QUICK INSTALLATION GUIDE OF THE SAGEM F@stTM 3000 (H.323)

QUICK INSTALLATION GUIDE OF THE SAGEM F@stTM 3000 (H.323)
QUICK INSTALLATION GUIDE OF THE SAGEM F@stTM 3000 (H.323)
13 Internet access Configuration
14 Internet access Configuration (cont.)
1 Pack - Unit Presentation
2 Setting-up of the filter and connection
of the ADSL line
Your pack includes the following elements:
•
•
Enter the parameters delivered by your Internet
Access Provider (User Name and Password).
Click Next to continue the configuration.
•
•
Enter the parameters delivered by your Internet
Access Provider or keep the default values (VPI,
VCI, Protocol and encapsulation).
Click Next to continue the configuration.
The SAGEM F@stTM 3000 Residential Gateway
presents in rear panel, the connectors for the
following connections :
•
•
•
•
•
ADSL Line
VoIP telephone line
Mains adapter unit
Ethernet connection
USB connection
•
Connect the ADSL line lead (3) to the LINE
connector of the SAGEM F@stTM 3000.
item 2,
item 3,
item 4,
item 8,
item 9.
On the SAGEM F@stTM 3000, the display LEDs
indicate the active / inactive state of the power supply,
ADSL line, Ethernet, USB and telephone interfaces.
15 Internet access Configuration (cont.)
When the Internet link is up ; the following screen
appears.
•
16 Voice over IP (VoIP) Configuration of
TM
your SAGEM F@st 3000
•
4 Powering up the residential gateway
Click H323 in the VoIP menu ; the following
screen appears.
Click Next to end the Internet Access
Configuration.
•
•
•
3 Connection of the telephone terminal
on VoIP
Connect the second telephone set to the
PHONE connector in using the phone adaptator
(6).
•
Connect the mains adapter unit cable to the
PWR socket on the rear panel of the residential
gateway.
•
Set the On/Off (I/0) switch to On (the «I»
position). The PWR LED comes on.
Click Select then on the
button to enter
the parameters delivered by your Internet
Access Provider (IAP).
Click Save to save the configuration.
4
1
Réf. 251 649 741 éd. 1
5 ADSL Synchronization
6 Lauching CD-ROM
•
Insert the CD-ROM in your computer's
appropriate drive; the following screen appears.
TM
9 Installation and Connection on USB
10 Access to your SAGEM F@st
3000
•
Click USB ; the following screen appears:
When the configuration of your computer (step 1) is
done, you acceed to the step 2.
•
Connect as figure here after (when that asks
you).
In less than two minutes, the Residential Gateway
synchronizes automaticaly with your ADSL line. The
LINE LED is then lit on steady.
•
•
Click Configure your computer (step 1).
7 Interfaces choice
8 Configuring the Ethernet interface
The following screen appears :
•
Click Ethernet then follow the displayed
process.
•
Connect as figure here after (at the right
moment).
•
Go to the item 11 : Configure your SAGEM
F@stTM 3000 (step 2).
11 Access to your SAGEM F@st
(continue)
TM
3000
•
In the "User Name field", enter root and in the
"Password" field, enter 1234.
•
Then click OK to valid.
Remark: If your computer is equipped with an
Ethernet card, we advise you to configure by the
Ethernet port.
Remark: The bar of the screen shows the
equipment's IP address (192.168.30.1).
2
12 Configure your SAGEM F@st
TM
3000
The welcome screen appears.
•
Choose which computer's interface will be used to
connect your SAGEM F@stTM 3000:
•
Ethernet (selection of the network card),
•
USB (drivers' installation).
Click Configure your SAGEM F@stTM 3000.
3
Click the
button or select Quick
Setup from the list on the left of the screen.
17 Voice over IP (VoIP) Configuration
TM
of your SAGEM F@st 3000 (cont.)
•
Enter the following parameters:
Phone No., H323 Id., Codec.
•
Then click the
•
Click the
18 Voice over IP (VoIP) Configuration of
TM
your SAGEM F@st 3000 (cont.)
button.
button.
•
In the scroll down list of the "Interface" field,
select ppp0 (don't take the reboot invit into
account).
•
Check the box of the "Advanced" field.
•
Select the "Enable Fast Start" field.
•
In the "Max Dialled Digits" field, enter the
desirated value.
19 Voice over IP (VoIP) Configuration
TM
of your SAGEM F@st 3000 (cont.)
20 Voice over IP (VoIP) Configuration of
TM
your SAGEM F@st 3000 (cont.)
•
Select the "Use GateKeeper" field.
•
•
Enter the primary address provided by your
Internet Access Provider (IAP).
Select Quick Status from the list on the left of
the screen ; the following screen appears.
•
button to take the
Click the
parameters entered into account.
•
In normal operation, the Internet Access and
VoIP Access status are displayed in green
characters respectively "Internet Access
enabled" and "VoIP enabled".
You can now surf and/or phone on Internet.
The following screen appears.
•
Verify the parameters entered.
•
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising