.9
Multiparameter Hemodynamic Modules
ECG and RESP measurements
1.
2.
Check the function of the front panel membrane key ECG, Lead, if available.
Connect an ECG cable to the module. Connect the cable leads to a patient simulator. Check
that all ECG and impedance respiration information is shown on the monitor screen as
configured on the simulator.
Turn the simulator off. Check that the ‘Asystole’ and ‘Apnea’ messages are displayed.
"
Temperature measurement
3.
Check the temperature channels with a patient simulator.
Check that temperature measurement information is shown on the monitor screen as
configured on the simulator.
"
Invasive blood pressure measurement
4.
5.
6.
Check the function of the front panel membrane keys.
Check the InvBP channels with a patient simulator.
Zero the InvBP channels and check that the values and waveforms correspond to the simulator
settings.
"
SpO2 measurement
7.
8.
Connect an SpO2 finger probe to the module. Check that the message ‘Probe off’ is shown when
the probe is not connected to a finger.
Attach the SpO2 probe to your finger. Check that a reading of 95-99 and a pleth waveform
appear on the screen
"
Non invasive blood pressure measurement
9. Check the function of the front panel membrane keys.
10. Attach an adult NIBP cuff onto your arm and perform one NIBP measurement. Check that the
module identifies the cuff, i.e. the text ‘Adult’ appears in the NIBP digit field for a short time.
Check that the module gives a reasonable measured result.
"
5.3.10 Pressure/Pressure Temp Modules, E-P, E-PT, M-P, M-PT
Invasive blood pressure measurement
1.
Check the function of the front panel Zero P3 key.
54
Document no. M1031517-02
Functional check
2.
Check the InvBP channel with a patient simulator.
Zero the InvBP channel. Then check that the values and waveforms correspond to the simulator
settings.
"
Temperature measurement
3.
Check the temperature channels with a patient simulator.
Check that the temperature measurement information is shown on the monitor screen as
configured on the simulator.
"
5.3.11 Dual pressure Module, E-PP/ M-PP
1.
2.
Check the function of the front panel Zero P5 and Zero P6 keys.
Check the InvBP channels with a patient simulator.
Zero the InvBP channels. Then check that the values and waveforms correspond to the
simulator settings.
"
5.3.12 Cardiac Output Modules, E-COP/ M-COP, E-COPSv/ M-COPSv
Invasive blood pressure measurement
1.
2.
Check the function of the front panel Zero P4 key.
Check the InvBP channel with a patient simulator.
Zero the InvBP channel. Then check that the values and waveforms correspond to the simulator
settings.
"
Cardiac Output measurement
3.
Check the function of the front panel Start C.O. key.
"
5.3.13 NIBP module, M-NIBP
1.
2.
Check the function of the front panel membrane keys.
Attach an adult NIBP cuff onto your arm and perform one NIBP measurement.
Check that the module identifies the cuff, i.e. the text ‘Adult ’ appears on the NIBP digit field for
a short time.
Check that the module gives a reasonable measured result.
"
55
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
5.3.14 Nellcor Compatible Saturation module, E-NSAT/ M-NSAT
1.
2.
Connect a Nellcor SpO2 finger probe to the module. Check that the message ‘Pulse search ’ is
shown. Check also that the shown message changes to ‘Check probe ’ within 30 seconds.
Attach the SpO2 probe on your finger. Check that a reading of 95-100 and a proper SpO2
waveform appear.
"
5.3.15 Datex-Ohmeda Oxygen Saturation module, M-OSAT
1.
2.
Connect an OxyTip ® + Reusable Finger Sensor such as Integrated Finger Sensor OXY-F4-N to
the module. Check that the message ‘No Probe’ in the screen changes to ‘Check probe’.
Attach the SpO2 probe on your finger. Check that a reading of 95-100 and a proper SpO2
waveform appear.
"
5.3.16 BIS Module, E-BIS/ M-BIS
1.
2.
3.
Connect the BIS module to the monitor frame.
Check that ‘Cable off’ is displayed in the BIS waveform field.
Connect the DSC to the module.
Check that the ‘No sensor’ message appears in the waveform field.
Check the function of the front panel membrane keys.
Open the BIS Setup menu: BIS - BIS Setup and check that Test DSC shows PASS.
NOTE: If the sensor is not connected, the Check Sensor key is inoperative.
"
5.3.17 Entropy Module, E-ENTROPY/ M-ENTROPY
1.
2.
3.
Check the function of the front panel membrane keys.
Connect the Entropy sensor cable and Entropy simulator to the module. Check that ‘Checking
sensor’ text and an image appear in the waveform numeric field. Wait for a while and check that
all sensors show PASS.
Check that the EntrEEG waveform and RE and SE values appear on the monitor screen.
"
5.3.18 Data Card and Menu Card function
1.
Insert a Data card or a Menu card to the slot.
Check that the corresponding symbol appears on the monitor screen.
"
56
Document no. M1031517-02
Functional check
5.3.19 Recorder
1.
2.
Press the Record Wave module key and check that the module starts recording the selected
waveforms. Press the Stop module key to stop recording.
Check that the quality of the recordings is acceptable.
"
5.3.20 Network connection
1.
Check that the Mon-Net cable connector and the Identification plug are clean and intact, then
connect them to the frame unit.
Check that the monitor connects to the network, i.e. the network symbol appears on the upper
right-hand corner of the screen. Also a message regarding the connected Central should appear
in the message field on the screen.
"
5.3.21 Wireless Network Option
1.
2.
Check that the green LED on the wireless antenna card blinks and the WLAN signal strenght
symbol scrolls between zero and full or stays fixed on the monitor screen.
Check that the wireless LAN network symbol appears on the upper right-hand corner of the
screen when the monitor connects to the Datex-Ohmeda Network.
NOTE: If the monitor does not connect to the Datex-Ohmeda Network, check the WLAN configuration
on the monitor and on the network.
"
5.3.22 Interface Module, E-INT/ M-INT
1.
Make sure that the monitor receives all necessary parameter data from the connected devices.
Check the screen configuration and the related interfacing settings, if necessary.
Monitor Setup – Interfacing
"
5.3.23 Device Interfacing Solution, N-DISxxx
1.
Make sure that the monitor receives all necessary parameter data from the connected devices.
Check the screen configuration and the related interfacing settings, if necessary.
Monitor Setup - Interfacing - Status Page
"
57
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
5.3.24 General
•
•
•
Switch the monitor to standby
Perform final cleaning
Fill in all necessary documents
"
58
Document no. M1031517-02
General troubleshooting
General troubleshooting
Monitor not
functioning
Power cord
connected?
No
Connect power
cord
Yes
Monitor can be
started now?
Yes
Batteries were
empty
No
Possible AC/DC
unit failure.
Replace AC/DC
unit.
No
On/Standby LED
is ON or blinks?
Yes
Frame Unit fan is
running?
Monitor can be
started now?
Yes
Yes
Display Unit
failure.
AC/DC Unit
failure.
No
PMB failure.
Replace PMB.
Figure 17
No
CM1_trbl_Flowchart.vsd
6
S/5 Compact Monitor general troubleshooting flowchart
59
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
60
Document no. M1031517-02
Appendix A, Functional check form, Datex-Ohmeda S/5 CAM, CCCM
APPENDIX A Functional check form,
Datex-Ohmeda S/5 CAM, CCCM
Customer
Service
Service engineer
Date
Monitor Installation
Frame: F-CM________
System options:
E/M-
Software:
N-
E/M-
K-
N-
E/M-
K-
N-
E/M-
OK = Test OK
N.A. = Test not applicable
Visual Inspection
Fail = Test failed
OK
N.A.
Fail
OK
N.A.
Fail
1. Check all units visually
Functional Inspection
5.3.1. General
5.3.2. Display
5.3.3. Keyboard(s)
S/N
5. Functional check
S/N
5.3.5. Display unit
Notes
5.3.6. Compact Airway Module, E-CXXXXX/ M-CXXXXX
S/N
. Compact Airway Modules with the Patient Spirometry option
. For all Compact Airway Modules
5.3.7. Single width Airway Module, E-miniC/ M-miniC
S/N
A-1
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Functional Inspection
OK
Notes
5.3.8. Tonometry Module, E-TONO/ M-TONO
S/N
5.3.9. Multiparameter Hemodynamic Modules
S/N
. ECG and RESP measurements
. Temperature measurement
. Invasive blood pressure measurement
. SpO2 measurement
. Non invasive blood pressure measurement
Notes
5.3.10. Pressure/Pressure Temp Modules, E-P, E-PT,
M-P, M-PT
S/N
. Invasive blood pressure measurement
. Temperature measurement
5.3.11. Dual pressure Module, E-PP/ M-PP
S/N
Notes
5.3.12. Cardiac Output Modules, E-COP/ M-COP,
E-COPSv/ M-COPSv
S/N
. Invasive blood pressure measurement
. Cardiac Output measurement
Notes
5.3.13. NIBP module, M-NIBP
S/N
5.3.14. Nellcor Compatible Saturation module, E-NSAT/
S/N
M-NSAT
A-2
Document no. M1031517-02
N.A.
Fail
Appendix A, Functional check form, Datex-Ohmeda S/5 CAM, CCCM
Functional Inspection
OK
5.3.15. Datex-Ohmeda Oxygen Saturation module,
M-OSAT
S/N
5.3.16. BIS Module, E-BIS/ M-BIS
S/N
5.3.17. Entropy Module, E-ENTROPY/ M-ENTROPY
S/N
5.3.18. Data Card and Menu Card function
S/N
5.3.19. Recorder
S/N
5.3.20. Network connection
S/N
5.3.21. Wireless Network Option
S/N
5.3.22. Interface Module, E-INT/ M-INT
S/N
5.3.23. Device Interfacing Solution, N-DISxxx
S/N
N.A.
Fail
Notes
5.3.24. General
• Perform final cleaning
• Fill in all necessary documents
Notes
Signature
A-3
Document no. M1031517-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
For your notes:
A-4
Document no. M1031517-02
Appendix B, ElectroMagnetic Compatibility
APPENDIX B ElectroMagnetic Compatibility
Table 1
Guidance and manufacturer’s declaration – electromagnetic emissions
Guidance and manufacturer’s declaration – electromagnetic emissions
The S/5™ CAM/ CCCM is intended for use in the electromagnetic environment specified below. The customer or
the user of the S/5™ CAM/ CCCM should assure that it is used in such an environment.
Emissions test
Compliance
Electromagnetic environment - guidance
RF emissions
CISPR 11
Group 1
The S/5™ CAM/ CCCM uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not likely to cause any
interference in nearby electronic equipment.
RF emissions
CISPR 11
Group 2 (1
The S/5™ CAM/ CCCM must emit electromagnetic energy in order to
perform its intended function. Nearby electronic equipment may be
affected.
RF emissions
CISPR 11
Class B
Harmonic emissions
IEC 61000-3-2
Class A
The S/5™ CAM/ CCCM is suitable for use in all establishments,
including domestic establishments and those directly connected to
the public low-voltage power supply network that supplies buildings
used for domestic purposes.
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Complies
(1
S/5™ CAM/ CCCM equipped with N-CMW option
B-1
Document no. M1031517-02
Table 2
Guidance and manufacturer’s declaration – electromagnetic immunity
Guidance and manufacturer’s declaration – electromagnetic immunity
The S/5™ CAM/ CCCM is intended for use in the electromagnetic environment specified below. The customer or the
user of the S/5™ CAM/ CCCM should assure that it is used in such an environment.
Immunity test
Compliance level
Electromagnetic environment - guidance
Electrostatic discharge ±6 kV contact
(ESD)
IEC 61000-4-2
±8 kV air
±6 kV contact
Floors should be wood, concrete or
ceramic tile. If floors are covered with
synthetic material, the relative humidity
should be at least 30 %.
Electrical fast
transients/bursts
IEC 61000-4-4
±2 kV for power supply
lines
±1 kV for input/output
lines
±2 kV for power supply Mains power quality should be that of a
lines
typical commercial or hospital
±1 kV for input/output environment.
lines
Surge
IEC 61000-4-5
±1 kV differential
mode
±2 kV common mode
±1 kV differential mode Mains power quality should be that of a
±2 kV common mode typical commercial or hospital
environment.
Voltage dips, short
interruptions and
voltage variations on
power supply lines
IEC 61000-4-11
<5 % UT
(>95 % dip in UT)
for 0.5 cycle
<5 % UT
(>95 % dip in UT)
for 0.5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
<5 % UT
(>95 % dip in UT)
for 5 sec
<5 % UT
(>95 % dip in UT)
for 5 sec
3 A/m
3 A/m
Power frequency
(50/60 Hz) magnetic
field
IEC 61000-4-8
IEC 60601 test level
±8 kV air
NOTE: UT is the a.c. mains voltage prior to application of the test level.
B-2
Document no. M1031517-02
Mains power quality should be that of a
typical commercial or hospital
environment. If user of the S/5™ CAM/
CCCM requires continued operation during
power mains interruptions, it is
recommended that the S/5™ CAM/ CCCM
be powered from an uninterruptible power
supply or a battery.
Power frequency magnetic field should be
at levels characteristic of a typical location
in a typical commercial or hospital
environment.
Appendix B, ElectroMagnetic Compatibility
Table 3
Guidance and manufacturer’s declaration – electromagnetic immunity
Guidance and manufacturer’s declaration – electromagnetic immunity
The S/5™ CAM/ CCCM is intended for use in the electromagnetic environment specified below. The customer or the
user of the S/5™ CAM/ CCCM should assure that it is used in such an environment.
Immunity test
IEC 60601 test level
Compliance
level
Electromagnetic environment - guidance
Portable and mobile RF communications equipment
should be used no closer to any part of the S/5™ CAM/
CCCM, including cables, than the recommended
separation distance calculated from the equation
applicable to the frequency of the transmitter.
Recommended separation distance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 kHz to 80 MHz
3 Vrms
d = 1.2 P
3 Vrms
150 kHz to 80 MHz
1 Vrms (1
d = 3.5 P
3 V/m
80 MHz to 2.5 GHz
3 V/m
d = 1.2 P
80 MHz to 800 MHz
d = 2.3 P
800 MHz to 2.5 GHz
d = 3.5 P
80 MHz to 800 MHz
d = 7 P
800 MHz to 2.5 GHz
3 V/m
80 MHz to 2.5 GHz
1 V/m (2
where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in metres (m).
Field strengths from fixed RF transmitters, as determined
by an electromagnetic site survey, a should be less than
the compliance level in each frequency range. b
Interference may occur in the vicinity of equipment
marked with the following symbol:
B-3
Document no. M1031517-02
NOTE 1
NOTE 2
At 80 MHz and 800 MHz, the higher frequency range applies.
These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and
land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted
theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in the location in which
the S/5™ CAM/ CCCM is used exceeds the applicable RF compliance level above, the S/5™ CAM/ CCCM
should be observed to verify normal operation. If abnormal performance is observed, additional measures
may be necessary, such as reorienting or relocating the S/5™ CAM/ CCCM.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
(1
For impedance RESP measurement. For invasive pressure measurement in M-series modules
except M-PRE(S)TN. The invasive pressure measurement compliance level is dependent on the
transducer used, and only the lower level is guaranteed for all transducers.
(2
For BIS measurement in E-BIS/M-BIS, RESP measurement in M-(P)RE(S)TN and invasive
pressure measurement in M-COPSv/E-COPSv and M-COP/E-COP modules. The invasive
pressure measurement compliance level is dependent on the transducer used, and only the
lower level is guaranteed for all transducers.
B-4
Document no. M1031517-02
Appendix B, ElectroMagnetic Compatibility
Table 4
Recommended separation distances between portable and mobile RF
communications equipment and the S/5™ CAM/ CCCM
Recommended separation distances between portable and mobile RF communications
equipment and the S/5™ CAM/ CCCM.
The S/5™ CAM/ CCCM is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of the S/5™ CAM/ CCCM can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and
the S/5™ CAM/ CCCM as recommended below, according to the maximum output power of the communications
equipment.
Rated maximum output
power of transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz
d = 1.2 P
d = 3.5 P
0.01
0.1
1
(1
d = 3.5 P
d = 2.3 P
(2
d = 7 P
0.12
0.23
0.35 (1
0.35 (2
0.70 (2
0.38
0.38
0.73
1.1 (1
1.1 (2
2.2 (2
1.2
1.2
2.3
(1
3.8
11
100
d = 1.2 P
80 MHz to 800 MHz
0.12
3.5
10
80 MHz to 800 MHz
3.8
(1
12
35
3.5
(2
11
35
7.0 (2
7.3
(2
12
(1
(2
22 (2
23
(2
70 (2
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in
meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the
maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1
At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2
These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
(1
For impedance RESP measurement. For invasive pressure measurement in M-series modules
except M-PRE(S)TN. The invasive pressure measurement compliance level is dependent on the
transducer used, and only the lower level is guaranteed for all transducers.
(2
For BIS measurement in E-BIS/M-BIS, RESP measurement in M-(P)RE(S)TN and invasive
pressure measurement in M-COPSv/E-COPSv and M-COP/E-COP modules. The invasive
pressure measurement compliance level is dependent on the transducer used, and only the
lower level is guaranteed for all transducers.
B-5
Document no. M1031517-02
For your notes:
B-6
Document no. M1031517-02
Datex-Ohmeda
S/5TM Compact Anesthesia Monitor
S/5TM Compact Critical Care Monitor
Planned Maintenance Instructions
All specifications are subject to change without notice.
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
Document no. M1031518-02
March, 2006
Datex-Ohmeda Inc.
P.O. Box 7550
Madison, WI 53707-7550, USA
Tel: +1 608 221 1551
Fax: +1 608 222 9147
GE Healthcare Finland Oy
Helsinki, Finland
P.O. Box 900
FI-00031 GE, FINLAND
Tel: +358 10 39411
Fax: +358 9 1463310
www.gehealthcare.com
Copyright  2006 General Electric Company
Table of contents
Table of contents
Table of contents
i
1
1
Planned maintenance instructions
1.1
1.2
1.3
1.4
2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Recommended tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2.1
Hemodynamic patient simulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Recommended parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Planned maintenance parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4.1
PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX without CO2 absorber
- Anesthesia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4.2
PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX without CO2 absorber
- Critical Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4.3
PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX with CO2 absorber
- Anesthesia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4.4
PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX with CO2 absorber
- Critical Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4.5
PM parts for Airway Module, E-miniC/ M-miniC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Planned maintenance check list
2.1
2.2
8
Visual inspection/preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.2
Compact Airway Module, E-CXXXXX/ M-CXXXXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.3
Single-width Airway Module, E-miniC/ M-miniC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.4
Tonometry Module, E-TONO/ M-TONO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.5
Recorder Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.6
Modules with NIBP measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Functional inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.2.1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.2.2
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.2.3
Keyboard(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.2.4
Display Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.2.5
Frame Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.2.6
Compact Airway Module, E-CXXXXX/ M-CXXXXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.2.7
Single-width Airway Module, E-miniC/ M-miniC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.2.8
Tonometry Module, E-TONO/ M-TONO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.2.9
Multiparameter Hemodynamic Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.2.10 EEG Module, E-EEG/ M-EEG and EEG Headbox, N-EEG. . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.2.11 BIS Module, E-BIS/ M-BIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.2.12 Entropy Module, E-ENTROPY/ M-ENTROPY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
2.2.13 Pressure/Pressure Temp Modules, E-P, E-PT, M-P, M-PT. . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.2.14 Dual pressure Module, E-PP, M-PP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.2.15 Cardiac Output Modules, E-COP, E-COPSv, M-COP, M-COPSv . . . . . . . . . . . . . . . . . . . . . . .19
2.2.16 NIBP module, M-NIBP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.2.17 NeuroMuscular Module, E-NMT, M-NMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.2.18 Nellcor Compatible Saturation module, E-NSAT, M-NSAT . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.2.19 Datex-Ohmeda Oxygen Saturation module, M-OSAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
i
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.2.20
2.2.21
2.2.22
2.2.23
2.2.24
2.2.25
2.2.26
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Network Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Wireless Network Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Interface Module, E-INT, M-INT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Device Interfacing Solution, N-DISxxx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Appendix A: Planned maintenance check form, S/5 Compact Monitors
ii
Document no. M1031518-02
A-1
Planned maintenance instructions
1
Planned maintenance instructions
1.1
Introduction
These instructions include procedures for planned maintenance (PM) for the Datex-Ohmeda S/5
Compact Anesthesia Monitor and S/5 Compact Critical Care Monitor. The Planned maintenance
should be performed once a year.
These instructions include “Planned maintenance check form, S/5 Compact Monitors” to be filled in
when performing the corresponding procedures.
The symbol
" in the instructions means that the procedure performed should be signed in the
check form.
The procedures should be performed in ascending order, bypassing those that are not applicable for
a particular monitor.
If you need further information on how to perform a certain Planned maintenance procedure, please
refer to the corresponding slot in the Technical Reference Manual.
All menu selections related to the Datex-Ohmeda monitors are written in the following typeface:
e.g. Parameters - Gas Unit
As you enter the service menus, you need following passwords:
Monitor Setup - Install/Service (password 16-4-34) - Service (password 26-23-8)
In case you evaluate the measurement accuracy with a patient simulator, add the simulator’s
accuracy specification to the one for the monitor.
1.2
Recommended tools
For product(s)
Tool
Order No.
All Airway modules
Flowmeter
Compact Airway Module, E-CAiO(VX)/
M-CAiO(VX)
Calibration gas and regulator
755583/755534*
Compact Airway Module, E-COVX/ M-COVX
Calibration gas and regulator
755587/755534*
Compact Airway Module, E-CO(V), M-C,
M-CO(V)
Calibration gas and regulator
755581/755534*
E-miniC/ M-miniC
Calibration gas and regulator
755580/755534*
Compact Airway Module, E-COVX, E-CAiOVX,
M-COVX, M-CAiOVX
Sampling line, 2 m
73318
All Airway modules w/ (V)
Spirometry tube, 2 m
890031
All Airway modules w/ (V)
D-lite
733950
All Airway modules
Sampling line, 6 m/19.7 ft
73306
NIBP cuff and hose
2753E (cuff)
877235 (hose)
Hemodynamic modules
Hemodynamic modules w/ (P),
M-NIBP
1
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
For product(s)
Tool
Order No.
Hemodynamic modules w/ (P)
InvBP transducer
70077-001
Multi-Link ECG accessories, IEC
E-PSM(P)/ E-PRESTN/ M-PRESTN
-
Multi-link 3-leadwire set
412682-003
-
Multi-link 5-leadwire set
412681-003
-
Multi-link 5-leadwire set, C2-C6
416467-004
E-PRESTN/ M-PRESTN w/ (E12)
-
Multi-link 12-lead ECG trunk cable 416035-002
or
Multi-Link ECG accessories, AHA
E-PSM(P)/ E-PRESTN/ M-PRESTN
-
Multi-link 3-leadwire set
412682-001
-
Multi-link 5-leadwire set
4162681-001
-
Multi-link 5-leadwire set, V2-V6
416467-003
E-PRESTN/ M-PRESTN w/ (E12)
-
Multi-link 12-lead ECG trunk cable 416035-001
M-NESTPR
3-lead ECG trunk cable
545302
M-NESTPR
5-lead ECG cable
545303
M-NE12STPR
10-leadwire ECG cable
545324
E-PSM(P)/ E-PRESTN
SpO2 finger probe
OXY-F-UN
SpO2 Interconnect Cable
OXY-ES3
M-PRESTN
SpO2 finger probe
OXY-F4-N or SAS-F4
E-NSAT/ M-NSAT
Nellcor SpO2 probe
Hemodynamic modules w/ (T)
Temperature test set
884515
Hemodynamic E-Modules w/ (NIBP)
Adult NIBP cuff hose with cuff ID
2021285-001
Infant cuff hose without cuff ID
414874-001
Adult NIBP cuff
572435
Adult NIBP cuff hose
877235
E-COP, E-COPSv, M-COP, M-COPSv
C.O. Catheter cable
16590
E-COPSv/ M-COPSv
SvO2 simulator
890121
Tonometry Module, E-TONO/ M-TONO
Calibration gas and regulator
755580/755534
Sampling line
733251
Hemodynamic M-Modules w/ (NIBP)
Luer plug
Pressure manometer
TonometricsTM catheter
EEG Module, E-EEG/ M-EEG
Earphones
EEG simulator
2
Document no. M1031518-02
TONO-14F or another
suitable TONO-_F catheter
90502
Planned maintenance instructions
For product(s)
Tool
Order No.
BIS Module, E-BIS/ M-BIS
BIS simulator or
BIS Sensor simulator
900509
900508
E-ENTROPY/ M-ENTROPY
Simulator for M-ENTROPY
N-ES
Entropy sensor cable
8002964
NMT simulator
871251
NMT ElectroSensor
888416
NMT sensor cable
888415
MemCard – Menu
893860 (English)
MemCard – Data
887045 (English)
E-NMT/ M-NMT
All M-Modules
Screwdrivers
All E-Modules
Torx screwdrivers; T8, T10
NOTE: * Ensure that the calibration gas and regulator are functioning properly before calibration.
Perform annual maintenance on the regulator as required. For more information see section
“Adjustments and calibrations” in Compact Airway modules slot.
1.2.1 Hemodynamic patient simulators
The following tables present the patient simulators’ compatibility with each hemodynamic module, and the
accessories needed:
Table 1
Patient simulators’ compatibility with each hemodynamic module
Patient simulator
Module
Parameter
M1010831
MedSim
874027
E-PSM(P),E-PRESTN
ECG
Ok
Multilink ECG acc.
Not compatible
T
402015-004
402015-004 and
M1010832
InvBP
Ok
M1010858
ECG
3
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Patient simulator
Module
Parameter
M1010831
MedSim
874027
M-PRESTN
ECG
Ok
Multilink ECG acc.
Not compatible
T
Ok
M1010832
M1010832
InvBP
Not compatible
Ok
Ok
ECG
Not compatible
300 series acc.
Ok
12 lead ECG Not compatible
300 series acc.
Not compatible
T
Ok
M1010832
M1010832
InvBP
Not compatible
Ok
Ok
Auto
On/Off
Start
Cancel
Zero
P1
Zero
P2
SpO2
NIBP
ECG
T1
P1
T2
P2
M-NESTPR
NIBP
T1
ECG+
Resp
P1
T2
P2
SpO
2
Table 2
Adapter cables for hemodynamic patient simulators
Patient simulator
Adapter cables for simulators
Hemodynamic patient simulator
Dual temperature adapter cable
402015-004
Hemodynamic patient simulator
Dual Inv.BP adapter cable
2005772-001
Medsim
Temperature adapter cable
M1010832
Medsim
Inv.BP adapter cable
M1010858
Lionheart & MPS450
Temperature adapter cable
M1010846
Lionheart & MPS450
Inv.BP adapter cable
M1010862
For product(s)
Part
Order No.
CM(C) Frame Unit
Fan filter
896085
CM(C) Display Unit
Fan filter
874594
Central Processing Board
Battery for SRAM/Timekeeper
197230
Recorder paper
74205
1.3
Recommended parts
Tonometry Module, E-TONO/ M-TONO
4
Document no. M1031518-02
733382
Planned maintenance instructions
1.4
Planned maintenance parts
1.4.1 PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX without CO2 absorber
- Anesthesia
Part
Order No.
For product(s)
Special tube (Nafion)
733382
All Airway modules
Ref. gas sticker
893110
Compact Airway Modules
Filter (2 pcs)
886136
Compact Airway Modules
Filter assembly
896025
Compact Airway Modules
Fan filter
886236
Compact Airway Modules
D-fend O-ring (2 pcs)
653125
All Airway modules
D-fend (black)
876445
All Airway modules
Sampling line 2.0 m
73318
Compact Airway Modules
PM sticker
893108
All Airway modules
NOTE: Corresponding PM kit is available with Order No. 8001758.
1.4.2 PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX without CO2 absorber
- Critical Care
Part
Order No.
For product(s)
Special tube (Nafion)
733382
All Airway modules
Ref. gas sticker
893110
Compact Airway Modules
Filter (2 pcs)
886136
Compact Airway Modules
Filter assembly
896025
Compact Airway Modules
Fan filter
886236
Compact Airway Modules
D-fend O-ring (2 pcs)
653125
All Airway modules
D-fend+ (green)
893200
All Airway modules
Sampling line 2.0 m
733162
Compact Airway Module, M-COVX
PM sticker
893108
All Airway modules
NOTE: Corresponding PM kit is available with Order No. 8001759.
5
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.4.3 PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX with CO2 absorber
- Anesthesia
Part
Order No.
For product(s)
Special tube (Nafion 2 pcs)
733382
All Airway modules
Ref. gas sticker
893110
Compact Airway Modules
Filter (2 pcs)
886136
Compact Airway Modules
Filter assembly
896025
Compact Airway Modules
Fan filter
886236
Compact Airway Modules
D-fend O-ring (2 pcs)
653125
All Airway modules
D-fend (black)
876445
All Airway modules
Sampling line 2.0 m
73318
Compact Airway Modules
PM sticker
893108
All Airway modules
NOTE: Corresponding PM kit is available with Order No. 8001760.
1.4.4 PM parts for Compact Airway Modules, E-CXXXXX/ M-CXXXXX with CO2 absorber
- Critical Care
Part
Order No.
For product(s)
Special tube (Nafion 2 pcs)
733382
All Airway modules
Ref. gas sticker
893110
Compact Airway Modules
Filter (2 pcs)
886136
Compact Airway Modules
Filter assembly
896025
Compact Airway Modules
Fan filter
886236
Compact Airway Modules
D-fend O-ring (2 pcs)
653125
All Airway modules
D-fend+ (green)
893200
All Airway modules
Sampling line 2.0 m
733162
Compact Airway Module, M-COVX
PM sticker
893108
All Airway modules
NOTE: Corresponding PM kit is available with Order No. 8001761.
6
Document no. M1031518-02
Planned maintenance instructions
1.4.5
PM parts for Airway Module, E-miniC/ M-miniC
Part
Order No.
For product(s)
Special tube (Nafion 2 pcs)
733382
All Airway modules
Mini D-fend O-ring (2 pcs)
656565
E-miniC/ M-miniC
Mini D-fend
8002174 (pkg of 10 pcs)
E-miniC/ M-miniC
Zero valve air filter
M1011471
E-miniC, every 3 years
Zero valve air filter
571421
M-miniC
CO2 Sampling line 3.0 m
733163
E-miniC/ M-miniC
PM sticker
893108
All Airway modules
For details on recommended accessories see the “Supplies and Accessories” catalog.
7
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2
Planned maintenance check list
2.1
Visual inspection/preparation
2.1.1
General
NOTE: Wear a static control wrist strap when handling PC boards. Electrostatic discharge may
damage components on the board.
1.
2.
3.
4.
Make sure that the monitor is switched to standby.
Disconnect the mains power cord. If the monitor is connected to the Datex-Ohmeda Network,
disconnect the Mon-Net cable from the monitor. Disconnect the WLAN antenna card, if the
Wireless LAN option is installed.
Check all the units visually. Check that all parts are intact and that the cables and screws are
connected and tightened properly.
Especially check the following parts:
−
the equipotential tap and all the screws are tightened properly.
−
the display unit locking screw is in a locking position.
Check that modules go in smoothly and lock up properly in all module slots.
Insert the WLAN antenna card back into the foremost card slot, if the Wireless LAN option is
installed.
Replace the batteries, if necessary.
The manufacturer recommendations are:
−
Replace the SRAM/Timekeeper battery on the CPU board every 8 years.
NOTE: The Factory Reset must be performed if the SRAM/Timekeeper battery is replaced.
NOTE: If the monitor is used for frequent short transportation, refresh the batteries every two
weeks and replace the batteries every six months.
Clean or replace the fan filters in the frame unit and display unit.
Check that the fuses are of the correct rating.
"
2.1.2
Compact Airway Module, E-CXXXXX/ M-CXXXXX
1.
2.
Detach the module box.
Check that all cables and tubes are connected properly and that there are no loose objects
inside the module.
NOTE: The tubes connected to the Oxygen board pressure transducers should not be pressed
too deep.
NOTE: Make sure that the tubes are not in contact with the sampling pump or the O2 sensor, or
its springs.
Install the PM Kit:
−
Replace the special tubes (Nafion™).
−
Replace the Ref. filter assembly.
−
Replace the filters in the pneumatic unit (1 or 2 pcs).
8
Document no. M1031518-02
Planned maintenance check list
3.
−
Check the D-fend O-rings and replace them, if necessary.
−
Replace the D-fend and sampling line.
−
Clean or replace the fan filter.
NOTE: Use only approved sampling lines to ensure proper functioning.
Use a 2 m/7 ft. sampling line with Compact Airway Modules E-/ M-COVX and E-/ M-CAiOVX.
The manufacturer recommendation is to replace the CO2 absorber every 4 years. Replace the
absorber, if necessary.
Note: All Compact Airway Modules do not contain a CO2 absorber.
"
Connect the Compact Airway Module to a module slot with a long gas interface cable (the
grounding plates of the cable should be removed for the procedure).
2.1.3
Single-width Airway Module, E-miniC/ M-miniC
1.
Detach the module box.
2.
Check that all cables and tubes are connected properly and that there are no loose objects
inside the module.
Install the PM Kit:
−
Replace the special tube (Nafion™).
−
Replace the Zero valve air filter every three years.
−
Check the D-fend body connector O-rings and replace them, if necessary.
−
Replace the Mini D-fend and the sampling line.
NOTE: Use only approved sampling lines to ensure proper functioning.
Connect the module to a module slot with a long gas interface cable (the grounding plates of the
cable should be removed for the procedure).
3.
4.
"
2.1.4
Tonometry Module, E-TONO/ M-TONO
1.
2.
Detach the module box.
Check that all cables and tubes are connected properly and that there are no loose objects
inside the module.
Replace the Special tube (Nafion 2 pcs).
Reattach the module box and check that the latch moves properly. Plug the module back into
the module frame.
"
2.1.5
Recorder Unit
1.
Clean the recorder.
−
Open the paper compartment hatch and remove the paper roll, if installed.
−
Remove any paper chaff from the paper compartment.
9
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
−
Clean the thermal printhead and the small glass window in front of the static brush with a
cotton swab dipped in isopropyl alcohol, if necessary.
NOTE: Avoid contact with the rubber paper roller. Be careful to limit the application of alcohol to
the thermal printhead and the window.
−
Reinstall the paper roll.
"
2.1.6
Modules with NIBP measurement
1.
Check the NIBP pump filter. Replace the filter, if necessary.
Note: M-NIBP Rev. 00-03 do not contain a NIBP pump filter.
Plug the module back into the frame.
"
2.2
Functional inspection
2.2.1
General
1.
2.
3.
Connect the mains power cord. Check that the LED above the mains switch is lit continuously
(full charged batteries) or periodically (charging batteries).
Switch the monitor on.
Check that the monitor starts up properly, i.e. the alarm LEDs and the display unit fan turn on
shortly, normal start-up sound is heard from the loudspeaker and the monitoring screen
appears.
No error messages should appear on the screen.
Configure the screen for the parameters that are connected.
Check that all the connected modules are recognized, i.e. the required parameter information is
shown on the screen.
If installed, the recorder should record two lines of start-up information.
