IP Phone Quick Guide - Fine Line Communications

IP Phone Quick Guide - Fine Line Communications
IP Phone
Quick Guide
LIP-8008E
Please read this manual carefully before operating your set.
Retain it for future reference.
P/NO : MMBB9235305
NOV/2011/ISSUE 1.0
Printed in Thailand
LIP-8008E Quick Guide
ST
Important Safety information
To prevent the risk of harm to the user or damage to equipment, please read this
information before installing or repairing the phone.
1. Only trained and qualified service personnel should install, replace or service the phone.
2. Don’t spill liquid (ex. Water) on the phone. In case of spill, contact your service
technician for assistance to avoid fire or electric shock.
3. If you see smoke or smell something burning, unplug the power cord and the phone line.
Call your service technician for assistance.
4. Don’t use the phone during a thunderstorm. Lightning strike may result in a fire, severe
electrical or acoustic shock.
5. Don’t tug the power cord or the phone line. This may result in a fire, an electric shock or
equipment damage.
6. Ensure that children do not pull on phone cords. This may injure children or result in
equipment damage.
7. The ear-piece houses a magnetic device which may attract pins or small metal objects.
Keep handset clear of such objects and check before use.
8. Avoid placing the phone in an area that is dusty, damp or subject to vibration.
9. Choose a site that is dry and well ventilated.
10. Don’t put the heavy things on the phone.
11. Do not drop or throw the phone.
12. Static electricity discharge will damage electronic components.
13. Keep out of direct sunlight and away from heat.
14. Clean the phone with a soft, dry cloth only. Do not use volatile liquids such as petrol,
alcohol or acetone as this may cause a fire or result in discoloration or damage to
plastics. Do not clean with wax or silicon products as these may enter the equipment and
cause operation to become unreliable.
15. No user serviceable parts inside. Do not inset a screw driver or any metal objects into
the phone. This may cause electric shock or damage the equipment and will render the
warranty void.
Copyright© 2011 LG-Ericsson Co., Ltd. All Rights Reserved
This material is copyrighted by LG-Ericsson Co., Ltd. Any unauthorized reproductions, use or
disclosure of this material, or any part thereof, is strictly prohibited and is a violation of Copyright
Laws. LG-Ericsson reserves the right to make changes in specifications at any time without
notice. The information furnished by LG-Ericsson in this material is believed to be accurate and
reliable, but is not warranted to be true in all cases.
1
LIP-8008E Quick Guide
ST
Regulatory information
European Union Declarations of Conformity
LG-Ericsson Co., Ltd. declare that the equipment specified in this document bearing the “ CE” mark
conforms to the European Union Radio and Telecommunications Terminal Equipment Directive(R&TTE
1999/5/EC), including
the Electromagnetic Compatibility Directive(2004/108/EC) and Low Voltage
Directive(2006/95/EC).
Copies of these Declarations of Conformity (DoCs) can be obtained by contacting your local sales
representative.
FCC/IC Interference Statement : USA / CSA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 /RSS-GEN of the FCC/IC rules. Operation is subject to the following
two conditions:
(1)This device may not cause harmful interference; and (2) This device must accept any interference
received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The use of this device in a system operating either partially or completely outdoors may require the user
to obtain a license for the system according to the Canadian regulations.
CAUTION : Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the
equipment.
2
LIP-8008E Quick Guide
ST
Fixed Feature Button Definitions
DND – Blocks all incoming calls; red LED illuminates.
Speed – Access speed dialing, speed programming.
Vol   – Adjusts volume for ringing, headset, and speakerphone; adjusts LCD brightness (in
idle state).
Trans/PGM –Initiates call transfer, or enters programming mode.
Hold/Save – Places active call on hold or saves programming information.
Speaker – Toggle to activate; red LED illuminates.
Call Back – Initiates call back request when calling a busy station; call is completed when
busy station returns to idle status.
3 Soft Buttons – Used with fixed and flexible features; use changes in relation to LCD display.
Flexible buttons – Some are system pre-programmed for line appearance, and some are
user programmable.
Ring/MSG Indicator – Illuminates when ringing, or message waiting.
LCD Display – Phone interface for status, dialing directories, and text message information.
Hands-free Microphone – Used for hands-free speakerphone function.
3
LIP-8008E Quick Guide
ST
LIP-8008E Keyset User Operation
The following is provided as quick reference for commonly used features/functions. Complete
instructions are included in the User Guide.
Placing a Call:
ICM Line –
 Lift handset or press SPEAKER button.
 Dial the extension number from the keypad.
CO Line –
 Lift handset or press SPEAKER button.
 Press CO/IP line, or dial access number.
 Dial desired phone number.
Using Camp-On (Call-Wait):
 When calling a busy Station, press *.
 Wait for party to answer.
(iPECS-CM/MG)
 Call a busy Station.

Press [TRANS/PGM] button and dial Camp-On Register Code.
To retry a busy external number until answered:
 When placing an outgoing call to a busy party, press the REDIAL Soft button.
 Hang-up handset; the call will be retried until the call is connected or the feature is
cancelled.
(iPECS-CM/MG)
 When placing an outgoing call to a busy party, press the ACNRL Soft button.
 Hang-up handset; the call will be completed when busy party returns to idle state.
4
LIP-8008E Quick Guide
ST
Delete ACNR:
 Press the STOP Soft button in idle state.
Answering a Call while idle:
ICM Line –
 Lift handset, or if in HF mode, just speak.
CO Line –
 Lift handset, and press flashing Flex button (as needed).
Using Do Not Disturb (DND):
 Press the DND button (toggles ON and OFF).
Pickup a Call to another Station:
 Lift handset.
 Dial Directed Call Pick-up Code.
 Dial the intercom number of the ringing station.
Pickup a Call from another Station in your Group:
 Lift the handset.
 Dial Group Call Pickup code.
Conference:
A Conference flex button should be programmed.
 Place a call to first member.
 If first member answer, press Conf flex button and place a call to second member.
 If last member answer, press Conf flex button, twice.
* For conference more than 4 members in iPECS-LIK System, MCIM board is needed.
(iPECS-CM/MG)
 Place a call to first member.
 If first member answer, press Conference flexible button and place a call to second
member.
* For conference more than 4 members in iPECS-LIK, VPCM board is needed.
* For conference members, VOIB(VOIU) board is always needed in iPECS-MG.
5
LIP-8008E Quick Guide
ST
Call Hold:
 Press the HOLD/SAVE button while on a CO call.
 Press the flashing CO button or Loop button to rejoin call.
Call Forward:
 Lift handset or press SPEAKER button.
 Press FWD soft button.
 Dial the type of forward code (0-5, SBG:0-4).
1=Unconditional, 2=Busy, 3=No Answer, 4=Busy/No Answer, 5=Incoming CO Offnet
(Attendant only), 0=remote
 For Forward code 1-4, dial destination number.
 For Forward code 5, press CO/CO-Group button, and dial Speed number.
 For Forward code 0, dial password of forwarded station and enter the Forward code (1-4).
1=Unconditional, 2=Busy, 3=No Answer, 4=Busy/No Answer.
- Dial the destination number.
(iPECS-CM/MG)
 Lift handset.
 Press FWD soft button and dial the type of forward code (0-4).
1=Unconditional, 2=Busy, 3=No Answer, 4=Busy/No Answer , 0=Remote
 For Forward code 1-4, dial destination number.
 For Forward code 0, dial forwarded station number, password and *.
 Dial the destination number.
Delete Call Forward:

Lift handset or press SPEAKER button.

Press the FWD soft button.

Dial #.
Call Transfer:

While on an active call, press the TRANS/PGM button.

Place call to the transfer destination.

Remain on the line to announce the call and/or hang-up to complete the transfer.
6
LIP-8008E Quick Guide
ST
Storing Speed Dial Numbers:
 Press the Trans/PGM and Speed button.
 Dial Speed bin number.
 Press CO button or dial CO access code
 Dial telephone number you wish to store.
 Press the Hold/Save button.
 Enter the name associated to the number.
 Press the Hold/Save button; a confirmation tone will be heard.
(iPECS-CM/MG)
 Press the Speed button.
 Press ADD Soft button.
 Dial Speed bin number
 Dial CO access code and telephone number you wish to store.
 Press the Hold/Save button.
 Enter the name associated to the number.
 Press the Hold/Save button; a confirmation tone will be heard.
Using Speed Dial Numbers:
 Press the Speed button.
 Dial the desired Speed dial bin number.
LIP-8008E Installation
Note: LIP-8008E IP-Phone can be powered by either AC adaptor or Power over Ethernet (PoE,
class 1). To use AC power, use only the LG-Ericsson Approved AC power adaptor, which you
can order separately. To use PoE, your connected LAN must support PoE.
<Important> Use either PoE or AC adaptor, not both, for power supply of your phone.
1. Plug one end of the supplied LAN cable into the LAN Ethernet port on the back of your IP
phone marked with the
symbol.
2. Plug the other end of the cable into your LAN Ethernet connection. (Do not extend the LAN
Ethernet cable to the outside of the building.)
3. (Optional) If you are connecting your PC Ethernet through the IP Phone, plug one end of the
LAN Ethernet cable into the PC Ethernet port on the back of your IP Phone marked with the
symbol.
<Important> Skip the following procedures from 5 to 6 if PoE is used for power supply
of your phone.
7
LIP-8008E Quick Guide
ST
4. (Optional) Plug the other end of the cable into your LAN Ethernet connection.
5. (Optional) Connect the AC power adapter (not supplied) to the AC adapter jack on the back of
your IP Phone. Fasten the cord with a hook to prevent it from being disconnected.
6. (Optional) Plug the AC power adapter into the nearest AC power outlet. The phone will start
up.
7. (Optional) for the wall-mounting, sleeve of the CAT5 cable should be moved backward to
prevent it protrude.
Flex Button Program
 Press the TRANS/PGM button.
 Press the flexible button to be programmed.
 Press TRANS/PGM button and User Program Code (refer to table).
 Press the HOLD/SAVE button.
(iPECS-CM/MG)
 Press the TRANS/PGM button.
 Press the flexible button and program type (1: Fixed button, 2: Number).
 Enter Number Plan Code, or
Enter Program Mode code and User Program Code
 Press the HOLD/SAVE button.
System User Program Codes (iPECS-LIK)
Code
Function
10
Enblock Mode Dialing
Remark
11
Intercom Ring
Select Ring Tone 1-8
12
CO/IP Ring
Select Ring Tone 1-8
13
Intercom Answer Mode
Select ICM Signal mode, 1:HF, 2:Tone, 3:Privacy
14
Call Coverage Attribute Setting
1:ON/OFF, 2:Ring Delay (0-9)
15
Station Ring Download
Ring Tone 5-8
21
Knock Down STA COS
22
Restore Station COS
Requires Auth Code
23
Walking COS
Require Auth Code
30
VM Mobile Notify
31
Station Wait Retrieve
8
LIP-8008E Quick Guide
Code
Function
32
CLI/IP Message Wait Retrieve
33
Authorization Code (Password) Entry
34
DID Call Wait Button
35
Message Wait in Exec/Sec Pair
36
Send SMS Message
37
Register Mobile Ext.
38
Activate Mobile Ext.
39
Register Mobile Ext. CLI
41
Set Wake Up Time
42
Erase Wake-Up Time
51
Custom/Pre-defined Message Display
52
Register Custom Message (Message 00)
53
Create Conf. Room
54
Delete Conf. Room
55
Monitor Conf-Group
61
Headset/Speakerphone
62
Headset Ring Mode
71
LCD Display Mode
72
Version Display
73
Background Music
74
Station Name Reg.
75
Display Phone IP Address
76
Change Phone IP Address
77
Display Phone MAC IP Address
79
Display Phone Version
80
RECORD Button
81
ISDN CLIR Button
82
ISDN COLR Button
84
Account Code Button
85
LOOP Button
86
ATD Intrusion Button
87
ICM Button
88
Camp-On Button
89
Keypad Facility Button
8#
OHVO Button
91
CONF Button
94
FLASH Button
95
MUTE Button
96
MONITOR Button
97
REDIAL Button
ST
Remark
Input up to 12 digits
Input time, 24-hr clock
Input up to 24 characters
1:Speakerphone, 2:Headset, 3:Both
Requires VSF/External SMDI VM
9
LIP-8008E Quick Guide
Code
Function
98
FWD Button
99
PTT Button
ST
Remark
9*
In Room Indication Button
*0
Hot Desk Login Code
**
Hot Desk Logout Code
*7
Force Fwd to Destination
Requires room number(01~10)
System User Program codes (iPECS-CM/MG)
Code
Function
Remark
11
Answer Mode(H/T/P)
Select ICM Signal mode, 1:HF, 2:Tone, 3:Privacy
12
Station Name Program
Input up to 12 characters
iPECS-CM:
Index(1-5) + Type(1~5, 1:Once, 2:Daily, 3:Mon~Fri,
4:Mon~Sat, 5:Date), + HHMM(24-hour clock) +
13
Set Wake Up
YYMMDD(If type is Date)
iPECS-MG:
HHMM(24-hour clock), # (repeat mode: once, repeat)
iPECS-CM:
Index(1-5)
14
Reset Wake Up
iPECS-MG:
1:ON/OFF, 2:Ring Delay (0-9)
15
Language Program
00 - 17
16
LCD Date Mode Change
DD/MM/YY or MM/DD/YY
17
LCD Time Mode Change
12 Hour/24 Hour
21
ICM Ring Type Program
22
CO Ring Type Program
23
Ring Download
24
Set BGM
Not Supported
31
Temporary COS Mode
Auth. Code required
32
Retrieve COS
Auth. Code required
33
Walking COS
Auth. Code required
34
Register Password
Auth. Code required
35
Call Log Protect
Auth. Code required
36
SMS Message Protect
Auth. Code required
41
Preselected MSG PGM
0-9, MSG / *: User Custom # Deactivation
5-8+0-9
10
LIP-8008E Quick Guide
Code
ST
Function
42
Set User Message
43
Send SMS MESSAGE
Remark
44
Received SMS MESSAGE
51
Mobile-Ext. Enable
52
Mobile-Ext. Number PGM
1-5
53
Mobile-Ext. CLI PGM
1-5
1-5
54
Create Conference Room
55
Delete Conference Room
61
Speaker/Headset PGM
Speaker/Headset
62
Headset Ring Program
Speaker/Headset/Both
71
Register Station ICLID
72
View Station ICLID
81
View IP Address
82
View Mac Address
83
View Keyset Version
80
Network Setting
91
MPB Version Display
Not used in CM
92
View IP Address
Not used in CM
System User Program Codes (SBG)
Code
Function
Remark
11
Intercom Answer Mode
Select ICM Signal mode, 1:HF, 2:Tone, 3:Privacy
12
Headset/Speakerphone mode
0:H, 1:S
13
Select Headset Ring type
1:S, 2:H, 3:Both
21
Set Wake-Up Time
Once/Permanent & Hour/Min
22
Erase Wake-Up Time
31
LCD Display Language
32
Sys version display
Domestic/English
33
Select BGM source
(0~1)
34
Station Name registration
Station Name
35
Display Phone IP Address
36
Display Phone MAC Address
37
Display Phone Version
38
Network Configuration
41
Forced Forward to Destination
42
Call Log Display
Station Group Number
11
LIP-8008E Quick Guide
Code
Function
43
CLIR Service
44
COLR Service
4*
LOOP button
ST
Remark
Button PGM only
50
CALLBACK button
Button PGM only
51
CONF button
Button PGM only
52
MUTE button
Button PGM only
53
ICM button
Button PGM only
54
REDIAL button
Button PGM only
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement