QuickScan™ QD2430 - produktinfo.conrad

QuickScan™ QD2430 - produktinfo.conrad
QuickScan™ QD2430
General Purpose Corded
Handheld Area Imager
Bar Code Reader
Quick Reference Guide
Datalogic ADC, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
©2013-2014 Datalogic ADC, Inc.
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described
therein may be reproduced or transmitted in any form or by
any means without prior written permission of Datalogic ADC,
Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic
ADC”). Owners of Datalogic products are hereby granted a
non-exclusive, revocable license to reproduce and transmit
this documentation for the purchaser's own internal business
purposes. Purchaser shall not remove or alter any proprietary
notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any
reproductions of the documentation.
Should future revisions of this manual be published, you can
acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable
from the Datalogic website (www.datalogic.com) or provided
on appropriate media. If you visit our website and would like
to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however,
Datalogic reserves the right to change any specification at any
time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S.A. and
the E.U. All other brand and product names may be trademarks of their respective owners.
Patents
See www.patents.datalogic.com for patent list.
This product is covered by one or more of the following patents:
Design patents: EP002158717, ZL201330271434.1
Utility patents: EP0996284B1, EP0997760B1, EP0999514B1,
EP1128315B1, EP1396811B1, EP1413971B1, EP1828957B1,
JP4435343B2, US6478224, US6512218, US6513714,
US6561427, US6808114, US6997385, US7053954, US7075663,
US7234641, US7387246, US7721966, US8245926, US8561906
Table of Contents
END USER SOFTWARE LICENSE AGREEMENT (EULA) .....................iii
Software Product Policy ............................................................. vi
Customers Under Software Support ................................ vi
Description .................................................................................... 1
Setting Up the Reader ................................................................. 2
Connect/Disconnect Cable to Reader ............................... 2
Using the Quickscan™ QD24XX ................................................... 3
Selecting the Interface Type ....................................................... 4
Interface Selection .............................................................. 4
Configuring the Interface .......................................... 5
Keyboard Interface .................................................... 6
Scancode Tables......................................................... 9
Country Mode ............................................................. 9
Caps Lock State........................................................ 13
Numlock.................................................................... 14
Programming .............................................................................. 15
Using Programming Bar Codes ....................................... 15
Configure Other Settings .................................................. 15
Resetting Product Defaults ............................................. 15
Reading Parameters .................................................................. 16
Aiming System .................................................................. 16
Good Read Green Spot Duration ..................................... 16
Operating Modes ........................................................................ 17
Scan Mode ......................................................................... 17
Pick Mode ........................................................................... 19
Multiple Label Reading ..................................................... 19
Technical Specifications ............................................................ 20
LED and Beeper Indications ...................................................... 23
Error Codes ................................................................................. 26
Cleaning ....................................................................................... 27
Regulatory Information ............................................................. 28
Statement of Agency Compliance ................................... 28
FCC Class B Compliance Statement ................................ 28
Canadian Notice ................................................................ 29
Power Supply ..................................................................... 29
Imager Labeling ................................................................. 30
WEEE Statement ............................................................... 31
Datalogic ADC
Limited Factory Warranty ................................................ 33
Ergonomic Recommendations ................................................. 35
Services and Support ................................................................. 36
Quick Reference Guide
i
NOTES
ii
QuickScan™ QD2430
DATALOGIC ADC, INC.
END USER SOFTWARE LICENSE AGREEMENT (EULA)
FOR THE QUICKSCAN™ QD24XX
Notice to End User: There are two types of software covered by this END USER
LICENSE AGREEMENT ("EULA"): (1) The Datalogic Product you have acquired contains embedded software ("Embedded Software") which is integral to the Product's
operation; and (2) Optional Application Software provided to you on an optional
basis ("Application Software"). Embedded Software and Application Software are
collectively referred to as "Software" and are subject to the terms and conditions
contained in this EULA. Software is provided only for use with, and for authorized
end users of, the Datalogic QuickScan™ QD24XX ("Product"). Portions of the
Embedded Software include or operate with Open Source software or libraries
("Open Source"). Use of Open Source is subject to the Open Source licenses entitled
"QD24XX .zip License File .pdf" available at the following website: http://
www.datalogic.com/software_lan_sb2783_1.html.
This EULA (End User Software License Agreement) ("EULA” or "Agreement") is a
legally binding agreement governing the licensing of the Software and Documentation by Datalogic ADC, Inc. and its subsidiaries and affiliates ("Datalogic") to the
entity or person who has purchased or otherwise acquired a Datalogic Product
("End User"). For purposes of this Agreement, any software that is not Embedded
Software or Application Software is software associated with a separate end-user
license agreement is licensed to you under the terms of that license agreement.
Datalogic and End User hereby agree as follows:
1. Definitions.
1.1 "Affiliate" means a business entity currently existing or later acquired that
controls, is controlled by, or is under common control with Datalogic S.p.A.
1.2 "Documentation" means materials such as user's guides, program reference
guides, quick reference guides, manuals, or similar materials associated with
or related to the Datalogic Product, whether in printed, "online", or other form.
1.3 "Proprietary Information" means: (a) source code, object code, software, documentation, and any related internal design, system design, data base design,
algorithms, technology, technical data or information, implementation techniques, and trade secrets related to the Software, (b) any other trade secrets
marked appropriately or identified as proprietary or confidential, and (c) any
information that End User, under the circumstances, should recognize as confidential. Proprietary Information does not include any information that the
receiving party can establish was (1) in the public domain, (2) already in the
receiving party's possession or rightfully known prior to receipt, (3) rightfully
learned from a third party not in violation of any other's proprietary rights, or
(4) independently developed without access to Proprietary Information.
1.4 "Datalogic Product" means the Datalogic® QuickScan™ series scanner product,
including all embedded Software in and all Documentation related to such
product, which has been purchased or otherwise acquired by End User,
whether obtained directly or indirectly from Datalogic.
1.5 "Software" means any software or computer programs of Datalogic or its third
party licensors in machine readable form which is embedded in the Datalogic
Product, whether obtained directly or indirectly from Datalogic, including any
replacement, update, upgrade, enhancement or modification.
2. Scope Of License Granted.
2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual
license to use the Software, solely on the Datalogic Product in which it is
embedded ("designated Datalogic Product"), in machine-readable form only,
solely for End User's internal business purposes. This Agreement does not
convey ownership of the Software to End User. Title to the Software shall be
and remain with Datalogic or the third party from whom Datalogic has
obtained a licensed right. As used in this Agreement, the term "purchase" or
its equivalents when applied to the Software shall mean "acquire under
license." End User is not entitled to receipt or use of the source code to any
Software.
2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or
otherwise reproduce or remanufacture the Software, whether modified or
unmodified, nor sell, assign, sublicense, distribute, lend, rent, give, or otherwise
transfer the Software to any other person or organization, for purposes other
than as expressly provided in this Agreement, without Datalogic's prior written
consent.
3. Transfers, Support.
3.1 Any copying, installing, reproduction, remanufacture, reverse engineering,
electronic transfer, or other use of the Software on other than the designated
Quick Reference Guide
iii
Datalogic Product will be a material breach of this Agreement. However, Datalogic may elect not to terminate this Agreement or the granted licenses, but
instead may elect to notify End User that End User is deemed to have ordered
and accepted a license for each breaching use. End User shall pay Datalogic
the applicable list price for such licenses as of the date of such breach.
3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Datalogic Product to any third party unless such third party
agrees with Datalogic in writing to be bound by the terms and conditions of
this Agreement. Any such transfer of the Datalogic Product absent such
agreement shall be null and void.
3.3 End User may obtain support for Software from Datalogic at Datalogic's standard support fees and under Datalogic's standard support terms and conditions in effect at the time the support is requested.
4. Intellectual Property.
End User acknowledges that the Software constitutes valuable trade secrets of
Datalogic or Datalogic's third party licensors and that the Software is protected by
intellectual property laws and treaties. The license set forth in this Agreement
does not transfer to End User any ownership of Datalogic's or its third party licensors' copyrights, patents, trademarks, service marks, trade secrets, or other intellectual property rights and End User shall have no right to commence any legal
actions to obtain such rights. End User shall not remove, modify, or take any other
action that would obscure any copyright, trademark, patent marking, or other
intellectual property notices contained in or on the Datalogic Product.
5. Proprietary Information.
5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret property of Datalogic and Datalogic's third party
licensors and End User acquires no right or interest in any Proprietary Information.
5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Information of Datalogic or its third party licensors to any person other
than End User's authorized employees or agents who are under confidentiality
agreement, and End User shall not use the Proprietary Information other than
in conjunction with use of the Datalogic Product exclusively for End User's
internal business purposes. End User shall take steps to protect the Proprietary Information no less securely than if it were End User's own intellectual
property.
5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the termination of this Agreement.
6. Limited Warranty.
6.1 Datalogic warrants that, under normal use and operation, the Datalogic Product will conform substantially to the applicable Documentation for the period
specified in the Documentation. During this period, for all reproducible nonconformities for which Datalogic has been given written notice, Datalogic will
use commercially reasonable efforts to remedy nonconformities verified by
Datalogic. End User agrees to supply Datalogic with all reasonably requested
information and assistance necessary to help Datalogic in remedying such
nonconformities. For all defects reported to Datalogic within the warranty
period, Datalogic's liability is limited to providing End User with one copy of
corrections or responding to End User's problem reports according to Datalogic's standard assistance practices. Datalogic does not warrant that the
product will meet End User's requirements or that use of the product will be
uninterrupted or error free, or that Datalogic's remedial efforts will correct any
nonconformance. This limited warranty does not cover any product that have
been subjected to damage or abuse, whether intentionally, accidentally, or by
neglect, or to unauthorized repair or unauthorized installation, and shall be
void if End User modifies the product, uses the product in any manner other
than as established in the Documentation, or if End User breaches any of the
provisions of this Agreement.
6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS
PROVIDED "AS IS" AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND,
EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT,
AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
7. Infringement.
7.1 Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunder infringe a United States patent or copyright
of a third party and Datalogic will pay any damages finally awarded against
End User by a court of competent jurisdiction that are attributable to such
claim or will pay End User's part of any settlement that is attributable to such
iv
QuickScan™ QD2430
claim, provided, that 1) End User notifies Datalogic promptly in writing of the
claim, 2) Datalogic controls the defense or settlement of the claim, and 3) End
User cooperates fully with Datalogic in such defense or settlement. All notices
of a claim should be sent to Datalogic ADC, Inc., Legal Department, 959 Terry
Street, Eugene, OR 97402.
7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1)
procure for End User the right to continue using the Datalogic Product, 2)
modify the Datalogic Product so that it becomes non-infringing, 3) replace the
Datalogic Product with an equivalent product not subject to such claim, or 4)
provide End User an opportunity to return the Datalogic Product and receive a
refund of the purchase price paid, less a reasonable allowance for use.
7.3 Datalogic shall have no liability to End User for claims of infringement based
upon 1) the use of any Datalogic Product in combination with any product
which Datalogic has not either furnished or authorized for use with such Datalogic Product 2) the use of any Datalogic Product designed, manufactured, or
modified to the specifications of End User, or 3) End User's modification of the
Datalogic Product without written authorization from Datalogic.
7.4 THE FOREGOING STATES DATALOGIC'S COMPLETE AND ENTIRE OBLIGATION
CONCERNING CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL
PROPERTY INFRINGEMENT, CANCELS AND SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING
SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE
PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE
WRITING SIGNED BY BOTH PARTIES.
8. Limitation Of Liability.
EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY
CLAIMS AGAINST END USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED UPON CONTRACT,
TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR
THE DATALOGIC PRODUCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE
LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST DATA,
INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR
OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use.
9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for computer software developed at private expense as
set forth in the U.S. Federal Acquisition Regulations at FAR 52.227-14(g), or
52.227-19 or in the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013(c)(1)(ii), whichever is applicable.
9.2 If End User is using the Datalogic Product outside of the United States, End
User must comply with the applicable local laws of the country in which the
Datalogic Product is used, with U.S. export control laws, and with the English
language version of this Agreement. The provisions of the "United Nations
Convention on International Sale of Goods" shall not apply to this Agreement.
10. Termination.
10.1Either party may terminate this Agreement or any license granted under this
Agreement at any time upon written notice if the other party breaches any
provision of this Agreement.
10.2Upon termination of this Agreement, End User immediately shall cease using
any nonembedded software and shall return to Datalogic or destroy all nonembedded software covered by this Agreement, and shall furnish Datalogic
with a certificate of compliance with this provision signed by an officer or
authorized representative of End User. For embedded software, End User
agrees to sign a waiver prepared by Datalogic concerning further use of the
embedded Software. End User's resumed or continued use of the embedded
Software after termination shall constitute End User's agreement to be bound
by the terms and conditions of this Agreement for such use.
11. General Provisions.
11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to the licensing of the Software and supersedes all prior or contemporaneous agreements, written or oral, between the
parties concerning the licensing of the Software. This Agreement may not be
changed, amended, or modified except by written document signed by Datalogic.
Quick Reference Guide
v
Software Product Policy
11.2 Notice. All notices required or authorized under this Agreement shall be given
in writing, and shall be effective when received, with evidence of receipt.
Notices to Datalogic shall be sent to the attention of Contract Administration,
Datalogic ADC, Inc., 959 Terry Street, Eugene, OR 97402, or such other address
as may be specified by Datalogic in writing.
11.3 Waiver. A party's failure to enforce any of the terms and conditions of this
Agreement shall not prevent the party's later enforcement of such terms and
conditions.
11.4 Governing Law; Venue: This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the
State of Oregon U.S.A, without regard to the rules governing conflicts of law.
The state or federal courts of the State of Oregon located in either Multnomah
or Lane counties shall have exclusive jurisdiction over all matters regarding
this Agreement, except that Datalogic shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory in which End User resides, or in which any of End User's assets are
located.
11.5 Attorneys' Fees. In the event an action is brought to enforce the terms and
conditions of this Agreement, the prevailing party shall be entitled to reasonable attorneys' fees, both at trial and on appeal.
- END -
Software Product Policy
Datalogic reserves the right to ship its products with the
latest version of software/firmware available. This provides our customers with the very latest in Datalogic software technology.
The only exception to this policy is when the buyer has a
signed contract with Datalogic that clearly defines the
terms and conditions for making software/firmware
changes in products shipped to the buyer.
Customers Under Software Support
Customers that elect to subscribe to Datalogic Software
Maintenance and Support Agreement will receive 30 days
advance notification of: (1) the release of a new software
version; and/or (2) discontinuation of any prior software
version that will no longer be supported. Datalogic will
provide maintenance for a fee that will assist customers
in transitioning to the next software version. If a customer
is currently using the software version being discontinued, the customer may elect to transition to any one of
the newer versions, depending on the hardware in use.
To arrange for a Software Maintenance and Support
Agreement please contact your Datalogic sales person.
vi
QuickScan™ QD2430
QuickScan™ QD2430
Description
The QuickScan™ QD2400 2D imager has been specifically created to meet the market demand for omni-directional reading
performance on virtually all codes at an affordable price. Elegant design details are incorporated into a smaller, balanced
lightweight enclosure without sacrificing Datalogic's wellknown durability.
Ideally suited for applications at the point-of-sale (POS), the
QuickScan QD2400 imager features a new illumination and
aiming system developed with the unique intent to reduce
visual stress of the operator during the daily scanning activities. It consists of a soft, dark red illumination combined with
two blue LED triangles pointing at the targeted bar code. The
result is a precise aiming system which contributes to low eye
fatigue, yet still allows top operator efficiency.
Constructed with a combination of design and performancebased ideals such as bar code reading snappiness, motion tolerance, perfect ergonomics and an attractive price, this 2D
imager is the ideal solution for the customer who is looking to
replace their linear only reading scanners with image-based
technology.
OmniDirectional
Operating
To read a symbol simply aim the reader and pull
the trigger. The QuickScan™ QD24XX is a powerful
omni-directional reader, so the orientation of the
symbol is not important.
Datalogic’s exclusive patented ‘Green Spot’ for
good-read feedback helps to improve productivity
in noisy environments or in situations where
silence is required. When using the product with
the cradle at a 45° position, the aiming pattern can
work as an aiming system to aid in positioning the
bar code for quick and intuitive reading.
Quick Reference Guide
1
Setting Up the Reader
Decoding
Reliably decodes all standard 1D (linear) and 2D
bar codes, including GS1 DataBar™ linear codes,
Postal Codes (China Post), Stacked Codes (such as
GS1 DataBar Expanded Stacked, GS1 DataBar
Stacked, GS1 DataBar, Stacked Omnidirectional).
The data stream — acquired from decoding a symbol — is rapidly sent to the host. The reader is
immediately available to read another symbol.
Setting Up the Reader
Follow the steps below to connect and get your reader up and
communicating with its host.
1. Connect the Cable to the reader and the Host.
2.
Configure the Interface (see page 5).
3.
Configure the Reader starting on page 15 (optional,
depends on settings needed).
Connect/Disconnect Cable to Reader
Figure 1. Connecting to the Reader
Side View
Rear
View
Host Connection — The QuickScan plugs directly into the host
device as shown in Figure 2. The power can also be supplied
through an external power supply via the Interface Cable supplied with a power jack.
2
QuickScan™ QD2430
Using the Quickscan™ QD24XX
Figure 2. Connecting to the Host
B
Side
View
US
Using the Quickscan™ QD24XX
The Quickscan™ QD24XX normally functions by capturing and
decoding codes. The aiming system is activated on trigger pull
and indicates the center of the field of view which should be
positioned over the bar code:
Aiming System
Relative Size and Location of Aiming System Pattern
Linear bar
Quick Reference Guide
2D Matrix symbol
3
Selecting the Interface Type
A beam illuminates the label. The projected pattern of the
aiming system will be smaller when the reader is closer to the
bar code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read
closer to the unit. Symbologies with larger bars or elements
(mil size) should be read farther from the unit.
If the aiming system is centered you will get a good read. Successful reading is signaled by an audible tone plus a goodread green spot LED indicator.
Reference the QuickScan QD24XX Product Reference Guide
(PRG) on the Datalogic website for more information about
this feature and other programmable settings.
Selecting the Interface Type
Upon completing the physical connection between the reader
and its host, proceed directly to Interface Selection below for
information and programming for the interface type the
reader is connected to (for example: RS-232, Keyboard Wedge,
USB, etc.) and scan the appropriate bar code to select your
system’s correct interface type.
Interface Selection
The reader model will support one of the following sets of
host interfaces:
General Purpose Models — RS-232, RS-232 OPOS, USB, Keyboard Wedge.
Retail Point of Sale Models — RS-232, RS-232 OPOS, USB.
Information and programming options for each interface type
are provided in this section. For defaults and additional information associated with each interface, proceed to the corresponding chapter in the QuickScan QD2430 PRG.
4
QuickScan™ QD2430
Selecting the Interface Type
Configuring the Interface
Scan the appropriate programming bar code to select the
interface type for your system.
Unlike some other programming features and
options, interface selections require that you
scan only one programming bar code label. DO
NOT scan an ENTER/EXIT bar code prior to scanning an interface selection bar code.
Some interfaces require the scanner to start in
the disabled state when powered up. If additional scanner configuration is desired while in
this state, pull the trigger and hold for 5 seconds. The scanner will change to a state that
allows programming with bar codes.
RS-232
RS-232 standard interface
Select RS232-STD
RS-232 Wincor-Nixdorf
Select RS232-WN
RS-232 for use with OPOS/UPOS/JavaPOS
Select RS-232 OPOS
Quick Reference Guide
5
Selecting the Interface Type
RS-232 (continued)
USB Com to simulate RS-232 standard interface
Select USB-COM-STDa
USB-OEM
USB-OEM (can be used for OPOS/UPOS/JavaPOS)
Select USB-OEM
a. Download the correct USB Com driver from www.datalogic.com
Keyboard Interface
Use the programming bar codes to select options for
USB Keyboard and Wedge Interfaces.
KEYBOARD
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/
Standard Key Encoding
Select KBD-AT
Keyboard Wedge for IBM AT PS2 with standard key encoding
but without external keyboard
Select KBD-AT-NK
6
QuickScan™ QD2430
Selecting the Interface Type
KEYBOARD (continued)
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Alternate Key
Select KBD-AT-ALT
Keyboard Wedge for IBM AT PS2 with alternate key encoding
but without external keyboard
Select KBD-AT-ALT-NK
PC/XT w/Standard Key Encoding
Select KBD-XT
Keyboard Wedge for IBM Terminal 3153
Select KBD-IBM-3153
Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx
make break keyboard
Select KBD-IBM-MB
Quick Reference Guide
7
Selecting the Interface Type
KEYBOARD (continued)
USB Keyboard with alternate key encoding
Select USB Alternate Keyboard
USB Keyboard for Apple computers
Select USB-KBD-APPLE
Keyboard Wedge for DIGITAL Terminals
VT2xx, VT3xx, VT4xx
Select KBD-DIG-VT
USB Keyboard with standard key encoding
Select USB Keyboard
8
QuickScan™ QD2430
Selecting the Interface Type
Scancode Tables
Reference the QuickScan QD2430 PRG for information about
control character emulation for keyboard interfaces.
Country Mode
This feature specifies the country/language supported by the
keyboard. Only these interfaces support ALL Country Modes:
•
USB Keyboard (without alternate key encoding)
•
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Std Key Encoding
•
Keyboard Wedge for IBM AT PS2 with standard key
encoding but without external keyboard
•
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
without Alternate Key
•
Keyboard Wedge for IBM AT PS2 without alternate
key encoding but without external keyboard
All other interfaces support ONLY the following Country
Modes: U.S., Belgium, Britain, France, Germany, Italy, Spain,
Sweden.
COUNTRY MODE
ENTER/EXIT PROGRAMMING MODE
Country Mode = U.S.
Country Mode = Belgium
Quick Reference Guide
9
Selecting the Interface Type
COUNTRY MODE (continued)
Country Mode = Croatia*
Country Mode = Czech Republic*
Country Mode = Denmark*
Country Mode = France
$CKBCO13(CR)
Country Mode = French Canadian*
Country Mode = Germany
*Supports only the interfaces listed in the Country Mode feature description
10
QuickScan™ QD2430
Selecting the Interface Type
COUNTRY MODE (continued)
Country Mode = Hungary*
Country Mode = Italy
Country Mode = Japanese 106-key*
Country Mode = Lithuanian*
Country Mode = Norway*
Country Mode = Poland*
*Supports only the interfaces listed in the Country Mode feature description
Quick Reference Guide
11
Selecting the Interface Type
COUNTRY MODE (continued)
Country Mode = Portugal*
Country Mode = Romania*
Country Mode = Spain
Country Mode = Sweden
Country Mode = Slovakia*
Country Mode = Switzerland*
*Supports only the interfaces listed in the Country Mode feature description
12
QuickScan™ QD2430
Selecting the Interface Type
Caps Lock State
This option specifies the format in which the reader sends
character data. This applies to keyboard wedge interfaces.
This does not apply when an alternate key encoding keyboard
is selected.
CAPS LOCK STATE
ENTER/EXIT PROGRAMMING MODE
Caps Lock State = Caps Lock OFF
Caps Lock State = Caps Lock ON
Caps Lock State = AUTO Caps Lock Enable
Quick Reference Guide
13
Selecting the Interface Type
Numlock
This option specifies the setting of the Numbers Lock (Numlock) key while in keyboard wedge interface. This only applies
to alternate key encoding interfaces. It does not apply to USB
keyboard.
NUMLOCK
ENTER/EXIT PROGRAMMING MODE
Numlock = Numlock key unchanged
Numlock = Numlock key toggled
14
QuickScan™ QD2430
Programming
Programming
The reader is factory-configured with a set of standard
default features. After scanning the interface bar code from
the Interfaces section, select other options and customize
your reader through use of the programming bar codes available in the QuickScan QD24XX PRG. Check the corresponding
features section for your interface, and also the Data Editing
and Symbologies chapters of the PRG.
Using Programming Bar Codes
This manual contains bar codes which allow you to reconfigure your reader. Some programming bar code labels, like the
"Reset Default Settings" on page 15, require only the scan of
that single label to enact the change.
Other bar codes require the reader to be placed in Programming Mode prior to scanning them. Scan an ENTER/EXIT bar
code once to enter Programming Mode; scan the desired
parameter settings; scan the ENTER/EXIT bar code again to
accept your changes, which exits Programming Mode and
returns the reader to normal operation.
Configure Other Settings
Additional programming bar codes are available in the PRG to
allow for customizing programming features. If your installation requires different programming than the standard factory default settings, refer to the PRG.
Resetting Product Defaults
If you aren’t sure what programming options are in your
reader, or you’ve changed some options and want your custom factory settings restored, scan the bar code below to
reset the reader to its initial configuration. Reference the PRG
for other options, and a listing of standard factory settings.
Factory defaults are based on the interface
type. Be sure your reader is configured for the
correct interface before scanning this label.
See "Selecting the Interface Type" on page 4
for more information.
Reset Default Settings
Quick Reference Guide
15
Reading Parameters
Reading Parameters
Move the reader toward the target and center the aiming pattern and illumination system to capture and decode the
image. See Using the Quickscan™ QD24XX on page 3 for more
information.
The aiming system will briefly switch off after the acquisition
time, and if no code is decoded will switch on again before the
next acquisition. The illuminator will remain on until the symbol is decoded.
As you read code symbols, adjust the distance at which you
are holding the reader.
Aiming System
A number of options for customizing control of the Aiming
System are available. See the QuickScan QD24XX PRG for
more information and programming bar codes.
Good Read Green Spot Duration
Successful reading can be signaled by a good read green spot.
Use the bar codes that follow to specify the duration of the
good read pointer beam after a good read.
GOOD READ GREEN SPOT DURATION
ENTER/EXIT PROGRAMMING MODE
Disabled
Medium (500 ms)
16
♦ Short (300 ms)
Long (800 ms)
QuickScan™ QD2430
Operating Modes
Operating Modes
Scan Mode
The imager can be set to operate in one of several scanning
modes. See the PRG for more information and settings for
any of the options:
Trigger Single (Default) — This mode is associated with typical
handheld reader operation. When the trigger is pulled, illumination is turned on and the scanner attempts to read a label.
Scanning is activated until one of the following occurs:
•
the programmable “maximum scan on time”1 has
elapsed
•
a label has been read
•
the trigger is released
Trigger Pulse Multiple — Scanning begins when the trigger is
pulled and continues after the trigger is released, until the
trigger is pulled again or until the programmable “maximum
scan on time”1 has elapsed. Reading a label does not disable
scanning. Double Read Timeout1 prevents undesired multiple
reads while in this mode.
Trigger Hold Multiple — When the trigger is pulled, scanning
starts and the product scans until the trigger is released or
“maximum scan on time”1 has elapsed. Reading a label does
not disable scanning. Double Read Timeout1 prevents undesired multiple reads while in this mode.
Always On — The illuminator is always ON and the reader is
always ready for code reading. Double Read Timeout1 prevents undesired multiple reads.
Flashing — The reader illuminator flashes on and off regardless of the trigger status. Code reading takes place only
during the Flash On2 time. Double Read Timeout1 prevents
undesired multiple reads.
Object Detection — The scanner looks for changes within its
field-of-view. The Aiming Pattern is always on to show the
optimum reading area. If a predefined amount of movement
is detected, the red illumination switches on. Scanning continues until a label is read or "maximum scan on time" is
reached.
1. See the Product Reference Guide (PRG) for these and
other programmable features
2. Controlled by Flash On Time and Flash Off Time. Use
the PRG to program these options.
Quick Reference Guide
17
Operating Modes
SCAN MODE
♦ Scan Mode = Trigger Single
Scan Mode = Trigger
Hold Multiple
Scan Mode = Always On
18
Scan Mode = Trigger
Pulse Multiple
Scan Mode = Flashing
Scan Mode =
Object Detection
QuickScan™ QD2430
Operating Modes
Pick Mode
Specifies the ability of the reader to decode labels only when
they are close to the center of the aiming pattern, which is the
area indicated by the two blue arrows. Pick Mode is a Decoding and Transmission process where bar codes that are not
within the configurable distance from the center of the aiming
pattern are not acknowledged or transmitted to the host. It is
active only while the scanner is in Trigger Single mode. If the
scanner switches to a different Read Mode, Pick Mode is
automatically disabled.
This feature is not compatible with Multiple
Labels Reading in a Volume. See the PRG for
more information.
PICK MODE
ENTER/EXIT PROGRAMMING MODE
♦ PIck Mode = Disable
Pick Mode = Enable
Multiple Label Reading
The reader offers a number of options for multiple label reading. See the PRG or software configuration tool for descriptions of these features and programming labels.
Quick Reference Guide
19
Technical Specifications
Technical Specifications
The following table contains Physical and Performance Characteristics, User Environment and Regulatory information.
Item
Description
Physical Characteristics
Color
Black & white
Dimensions
Height 6.4"/163 mm
Length 3.6"/91 mm
Width 1.6"/41 mm
Weight (without cable)
Approximately 5.1 ounces/145 g
Electrical Characteristics
Voltage & Current
Input Voltage: 4.5 - 14.0VDC
Operating (typical): 140mA
Operating (max): 380mA
Idle/standby (typical): 50mA
Performance Characteristics
Light Source
LEDs
Roll (Tilt) Tolerance
Up to ± 360°
Pitch Tolerance
± 65°
Skew (Yaw) Tolerance
± 60°
Print Contrast Minimum
25% minimum reflectance
20
QuickScan™ QD2430
Technical Specifications
Depth of Field (Typical)a
Symbology
a.
Code 39
5mil: 0.2" - 5.9" (0.5 - 15cm)
10mil: 0" - 8.7" (0 - 22cm)
20mil: up to 16" (40cm)
EAN
7.5mil: 0" - 5.9" (0 - 15cm)
13mil: 0.2" - 13.8" (0.5 - 35cm)
PDF-417
6.6mil: 0.39" - 5.1" (1.0 - 130cm)
10mil: 0" - 8.3" (0 - 21cm)
15mil: 0.2" - 9.5" (0.5 - 24cm)
DataMatrix
10mil: 0.39" - 5.1" (1.0 - 13 cm)
15mil: 0" - 7.1" (0 - 18cm)
QR Code
10mil: 0.2" - 5.1" (0.5 - 13cm)
15mil: 0" - 7.1" (0 - 18cm)
Minimum
Element Width
Standard Range:
1D Min Resolution = 4 mil
PDF-417 Min Resolution = 5 mil
Datamatrix Min Resolution = 7.5 mil
13 mils DOF based on EAN. All other 1D codes are Code 39. All labels grade A, typical environmental light,
20°C, label inclination 10°
Quick Reference Guide
21
Technical Specifications
Decode Capability
1D Bar Codes
UPC/EAN/JAN (A, E, 13, 8); UPC/EAN/JAN (including P2 /P5); UPC/EAN/JAN (including; ISBN /
Bookland & ISSN); UPC/EAN Coupons; Code 39 (including full ASCII); Code 39 Trioptic; Code39
CIP (French Pharmaceutical); LOGMARS (Code 39 w/ standard check digit enabled); Danish
PPT; Code 32 (Italian Pharmacode 39); Code 128; Code 128 ISBT; Interleaved 2 of 5 ; Standard
2 of 5; Interleaved 2 of 5 CIP (HR); Industrial 2 of 5; Discrete 2 of 5; Matrix 2 of 5; IATA 2of5 Air
cargo code; Code 11; Codabar; Codabar (NW7); ABC Codabar; EAN 128; Code 93 ; MSI; PZN;
Plessey; Anker Plessey; GS1 DataBar Omnidirectional; GS1 DataBar Limited; GS1 DataBar
Expanded; GS1 DataBar Truncated; DATABAR Expanded Coupon.