Preset the measurement settings for those parameters that are connected, for example:
Others - EEG - Montage - EEG Channels - 4
- Montage type - Bip
Others - EEG - EEG Setup - Numeric 1 - MF
- Numeric 2 - Ampl.
Others - EP - Cycle - Cont.
- AEP Setup - AEP Channels - 2
- Responses -100
- Stim. Frequency - 1.1Hz
- Stim. Intensity - 90 dB
- Sweep length - 100 ms
- EP size - 1
10
Document no. M1031518-02
Planned maintenance check list
Recorder - Record Waveforms - Waveform 1 - ECG1
- Waveform 2 - P1
- Waveform 3 - P2
Invasive Pressures - P1 ‘ART’ Setup - Label - ART
- P2 ‘CVP’ Setup - Label - CVP
- P3 Setup - Label - PA
- P4 Setup - Label - P4
- P5 Setup - Label - P5
- P6 Setup - Label - P6
Pulse Oximetry - Pleth Scale - AUTO
or
Others - SPO2 Setup - Pleth Scale - AUTO
Airway Gas - Spirometry View - Scaling - Indep.
- Paw Scale - 20
- Flow Scale - 15
or
Ventil. - Spirometry Setup - Scaling - Indep.
- Paw Scale - 20
- Flow Scale - 15
Others - C.O. View - C.O. Setup - Scale - 1.0 °C
- Injectate Volume - 10 ml
- Measurement Mode - SET
Others - SvO2 - Update HGB - 115 g/l
or
Wedge C.O: SVO2 - C.O. View - C.O. Setup - Scale - 1.0 °C
- Injectate Volume - 10 ml
- Measurement Mode - SET
Wedge C.O: SVO2 - SvO2 - Update HGB - 115 g/l
Others - NMT - Stimulus Mode - TOF
- Set Cycle Time - 10 sec.
Others - NMT -NMT Setup - Current - s(70mA)
- Pulse Width - 200 ms
- Stim. Beep Volume - 2
Others - Resp Setup
- Size - 1.0
- Resp Rate Source - AUTO
- Measurement - ON
- Detection Limit - AUTO
11
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.2.2
Display
1.
2.2.3
Check that the picture on the screen is adjusted correctly.
"
Keyboard(s)
1.
Tests with the Command Board:
−
Press the Help key. Turn the ComWheel in both directions and check that the cursor in the
menu moves correspondingly. Select Normal Screen and check that the menu
disappears from the screen.
Check the rest of the menu keys by pressing them one by one.
Tests with the ARK Keyboard:
−
Enter the Keyboard service menu
−
Check the function of the ComWheel.
−
Press all keys, except Modify and Print. Check that each key produces a sound from the
loudspeaker, or the ‘Message count’ value in the service menu increases.
−
Press the Modify and Print keys and check that the corresponding menus appear on the
monitor screen.
Tests with the Remote Controller:
−
Enter the Keyboard service menu.
−
Check the function of the ComWheel.
−
Press all keys. Check that each key produces a sound from the loudspeaker, or the
Message count value in the service menu increases.
2.2.4
Display Unit
1.
2.
Check that the clock on the screen shows correct time.
Readjust the time and date, if necessary.
Enter the Service Log service menu.
Check the content of the Service Log for possible problems.
"
2.2.5
Frame Unit
1.
Check that the Frame unit fan is running.
"
2.2.6
Compact Airway Module, E-CXXXXX/ M-CXXXXX
1.
2.
Check that the fan is running.
If the module contains membrane keys on the front panel, press each of the keys for at least
one second and check that they are identified.
NOTE: The Compact Airway Module membrane keys require S/5 main software.
12
Document no. M1031518-02
Planned maintenance check list
3.
4.
5.
6.
7.
8.
9.
Wait until the message ‘Calibrating gas sensor’ disappears from the screen, then enter the
Compact Airway Module General service menu.
Check that the module configuration displayed corresponds with the Compact Airway Module
type being used.
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second.
Enter the Gases service menu: Check that the ‘Ambient’ value displayed corresponds with the
current ambient pressure (±20 mmHg).
Check that the flow measurement offset, i.e. the sample ‘Zero’ value displayed is within ±10
ml/min.
Perform a sampling system leak test.
Check the flow rates. Adjust the sampling flow, if necessary.
Perform a gas calibration:
NOTE: For maximum accuracy, a warm-up time of 30 minutes is recommended.
NOTE: For correct measurement values, modules need different amounts of oxygen in the
calibration. If you do not use the recommended calibrating gases, the calibration does not
succeed.
"
Anesthesia Agent
Compact Airway Modules w/ the option
10. Enter the Gases service menu.
Feed calibrating gas (order code 755583) continuously for at least 30 seconds and check that
the ‘ID’ in the service menu shows ‘DES’ and that the value for ‘ID unrel.’ is lower than 50.
"
Patient Spirometry
Compact Airway Modules w/ the option
11. Enter the Spirometry service menu.
Connect a clean spirometry tube and D-lite to the module.
Perform the spirometry leak test.
12. Connect the sampling line. Breathe through the wider side of the D-lite. Check that the flow
waveform moves downwards when you breathe in, and upwards when you breathe out.
"
General
For all Compact Airway Modules
• Switch the monitor to standby and reassemble the module.
NOTE: Attach the plastic cover to the CPU Board before fitting the module box. Make sure that
the grounding claws in the front panel frame make good contact with the module box.
13
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
NOTE: When reassembling the module, make sure that the tubes are not pinched between the
module box and internal parts.
Insert the Compact Airway Module into the frame. Switch the monitor back on and wait until the
message ‘Calibrating gas sensor’ disappears from the screen.
13. Block the tip of the sampling line with your finger and check that the message ‘Sample line
blocked’ appears on the monitor screen within 30 seconds.
14. Detach the D-fend and check that the message ‘Check D-fend’ appears on the monitor screen
within 60 seconds.
"
2.2.7
Single-width Airway Module, E-miniC/ M-miniC
1.
2.
3.
4.
5.
6.
7.
8.
Wait until the message ‘Calibrating gas sensor’ disappears from the screen, then enter the Gas
Unit General service menu.
NOTE: The Airway Module M-miniC requires S/5 main software L-CANE02(A) / L-CICU02(A) or
later.
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second.
Enter the Gases service menu: Check that the ‘Ambient’ value displayed corresponds with the
current ambient pressure (±20 mmHg).
Check that the flow measurement offset, i.e. the sample ‘Zero’ value displayed is within ±10
ml/min.
Perform a sampling system leak test.
Check the flow rates. Adjust the sampling flow, if necessary.
Block the tip of the sampling line with your finger and check that the message ‘Sample line
blocked’ appears on the monitor screen within 30 seconds.
Remove the Mini D-fend and check that the message ‘Check D-fend’ appears on the screen
within 30 seconds.
Perform a gas calibration:
NOTE: For maximum accuracy, a warm-up time of 30 minutes is recommended.
"
2.2.8
Tonometry Module, E-TONO/ M-TONO
1.
Enter the TONO service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second.
Check that the memories of the module have passed the internal memory test, i.e. RAM, ROM
and EEPROM all state OK.
Check that the ‘general error status’, ‘module pneumatics error status’, ‘module hardware error
status’ and ‘testbit status’ are all zero.
2.
3.
4.
Check the function of the front panel Start-Stop and Lab Data membrane keys.
Perform the pressure sensor calibration.
Perform the system test.
14
Document no. M1031518-02
Planned maintenance check list
5.
Perform the gas calibration.
6.
Connect the catheter to the module. Start measurement by pressing the Start-Stop key on the
module. Check that the catheter fills up.
Stop the measurement by pressing the Start-Stop key. Check that Meas. Off text appears in
the digit field.
"
2.2.9
Multiparameter Hemodynamic Modules
ECG and RESP measurements
1.
Enter the ESTP: ECG service menu.
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the ECG/RESP board memories have passed the internal
memory test, i.e. RAM, ROM and EEPROM all state OK.
2.
3.
Check the front panel membrane key ECG LEAD, if available.
Check that the ‘Power Freq’ value is set according to the mains power frequency. Correct the
setting, if necessary.
Connect a 3-lead ECG trunk cable without a lead set to the module. Check that the message
'Leads off' is displayed on the screen.
Connect a 12-lead ECG trunk cable without a lead set to the module. Check that the message
'Leads off' is displayed on the screen.
Modules without the 12-lead capability (M-ESTPR, M-ETPR, M-ESTR, M-NESTPR, M-NETPR and
M-NESTR modules): connect a 5-lead ECG cable to the module. Connect the cable leads to a
patient simulator.
Check that the ‘Cable type’ shows 5 lead.
Disconnect one of the leads and check that the corresponding electrode in the service menu
shows OFF within 10 seconds from the disconnection, then reconnect the lead.
Check the rest of the leads using the same method.
NOTE: With NESTPR/ESTPR type modules: when the ground lead (black) is disconnected, all the
electrodes should show OFF. With M-NE12STPR, M-PRESTN, E-PRESTN and E-PSM: when any
of the limb leads is disconnected, the measurement will automatically change to 3 electrode
ECG measurement.
NOTE: The asystole and different leads off messages are shown using certain priority. Even
though one of the leads is disconnected, the related leads off message may not appear on the
screen.
NOTE: When RA, LA, LL or RL electrode is disconnected, all V electrodes show OFF.
NOTE: With NESTPR/ESTPR type modules and 5 lead cable, the state of V2, V3, V4, V5 and V6
electrodes follow the state of the V electrode.
Check that all ECG and impedance respiration information is shown on the monitor screen as
configured on the simulator.
Check that the pacer count value in the service menu is shown according to the simulator
configuration.
Change baseline impedance on the simulator and check that appropriate RESP waveform and
RR values are shown again within 30 seconds.
4.
5.
6.
7.
15
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Turn the simulator off. Check that the ‘Asystole’ and ‘Apnea’ messages are displayed.
"
Temperature measurement
8.
9.
Enter the ESTP: STP service menu.
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the STP board memories have passed the internal memory
test, i.e. RAM, ROM and EEPROM all show OK.
Check the temperature measurement calibration using temperature test plugs.
NOTE: Make sure that the protection for temperature calibration is set on, if calibration is
needed.
"
Invasive blood pressure measurement
10. Check the function of the module front panel membrane keys.
11. Check the InvBP channels with a patient simulator.
Zero the InvBP channels, then check that the values and waveforms correspond to the simulator
settings.
"
SpO2 measurement
12. Check that the message ‘No probe’ is shown, when no SpO2 sensor is connected.
Connect an SpO2 finger probe to the module. Check that the message ‘Probe off’ is shown,
when the probe is not connected to a finger.
13. Attach the SpO2 probe to your finger. Check that a reading of 95-99 and a pleth waveform
appear on the screen.
"
Non invasive blood pressure measurement
14. Enter the NIBP module service menu.
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the NIBP board memories have passed the internal memory
test, i.e. RAM, ROM and EEPROM all show OK.
15. Check the function of the front panel membrane keys.
16. Check the NIBP tubing system for leakages by performing Calibrations - Active leak test.
17. Perform NIBP calibration by selecting Calibration.
18. Enter the Pneumatics service menu.
Check the NIBP watchdog timer activation pressure with a pressure manometer.
19. For Modules M-ESTPR and M-NE(12)STPR: Check the NIBP watchdog timer by performing
Watchdog – Test Adult and Test Infant.
20. Check the safety valve by performing Safety Valve – Adult and Infant.
16
Document no. M1031518-02
Planned maintenance check list
21. Attach an adult NIBP hose and cuff onto your arm and perform one NIBP measurement. Check
that the module identifies the cuff, i.e. the text ‘Adult’ appears in the NIBP digit field for a short
time.
Check that the module gives a reasonable measurement result.
E-PSM(P), E-PRESTN:
22. Attach a NIBP cuff hose without cuff identification and check that the module identifies the
hose:
−
The message ‘Select inflation limits’ appears in the NIBP digit field.
−
When you try to start the measurement, the monitor automatically opens the selections
NIBP Setup - Inflation Limits.
"
2.2.10 EEG Module, E-EEG/ M-EEG and EEG Headbox, N-EEG
1.
Enter the EEG & EP service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values in the module view are
not increasing faster than by 5 per second. Check that the memories of the module have
passed the internal memory test, i.e. RAM, ROM and EEPROM all state OK.
Check that the HB Mod Time-outs, HB Mod Bad Checksum and Mod HB Bad Checksum values
are not increasing faster than by 5 per second. Check that the memory of the headbox has
passed the internal memory test, i.e. HB Rom Error in the headbox view states 0.
2.
Check the EP Start/Stop and Imp. Check membrane keys both in the module and the
headbox.
Connect the EEG simulator to the headbox. Select 10 kΩ as imped. pos. and imped. neg. value
on the simulator. Go to EEG & EP service menu and select Check Electr. Check in the headbox
view that the impedances in all four channels are 10 kΩ ±1 kΩ.
Select 2 kΩ as imped. pos. and imped. neg. value on the simulator. Select 10 Hz 200 µV
sinewave on the simulator and check that all the four waveforms have the same form. Check
that the size of the waveforms is 200 µVpp ±5 V. Check that the MF value is 10 ±0.5 Hz. Check
that the amp value is 71 µV ±3 µV.
Plug in the earphones to the headbox.
NOTE: Be careful with loud stimulation from the earphones when starting AEP stimulation.
3.
4.
5.
Start AEP stimulation by pressing the EP Start/Stop button on the module. Check that the
clicking sound comes from the earphones in 1.1 Hz frequency. Stop the stimulation by pressing
again the EP Start/Stop button on the module. Check that the clicking stopped.
"
2.2.11 BIS Module, E-BIS/ M-BIS
1.
Enter the BIS service menu:
Check that the DSC is connected to the module and the PIC+ cable is connected to the DSC.
Check that the Mod Mon Time-outs, Mon Mod Bad checksums, Mod Mon Bad Checksums and
Bad Checksums from BIS values in the module view are not increasing faster than by 5 per
second.
17
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Check that the memories of the module have passed the internal memory test, i.e. RAM, ROM
and EEPROM all state OK.
2.
3.
4.
5.
6.
Check the BIS and Sensor Check membrane keys of the module. Stay in the module view and
press each key for at least one second and check that the key being pressed is identified, i.e.
the corresponding 'PUSHED' text appears in the service menu.
Check that ‘Messages from BE’ are increasing steadily.
Enter the Sensor menu.
Check that
- sensor type indicates 'No Sensor' (i.e. no sensor is identified)
- no sensor is identified
- mains frequency is set correctly
- check that ‘BE powerup test’, ‘DSC selftest Ch1’ and ‘DSC selftest Ch2’ all show 'PASSED'
(if not, go to BIS Setup menu, perform DSC Test and check the results again)
Connect the BIS simulator to the PIC+ cable. See that ‘Checking sensor’ text and image appear
in the waveform numeric field. Wait for a while and check that all sensors show 'PASS'. Check
that the ‘Sensor type’ shows correct information.
Check that the ‘BIS’, ‘SQI’ and ‘SR’ values are between 0...1000, and the ‘EMG’ value between
0...10000.
NOTE: If Sensor Simulator 900508 is used, the values can be out of the given range.
Enter the Module menu.
Check that no BIS engine errors appear.
Perform sensor check by pressing Check Sensor and see that the check is passed.
During the sensor check the Impedance meas. should show 'CYCLIC'. During operation the
Impedance meas. should show 'COMBINED' or 'OFF' (depending on the user setting in BIS
Setup menu).
"
2.2.12 Entropy Module, E-ENTROPY/ M-ENTROPY
1.
Enter the Entropy service menu.
Check that the Entropy sensor cable is connected to the module.
Check that the Time-outs, Bad checksums and Bad c-s by mod values in the module view are
not increasing faster than by 5 per second. Check that the memories of the module have
passed the internal memory test, i.e. RAM, ROM and EEPROM all state OK.
2.
Check the Entropy and Check Sensor membrane keys of the module. Stay in the module
view and press each key for at least one second and check that the key being pressed is
identified, i.e. the Check Sensor text is highlighted in the service menu and that pressing the
Entropy key brings up the Entropy menu.
Connect the Entropy simulator (N-ES) to the cable. See that the ‘Checking sensor’ text and
image appear in the waveform numeric field. Wait for a while and check that all sensors show
“PASS”.
Check that the EntrEEG waveform and RE and SE values appear on the monitor screen.
3.
4.
"
18
Document no. M1031518-02
Planned maintenance check list
2.2.13 Pressure/Pressure Temp Modules, E-P, E-PT, M-P, M-PT
1.
Enter the P/PT module service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the PT board memories have passed the internal memory test,
i.e. RAM, ROM and EEPROM all show OK.
"
Invasive blood pressure measurement
2.
3.
Check the function of the front panel Zero P3 membrane key.
Check the InvBP channel with a patient simulator.
Zero the InvBP channel. Then check that the values and waveforms correspond to the simulator
settings.
"
Modules w/ temperature measurement
4.
Check the temperature measurement calibration using temperature test plugs.
NOTE: Make sure that the protection for temperature calibration is set on.
"
2.2.14 Dual pressure Module, E-PP, M-PP
1.
Enter the PP module service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the Dual Pressure module, E-PP or M-PP, memories have
passed the internal memory test, i.e. RAM, ROM and EEPROM all show OK.
2.
3.
Check the function of the front panel Zero P5 and Zero P6 membrane keys.
Check the InvBP channels with a patient simulator.
Zero the InvBP channels. Then check that the values and waveforms correspond to the
simulator settings.
"
2.2.15 Cardiac Output Modules, E-COP, E-COPSv, M-COP, M-COPSv
1.
Enter the COP module service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the module’s memories have passed the internal memory
test, i.e. RAM, ROM and EEPROM all show OK.
"
Invasive blood pressure measurement
2.
Check the function of the front panel membrane Zero P4 key.
19
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.
Check the InvBP channel with a patient simulator.
Zero the InvBP channel. Then check that the values and waveforms correspond to the simulator
settings.
"
SvO2 measurement
4.
5.
Check that the SvO2 values Meas. state, OM fail and OM temp. in the COP module service menu
all show NO OM.
Checks with the SvO2 simulator:
Turn the SvO2 simulator pulsation switch to Medium and the range switch to Normal pulse.
Connect the simulator to the module and check that the following messages appear in the digit
field for SvO2:
6.
Initializing, please wait > Warming up > Not calibrated
Check that ‘Meas. state’ has changed to NORMAL and ‘OM fail’ and ‘OM temp.’ show OK.
NOTE: The ‘OM temp.’ may show UNSTABLE at first, but the message should change to OK
within a half a minute.
Perform an In Vitro calibration with the SvO2 simulator.
Check that the calibration date for In Vitro calibration was updated correctly and the SvO2
reading on the screen is 81% (±2%).
"
Cardiac Output measurement
7.
Enter the COP module service menu.
8.
Check the front panel Start C.O. membrane key.
Enter the C.O. View menu:
Others - C.O. View
9.
Connect a catheter connecting cable to the module connector C.O.
If the module contains a C.O. Test connector (M-COP), attach the catheter connector of the
connecting cable to the C.O. Test connector. Check that the message ‘Cable OK’ appears in the
menu after the self-test.
No Catheter > Self Test in Progress > Cable OK
Check the C.O. measurement with a patient simulator.
"
2.2.16 NIBP module, M-NIBP
1.
2.
Enter the NIBP service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the NIBP board memories have passed the internal memory
test, i.e. RAM, ROM and EEPROM all show OK.
Check the front panel LEDs and membrane keys using the Buttons/Leds service menu.
20
Document no. M1031518-02
Planned maintenance check list
3.
4.
5.
6.
7.
8.
Check the NIBP tubing system for leakages by performing Active leak test.
Perform NIBP calibration by selecting Calibration.
Enter the Pneumatics service menu.
Check the NIBP watchdog timer activation pressure with a pressure manometer.
Check the NIBP watchdog timer by performing Watchdog – Test Adult and Test Infant.
Check the safety valve by performing Safety Valve – Adult and Infant.
Attach an adult NIBP cuff onto your arm and perform one NIBP measurement. Check the
module identifies the cuff, i.e. the text ‘Adult’ appears in the NIBP digit field for a short time.
Check that the module gives a reasonable measurement result.
"
2.2.17 NeuroMuscular Module, E-NMT, M-NMT
1.
Enter the NMT module service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the module’s memories have passed the internal memory
test, i.e. RAM, ROM and EEPROM all state OK.
2.
3.
Check the function of the front panel membrane keys Start-Up and Stop/Continue.
Check that the message ‘Cable off’ is shown in the digit field and that ‘Cable’ on the service
menu states OFF.
Plug the NMT Sensor Cable with the NMT ElectroSensor into the front panel connector NMT.
Check that the message in the digit field changes to ‘Measurement OFF’ and ‘Cable’ in the
service menu states EMG and ELECTR. OFF.
Place a 3 kΩ resistor between the ElectroSensor’s stimulus electrode leads (brown and white).
Perform Start Curr. Test.
Check that the test was successful, i.e. the ‘Current test (mA):’ in the menu states 30 OK, 50 OK
and 70 OK.
Connect the ElectroSensor leads to the NMT simulator. Set the switch on the simulator to FADE
OFF and turn the knob to MAX. Check that ‘Cable’ in the service menu states now only EMG.
4.
5.
6.
7.
Start the NMT measurement (TOF) by pressing the START-UP key on the module.
Check that the found supramaximal current is less than 70 mA, i.e. the ‘Current set’ value in the
service menu is less than 700.
Check that the digit field TOF% value is within 95-105, Count is 4 and T1% is within 95-105.
Check that the Noise value in the service menu remains under 100.
"
2.2.18 Nellcor Compatible Saturation module, E-NSAT, M-NSAT
1.
Enter the M-SAT service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the NSAT module’s ROM memory has passed the internal
memory test, i.e. ROM shows OK.
Check that all three error indicators, Preamp Error, QUART Error and I/O Error state NO.
21
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.
3.
4.
Check that the SpO2 probe related status information in the menu is correct. Only the ‘NoProbe’
should be active (1), when no probe is connected.
Connect a Nellcor SpO2 finger probe to the module. Check that the message ‘Pulse search’ is
shown and the corresponding status information in the menu is active. Check that the shown
message changes to ‘Check probe’ within 30 seconds.
Attach the SpO2 probe on your finger. Check that a reading of 95-100 and a proper SpO2
waveform appear.
"
2.2.19 Datex-Ohmeda Oxygen Saturation module, M-OSAT
1.
2.
3.
4.
Enter the M-SAT service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check also that the module’s ROM memory has passed the internal
memory test, i.e. the ROM shows OK.
Check that the message ‘No probe’ is displayed on the screen when no probe is connected.
Connect a suitable SpO2 finger probe to the module. Check that the message ‘Check probe’ is
displayed on the screen within 30 seconds.
Attach the SpO2 probe on your finger. Check that a reading of 95-100 and a proper SpO2
waveform appear.
"
2.2.20 Memory
1.
2.
3.
4.
Enter the MemCards service menu:
Check that the memory unit is recognized properly, i.e. Present and Active state YES.
Check that the memories and the PCMCIA controller have passed the tests. The status for each
should be OK.
Select Communication.
Check that the Interface status states Active continuously and the error counter values on the
bottom part of the menu are stable.
Select Status.
Insert Data card into the slot.
Wait until the information is fully updated in the service menu, then check that the Card types
are correct and the ‘File system’ states ATA.
Check that the rest of the information is reliable and no errors have been detected.
"
2.2.21 Recorder
1.
Open the paper compartment cover. Check that the message ‘Recorder: Cover open’ appears
on the screen, then close the cover.
22
Document no. M1031518-02
Planned maintenance check list
2.
3.
Press the Record Wave key and check that the module starts recording the selected
waveforms. Press the Stop key again to stop recording.
Check that the quality of the recordings is acceptable.
"
2.2.22 Network Option
1.
2.
Check that the Mon-Net cable connector and the Identification plug are clean and intact, then
connect them to the frame unit. Check that the monitor connects to the Datex-Ohmeda
Network, i.e. the network symbol appears on the upper right-hand corner of the screen. Also a
message regarding the connected Central should appear in the message field on the screen.
NOTE: If necessary, reselect the monitor’s network communication according to the used
network software in the Network service menu.
Enter the Ethernet service menu:
Check that the counters for data errors (CRC, Frame, Transm.) are stable.
Check that the counters for hardware errors (Intern., Missed, FIFO, Overrun) all show 0.
"
2.2.23 Wireless Network Option
1.
2.
Check that the green LED on the wireless antenna card blinks and the WLAN signal strenght
symbol scrolls between zero and full or stays fixed on the monitor screen.
Check that the wireless LAN network symbol appears on the upper right-hand corner of the
screen when the monitor connects to the Datex-Ohmeda Network,
NOTE: If the monitor does not connect to the Datex-Ohmeda Network, check the WLAN configuration
on the monitor and on the network.
"
2.2.24 Interface Module, E-INT, M-INT
1.
Enter the Interface service menu:
Check that the Time-outs, Bad checksums and Bad c-s by mod values are not increasing faster
than by 5 per second. Check that the memories have passed the internal memory test, i.e. RAM
and ROM state OK.
"
2.2.25 Device Interfacing Solution, N-DISxxx
1.
Enter the DIS Interfacing service menu:
Check that the DIS module ‘tout’ and ‘cse’ values do not increase faster than by 5 per second.
Check also that the DIS module memories have passed the internal memory test, i.e. Ram, Rom
and EEPROM state all OK.
23
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Perform the same check for all connected DIS modules.
"
2.2.26 General
1.
Storing trend data
Check that the monitor is capable of storing the trend information and temporary settings in a
short (max. 15 minutes) standby situation with no power cord.
"
2.
Service reset
Check the Service Reset switch. Switch the monitor to standby and press the Service Reset
switch for at least five seconds. Switch the monitor back on and check that the monitor
performs a Cold Start, i.e. all trend information is cleared.
"
3.
Watchdog
Enter the Set/Test service menu and perform Watchdog.
Check that the monitor restarts.
"
4.
Service Log reset
Enter the Service Log service menu.
Clear the content of the Service Log by selecting Reset Log from the menu.
"
5.
Electrical safety check
Perform an Electrical safety check and a leakage current test.
Check that the monitor and all connected units function normally after the performed test.
"
6.
Final cleaning
Switch the monitor to standby and perform final cleaning.
Fill in all necessary documents.
"
24
Document no. M1031518-02
Appendix A, Planned maintenance check form, S/5 Compact Monitors
APPENDIX A Planned maintenance check form,
S/5 Compact Monitors
Customer
Service
Service engineer
Date
Monitor Installation
Frame: F-CM________
System options:
E/M-
Software:
N-
E/M-
K-
N-
E/M-
K-
N-
E/M-
OK = Test OK
N.A. = Test not applicable
Visual Inspection
Fail = Test failed
OK
N.A.
Fail
2.1.1. General
2.1.2. Compact Airway Module, E-CXXXXX/ M-CXXXXX
S/N
2.1.3. Single-width Airway Module, E-miniC/ M-miniC
S/N
2.1.4. Tonometry Module, E-TONO/ M-TONO
S/N
2.1.5. Recorder Unit
S/N
2.1.6. Modules with NIBP measurement
S/N
S/N
Notes
A-1
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Functional Inspection
2.2.1. General
2.2.2. Display
2.2.3. Keyboard(s)
2.2.4. Display Unit
2.2.5. Frame Unit
Notes
2.2.6. Compact Airway Module, E-CXXXXX/ M-CXXXXX
. Anesthesia Agent
. Patient Spirometry
. General
Notes
2.2.7. Single-width Airway Module, E-miniC/ M-miniC
Notes
2.2.8. Tonometry Module, E-TONO/ M-TONO
Notes
2.2.9. Multiparameter Hemodynamic Modules
. ECG and RESP measurements
. Temperature measurement
. Invasive blood pressure measurement
. SpO2 measurement
. Non invasive blood pressure measurement
. E-PSM(P), E-PRESTN:
Notes
A-2
Document no. M1031518-02
OK
N.A.
Fail
Appendix A, Planned maintenance check form, S/5 Compact Monitors
Functional Inspection
OK
N.A.
Fail
2.2.10. EEG Module, E-EEG/ M-EEG and EEG Headbox,
N-EEG
2.2.11. BIS Module, E-BIS/ M-BIS
2.2.12. Entropy Module, E-ENTROPY/ M-ENTROPY
Notes
2.2.13. Pressure/Pressure Temp Modules, E-P, E-PT,
M-P, M-PT
. Invasive blood pressure measurement
. Modules w/ temperature measurement
Notes
2.2.14. Dual pressure Module, E-PP, M-PP
Notes
2.2.15. Cardiac Output Modules, E-COP, E-COPSv,
M-COP, M-COPSv
. Invasive blood pressure measurement
. SvO2 measurement
. Cardiac Output measurement
Notes
2.2.16. NIBP module, M-NIBP
S/N
2.2.17. NeuroMuscular Module, E-NMT, M-NMT
S/N
2.2.18. Nellcor Compatible Saturation module, E-NSAT,
M-NSAT
S/N
2.2.19. Datex-Ohmeda Oxygen Saturation module,
M-OSAT
S/N
2.2.20. Memory
S/N
2.2.21. Recorder
S/N
2.2.22. Network Option
S/N
A-3
Document no. M1031518-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Functional Inspection
OK
2.2.24. Interface Module, E-INT, M-INT
S/N
2.2.25. Device Interfacing Solution, N-DISxxx
S/N
S/N
S/N
S/N
Notes
2.2.26. General
1. Storing trend data
2. Service reset
3. Watchdog
4. Service Log reset
5. Electrical safety check
6. Final cleaning
Notes
Used spare parts
Notes
Signature
A-4
Document no. M1031518-02
N.A.
Fail
Datex-Ohmeda
S/5TM Compact Anesthesia Monitor
S/5TM Compact Critical Care Monitor
Monitor Software L-CANE05(A) and L-CICU05(A)
Service Menu
All specifications are subject to change without notice.
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
Document no. M1031519-01
March, 2006
Datex-Ohmeda Inc.
P.O. Box 7550
Madison, WI 53707-7550, USA
Tel: +1 608 221 1551
Fax: +1 608 222 9147
GE Healthcare Finland Oy
Helsinki, Finland
P.O. Box 900
FI-00031 GE, FINLAND
Tel: +358 10 39411
Fax: +358 9 1463310
www.gehealthcare.com
Copyright  2006 General Electric Company
Table of contents
Table of contents
Table of contents
i
List of tables
iii
Introduction
1
1
Frame
1.1
1.2
1.3
1.4
1.5
3
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2.1
Network Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2.2
Network Config. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2.3
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2.4
WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MemCards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
1.3.1
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
1.3.2
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.4.1
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
PCMCIA Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2
Display
14
3
Keyboard
15
3.1
3.2
4
Keyboard Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Keyboard Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Parameters
4.1
4.2
4.3
4.4
4.5
4.6
4.7
17
Gas Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
4.1.1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
4.1.2
Gases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
4.1.3
Spirometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
ECG Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4.2.1
ECG Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ESTP Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.3.1
Calibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
P/PT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.4.1
P/PT Calibrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
PP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
4.5.1
PP Calibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
COP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4.6.1
COP Calibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
NIBP Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
4.7.1
NIBP Demo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
4.7.2
NIBP Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.7.3
NIBP Safety Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
4.7.4
NIBP Pulse Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.7.5
NIBP Buttons/Leds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
i
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
5
Set/Test
5.1
6
4.7.6
NIBP Pneumatics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
4.7.7
NIBP Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
NMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
4.8.1
NMT Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Oxygen Saturation Modules, E-NSAT, M-NSAT, M-OSAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
More. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Interface module, E-INT, M-INT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
4.11.1 Gases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
4.11.2 Sp02. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
4.11.3 NIBP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
4.11.4 Spirometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
4.11.5 Sv02/C.O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Tonometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
4.12.1 Tonometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
4.12.2 Press Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
4.12.3 System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
4.12.4 CO2 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
4.12.5 Pneumatics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
4.12.6 AD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
EEG & EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
4.13.1 EEG & EP Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
BIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
4.14.1 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
4.14.2 BIS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Entropy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
4.15.1 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
DIS Interfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
4.16.1 Interfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
4.16.2 Status Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
4.16.3 DIS Interfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Country Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Service Log
6.1
6.2
6.3
6.4
75
77
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
6.1.1
Planned Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
6.1.2
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
6.1.3
Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Error History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Event History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Alarm History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
7
Record Data
82
8
Remote Access
83
Appendix A: How to read HEX numbers
ii
Document no. M1031519-01
A-1
List of tables
List of tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Ethernet service data .............................................................................................................. 7
Module general status .......................................................................................................... 50
Module hardware status........................................................................................................ 51
Module keyboard status........................................................................................................ 51
Module general error status................................................................................................... 51
Module pneumatics error status ............................................................................................ 52
Module hardware error status................................................................................................ 53
Description of system test ..................................................................................................... 56
Module general status .......................................................................................................... 65
BIS Engine status.................................................................................................................. 65
BIS Engine and DSC error messages...................................................................................... 65
DSC status ........................................................................................................................... 68
Sensor status ....................................................................................................................... 68
BE power up status ............................................................................................................... 68
HEX to binary conversion...................................................................................................... A-1
iii
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
iv
Document no. M1031519-01
Service Menu
Introduction
The monitor has a Service Menu, which is a useful tool to examine monitor functions and to
troubleshoot in case a fault occurs.
Service Menu structure
Service Menu
Memory
Network
Frame
Network Status
Subnet Status
Network Conf ig
Ethernet
WLAN
MemCards
Sockets
Status
Power Supply
Display
Key board
PCMCIABoard
Battery
Key board Log
Key board Ty pe
Parameters
Communication
General
Gases
Gas Unit
Spirometry
ECGModule
ECGSetup
ESTPModule
Calibrations
P/PT
Calibrations
PP
Calibrations
COP
Calibrations
NIBPModule
NIBPdemo
Calibrations
Saf ety v alv e
Pulsev alv e
Buttons/Leds
Gases
Pneumatics
SpO2
Watchdog
NIBP
Spirometry
NMT setup
M-SAT
More...
Tonometry
Interf ace
TONO
EEG/EP
Set/Test
Country Settings
BIS
ENTROPY
Serv ice Log
RecordData
RemoteAccess
Maintenance
Sv O2/C.O.
DISInterf acing
Error history
PlannedMaint.
Ev ent history
Repair
Alarm history
Upgrade
Press sensor
Sy stem test
CO2 sensor
Pneumatics
AD
EEG/EPsetup
BISsetup
servmenu_struct03_CAM.vsd
NMT
1
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Service Menu
NOTE: The Service Menu pictures are for reference only. Details on the menu page can vary depending
on the software version and the module type in use.
1. Press the Monitor Setup key.
2. Select Install/Service (password
16-4-34).
3. Select Service (password 26-23-8).
2
Document no. M1031519-01
Service Menu
1
Frame
The frame menu includes service menus common
for the frame.
1.1
Memory
A service menu to check the status of the memory
used in the CPU board of the monitor.
Test Memory tests the condition of the
EEPROM/Flash memory component of the CPU
board. If the result of the test is Fail, see section
“Error messages” in the Display unit slot.
Test SRAM tests the Static RAM memory of the CPU
board in a similar way as the EEPROM/Flash
memory. If the result of the test is Fail, see section
“Error messages” in the Display unit slot.
Real-time clock test is run at every start up and
also during the operation of the monitor. If the
result of the test is Fail, the battery for the SRAM
timekeeper should be replaced.
3
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.2
1.2.1
Network
Network Status
The Network Status view shows the general status
of the network
Location ID: Monitor’s location given at the
setup.
DRI level: Shows the selected level of network
communication. The network communication is
set according to the network software used (e.g.
S-CNET01)
Interfaces: The field indicates if there is a
connection to the Datex-Ohmeda Network
Gateway Interface: The field indicates the active
network interface (None/Ethernet/WLAN)
Connections: Names of subnet id:s connected
The field represents the subnet status menus, i.e.
shows the connected subnets. The three first connections are reserved permanently for Datex-Ohmeda Central, and the fourth is reserved for
another subnet, e.g. Datex-Ohmeda S/5 Arrhythmia Workstation.
4
Document no. M1031519-01
Service Menu
Subnet Status
The Subnet status view gives more accurate
information of the different subnet id:s connected. All
four Subnet status menus have a similar structure.
The number of different packets transmitted and
received by the monitor are shown in the columns
below Tx and Rx. The packet types are:
Waveforms: Waveform data
Phys. data: Physiological numerical data
Alarms:
Alarms, alarm profiles and alarm
limits
Link mgmt: Network management messages
Record K:
Record Keeper data
MonToMon: Monitor-to-monitor communication
related data
Printer:
Printing data and control messages
File Op.:
File operation messages, saving and
loading of cases
Service:
Maintenance and service
Modes:
User mode data
Indics.:
Remote indications sent to monitor
RemoteEv:
Remote events
Data server: Packets of the data server (Arrhythmia
Workstation)
Packets total: Total number of packets
sent/received
Bytes total: Total number of bytes sent/received
T-o
Number or resendings
InE
Received faulty packets
LenE
Erroneous packet length
Dupl
Same packet received as a duplicate
5
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.2.2
Network Config
The DRI Level is for setting the monitor's network
communication. The network communication is set
according to the network software used (e.g.
S-CNET01).
Network software S-CNET01 ->DRI Level = 2001
Network software S-CNET02 ->DRI Level = 2001 or
2002(WLAN)
Network software L-NET03 ->DRI Level = 2003
Virtual Plug ID indicates the monitor’s location
(Network ID). Virtual Plug ID is automatically
defined when downloading the WLAN option to the
monitor.
1.2.3
Ethernet
The Ethernet Status view shows the general
status of the ethernet network communication.
Driver: Ethernet chip name (DP83902, DP83907)
Cable: Indicates if the ethernet cable is
connected.
EthernetAddr: Monitor’s ethernet address.
Speed: Indicates the current ethernet
communication speed.
The service data related to the ethernet status view
is described in the following table.
6
Document no. M1031519-01
Service Menu
Table 1
Ethernet service data
Value
Usage
Notes
Received packets (Statistics
In/Packets)
Total number of received packets since last
cold start.
Transmitted packets (Statistics
Out/Packets)
Total number of transmitted packets since
last cold start.
Received bytes (Statistics In/Bytes)
Total number of received bytes since last
cold start.
Transmitted bytes (Statistics
In/Bytes)
Total number of transmitted bytes since
last cold start.
CRC errors (CRC)
Number of received packets with incorrect
checksum.
Frame errors (Frame)
Number of received packets with incorrect Refers to physical layer problems.
frame structure.
An erroneous packet often has
both frame and CRC error.
Transmission errors (Transm.)
Number or errors in packet Transmission.
Internal errors (Intern.)
Internal error of the network board.
Must always be 0.
Missed packets (Missed)
Number of received packets lost due to
overload.
Must always be 0.
FIFO errors (FIFO)
Internal error of the network board.
Must always be 0.
Overrun errors (Overrun)
Practically same as above.
Must always be 0.
7
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.2.4
WLAN
Driver: WLAN driver chip name.
Connection indicates the state of the WLAN
connection.
Ethernet Addr: Ethernet address of the WLAN card
used.
AP MAC: Ethernet address of the access point where
the monitor is currently connected.
Signal Quality indicates the quality of the radio signal
between the monitor and the access point (0…100%).
Channel is the WLAN channel configured to the
access point where the monitor is currently
connected.
Speed indicates the current communication speed
with the access point.
RoamCounter Occurred roamings between access
points.
Reset Counter *
Network ID: Identifies the WLAN network used.
Firmware version: *
Firmware date: *
Statistics (Packets, Bytes, Errors, Fails, Buffer)
shows the WLAN communication related statistics.
* WLAN PCMCIA card related information
8
Document no. M1031519-01
Service Menu
AP List
Access Points: shows the access points (max. eight)
which are visible for the monitor.
CH is the WLAN channel configured to this particular
access point.
NL indicates the noise level of the channel used
(0…100%)
SL indicates the signal level of the channel used
(0…100%)
WLAN Config
Network ID is for setting the correct WLAN network
ID name.
WEP Algorithm is for setting the level of the
encryption (width of encryption key) used for WLAN
security (40 bit or 128 bit).
Key ID is for choosing the encryption key used.
Encryption key is for setting the encryption key.
NOTE: When selecting 40 bit encryption, enter 10
Hex digit characters (divided into 2 fields).
When selecting 128 bit encryption, enter 26 Hex digit
characters (divided into 2 fields).
NOTE: Use only hexadecimal characters.
NOTE: For all the monitors and access points in the
same WLAN network, the previous parameters must
be set to be the same.
9
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.3
1.3.1
MemCards
Status
Module Present indicates whether the MemCard option
is installed into the monitor. Possible values are YES and
NO.
Module Active indicates whether the MemCard services
are available. Possible values are YES and NO.
ROM indicates the status of the ROM memory of the
module. Possible values are OK and ERR.
RAM indicates the status of the RAM memory of the
module. Possible values are OK and ERR.
PCMCIA indicates the status of the PCMCIA controller of
the module. Possible values are OK and ERR.
EEPROM indicates the status of the EEPROM memory of
the module. Possible values are OK and ERR.
SLOT1 and SLOT2 indicate the left hand slot and the right hand slot, respectively.
Card type
indicates whether the card is MENU or DATA card. If a duplicated card is inserted, type DUPL.
File system
indicates the type of the memory card in use. The only supported file system is ATA. If a memory
card using another file system is used, the message ‘UNKNOWN’ is shown. If the card is poorly
attached, the message ‘LOOSE’ is shown.
Card size
indicates the total amount of disk space in the card in kilobytes.
Card used
indicates the total amount of used disk space in the card in kilobytes.
Card full
indicates whether all the disk space in the card is used. Possible values are YES and NO.
Card empty
indicates the lack of menu files in the MENU card or no files in the DATA card. Possible values are
YES and NO.
Read error
indicates whether the reading from the card has failed. Possible values are YES and NO.
Write error
indicates whether the writing to the card has failed. Possible values are YES and NO.
All values can be '- - -' to indicate 'No data available'.
10
Document no. M1031519-01
Service Menu
1.3.2
Communication
Interface status indicates the status of the data link
between the CPU and MEM sections. If the MemCard
option is installed, the status should always be on
ACTIVE. If the status blinks between ACTIVE and CLOSED,
a communications error has occurred.
Message types indicates the type of data packets that
have been sent (Tx) and received (Rx) since last monitor
start. Data types are listed on the lines below Message
types text.
Data types:
Record K
File Operation
Service
Modes
Module status
Packets total
Bytes total
indicates the communication between
the Monitor and Record Keeper.
indicates the operations of Patient data.
indicates the MEM section operations.
indicates the User Mode operations.
indicates the number of sent/received data packets that relate to the MEM section status.
indicates the total amount of data packets that have been sent/received since the last monitor
start.
indicates the total amount of data bytes that have been sent/received since the last monitor start.
The last four lines indicate transmission errors:
Timeouts
Chksum err
Length err
Duplicated
indicates the number of timeouts that have occurred in MEM section data transmission since the
last monitor start.
indicates the number of checksum errors in data packets from MEM section since the last monitor
start.
indicates the number of data packets with erroneous length from the MEM section since the last
monitor start.
indicates the number of duplicate data packets from the MEM section since the last monitor start.
11
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1.4
Power supply
The menu shows the voltages and the temperature
measured by the power management board (PMB
Voltages) and the main CPU board in the Display
unit(DU Voltages). The measurement starts about
100 ms after a start-up. The values in the column
under Mean are the mean values of the last one
second, the Min column shows the minimum mean
value, and the Max column the maximum mean
value of the voltages and temperature measured
during the current power ON.
The following voltages are measured by the PMB in
the Frame Unit:
Raw DC
+15V
14.65….15.35
–15V
-14.65...-15.35 V
+15VD
14.65...16.00 V
+5V
4.85...5.25 V
Temp (°C) value corresponds with the Frame Unit
internal temperature measured by the PMB.
The numbers on this page are only directive and not absolute values.
The following voltages are measured by the Central Processing Board in the Display Unit:
+12V
11.50…12.50V
+3.3V
3.00…3.60V
VBUS
10.00…17.00V
Temp (°C) value corresponds with the Display Unit internal temperature measured by the Central Processing
Board.
MPS input current is the current fed to the Module Power Supply. The current should be <4A.
AC/DC capacity in use is the capacity information achieved from the AC/DC unit by the PMB.
AC/DC voltage is the AC/DC power unit output voltage measured by the PMB.
12
Document no. M1031519-01
Service Menu
1.4.1
Battery
Select Battery: Selection of battery type.
Capacity: Selection of battery capacity.
Previous Menu: Return to the previous menu.
Service Data
Type shows the type of the battery used.
Capacity refers to battery capacity in Ah.
Left [%]: Evaluated capacity left in battery.
Temperature [°C] measured inside the battery.
Current [A] shows the charging state and charging
current.
Voltage [V] (Full, Timed, Fast) shows the measured
battery voltage.
Monitor Temperature shows the Frame Unit inside
temperature measured by the PMB.
1.5
PCMCIA Board
Chip type is the type of the PCMCIA controller chip
used.
Number of slots is the number of PCMCIA card
slots in use (0, 1 or 2).
Slot A/B State and Drv Active indicate if the
PCMCIA card slot is active.
Driver Ptr, Detect Int and PcCard Int: PCMCIA
card driver software related data.
PcCard info: General PCMCIA card related
information.
13
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2
Display
Geometry views the geometry of the display.
Colors views the color of the screen.
Readability views the readability of the screen.
14
Document no. M1031519-01
Service Menu
3
Keyboard
Keyboard
The service menu for testing the command board
functions.
Upper Led is for testing the upper alarm LED (red) on the
command board. When the text is highlighted, the upper
alarm LED can be turned on and off by pressing the
ComWheel.
Lower Led is for testing the lower alarm LED (yellow) on
the command board. When the text is highlighted, the
lower alarm LED can be turned on and off by pressing the
ComWheel.
Dummy Press is for testing the ComWheel. When the text
is highlighted, pressing the ComWheel creates a sound
from the loudspeaker and the corresponding number on
the service data field increases.
Service Data
Message count counts the number of messages that are sent out to the main CPU board.
Leds upper and lower indicate the states of the alarm LEDs on the command board.
Direct action keys texts are indications to the command board membrane keys. When a key on the command board
is pressed, the corresponding text in the menu changes its colour.
Control wheel, Press counts the ComWheel pressings.
Control wheel, Clockwise and Counter clockwise indicate the ComWheel turnings.
Since shows the date and the time of the last run time reset.
15
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.1
Keyboard Log
Keyboard Scroll Log
All the keyboard presses and the commands given
by the ComWheel are recorded in the Keyboard
Log. The keyboard log is saved in the permanent
memory of the monitor. The length of the log is
1150 events. The log is FIFO type.
Scroll Stat enables to scroll the keyboard events.
3.2
Keyboard Type
Store Mask A selection for the anaesthesia keyboard’s
language. The selected language determines the
outcome of the lower keypad.
Store Type is for selecting the keyboard;
COM = Command Board
ARK = Anaesthesia Keyboard
AIC = Information Center Keyboard
NOTE: The settings should be checked if the controller
board is replaced. If settings are changed, the new
settings will not be valid until the next start-up.
16
Document no. M1031519-01
Service Menu
4
Parameters
NOTE: Parameter values in Service Data fields are only for reference in this section.
4.1
Gas Unit
Service menu for airway gas modules’ communication
and airway gas and spirometry measurements.
17
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.1.1
General
Service Data
Module configuration shows which measurement
options are available, i.e. are detected by the module.
Timeouts is a cumulative number that indicates how
many times the module has not responded to the
monitor's inquiry.
Bad checksums is a cumulative number that indicates
how many times communication from the module to
monitor has broken down.
Bad c-s by mod is a cumulative number that indicates
how many communication errors the module has
detected.
The monitor starts counting these items at power up and
resets to zero at power off. The values may also be reset
when a module is attached to the monitor frame and be
set to 32769 or continuous counting may be started when
the module is removed from the monitor frame.
The nonzero values do not indicate a failure, but the continuous counting (more than 5 per second) or value 32769
indicates either a serial communication failure or a module not in place. Also failures in other modules may cause these
numbers to rise or be set to 32769.
18
Document no. M1031519-01
Service Menu
4.1.2
Gases
Noise Meas
activates the noise measurement.
Sample gain adj adjusts the sampling pump gain, i.e.
for adjusting the sample flow
measurement.
Fall time Meas * activates the fall time measurement.
Pump ctrl
A manual control for the sampling
pump.
Zero valve ctrl A manual control for the zero valve.
Occl valve ctrl* A manual control for the occlusion
valve.
Record Data
prints out the shown service data and
board information (id. serial number
and software id.) onto the recorder
module.
Service Data
O2, CO2, N2O, AA
% field shows real-time concentrations.
noise-% is standard deviation of concentration.
O2, CO2, N2O, AA channels A-E
Amb-Work:
Fall time*
mV field: signal is scaled to mV.
Gain: User gain. It is scaled as (User gain)/(Factory gain).
Shows the identified agent.
The shown value tells how unreliable the identification is. With pure agent the value is typically <
75.
is calculated from differential pressure and adjusted by the module. Zero value as measured
during initialization when the pump is off. Gain: sample flow measurement can be calibrated by
adjusting the gain.
Ambient pressure is measured continuously in E-miniC. In M-miniC it is measured at least once an
hour (during the first running hour during each zeroing process). In M-Gas it is measured once an
hour .
ambient pressure - sampling system internal pressure.
CO2 and O2 in ms. For N2O and AA same as CO2.
CO2-O2 Delay*
In ms. No delay between CO2, N2O, and agents.
ID*
ID unrel.*
Sample Flow
Ambient*
Pump
Can be toggled ON/OFF. PWM output 0-100% is shown. Pump voltage is also shown.
Lamp
The state, PWM control, and current of the lamp are shown.
Fan*
The state of the fan is shown.
Zero and Occl valve Can be toggled between the measurement state (MEAS) and zeroing/occlusion states
(ZERO/OCCL).
Temp
Temperatures measured by the module from TPX, CPU, and OM.
Time after power on In minutes after power on.
19
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.1.3
Spirometry
Insp and exp flow gains can be adjusted, if calibration is
needed. A calibration pump or spirometry tester is used
and readings are observed from the display. If a deviation
exists, gains are adjusted accordingly. Gain scaling is
1.000, when the factory settings are in effect (1.050 in
modules that contain the Gas Exchange measurement).
When the Adjust key is pressed, a separate box for
adjusting the value appears. During adjustment
calibration, values are sent to the module. When the
ComWheel is pressed, the values are permanently stored
in EEPROM of the module and the box disappears.
Zero PVX: Start zeroing the pressure sensors. Effects Aw
Pres Zero and Flow Zero value.
Exp Flow Gain / Insp Flow Gain: Adjust the Flow sensor
gains.
Valves: Switch between MEASUREMENT and ZEROING
VCO2 / VO2 Gain: Adjust the VCO2 and VO2 gain.
Y deadspace: Adjust the Y-deadspace.
N2 injection: Select between on (1) and off (0).
Record Data: Record Data prints out the shown service data and board information (id. serial number and software id.)
onto the recorder module.
20
Document no. M1031519-01
Service Menu
Service Data
Sensor ADULT/PEDIATRIC according to the selected measurement mode (sensor).
Insp/Exp Flow Gains shown apply to the selected sensor.
Aw Press Zero and Flow Zero are the result of zeroing in the user service menu. They can be adjusted in the factory
calibration menu, but not permanently stored.
Aw Press Gain is directly the value used in sw. It can be adjusted, but not permanently stored.
Exp Flow and Insp Flow Gains are scaled as (User gain)/(Factory gain). Exp and Insp Flow Gains can be adjusted also
in the user service menu.
Common Offset is the compensation factor for pressure difference reading of the difference sensor when applying an
equal pressure on both sides of the sensor.
Valves can be changed between MEASUREMENT and ZEROING.
Zeroing automatic zeroing either ENABLED or DISABLED (only factory service menu).
Aw Pressure shows the real time value of airway pressure.
Condition shows in which reference conditions the results are. With calibration pump or spirometry tester, the results
are always in ATP. If breathing is detected (EtCO2 > 1.0%), the results are according to the Flow & Vol Setup selection.
Flow shows the flow measurement value.
TVol Exp, TVol Insp, MVol Exp and MVol Insp are shown to ease calibration. The numbers are the same as on the main
display. The former pump calibration procedure has been dropped out. We claim that calibration is not needed in
routine clinical use, so a separate Flow calibration menu is not needed. Calibration can be done with the pump or
spirometry tester. The results must be taken from the screen and gains adjusted accordingly.
VCO2 and VO2 Gain show a value near 1000, the correct gains have been measured in the factory.
Y deadspace is the geometric volume in ml between the Y-piece and the D-lite. Default is 5 ml for a standard Y-piece
(as delivered with Siemens 900C ventilators). Used for VCO2 and VO2 delay time corrections.
Set N2 injection to 1 during laboratory tests with a Spirometry tester and injection of N2 gas (for scientific validations
use only). At power on of the module, the value is always zero.
Ambient pressure value measured by the module.
21
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.2
ECG Module
Power freq: Set power frequency; 50 Hz/60 Hz.
Filter low: Set filter low frequency; 0.05 Hz/0.5 Hz.
Filter high: Set filter high frequency; 30 Hz (40 Hz if power
freq is 60 Hz) /100 Hz or 150 Hz @ NE12STPR.
Service Data
Power freq, and Cable type show the values chosen or
detected, Filter low and high defines the selected filter
(Monitor/Diagnostic/ST).
Quick zero at PRESTN series module is ON when the ECG
signal is beyond the scale, and therefore, is quickly
returned to optimal range using fast signal processing
methods. All the Quick zero bits are ON at the same time.
Cable shows ON when ECG cable is connected.
Electrode shows ON when each of these electrodes are
connected.
Pacer count is a running number for pacemaker users.
Button No effect on the module.
Resp Available indicates that ECG hardware is capable of measuring impedance respiration.
Measurement shows ON when the respiration measurement is on.
Amp zero shows ON when zeroing of the respiration amplifier takes place.
Waveform VALUE will be updated in one second interval.
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor’s
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the
monitor has broken down.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The values may also be reset when
a module is attached to the monitor frame and be set to 32769 or continuous counting may be started when the
module is removed from the monitor frame.
The nonzero values do not indicate a failure, but the continuous counting (more than 5 per second) or value 32769
indicates either a serial communication failure or a module not in place. Also failures in other modules may cause these
numbers to rise or be set to 32769.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum at the EPROM is in accordance with the one the software has calculated.
EEPROM indicates if the values stored in the permanent memory are valid.
The state is either OK, Fail or ? (module not in place or a communication error).
22
Document no. M1031519-01
Service Menu
4.2.1
ECG Setup
Filter filters the ECG signal high frequency noise and
slow respiratory artefacts.
Monit (monitor) filter is used in routine monitoring. It
effectively filters the artefacts caused by the
electrosurgery unit and respiration.
Diagn (diagnostic) filter is used if more accurate
information of the waveform is needed (e.g. of P-wave or
AV block). The diagnostic filter is more susceptible both
to high frequencies and baseline wander than the
monitor filter.
STfilt (ST filter) permits more accurate information of ST
segment. It filters the high frequency artefacts caused by
the electrosurgery unit, but catches the slow changes in
ST segment. The ST filter is more susceptible to baseline
wander than the monitor filter.
5-lead cable selects five or three electrodes. With the
12-lead ECG the selection is automatic.
Pacemaker selects how to display the pacing pulse of cardiac pacemaker. The selections are Show, Hide, ON R and
Sensit.
Hide, the pacing pulse is filtered away from ECG data.
Show, the pacer pulse is filtered away from ECG data but the pulse is displayed as a constant height marker.
ON R, pacing pulses are not filtered away from ECG data. This improves ECG monitoring with A-V pacemaker patients,
as QRS complexes are counted even if the pacing pulse hits the QRS complex. However, during asystole the monitor
may count pacing pulses as heart beats.
Sensit selection uses a more sensitive pacemaker detection. Pacemaker spike is displayed on ECG.
23
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.3
ESTP Module
Service menu for the multiparameter hemodynamic
module’s oxygen saturation, temperature and invasive
pressure measurements.
NOTE: Pressure Module, M-P or E-P, and Pressure
Temperature Module, M-PT or E-PT, have their own
service menu; ”4.4 P/PT.” and so does Dual Pressure
Module, M-PP or E-PP; ”4.5 PP.”
Calibrations opens a submenu for temperature (T1, T2)
and pressure (P1, P2) calibrations. See section
“Calibrations”.
Record Data prints out the shown service data and board
information (id, serial number and sw id) onto the
recorder module.
Temp Test activates the automatic temperature test for
the temperature channels T1 and T2. The result from the
test is shown in the service data field.
NOTE: The Temp Test needs to be selected twice before
the test starts.
Service Data
Gain is a coefficient to compensate gain error. Usually the values for P1 and P2 are between 17000 and 25000 and
for T1 and T2 between 13000 and 14300.
Zero indicates the offset compensation value of each parameter in the A/D converter. Typically the values for P1 and
P2 are within ±1000 and for T1 and T2 between -150 and +300. Calibrate if zero and/or gain value is outside the
ranges.
Cable shows ON when a corresponding cable is connected to the front panel and Probe shows ON when a
corresponding probe is connected to the cable.
Under Value, the measured numeric values are displayed simultaneously. Pressure values are real time values and
shown in mmHg. Temperature values are shown in degrees Celsius.
The front panel STP keys functions are confirmed by pressing each key and observing that OFF turns to ON at Button.
SpO2 shows the measured beat-to-beat SpO2 value.
Modpr is a modulation % that indicates the AC/DC ratio in the measured signal.
Hr is a pulse rate calculated from every beat.
Cable and Probe can be either OFF or ON, and these indicate the state PROBE OFF.
Under them there is a message field for SpO2. It can be OK, PULSE SEARCH, NO PROBE, PROBE OFF, NO PULSE,
ARTEFACT, POOR SIGNAL, or CHECK PROBE.
24
Document no. M1031519-01
Service Menu
Balance between leds is adjusted by changing the intensity of red/infrared. Intensity of infrared (Ired int.) is in the
range of 40 to 255 and red intensity (red int.) is in the range of 40 to 255.
DC gain shows the gain of DC signal adjusted by the module.
IDC is the value of infrared signal.
RDC is the dc value of red signal.
AC gain is the gain of infrared and red ac signals. AC gain values can be 1 or 0. Value 1 means high ac gain and 0
means low gain.
Pre gain is a preamplifier gain for infrared and red signals. Pre gain values can be 1 or 0. Value 1 means normal
operation. Value 0 means that signal levels are very low and extra gain is taken into use.
Temp error shows the status of the temperature test. No errors found show the status (OFF) and errors found (ON).
Protect key shows normally OFF, but turns to ON when the button at the bottom of the module is pressed.
Protect mode is normally ON. It turns to OFF, when Protect is switched to OFF for the temperature calibration in
Calibration Menu.
Configuration shows the chosen module configuration: TP, ST, or STP.
Timeouts is a cumulative number that indicates how many times the module has not responded to the the monitor’s
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the
monitor has broken down.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The values may also be reset
when a module is attached to the monitor frame and be set to 32769 or continuous counting may be started when
the module is removed from the monitor frame.
The nonzero values do not indicate a failure, but the continuous counting (more than 5 per second) or value 32769
indicates either a serial communication failure or a module not in place. Also failures in other modules may cause
these numbers to rise or be set to 32769.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum at the EPROM is in accordance with the one the software has calculated.
EEPROM indicates if the values stored in the permanent memory are valid.
The state is either OK, Fail or ? (module not in place or a communication error).
25
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.3.1
Calibrations
Protection: Protection for the configuration and
temperature calibrations can be set ON and OFF.
Set Config: The module configuration should be set
according to the module type. The setting is possible
only when the protection is set OFF. The available
selections are TP, ST or STP. The configuration setting
should be checked, if the STP board is replaced.
Calibrate T1 / Calibrate T2: The functions are for
calibrating the temperature channels T1 and T2.
Calibrate P1/ Calibrate P2: The functions are for
calibrating the invasive blood pressure channels P1
and P2.
How to calibrate T1/ T2
The calibrations are possible only when the protection is set OFF. The temperature calibration
requires accurate test plugs of value 25 °C and 45 °C.
1. Select Calibrate T1/Calibrate T2.
2. Insert the test plug 25 °C into the T1/T2 connector.
3. Press the ComWheel.
4. Insert the test plug 45 °C into the T1/T2 connector.
5. Press the ComWheel.
How to calibrate P1/ P2
The calibrations require a pressure transducer (with appropriate cable) and a pressure manometer.
1. Connect the pressure transducer with the pressure manometer to the P1/P2 connector. Select
Calibrate P1/Calibrate P2. Leave the transducer to room air pressure.
2. Press the ComWheel to start zeroing.
3. Supply a pressure of 100 mmHg to 300 mmHg to the transducer. The recommended pressure is
200 mmHg.
4. Set the pressure on the display to match the pressure reading on the manometer and press the
ComWheel.
26
Document no. M1031519-01
Service Menu
4.4
P/PT
Service menu for Pressure Module, M-P or E-P, and
Pressure Temperature Module, M-PT or E-PT.
Calibrations: see section “P/PT Calibrations”.
Temp Test activates the automatic temperature test for
the temperature channels T3 and T4. The result from the
test is shown in the service data field.
NOTE: The Temp Test needs to be selected twice before
the test starts.
Record Data: Record Data prints out the shown service
data and board information (id., serial number, and
software id.) onto the recorder.
Service Data
Gain is a coefficient to compensate gain error. Usually
the value for P3 is between 17000 and 25000 and for
T3 and T4 between 13000 and 14300.
Zero indicates the offset compensation value of each
parameter in the A/D converter. Typically the values for
P3 are within ±1000 and for T3 and T4 between -150 and +300. Calibrate if the zero and/or gain value is outside the
ranges.
Cable shows ON when the corresponding cable isconnected to the front panel.
Probe shows ON when the corresponding probe is connected to the cable.
Under Value, the measured numeric values are displayed simultaneously. The pressure value is a real time value and
shown in mmHg.
Button; the front panel key function can be confirmed by pressing the key and checking that OFF turns to ON.
Temp error shows whether the calibration of the temperature was successful or not.
Protect key shows normally OFF but turns to ON when the button at the bottom of the module is pressed.
Protect mode is normally ON. It turns to OFF when Protect is switched to OFF for the temperature calibration in
Calibration Menu.
Configuration shows the chosen module configuration: BP or PT.
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor's
inquiry.
Bad checksums is also a cumulative number that indicates how many times communication from the module to
monitor has broken down.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The values may also be reset when
a module is attached to the monitor frame and be set to 32769 or continuous counting may be started when the
module is removed from the monitor frame.
The nonzero values do not indicate a failure, but the continuous counting (more than 5 per second) or value 32769
indicates either a serial communication failure or a module not in place. Also failures in other modules may cause
these numbers to rise or be set to 32769.
27
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum at the EPROM is in accordance with the one the software has calculated.
EEPROM indicates if the values stored in the permanent memory are valid.
The state is either OK, Fail or ? (module not in place or a communication error).
4.4.1
P/PT Calibrations
Protection for the configuration and temperature
calibrations can be set ON and OFF only when the
protect button at the bottom of the module is pressed.
Set Config: The module configuration should be set
according to the module type. The setting is possible
only when the protection is set OFF. The available
selections are BP or PT.
The configuration setting should be checked, if the PT
board is replaced.
Calibrate T3 and Calibrate T4: The functions are for
calibrating the temperature channels T3 and T4.
Calibrate P3: The function is for calibrating the
invasive blood pressure channel P3.
How to calibrate T3/ T4
The calibrations are possible only when the protection is set OFF. The temperature calibration
requires accurate test plugs of value 25 °C and 45 °C.
1. Select Calibrate T3 / Calibrate T4.
2. Insert the test plug 25 °C into the T3 / T4 connector.
3. Press the ComWheel.
4. Insert the test plug 45 °C into the T3 / T4 connector.
5. Press the ComWheel.
How to calibrate P3
The calibration requires a pressure transducer (with an appropriate cable) and a pressure
manometer.
1. Connect the pressure transducer with the pressure manometer to the P3 connector. Select
Calibrate P3. Leave the transducer to room air pressure.
2. Press the ComWheel to start zeroing.
3. Supply a pressure of 100 mmHg to 300 mmHg to the transducer. The recommended
pressure is 200 mmHg.
4. Set the pressure on the display to match the pressure reading on the manometer and press
the ComWheel.
28
Document no. M1031519-01
Service Menu
4.5
PP
Service menu for Dual Invasive Pressure Module, M-PP
or E-PP.
Calibrations: see section ”PP Calibrations.”
Record Data prints out the service data and circuit
board information (id., serial number, and software id.)
on the recorder.
Service Data
Gain is a coefficient to compensate for gain error.
Usually the values for P5 and P6 are between 17000
and 25000.
Zero indicates the offset compensation value for each
parameter in the A/D converter. Typically the values for
P5 and P6 are within ±1000. Calibrate if the zero and/or
gain value is outside the ranges.
Cable shows ON when the corresponding cable is
connected to the front panel and Probe shows ON when
the corresponding probe is connected to the cable.
Value displays the measured numeric values simultaneously. The pressure value is a real time value and shown in
mmHg.
Button; the front panel key function can be confirmed by pressing the key and checking that OFF turns to ON.
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor's
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the
monitor has failed.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The values may also be reset
when a module is attached to the monitor frame and be set to 32769 or continuous counting may be started when
the module is removed from the monitor frame.
The nonzero values do not indicate a failure, but the continuous counting (more than 5 per second) or value 32769
indicates either a serial communication failure or a module not in place. Also failures in other modules may cause
these numbers to rise or be set to 32769.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum in the EPROM is in accordance with the software calculated value.
EEPROM indicates whether the values stored in the permanent memory are valid. The state is either OK, Fail or ?
(module not in place or a communication error).
29
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.5.1
PP Calibrations
Calibrate P5 and Calibrate P6
These functions are for calibrating the invasive blood
pressure channels P5 and P6.
How to calibrate
The calibrations require a pressure transducer (with an appropriate cable) and a pressure
manometer.
1. Connect the pressure transducer with the pressure manometer to the P5 / P6 connector. Select
Calibrate P5 / Calibrate P6. Leave the transducer at room air pressure.
2. Push the ComWheel to start zeroing.
3. Supply a pressure of 100 mmHg to 300 mmHg to the transducer. The recommended pressure is
200 mmHg.
4. Set the pressure on the display to match the pressure reading on the manometer and push the
ComWheel.
30
Document no. M1031519-01
Service Menu
4.6
COP
Service menu for Cardiac Output Module, M-COP or
E-COP, and Cardiac Output and Mixed Venous Oxygen
saturation (SvO2) Module, M-COPSv or E-COPSv.
Record Data prints out the service data and module
information (id. serial number and software id.) on the
recorder.
Service Data
P4
Gain is a coefficient to compensate for gain error.
Typically the value is between 17000 and 25000.
Calibrate if the zero and/or gain value is outside the
ranges.
Zero indicates the offset compensation value of each
parameter in the A/D converter. Usually the value is
within ±1000.
Cable shows ON when the corresponding cable is
connected to the front panel and Probe shows ON when the corresponding probe is connected to the cable.
Value shows the measured numeric values simultaneously. The pressure value is a real time value and shown in
mmHg.
Probe items Catheter (ON/OFF) and Inj. (FT, BATH, or OFF) indicate connections and Value indicates the measured
temperatures in 0.01 °C increments.
SvO2
Meas. state: Measurement status shows: No optical module (No OM) connected, initializing the optical module (Init
OM), normal measurement state (Normal) and failed module (OM fail).
Value is a measured SvO2 value.
Gain is the gain of the remote red and infrared signals (0, 1, 2 or 3)
Red int: Reflected red intensity
Ired int: Reflected infrared intensity
Loc red: Local red intensity
Loc ired: Local infrared intensity
OM fail: Reason why initialization OK (OK), cannot read EEPROM of the optical module correctly (EEPROM), cannot
adjust LED current to get required local signal (Transmit).
OM temp: Temperature of the optical module OK (OK), temp under 43 °C (Under), temp over 47 °C (Over).
Pulse SQI: Signal quality index for pulsing (low pulse/high pulse). 0 indicates a normal signal, 1 indicates an
intermediate signal, 2 indicates a poor signal, and 3 indicates an unacceptable signal.
Clipp. SQI: Signal quality index for wall artifact. 0 indicates a normal signal, 1 indicates an intermediate signal, 2
indicates a poor signal, and 3 indicates an unacceptable signal.
Int. SQI: Signal quality index for intensity shift from previous calibration or Hgb update (intensity decreased/increased)
0 indicates a normal signal, 1 indicates an intermediate signal, 2 indicates a poor signal, and 3 indicates an
unacceptable signal.
31
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Button: The front panel Zero P4 and Start C.O. key functions can be confirmed by pressing the key and checking that the
relevant OFF message turns to ON.
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor's
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the monitor
has failed.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The values may also be reset when
a module is attached to the monitor frame and be set to 32769 or continuous counting may be started when the
module is removed from the monitor frame.
The nonzero values do not indicate a failure, but the continuous counting (more than 5 per second) or value 32769
indicates either a serial communication failure or a module not in place. Also failures in other modules may cause these
numbers to rise or be set to 32769.
RAM indicates the state of the external RAM memory.
ROM indicates whether the checksum at the EPROM is in accordance with the software calculated value.
EEPROM indicates if the values stored in the permanent memory are valid.
The state is either OK, Fail or ? (module not in place or a communication error).
4.6.1
COP Calibrations
Calibrate P4
This function is for calibrating the invasive blood
pressure channel P4.
How to calibrate
The calibration requires a pressure transducer (with an appropriate cable) and a pressure
manometer.
1. Connect the pressure transducer with the pressure manometer to the P4 connector. Select
Calibrate P4. Leave the transducer at room air pressure.
2. Press the ComWheel to start zeroing.
3. Supply a pressure of 100 mmHg to 300 mmHg to the transducer. The recommended pressure is
200 mmHg.
4. Set the pressure on the display to match the pressure reading on the manometer and press the
ComWheel.
32
Document no. M1031519-01
Service Menu
4.7
NIBP Module
Service menu for Non-invasive Blood Pressure Modules.
Service Data
Pressure shows the measured pressure multiplied by
10. This value is automatically zero-drift compensated.
Zero shows the difference between the zeroing value in
the permanent memory (stored when the module is
calibrated) and the current automatic zero-drift
compensation multiplied by 10. The value can change
between +20 and -20 mmHg. If the zero drift exceeds ±
10 mmHg, the module should be recalibrated.
Protect handle indicates hardware protection for
EEPROM memory. It should be ON all the time in normal
operation. If it is OFF, data cannot be read from or written
to EEPROM, only the calibration protection can be set or
reset by software. It can be turned to OFF by pressing the
NIBP module buttons Auto ON/OFF and Start Cancel
simultaneously for 3 seconds, which also enables
Protection ON/OFF menu selection in the calibration menu.
Calibr. prot. shows software calibration protection and it should be OFF to enable calibration.
+15 V power refers to legacy NIBP modules. Not used in PRESTN series modules and E-PSM(P).
AD0 to AD7 show the values of each eight channels of the A/D converter. AD7 is not used in PRESTN series modules,
M-NIBP module and E-PSM(P).
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor’s
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the
monitor has broken down.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The values may also be reset when
a module is attached to the monitor frame and be set to 32769 or continuous counting may be started when the
module is removed from the monitor frame.
The nonzero values do not indicate a failure, but the continuous counting (more than 5 per second) or value 32769
indicates either a serial communication failure or a module not in place. Also failures in other modules may cause
these numbers to rise or be set to 32769.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum in the EPROM is in accordance with the one the software has calculated.
EEPROM indicates if the values stored in the permanent memory are valid.
The state is either OK, Fail or ? (module not in place or a communication error).
33
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.7.1
NIBP Demo
A service menu for demonstrating the oscillometric
method of NIBP measurement. The menu shows the
real-time pressure signals that are measured from the
NIBP cuff. The measurement result is shown in the
adjoining digit field.
Wave Recording is for selecting the recording option.
If ON is selected, the pressure signals are printed out
in real-time on the recorder.
Remove menu widens the displayed waveform area.
The menu can be closed by selecting the Previous
Menu or just by pressing the ComWheel if the Remove
menu was selected.
34
Document no. M1031519-01
Service Menu
4.7.2
NIBP Calibration
Active Leak Test: Wrap an adult cuff around a pipe
and connect the cuff to the module. Select the active
leak test (ON). The module automatically pumps a
pressure of 260 mmHg into the cuff. Wait for several
seconds until the pressure stabilizes. Then check that
the pressure reading does not drop more than 6 mmHg
per minute. If it does, leaking point(s) should be
detected and fixed. Cancel the test by selecting the
Active leak test OFF.
Calibration Check: After the calibration check is
selected (ON), the module zeroes the pressure
transducers at the beginning of the calibration check.
Do not pump pressure until the text ‘Calibrating’
appears in the NIBP digit field or the zeroing will fail.
After the zeroing is done, manually pump pressure into
the module and make sure that the same pressure
values are shown both on the display and on the
manometer. Pressure of both pressure channels B1
and B2 are shown. The pressure values are automatically zero-compensated, so the readings of B1 and B2 should be
the same as the manometer readings.
Protection: Software calibration protection (ON/OFF). Select OFF when calibrating. Protection selection becomes
available in the menu after pressing the NIBP module buttons Auto ON/OFF and Start/Cancel simultaneously for
3 seconds. For M-NE(12)STPR series modules: Protection can be set ON or OFF only when the toggle switch at the
bottom module is set to the right.
How to Calibrate
Calibration selection is available only when protection is OFF.
NOTE: Both channels B1 and B2 must be calibrated simultaneously.
NOTE: The module must be in the frame during the whole procedure.
NIBP calibration can be performed in the NIBP Service menu as follows:
1.
If Protection is ON, change it to OFF by pressing the NIBP module buttons Auto ON/OFF and
Start Cancel simultaneously for 3 seconds, which enables the Protection selection. Then
press the buttons again for 3 seconds to enable Calibration.
NOTE: When the buttons have been pressed, the NIBP field shows an error message ‘Calibration
switch on!’.
NOTE: For M-NE(12)STPR series modules: If Protection is ON, change it to OFF by first turning the
toggle switch to the right at the bottom of the module, which enables the Protection selection. Then
turn the toggle switch to the left to enable Calibration. When the switch is at the right, the NIBP field
shows an error message ‘Calibration switch on!’
NOTE: When calibration is enabled, a message ‘Calibration not protected’ appears.
2.
For proper zeroing to take place, remove the hose from the front panel connector. Select
Calibration and push the ComWheel. Messages ‘Zeroing’ and ‘Zeroed’ will appear in the NIBP
35
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.
4.
message field. After this, a pressure bar will appear beside the menu and the text ‘Calibrating’
will appear in NIBP digit field.
Connect an external mercury manometer with a pump to the module through the both tubes of
the hose. Pump up to about 200 mmHg pressure (range of 150 to 300 mmHg allowed)
according to the manometer. Verify that both pressure values in the prompt field match the
manometer reading. If not, adjust by turning the ComWheel.
When the values are equal, push the ComWheel to confirm the calibration. After a few seconds
the ‘Calibrated’ message will appear in the NIBP digit field, which means that the calibration
data has now been saved.
NOTE: When calibrating NIBP, always change the displayed pressure value slightly with the
ComWheel, even in cases where the value would be correct. For example, change the value one step
higher and then back one step lower. The ‘Calibrated’ text should appear in the display. This ensures
that the calibration procedure is correctly registered and stored by the module.
5.
4.7.3
Use the module buttons again to enable Protection setting and set it ON, and finally disable
Protection setting.
NIBP Safety Valve
Test: Start test is for starting and Stop test is for
stopping the Safety Valve test.
Safety Valve Data:
For information on general items Pressure, Zero,
Protect handle, Calibr. prot., +15 V power, AD0 to AD7
as well as Timeouts etc., see service data descriptions in
section “4.7 NIBP Module”.
Max. press and 2 s after stop show the measured
values at Safety Valve test.
Safety Valve Test Adult/Infant
Wrap an adult cuff around a pipe and connect the cuff to
the module. Highlight Start test and give the ComWheel
a push. The test ends automatically or when Stop test
(appears in place of Start test) is pushed.
Max. press indicates the pressure at which the safety
valve opens and is normally 300 ±15 mmHg for adult
and 150 mmHg ±15 mmHg for infant.
2 s after stop indicates the pressure at 2 seconds after the pump has stopped and is normally > 270 mmHg for adult
and > 130 mmHg for infant. If the value is less, check leakage by the active leak test.
36
Document no. M1031519-01
Service Menu
4.7.4
NIBP Pulse Valve
Start test is for starting and Stop test is for stopping
the test.
Set Valve lets you adjust the opening of the pulse
valve.
Pulse Valve Data
For information on general items Pressure, Zero,
Protect handle, Calibr. prot., +15 V power, AD0 to
AD7 as well as Timeouts etc., see section “4.7 NIBP
Module”.
How to check Pulse Valve
Wrap an adult cuff around a pipe and connect the cuff to the module. Select Start test and push the
ComWheel. The pressure rises beyond 240 mmHg and stops. The pulse valve opens. The module
counts the time it takes for the pressure to go down from 240 mmHg to 50 mmHg and displays it on
the screen. The test can be manually stopped by selecting Stop test.
The valve can be adjusted between 0 and 255 (0 for fully closed and 255 for fully open). First select
Set Valve and push the ComWheel. See the pulse valve value and adjust it by turning the ComWheel.
Then push the ComWheel to confirm the value.
The Interval 240 mmHg -> 50 mmHg time should be less than 60 seconds when the valve is 150
and less than 10 when fully opened (255). When fully closed (0), the system should be airtight and
the pressure does not drop. Depending on an individual, the pulse valve may remain closed up to
approx. value 100.
If the measured time deviates much from those above, then the pulse valve or its tubes are faulty.
37
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.7.5
NIBP Buttons/Leds
The selections Auto ON/OFF, Manual ON/OFF, STAT ON/OFF, and Measur. ON/OFF have effect only
on the NIBP module, M-NIBP.
Buttons/Leds Data
For information on general items Pressure, Zero,
Protect handle, Calibr. prot., +15 V power, AD0 to
AD7 as well as Timeouts etc., see section “4.7 NIBP
Module”.
Buttons Checking
The front panel keys function is confirmed by pressing
and releasing the key and observing that OFF turns to
ON at Auto On/Off, and Start Cancel. Set Cycle Time
and STAT On/Off are not in use with E-PSM(P).
38
Document no. M1031519-01
Service Menu
4.7.6
NIBP Pneumatics
Start Pump/Stop Pump: A manual control for the pump.
The selection changes to Stop Pump when the pump
turns on.
Open Exh1/Close Exh1: A manual control for the
exhaust valve 1. The selection changes to Close Exh1
when the valve is opened. This function is not in use with
E-/ M-PRESTN and E-PSM(P) modules.
Open Exh2/Close Exh2: A manual control for the
exhaust valve 2. The selection changes to Close Exh2
when the valve is opened.
Open Zero valve: A manual control for the zero valve. This
function is not in use with E-/ M-PRESTN and E-PSM(P)
modules.
Set Valve: The opening of the pulse valve is adjusted
between 0 and 255 (0 for fully closed and 255 for fully
open). First push the ComWheel, then turn it to adjust the
value on the screen and finally push to set the value.
Reset Clock will zero the time on the display. This function is not in use with E-/ M-PRESTN and E-PSM(P) modules.
Pneumatics Data field
For information on general items Pressure, Zero, Protect handle, Calibr. prot., +15 V power, AD0 to AD7 as well as
Timeouts etc., see section “4.7 NIBP Module”.
Pump, Exh1 Valve, and Exh2 Valve show their states. NOTE: Exh1 Valve has no effect on the module.
Pulse Valve shows how much the valve is opened (0 to 255) during Valve Setting.
How to check Interval 20 mmHg -> 185 mmHg
Select Start pump at different combinations of the valves open/closed and push the ComWheel. The
module counts the time it takes for the pressure to go up from 20 mmHg to 185 mmHg and displays
it. When all the valves are closed, the pump should be able to pump the pressure in about 1 to 4
seconds into an adult cuff wrapped around a pipe. The pump does not stop without selecting Stop
Pump by pushing the ComWheel.
39
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.7.7
NIBP Watchdog
These menu items have only effect on the M-NIBP
modules. They do not effect other NIBP modules.
Test ADULT: is to test watchdog timer in adult mode
(120 to 140 seconds).
Test INFANT: is to test watchdog timer in infant mode
(about 60 to 70 seconds).
Stop Test: is for stopping the test.
Watchdog Data field
For information on general items Pressure, Zero,
Protect handle, Calibr. prot., +15 V power, AD0 to
AD7 as well as Timeouts etc., see section “4.7 NIBP
Module”.
Watchdog Interval: shows the time the +15 Vdirty
stays on during the test.
How to test Adult watchdog time
Select Test ADULT and press the ComWheel. Watchdog interval starts counting up seconds and keeps
on counting as long as the +15 Vdirty is on. The time should be 120 to 140 seconds.
How to test Infant watchdog time
Select Test INFANT and press the ComWheel. Watchdog interval starts counting up seconds and
keeps on counting as long as the +15 Vdirty is on. The time should be 60 to 70 seconds.
40
Document no. M1031519-01
Service Menu
4.8
NMT
Service menu for Neuromuscular Transmission Module,
E-NMT or M-NMT.
Start Curr. test is a test where the module itself checks
the difference between a given current and the measured
current. A 3 kΩ resistance should be connected between
the stimulus electrodes before starting the test. All the
currents checked will be displayed on the service data
screen. After the current value, the status of the test is
shown. If the test is not passed, send the module back to
the factory for calibration.
T1%/ref T1% / ref gives a selection for changing settings
related to the NMT MechanoSensor. A setting of 3 should
always be used for normal monitoring. The settings 1 and
2 are for research purposes only.
Record Data prints out the displayed service data and
circuit board information (id., serial number, and
software id.) on the recorder.
Service Data
Cable shows the type of cable being used.
Cable check value shows the bit amount. To check the value for each cable, see the following chart:
- EMG
-100...+100
- Cable OFF
>1950
- Piezo
900...1100
- Regional block 600....800
Module keys checks the function of the module keys. A blue background appears at the back of the text when a key
is pressed for more than one second.
Stimulus mode shows the selected stimulus. Stimulus mode can be changed using the NMT Setup menu.
Measurement indicates ON/OFF.
T1%, T2% shows the measured response. A value of 1000 corresponds to 100%.
Absolute T1, T2 shows the voltage measured from the A/D converter.
Noise indicates the interference just before the measurement. A typical value is <100.
Offset is an average of the noise measurement. A typical value is 510.
Curr set is the selected current, a value of 700 corresponds to 70 mA.
Curr meas is the measured current, a value of 700 corresponds to 70 mA.
Pulses indicates pulses the module has produced.
Piezo probe T1% and Ref. search shows information related to the MechanoSensor settings.
41
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor's
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the
monitor has failed.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The non-zero values do not
indicate a failure, but the continuous counting (more than 5 per second) indicates either a serial communication
failure, or a module not in place. Also failures in other modules may cause these numbers to rise or be set to 32769.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum in the EPROM is in accordance with the software calculated value.
EEPROM indicates if the values stored in the permanent memory are valid.
The state is either OK, Fail or ? (module not in place or a communication error).
42
Document no. M1031519-01
Service Menu
4.8.1
NMT Setup
Start-up is for starting the neuromuscular transmission
measurement.
Stop/Continue is for stopping/continuing the
measurement.
Stimulus Mode is for changing the stimulus mode. The
choices are: TOF - Train of Four, DBS -Double Burst
Stimulation or ST - Single Twitch mode.
Cycle Time is for changing the time interval for NMT
measurement. The choices are:
for TOF and DBS: Manual and from 10 sec to 15 min.
for ST: 1, 10 and 20 sec.
Current is for changing the stimulus current strength. The
current is either supramaximal (automatic start-up
search) or manually selected.
Pulse Width is for selecting the desired pulse width. The
choices are: 100, 200 or 300 µs.
43
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.9
Oxygen Saturation Modules, E-NSAT, M-NSAT, M-OSAT
N/OSAT Data
NOTE: Preamp Error is indicated on the service menu,
even though module contains MP-204 board.
NOTE: The status and error indicators are not valid for the
M-OSAT, E-NSAT and the M-NSAT..04 revision.
PR shows the pulse rate value [bpm] calculated from the
pleth.
SpO2% shows the oxygen saturation value multiplied by
100.
Next are listed the messages that are sent from the
module to the monitor. Digit ‘0’ means that the message
is not active, ‘1’ is for the active one.
Preamp Error indicates ‘Yes’ if the Preamp (MP-203(4))
board detects an error.
QUART Error indicates ‘Yes’ if an error is detected in the
operation of QUART that is located in the Interface board.
I/O Error indicates ‘Yes’ if an error occurs in the communication between Preamp (MP-203(4)) and Interface board.
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor’s
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the
monitor has broken down.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The nonzero values do not
indicate a failure, but the continuous counting (more than 5 per second) indicates either a serial communication
failure, or a module not in place. Also failures in other modules may cause these numbers to rise or be set to 32769.
ROM indicates whether the checksum in the EPROM is in accordance with the one the software has calculated.
The state is either OK, Fail or ? (module not in place or a communication error).
44
Document no. M1031519-01
Service Menu
4.10 More
45
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.11 Interface module, E-INT, M-INT
Gases, SpO2, NIBP, Spirometry, SvO2/C.O. indicate the
parameters for which service data is available. The data
which can be seen on those pages is raw data from the
interfaced monitors, which will be processed for the
normal screen.
Service Data
I-INT: Indicates the status of the interface via the
UPI section.
B-INT: Indicates the status of the interface via the 4
interface channels of B-INT or two channels of E-INT/
M-INT module.
id: The name of the interfaced monitor, e.g. Ultima.
state: describes the state of the connection, alternatives
are:
'init' - the channel is initialized
'wait' - the monitor is waiting for the external monitor
'online' - the connection is ready
'search' - the external monitor is being searched
rt: real time values that are available via the interface.
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor's
inquiry.
Bad checksums is a cumulative number that indicates how many times communication from the module to the
monitor has failed.
Bad c-s by mod is a cumulative number that indicates how many communication errors the module has detected.
The monitor starts counting these items at power up and resets to zero at power off. The nonzero values do not
indicate a failure, but the continuous counting (more than 5 per second) indicates either a serial communication
failure, or a module not in place. Also failures in other modules may cause these numbers to rise or be set to 32769.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum in the ROM is in accordance with the software calculated value.
The state is either OK, Fail or ? (module not in place or a communication error).
46
Document no. M1031519-01
Service Menu
4.11.1 Gases
The data on this page is the raw data received from
the interfaced monitor. This data will be processed
further for the normal screen.
4.11.2 Sp02
The data on this page is the raw data received
from the interfaced monitor. This data will be
processed further for the normal screen.
47
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.11.3 NIBP
The data on this page is the raw data received from
the interfaced monitor. This data will be processed
further for the normal screen.
4.11.4 Spirometry
The data on this page is the raw data received from
the interfaced monitor. This data will be processed
further for the normal screen.
48
Document no. M1031519-01
Service Menu
4.11.5 Sv02/C.O.
The data on this page is the raw data received from
the interfaced monitor. This data will be processed
further for the normal screen.
49
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.12 Tonometry
Service menu for Gastric Tonometry Module.
Service Data
Tonometry: Another route to reach Tonometry setup
menu.
PressSensCal: A selection to enter the module pressure
sensor calibration menu.
System Test: A selection to enter the module system
test.
CO2 Sensor: A selection to enter the module CO2 sensor
menu.
Pneumatics: A selection to enter the module
pneumatics menu.
AD: A selection to enter the module AD value display.
Record Data: A selection to print out the shown service
data to the device defined in the ...Service - Record
Data menu.
TONO
Statuses (HEX): See APPENDIX A How to read HEX numbers.
General: Module general status. See Table 2 Module general status for a detailed description of the message.
Table 2
HW
Module general status
bit 0-5
Not used
bit 6
State error
bit 7
Communication failure
bit 8
Power failure
bit 9
Clock failure
bit 10
EEPROM checksum failure
bit 11
EEPROM writing failure
bit 12
ROM failure
bit 13
RAM failure
bit 14
Test mode
bit 15
Init mode
Module hardware status. See Table 3 Module hardware status for a detailed description of the
message.
50
Document no. M1031519-01
Service Menu
Table 3
Module key
Module hardware status
bit 0
Lamp ON
bit 1
Stepper motor ON
bit 2
Zeroing valve ON
bit 3
Pump valve ON
bit 4-15
Not used
Module keyboard status. See Table 4 Module keyboard status for a detailed description of the
message.
Table 4
Module keyboard status
bit 0
Button 1 (start/stop) pressed
bit 1
Button 2 (Lab.Data) pressed
bit 2-15
Not used
Error Statuses (HEX):
General error
Pneuma error
Module general error status. See Table 5 Module general error status for a detailed description of the
message.
Table 5
Module general error status
Bit
Description
What to do
bit 0-1
Not used.
-
bit 2
Zeroing error. Zero gas signal out of limits or pressure CO2 sensor faulty. Send the
or temperature signal varying during measurement. module to the factory for
repair.
bit 3
CO2 measurement error. CO2 signal out of limits or
pressure or temperature signal varying during
measurement.
bit 4
Measurement error. Sensor temperature,
CO2 sensor faulty. Send the
measurement pressure or absorbance is out of limits. module to the factory for
repair.
bit 5
Calibration error. Failure in calibration.
Recalibrate.
bit 6
Pneumatic error.
See pneumatic error status
bits for details.
bit 7
Lamp pulsing error.
CO2 sensor faulty. Send the
module to the factory for
repair.
bit 8-15
Not used.
-
CO2 sensor faulty. Send the
module to the factory for
repair.
Module pneumatics error status. See Table 6 Module pneumatics error status for a detailed
description of the message.
51
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Table 6
Module pneumatics error status
Bit
Error label
Description
What to do
0
pumping error
Stepper motor is not able to generate
negative pressure at the pump
pressure sensor during zeroing.
Check the function of the stepper
motor.
1
eq. to amb. press failed Before filling the catheter, the pressure Calibrate the pressure sensors. Check
in the module tubing is equilibrated to the pump valve function.
the ambient pressure by switching the
pump valve on and off. If ambient
pressure is not reached, this error is
shown.
2
tubing/zero block occl
Pressure at the pump pressure sensor Check tubing/valves for occlusion.
gets too low, when air is aspirated
though the zeroing valve.
8
press sens values differ
Pump pressure and catheter pressure Calibrate the pressure sensors.
readings differ more than 50 mbars.
9
pneuma fatal error
This error is shown, if the pneumatic
error occurred is considered fatal.
Check for other pneumatics errors.
10
cath press too low
Catheter pressure reading is below
reasonable pressure values.
Make sure that you are not applying too
low pressure to the catheter connector.
Calibrate the pressure sensors.
11
cath press too high
Catheter pressure reading is above
reasonable pressure values.
Make sure that you are not applying too
high pressure to the catheter connector.
Calibrate the pressure sensors.
12
pump press too low
Pump pressure reading is below
reasonable pressure values.
Make sure that you are not applying too
low pressure to the catheter connector.
Calibrate the pressure sensors.
13
pump press too high
Pump pressure reading is above
reasonable values.
Make sure that you are not applying too
high pressure to the catheter connector.
Calibrate the pressure sensors.
HW error
Module hardware error status. See Table 7 Module hardware error status for a detailed description of
the message.
52
Document no. M1031519-01
Service Menu
Table 7
Testbit
Voltages
Module hardware error status
bit 0
Lamp error
bit 1, 2, 3
not used
bit 4
CPU EEPROM error
bit 5
Sensor EEPROM error
bit 6
Internal AD converter error
bit 7
External AD converter error
bit 8
CO2 termopile error
bit 9
Reserved
bit 10
Temperature detector error
bit 11
Pump pressure sensor error
bit 12
Catheter pressure sensor error
bit 13
Pneumatic power failure
bit 14-15
Not used
Testbit is a module production phase test status and is always 0000 (HEX). If the testbit status is ≠
0000, then the module should be returned to the factory.
Vdd; 5 V digital units driving voltage received from the module frame.
5vdc; 5 Volts of the module derived internally from 15vdc.
15vdc; 15 Volts of the module received from the module frame.
Pneuma voltage; 15 V voltage driving pneumatic elements of the module, derived from 15V dirty.
15V dirty; 15 V voltage received from the module frame.
53
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.12.1 Tonometry
This is another route to reach Tonometry setup menu, Others - Tonometry. For a detailed description
on how to use this menu see “User’s Reference Manual”.
Start / Stop Cycling is for starting or stopping the
measurement.
Display with PgCO2 is for defining the calculated value
displayed with PgCO2. The choices are Pg-Pa, Pg-ET or
pHI.
Lab Data is for entering the blood gas values nad
calculations.
PgCO2 Calibration is for calibrating the tonometry.
PgCO2/Pg-ET Alarms is for disabling/enabling alarms
and adjusting the alarm limits.
How to calibrate PgCO2
1.
2.
3.
4.
5.
Connect the calibration gas sampling line to the regulator and to the module’s catheter
connector.
Select PgCO2 Calibration.
Wait until the text ‘Start feeding gas and press ComWheel. Feed gas until Adjust message is
displayed’ appears. Open the regulator and start feeding gas. Press the ComWheel and
continue feeding gas until the text ‘Adjust’ appears on the display.
Check that the displayed values match the values on the calibration gas container. Adjust with
the ComWheel, if necessary.
If airway gases are monitored, it is recommended to calibrate the airway gases at the same
time.
54
Document no. M1031519-01
Service Menu
4.12.2 Press Sensor
Start Calib.: A selection to start a module pressure
sensor calibration sequence. The procedure is guided
online.
Record Data: A selection to print out the shown service
data to the device defined in the ...Service - Record
Data menu.
TONO service data
Amb Press; ambient pressure measured by the pressure
sensor. All the pressure values are given in both mmHg
and mbar on this page.
Pump Press; pressure measured from the pumping unit.
Cath Press; pressure measured from the catheter line.
User Cal Press; pressure that the user sets during the
calibration sequence according to the pressure that is
applied to the catheter port. The set value should be
close to 100 mmHg.
User Amb Press; pressure that the user sets during the calibration sequence according to the current ambient
pressure in the room.
Store; a selection for storing/discarding the newly gained calibration values.
Last Press calibration date; data read from the module that tells when the module has last been calibrated.
55
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.12.3 System Test
Start Test: A selection to start the automatic system test
sequence. The procedure is guided online.
Stop Test: A selection to stop the automatic system test
sequence.
Record Data: A selection to print out the shown service
data to the device defined in the ...Service - Record
Data menu.
TONO
Cathpres; pressure measured from the catheter line
[mbar].
Ambpres; ambient pressure in the room [mbar].
Pumppres; pressure measured from the pumping unit
[mbar].
System test results; detailed information of the test
results of different system parts. The meaning of the
messages:
- “OK”, the part successfully passed the test
- “FAIL”, the part failed in the test
- “N/A”, the test could not be carried out properly.
See Table 8 Description of system test for a detailed description of the tested parts.
Table 8
Description of system test
Test label
Description
If test fails
Pump unit function
Stepper motor aspirates/pushes room air
through the zeroing valve. If the stepper is
working properly, it is able to generate small
negative/positive pressure at the pump unit
pressure sensor.
Check the function of stepper
motor.
Cath press = pump press
Pump pressure sensor and catheter pressure
Calibrate the pressure sensors.
sensor readings are compared at three
pressures: at ambient pressure, at approx. +100
mbar and –100 mbar.
Tubing leak test
The air tightness of the module inner tubing from Check tubing and connections
the zeroing valve to the pump valve is tested.
for leaks.
Pump unit leak test
The air tightness of the pump unit is tested.
56
Document no. M1031519-01
Check pump unit for leaks.
Service Menu
Test label
Description
If test fails
Cath conn. leak test
The air tightness of the zeroing unit and catheter Make sure that the catheter
connector is tested.
connector is properly closed
during the test. Check the zeroing
unit and the catheter connector
for leaks.
Block test
Air is aspirated through the zeroing valve. If
Check the tubing/valves for
pressure at the pump pressure sensor drops too blocks.
much, the tubing/valves from the zeroing valve
to the pump pressure sensor is blocked.
Zero valve function
Module pneumatic system pressurized and then Check the function of the zeroing
the zeroing valve is opened to room air. If the
valve.
pressure does not drop, the zeroing valve may
not be functioning.
Pump valve function
Module pneumatic system pressurized and then Check the function of the pump
the pump valve is opened to room air. If the
valve.
pressure does not drop, the pump valve may not
be functioning.
57
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.12.4 CO2 Sensor
Lamp ON/OFF: A selection to toggle the sensor lamp on
and off.
Meas Signal: A selection to start an automatic signal
measurement sequence. This sequence measures
sensor lamp signal levels.
Meas Zero: A selection to start an automatic zeroing
measurement sequence.
Meas Gas: A selection to start an automatic gas
measurement sequence. This sequence first performs
the zeroing measurement. Then it measures the CO2
concentration of the sample of arbitrary gas aspirated
from the catheter port.
Record Data: A selection to print out the shown service
data to the device defined in the ...Service - Record
Data menu.
TONO
Calib gain; CO2 measurement gain factor that is set in
calibration.
Lamp on current; sensor lamp current when lit.
Lamp off current; sensor lamp current when off.
Block temp; sensor temperature [°C] (in degrees centigrade).
Detector offset; CO2 detector offset voltage.
Lamp status; displays whether the sensor lamp is on or off.
CO2 AD; signal from CO2 sensor thermopile (AD counts).
CO2 signal; thermopile signal maximum – minimum when the lamp is blinking (AD counts).
CO2 zero; thermopile signal maximum - minimum during sensor zeroing when the lamp is blinking (AD counts).
CO2 absorbance; calculated light absorbance during CO2 measurement.
CO2 concentration; CO2 concentration (%) in sensor (does not include compensations related to catheter
measurement).
MEAS TEMP; CO2 sensor temperature during signal measurement [°C].
MEAS PRESS; CO2 sensor pressure during signal measurement [mbar].
ZERO TEMP; CO2 sensor temperature during zeroing measurement [°C].
ZERO PRESS; CO2 sensor pressure during zeroing measurement [mbar].
58
Document no. M1031519-01
Service Menu
4.12.5 Pneumatics
Zero valve: A selection to toggle the zero valve on/off.
Press valve: A selection to toggle the pump valve on/off.
Record Data: A selection to print out the shown service
data to the device defined in the ...Service - Record Data
menu.
TONO
Cathpres; pressure measured from the catheter line
[mbar].
Ambpres; ambient pressure in the room [mbar].
Pumppres; pressure measured from the pumping unit
[mbar].
Pneuma Power; displays whether electricity has been
connected to the pneumatics system or not.
Zero valve; displays whether the zero valve is on or off.
Pump valve; displays whether the pump valve is on or off.
Gas removed count; displays how many times gas is
removed from the catheter during a measurement cycle.
Pneumatic errors; detailed information of the performance of different pneumatics system parts.
The meaning of the messages:
‘NO’, the part performed OK during the measurement = ‘this error did not occur’
‘YES’, the part failed during the measurement = ‘this error did occur’
See Table 6 Module pneumatics error status for a detailed description of the messages.
59
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.12.6 AD
Record Data: A selection to print out the shown service
data to the device defined in the ...Service - Record
Data menu.
TONO
All the numbers in this section are AD counts, i.e.
computer internal data.
EXTERNAL ADC
CO2; CO2 sensor CO2 signal.
temp; CO2 sensor temperature signal.
cath press; pressure measured from the catheter line.
pump press; pressure measured from the pumping unit.
INTERNAL ADC
VDD; 5 V digital units driving voltage received from the
module frame.
5V; 5 Volts of the module derived internally from 15vdc.
15V; 15 Volts of the module received from the module frame.
pneuma voltage; 15 V voltage driving pneumatic elements of the module, derived from 15 V dirty.
CO2 det offset; CO2 detector offset voltage.
lamp current; CO2 sensor lamp current.
15V dirty; 15 V voltage received from the module frame.
60
Document no. M1031519-01
Service Menu
4.13 EEG & EP
Service menu for EEG Module for
electroencephalography and evoked potentials (EP)
measurements.
Check Electr.: Headbox measures impedance of
electrodes. Works the same way as from EEG menu or the
headbox/module button.
Start AEP: AEP measurement is started with current AEP
settings.
Module: Service data is changed to the module view
(some of the data in this view is though from headbox).
Headbox: Service data is changed to headbox view.
Service data in module view
Measurement shows whether the EEG measurement is
ON or OFF. Measurement should start by itself when the
leads have been on for about 15 seconds.
Montage shows the active montage in monitor.
HB Montage shows the montage attached to headbox. 0
means no montage, 1 basic, 2 general,
3 AEP, 4 Mont4, etc. up to 8, which means Mont8.
Montage Type shows whether the montage is bipolar or referenced.
EP Start/Stop is highlighted when the EP Start/Stop button is pressed in headbox or module.
Imp. Check is highlighted when the Imp. Check button is pressed in headbox or module.
Imp. Meas. shows 1 if the impedance measurement is on in the module.
Headbox Off shows 1 if the headbox cable is not connected to the module.
EP Meas. shows 1 if the evoked potential measurement is active in the module.
Sending EP shows 1 if the module has acquired 100/200 new epochs and is sending them to the monitor.
Par. Error shows 1 if the evoked potential parameters active in the module are conflicting with each other.
Reserved 1 is reserved for future use.
Reserved 2 is reserved for future use.
HB Mod Timeouts is a cumulative number that indicates how many times the headbox has not responded to the
module’s inquiry.
HB Mod Bad Checksum is a cumulative number that indicates how many times there has been an error in the message
from the headbox to the module.
Mod HB Bad Checksum is 1 if there has been errors in the messages from the module to the headbox.
Mod Mon Timeouts is a cumulative number that indicates how many times the module has not responded to the
monitor’s inquiry.
Mod Mon Bad Checksum is a cumulative number that indicates how many times there has been an error in the
message from the module to the monitor.
Mon Mod Bad Checksum is a cumulative number that indicates how many times there has been an error in the
message from the monitor to the module.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum at the EPROM is in accordance with the one the software has calculated.
EEPROM indicates if the values stored in the permanent memory are valid.
The states in memory checks are OK, Fail or ? (module not in place or a communication error).
61
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Service data in Headbox view
EP Start/Stop is highlighted when the EP Start/Stop
button is pressed in the headbox or module.
Imp. Check is highlighted when the Imp. Check button
is pressed in the headbox or module.
Active shows 1 if the channel is active.
Lead off+ shows the lead off status of all plus
electrodes. 0 means that the lead is on and 1 that the
lead is off.
Lead off- shows the lead off status of all minus
electrodes. 0 means that the lead is on and 1 that the
lead is off.
Imped+ shows the impedance of plus electrodes of the
last impedance check in all channels.
Imped- shows the impedance of minus electrodes of the
last impedance check in all channels.
BSR shows the burst-suppression classification of EEG waveforms. 0 means artifact, 1 suppression, 2 burst and 3
invalid (the EEG is not classified).
Artefact shows the artefact status of all channels. 0 means that there are no artefacts on the signal and 1 means
that there are artefacts.
Noise shows 1 if the activity of FEMG is too high for clean EEG signal and that EEG is not probably reliable.
EMG AD shows the latest AD conversion result of FEMG signal without any filtering or scaling.
Leadset AD shows the latest AD conversion result of lead set signal without any scaling.
Bipolar shows the montage type that is active in the module and headbox. 1 means bipolar and 0 referenced.
60 Hz is 1 if the power frequency filter is set for 60 Hz power frequency.
Imp. Meas. shows 1 if the impedance measurement is on in the headbox.
Imp. Check Failed shows 1 if the impedance check has failed.
Mu
EP Meas. shows 1 if the evoked potential measurement is active in the headbox.
High EP Sampl. Rate shows 1 if the headbox uses higher sampling rate for 10 ms EP measurement.
EP Epoch Points shows the number of samples collected for each epoch.
EP Channels shows the number of channels used in EP measurement.
Hb ROM Error is 1 if the checksum at the EPROM is not in accordance with the one the software has calculated.
62
Document no. M1031519-01
Service Menu
4.13.1 EEG & EP Setup
The items in the setup menu are a collection of items in
normal EEG and EP menus. There are no special service
settings in this menu.
Imp. Cycle: Impedance measurement repetition time.
Select Montage: Selection of headbox’s electrode
configuration.
EEG Channels: Number of active channels in EEG
measurement.
Montage Type: Selection of bipolar (Bip)/referenced
(Ref) montage.
Cycle: EP measurement repetition time.
Stim. Frequency: EP measurement’s stimulation
frequency.
Stim. Intensity: Intensity of EP stimulus.
63
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.14 BIS
Service menu for BIS Module, E-BIS or M-BIS, for Bispectral index measurements.
Module service page
Check Sensor activates the sensor impedance check.
Module
Measurement indicates if BIS Engine is on: ON/OFF.
Imp. Check Key indicates that the key in the module
front panel works properly.
Bis Menu Key indicates that the key in the module front
panel works properly.
Impedance Meas indicates the impedance
measurement mode. The modes are
CYCLIC/COMBINED/GROUND/OFF.
BIS Engine errors: error messages created by DSC or
BIS Engine. For a detailed description of the error
message see Table 11 BIS Engine and DSC error
messages.
Statuses (HEX): See APPENDIX A How to read HEX
numbers.
General Status1 indicates the general status of the
module. For a detailed description of the message see Table 9 Module general status.
Bis_status1 indicates the BIS Engine status. See Table 10 BIS Engine status for a detailed description of the
message.
Msgs to BE number of data packages sent from the interface board to BIS Engine.
Msgs from BE number of data packages sent from BIS Engine to the interface board.
Mod Mon Timeouts is a cumulative number that indicates how many times the module (interface board) has not
responded to the monitor’s inquiry.
Mod Mon Bad Checksum is a cumulative number that indicates how many times there has been an error in the
message from the module (interface board) to the monitor.
Mon Mod Bad Checksum is a cumulative number that indicates how many times there has been an error in the
message from the monitor to the module (interface board).
Bad Checksums from BIS is a cumulative number that indicates how many times there has been an error in the
message from the BIS Engine to the module interface board.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum at the EPROM is in accordance with the one the software has calculated.
EEPROM indicates if the values stored in the permanent memory are valid.
The states in memory checks are OK, Fail or ? (module not in place or a communication error).
Measured parameters indicated:
BIS indicates BIS index; range 0...1000 (corresponds to 0...100)
SQI indicates signal quality index; range 0...1000 (corresponds to 0..100)
EMG indicates EMG activity level; range 0...10000 (corresponds to 0...100dB NOTE! On the display, EMG will be
shown between 30...55dB on the bar graph or 30...80dB on the trend)
SR indicates supression ratio; range 0...100 (corresponds to 0...100%)
64
Document no. M1031519-01
Service Menu
General_Status1 Module general status
Table 9
Module general status
bit 0-5
Not used
bit 6
State error
bit 7
Communication failure
bit 8
Power failure
bit 9
Clock failure
bit 10
EEPROM checksum failure
bit 11
EEPROM writing failure
bit 12
ROM failure
bit 13
RAM failure
bit 14
Test mode
bit 15
Init mode
BIS_Status1 BIS Engine status
Table 10
BIS Engine status
bit 0
Check Sensor key pressed
bit 1
BIS key pressed
bit 2
Inpedance check mode cyclic
bit 3
Impedance check mode combined
bit 4
Impedance check mode ground
bit 5
Impedance check off
bit 6
Measurement on
bit 7
EEG measurement on
bit 8
Impedance check on DSC channel 1 passed
bit 9
Impedance check on DSC channel 2 passed
bit 10
BIS Engine powerup failure
bit 11
DSC selftest failure
bit 12
DSC quick test failure
bit 13
DSC selftest on
bit 14
No data from BIS Engine
bit 15
Not used
Table 11
BIS Engine and DSC error messages
65
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Message
Errors of type 2
Illegal message ID
Errors for layer 3 packets
Illegal command parameter
Illegal length for layer 2 data
Disabled interrupt received UART transmitter empty interrupt
UART related errors
Disabled interrupt received UART modem interrupt
No status nibble received
DSC related errors
DSC not connected
DSC disconnected after test failure
Illegal DSC ID
DSC power regulation fault
DSC interface fault
DSC did not respond to command
Illegal PIC ID
DSC overcurrent
DSC overrun
EEPROM Bad packet length
EEPROM Bad checksum
EEPROM Bad code length
EEPROM Illegal packet subtype
EEPROM physical write error
EEPROM NOT_DATA_TIMEOUT
66
Document no. M1031519-01
Software update related errors
Service Menu
4.14.1 Sensor
Sensor type: indicates the type of the sensor connected.
Lot code: indicates the manufacturing lot code of the
sensor. The lot code contains the manufacturing date
and shift.
Serial no: indicates the serial number of the sensor.
Shelf life: indicates max storage duration.
Usage count: indicates how many times the sensor has
been attached/detached. Not in use.
Mains Freq.: indicates the set mains frequency;
50Hz/60 Hz.
Sensor Impedances: indicates the last measured
impedances.
Imped. indicates the measured impedance value in
Kohms.
Qualif. indicates the quality of the measured
impedance; PASS/FAIL.
BE powerup test: indicates the status of BIS Engine power up test: PASS/FAIL.
DSC selftest ch1: indicates the DSC selftest status for channel 1: PASS/FAIL.
DSC selftest ch2: indicates the DSC selftest status for channel 2: PASS/FAIL.
Measured parameters indicated:
BIS indicates BIS index; range 0..1000 (corresponds to 0..100)
SQI indicates signal quality index; range 0..1000 (corresponds to 0..100)
EMG indicates EMG activity level; range 0..10000 (corresponds to 0..100dB)
(NOTE! On the trend display, EMG will be shown between 30..80dB)
SR indicates supression ratio; range 0...100 (corresponds to 0..100%)
Statuses (HEX): See APPENDIX A How to read HEX numbers.
DSC status: indicates the DSC status for the four channels. See Table 12 DSC status for a detailed description of
the message.
Sensor status: indicates the Sensor status. See Table 13 Sensor status for a detailed description of the message.
BE powup stat: indicates the BE power up status. See Table 14 BE power up status for a detailed description of the
message.
67
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Table 12
DSC status
bit 0
Noise test
bit 1
BIS key pressed
bit 2
Blocked droop test
bit 3
Unblocked gain test
bit 4
Impedance wait time out test
bit 5
Noise timeout test
bit 6
Blocked timeout test
bit 7
Unblocked timeout test
bit 8
DSC not connected test
bit 9
Not used test
bit 10
Not used test
bits 11 15
Not used
Table 13
Sensor status
bit 0
Quick selftest pass
bit 1
Quick selftest gain
bit 2
Quick selftest noise
bit 3
Quick selftest fail
bit 4
Quick selftest valid
bit 5
Sensor valid
bit 6
Sensor invalid
bit 7
Sensor too many uses
bit 8
Sensor expired
bit 9
Sensor validity unknown
bits 10
-15
Not used
Table 14
BE power up status
bit 0
XRAM test
bit 1
Dma test
bit 2
Timer test
bit 3
Fpga test
bits 4 -15 Not used
68
Document no. M1031519-01
Service Menu
4.14.2 BIS Setup
Automatic Check: A selection to define whether the
automatic sensor check is used ON/OFF.
Test DSC indicates the status of the DSC self test;
PASS/FAIL.
Filters: A selection to define if filters are used
ON; disturbances are filtered from the raw EEG signal
OFF; raw EEG signal is shown.
69
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.15 Entropy
Check Sensor Module measures the impedance of
sensor electrodes. Works the same way as from Entropy
menu or module key.
Module Service data is changed to the module view.
Measurement shows whether the Entropy measurement
is ON or OFF. Measurement should start by itself when the
sensor is attached to the patient.
Last service shows the date of last maintenance.
Entropy refers to the respective module key. Is
highlighted when the Entropy key is pressed on the
module. (Opens the Entropy menu.)
Check Sensor is highlighted when the Check Sensor key
is pressed on the module. Activates the sensor check.
Mains shows the currently used mains frequency, 50 or
60 Hz:
BSR Status shows Burst if the module is not currently detecting suppressed EEG. Shows Suppression if the module is
detecting suppressed EEG periods.
Artefact shows Off, if there is no high-frequency noise present, On if the module detects noise.
Diathermy shows On, if the module is detecting diathermy (i.e., electrocautery).
AD clipped shows On, if the signal is getting clipped at the A/D converter.
Alg. ver. (Mon) shows the monitor algorithm version number.
Alg. ver. (Mod) shows the module algorithm version number.
Alg. ver. used shows the currently used algorithm version.
Timeouts is a cumulative number that indicates how many times the module has not responded to the monitor’s
inquiry.
Mod Mon Bad Checksum is a cumulative number that indicates how many times there has been an error in the
message from the module to the monitor.
Mon Mod Bad Checksum is a cumulative number that indicates how many times there has been an error in the
message from the monitor to the module.
RAM indicates the state of the RAM memory.
ROM indicates whether the checksum at the EPROM is in accordance with the one the software has calculated.
EEPROM indicates if the values stored in the permanent memory are valid. The states in memory checks are OK, Fail
or ? (module not in place or a communication error).
70
Document no. M1031519-01
Service Menu
4.15.1 Sensor
Sensor Service data is changed to the sensor view.
Entropy refers to the respective module key. Is
highlighted when the Entropy key is pressed on the
module. (Opens the Entropy menu.)
Check Sensor is highlighted when the Check Sensor key
is pressed on the module. Activates the sensor check.
Cable indicates whether the Entropy sensor cable is
connected to the module or not.
Sensor indicates whether the Entropy sensor is
connected to the cable or not.
Sensor S/N module reads the manufacturing serial
number from the sensor chip.
Sensor Lot module reads the manufacturing lot number
from the sensor chip.
Lead 1/2/3 shows the lead on/off status of all sensor electrodes.
Imped. 1/2/3 shows the respective impedance value of each sensor
electrode of the last impedance check.
Imp. Meas. shows On if the Automatic check (sensor impedance
measurement) is on in the module.
Imp. Check shows OK if the last impedance check has been
successful.
71
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.16 DIS Interfacing
4.16.1 Interfacing
How to interface
To select the parameter data source:
•
•
•
Press the Monitor Setup and select Interfacing.
Select the desired measurement parameter, for example Gases.
Select the desired source by name, for example Aest.
NOTE: The name of the device is visible on the list only if the device is correctly connected to the
module.
72
Document no. M1031519-01
Service Menu
4.16.2 Status Page
Access via Monitor setup - Interfacing.
The selection Next page is available, if more than 8 DIS
modules are connected to the DIS bus simultaneously.
Interfaces
The menu displays a list of all connected DIS modules
and the statuses of the corresponding external devices.
If the bus voltage is too low, you cannot add more
devices. ‘DIS module bus voltage low. Do not add more
devices or reduce cable length’ message appears.
4.16.3 DIS Interfacing
DIS Interfacing
The menu displays submenus for all connected DIS
modules.
73
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
DIS Module specific page
Service Data
Product name: DIS module name.
Product type: DIS module type.
Driver sw id: DIS module software and its release date.
Short product name: DIS module name.
Module serial number: DIS module serial number.
HW card type: PCB type.
HW id: DIS module PCB identification number.
HW test date: DIS module PCB testing date.
Unit serial number: DIS module PCB serial number.
Comment field: Indicates the status of the external
device.
bus voltage: DIS bus voltage, measured by the
Central Processing Board in S/5 Compact Monitor. The value should normally be within 6…8
V.
tout: DIS module timeouts, seen by the monitor. The value should not increase more than by 5 per second.
cse: DIS module checksum errors, seen by the monitor. The value should not increase more than by 5 per second.
rx: The number of data packets from the external device received by the DIS module.
rx err: The number of data errors from the external device received by the DIS module.
tx: The number of data packets to the external device sent by the DIS module.
Ram: Status of DIS module RAM memory.
Rom: Status of DIS module ROM memory.
EEPROM: Status of DIS module EEPROM memory.
74
Document no. M1031519-01
Service Menu
5
Set/Test
In the power supply unit, there is a safety element, which
needs refreshing at least every 1.5 seconds. If the main
CPU's software will not refresh, safety element gives
reset to main CPU. In normal operation the main CPU's
software refreshes safety element every 0.2 seconds.
The purpose of the safety element is to restart the
monitor if there is a serious malfunction. This feature is
useful in two cases: when the main CPU's software is
not able to control the monitor, and when the software
controls the monitor but detects a serious malfunction.
Watchdog tests ensure the proper functionality of the
safety element's various sections.Watchdog test
ensures directly that the watchdog of the power unit
functions properly. Choosing this test prevents safety
element from refreshing and shows running seconds
with an accuracy of 0.1 seconds.
The test should have the following result when the safety
element is working properly: The monitor will restart after
1.5 seconds from the start of the test. In malfunction: '>20 s' is displayed, and the test will interrupt. In this case, the
fault is in the safety element of the power unit.
WD by Overload test ensures the functionality of a feature, where the software controls the monitor, but detects an
overload situation in the main CPU.
The test should have the following result when the feature is working properly: The monitor will restart after 15 seconds
from the start of the test.
WD by UPI test ensures the functionality of a feature, where the software controls the monitor, but detects
amalfunction at the UPI section. The test will prevent the UPI processor from functioning during the test.
Immediately after the test starts the plotting stops. The test should have the following result when the feature is
working properly: The monitor will restart the UPI section without any visual effects.
WD by GSP ensures the functionality of a feature, where the software controls the monitor, but detects a malfunction
at the GSP section. The test will prevent GSP processor from functioning during the test.
The test should have the following result when the feature is working properly: The monitor will restart the GSP section
without any visual effects.
Factory Reset restore factory default settings and clear data memories. Factory reset should be run if monitor
software is replaced or if the SRAM/Timekeeper IC, or its battery is replaced.
75
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
5.1
Country Settings
Language
Select the software language.
National Reqs
Select the software features, which include national
requirements.
Power Frequency
Set the power frequency (50 Hz/60 Hz). This setting is
used to filter out possible power frequency interference
from the parameter measurements.
Time format
Set the time format of the real time clock (24 h/12 h).
76
Document no. M1031519-01
Service Menu
6
Service Log
Error, event, alarm and maintenance data is stored in Service Log.
The service log contains information about the occurred monitor errors, events and alarms since the last factory reset
or service log reset. The service log is saved in the EEPROM memory of the main CPU board. The user can also store
different maintenance events in the maintenance log.
Maintenance menu is for setting and viewing the
maintenance information of the monitor.
Error History is for selecting the error history view onto
the right side of the menu.
Event History is for selecting the event history view onto
the right side of the menu.
Alarm History is for selecting the alarm history view onto
the right side of the menu.
Scroll Last Er (Ev) is for scrolling the error / event /
alarm information on the right side of the menu.
Scroll Counters is for scrolling the error / event / alarm
counters on the right side of the menu.
Record Data is for recording the service log information
onto the recorder.
Reset Log is for clearing up the content of the service
log. This function should be run after a performed
maintenance. In Error/Event history view, the Reset Log
command clears up both the error and the event log. In the Alarm History view, the Reset Log command resets only
the alarm history log.
77
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
6.1
Maintenance
The Maintenance History Log gives the user a possibility to store the maintenance history of the monitor. The user can
store different planned maintenance (PM) events, repairs and upgrades in the maintenance history log.
Running hours: shows how many hours the monitor has
been on. User cannot reset this value.
since This date and time is set at the factory and it
shows the manufacturing date and time. User cannot
reset this date and time.
since last 1 year PM: shows the running hours since
the last 1 year PM storing.
Last events: The section shows the last maintenance
events and the time of their occurrence.
Event counters: The section contains counters for each
different maintenance events. The time of occurrence of
the last event is shown beside each counter.
6.1.1
Planned Maintenance
1 Year PM gives you the possibility to store a 1 year PM
event in the maintenance history log.
Other PM gives you the possibility to store another PM
event in the maintenance history log.
Notify on PM This feature is for future purposes.
78
Document no. M1031519-01
Service Menu
6.1.2
Repair
The repair menu gives the user a possibility to store repair events in the maintenance history log. The different
repairs that can be saved are: Display, Power Supply,
Recorder, Frame (e.g. board in the frame), Parameters (e.g. a board in the parameter module) or Other (a
miscellaneous repair not specified by previous options).
6.1.3
Upgrade
The upgrade menu gives the user a possibility to store
the upgrades in the maintenance history log.
79
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
6.2
Error History
Last Errors: The section shows the last monitor errors
and the time of their occurence.
Error counters: The section contains counters for each
different (detected) monitor error. The time of
occurrence of the last error is shown beside each
counter.
Last log reset: The date and time of the last Error/Event
log reset.
Possible errors:
Fast cold start indicates the number of erroneous cold
starts with power off time less than 20 seconds. The
reason can be either a failing lead acid battery or a
software problem that was solved by the hardware
watchdog circuitry located in the monitor’s power supply
unit.
GSP watch-dog timeout indicates an erroneous restart
controlled by the main CPU board and caused by the
display controller board. The restart is listed as a fast cold start.
UPI watch-dog timeout indicates an erroneous restart controlled by the main CPU board and caused by the UPI
section. The restart is listed as a fast cold start.
6.3
Event History
Last events: The section shows the last events and the
time of their occurrence.
Event counters: The section contains counters for
each different (detected) event. The time of occurrence
of the last event is shown beside each counter.
Last log reset: The date and time of the last
Error/Event log reset.
Possible events:
Cold start is a start-up with power off time more than
15 minutes. The trend memory is cleared and
monitoring starts with the user default settings.
Warm start is a start-up with power off time less than
15 minutes. The trend information and possible
temporary settings are still available.
80
Document no. M1031519-01
Service Menu
6.4
Alarm History
Last alarms: The section shows the last events and the
time of their occurrence.
Alarm counters: The section contains counters for
each different (detected) event. The time of occurrence
of the last event is shown beside each counter.
Last log reset: The date and time of the last alarm log
reset.
81
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
7
Record Data
In this menu, the user can specify where to print from
any service menu. The setting goes into the permanent
memory of the monitor. Only one option can be chosen
at a time. The options where to print are: To Printer, To
Recorder and To Memory Card. Only the option To Recorder can be selected.
82
Document no. M1031519-01
Service Menu
8
Remote Access
Remote Access menu is for setting the interface with an
external PC that runs the Virtual Support software, which
is a service diagnostic tool for remote diagnostics
purposes.
When the access mode is set to Normal (the default), the
PC can only read service menu data from the monitor.
With the access mode Extended, the PC can also activate
the monitor’s service menu functions.
NOTE: Patient monitoring is not possible, when the access
mode Extended is selected. The access mode turns back
to Normal, if the monitor is restarted or if the service menu
is closed.
83
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
84
Document no. M1031519-01
Appendix A, How to read HEX numbers
APPENDIX A How to read HEX numbers
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Some statuses on BIS and Tonometry Module service pages are given as HEX (hexadecimal)
numbers. To understand them, please read the following:
A HEX number has a base of 16 instead of 10. This means that every character in a number can have
a value between 0 and 15. Numbers from 0 to 9 are displayed as if they were normal 10-based
numbers. Numbers from 10 to 15 are displayed with letters from a to f or A to F respectively.
Every character of a HEX number expands into a binary code of four 0:s (zeroes) and 1:s (ones) as
given in table 9. Four successive characters thus expand into four times four binary numbers. Here's
an example:
We have a HEX number F3A1. We expand the number into a binary code so that we first take the four
binary digits that correspond to F, which are 1111. Then we write the four binaries that correspond to
3 (0011) after the first four. We now have 11110011. And so on.
Eventually, we have a string of 16 binary numbers, so called bits. HEX number F3A1 corresponds to a
binary code of 1111 0011 1010 0001. Spaces are added here for legibility and to visualize the fact
that every group of four bits corresponds to one HEX character.
The bits in a binary number are numbered from right to left always starting from 0 as follows:
1
1
1
1
0
0
1
1
1
0
1
0
0
0
0
1
With this information and the proper table of status fields you can translate a HEX status code into
actual status messages. For the tables of status fields see section ”Tonometry” or ”BIS” . If a bit is 1,
this means that the corresponding status/error condition is valid, whereas a 0 means that it is not.
Table 15
HEX to binary conversion
HEX
binary
HEX
binary
0
0000
8
1000
1
0001
9
1001
2
0010
A
1010
3
0011
B
1011
4
0100
C
1100
5
0101
D
1101
6
0110
E
1110
7
0111
F
1111
A-1
Document no. M1031519-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
A-2
Document no. M1031519-01
Datex-Ohmeda
S/5TM Compact Anesthesia Monitor,
F-CM1 (Rev. 04), F-CMREC1 (Rev. 01); Display Unit
S/5TM Compact Critical Care Monitor,
F-CMC1 (Rev. 04), F-CMCREC1 (Rev.01); Display Unit
Software License, L-CANE05/A
Software License, L-CICU05/A
Technical Reference Manual
All specifications are subject to change without notice.
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
Document no. M1031520-02
March, 2006
Datex-Ohmeda Inc.
P.O. Box 7550
Madison, WI 53707-7550, USA
Tel: +1 608 221 1551
Fax: +1 608 222 9147
GE Healthcare Finland Oy
Helsinki, Finland
P.O. Box 900
FI-00031 GE, FINLAND
Tel: +358 10 39411
Fax: +358 9 1463310
www.gehealthcare.com
Copyright  2006 General Electric Company
Table of contents
Table of contents
Table of contents
i
Table of figures
iii
Introduction
1
1
Specifications
1.1
1.2
1.3
1.4
1.5
1.6
1.7
2
Display Unit functional description
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2
S/5 Compact Monitor, F-CM1, F-CMREC1, F-CMC1, F-CMCREC1; Display Unit . . . . . . . . . . . . . . . . . . 2
LCD Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MemCard option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Network option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Wireless LAN option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Recorder option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Digital outputs of Display Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4
CPU section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1.1
Standby and Display Unit power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1.2
Watchdogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1.3
SRAM MT48T37V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
UPI section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.1
Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.2
CPU Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.3
Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.4
Serial Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Software License, L-CANE05, L-CANE05A, L-CICU05, L-CICU05A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Display controller section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.1
Display memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.2
Display controller resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MEM section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5.1
Memory Card interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5.2
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
NET section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.6.1
Ethernet interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Front Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.8.1
Backlights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.8.2
Connector board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.8.3
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Display Unit DC/DC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connectors and signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.10.1 External connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.10.2 Serial data interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.10.3 Digital and analog outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.10.4 Printer connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
i
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3
Service procedures
3.1
3.2
3.3
3.4
4
5
General service information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.2.1
Recommended tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.2.2
Recommended parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.2.3
Before beginning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.2.4
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.2.5
Functional inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Disassembly and reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
3.3.1
To disassemble the Display Unit F-CM(C)1 rev.04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
3.3.2
To disassemble the Display Unit of F-CM(C)(REC)1 rev.00...03 . . . . . . . . . . . . . . . . . . . . . .35
3.3.3
To remove the Central Processing Board (CPB) from the Display Unit Back Unit . . . . . . . . .36
3.3.4
To remove the Display Unit DC/DC power board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
3.3.5
To remove the Synchronization Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
3.3.6
To remove the Net Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
3.3.7
To remove the loudspeaker and fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
3.3.8
Disassembling the Connector Board and Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
3.3.9
To Disassemble the LCD Display Element, F-CM(C)(REC)1 rev. 00 . . . . . . . . . . . . . . . . . . . .37
3.3.10 To Disassemble the LCD Display Element, F-CM(C)(REC)1 rev.01, F-CM(C)1 rev.02...04 .38
3.3.11 Changing the LCD backlights, F-CM(C)(REC)1 rev.00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.3.12 Changing the LCD backlights, F-CM(C)(REC)1 rev.01, rev.02 . . . . . . . . . . . . . . . . . . . . . . . .39
3.3.13 Changing the LCD backlight, F-CM(C)1 rev.03 and rev.04. . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.3.14 Handling and storage of LCD Display component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.3.15 Downloading the software on empty Central Processing Board . . . . . . . . . . . . . . . . . . . . . .40
3.3.16 Performing Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Adjustments and calibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Troubleshooting
4.1
4.2
4.3
4.4
4.5
20
42
General (Display Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Software License (service software) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Memory Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Troubleshooting for the NET section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Earlier revisions
46
Appendix A: Service check form, S/5 Compact Anesthesia Monitor, S/5 Compact Critical Care
Monitor
A-1
ii
Document no. M1031520-02
Table of figures
Table of figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Compact Anesthesia Monitor................................................................................................................ 1
Basic structure of Display Unit .............................................................................................................. 4
Central Processing Board Block Diagram .............................................................................................. 6
UPI Section Block Diagram ................................................................................................................... 7
Display Controller Block Diagram .......................................................................................................... 9
Memory Section Block Diagram .......................................................................................................... 10
Central Processing Board, block diagram ............................................................................................ 11
Central Processing Board parts ........................................................................................................... 13
External connections of Compact Monitor frame F-CM(C)1 rev.04 ........................................................ 15
External connectors of Compact Monitor Frame rev.00...03 ................................................................. 16
iii
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
iv
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
Introduction
This section provides information about the maintenance and service of the following products:
•
S/5™ Compact Anesthesia Monitor F-CM1 Display Unit and S/5™ Compact Critical Care
Monitor F-CMC1, Display Unit (including UPI function, LCD display, Command board function,
Display Controller function, NET function, MEM function, DIS function, Display Unit power
supply unit) or S/5™ Compact Anesthesia Monitor F-CMREC1 Display Unit and S/5™ Compact
Critical Care Monitor F-CMREC1 Display Unit (in addition to above mentioned parts also a
built-in recorder).
•
Software Licenses L-CANE05/A, L-CICU05/A.
All the service menus related to the monitor are described in a separate “Service Menu” slot and the
spare part lists in “Compact Monitors Spare Parts” slot.
Figure 1
Compact Anesthesia Monitor
1
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1
Specifications
1.1 S/5 Compact Monitor, F-CM1, F-CMREC1, F-CMC1, F-CMCREC1;
Display Unit
Display Unit Dimensions,
DxWxH
Weight
Electrical Requirements
Power supply
Stability
Power consumption
Battery operation
Grounding
Interruptibility
Environmental Requirements
Operating temperature
Storage temperature
Humidity
1.2
Resolution
10 - 35 °C / 50 - 95 °F
-10 - 50 °C / 14 - 122 °F
10-90% non-condensing
12.1 in (diagonal)
Active Matrix Color
TFT LCD
SVGA 800x600
MemCard option
MemCard capacity
Data storage capacity
Operating system
File system
MemCards
1.4
10…17 VDC (supplied by Frame Unit VBUS voltage)
±10% of nominal voltage
27.5 VA, max. 2 A
up to 1.5 hour
Hospital grade
Data memory and alarm settings are
saved up to 15 minutes after monitor standby
LCD Display
Display size
Display type
1.3
55 x 335 x 270 mm (2.2 x 13.2 x 10.6 in)
<4 kg (9 lb.)
6 MB minimum
2 days of continuous physiological data trends
Datalight ROM-DOS
MS-DOS compatible
PCMCIA-ATA compatible memory cards
Network option
Meets IEEE802.3 specifications (10BASE-T)
Hospital grade approved data transformer
Coding element interface
1.5
Wireless LAN option
Frequency range
Output power
Data rate
2
Document no. M1031520-02
2.4 to 2.5 GHz
100 mW
11 Mbps per channel (max.)
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
Data transmission
Roaming
Certificates
Encryption
WLAN adapter
1.6
Recorder option
Power consumption
Printer type
Print resolution
Paper width
Traces
Print speed
1.7
IEEE 802.11b compliant,
Direct Sequence Spread Spectrum (DSSS)
Automatic roaming between the Datex-Ohmeda Central's
Access Points
Wi-Fi certified
Wired Equivalent Privacy (WEP) 40 and 128 bit
PC card type with antenna
3W
Thermal array
Vertical 8 dots/mm (200 dots/inch)
Horizontal 32 dots/mm (800 dots/inch)
at a speed of 25 mm/s and slower
50 mm, printing width 48 mm
Selectable 1, 2, or 3 traces
1, 6.25, 12.5, 25 mm/s
Digital outputs of Display Unit
Nurse call
Defibrillation Synchronization
Serial Output
Low State: 0-0.8V; High State: 2.8-5V
Generated on red and yellow alarms
State 0: 0-0.8V; state 1: 2.8-5V
Delay (max): 35 ms from R peak
Signal active time 10 ms
Asynchronous
Serial data interface, uses RS-232 standard
Baud rate max 115.2 kbps
Parity: None; Data bits: 8; Stop bit: 1
3
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2
Display Unit functional description
The Compact Monitor Display Unit includes the following parts:
•
Central Processing Board (CPB): includes Display Controller, UPI, CPU and optionally Network
and MemCard functions
•
•
•
•
•
Color LCD display and its backlight inverter
Connector board
Command board
Display Unit DC/DC power supply
Fan and loudspeaker
Inverter
Connector
Board
Keypad
Figure 2
2.1
Keypad
Basic structure of Display Unit
CPU section
The CPU section takes care of the central processing.
The main features are:
•
•
•
•
•
•
486 processor
Internal clock frequency 100 MHz
32 Mbytes DRAM
8 Mbytes program flash memory
32 Kbytes static RAM with real time clock
4 channel UART:
•
4
Document no. M1031520-02
2 serial channels with signals in AC-logic level
Net
Unit
display_basic_structure.vsd
Backlight
CPU BOARD
Sync.
Unit
12,1"
Display
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
•
•
•
2.1.1
2 serial channel signals in RS232-level
Programmable alarm sound generator
PC-card slot for software updates
Standby and Display Unit power down
When the monitor is turned to standby, NMI-interrupt is generated by the control logic. The interrupt
signal in the Central Processing Board means that all the outputs from the CPB are switched off (i.e.
display, alarm leds, etc.). The CPU section processor enters the HALT state.
During the Halt state the DRAM refreshing cycle continues to occur, thus saving trend and patient
data and user settings stored in the DRAM. After 15 min. the Power Management Board (in the Frame
Unit) cuts of the Display Unit voltage.
If the monitor is restarted within 15 min. of the last power off, a Warm Start is performed (trends and
temporary settings will be available). If the monitor is restarted after 15 min. of the last power off, a
Cold Start is performed (trends and temporary settings will be erased).
2.1.2
Watchdogs
There are certain watchdog functions to ensure the monitor’s performance. The UPI interrupts the CPU
continuously in order to tell that everything runs smoothly. If this watchdog fails, the UPI section is
initialized. The monitor is not reset.
The CPU section has its own watchdog in order to ensure that the main software functions normally. In
software overload situation the watchdog is not refreshed, and the monitor is reset.
The Central Processing Board (the CPU section) communicates with the Power Management Board in
the Frame Unit. This communication is also used as a watchdog signal between CPB and PMB.
5
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Patient
Modules
MODULE-BUS
PCMCIA
Serial
Ethernet
Sound
UPI
Code
Memory
Chipset
DRAM
Display
Controller
486 LOCAL BUS
NonVolatile
Memory
Reset
Logic
Figure 3
2.1.3
Boot
Memory
486
Processor
Central Processing Board Block Diagram
SRAM MT48T37V
The lithium battery back-up is a 32 Kbytes static RAM with a real-time clock.
CAUTION
The IC contains a lithium battery. Discard the battery according to local
regulations.
6
Document no. M1031520-02
display_central_proc_diagr.vsd
CPU BUS
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
2.2
UPI section
The UPI functions as a general I/O section. It performs I/O duties assigned to it by the CPU. The main
processor and the processor on the UPI communicate through a dual-port memory (shared RAM)
which is located on the UPI section.
2.2.1
Functional Blocks
The UPI section contains the CPU bus interface, a processor, program and dual-port memories, I/O
block, and serial bus interface.
2.2.2
CPU Bus Interface
The UPI section is connected to the CPU section by CPU (ISA) bus. The following signals pass between
the UPI and CPU: data bus, address bus, reset, write and read signals.
2.2.3
Processor
The processor of the UPI section is a Hitachi H8S/2655, which functions at 16 MHz frequency.
Serial Bus Interface
The serial bus interface of the UPI section contains Module Bus RS485, serial RS232 and RS422
interfaces.
Central Processing Board
Voltage
Meas
Shared
SRAM
CPU BUS
Control
Logic
UPI-BUS
Temp
Meas
Analog & Digital outputs
UPI
Processor
Module Bus
DIS-Bus
ComWheel Interface
Keypad Interface
Figure 4
display_upi_diagr.vsd
2.2.4
UPI Section Block Diagram
7
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.3
Software License, L-CANE05, L-CANE05A, L-CICU05, L-CICU05A
L-CICU05/L-CICU05A software is developed for critical care monitoring and L-CANE05/L-CANE05A
is for anesthesia monitoring. Anesthesia record keeping capability is included in the anesthesia
monitor software L-CANE05/L-CANE05A as standard. The software L-CANE05A and L-CICU05A
include extended arrhythmia analysis.
L-CANE05/L-CANE05A/L-CICU05/L-CICU05A is a license software. The license agreement that is
delivered with the software should be archived in a secure location. A relevant license number may
have to be referred when contacting GE Healthcare service/support. The license number is needed
also for future software upgrades.
Each of the above listed monitor software is loaded on a Central Processing Board at the factory,
i.e. they are not available separately.
The L-xxx05(A)S software is used for service purposes only and is stored on a separate Software Card
(PCMCIA, 8 MB). See section “Downloading the software on empty Central Processing Board”.
The U-xxx05(A) software is used for upgrade purposes and is stored on a separate Software Card
(PCMCIA, 8MB). See section “Downloading the software on empty Central Processing Board”.
CAUTION
2.4
The software card is not write protected. For safety reasons do not use software cards
for any other purpose, or on any other platforms than they are designed for.
Display controller section
The display controller is integrated to the Central Processing Board. The processor on the CPU section
transmits graphics information through the CPU bus to the display memory on the Display Controller
section.
The Display Controller section supports SVGA resolution. The resolution is automatically selected for
the LCD display in use. The resolution is set to 800 x 600.
2.4.1
Display memory
The Display memory contains digital display data. The size of the memory is 1 Mbyte making an 800 x
600 display resolution with 256 colors possible. The memory consists of a 1Mbyte DRAM.
2.4.2
Display controller resolution
The resolution of the display controller is set to SVGA, i.e. 800x600 resolution.
8
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
Central Processing Board
Figure 5
VGA
Controller
Flat Panel
Interface
display_contrllr_diagrm.vsd
486 LOCAL-BUS
DRAM
Memory
Display Controller Block Diagram
2.5
MEM section
2.5.1
Memory Card interface
The memory interface consists of a PD6722 controller and two PCMCIA compatible card sockets.
Both sockets consist of 60 signal and 8 power connections. The controller communicates with the
CPU. Card insertions and removal are also detected by the controller.
The MemCards are PCMCIA-ATA compatible. The MemCard files are MS-DOS compatible, and they
can be copied for archiving with any MS-DOS compatible computer equipped with PCMCIA-ATA
specification compatible card drive.
The MemCard function is optional. The operation requires a software option.
The monitor software can be downloaded to the monitor Flash memory through the memory interface.
2.5.2
Power supply
The memory section receives its power (+5V, +12V) from the CPB. PCMCIA card programming voltage
is +12V. The card programming voltage is controlled by the interface controller.
9
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Figure 6
2.6
PCMCIA
Controller
display_mem_sec_digrm.vsd
PCMCIA
SLOTS
CPU BUS
Voltage
switch
Memory Section Block Diagram
NET section
The Ethernet interface controller is basically the heart of the NET section. The interface controller
communicates with the CPU section through the CPU bus. The section also contains a 4k SRAM
memory.
The network interface controller transmits data packets to the Datex-Ohmeda Network and receives
data packets from the network through the 10BASE-T transformer. The transformer filters and
transforms the data and also provides the isolation.
The Ethernet status LEDs indicate the status of the network communication. The status LEDs are
controlled by the network controller. The LEDs are located on the Central Processing Board.
The PLD interfaces the coding element. The coding element contains information on the monitor
location. The network address and the monitor location information are transmitted to the CPU
section directly through the CPU bus.
10
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
Central Processing Board
Ethernet
Controller
Serial
EEPROM
ID-PLUG
Interface
Figure 7
2.6.1
10BaseT
ID-PLUG
display_cntrl_proc_brd_digrm.vsd
CPU BUS
CPU BUS
SRAM
Memory
Central Processing Board, block diagram
Ethernet interface
The data transformer is designed by Datex-Ohmeda and it is hospital grade approved.
Adapter’s 10BASE-T is an interface with low-pass filters on the unisolated side of the transformer. On
the isolated side there is a common mode choke for both transmitting and receiving lines.
The three LEDs on the board, which are not seen from the outside, indicate the following things:
activity on the network, collision detection and a good link in 10BASE-T interface.
The activity LED flashes when communication packets are detected in the Datex-Ohmeda Network.
The collision detection LED indicates a packet collision on the network. The collision detection LED
should flash only occasionally, otherwise there may be a physical layer problem. The good link LED
indicates whether or not the communication link to the HUB is functional. The good link LED should
always be lit.
11
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.7
Wireless LAN
Datex-Ohmeda Wireless Network is an extension to, or an alternative for, a wired Datex-Ohmeda
Network. It provides same network services than the wired Datex-Ohmeda Network.
The monitor network is a local area network based on standard Ethernet technology. The monitor
network is formed by connecting one Central and up to 32 bedside monitors together.
The Central and the bedside monitors are connected to a 10 Mbps hub. The hub works as a multiport
repeater and controls the information flow between all the devices connected to the monitor network.
The communication protocol for the monitor network is Datex-Ohmeda specific.
Wireless bedside monitors can use both the wired and wireless network. If the network cable is
connected, the wired Datex-Ohmeda Network is used.
For using Wireless LAN connection, the monitor requires Symbol24 Wireless LAN antenna card.
For configured parameters please refer to the Datex-Ohmeda Network, Wireless LAN Installation
Guide.
12
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
Patient
Modules
MODULE-BUS
PCMCIA
Serial
Ethernet
Sound
UPI
Code
Memory
Chipset
DRAM
Display
Controller
486 LOCAL BUS
NonVolatile
Memory
Reset
Logic
Figure 8
2.8
Boot
Memory
486
Processor
display_central_proc_diagr.vsd
CPU BUS
Central Processing Board parts
Front Unit
NOTE: The LCD display backlight circuit runs on a high voltage. Do not touch the inverter board or
the backlight tube leads when powered.
Front Unit includes an LCD display component, Inverter Board, Connector board and Keyboard.
The Front Unit is connected to the Central Processing Board with two cables: video signal cable and
Connector Board cable. The video signal cable transmits the video signal from the CPB to the LCD
display. Video signalling between the Display Controller on the CPB and the Front Unit is analogic.
Backlight power, keyboard and ComWheel signals are routed through the Connector Board Cable.
13
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.8.1
Backlights
The backlight consists of two replaceable cold-cathode fluorescent tubes driven by a separate
inverter board.
2.8.2
Connector board
The connector board is used for connecting the backlight power, keyboard and ComWheel signals
between the Central Processing Board and the Front Unit.
2.8.3
Keyboard
There are two keyboards in the Display Unit Front Unit: front panel and side panel keyboards. The
keyboards are foil membrane keypads. There is no separate processor for the keyboards. The
keyboards are connected to the UPI section of the Central Processor Board through Connector Board.
2.9
Display Unit DC/DC power supply
This DC/DC converter board transforms primary voltage of between +10 and +18 VDC to +3.3V, +5V,
and +12 V secondary voltages. All the output voltages have common ground.
The DC/DC power supply is powered by Vbus voltage generated by the Frame Unit AC/DC converter
(mains). If the mains power fails, the DC/DC power supply is powered by batteries.
Turn-on and shut-down sequences of the DC/DC power supply are controlled by a logic on the DC/DC
board and by the Central Processor Board software. If overvoltage occurs at an output line, the
converter turns itself off automatically.
The Display Unit DC/DC converter supplies also a Display Unit fan.
14
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
2.10 Connectors and signals
2.10.1 External connectors
9
1
11
10
12
2
3
4
14
8
5
13
6
7
Figure 9
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
External connections of Compact Monitor frame F-CM(C)1 rev.04
Air filter
NET connector
NET ID connector (not used with N-CMW)
Recorder (optional)
SYNC connector
Connector for external keyboard (anesthesia record keeping solution keyboard), K-CREMCO or
Barcode Reader
Potential equalization
Serial port
Receptacle for power cord
WLAN PC card LED
WLAN PC card
Slot for Memory Cards (PCMCIA) and WLAN PC card
Connector for Device Interfacing Solution
Modules
NOTE: Insert the WLAN PC card in the first PC card slot from the front.
15
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
11
11
1
10
9
14
13
2
12
8
3
4
5
7
6
Figure 10
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
External connectors of Compact Monitor Frame rev.00...03
Dust filters
Recorder unit (optional)
Connector for factory use only
Synchronization connector
Connector for external keyboard (anesthesia record keeping solution keyboard), K-CREMCO or
Barcode Reader
Potential equalization connector
Serial port connector
Receptacle for power cord
NET ID connector
NET connector
WLAN antenna cover (optional)
Connector for Device Interface Solution
WLAN antenna card LED
WLAN antenna card (optional)
16
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
DIS connector, X5 DIS interface
RS422 connector
Pin No.
Signal
1
2
3
4
5
6
7
8
DIS_out +
DIS_out 15V_DIS
GND
8V_DIS
GND
DIS_in +
DIS_in -
Pin No.
Signal
1
2
3
4
5
6
7
8
Tx +
Tx Rx +
N/C
N/C
Rx N/C
N/C
Pin No.
Signal
1
2
3
4
5
6
7
8
9
IDCS1 (chip select)
IDCL (clock)
IDDI (data in)
IDDO (data out)
IDPE (protect enable)
+5Vdc
Direct ECG
Nurse call
GND
Network connector, X5
RJ45 connector
1 2 3 4 5 6 7 8
Coding element connector, X4
9 pin female D-connector
5
1
9
6
Direct ECG (pin 7)
Delay (max.): 15 ms
Gain ECG (in)/ECG (out): 1 mV/1V
NOTE: The direct ECG out signal is not available with modules M-ESTP rev. 01, M-EST rev. 00 and
M-ETP rev. 00.
Nurse call (pin 8)
The nurse call signal is generated by the red and yellow alarms. When activated, the signal is set to
the high state and remains at the high state until the alarm situation is over or the SILENCE ALARM
key is pressed. The high state range is from 2.8 to 5 V, while the low state range is from 0 to 0.8 V.
If the output signals are used simultaneously with the coding element, a B-UPINET Y-cable (order
number 889308) should be used.
17
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Keyboard connector, X9
5 pin connector
Pin
Signal
1
2
3
4
5
KB_CLK
KB_DATA
not in use
GND
+4.75 - +5.25V
Pin No.
Signal
1
2
3
4
GND
Def_Sync
Direct ECG
Pressure Out
Synchronization connector, X8
4 pin female connector
Direct ECG (PIN 3):
Delay (max.): 15 ms
Gain ECG (in)/ECG (out): 1 mV/1V
NOTE: The direct ECG out signal is not available with modules M-ESTP rev. 01, M-EST rev. 00 and
M-ETP rev. 00.
Pressure out (PIN 4):
P1 from hemodynamic module
Gain Signal (out) / Pressure (in): 1V/100 mmHg
Pressure area 0…300 mmHg
RS232 Serial data connector X11
9 pin male D-connector
18
Document no. M1031520-02
Pin No.
Signal
1
2
3
4
5
6
7
8
9
GND
RxD
TxD
NC
GND
N/C
RTS
CTS
N/C
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
2.10.2 Serial data interface
The serial interface is an asynchronous RS-232 connection, which uses hardware flow control. The
communication speed is 115.2 kbps. The communication uses the following parameters: Parity
None, Data bits 8 and Stop bits 1.
2.10.3 Digital and analog outputs
Digital outputs
There are separate digital outputs. Both signals use TTL level. The outputs are: Defibrillation Sync.
and Nurse Call.
The Defibrillation Synchronization Signal is obtained from Synchronization connector X8, pin 2.
The Nurse call is obtained from Coding element connector X4, pin 8.
Defibrillation Sync indication is generated by ECG. When active, the signal is in state 1. After 10 ms
the signal is reset to state 0. New Defibrillation Sync is not generated before the indication is
deactivated. The delay from the R wave peak to the start of the signal is maximally 35 ms.
Nurse Call indication is generated by red and yellow alarms. When activated, it is set to state 1 and
remains at that state until the alarm situation is over or SILENCE ALARM key is pressed.
The range of state 0 is from 0 to 0.8 V, and the range of state 1 is 2.8 to 5 V.
Analog outputs
Compact Anesthesia/Critical Care Monitor produces two analog real-time signals. The Direct ECG
signal is available in Coding element connector X4 pin 7 and Synchronization connector X8, pin 3.
The other signal is Invasive pressure output. It is available in Synchronization connector X8 pin 4.
NOTE: When the source of the selected analog output becomes invalid (for example, transducer is
disconnected), the last valid waveform information remains on the output and the numerical
information is no longer valid.
Direct ECG
Delay (max.): 15 ms
Gain ECG (out)/ECG (in): 1 V/1 mV
NOTE: The direct ECG out signal is not available with modules M-ESTP rev. 01, M-EST rev. 00 and
M-ETP rev. 00.
Invasive pressure signal: P1
Delay (max.): 25 ms
Gain Signal (out) / Pressure (in): 1V/100 mmHg
Pressure area 0…300 mmHg
The Invasive pressure output signal is 1 V/100 mmHg, originally ranging from 0 to 300 mmHg, and
with a delay of approximately 25 ms. The signal requires an input impedance of 100 k.
2.10.4 Printer connection
For connecting a printer to the monitor, the serial data interface is used. When parallel printing is
desired, a serial to parallel converter (ref. 78030) is needed.
For further information see Part I, Interfacing.
19
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3
Service procedures
3.1
General service information
The field service of the S/5 Compact Anesthesia Monitor and S/5 Compact Critical Care Monitor is
limited to replacing faulty PC boards and mechanical parts. Return the faulty PC boards to GE
Healthcare for repair.
GE Healthcare is always available for service advice. Please provide the unit serial number, full type
designation and a detailed fault description.
CAUTION
3.2
Only trained personnel with appropriate tools and equipment shall perform the tests
and repairs outlined in this section. Unauthorized service may void the warranty of the
unit.
Service check
S/5 Compact Anesthesia Monitor, F-CM(REC)1
S/5 Compact Critical Care Monitor, F-CMC(REC)1
Display Unit
These instructions include complete procedures for a service check. The service should be performed
after any service repair. Additionally, the service check procedures can also be used for determining
possible failures.
The procedures should be performed in ascending order.
The instructions include a check form (“APPENDIX A”), which should be filled in when performing the
procedures.
The symbol
" in the instructions means that the check list should be signed after performing the
procedure.
3.2.1
Recommended tools
Tool
Order No.
Notes
Power cord
Screwdrivers
MemCard - Menu
for MemCard Option
MemCard - Data
for MemCard Option
Anaesthesia Keyboard, K-ARKB
K-ARK interface cable
Hemodynamic Module
20
Document no. M1031520-02
881154
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
3.2.2
3.2.3
Recommended parts
Part
Order No.
Display Unit Fan filter
897010
Recorder paper
74205
Notes
for recorder unit
Before beginning
•
•
•
•
•
Make sure that the monitor is switched to standby.
Disconnect the power cord and press the service reset switch until the LED next to it turns off.
If the monitor is connected to the Datex-Ohmeda Network, disconnect the Mon-Net cable from
the Frame Unit. Take out any memory cards, if installed.
Detach the Display Unit from the Frame Unit.
Open the Display Unit by detaching the Front Unit.
NOTE: Wear a static control wrist strap when handling PC boards. Electrostatic discharge may
damage components on the board.
3.2.4
Visual inspection
1.
DC/DC power supply board
Disconnect the DC/DC power supply board. Check the Display Unit – Frame Unit connector
under the board:
•
•
screws are tightened properly
the connector is clean and intact
"
2.
Central Processing Board
Check the Central Processing Board in the Display Unit:
•
•
•
screws are tightened properly
cables are connected properly
all ICs that are on sockets are attached properly
"
3.
DC/DC power board
Reconnect and check the DC/DC Power Board:
•
•
•
screws are tightened properly
all connectors are clean and intact
the cables are attached properly
"
4.
Net Unit and Synchronization Unit
Check that:
21
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
•
•
screws are tightened properly
the connector pins are intact
"
5.
Front Unit
Check that:
•
the Connector Board screws are tightened properly and the cable connectors are clean
and intact
•
the Inverter Board screws are tightened properly and the cable connectors are clean and
intact
•
•
the Backlight cables are intact and attached properly
•
the Connector Board foil cable is intact and attached properly to the connector on the
Central Processing Board
the keyboard foil cables are intact and attached properly to connectors on the Connector
Board
•
the video signal foil cable is intact and attached properly to its connector on the Central
Processing Board
Reattach the Front Unit.
"
6.
External parts
Check external parts of the Display Unit:
•
•
•
•
all stickers are intact
the LCD display screen is intact
the ComWheel cover is intact and attached properly
all mechanical parts are functioning properly
Connect the Display Unit to the Frame Unit.
"
7.
Inserting module
Check that the module used goes in smoothly and locks up properly in both module slots.
Leave the module connected.
"
8.
Fan filter
Clean or replace the Display Unit fan filter.
"
22
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
3.2.5
Functional inspection
9.
Stand-by LED
Connect the power cord.
Check that the standby LED starts blinking or is on continuously, if the batteries do not need
charging.
"
10. Start-up
Switch the monitor on.
Check that the monitor starts up properly, i.e. the alarm LEDs turn blank, the start-up sound is
heard from the loudspeaker and the normal monitoring screen appears.
No error messages should appear on the screen.
If the monitor contains the recorder unit, two lines of start-up information should be recorded.
"
11. Monitor screen configuration
Configure the monitor screen so that all the needed parameter information is shown:
Monitor Setup
Screen 1 Setup
Waveform Fields
Digit Fields
Check that the selected parameter information is shown on the screen.
NOTE: InvBP waveforms are not shown without a patient simulator. Do no connect the simulator to the
monitor at this stage.
"
12. Mark Event or Take Snapshot
Push the menu keys Help and Mark Event, or Take Snapshot.
Check that the picture on the LCD display screen is straight, clear and stable.
"
13. Time and date
Check that the time and date are correct, adjust them if necessary.
Monitor Setup
Set Time and Date
NOTE: The selection SET TIME AND DATE cannot be accessed if a case is started, or a patient has
been admitted.
NOTE: If the clock shows time 0:00 continuously (at successive start-ups), the SRAM/TIMEKEEPER
battery needs to be replaced.
23
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
The FACTORY RESET should be performed after the battery replacement, see “Performing
Factory Reset” .
"
14. Loudspeaker
Check the loudspeaker by setting the alarm sound:
Alarms Setup
Alarm Volume
Test the whole volume scale from 1 to 10 by turning the ComWheel and check that the alarm
volume changes correspondingly. The alarm sound should be clear and audible with all the
settings.
"
15. Display brightness
Check the display brightness control:
Monitor Setup
Display Brightness
Press the ComWheel and check that the display brightness follows the selected brightness.
"
16. Monitor software
Enter the service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Take down the information regarding Monitor and Power Management Board software.
"
17. Content of service log
Select Service Log from the menu.
Check the contents of the Service Log for possible problems. If the monitor contains the
recorder unit, record the Service Log on the recorder by selecting Record Log.
"
18. Power supply output voltages
Check the power supply unit output voltages through the service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Frame
Power Supply
The Display Unit voltages should meet the following ranges:
24
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
+12V
11.50...12.50 V
+3.3 V
3.00...3.60 V
Vbus
10.00…17.00V
Depends on the power source
"
19. Watchdog circuitry
Test the watchdog circuitry:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Set/Test
Perform the tests WATCHDOG and WD BY OVERLOAD. Check that the monitor restarts in each
case.
NOTE: When selecting WD BY OVERLOAD, restarting should take place approximately after
15 seconds.
"
Preset monitor settings:
Record/Print
Record Waveforms
Waveform 1 --> ECG1
Waveform 2 --> P1
Waveform 3 --> P2
Delay --> Off
Paper Speed --> 6.25 mm/s
Length --> 30 s
20. Alarm LEDs
Enter the Keyboard service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Keyboard
Select the text Upper Led. Check that the red alarm LED(s) is turning on and off when pressing
the ComWheel. Check also the yellow alarm LED(s) by selecting Lower Led from the menu.
"
21. Membrane keys check
Press the keys on the monitor command board one by one. Check that each key generates a
sound from the loudspeaker. Also, the corresponding text in the menu should change from
yellow to red.
25
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Check also the functioning of the side panel keys.
"
22. ComWheel check
Turn the ComWheel clockwise and counter clockwise and check that each step generates a
sound from the loudspeaker and the corresponding values at the bottom of the menu increase.
Select Dummy Press. Press the ComWheel and check that the press generates a sound and the
corresponding value in the menu increases.
"
23. K-ARK connector
Check that the command board section of the Anesthesia Keyboard functions normally through
the K-ARK connector.
"
24. Module communication
Connect a patient simulator to the module.
Enter the ESTP: ECG service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Parameters
ESTP: ECG
Check that the Timeouts, Bad checksums and Bad c-s by mod values do not increase faster
than by 5 per second.
Change the module into the other slot. When the module is recognized, check that the values do
not still increase faster than by 5 per second.
"
25. Battery
Enter the Battery service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Frame
Power Supply
Battery
Check that the information on the page is correct.
"
26
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
26. Battery voltage
Check that the shown Battery Voltage value is within 10 – 17V.
"
27. Monitor temperature
Check that the shown Monitor Temperature value is within 20 - 40.
"
28. Battery operation
Disconnect the power cord (without switching the monitor to standby).
Check that the monitoring continues normally. The battery indicator should appear in the upper
right hand corner of the screen.
"
29. Reconnecting the power cord
Reconnect the power cord.
Check that the monitoring continues without problems. The battery indicator should be
replaced by the text CHARGE.
"
Recorder Unit
30. Cover open recognition
Open the recorder unit cover. Check that the message ‘Recorder: Cover open’ appears on the
screen, then close the cover.
"
31. Recording
Press the key Record Wave and check that the module starts recording the selected
waveforms. Press the key Stop on the module to stop recording.
NOTE: InvBP waveforms are not recorded without a patient simulator.
NOTE: If no recording appears, check that the paper roll is installed in a correct way. Only one side of
the paper is printable.
"
32. Paper speed
Press the key Record Wave again and this time wait until the recording stops. Check that the
length of the recorded waveform scale is 18.7 cm (± 1.5 cm).
Change the paper speed setting to 1 mm/s:
27
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Record/Print
Record Waveforms
Paper Speed --> 1 mm/s
Press the key RECORD WAVE and wait until the recording stops. Check that the length of the
scale is now 3.0 cm (± 0.5 cm).
"
33. Quality of recording
Check that the quality of the recording is acceptable.
"
MemCard option
NOTE: The following steps are applicable only when the MemCard option is installed in the monitor.
34. Memory option recognition
Enter the Memory Card service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Frame
MemCards
Check that the memory option is recognized properly, i.e. Present and Active state YES.
"
35. Memories and PCMCIA controller test
Check that the Memory board memories and the PCMCIA controller have passed their tests. The
status for each should be OK.
"
36. Interface status
Select Communication. Check that Interface status states ACTIVE continuously and the error
counter values at the bottom part of the menu are stable.
"
37. Menu Card recognition
Select Module Status. Insert a Memory card labelled Menu in the left hand side memory card
slot. Check that the message ‘Menu Card inserted’ appears in the message field and the white
menu card symbol in the upper right hand corner of the screen within 1 minute.
NOTE: The battery symbol overrides the memory card symbols.
"
28
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
38. Card type recognition
Wait until the information regarding SLOT1 is fully updated in the service menu, then check that
the Card type states MENU and the File system states ATA.
Check that the rest of the information for SLOT1 is reliable and no errors have been detected.
"
39. Data Card recognition
Insert a Memory card labelled Data in the right hand side memory card slot. Check that the
message ‘Data Card inserted’ appears in the message field and the green menu card symbol on
the upper right hand corner of the screen within 1 minute.
Wait until the information regarding SLOT2 is fully updated in the service menu, then check that
the Card type states DATA and the File system states ATA.
Check that the rest of the information for SLOT2 is reliable and no errors have been detected.
"
40. Save and Load Modes
Enter the Save Modes menu:
Monitor Setup
Install Service (Password 16-4-34)
Save Modes (Password 13-20-31)
Save the current modes into the Menu card by selecting
Load Modes
To Memory Card --> Save.
Wait until the text ‘Saved’ appears, then return to the previous menu.
Change the name for the mode number 1:
Select the mode number 1, press the ComWheel and select -Name. Select suitable characters
from the list by turning and pressing the ComWheel, then confirm the new name by selecting
End.
Load the original modes from the Menu card by selecting
Load Modes
From Memory Card --> Load.
Wait until the text ‘Loading’ changes to ‘Loaded’ (may take a couple of minutes), then return to
the previous menu.
Check that the mode number 1 has got back its original name.
"
41. Data Card functions
Press the membrane key Display Trends or Pt.Data & Trends --> Trends. Check that there is
trend information available for the monitored parameters.
Erase the trends:
29
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Reset Case
Reset All --> Yes
or
Admit/Discharge
Discharge --> Yes
Check that the trends have been erased.
Reload the trends from the Data card by pressing the key Patient Data or Admit/Discharge,
selecting Patient from Card, pressing the ComWheel on the last saved file (the file information
is shown at the bottom of the menu) and selecting Load.
Wait until the message ‘Loading from Mem. Module’ disappears, then check that the original
trends are available again.
"
Network option
NOTE: The following steps are applicable only when the Network option is installed in the monitor.
42. Connection to Network
Check that the Mon-Net cable connector is clean and intact, then connect it to the network
connectors on the Frame Unit.
Check that the monitor connects to the Datex-Ohmeda Network, i.e. the network symbol
appears under the clock in the upper right hand corner of the screen. Also a message regarding
the connected Central should appear in the message field of the screen.
NOTE: The battery symbol overrides the network symbol in Compact Monitor.
If the message regarding the Central does not appear, check the status of the network.
"
43. Ethernet address
Enter the network board service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service - Frame (Password 26-23-8)
Network
Take down the monitor’s Ethernet address, which is shown beside the text Address.
44. Data counters
Check that the service menu counters for the received (‘In’) and transmitted (‘Out’) data are
updated frequently.
"
45. Data error counters
Check that the counters for data errors (CRC, Frame, Transm.) are stable.
30
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
NOTE: The counters may show values higher than 0. However, if any of the values is increasing
continuously, it indicates a problem.
"
46. Hardware error counters
Check that the counters for hardware errors (Intern., Missed, FIFO, Overrun) show all 0. If any of
the counters show a value higher than 0, replace the network board.
"
47. Disconnection recognition
Disconnect the Mon-Net cable from the Frame Unit. Check that the message ‘Network down:’
appears in the message field within 30 seconds. When the message appears, the service menu
values are no longer updated.
Reconnect the Mon-Net cable and check that the monitor connects to the Datex-Ohmeda
Network again.
"
48. ID-plug recognition
Switch the monitor to standby. Disconnect the Identification plug from the Frame Unit. Switch
the monitor back on and check that the message ‘Check network connectors’ appears in the
message field.
Reconnect the Identification plug and check that the monitor connects to the Anaesthesia
Network.
"
Wireless LAN option
49. Signal strength
Check that the green LED on the wireless antenna card blinks and the WLAN signal strength
symbol roams or stays fixed on the monitor screen.
"
50. Configure access point
Configure one access point appropriately. Bring the Compact Monitor to good WLAN coverage
area. Check that the field level indicator stops scrolling.
Go to the WLAN Status page (... Service -> Frame -> Network -> WLAN - WLAN Status).
Check that the Connection is active, AP MAC address is recognized and the connection speed is
at least 2 Mbits/s.
"
31
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
51. Connection to the Network
Make sure that the monitor's wireless LAN antenna card is in line of sight with a wireless LAN
access point antenna. Check that the monitor connects to the Datex-Ohmeda Network, i.e. the
wireless LAN network symbol appears in the upper right-hand corner of the screen.
"
General
52. Trend retaining
Check that the monitor is capable of storing the trend information and temporary settings in a
short (max. 15 minutes) standby.
Press the membrane key Display Trends or Pt.Data & Trends --> Trends. Check that there is
trend information available for the monitored parameters.
Switch the monitor to standby and disconnect the power cord. Wait for two minutes, then
reconnect the power cord and switch the monitor back on.
Check that the trend information is still available.
"
53. Service reset switch check
Switch the monitor to standby and disconnect the power cord. Press the service reset switch for
at least five seconds. Check that the LED next to the switch turns off, and also the fan turns off.
Reconnect the power cord and turn the monitor back on. Check that all trends have now been
erased.
"
54. Battery capacity
Test the batteries by performing the following:
•
•
•
•
detach all modules
keep the monitor connected to the mains power until the batteries are fully charged
install a Hemodynamic Module and disconnect the power cord
notice the time the monitor stays on with batteries
Replace the batteries, if the time was less than 45 minutes.
"
55. Service Log reset
Enter the Service Log in the service menu:
Monitor Setup
Install Service (Password 16-4-34)
Service (Password 26-23-8)
Service Log
Clear the content of the Service Log by selecting RESET LOG from the menu.
"
32
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
56. Electrical safety check
Perform an electrical safety check and a leakage current test.
Check that the monitor functions normally after the performed electrical safety check.
"
57. Final cleaning
Switch the monitor to standby, disconnect the power cord and perform final cleaning.
"
Fill in all necessary documents.
33
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.3
Disassembly and reassembly
WARNING
The S/5 Compact Anesthesia/ Critical Care Monitor is always energized by the
internal battery. A short circuit may cause internal damage. Do not touch any
exposed wiring or conductive surface inside, this may cause an electric shock.
CAUTION
Perform leakage current measurement whenever service or repair has been done in
the monitor.
NOTE: The backlight circuit runs on a high voltage. Do not touch the inverter board or the
backlight tube leads when powered.
3.3.1
To disassemble the Display Unit F-CM(C)1 rev.04
1.
2.
3.
4.
5.
Set the Compact Monitor lying on its rear side.
Turn the quick lock screw at the bottom of the Display Unit counter clockwise to release it.
Pull the Display Unit carefully upwards.
Set the Display Unit lying on its front side; be careful not to damage the ComWheel or the LCD
screen.
Open and detach the four screws with the washers at the corners of the Display Unit.
X5
X7
6.
7.
Lift the Display Unit carefully from the side of the unit (Note that the Front Unit is connected with
flat cables to the Central Processing Board). Detach the two flat cables from the CPB X7 and X5
connectors. Please note that the connectors are fragile; do not bend them while disconnecting
the cables.
Lay the Display Unit carefully on the table.
34
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
3.3.2
To disassemble the Display Unit of F-CM(C)(REC)1 rev.00...03
1.
2.
Set the Compact Monitor lying on its rear side.
Turn the quick lock screw at the bottom of the Display Unit counter clockwise to release it.
3.
4.
Pull the Display Unit carefully upwards and detach the Network and NetID cables.
Set the Display Unit lying on its front side; be careful not to damage the ComWheel or the LCD
screen.
Open and detach the four screws with the washers at the corners of the Display Unit.
5.
6.
7.
Lift the Display Unit carefully from the side of the unit (Note that the Front Unit is connected with
short flat cables to the Central Processing Board). Detach the two flat cables from the CPB X7
and X5 connectors. Please note that the connectors are fragile; do not bend them while
disconnecting the cables.
Lay the Display Unit carefully on the table.
35
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.3.3
To remove the Central Processing Board (CPB) from the Display Unit Back Unit
1.
2.
3.
4.
5.
6.
7.
8.
9.
3.3.4
Disassemble Display Unit.
Detach the fan and loudspeaker cables from the CPB, connectors X17 (loudspeaker) and X16
(fan).
Detach the power cables coming from the DC/DC board, connector X10.
Detach the Signal cables (two) coming from the DC/DC board, connectors X23 and X19.
Detach carefully the Synchronization board foil cable by opening the lock at the connector X9
and pulling the foil out.
Detach the NetID cable from the CPB, connector X8.
Detach the Network cable from the CPB, connector X20.
Open the seven screws holding the CPB.
Lift the CPB carefully from the Display Unit.
To remove the Display Unit DC/DC power board
1.
2.
3.
4.
5.
6.
Disassemble the Display Unit.
Detach the fan and loudspeaker cables from the CPB, connectors X17 and X16.
Detach the power cables leading to the CPB.
Detach the signal cables leading to the CPB.
Open the four screws holding the DC/DC power board.
Lift the DC/DC power board carefully from the Display Unit.
36
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
3.3.5
To remove the Synchronization Unit
1.
2.
3.
Disassemble the Display Unit.
Detach carefully the Synchronization board foil cable by opening the lock at the connector X9
and pulling the foil out.
Open the two screws holding the whole unit in the Display Unit back cover.
NOTE: Do not open the screws holding the Synchronization board in the Synchronization Unit.
3.3.6
To remove the Net Unit
1.
2.
3.
4.
3.3.7
Disassemble the Display Unit.
Detach the NetID and Network cables from the CPB, connectors X8 and X20 respectively.
Open the two screws holding the Net Unit in the Display Unit cover.
Open the two screws holding the ID connector in the Display Unit back cover (from the outer side
of the cover).
To remove the loudspeaker and fan
1.
2.
3.
Disassemble the Display Unit.
Detach the loudspeaker and fan cables from the CPB, connectors X17 and X16 respectively.
Open the screws holding the loudspeaker and fan.
NOTE: When reassembling, be sure to connect the cables to correct connectors on the PCB.
3.3.8
Disassembling the Connector Board and Inverter Board
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disassemble the Display Unit.
Set the Front Unit carefully lying with the LCD screen downwards. Note! Be careful not to
damage the LCD screen or the ComWheel.
Detach carefully the lower keyboard flat cable from the Connector Board.
Detach carefully the side panel keyboard flat cable from the Connector Board.
Detach the Connector Board – Inverter Board cable.
Detach the ComWheel cable.
Open the four screws holding the Connector board and remove it.
Detach the backlight cables from the Inverter Board.
Open the three screws holding the Inverter Board.
NOTE: The Inverter Board is sensitive to bending.
NOTE: When replacing the Inverter Board, fasten the inverter screws gently, using only as much force
as necessary to fasten the board firmly enough in place. The screws must not be fastened so tightly
that the board will be bent from around the screws. Also, do not bend or twist the Inverter Board
during the assembly.
3.3.9
To Disassemble the LCD Display Element, F-CM(C)(REC)1 rev. 00
NOTE: Wear a static control wrist strap and soft cotton gloves (dust free) when handling the LCD
display parts. Hold them by their corners or edges. Do not touch the connector pins.
37
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
In normal circumstances it is very difficult to keep the LCD Display component and the display shield
surfaces free of dust when the LCD Display unit package is opened and they are exposed to room air.
If dust particles remain on the LCD Display component and the display shield surfaces, they may
impair the picture quality on the screen.
In case you need to detach the LCD Display component for repair, you may return it to be repaired at
GE Healthcare. If you can provide a dustfree environment, follow the instructions below. See also
Exploded view of the Display Unit, Front Unit, F-CM(C)(REC)1 Rev. 00.
1. Disassemble the Display Unit.
2. Detach carefully the lower keyboard flat cable from the Connector Board.
3. Detach carefully the side panel keyboard flat cable from the Connector Board.
4. Detach the ComWheel cable.
5. Detach the backlight cables from the Inverter Board.
6. Open the four screws holding the LCD Display Unit and the metal EMC cover in the Display Unit
front cover.
7. Open the two screws covering the video flat cable connector in the LCD Display element.
8. Lift the EMC cover carefully up.
9. Lift the LCD Display element carefully up.
NOTE: Do not use excessive force when fastening the display component to the metal frame.
Fastening the screws too tightly might bend the display module too much and break it. The screws
must also be fastened gradually: first fasten all screws slightly, then more tightly.
NOTE: When reassembling the LCD Display component, be careful that no dirt or finger prints are left
between the LCD element and the protection glass window.
NOTE: If the LCD Display unit is broken, handle it carefully to avoid injury (the LCD Display component
and the backlight lamp(s) are made of glass). Wash your hands if you touched liquid crystal, which
may flow out from a broken LCD Display component.
NOTE: Do not touch, push or rub the exposed display module surface. Keep the surface clean. In case
of accidental mishandling, see the instructions following this chapter.
3.3.10 To Disassemble the LCD Display Element, F-CM(C)(REC)1 rev.01, F-CM(C)1 rev.02...04
NOTE: Wear a static control wrist strap and soft cotton gloves (dust free) when handling the LCD
display parts. Hold them by their corners or edges. Do not touch the connector pins.
In normal circumstances it is very difficult to keep the LCD Display component and the display shield
surfaces free of dust when the LCD Display unit package is opened and they are exposed to room air.
If dust particles remain on the LCD Display component and the display shield surfaces, they may
impair the picture quality on the screen.
In case you need to detach the LCD Display component for repair, you may return it to be repaired at
GE Healthcare. If you can provide a dustfree environment, follow the instructions below. See also
Exploded view of the Display Front Unit, F-CM(C)(REC)1 rev. 01, F-CM(C) rev 02.
1. Disassemble the Display Unit.
2. Detach carefully the lower keyboard flat cable from the Connector Board.
3. Detach carefully the side panel keyboard flat cable from the Connector Board.
4. Detach the ComWheel cable.
5. Detach the backlight cables from the Inverter Board.
38
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
6.
7.
8.
9.
10.
Open the four screws holding the metal EMC cover in the Display Unit front cover.
Open the two screws covering the video flat cable and ferrite in the LCD Display element.
Lift the EMC cover carefully up.
Open the four screws holding the LCD element in the Display Unit front cover.
Lift the LCD Display element carefully up.
NOTE: Do not use excessive force when fastening the display component to the metal frame.
Fastening the screws too tightly might bend the display module too much and break it. The screws
must also be fastened gradually: first fasten all screws slightly, then more tightly.
NOTE: When reassembling the LCD Display component, be careful that no dirt or finger prints are left
between the LCD element and the protection glass window.
NOTE: If the LCD Display unit is broken, handle it carefully to avoid injury (the LCD Display component
and the backlight lamp(s) are made of glass). Wash your hands if you touched liquid crystal, which
may flow out from a broken LCD Display component.
NOTE: Do not touch, push or rub the exposed display module surface. Keep the surface clean. In case
of accidental mishandling, see the instructions following this chapter.
3.3.11 Changing the LCD backlights, F-CM(C)(REC)1 rev.00
1.
2.
3.
Disassemble the Display Unit.
Detach the backlight cables from the Inverter Board.
Push the lid beside the backlight to release the backlight tube. Pull the backlight out.
NOTE: Do not bend the backlight tube.
NOTE: Do not touch the backlight tube with your hands.
3.3.12 Changing the LCD backlights, F-CM(C)(REC)1 rev.01, rev.02
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disassemble the Display Unit.
Detach carefully the lower keyboard flat cable from the Connector Board.
Detach carefully the side panel keyboard flat cable from the Connector Board.
Detach the ComWheel cable.
Detach the backlight cables from the Inverter Board.
Open the four screws holding the metal EMC cover in the Display Unit front cover.
Open the two screws covering the video flat cable and ferrite in the LCD Display element.
Lift the EMC cover carefully up.
Release the screw holding the backlight tubes in their place.
NOTE: The screw cannot be removed totally, only released.
10. Detach the backlight tube by sliding it to the left and then lift it up.
NOTE: Do not bend the backlight tube.
NOTE: Do not touch the backlight tube with your hands.
39
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.3.13 Changing the LCD backlight, F-CM(C)1 rev.03 and rev.04
Perform the steps 1-8 as in section 3.3.12. Changing the LCD backlights, F-CM(C)(REC)1 rev.01,
rev.02.
1. Detach the screw holding the backlight tube set in place.
2. Detach the backlight tube set by pulling it to the left.
NOTE: Do not bend the backlight tube.
NOTE: Do not touch the backlight tube with your hands.
3.3.14 Handling and storage of LCD Display component
Handling of LCD Display component and protective window
If the LCD Display component surface becomes dusty, wipe it gently with absorbent cotton, chamois
or other soft material. If necessary, breathe onto the display surface and wipe immediately. The
display surface may also be cleaned using a small amount of normal hexane. Do not use acetone,
toluene or alcohol because they cause chemical damage to the polarizer.
1. Wipe off saliva and water drops as soon as possible. Their prolonged contact with the polarizer
cause deformations and color fading.
2. Do not open the component case because internal circuits are sensitive to electrostatic
discharges.
Taking a spare part LCD Display component or a display shield into use:
Peel off the protective film slowly (in more than 10 seconds) from the display or protective window
surface. Fast peeling may generate enough static electricity to destroy the LCD Display component.
Storaging an LCD Display component as a spare part for a long period
1.
2.
Store the display in a dark place. Do not expose it to sunlight or fluorescent light. Keep the
temperature between 5 °C and 35 °C at normal humidity.
The polarizer surface should not come into contact with any other object. It is recommended
that the display unit is stored in the container in which it was originally shipped.
3.3.15 Downloading the software on empty Central Processing Board
In case of a faulty Central Processing Board refer first to chapter “To remove the Central Processing
Board (CPB) from the Display Unit Back Unit” and then follow the instructions for downloading service
software below.
NOTE: All user settings will be lost after downloading of a new monitor software.
NOTE: During the downloading of the software, the serial number of the monitor is written on the
software card. The software can then be downloaded again to the same monitor, but not to any other
monitor.
1. Make sure that the monitor is switched to standby. Press and hold the service reset button on
the rear panel for at least five seconds or until the service reset indicator LED turns off.
2. Open the cover for card drive slots, if installed. Insert the software card into one of the card drive
slots and press the software card firmly in position.
3. Make sure that at least 30 seconds have passed since the service reset, then switch the monitor
on.
40
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
4.
5.
6.
7.
8.
9.
Wait for approximately 80 seconds. After the start-up screen appears, enter the Service View
and make sure that the information regarding the monitor software has been updated.
Memorize the serial number of the new software.
Remove the software card.
Replace the original device plate for monitor software by the new one supplied with the software
card.
Perform Factory Reset. Make sure that the monitor functions normally after the restart.
Set the time and date.
Set the monitor’s network communication according to the used network software, if necessary.
The communication is set in the monitor’s Network service menu.
Network software S-CNET99 -> DRI Level = 1999
Network software S-CNET01 -> DRI Level = 2001
Network software S-CNET02 -> DRI Level = 2001 or 2002 (WLAN)
Network software L-NET03 -> DRI Level = 2003
Network software L-NET05 -> DRI Level = 2005
NOTE: The DRI Level 1999 is not selectable in all monitor software versions.
NOTE: If the DRI level is changed, the monitor will restart automatically.
Fill out all necessary documentation regarding the new monitor software.
NOTE: The license agreement of monitor software needs to be in accordance with the monitor
software serial number. Make sure you archive the license agreement in a secure location.
NOTE: The first start-up after software loading takes considerably longer.
See also the troubleshooting chart for the software card, if necessary.
3.3.16 Performing Factory Reset
NOTE: The factory reset is necessary after replacing monitor software.
NOTE: The factory reset will restore all customized defaults, including language selection, to factory
defaults.
1.
2.
3.
4.
5.
3.4
Press the Monitor Setup key.
Select Install/Service and password (16-4-34).
Select Service and password (26-23-8).
Select Set/ Test and Factory Reset.
The monitor will perform an automatic restart. After the restart is completed, restart the monitor
also manually.
Adjustments and calibrations
It is not necessary to perform calibrations or adjustments on S/5 Compact Monitors.
41
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4
Troubleshooting
4.1
General (Display Unit)
Trouble
Cause
Treatment
Monitor is not starting
1. On/Stby key pressed too long.
2. The batteries are empty.
3. If power cord connected, AC/DC power unit
may be faulty.
4. If AC/DC power unit is working, the PMB
board in the Frame Unit may be faulty.
5. On/Stby key may be faulty.
1. On/Stby key may be pressed less than 10 s.
2. Connect the power cord.
3. Exchange the AC/DC power unit.
1. The connection between Frame Unit and
Display Unit may be faulty.
2. Display Unit voltages are not OK.
1. Check the connector and the cables
between Display Unit and Frame Unit.
2. Replace the Display Unit DC/DC power
board.
3. Replace the Central Processing Board.
Monitor is not starting, the Frame Unit
back panel led is lit.
3. Faulty Central Processing Board.
4. Exchange the PMB board.
5. Exchange the DU side panel keyboard foil.
The monitor starts (Frame Unit back panel 1. The LCD display cables are loose.
led is lit and a beep is heard), but the
display remains black.
2. The backlights are not lit.
1. Check the LCD cables and connectors on
the Central Processing Board and in the Front
Unit.
2. Connector Board cable may be loose.
Check the cable.
Backlights may be faulty. Exchange them.
Backlight Inverter may be faulty. Exchange the
Inverter.
Module data disappears from the screen. Parameter module current (in PMB) too high.
Detach and change the parameter module.
PMB module power section may be faulty.
Exchange the PMB.
‘Battery failure’ message on the display.
1. Problem in communication between Display 1. Check the connectors and cables between
Unit and Frame Unit (in Service View PMB serial Display Unit and Frame Unit.
number and other data faulty)
2. PMB in Frame Unit may be faulty
2. Exchange the PMB.
Recorder is not working properly.
1. Recorder communication problem.
2. Problem in voltages in Frame Unit.
1. Check the connectors and cables between
Display Unit and Frame Unit.
2. Check the Frame Unit voltages from the
service menu. If not OK, replace the PMB
board.
Keyboard not working, but module
communication is OK.
Keyboard cables and connectors, or Connector
Board cable and connector) may be faulty.
Check the Connector Board cable and
connector.
Check the keyboard cable connection to the
connector board.
Keyboard not working, and module
communication not working.
UPI section of the Central Processing Unit not
functioning normally.
Restart the monitor.
Replace the Central Processing Board.
Keyboard partly not working.
1. Keyboard faulty.
2. Connector Board faulty
1. Replace the keyboard foil.
2. Replace the Connector Board.
'Display temperature high' and
'Check dust filter' messages.
The temperature inside the display unit has
been more than 55 °C for two minutes at the
minimum.
Check and change the dust filter if necessary.
42
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
Trouble
Cause
'Battery temperature high' and
'Check dust filter' messages.
The temperature of the batteries is more than 53 Check and change the dust filter if necessary.
°C.
Display Unit is too warm.
Display Unit Fan is not working.
Check the Fan cable is connected to the
correct connector.
After shut off, the trend and patient data
does not remain 15 min in the memory.
The On/Stby switch has been pressed for over
10 s. (= service reset)
When switching off, the On/Stby switch has to
be pressed for less than 10 s.
4.2
Treatment
Software License (service software)
Trouble
Cause
Treatment
New software is not downloaded or
Start-up display does not appear in 80
seconds.
1. The software card is not properly inserted.
1. Check the software card’s connection in
drive.
2. Check that correct software card is inserted
in drive.
The software serial number in the Service
view is not correct after downloading.
The software has not been downloaded
correctly.
2. The software card does not contain proper
software.
Check the software card’s connection in drive.
Try downloading once again.
Try with an other software card.
Please read the note below*
NOTE: You can download the software only onto one monitor. During the downloading of software the
serial number of the monitor is written on the software card, and if the loading for some reason would
fail, the software can be downloaded again onto the same monitor, but not onto any other monitor.
4.3
Error messages
Message
Explanation
SRAM Error
The SRAM memory is located on the CPU board. The SRAM Error is due to memory malfunction.
Restart the monitor. If the problem persists, replace the SRAM/Timekeeper battery. Remember
to perform factory reset after the replacement.
EPROM Error
The EPROM Error message is displayed due to problems in the communication between the CPU
board and the software flash memory. Replace the CPU board. Remember to perform factory
reset after the replacement.
EEPROM Error
The EEPROM memory is located on the CPU board. The EEPROM Error message is displayed due
to memory malfunction. Perform factory reset. If the problem persists, replace the CPU board.
Remember to perform factory reset after the replacement.
RAM Error
The RAM memory is located on the CPU board. The RAM Error message is displayed due to
memory malfunction. Replace the CPU board. Remember to perform factory reset after the
replacement.
43
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
4.4
Memory Option
Trouble
Cause
Treatment
‘Two Data Cards in mem. module’ message Two Data cards detected.
Remove MemCard from the left hand side slot
of the module.
‘Two Menu Cards in mem. module’ message Two Menu cards detected.
Remove MemCard from the right hand side slot
of the module.
‘No menus in Menu Card’ message
There are no menus in the Menu card.
Insert a Menu card with valid menu
configuration files in the module.
‘Faulty Data Card - change card’ message
An error has occurred during Data card
read/write operation
Change Data card.
‘Faulty Menu Card - change card’ message
An error has occurred during Menu card
read/write operation
Change Menu card.
4.5
Troubleshooting for the NET section
Trouble
Cause
Treatment
Monitor does not connect to the network.
Monitor connects to the network, but
disconnects unexpectedly (‘Network
connection down’ message on the
monitor screen).
Patch panel
Patch cable not connected to HUB or to panel.
Patch cable
Patch cable or connector defective.
HUB not connected to the power supply.
HUB port closed due to physical layer problems.
HUB port temporarily closed and reopened due to physical
layer problems.
Hubs not properly connected to each other.
Monitor-Network cable
Cable not properly connected to the wallplate or to the
monitor.
Monitor-Network cable
Cable or connector defective.
Net section of the CPB
The NET section is defective. Replace the CPB.
NET section memory on the CPB
The SRAM of the NET section is defective or uninitialized. The
NET cannot be used. See network service page for details.
Identification plug
There is no identification plug attached to the monitor.
The identification plug is defective or uninitialized. The plug
cannot be used.
Monitor does not connect to the Network
No Network Option in the monitor
Download the Network option from the appropriate software
card.
‘Check network connectors’ message
shows on the monitor screen
Monitor-Network cable
Cable not properly connected to the wallplate or to the
monitor.
Cable or connector defective.
Identification plug
There is no identification plug properly attached to the
monitor.
The identification plug is defective or uninitialized. The plug
cannot be used. See network service page for details.
44
Document no. M1031520-02
Display Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
‘Network board error’ message shows on
the monitor screen
NET section on the CPB
The NET section is defective. The board cannot be used. See
network service page for details.
NET section memory on the CPB
The SRAM memory of the NET section is defective or
uninitialized. The board cannot be used. See network service
page for details.
Other Site View shows no waveforms
No waveforms are set up for
Run Datex-Ohmeda Network Setup to verify current
Monitor-to-Monitor communication Monitor-to-Monitor communication setup.
Network printing fails
Print server is busy
Network manager's print server is busy at the moment and
cannot take more print jobs. Try again after 15 seconds.
Print queue is full
There are too many unprinted documents waiting in the print
queue. Check the printer, as it is not operating properly.
Printer is off-line
Printer cable is loose, printer is out of paper, there is a paper
jam or the printer is simply switched to off-line state.
There are no menus for the record
keeper
Run Datex-Ohmeda Network Setup to verify the current set up.
Record keeper menus are blank
45
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
5
Earlier revisions
This manual fully supports the earlier revisions of the S/5 Compact Anesthesia and Compact Critical
Care Monitors.
46
Document no. M1031520-02
Appendix A, Service check form, S/5 Compact Anesthesia Monitor, S/5 Compact Critical Care Monitor
APPENDIX A Service check form, S/5 Compact Anesthesia Monitor,
S/5 Compact Critical Care Monitor
Customer
Module type
Service
S/N
Date
Service engineer
Monitor Installation
F-
E-
E-
S-
E-
M-
L-
M-
N-
OK = Test OK
OK
N.A. = Test not applicable
N.A.
Fail = Test failed
Fail
OK
1. DC/DC power supply
board
2. Central Processing Board
3. DC/DC power board
4. Net Unit and
Synchronization Unit
5. Front Unit
6. External parts
7. Inserting module
8. Fan filter
9. Stand-by LED
10. Start-up
11. Monitor screen
configuration
12. Mark Event or Take
Snapshot
13. Time and date
14. Loudspeaker
N.A.
Fail
15. Display brightness
16. Monitor software
L
Power Management board
software
17. Content of service log
A-1
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
18. Power supply output voltages
+12 V
11.50...12.50 V
+3.3 V
3.00....3.60 V
Vbus
10.00...17.00
OK
N.A.
Fail
19. Watchdog circuitry
20. Alarm LEDs
21. Membrane keys check
22. ComWheel check
23. K-ARK connector
24. Module communication
25. Battery
26. Battery voltage
.
10...17 V
27. Monitor temperature
20...40 C
29. Reconnecting the power
cord
28. Battery operation
Notes
Recorder unit
OK
N.A.
Fail
30. Cover open recognition
31. Recording
32. Paper speed
33. Quality of recording
Notes
A-2
Document no. M1031520-02
Appendix A, Service check form, S/5 Compact Anesthesia Monitor, S/5 Compact Critical Care Monitor
S/N
MemCard Option
OK
N.A.
Fail
OK
34. Memory option
recognition
35. Memories and PCMCIA
controller test
36. Interface status
37. Menu Card recognition
38. Card type recognition
39. Data Card recognition
40. Save and Load Modes
41. Data Card functions
N.A.
Fail
N.A.
Fail
Notes
S/N
Network Option
OK
N.A.
Fail
OK
42. Connection to Network
43. Ethernet address
44. Data counters
45. Data error counters
46. Hardware error counters
47. Disconnection
recognition
___________________
48. ID-plug recognition
Notes
S/N
Wireless LAN option
OK
49. Signal strength
N.A.
Fail
OK
50. Configure access point
N.A.
Fail
___________________
51. Connection to the
Network
Notes
A-3
Document no. M1031520-02
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
General
OK
N.A.
Fail
OK
52. Trend retaining
53. Service reset switch
check
54. Battery capacity
55. Service Log reset
56. Electrical safety check
57. Final cleaning
Notes
Used spare parts
Signature
A-4
Document no. M1031520-02
N.A.
Fail
Datex-Ohmeda
S/5TM Compact Anesthesia Monitor,
F-CM1 (Rev. 04), F-CMREC1 (Rev. 01); Frame Unit
AC/DC Power Supply Unit
S/5TM Compact Critical Care Monitor,
F-CMC1 (Rev. 04), F-CMCREC1 (Rev.01); Frame Unit
AC/DC Power Supply Unit
Technical Reference Manual
All specifications are subject to change without notice.
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
Document no. M1044470-01
March, 2006
Datex-Ohmeda Inc.
P.O. Box 7550
Madison, WI 53707-7550, USA
Tel: +1 608 221 1551
Fax: +1 608 222 9147
GE Healthcare Finland Oy
Helsinki, Finland
P.O. Box 900
FI-00031 GE, FINLAND
Tel: +358 10 39411
Fax: +358 9 1463310
www.gehealthcare.com
Copyright  2006 General Electric Company
Table of contents
Table of contents
Table of contents
i
Introduction
1
1
Specifications
2
2
Functional description
3
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
Service procedures
3.1
3.2
3.3
3.4
4
11
General service information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.2.1
Recommended tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.2.2
Recommended parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.2.3
Before beginning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3.2.4
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3.2.5
Functional inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.2.6
Recorder Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
3.2.7
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Disassembly and reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.3.1
To remove the batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.3.2
To remove the AC/DC Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.3.3
To disassemble the Side Frame Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.3.4
To detach/remove the PMB Board (Power Managemet Board) . . . . . . . . . . . . . . . . . . . . . . .19
3.3.5
To detach/remove the Module Mother Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.3.6
To remove the Recorder Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.3.7
Adjustment and Calibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Internal battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.4.1
Battery time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.4.2
Refreshing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.4.3
Replacing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Troubleshooting
4.1
4.2
5
PMB connector board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connector board PMB-REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PMB (Power Management Board) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Module motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
AC/DC Power Supply Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Frame Unit Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
In-built Recorder Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connectors and signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9.1
External Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.9.2
Serial Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
23
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Recorder Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
4.2.1
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Earlier revisions
26
i
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Appendix A: Service check form, S/5 Compact Anesthesia Monitor,
S/5 Compact Critical Care Monitor
ii
Document no. M1044470-01
A-1
Frame Unit for F-CM(C)1 (rev. 04), F-CM(C)REC1 (Rev. 01)
Introduction
This section provides information about the maintenance and service of the following products:
•
S/5 Compact Anesthesia Monitor frame F-CM1 and S/5 Compact Critical Care Monitor frame
F-CMC1 (including the AC/DC power unit, battery and Power Management Board).
•
S/5 Compact Anesthesia Monitor frame F-CMREC1 and S/5 Compact Critical Care Monitor
frame F-CMCREC1 (in addition to the above mentioned parts also a built-in recorder).
All the service menus related to the monitor are described in a separate “Service Menu” slot and the
spare part lists in the “Compact Monitors Spare Parts” slot.
NOTE: Printings on thermal paper may be destroyed when exposed to light, heat, alcohol, etc. Take a
photocopy for archive.
1
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
1
Specifications
Dimensions
Weight
335 x 205 x 340 mm /13.2 x 8.1 x 13.4in
(W x D x H)
8.5 kg (19.4 lbs) (w/o modules)
Electrical Requirements
Power supply
Rated voltage range and frequencies 100 to 240 VAC 50/60 Hz
(limits 90-264 VAC)
Stability
±10 % of nominal voltage
Power consumption
140 VA (max)
Fuses
2x2A, T/SLOW, 250 V
Grounding
Hospital grade
Interruptability
Data memory and alarm settings are saved up to 15 minutes
after monitor standby
Battery
Battery type
Battery charging time
Battery operation
Recharging
Battery operaton alarm
early warning
final warning
Battery state indicator
NiMH, 3.5Ah
10 hours to full capacity
up to 1.5 hours typical on full charge at 23 °C / 73 °F
when connected to mains power
‘Battery low’ note
‘Battery low’ alarm
Capacity bar displayed on the screen
Environmental Requirements
Operating temperature
Storage temperature
Atmospheric pressure
Humidity
10 - 35 °C / 50 - 95 °F
-10 - 50 °C / 14 - 122 °F
500 - 800 mmHg (660 - 1060 mbar, 66 - 106kPa)
10 - 90 % non-condensing
In-built recorder
Power consumption
Principle
Print resolution
Vertical
Horizontal
Paper width
Traces
Print speed
2
Document no. M1044470-01
3W
Thermal array
8 dots/mm (200 dots/inch)
32 dots/mm (800 dots/inch) at a speed of 25 mm/s and
slower
50 mm, printing width 48 mm
Selectable 1, 2, or 3 traces
1, 6.25, 12.5, 25 mm/s
Frame Unit for F-CM(C)1 (rev. 04), F-CM(C)REC1 (Rev. 01)
2
Functional description
The Frame Unit consists of the following parts:
•
•
•
•
•
•
PMB (Power Management Board)
PMB connector board(s)
connector board PMB-REC (in the side frame unit)
two batteries
AC/DC power unit
optionally in-built recorder
The left side of the Frame Unit has places for two double-width modules or four single-width modules.
The network signals are led through their own cables to the Frame Unit. The connectors are placed on
the left side of the Frame Unit in frame version F-CM(C)1 (rev.04). In frame versions F-CM(C)(REC)
(rev.00...03) the connectors are placed on the back plate of the Frame Unit.
The serial data interface is led through the Frame Unit to the AC/DC power unit. The serial connector is
located at the side of the AC/DC power unit.
3
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
CM1 frame
Recorder
Module
motherboard
25-pin D-connector
PMB board
Figure 1
2.1
Battery #1
Battery #2
CM1_frame_block_diag.vsd
Sideplate connector board
25-pin D-connector
Module
connectors
Fan
Frame block diagram
PMB connector board
The PMB connector boards are small boards connected together by a ribbon cable and are both
equipped with the D-25 connectors, one for AC/DC unit and the other for the Display Unit. The board
with the Display Unit connector has also a 16-pin connector for the PMB board.
The PMB connector boards route signals between the AC/DC unit, PMB board and Display Unit.
Signals are transferred via a ribbon cable between the D-connector boards (connected to the AC/DC
and DU). Power lines are transferred separately through the PMB.
2.2
Connector board PMB-REC
The connector board PMB-REC is the one mounted in the Side Frame unit, and connected to the PMB
board via a 15-pin D-connector when inserted into the frame. The connector board PMB-REC routes
operating voltage and signals for the frame cooling fan and for the recorder unit (optional).
4
Document no. M1044470-01
Frame Unit for F-CM(C)1 (rev. 04), F-CM(C)REC1 (Rev. 01)
2.3
PMB (Power Management Board)
Module power supply
Signals to
DU,X4
Module motherboard
conn. X3
PMB +5V supply
CPU unit
Battery
charger
supply
Power path switching
electronics
Fan
power
supply
DU
conn.
X9
AC/DC
conn.
X10
Sideplate connector (D15, X6)
Battery #1
connector
Figure 2
Battery #2
connector
Location of the Power Management Board (side frame panel removed) and the
PMB block diagram
The Power Management Board (PMB) is responsible for distributing DC current for the rest of the
frame. The power source can be the AC/DC unit or one of the internal batteries, and the chosen power
line is referred to as ‘VBUS’. The voltage of VBUS is 10-17V. PMB also controls the fan voltage and
battery charging.
The blocks in “Figure 2” represent different functions on the board.
Module power supply
This block generates the voltages needed for the parameter modules from the selected power source
(VBUS), and delivers those to the module motherboard through connector X3. These voltages are
+5V, +15V, -15V and +15Vdirty.
5
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
PMB CPU unit
The CPU unit controls all other functions of the board. The functions include:
•
•
•
•
•
•
•
•
•
•
Battery current monitoring
Battery capacity calculations
Battery temperature monitoring
Battery charger control
Frame fan voltage control
Level-change of recorder serial line signals
Module power supply measurements (voltages & input current)
Module power supply start-up and shutdown
Power path management (choosing the correct supply source)
Monitor start-up and shutdown control
PMB +5V supply
This unit provides the PMB CPU and other PMB electronics +5V power supply. Input either internal
battery or AC/DC output, output +5V.
Battery charger supply
The charger generates the desired charge current for the batteries from the AC/DC output voltage. At
fast charge rate the current is 1A, at timed charge the current is 500mA for 1/3rd of the time and at
trickle charge rate the current is 500mA for 7/500th of the time. The charge rate is controlled by the
CPU block.
Power path switching electronics
The power source to be used (batteries or AC/DC output) is chosen initially by a ‘power path
controller’ inside this block. The CPU unit has full control over the power path management after the
initial choice is made at start-up. In addition to the power path, the charge current path is also chosen
by the CPU and driven by the power path controller.
WARNING
For as long as the AC/DC unit or either one of the two internal batteries is
connected, the open metal surfaces in this area contain approximately 15V
voltages. An accidential touch of a screwdriver or anything else conductive may
short-circuit the power lines and destroy PMB electronics.
Frame fan power supply
This unit drives the fan (mounted in the side frame unit). It is controlled by the CPU unit, and driven
according to AC/DC current information and frame temperature.
2.4
Module motherboard
The module motherboard routes signals from the PMB to the module slots. Signals include power
supplies and module data buses.
6
Document no. M1044470-01
Frame Unit for F-CM(C)1 (rev. 04), F-CM(C)REC1 (Rev. 01)
2.5
AC/DC Power Supply Unit
The universal AC/DC power supply provides an isolated 15.5 V supply for the S/5 Compact Monitor.
The power unit is attached to the Frame Unit by four screws and a power-D25 connector.
The cooling air for the AC/DC unit is from the Frame Unit fan through cooling holes in the Frame Unit
back plate. The power unit generates a load signal, which is read by the PMB board in the Frame Unit.
The AC/DC power supply is protected by an overvoltage protection. If the output voltage increases
over 17V, the protection is activated and the AC/DC power supply unit does not return to normal
operation until the power cord is briefly disconnected.
2.6
Batteries
There are two NiMH batteries attached to the bottom of the Frame Unit. The PMB board connects one
of the batteries to be the power source, if no power is received from the AC/DC power supply.
The battery charging is controlled by PMB. The normal charge current for the batteries is 170mA RMS.
When the batteries are full, the charging is continued by a 10mA current (trickle charge) to avoid
self-discharge of the batteries.
2.7
Frame Unit Fan
The Frame Unit Fan is used for cooling the Frame Unit electronics, the modules and the AC/DC power
unit. The fan is controlled by the PMB. The rotation speed of the fan is adjusted according to the frame
temperature and AC/DC power unit load. At monitor start-up, the fan is briefly run at full speed to
ensure its operation.
2.8
In-built Recorder Unit
The recorder unit is located in the Side Frame Unit, and it is connected to the Connector Board
PMB-REC with a small connector board and 12-pin flex-strip cable.
External Communication
Reset
+5 V priority
Communication with the monitor Central Processing Board takes place via the Connector Board
PMB-REC, PMB, the Connector Board to Display Unit and the Display Unit DC/DC power unit.
The communication uses +5 V CMOS level RS232 serial interface with an RS485 reset.
The differential RS485 reset from the module bus generates a Recorder Unit reset signal on the
Recorder Board. The Recorder Board also generates a power-up-reset, whose time constant is
approximately 0.1 second. The Recorder Unit reset signal is therefore active when either the Module
Bus RS485-reset or the power-up-reset is active.
The recorder unit supply voltage, +15 VREC is switched on after +5 V is present.
7
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.9
Connectors and signals
Module motherboard
Table 1
Module connector pinout (X1-X4):
25 pin male D-connector
8
Document no. M1044470-01
Pin No.
Signal
1
Reset_485
2
-15V
3
15Vdirty
4
+15V
5
Data_485_
6
Data_485
7
GND
8
Reset_485_
9
CTSB
10
RTSB
11
RXDB
12
TXDB
13
GND
14
NC
15
GND
16
CTSC
17
RTSC
18
RXDC
19
TXDC
20
NC
21
PWM_ECG
22
RXD_RS232
23
TXD_RS232
24
+5V
25
+5V
Frame Unit for F-CM(C)1 (rev. 04), F-CM(C)REC1 (Rev. 01)
2.9.1
External Connectors
Table 2
Network Connector, X5
RJ45 connector
1 2 3 4 5 6 7 8
Table 3
Signal
1
2
3
4
5
6
7
8
Tx +
Tx Rx +
N/C
N/C
Rx N/C
N/C
Coding element connector, X4
9 pin female D-connector
5
1
9
6
Table 4
Pin No.
Pin No.
Signal
1
2
3
4
5
6
7
8
9
IDCS1 (chip select)
IDCL (clock)
IDDI (data in)
IDDO (data out)
IDPE (protect enable)
+5Vdc
Direct ECG
Nurse call
GND
RS232 Serial data connector X11
9 pin male D-connector
Pin No.
Signal
1
2
3
4
5
6
7
8
9
GND
RxD
TxD
NC
GND
N/C
RTS
CTS
N/C
For information about S/5 Compact Monitor external connectors see this manual, Part II Slot I
“Display Unit”.
9
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.9.2
Serial Data Interface
The Serial Data Interface connector is a 9-pin male D-connector (X3) on the side of the AC/DC power
unit.
The serial interface is an asyncronous RS-232 connection which uses hardware flow control. The
communication speed is 115.2 kbps. The communication uses the following parameters: Parity
None, Data bits 8 and Stop bits 1.
For more information about the S/5 Compact Monitor serial data interface see also this manual, Part
II Slot I “Display Unit”.
10
Document no. M1044470-01
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
3
Service procedures
3.1
General service information
The field service of the S/5 Compact Anesthesia Monitor and S/5 Compact Critical Care Monitor is
limited to replacing faulty PC boards and mechanical parts. Return the faulty PC boards to GE
Healthcare for repair.
GE Healthcare is always available for service advice. Please provide the unit serial number, full type
designation and a detailed fault description.
CAUTION
3.2
Only trained personnel with appropriate tools and equipment shall perform the tests
and repairs outlined in this section. Unauthorized service may void the warranty of the
unit.
Service check
S/5 Compact Anesthesia Monitor, F-CM(REC)1
S/5 Compact Critical Care Monitor, F-CMC(REC)1
These instructions include complete procedures for a service check. The service should be performed
after any service repair. Additionally, the service check procedures can also be used for determining
possible failures.
The procedures should be performed in ascending order.
The instructions include a check form (“APPENDIX A”) which should be filled in when performing the
procedures.
The symbol
" in the instructions means that the check list should be signed after performing
the procedure.
3.2.1
Recommended tools
Tool
Order No.
Notes
Power cord
Screwdrivers
Multiparameter hemodynamic module
3.2.2
Recommended parts
Part
Order No.
Frame Unit Fan filter
896085
Recorder paper
74205
Notes
for recorder unit
11
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.2.3
3.2.4
Before beginning
•
•
•
Make sure that the monitor is switched to standby.
•
•
•
Remove the AC/DC Power Unit.
Disconnect the power cord and press the service reset switch until the LED next to it turns off.
If the monitor is connected to the Datex-Ohmeda Network, disconnect the Mon-Net cable. Take
out any memory cards, if installed.
Disassemble the Side Frame Unit.
Detach the battery cables from the Power Management Board.
Visual inspection
1.
Side Frame Unit
Check the Side Frame Unit:
•
•
•
screws are tightened properly
cables are connected properly
connectors are clean and intact
"
2.
PMB and the Connector Boards
Check the Frame Unit from inside. Check the PMB and the Connector Boards:
•
•
•
•
there are no loose objects inside the Frame Unit
all screws are tightened properly
all connectors are clean and intact
cables are connected properly
"
3.
Frame Unit reattached
Reconnect the battery cable.
Reattach the Side Frame Unit.
Reattach the Frame Unit back plate.
Reattach the AC/DC power unit.
"
NOTE: Make sure that all insulation plates are placed correctly before reattaching the rear cover.
4.
Battery slot
Internal parts under bottom cover
Detach the bottom cover and check internal parts:
•
•
12
Document no. M1044470-01
the battery cable is connected properly
the batteries are properly in place
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
•
there are no loose objects inside the battery slot
Reattach the bottom cover.
"
5.
External parts
Check external parts:
•
•
•
•
•
•
•
the four rubber pads under the monitor are all in place
all stickers are intact
the Display Unit is attached properly
all mechanical parts are functioning properly
the service reset switch is intact
the handle is attached properly
the monitor frame is intact
"
6.
Module connections
Check that the module in use goes in smoothly and locks up properly in both module slots.
"
Leave the module connected.
7.
Fan filter
Clean or replace the Frame Unit Fan filter.
"
8.
Recorder
Clean the recorder unit, if installed:
Open the paper compartment cover and take out the paper roll.
Clean the paper compartment off of possible paper chaff.
Clean the thermal printhead and the small glass window before the static brush with a cotton
swab dipped in isopropyl alcohol. Avoid contact with the rubber paper roller.
NOTE: Be careful to limit the application of alcohol to the thermal printhead and the window.
Attach a new paper roll into the recorder and close the cover.
"
9.
Primary fuses
Disconnect the primary fuse holder. Check that:
•
•
the fuse compartment, the fuse holder and the fuses are clean and intact
the fuses are of the correct rating
13
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Reconnect the fuse holder and check that it locks up properly.
"
3.2.5
Functional inspection
10. Stand-by LEDs
Connect the power cord.
Check that the standby LED starts blinking.
Check that the fan starts running.
"
11. Start-up
Switch the monitor on.
Check that the monitor starts up properly, i.e. the alarm LEDs turn blank, the start-up sound is
heard from the loudspeaker and the normal monitoring screen appears.
No error messages should appear on the screen.
"
12. Module recognition
Configure the monitor screen so that all the needed parameter information is shown:
Monitor Setup
Screen 1 Setup
Waveform Fields
Digit Fields
Check that the selected parameter information is shown on the screen.
NOTE: InvBP waveforms are not shown until without a patient simulator. Do no connect the simulator
to the monitor at this stage.
"
13. Main software
Enter the service menu:
Monitor Setup
Install/Service (Password 16-4-34)
Service (Password 26-23-8)
Take down the information regarding Power Management Board software and Battery.
"
14
Document no. M1044470-01
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
14. Content of service log
Select Service Log from the menu. Check the contents of the Service Log for possible problems.
If the monitor contains the recorder unit, record the Service Log on the recorder by selecting
Record Log.
"
15. Voltages
Check the power supply unit output voltages through the service menu:
Monitor Setup
Install/Service (Password 16-4-34)
Service (password 26-23-8)
Frame
Power Supply
The output voltages should meet the following ranges:
+15 V
14.50...15.50 V
-15 V
-14.50...-15.50 V
+15 VD
14.50...15.50 V
+5 V
4.80...5.30 V
VBUS
10.00…17.00 V
+12 V
11.50…12.50 V
+3.3 V
3.00…3.60 V
VBUS
10.00…17.00 V
Preset monitor settings:
Record/Print
Record Waveforms
Waveform 1 --> ecg1
Waveform 2 --> p1
Waveform 3 --> p2
Delay --> Off
Paper Speed --> 6.25 mm/s
Length --> 30 s
16. Module communication
Connect a patient simulator to the module.
Enter the ESTP : ECG service menu:
Monitor Setup
Install/Service (Password 16-4-34)
Service (password 26-23-8)
Parameters
ESTP : ECG
Check that the Timeouts, Bad checksums and Bad c-s by mod values do not increase faster
than by 5 per second.
15
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Change the module into the other slot. When the module is recognized, check that the values do
not still increase faster than by 5 per second.
"
17. Battery voltage
Enter the Battery service menu:
Monitor Setup
Install/Service (password 16-4-34)
Service (password 26-23-8)
Frame
Power Supply
Battery
Check that the shown Battery Voltage value is within 10 – 14V.
"
18. Monitor temperature
Check that the shown Monit Temp value is within 20 - 40.
"
19. Battery operation
Disconnect the power cord (without switching the monitor to standby).
Check that the monitoring continues normally. The battery indicator should appear on the upper
right hand corner of the screen.
"
20. Mains power recognition
Reconnect the power cord.
Check that the LCD display screen brightness increases back to normal and the monitoring
continues without problems. The battery indicator should be replaced by the text CHARGE.
"
3.2.6
Recorder Unit
21. Recorder messages
Open the recorder unit cover.
Check that the message ‘Recorder: Cover open’ appears on the screen, then close the cover.
"
16
Document no. M1044470-01
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
22. Recording
Press the key Record Wave and check that the module starts recording the selected
waveforms. Press the key Stop on the module to stop recording.
NOTE: InvBP waveforms are not recorded without a patient simulator.
NOTE: If no recording appears, check that the paper roll is installed in a correct way. Only one side of
the paper is printable.
"
23. Paper speed
Press the key Record Wave again and this time wait until the recording stops. Check that the
length of the recorded waveform scale is 18.7 cm (1.5 cm).
Change the paper speed setting to 1 mm/s:
Record/Print
Record Waveforms
Paper Speed --> 1 mm/s
Press the key Record Wave and wait until the recording stops. Check that the length of the
scale is now 3.0 cm (± 0.5 cm).
"
24. Quality of recording
Check that the quality of the recordings is acceptable.
"
3.2.7
General
25. Service reset switch
Check the service reset switch.
Switch the monitor to standby and disconnect the power cord. Press the service reset switch for
at least five seconds. Check that the LED next to the switch turns off, and also the fan turns off.
Reconnect the power cord and turn the monitor back on. Check that all trends have now been
erased.
"
26. Battery capacity
Typical lifetime of the Compact Monitor Ni-MH batteries is approximately 4 years.
Test the batteries by performing the following:
•
•
•
•
detach all modules
keep the monitor connected to the mains power until the batteries are fully charged
install a hemodynamic multiparameter module and disconnect the power cord
notice the time the monitor stays on with batteries
17
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Replace the batteries, if the time was less than 45 minutes.
"
27. Battery charging
Reconnect the power cord, switch the monitor on and enter the Battery service menu:
Monitor Setup
Install/Service (Password 16-4-34)
Service (Password 26-23-8)
Frame
Power Supply
Battery
Check that the monitor starts charging one of the batteries and all data is reasonable.
"
28. Service Log reset
Enter the Service Log in the service menu:
Monitor Setup
Install/Service (Password 16-4-34)
Service (Password 26-23-8)
Service Log
Clear the content of the Service Log by selecting Reset Log in the menu.
"
29. Electrical safety check
Perform an electrical safety check and a leakage current test.
Check that the monitor functions normally after the performed electrical safety check.
"
30. Final cleaning
Switch the monitor to standby, disconnect the power cord and perform final cleaning.
After cleaning, reconnect the power cord for recharging the batteries.
"
•
Fill in all necessary documents.
18
Document no. M1044470-01
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
3.3
Disassembly and reassembly
WARNING
The S/5 Compact Monitor is always energized by an internal battery. A short
circuit may cause internal damage. Do not touch any exposed wiring or
conductive surface inside, as this may cause an electric shock.
See the exploded view of the S/5 Compact Monitor Frame Unit in the ‘Spare Parts’ slot to get quick
unerstaning of the structure.
3.3.1
To remove the batteries
1.
2.
Open the Bottom Plate of the Frame Unit by opening the eight screws.
Detach the battery cables and remove the batteries.
NOTE: Remember the order of the batteries connected to the PMB board.
3.3.2
To remove the AC/DC Unit
1.
2.
Open the four screws holding the unit at the back of the Compact Monitor .
Pull the AC/DC Unit carefully to avoid damaging the connector.
NOTE: It is not allowed to repair the AC/DC power unit in the field.
Return the faulty AC/DC power unit to GE Healthcare for service.
3.3.3
To disassemble the Side Frame Unit
1.
2.
3.
4.
5.
Detach/remove the AC/DC Unit.
Open the three screws from the left side of the Frame Unit back plate.
Loosen the long screw at the upper left corner of the Frame Unit.
Open the two screws at the bottom left side of the Frame Unit.
Pull the Side Panel Unit carefully from the connector to the PMB Board and out of the frame.
NOTE: When reassembling the Side Panel Unit, be careful not to damage the components on the PMB
Board.
3.3.4
To detach/remove the PMB Board (Power Managemet Board)
NOTE: It is important to remove the batteries before starting to remove the PMB Board!
NOTE: Remember the order of batteries connected to the PMB Board.
1.
2.
3.
4.
5.
6.
7.
Disassemble the Side Panel Unit.
Open the Bottom Plate of the Frame Unit by opening the eight screws and remove the batteries.
Open the two screws holding the connector to the AC/DC Unit.
Open the two screws holding the connector to the Display Unit.
Detach the Power and Data cables from the PMB Board.
Open the eight screws holding the PMB Board.
Pull the PMB Board carefully to detach it from the Module Mother Board.
19
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.3.5
To detach/remove the Module Mother Board
1.
2.
Detach/remove the PMB Board.
Unscrew the spacers to remove the Module Mother Board.
NOTE: Be carefull not to damage the service reset switch.
3.3.6
To remove the Recorder Unit
Disassemble the Side Frame Unit.
Loosen the screws and extract the recorder.
3.3.7
Adjustment and Calibrations
It is not necessary to perform calibrations or adjustments on the Compact Monitor Frame Unit.
20
Document no. M1044470-01
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
3.4
Internal battery
WARNING
The S/5 Compact Monitor is always energized by an internal battery. A short
circuit may cause internal damage. Do not touch any exposed wiring or
conductive surface inside, as this may cause an electric shock.
The monitor can be run either on mains power or on internal battery. Battery operation is initiated
when the power cord is disconnected or when the mains power is lost during monitoring.
The internal battery capacity is up to 2.5 hours with fully charged batteries.
NOTE: Before using the monitor for the first time, charge the battery to its full capacity (charging time
10 hours).
3.4.1
Battery time
A symbol on the monitor screen indicates the remaining operating time of the battery.
When about 10 minutes of battery operating time is left, a 'Batt low' alarm is activated and the
monitor makes one beep.
When about two minutes of operating time is left, a new alarm 'Batt empty' is activated.
3.4.2
Refreshing the batteries
The battery is automatically charged when the monitor is connected to mains power. Charging the
battery depends on the discharge level of the battery. Battery charging time is ten hours to full
capacity.
If the monitor is used mainly with the mains power, refresh the battery by charging and discharging
the battery completely once a month to slow down loss of battery capacity.
NOTE: If the monitor is used for frequent short transportation, refresh the batteries every two weeks
and replace the batteries every six months.
To refresh:
1. Connect the monitor power cord to power outlet for at least ten hours.
2. Remove the power cord, and turn on the monitor and let it turn off by itself (it takes about 1.5
hours). Wait for 15 minutes.
3. Reconnect the power cord to power outlet and charge the battery for at least ten hours.
NOTE: Inadequate maintenance will decrease the battery capacity and the monitor's operation time
on batteries.
When charging, a charging symbol is displayed.
During battery charging, the standby led is blinking. It lights up when the batteries are fully charged.
21
Document no. M0144470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3.4.3
Replacing the batteries
1.
2.
3.
Open the Bottom Plate of the Frame Unit by opening the eight screws.
Detach the battery cables and remove the batteries.
Insert new batteries and connect the battery cables.
NOTE: Remember the order of the batteries connected to the PMB board.
22
Document no. M0144470-01
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
4
Troubleshooting
For troubleshooting, see also section "Display Unit: Troubleshooting" in this manual.
4.1
General
Trouble
Cause
What to do
Monitor is not starting
1. On/Stby key pressed too long.
1. On/Stby key may be pressed for
less than 10 s.
2. Connect the power cord.
3. Replace the AC/DC power unit.
2. The batteries are empty.
3. If power cord connected. If the
On/Stby LED is lit or blinks. AC/DC
power unit may be faulty.
4. If the Frame unit fan is running. If
AC/DC power unit is working, the PMB
in the Frame Unit may be faulty.
5. On/Stby key may be faulty.
Monitor is not starting, the Frame
Unit back panel LED is lit.
4. Replace the PMB.
5. Replace the Display Unit side panel
keyboard foil.
1. The connection between Frame Unit 1. Check the connector and the cables
and Display Unit may be faulty.
between Display Unit and Frame Unit.
2. Display Unit voltages are not OK.
2. Replace the Display Unit DC/DC
power board.
3. Faulty Central Processing Board.
3. Replace the Central Processing
Board.
The monitor starts (Frame Unit
1. The LCD display cables are
back panel LED is lit and a beep is loose.
heard), but the display remains
black.
2. The backlights are not lit.
1. Check the LCD cables and
connectors on the Central Processing
Board and in the Front Unit.
2.Connector Board cable may be loose.
Check the cable.
Backlights may be faulty. Replace
them.
Backlight inverter may be faulty.
Replace the inverter.
Module data disappears from the Parameter module current (in PMB) too Detach and change the parameter
screen.
high.
module.
PMB module power section may be
faulty. Replace the PMB.
Keyboard not working, but module Keyboard cables and connectors, or
communication is OK.
Connector Board cable and connector
may be faulty.
Check the Connector Board cable and
connector.
Check the keyboard cable connection
to the connector board.
23
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Trouble
Cause
What to do
Keyboard not working, and
module communication not
working.
UPI section of the Central Processing
Unit not functioning normally.
Restart the monitor.
Replace the Central Processing Board.
Keyboard partly not working.
Keyboard faulty.
Replace the keyboard foil.
Connector Board faulty
Replace the Connector Board.
'Display temperature high' and
'Check dust filter' messages.
The temperature inside the display unit Check and change the dust filter if
has been more than 55 °C for two
necessary.
minutes at the minimum.
‘Battery failure’ message on the
display.
1. Problem in communication between 1. Check the connectors and cables
Display Unit and Frame Unit (the PMB between Display Unit and Frame Unit.
serial number and other data faulty in
Service View).
2. PMB in Frame Unit may be faulty.
2. Replace the PMB.
'Frame temperature high' and
'Check dust filter' messages.
The temperature inside the frame is
more than 55 °C.
Check and change the dust filters if
necessary.
'Battery temperature high' and
'Check dust filter' messages.
The temperature of the batteries is
more than 53 °C.
Check and change the dust filters if
necessary.
Display Unit is too warm.
1. Display Unit Fan is not working.
1. Check the Fan cable is connected to
the correct connector.
Recorder is not working properly.
1. Recorder communication problem.
1. Check the connectors and cables
between Display Unit and Frame Unit.
2. Check the Frame Unit voltages from
the service menu. If not OK, replace the
PMB.
2. Problem in voltages in Frame Unit.
After shut down, the trend and
patient data does not remain 15
min in the memory.
1. The On/Stby switch has been
pressed for over 10 s. (= service reset)
2. Faulty PMB.
24
Document no. M1044470-01
1. When switching off, the On/Stby
switch has to be pressed for less than
10 s.
2. Replace the PMB.
Frame Unit for F-CM(C)1 (Rev. 04), F-CM(C)REC1 (Rev. 01)
4.2
Recorder Unit
4.2.1
Troubleshooting chart
Problem
Cause
What to do
Recorder will not start.
No error messages shown.
Connector board loose.
Check connector board connections.
Recorder board faulty.
Replace the recorder board.
Recorder unit faulty.
Replace the recorder unit.
Recorder works but nothing appears Active side of the paper downwards. Turn the paper roll over.
on the paper.
To test which side is active: Place the
paper on a hard surface and draw a line
with a fingernail - a dark line will appear
on the active (thermal) side.
Recorder unit faulty.
Replace the recorder unit.
Message
Explanation
Recorder: out of paper
Release paper jam or insert a roll of paper into the
recorder.
Recorder: cover open
Close the recorder cover correctly.
Recorder: thermal array overheat
Recorder overheated. Stop using and allow it to cool
down.
Recorder: input voltage low
+15 Vrec is too low. Check the connectors and connector
board.
Recorder: input voltage high
+15 Vrec is too high. Check the connectors and connector
board.
Recorder system error
1, 2, 3
System error.
If the problem persists, replace the recorder unit.
Recorder: module removed
A communication error due to a fault in the recorder or in
the Central Processing Board.
25
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
5
Earlier revisions
This manual covers the earlier revisions of the S/5 Compact Anesthesia Monitor or S/5 Compact
Critical Care Monitor.
26
Document no. M1044470-01
Appendix A, Service check form, S/5 Compact Anesthesia Monitor, S/5 Compact Critical Care Monitor
APPENDIX A Service check form, S/5 Compact Anesthesia Monitor,
S/5 Compact Critical Care Monitor
Customer
Module type
Service
S/N
Date
Service engineer
Monitor Installation
F-
E-
E-
S-
E-
M-
L-
M-
N-
OK = Test OK
OK
N.A. = Test not applicable
N.A.
Fail = Test failed
Fail
OK
1. Side Frame Unit
2. PMB and the Connector
Boards
3. Frame Unit reattached
4. Battery slot
5. External parts
6. Module connections
7. Fan filter
8. Recorder
9. Primary fuses
10. Stand-by LEDs
11. Start-up
12. Module recognition
13. Main software
L-
N.A.
Fail
Power Management board
software
14. Content of service log
Notes
A-1
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
15. Voltages
+15 V
14.50...15.50 V
-15V
-14.50...-15.50 V
+15VD
14.50...15.50 V
+5V
4.80...5.30 V
VBUS
10.00…17.00V
+12V
11.50…12.50V
+3.3 V
3.00…3.60V
VBUS
10.00…17.00V
OK
N.A.
Fail
16. Module communication
17. Battery voltage
10...17 V
18. Monitor temperature
20...40 C
19. Battery operation
20. Mains power recognition
Notes
Recorder unit
OK
N.A.
Fail
OK
21. Recorder messages
22. Recording
23. Paper speed
24. Quality of recording
Notes
A-2
Document no. M1044470-01
N.A.
Fail
Appendix A, Service check form, S/5 Compact Anesthesia Monitor, S/5 Compact Critical Care Monitor
General
OK
N.A.
Fail
OK
25. Service reset switch
26. Battery capacity
27. Battery charging
28. Service Log reset
29. Electrical safety check
30. Final cleaning
N.A.
Fail
Notes
Used spare parts
Signature
A-3
Document no. M1044470-01
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
For your notes:
A-4
Document no. M1044470-01
Datex-Ohmeda
S/5TM Compact Anesthesia Monitor
S/5TM Compact Critical Care Monitor
Spare Parts
All specifications are subject to change without notice.
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
M1031521
March, 2006
Datex-Ohmeda Inc.
P.O. Box 7550
Madison, WI 53707-7550, USA
Tel: +1 608 221 1551
Fax: +1 608 222 9147
GE Healthcare Finland Oy
P.O. Box 900
FI-00031 GE, FINLAND
Tel: +358 10 39411
Fax: +358 9 1463310
www.gehealthcare.com
Copyright  2006 General Electric Company
Table of contents
Table of contents
Table of contents
i
1
1
S/5 Compact Monitor Display Unit
1.1
2
F-CM(C)REC1 rev. 00, 01, F-CM(C)1 rev.00...04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1.1
Display unit, bottom unit, F-CM(C)REC1 rev. 00, 01, F-CM(C)1 rev.00...03 . . . . . . . . . . . . . 3
1.1.2
Display unit, bottom unit, F-CM(C)1 rev.04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1.3
Front unit, F-CM(C)(REC)1 rev. 00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1.4
Front unit, F-CM(C)REC1 rev. 01, F-CM(C) rev.01, rev.02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1.5
Front unit, F-CM(C) rev.03...04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
1.1.6
Central Processing Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
S/5 Compact Monitor Frame
2.1
2.2
2.3
2.4
13
F-CM(REC)1, F-CMC(REC)1 rev. 00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
S/5 Compact Monitor Frame, F-CM(C)1 rev. 01, rev. 02, rev. 03, F-CM(C)REC1 rev.01 . . . . . . . . . .15
Side frame unit, F-CM1, F-CMC1 rev.02, rev.03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
S/5 Compact Monitor Frame, F-CM(C)1 rev. 04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3
Software licenses
20
4
Upgrade Kits
20
i
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
ii
Document no. M1031521
Spare Parts
1
S/5 Compact Monitor Display Unit
1.1
F-CM(C)REC1 rev. 00, 01, F-CM(C)1 rev.00...04
Figure 1
Exploded view of the Display Unit and labels
Item
Description
Order No.
4
Cross cyl. head screw M3x6 tufflock
617210
9
Side Panel sticker, DA; F-CM1; S/5
898080
9
Side Panel sticker, DE; F-CM1; S/5
898071
9
Side Panel sticker, EN; F-CM1; S/5
895764
9
Side Panel sticker, ES; F-CM1; S/5
898074
9
Side Panel sticker, FI; F-CM1; S/5
898077
9
Side Panel sticker, FR; F-CM1; S/5
898072
9
Side Panel sticker, HU; F-CM1; S/5
M1042448
9
Side Panel sticker, IT; F-CM1; S/5
898075
9
Side Panel sticker, JA; F-CM1; S/5
898081
9
Side Panel sticker, NL; F-CM1; S/5
898073
Replaced by
1
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
9
Side Panel sticker, NO; F-CM1; S/5
898079
9
Side Panel sticker, PL; F-CM1; S/5
8003506
9
Side Panel sticker, PT; F-CM1; S/5
898076
9
Side Panel sticker, SV; F-CM1; S/5
898078
10
Front Panel sticker, DA; F-CMC1; S/5
898304
10
Front Panel sticker, DE; F-CMC1; S/5
898295
10
Front Panel sticker, EN; F-CMC1; S/5
898294
10
Front Panel sticker, ES; F-CMC1; S/5
898298
10
Front Panel sticker, FI; F-CMC1; S/5
898301
10
Front Panel sticker, FR; F-CMC1; S/5
898296
10
Front Panel sticker, HU; F-CMC1; S/5
M1042413
10
Front Panel sticker, IT; F-CMC1; S/5
898299
10
Front Panel sticker, JA; F-CMC1; S/5
898305
10
Front Panel sticker, NL; F-CMC1; S/5
898297
10
Front Panel sticker, NO; F-CMC1; S/5
898303
10
Front Panel sticker, PL; F-CMC1; S/5
8003509
10
Front Panel sticker, PT; F-CMC1; S/5
898300
10
Front Panel sticker, SV; F-CMC1; S/5
898302
10
Front Panel sticker, DA; F-CM1; S/5
898068
10
Front Panel sticker, DE; F-CM1; S/5
898059
10
Front Panel sticker, EN; F-CM1; S/5
895763
10
Front Panel sticker, ES; F-CM1; S/5
898062
10
Front Panel sticker, FI; F-CM1; S/5
898065
10
Front Panel sticker, FR; F-CM1; S/5
898060
10
Front Panel sticker, HU; F-CM1; S/5
M1042413
10
Front Panel sticker, IT; F-CM1; S/5
898063
10
Front Panel sticker, JA; F-CM1; S/5
898069
10
Front Panel sticker, NL; F-CM1; S/5
898061
10
Front Panel sticker, NO; F-CM1; S/5
898067
10
Front Panel sticker, PL; F-CM1; S/5
8003509
10
Front Panel sticker, PT; F-CM1; S/5
898064
10
Front Panel sticker, SV; F-CM1; S/5
898066
11
Tooth washer
63615
2
Document no. M1031521
Replaced by
Spare Parts
Item
Description
Order No.
12
Screw-cross rec.cylind.h. stzn,m4x40
61761
31
ComWheel; S/5
898794
33
Locking set, F-CM1, SPARE PART
8001522
34
Filter capsule (DU fan), F-CM1
896089
35
Filter (DU), F-CM1
897010
36
LID for Card slots, F-CM1, SPARE PART
8001523
1.1.1
Replaced by
Display unit, bottom unit, F-CM(C)REC1 rev. 00, 01, F-CM(C)1 rev.00...03
Figure 2
Exploded view of the Display Unit, bottom unit
Item
Description
Order No.
14
Screw-cross rec. c/s h, stzn, m3x6
61620
16
Shakeproof washer m3.2
63611
16
Shakeproof washer m3.2
63611
Replaced by
3
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
27
Washer-spring, M3,STZN(FZB),DIN127
634101
47
Cross cylinder-head screw M3x6
61721
47
Cross cylinder-head screw M3x6
61721
54
Central Processing Board, F-CM1
8000110
54
Central Processing Board, F-CM1
8001596
55
NET cable, F-CM1
896527
56
NET Smart key cable, F-CM1
896528
57
Connector unit, NET, F-CM1
896102
58
Cross recess screw UNC 4-40
61841
59
Connector unit, SYNC, F-CM1
894914
60
DC/DC-board, F-CM1
896705
61
Central Processing Board-DC/DC SIGNAL CABLE, F-CM1
8000023
62
Central Processing Board-DC/DC POWER CABLE, F-CM1
8000004
63
Filter bracket (DU fan), F-CM1
896090
64
Fan unit (DU), F-CM1
896555
65
Cross cylinder head screw M3x18 FZB DIN7985
61739
66
Loudspeaker unit, F-CM1
896109
67
DIS power cable, F-CM1
8000007
68
Connector unit, DIS, F-CM1
894912
4
Document no. M1031521
Replaced by
8001596
M1029304
Spare Parts
1.1.2
Display unit, bottom unit, F-CM(C)1 rev.04
Figure 3
Exploded view of the Display Unit, bottom unit
Item
Description
Order No.
14
Screw-cross rec. c/s h, stzn, m3x6
61620
16
Shakeproof washer m3.2
63611
16
Shakeproof washer m3.2
63611
27
Washer-spring, M3,STZN(FZB),DIN127
634101
47
Cross cylinder-head screw M3x6
61721
47
Cross cylinder-head screw M3x6
61721
54
Central Processing Board, F-CM1
8000110
54
Central Processing Board, F-CM1
8001596
55
NET cable, F-CM1
896527
56
NET Smart key cable, F-CM1
896528
57
Connector unit, NET, F-CM1
M1035234
58
Cross recess screw UNC 4-40
61841
59
Connector unit, SYNC, F-CM1
M1029304*
Replaced by
8001596
5
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
60
DC/DC-board, F-CM1
896705
61
Central Processing Board-DC/DC SIGNAL CABLE, F-CM1
8000023
62
Central Processing Board-DC/DC POWER CABLE, F-CM1
8000004
63
Filter bracket (DU fan), F-CM1
896090
64
Fan unit (DU), F-CM1
896555
65
Cross cylinder head screw M3x18 FZB DIN7985
61739
66
Loudspeaker unit, F-CM1
896109
67
DIS power cable, F-CM1
8000007
68
Connector unit, DIS, F-CM1
M1035235
* Not compatible with MRI use
6
Document no. M1031521
Replaced by
Spare Parts
1.1.3
Front unit, F-CM(C)(REC)1 rev. 00
Figure 4
Exploded view of the Display Unit, Front Unit, F-CM(C)(REC)1 rev.00
Item
Description
Order No.
16
Shakeproof washer m3.2
63611
27
Washer-spring, M3,STZN(FZB),DIN127
634101
27
Washer-spring, M3,STZN(FZB),DIN127
634101
40
Membrane keyboard, VERT., F-CM1
895686
41
Front cover for display unit, F-CM(C)(REC)1 Rev. 00
8004619
42
Display-LCD, 12.1in. tft, svga
572793
44
Screw-cross rec.cylind.h. stzn,m3x10
61735
45
EMI-filter, split ferrite core for flat cable 26mm
304514
46
Display cable board (SHARP), F-CM1
895446
47
Cross cylinder-head screw M3x6
61721
48
Connection board (DU), F-CM1
896465
49
Inverter cable (SHARP), F-CM1
896565
50
Display-inverter,12V 2x6mA for572793
572794
Replaced by
7
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
51
Opto-encoder, rotary switch, 16-postions, push button, plastic
shaft, 10inch Ribbon cable and connector
113293
52
Insulator for Invertter, F-CM1
894929
53
Membrane keyboard, HORIS., F-CM1
895685
Complete front unit, F-CM1 rev.00
894908
8
Document no. M1031521
Replaced by
Spare Parts
1.1.4
Front unit, F-CM(C)REC1 rev. 01, F-CM(C) rev.01, rev.02
Figure 5
Exploded view of the Display Front Unit, F-CM(C)(REC)1 Rev.01, F-CM(C) rev 02
Item
Description
Order No.
16
Shakeproof washer m3.2
63611
27
Washer-spring, M3,STZN(FZB),DIN127
634101
37
Cross cylinder head screw M3x8
61722
40
Membrane keyboard, VERT., F-CM1
895686
41
Front cover for display unit, F-CM1 rev.01
8004620
42
Display-LCD,
902673
43
EMC Cover (Display), F-CM1 rev.01
8003870
44
Screw-cross rec.cylind.h. stzn,m3x10
61735
45
EMI-filter, split ferrite core for flat cable 26mm
304514
46
Display cable board, F-CM1 rev.01
8003727
47
Cross cylinder-head screw M3x6
61721
48
Connection board (DU), F-CM1
896465
49
Invertter cable (SHARP), F-CM1 rev 01
8004022
Replaced by
* M1012542
9
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
Replaced by
50
12V inverter for LCD display (902673) M1012542
902674
M1013813
51
Opto-encoder, rotary switch, 16-postions, push button,
plastic shaft, 10inch Ribbon cable and connector
113293
52
Insulator for Invertter, F-CM(C)(REC)1...01
8004024
53
Membrane keyboard, HORIS., F-CM1
895685
Complete front unit, F-CM1 rev.01
8004021
Backlight for display, F-CM1 rev.01
M1001013
* use together with inverter M1013813
10
Document no. M1031521
Spare Parts
1.1.5
Front unit, F-CM(C) rev.03...04
Figure 6
Exploded view of the Display Front Unit, F-CM(C) rev 03...04
Item
Description
Order No.
16
Shakeproof washer m3.2
63611
27
Washer-spring, M3,STZN(FZB),DIN127
634101
37
Cross cylinder head screw M3x8
61722
40
Membrane keyboard, VERT., F-CM1
895686
41
Front cover for display unit, F-CM1 rev.01
8004620
42
Display-LCD,
M1012542
43
EMC Cover (Display), F-CM1 rev.01
M1014033
44
Screw-cross rec.cylind.h. stzn,m3x10
61735
45
EMI-filter, split ferrite core for flat cable 26mm
304514
46
Display cable board, F-CM1 rev.01
8003727
47
Cross cylinder-head screw M3x6
61721
48
Connection board (DU), F-CM1
896465
49
Inverter cable (SHARP), F-CM1 rev 01
8004022
Replaced by
11
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
50
12V inverter for LCD display M1012542
M1013813
51
Opto-encoder, rotary switch, 16-postions, push button, plastic
shaft, 10inch Ribbon cable and connector
113293
52
Insulator for Inverter, F-CM(C)(REC)1...01
8004024
53
Membrane keyboard, HORIS., F-CM1
895685
54
Wire clamp
M1015333
Complete front unit, F-CM1 rev.03
M1014753
Backlight for display, F-CM1 rev.03
M1014385
1.1.6
Replaced by
Central Processing Board
Item
Item description
Order No.
-
Battery for SRAM/Timekeeper
197230
12
Document no. M1031521
Spare Parts
2
S/5 Compact Monitor Frame
2.1
F-CM(REC)1, F-CMC(REC)1 rev. 00
Figure 7
Exploded view of S/5 Compact Monitor Frame
Item
Description
Order No.
1
Frame assembly, F-CM1
896082
2
Handle, F-CM1, SPARE PART
8001521
3
Back plate (FRAME), F-CM1
896083
4
Cross cyl. head screw M3x6 tufflock
617210
4
Cross cyl. head screw M3x6 tufflock
617210
4
Cross cyl. head screw M3x6 tufflock
617210
5
AIM-N-cable,Network connection cable, 0.23m,UTP T568A C5
908680
6
Connector-case, modular coupler, 8-positon, in-line
548737
Replaced by
8004019
13
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
7
Connector shield, F-CM1
8000645
8
NET smart key cable 2, F-CM1
8000701
9
Block screw D-female
546096
10
AC/DC Power supply, PFC,+15.5V,75W
90482
11
Tooth washer
63615
12
Screw-cross rec.cylind.h. stzn,m4x40
61761
13
Fuse T2AH / 250V, 5x20mm
511200
14
Screw-cross rec. c/s h, stzn, m3x6
61620
15
Screw-cross rec.cylind.h. stzn,m3x20
61737
16
Shakeproof washer m3.2
63611
17
Fan unit (side), F-CM1
896564
17
Fan unit (side), F-CM1
896564
18
Filter (side fan), F-CM1
896085
19
Filter bracket (side fan), F-CM1
896086
20
Side frame unit, F-CMREC1 rev. 00 (recorder included)
895500
21
Connector board PMB-REC, F-CM1
896894
22
Screw of D25 connector, F-CM1
897531
22
Screw of D25 connector, F-CM1
897531
23
Power cable, F-CM1
898313
24
PMB-connector board, F-CM1
898108
25
Battery-NiMH,12V,3.5Ah,10x1.2V
17014
26
Bottom plate, F-CM1
8001365
27
Washer-spring, M3,STZN(FZB),DIN127
634101
28
Power management board, F-CM1
896121
29
Spacer, hexagon bar, M3X8,5AV5MSN
640459
30
Module mother board, F-CM1
8000426
32
FRONT PLATE (FRAME), F-CM1
896087
Recorder, Thermal plott.forREC,50,seril.76.8kB
90350
14
Document no. M1031521
Replaced by
Spare Parts
2.2 S/5 Compact Monitor Frame, F-CM(C)1 rev. 01, rev. 02, rev. 03,
F-CM(C)REC1 rev.01
Figure 8
Exploded view of S/5 Compact Monitor Frame
Item
Description
Order No.
1
Frame assembly, F-CM1
896082
2
Handle, F-CM1, SPARE PART
8001521
3
Back plate (FRAME), F-CM1
8004019
4
Cross cyl. head screw M3x6 tufflock
617210
5
AIM-N-cable,Network connection cable, 0.23m,UTP
T568A C5
908680
6
Connector-case, modular coupler, 8-positon, in-line
548737
7
Connector shield, F-CM1 rev. 01
8004290
8
NET smart key cable 2, F-CM1
8000701
9
Block screw D-female
546096
Replaced by
15
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
Item
Description
Order No.
10
AC/DC Power supply, PFC,+15.5V,75W
90482
11
Tooth washer
63615
12
Screw-cross rec.cylind.h. stzn,m4x40
61761
13
Fuse T2AH / 250V, 5x20mm
511200
14
Screw-cross rec. c/s h, stzn, m3x6
61620
15
Screw-cross rec.cylind.h. stzn,m3x20
61737
16
Shakeproof washer m3.2
63611
17
Fan unit (side), F-CM1
896564
18
Filter (side fan), F-CM1
896085
19
Filter bracket (side fan), F-CM1
896086
20
Side frame unit, F-CMREC1, rev. 01 (recorder
included)
895500
Side frame unit, F-CM1, rev. 02...03(recorder not
8005536
20
Replaced by
included)
21
Connector board PMB-REC, F-CM1
896894
22
Screw of D25 connector, F-CM1
897531
23
Power cable, F-CM1
898313
24
PMB-connector board, F-CM1
898108
25
Battery-NiMH,12V,3.5Ah,10x1.2V
17014
26
Bottom plate, F-CM1
8001365
27
Washer-spring, M3,STZN(FZB),DIN127
634101
28
Power management board, F-CM1
8003808
29
Spacer, hexagon bar, M3X8,5AV5MSN
640459
30
Module mother board, F-CM1
8000426
32
FRONT PLATE (FRAME), F-CM1
896087
Recorder, Thermal plott.forREC,50,seril.76.8kB
90350
16
Document no. M1031521
8005308
Spare Parts
2.3
Side frame unit, F-CM1, F-CMC1 rev.02, rev.03
Figure 9
Exploded view of Side frame unit, F-CM(C)1 rev.02, rev.03
Item
Description
Order No.
15
Screw-cross rec.cylind.h. stzn,m3x20
61737
16
Shakeproof washer m3.2
63611
17
Fan unit (side), F-CM1
896564
18
Filter (side fan), F-CM1
896085
19
Filter bracket (side fan), F-CM1
896086
20
Side frame unit, F-CM1 rev.02 (recorder not included)
8005536
Recorder, Thermal plott.forREC,50,seril.76.8kB
90350
21
Connector board PMB-REC, F-CM1
896894
22
Screw of D25 connector, F-CM1
897531
33
Latch
8005503
34
Protection plate 2
8005505
35
Screw
885191
Replaced by
17
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
2.4
S/5 Compact Monitor Frame, F-CM(C)1 rev. 04
Figure 10
Exploded view of S/5 Compact Monitor Frame
Item
Description
Order No.
1
Frame assembly, F-CM1
896082
2
Handle, F-CM1, SPARE PART
8001521
3
Back plate (FRAME), F-CM1
8004019
4
Cross cyl. head screw M3x6 tufflock
617210
10
AC/DC Power supply, PFC,+15.5V,75W
90482
11
Tooth washer
63615
12
Screw-cross rec.cylind.h. stzn,m4x40
61761
13
Fuse T2AH / 250V, 5x20mm
511200
18
Document no. M1031521
Replaced by
Spare Parts
Item
Description
Order No.
14
Screw-cross rec. c/s h, stzn, m3x6
61620
15
Screw-cross rec.cylind.h. stzn,m3x20
61737
16
Shakeproof washer m3.2
63611
17
Fan unit (side), F-CM1
896564
18
Filter (side fan), F-CM1
896085
19
Filter bracket (side fan), F-CM1
896086
20
Side frame unit, F-CMREC1, rev. 04
M1029322
21
Connector board PMB-REC, F-CM1
896894
22
Screw of D25 connector, F-CM1
897531
23
Power cable, F-CM1
898313
24
PMB-connector board, F-CM1
898108
25
Battery-NiMH,12V,3.5Ah,10x1.2V
17014
26
Bottom plate, F-CM1
8001365
27
Washer-spring, M3,STZN(FZB),DIN127
634101
28
Power management board, F-CM1
8003808
29
Spacer, hexagon bar, M3X8,5AV5MSN
640459
30
Module mother board, F-CM1
8000426
32
FRONT PLATE (FRAME), F-CM1
896087
37
BOTTOM INSULATOR, F-CM1
M1034048
Recorder, Thermal plott.forREC,50,seril.76.8kB
90350
Replaced by
8005308
19
Document no. M1031521
Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
3
Software licenses
Description
Order No.
Service Software, anesthesia
S-00A05S/S-00A06S*
Note
Service Software Licence, anesthesia rekord keeping L-00A07S/L-00A08S*
Service Software Licence, anesthesia
L-CANE02(A)S
Service Software License, anesthesia
L-CANE03..02(A)S
Service Software License, anesthesia
L-CANE03..03(A)S
Service Software Licence, anesthesia
L-CANE05(A)S
Service Software Licence, critical care
L-CICU05(A)S
*)The software S-00A06/S-00C04/L-00A08 includes extended bedside arrhythmia analysis.
4
Upgrade Kits
Description
Order No.
Datex-Ohmeda S/5TM Network and MemCard Upgrade
U-CMMEM
Datex-Ohmeda S/5TM Network Upgrade
U-CMNET
Datex-Ohmeda S/5TM Wireless LAN Upgrade
U-CMW
Datex-Ohmeda S/5TM Recorder Upgrade
U-CMREC1
20
Document no. M1031521
Note
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement