Advertisement
Advertisement
Getting Familiar with Your FuzzyScan
Thank you for choosing Cino FuzzyScan Bluetooth Cordless Image Scanner.
Powered by the combination of cutting-edge FuzzyScan Imaging Technology and Bluetooth wireless technology, it not only provides outstanding reading performance, but also delivers the convenience and freedom of mobility. It’s ideal for a broad range of applications to unleash your productivity with ease.
This document provides a quick reference for installation and operation. The complete documentation is available at www.cino.com.tw.
A770BT Series
Link Indicator
Status Indicator
Beeper
Scan Window
Trigger
Battery Cavity
End Cap
F780BT & L780BT F680BT & L680BT
HB211x Smart Cradle
HB2100 USB Charging Cradle
Central Indicator
Side Indicators
Paging/Reset Button
USB Bus Power Switch
Host Interface Port
DC Power Jack
Central Power Indicator
Reserved
USB Bus Power Switch
USB Port
DC Power Jack
1
Preparations before Using
Install the Battery
Ensure the battery contacts of the battery pack are facing the charging contacts inside the battery cavity.
Slide the battery pack into the battery cavity until hearing a click sound before locking it with the end cap. The scanner will give 4 beeps when the battery pack is installed properly if the battery
Charge the Battery
pack still has power.
Secure the end cap with the screw provided.
Use USB Bus Power
Choose an appropriate plug and slot it into the power adapter cavity until it is locked. Then plug the AC power plug into the AC wall socket.
Plug the DC power cord of power supply unit into the DC Jack of the cradle. The smart cradle emits the power-on beeps and the central indicator gives one blue blink. If you use the charging cradle, the central power indicator turns steady blue.
Place the scanner on the cradle. The status indicator of scanner turns steady red if the battery is not fully charged. When the battery is fully charged, the status indicator of scanner turns steady green.
Please charge the new battery pack for 8 hours before its first use.
If USB 3.0 is available in your host device, both battery charging and regular operation can be supported by the USB Bus Power without using external power supply.
If only USB 2.0 is available in your host device, we recommend using external power supply as power source, because the power supplied from
USB2.0 is not enough to support both battery charging and regular operation simultaneously.
If you want to use this feature, please slide the
USB bus power switch to “ON”. Then connect the cradle to the host device via USB cable.
2
Decide Your Radio Link Mode
The FuzzyScan Bluetooth image scanner provides several radio link modes to communicate with most host devices. When the Bluetooth-enabled host device is not available, it can work with the smart cradle in PAIR mode
(peer-to-peer connection) or PICO mode (multiple connections) to provide a
plug-and-play cordless migration of your existing non-Bluetooth-enabled devices. Moreover, you are also able to use the scanner to work with
Bluetooth-enabled host devices via SPP mode or HID mode.
When the radio link is disconnected, the scanner is capable of reconnecting the radio link automatically when it returns to the communication coverage.
But please note that this feature is not available in SPP slave mode. If you would like to change the radio link mode, please scan the “Uninstall” command to reset the scanner to uninstall state.
PAIR Mode
If the Bluetooth device is not available in your existing system, PAIR mode is the simplest plug-and-play solution. In this mode, a smart cradle can only work with one scanner. The smart cradle not only provides the Bluetooth radio link with the scanner, but also offers the legacy cabled interfaces to the host device, including USB HID, USB COM, PS/2(DOS/V) Keyboard Wedge and RS232 Serial.
PICO Mode
For the requirement of multiple connections, up to 7 scanners can be connected to one smart cradle concurrently. If you would like to un-pair all scanners paired with the smart cradle, please press and hold the paging/reset button of the smart cradle for more than 5 seconds. If you just want to un-pair part of the paired scanners, please take those paired scanners to scan the “Uninstall” command one by one.
HID Mode
Through the most useful HID service, the scanner can work as a Bluetooth
Keyboard. In this mode, the scanner will be discoverable by the radio connection request issued by the remote host device. For some cases, you may be requested to enter the Passkey (PIN) to establish the Bluetooth connection for security purpose.
SPP Master/Slave Mode
Through the standard SPP service, the scanner can work as a Bluetooth
Serial Device. In SPP master mode, the scanner initiates the radio connection request to the remote slave device. In SPP slave mode, the scanner will be discoverable by the radio connection request issued by the remote host device.
3
Use FuzzyScan in PAIR Mode
Ensure the battery is fully charged. Please refer to the section of
Preparations before Using for details.
Please choose your desired interface cable, then plug it into the host interface port of the smart cradle and connect it to the host device.
USB PS/2 RS232
Turn on the power of your host device.
Please note that if the scanner is shipped together with a smart cradle, they are pre-paired already. You will see the link indicator of scanner gives 1 blue blink per 2.5 seconds and the central indicator of smart cradle turns steady blue. If the scanner and smart cradle just give
alternative red and green blinks (“Uninstall” state), please follow step
5 to establish the connection between scanner and smart cradle.
Scan “PAIR mode” command. The status indicator of scanner will turn steady red immediately.
Uninstall
Place the scanner on the smart cradle, then you will hear one short beep to indicate the pairing process is activated. The scanner will emit continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing process. When you hear 4 beeps in ascending tone, the pairing process is completed. You will see that the link indicator of scanner gives 1 blue blink per 2.5 seconds and the central indicator of the smart cradle turns steady blue.
If the scanner pairing process failed or it’s not placed on the smart cradle within 20 seconds, you will hear 2 “Di-do Di-do” beeps to warn the failure of pairing, the scanner will return to uninstall state automatically.
Scan the corresponding host interface quick set command to complete the installation.
The default host interface of smart cradle is preset to USB HID. If you want to set the host interface to USB COM, you have to install the
USB virtual COM driver into your host device before using the scanner. Please visit CINO website to download the driver
4
Use FuzzyScan in PICO Mode
Ensure the battery is fully charged and choose your desired interface cable, then plug it into the host interface port of the smart cradle and connect it to the host device.
USB PS/2 RS232
Turn on the power of your host device.
Ensure the side indicators of the smart cradle give alternative red and
green blinks (in “Uninstall” state). If the smart cradle is paired with other scanners, please press and hold the paging/reset button for more than 5
seconds to un-pair all paired scanners. Then the smart cradle will return to uninstall state automatically.
Prepare the scanners you desire to pair with the smart cradle. Ensure the status indicator of each scanner give alternative red and green blinks
(in “Uninstall” state). If the scanner is not in uninstall state, please scan the “Uninstall” command to un-pair the scanner, then scan the “PICO mode” command, and the status indicator of scanner will turn steady red.
Uninstall
Place the scanner on the smart cradle, then you will hear one short beep to indicate the pairing process is activated. The scanner will emit continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing process. When you hear 4 beeps in ascending tone, the pairing process is completed. You will see that the link indicator of scanner gives 1 blue blink per 2.5 seconds, the central indicator of the smart cradle turns steady blue and its side indicators turn steady
green.
If the scanner pairing process failed or it’s not placed on the smart cradle within 20 seconds, you will hear 2 “Di-do Di-do” beeps to warn the failure of pairing, the scanner will return to uninstall state automatically.
Please scan the corresponding host interface quick set command to complete the installation. Then repeat the same procedures to pair other scanners with the smart cradle.
For user’s convenience, the smart cradle will automatically assign the
ID numbers to each scanner. Please scan the System Information command to check the assigned ID number of each scanner.
5
Use FuzzyScan in HID Mode
Ensure the battery is fully charged. Power on the scanner within radio coverage and ensure the status indicator of scanner gives alternative
red and green blinks (in “Uninstall” state). If the scanner is not in uninstall state, please scan the “Uninstall” command first.
Uninstall
If your remote host is equipped with latest Bluetooth drivers, or it’s an iOS or Android device, you are recommended to use “HID Mode” for quick paring. If necessary, you may use “HID Mode with Passkey” to establish a more secure connection. If you frequently experienced the problem in using HID mode, please try “HID Legacy Mode” instead.
HID Legacy Mode HID Mode with Passkey
Once you scan one of above commands, the link indicator of scanner will give 3 blue blinks per 2 seconds during searching process. You have to execute the Bluetooth Discovery procedure to find available Bluetooth device, then select “F(L/A)xxxBT-xxxx”.
If you use “HID Mode”, please go to step 5.
If you use “HID Mode with Passkey”, you will be requested to enter the
Passkey (PIN) on the remote host. Please enter the Passkey (PIN) accordingly by scanning the “Option Code” (page 13), and then scan the
“FIN (Finish)” to end the Passkey entry, then go to step 5.
If you scan “HID Legacy Mode”, the Passkey (PIN) may be requested.
Please enter “00000000” (default setting), you will see “Keyboard on
F(L/A)xxxBT-xxxx”. Please double click this HID service to establish the connection between scanner and remote host device.
The scanner will emit 4 beeps in ascending tone to indicate the connection is established. At the same time, the link indicator of scanner will give 1 blue blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within
1 minute after scanning the above command, the scanner will go to sleep automatically. You can just press the trigger to wake up the scanner to continue the installation.
The installation procedure may vary depending on different remote host devices, operating systems and the Bluetooth drivers.
Please consult your professional IT consultant to obtain necessary support.
For more detailed information, please visit CINO website.
6
Use FuzzyScan in SPP Mode
Establish SPP Master Connection
Ensure the battery is fully charged. Please go to the folder “Hardware” located in Bluetooth Advanced Setting of the remote host device to check its device MAC address. Then prepare a 12-character Code 128 barcode of the remote host device MAC address, or follow the step 4 to input MAC address by scanning 12 option codes.
Ensure a virtual COM port is available in your remote host for connecting the scanner. If not, please go to the folder “Local Services” located in
Bluetooth Advanced Setting. Click the “Add Serial Services” to add one more Bluetooth COM port.
Power on the scanner within radio coverage and ensure the status indicator of scanner gives alternative red and green blinks (in
“Uninstall” state). If the scanner is not in uninstall state, please scan the
“Uninstall” command first, then scan the “SPP Master Mode” command.
The status indicator of scanner will turn steady red immediately.
Uninstall
SPP Master Mode
Scan a 12-character MAC address barcode. The scanner will emit continuous short clicks and the link indicator of the scanner will flash blue quickly during the radio connecting process. If the Passkey (PIN) is requested, please enter “00000000” (default setting).
The scanner will emit 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of scanner will give 1 blue blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner failed to connect to the host device within
30 seconds, the link indicator will give 3 blue blinks per 2 seconds. But the scanner is still continuing to discover the host device for another 30 seconds before go to sleep. In the interim, you still can scan “Uninstall” command to resume the scanner to uninstall state. If the scanner went to sleep already, you can just press the trigger to wake up the scanner to continue the installation.
The above procedures are based on popular Windows environment.
But the installation procedure may vary depending on different remote host devices, operating systems and the Bluetooth drivers. Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during the installation processes.
For more detailed information, please visit CINO website.
7
Establish SPP Slave Connection
Ensure the battery is fully charged and a virtual COM port is available in your remote host for connecting the scanner. If not, please go to the folder “Client Applications” located in Bluetooth Advanced Setting. Click the “Add COM Port” to add one more Bluetooth COM port.
Power on the scanner within radio coverage and ensure the status indicator of scanner gives alternative red and green blinks (in
“Uninstall” state). If the scanner is not in uninstall state, please scan the
“Uninstall” command first, and then scan the “SPP Slave Mode” command. The link indicator of scanner will give 3 blue blinks per 2 seconds during searching process.
Uninstall
SPP Slave Mode
You have to execute the Bluetooth Discovery procedure to find all available Bluetooth device list in your remote host. You will see
‘’F(L/A)xxxBT-xxxx’’ is shown in the list if the scanner is successfully discovered.
Double click the “F(L/A)xxxBT-xxxx” on the discovered Bluetooth devices.
If the Passkey (PIN) is requested,, please enter “00000000” (default setting). You will see “Serial Port on F(L/A)xxxBT-xxxx”. Please double click this SPP service to establish the connection between scanner and remote host device.
The scanner will emit 4 beeps in ascending tone to indicate the connection is established. At the same time, the link indicator of scanner will give 1 blue blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within
1 minute after scanning the “SPP Slave Mode” command, the scanner will go to sleep automatically. You can just press the trigger to wake up the scanner to continue the installation.
The above procedures are based on popular Windows environment.
But the installation procedure may vary depending on different remote host devices, operating systems and the Bluetooth drivers. Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during the installation processes.
For more detailed information, please visit CINO website.
8
Out-of-range Scanning
When the radio connection is established between scanner and remote host device, the scanner will transmit each scanned data right after scanning the barcode. However, the scanner is preset not to scan any barcode data when it loses the radio connection with the remote host device.
If you enable the out-of-range scanning function, the scanner is able to continue scanning barcode data while it is out of radio coverage. All scanned data will be temporarily stored into the memory buffer until radio link resumed.
Enable Out-of-range Scanning
Disable Out-of-range Scanning
◆
In case of the scanner is out of radio coverage, you will hear 4 beeps in descending tone to indicate the radio connection lost. The link indicator of scanner will give 3 blue blinks per 2 seconds. Once the scanner is back to radio coverage, you will hear 4 beeps in ascending tone to indicate the radio connection rebuilt and the link indicator of scanner will give 1 blue blink per
2.5 seconds. At the same time, all stored scanned data will be transmitted automatically right after the radio link is resumed.
Presentation Scanning
The Presentation Scanning is designed for hand-free applications for user’s convenience. If the “Presentation Scanning Auto-sense” function is enabled, the scanner is capable of automatically switching to presentation mode as soon as you place it onto the SmartStand or cradle.
Enable Auto-sense
◆
Sleep Mode & Power Off
The scanner is preset to enter “Sleep Mode” if the scanner is not used after time-out duration. When the scanner is under sleep mode, it is preset to enter
“Power Off” automatically if it’s not woke up after time-out duration.
If you want your scanner to enter “Sleep Mode” or “Power Off” immediately, please scan “Sleep Mode” or “Power Off” command. If you would like to wake up the scanner, please press the trigger button.
Sleep Mode
Off
9
Batch Scanning (Inventory Mode)
Thanks to the specially designed Batch Scanning function, the scanner is capable of storing up to 100,000 EAN-13 barcode data. It is an ideal cost-saving solution for inventory applications.
Once you scan the “Enter Batch Scanning” command to activate this function, all scanned barcode data will be stored into the memory storage, and the status indicator of scanner will give green blink at regular interval during batch scanning. You can scan and store the barcode data till the memory storage is full. If the storage is full, you will hear 2 long beeps and the status indicator will give 2 red blinks to indicate out of storage. To terminate the batch scanning, please scan the “Exit Batch Scanning” command.
Enter Batch Scanning
Use Quantity Feature
The scanner supports quantity feature when it enters batch scanning. When you use quantity feature, the quanity information and scanned barcode data will be stored into the memory storage together. You can enter the quantity information from 1 to 9999 by scanning the following quantity commands right after you scan the barcode data.
Quantity 0
Quantity 1
Quantity 2
Quantity 7
Quantity 8
Quantity 9
10
There are three ways to output the stored barcode data and quantity information. The preset output format is to transmit stored barcode data as many times as the quantity indicated. But you still can set the scanner to outpt the stored barcode data together with quantity information in two fields, and a prest delimter “,“ will be output in between. To fulfill different application requirements, both the delimiter and output sequency can be changed as well.
As many times as the quantity indicates
◆
<Quantity><Field Delimiter><Scanned Data>
<Scanned Data><Field Delimiter><Quantity>
How to Transmit Stored Data
The scanner is preset to transmit all stored data by scanning the “Transmit
Stored Data” command. During the transmission, the scanner will emit continuous short clicks and the link indicator will blink blue. Then the scanner will give two short beeps after data transmission is completed.
Transmit Stored Data
But you are able to set the scanner to transmit the stored data by placing the scanner onto the cradle as well.
Scan Barcode
Command ◆
Place Scanner onto the Cradle
Scan command or Place
Scanner onto the Cradle
How to Delete Last Scanned Data
If you scanned a wrong barcode, the “Delete Last Scanned Data’’ command is helpful to recover mistake. By scanning the ‘’Delete Last Scanned Data’’ command, the last stored data will be deleted.
Delete Last Scanned Data
11
Link Mode Quick Set
PAIR Mode PICO Mode
UNINSTALL
SPP Master Mode SPP Slave Mode
HID Legacy Mode HID Mode with Passkey
Host Interface Quick Set
(Smart Cradle only)
RS232 Serial
USB HID
Standard Mode ◆
USB HID Turbo Mode
PS/2 (DOS/V)
Keyboard Replacement
USB Com Port
Emulation
Keyboard Layout Quick Set
USA
◆
United Kingdom-UK
PS/2 (DOS/V) KBW
Standard Mode
PS/2 (DOS/V) KBW
Turbo Mode
Latin America
Germany
Canadian French
Japan
Spain
12
System Commands
Information
PowerTool Host Link
Power Off
Operation Mode Quick Set
Clone
Trigger Mode
◆
Option Codes
0 8
4 C
1 9
5 D
2 A
6 E
3 B
7 F
FIN (Finish) END (Exit)
13
Indications
Scanner Indications
Items
Radio connection
Radio disconnection
During connection
Radio connection built
Radio connection lost
Data Transmission
Items
Under charging (on cradle)
Fully charged (on cradle)
Under batch scanning
Pair failure
Out of memory
Battery power low
Battery power extremely low
Good read
Under Configuration
Uninstall state
Upgrade state
Time out warning
Paged by smart cradle
Sleep state / Battery no power
Power Off
Link Indicator
1 blue blink per 2.5 sec.
3 blue blinks per 2 sec.
Quick blue blinks
1 blue blink per 2.5 sec.
3 blue blinks per 2 sec.
Quick blue blink
Status Indicator
Steady red
Steady green
1 green blink per 2.5 sec.
Steady red
2 red blinks
1 red blink at regular interval
8 red blinks
1 green blink
Steady red
Alternative red and green blinks
Steady red
Off
Off
Off
Off
Central Indicator
HB211x Smart Cradle Indications
Side Indicators
Power on
Smart Cradle Upgrade State
Uninstall state
PICO Mode
PAIR Mode
Items
Smart cradle paged by scanner
Central
1 blue blink
Off
Off
Radio Connected Steady blue
Radio Disconnected Off
Radio Connected Steady blue
Radio Disconnected Off
PICO Mode
PAIR Mode
Steady blue
Steady blue
Indicators
Side
Off
Steady red
Alternative red-green blinks
Steady Green
Steady red
Off
Steady red
Steady green
Off
Beeping
Off
Off
Short clicks
4 beeps in ascending tone
4 beeps in descending tone
Short clicks
Beeping
Off
Off
Off
2 Di-do Di-do beeps
2 long beeps
1 beep at regular interval
8 beeps
1 good read beep
Off
Off
Short click
3 long beeps
6 page beeps
Off
Off
Beeping
Power on beeps
Short clicks
Off
Off
Off
Off
Off
6 page beeps
6 page beeps
HB2100 USB Charging Cradle Indication
Power on
Items
Steady blue
Central Indicator
Off
Beeping
14
Advertisement