2D / Stacked Codes
The QuickScan QD24XX scanner is capable of decoding the following sybmologies using multiple frames (i.e. Multi-Frame Decoding):
Datamatrix; Inverse Datamatrix; Datamatrix is configurable for the following parameters:;
Normal or Inverted; Square or Rectangular Style; Data length (1 - 3600 characters); Maxicode; QR Codes (QR, Micro QR and Multiple QR Codes); Aztec; Postal Codes - (Australian Post;
Japanese Post; KIX Post; Planet Code; Postnet; Royal Mail Code (RM45CC); Intelligent Mail
Barcode (IMB); Sweden Post; Portugal Post); LaPoste A/R 39; PDF-417; MacroPDF; Micro
PDF417; GS1 Composites (1 - 12); French CIP13a; GS1 DataBar Stacked; GS1 DataBar Stacked
Omnidirectional; GS1 DataBar Expanded Stacked; GSI Databar Composites; Chinese Sensible
Code; Inverted 2D codesb .
a
It is acceptable to handle this with ULE
b
The SW can apply the Normal/Reverse Decoding Control to the following symbologies: Datamatrix, QR,
Micro QR, Aztec and Chinese Sensible Code.
Interfaces Supported
RS-232, Keyboard Wedge, USB Com Std., USB Keyboard,
USB OEM
User Environment
Operating Temperature
0° to 50° C (32° to 122° F)
Storage Temperature
-40° to 70 °C (-40° to 158° F)
Humidity
Operating: 0% to 95% relative humidity,
non-condensing
Drop Specifications
Scanner withstands 18 drops from 1.5 meters (5.0 feet) to
concrete
Ambient Light Immunity
Up to 86,000 Lux
22
QuickScan™ QD2430
LED and Beeper Indications
Contaminants Spray/rain
Dust/particulates
IEC 529-IP42
(IP51 QD2430-E model only)
ESD Level
16 KV
Regulatory
Electrical Safety
UL 60950, CSA C22.2 No. 60950, IEC 60950
EMI/RFI
North America (FCC) : Part 15 Class B; Canada ( IC) : ICES003 Class B; Russia ( Gost); European Union EMC Directive;
VCCI-Japan; Korean KCC; Taiwan EMC (BSMI);
Australia (ACMA); Mexico (NOM)
LED and Beeper Indications
The reader’s beeper sounds and its top multi-colour LED illuminates to indicate various functions or errors on the reader.
An optional “Green Spot” also performs useful functions. The
following tables list these indications. One exception to the
behaviors listed in the tables is that the reader’s functions are
programmable, and so may or may not be turned on. For
example, certain indications such as the power-up beep can
be disabled using programming bar code labels.
Indicator
Description
Power-up Beep
The reader is in the process of powering-up.
LED
Reader beeps four
times at highest frequency and volume
upon power-up.
Good Read Beep
A label has been successfully scanned by
the reader.
LED behavior for this
indication is configurable via the feature
“Good Read: When to
Indicate”
(see the PRG for information.)
ROM Failure
There is an error in the
reader's software/programming
Flashes
Quick Reference Guide
Beeper
The reader will beep
once at current frequency, volume,
mono/bi-tonal setting and duration
upon a successful
label scan.
Reader sounds one
error beep at highest
volume.
23
LED and Beeper Indications
Indicator
Description
LED
Beeper
N/A
Reader 'chirps' six
times at the highest
frequency and current
volume.
Limited Scanning
Label Read
Indicates that a host
connection is not
established.
Reader Active Mode
The reader is active and
The LED is lit steadilya
ready to scan.
N/A
Reader
Disabled
The reader has been
disabled by the host.
The LED blinks continuously
N/A
N/A
N/A
Upon successful read of
a label, the software
Green Spota flashes shall turn the green
momentarily
spot on for the time
specified by the configured value.
aExcept when in sleep mode or when a Good Read LED Duration other than 00 is selected
24
QuickScan™ QD2430
LED and Beeper Indications
Programming Mode - The following indications ONLY occur
when the reader is in Programming Mode.
INDICATION
DESCRIPTION
LED
BEEPER
Label Programming
Mode Entry
A valid programming label LED blinks contin- Reader sounds four
has been scanned.
uously
low frequency beeps.
Label Programming
Mode Rejection of
Label
A label has been rejected.
N/A
Reader sounds three
times at lowest frequency and current
volume.
Label Programming
Mode Acceptance of
Partial Label
In cases where multiple
labels must be scanned to
program one feature, this
indication acknowledges
each portion as it is successfully scanned.
N/A
Reader sounds one
short beep at highest
frequency and current volume.
Label Programming
Mode Acceptance of
Programming
Configuration option(s)
have been successfully programmed via labels and
the reader has exited Programming Mode.
N/A
Reader sounds one
high frequency beep
and 4 low frequency
beeps followed by
reset beeps.
Label Programming
Mode Cancel Item
Entry
Cancel label has been
scanned.
N/A
Reader sounds two
times at low frequency and current
volume.
Quick Reference Guide
25
Error Codes
Error Codes
Upon startup, if the reader sounds a long tone, this means the
reader has not passed its automatic Selftest and has entered
FRU (Field Replaceable Unit) isolation mode. If the reader is
reset, the sequence will be repeated. Press and release the
trigger to hear the FRU indication code.
The following table describes the LED flashes/beep codes
associated with an error found.
26
Number
of LED
Flashes/
Beeps
Error
1
Configuration
2
Interface PCB
6
Digital PCB
11
Imager
Corrective Action
Contact Helpdesk for assistance
QuickScan™ QD2430
Cleaning
Cleaning
Exterior surfaces and scan windows exposed to spills,
smudges or debris require periodic cleaning to ensure best
performance during scanning.
Use a soft, dry cloth to clean the product. If the product is very
soiled, clean it with a soft cloth moistened with a diluted nonaggressive cleaning solution or diluted ethyl alcohol.
Do not use abrasive or aggressive cleansing
agents or abrasive pads to clean scan windows
or plastics.
Do not spray or pour liquids directly onto the
CAUTION unit.
Quick Reference Guide
27
Regulatory Information
Regulatory Information
All models are designed to be compliant with rules and regulations in locations they are sold and will be labeled as
required.
Any changes or modifications to equipment, not expressly
approved by Datalogic could void the user's authority to operate the equipment.
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
FCC Class B Compliance Statement
The user is cautioned that changes or modifications not
expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
28
•
Increase the separation between the equipment
and receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio or television technician for help.
QuickScan™ QD2430
Regulatory Information
Canadian Notice
This equipment does not exceed the Class B limits for radio
noise emissions as described in the Radio Interference Regulations of the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils
numeriques de la classe B prescrites dans le Reglement sur le
brouillage radioelectrique edicte par le ministere des Communications du Canada.
CAUTION
Do not attempt to open or otherwise service any
components in the optics cavity. Opening or servicing any part of the optics cavity by unauthorized personnel may violate safety regulations.
Power Supply
This device is intended to be connected to a UL Listed/CSA
Certified computer which supplies power directly to the
reader or else be supplied by UL Listed/CSA Certified Power
Unit marked “Class 2” or LPS power source rated 5-14V minimum 900mA.
QD2430 can be powered by either a 5V or 12V power supply.
Características de la fuente
de alimentación eléctrica.
5V
Atencíon
Entrada:
100 - 240 Vca
350 mA, 50-60 HZ
Salida:
5VDC, 2.5A ?
(-)Negativo al centro
Entrada:
Salida:
12 V
100 - 240 Vca
600 mA, 50-60 HZ
12VDC, 1500mA ?
(-)Negativo al centro
Utilice en su red solo fuentes certificadas en Argentina.
El uso de fuentes de alimentación no compatibles puede resultar
en riesgo de incendio o de choque eléctrico para el usuario.
Quick Reference Guide
29
Regulatory Information
Imager Labeling
Sample labels are shown here to illustrate their location only.
Please view the labels on your product for actual details, as
they may vary from those depicted.
Scanner Regulatory
CAUTION
30
The QuickScan™ Handheld Reader is not userserviceable. Opening the case of the unit can
cause internal damage and will void the warranty.
QuickScan™ QD2430
Regulatory Information
WEEE Statement
Waste Electrical and Electronic Equipment
(WEEE) Statement
English
For information about the disposal of Waste Electrical and
Electronic Equipment (WEEE), please refer to the website at
www.datalogic.com.
Italian
Per informazioni sullo smaltimento delle apparecchiature
elettriche ed elettroniche consultare il sito Web
www.datalogic.com.
French
Pour toute information relative à l’élimination des déchets
électroniques (WEEE), veuillez consulter le site internet
www.datalogic.com.
German
Informationen zur Entsorgung von Elektro- und ElektronikAltgeräten (WEEE) erhalten Sie auf der Webseite
www.datalogic.com.
Spanish
Si desea información acerca de los procedimientos para el
desecho de los residuos del equipo eléctrico y electrónico
(WEEE), visite la página Web www.datalogic.com.
Portuguese
Para informações sobre a disposição de Sucatagem de
Equipamentos Elétricos e Eletrônicos (WEEE -Waste Electrical
and Electronic Equipment), consultar o site web
www.datalogic.com.
Chinese
有关处理废弃电气电子设备 (WEEE) 的信息, 请参考 Datalogic 公司的网站 www.datalogic.com。
Japanese
廃電気電子機器 (WEEE) の処理についての関連事項は
Datalogic のサイト www.datalogic.com をご参照下さい。
Quick Reference Guide
31
32
X
X
X
⬉䏃ᵓ㒘ӊ
‫ܝ‬ᄺ㒘ӊ
‫ܝ‬ᄺ㒘ӊ
Printed Circuit Board Assembly
Assy, Optics Block
Assy, Module
O
O
O
ᳮ
Mercury
(Hg)
O
O
O
叏
Hexavalent
Chromium
(Cr(VI))
O
O
O
౐ચ卲
O
O
O
ᄙᄽ侶૖
O
O
O
ᄙᄽԲ૖ㅘ
Polybrominated
diphenyl ethers
(PBDE)
China RoHS
Polybrominated
biphenyls
(PBB)
᦭Ქ᦭ኂ‛凝ᚗర⚛
Cadmium
(Cd)
Oઍ⴫ᱝẊㇱઙ⊛ᚲ᦭ဋ凝‫ޗ‬றխࢬܶऱ具Ẋ‫ڶ੅ڶ‬୭ढ凝݁‫܅‬Պխ䦀Գ‫ا‬٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛
‫ޝ‬䶣՗ॾஒ䣈঴խ‫ڶ੅ڶ‬୭ढ凝ऱૻၦ૞‫ޣ‬ρ(SJ/T 11363-2006) 億ࡳऱૻၦ‫ޕ‬
X:ઍ⴫ᱝẊㇱઙᚲ↪⊛ဋ凝‫ޗ‬றխ, ⥋ዋ᦭৻㮕᧚ᢱ౔ᚲ฽⊛᦭Ქ᦭ኂ‛凝೏Պխ䦀Գ‫ا‬٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛
‫ޝ‬䶣՗ॾஒ䣈঴խ‫ڶ੅ڶ‬୭ढ凝ऱૻၦ૞‫ޣ‬ρ(SJ/T 11363-2006) 億ࡳऱૻ㊂
卋
ㇱઙฬ⒓
PART
Lead
(Pb)
Regulatory Information
China RoHS Table of Restricted Elements
QuickScan™ QD2430
Regulatory Information
Datalogic ADC
Limited Factory Warranty
Warranty Coverage
Datalogic warrants to Customer that Datalogic's products will be free
from defects in materials and workmanship for a period of five years
from product shipment. Datalogic ADC (“Datalogic”) hardware products are warranted against defects in material and workmanship under normal and proper use. The liability of Datalogic under this
warranty is limited to furnishing the labor and parts necessary to
remedy any defect covered by this warranty and restore the product
to its normal operating condition. Repair or replacement of product
during the warranty does not extend the original warranty term.
Products are sold on the basis of specifications applicable at the time
of manufacture and Datalogic has no obligation to modify or update
products once sold.
If Datalogic determines that a product has defects in material or
workmanship, Datalogic shall, at its sole option repair or replace the
product without additional charge for parts and labor, or credit or refund the defective products duly returned to Datalogic. To perform repairs, Datalogic may use new or reconditioned parts, components,
subassemblies or products that have been tested as meeting applicable specifications for equivalent new material and products. Customer will allow Datalogic to scrap all parts removed from the
repaired product. The warranty period shall extend from the date of
shipment from Datalogic for the duration published by Datalogic for
the product at the time of purchase (Warranty period). Datalogic warrants repaired hardware devices against defects in workmanship and
materials on the repaired assembly for a 90 day period starting from
the date of shipment of the repaired product from Datalogic or until
the expiration of the original warranty period, whichever is longer. Datalogic does not guarantee, and it is not responsible for, the maintenance of, damage to, or loss of configurations, data, and applications
on the repaired units and at its sole discretion can return the units in
the “factory default” configuration or with any software or firmware
update available at the time of the repair (other than the firmware or
software installed during the manufacture of the product). Customer
accepts responsibility to maintain a back up copy of its software and
data.
Warranty Claims Process
In order to obtain service under the Factory Warranty, Customer must
notify Datalogic of the claimed defect before the expiration of the applicable Warranty period and obtain from Datalogic a return authorization number (RMA) for return of the product to a designated
Datalogic service center. If Datalogic determines Customer’s claim is
valid, Datalogic will repair or replace product without additional
charge for parts and labor. Customer shall be responsible for packaging and shipping the product to the designated Datalogic service center, with shipping charges prepaid. Datalogic shall pay for the return
of the product to Customer if the shipment is to a location within the
country in which the Datalogic service center is located. Customer
shall be responsible for paying all shipping charges, duties, taxes, and
any other charges for products returned to any other locations. Failure to follow the applicable RMA policy, may result in a processing fee.
Customer shall be responsible for return shipment expenses for
products which Datalogic, at its sole discretion, determines are not
Quick Reference Guide
33
Regulatory Information
defective or eligible for warranty repair.
Warranty Exclusions
The Datalogic Factory Warranty shall not apply to:
(i)
any product which has been damaged, modified, altered,
repaired or upgraded by other than Datalogic service personnel or its authorized representatives;
(ii) any claimed defect, failure or damage which Datalogic
determines was caused by faulty operations, improper use,
abuse, misuse, wear and tear, negligence, improper storage
or use of parts or accessories not approved or supplied by
Datalogic;
(iii) any claimed defect or damage caused by the use of product
with any other instrument, equipment or apparatus;
(iv) any claimed defect or damage caused by the failure to provide proper maintenance, including but not limited to cleaning the upper window in accordance with product manual;
(v) any defect or damage caused by natural or man-made
disaster such as but not limited to fire, water damage, floods,
other natural disasters, vandalism or abusive events that
would cause internal and external component damage or
destruction of the whole unit, consumable items;
(vi) any damage or malfunctioning caused by non-restoring
action as for example firmware or software upgrades, software or hardware reconfigurations etc.;
(vii) the replacement of upper window/cartridge due to scratching, stains or other degradation and/or
(viii) any consumable or equivalent (e.g., cables, power supply,
batteries, keypads, touch screen, triggers etc.).
No Assignment
Customer may not assign or otherwise transfer its rights or obligations under this warranty except to a purchaser or transferee of product. No attempted assignment or transfer in violation of this
provision shall be valid or binding upon Datalogic.
DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, ORAL OR WRITTEN, STATUTORY OR
OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE
FOR ANY DAMAGES SUSTAINED BY CUSTOMER ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UNDER THE
ABOVE. THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT IS
THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY
CLAIMS. UNDER NO CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO
CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY
INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT
DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE
NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit to
Datalogic. Datalogic shall assume risk of loss or damage for product
in Datalogic’s possession. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the
carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment.
34
QuickScan™ QD2430
Ergonomic Recommendations
Ergonomic Recommendations
CAUTION
In order to avoid or minimize the potential risk
of ergonomic injury follow the recommendations
below. Consult with your local Health & Safety
Manager to ensure that you are adhering to your
company’s safety programs to prevent employee
injury.
•
Reduce or eliminate repetitive motion
•
Maintain a natural position
•
Reduce or eliminate excessive force
•
Keep objects that are used frequently within easy
reach
•
Perform tasks at correct heights
•
Reduce or eliminate vibration
•
Reduce or eliminate direct pressure
•
Provide adjustable workstations
•
Provide adequate clearance
•
Provide a suitable working environment
•
Improve work procedures.
Quick Reference Guide
35
Services and Support
Services and Support
Datalogic provides several services as well as technical support through its website. Log on to www.datalogic.com and
click on the links indicated for further information.
Products
Search through the links to arrive at your product page where
you can download specific Manuals and Software & Utilities,
including:
Datalogic Aladdin™, a multi-platform utility program
•
that allows device configuration using a PC. It provides RS-232 interface configuration as well as
configuration bar code printing.
Service & Support
•
Technical Support - Product documentation and
programming guides and Technical Support
Department in the world
•
Service Programs - Warranty Extensions and Main-
•
Repair Services - Flat Rate Repairs and Return
•
Downloads – Manuals & Documentation, Data
tenance Agreements
Material Authorization (RMA) Repairs
Sheets, Product Catalogues, etc.
Contact Us
•
36
Information Request Form and Sales & Service
Network
QuickScan™ QD2430
Services and Support
NOTES
Quick Reference Guide
37
Services and Support
NOTES
38
QuickScan™ QD2430
DECLARATION OF CONFORMITY
13
Datalogic ADC Srl, Via S. Vitalino, 13
Lippo di Calderara di Reno (BO) 40012 Italy
EC-085
Rev.: 0
Pag.: 1 di 1
La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva di
Datalogic ADC Srl per:
This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC Srl
for:
Cette déclaration de conformité est établie sous la seule responsabilité de Datalogic Srl
pour:
Diese Konformitätserklärung wird unter der alleinigen Verantwortung des Datalogic ADC
Srl erteilt für:
Esta declaración de conformidad se expide bajo la exclusiva responsabilidad de Datalogic
ADC Srl para:
QUICKSCAN QD2430
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
2004/108/EC EMC Directive
2011/65/EC RoHS Directive
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica
ed alla sicurezzadei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.
Basée sur la législation des Etats membres relative à la compatibilté électromagnétique et
à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische
Verträglichkeit und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022 ( CLASS B ITE ),
SEPTEMBER 2006:
AMENDMENT A1 ( CLASS B ITE ),
OCTOBER 2007:
EN 55024, SEPTEMBER 1998;
AMENDMENT A1:2001+A2:2003:
LIMITS AND METHODS OF MEASUREMENTS OF
RADIO DISTURBANCE
CHARACTERISTICS OF INFORMATION TECHNOLOGY
EQUIPMENT
INFORMATION TECHNOLOGY EQUIPMENT
IMMUNITY CHARACTERISTICS
LIMITS AND METHODS OF MEASUREMENT
EN 50581, SEPTEMBER 2012:TECHNICAL DOCUMENTATION FOR THE ASSESSMENT OF
ELECTRICAL AND ELECTRONIC PRODUCTS WITH RESPECT TO
THE RESTRICTION OF HAZARDOUS SUBSTANCES
Lippo di Calderara, March29th ,
2013
Ruggero Cacioppo
Quality Assurance Manager
www.datalogic.com
©2013-2014 Datalogic ADC, Inc. • All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S.A. and the E.U.
Datalogic ADC, Inc.
959 Terry Street | Eugene |OR 97402 | USA
Telephone: (1) 541-683-5700 | Fax: (1) 541-345-7140
820056914
(Rev B)
Sept 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement