Setup Poster X6-2-HA

Setup Poster X6-2-HA
Cabling the Interconnect and Storage for Oracle Database Appliance X6-2-HA
1
1
Connect interconnect and
storage to Oracle Database
Appliance X6-2-HA.
Note: The following cables are included as part of the
Oracle Database Appliance shipment.
2
3 5
Node 1
Node 1
Node 0
Node 0
Storage
Shelf
Storage
Shelf
4 6
Storage
Expansion
Shelf
Network
Purpose
Start - Compute Node 0
End - Compute Node 1
1. Connect green InfiniBand cable
Connect into green port (PORT2) in
PCIe slot 1
Connect into green port (PORT2) in
PCIe slot 1
2. Connect yellow InfiniBand cable
Connect into yellow port (PORT1) in
PCIe slot 1
Connect into yellow port (PORT1) in
PCIe slot 1
Storage Shelf
Connect optional storage
expansion shelf to Oracle
Database Appliance X6-2-HA.
7 9
Note: The following cables are included as part of the
Oracle Database Appliance shipment.
8 10
Storage Expansion Shelf
Purpose
Start - Compute Node
End - Storage Shelf
Purpose
Start - Compute Node
End - Storage Expansion Shelf
3. Connect dark blue SAS cable
Connect into dark blue port
(SAS0) in PCIe slot 2 in Node 0
Connect into dark blue port in
top IO Module (PORT 0)
7. Connect dark blue SAS cable
Connect into dark blue port
(SAS0) in PCIe slot 2 in Node 1
Connect into dark blue port in
top IO Module (PORT 0)
4. Connect light blue SAS cable
Connect into light blue port
(SAS1) in PCIe slot 3 in Node 0
Connect into light blue port in
bottom IO Module (PORT 0)
8. Connect light blue SAS cable
Connect into light blue port
(SAS1) in PCIe slot 3 in Node 1
Connect into light blue port in
bottom IO Module (PORT 0)
5. Connect dark red SAS cable
Connect into dark red port
(SAS1) in PCIe slot 2 in Node 1
Connect into dark red port in
top IO Module (PORT 1)
9. Connect dark red SAS cable
Connect into dark red port
(SAS1) in PCIe slot 2 in Node 0
Connect into dark red port in
top IO Module (PORT 1)
6. Connect light red SAS cable
Connect into light red port
(SAS0) in PCIe slot 3 in Node 1
Connect into light red port in
bottom IO Module (PORT 1)
10. Connect light red SAS cable
Connect into light red port
(SAS0) in PCIe slot 3 in Node 0
Connect into light red port in
bottom IO Module (PORT 1)
Note: The network cabling diagram on this page supports 10GBase-T (copper) public networking and uses InfiniBand for the interconnect between the two servers.
Support for 10GbE SFP+ (fiber) public networking is optional by ordering an Oracle Database Appliance X6-2-HA with 10GbE SFP+ PCIe cards instead of
InfiniBand PCIe cards. If you purchased an Oracle Database Appliance X6-2-HA with 10GbE SFP+ PCIe cards, see the documentation for
network cabling instructions.
E76904-01; CMTBK Mfg no 7315500
1
You can also scan the Quick Response
Code with your mobile device to read
the documentation.
Preparing to Deploy Oracle Database Appliance X6-2-HA
1
Set Up the Hardware and Register with
My Oracle Support
A
B
C
2
Ensure that the system hardware is set up and mounted
properly as specified in the instructions in the
Oracle Database Appliance Owner’s Guide, found on:
http://www.oracle.com/goto/oda/docs
Planning the Network Configuration
A
E
Add the hardware SI and new software licenses that you
received with Oracle Database Appliance to your My Oracle
Support profile. Each SI registration may take up to 24 hours.
Plan the Software and Database
Configuration Choices
A
B
Plan your software installation choices as follows:
• Configuration type: Custom
• System name (for example, hrsys)
• Region (for example, America)
• Time zone (for example, America/Los_Angeles)
• Deployment type (for example, Oracle Real Application Clusters)
• Disk group redundancy: High (triple-mirrored) or Normal
(double-mirrored)
• Database backup (for example, External). Local appliance
internal backups utilize 60% of available disk space for
archive logs and backup, external backups utilize 20%
of available disk space for archive logs.
Prepare to enter information for the following fields:
• Database Name (for example, hrdb)
• DB Class (for example, odb-02)
• Database Language (for example, English)
• Database Block Size (for example, 8192)
• Database Character Set (for example, AL32UTF8)
• Database Territory (for example, America)
• Node 1 network information
° Single Client Access Name (SCAN) and two
addresses (for example, hrsys-scan and
192.0.2.16, 192.0.2.17)
° Public name and address (for example, hrsys1 and
192.0.2.20)
° VIP name and address (for example, hrsys1-vip and
192.0.2.21)
° Netmask for public network (for example,
255.255.252.0)
° Gateway for public network (for example,
192.0.2.1)
Plan for Oracle Auto Service Request and
Oracle Cloud File System Size
A
B
C
(Optional) To configure Oracle Auto Service Request
(Oracle ASR) be prepared to provide the following:
• Proxy server name to use for your deployment
• Proxy server port
• Proxy username
• Proxy password
• Oracle online account username
• Oracle online account password
(Optional) Configure External Oracle ASR Manager
• Oracle ASR Manager IP/host name
• Oracle ASR Manager port
• Your My Oracle Support account user name and password
For more information about Oracle ASR, see:
www.oracle.com/technetwork/systems/asr/overview/index.html
To change the default name and size of Oracle Cloud
File System, be prepared to provide the following:
• Name of file system (default name is /cloudfs)
• Size of file system (default size is 50 GB)
Collect the following information for your Oracle ILOM network:
° VIP name and address (for example, hrsys0-vip and
192.0.2.19)
• Cluster network information
Set Up Oracle ILOM Configuration
(Optional)
Configure Oracle Integrated Lights Out Manager (Oracle ILOM)
for managing Oracle Database Appliance independently of the
operating system.
Collect the following cluster node information from your
network administrator:
° Public name and address (for example, hrsys0 and
192.0.2.18)
° (Optional) Network Time Protocol server addresses
6
4
• Node 0 network information
° Domain name server addresses
Note: You cannot obtain software or support from Oracle without
registered hardware and software SIs.
5
B
° Domain name (for example, example.com)
Oracle Database Appliance includes the network cables for the
interconnect between the two servers. Public network cables
are not included in Oracle Database Appliance shipments.
Obtain your hardware Support Identifier (SI) from your
hardware vendor.
Collect the following network and cluster information from
your network administrator:
Planning the Network Configuration,
Continued
• Generic network information
Verify that your shipment contains the correct power
cables for your location.
D
3
•
Oracle ILOM name and address for Node 0 (for example,
hrsysilom1 and 10.0.0.3)
•
Oracle ILOM name and address for Node 1 (for example,
hrsysilom2 and 10.0.0.4)
•
Netmask for management network (for example,
255.255.255.0)
•
Gateway for management network (for example, 10.0.0.1)
Note: Public, VIP, and SCAN IP addresses must be on the same subnet.
Note: For Oracle Database Appliance Virtualized Platform, your network
administrator must provide extra IP addresses for dom0, ODA_BASE,
and the virtual machines.
7
Download the Software
A
Review Oracle Database Appliance
Information
(Recommended) Download Oracle Appliance Manager Configurator:
http://www.oracle.com/technetwork/database/
database-appliance/overview/index.html
•
Review the most recent version of this poster in the Oracle
Database Appliance online documentation library:
http://www.oracle.com/goto/oda/docs
(i) Run the configurator, preferably on a computer that is on
a network that is local to where you plan to install Oracle
Database Appliance.
•
Review the Oracle Database Appliance information and online
demos on Oracle Technology Network:
http://www.oracle.com/technetwork/database/
database-appliance/overview/index.html
•
Review the Oracle Database Appliance Information Center,
which is contained in My Oracle Support Note 1417713.2:
support.oracle.com/CSP/main/
article?cmd=show&type=NOT&id=1417713.2
•
Review the latest information about Oracle software
and hardware products:
www.oracle.com
(ii) Enter and validate your configuration choices with the
configurator. This creates a configuration file that you
can use during actual deployment. You can also run
Oracle Appliance Manager Configurator directly from
Oracle Database Appliance during deployment.
B
8
Follow the instructions in My Oracle Support Note 888888.1:
support.oracle.com/CSP/main/
article?cmd=show&type=NOT&id=888888.1
(i) Download the latest software (Oracle Database Appliance
End-User Bundle) to a local computer on the network.
(ii) Download the latest Oracle Database Appliance
patch bundle, which you must apply before or after
deployment, and review the README files.
Note: For information about the configuration options such as
Deployment Type, Database Class, or any of the other options,
refer to Oracle Appliance Manager Configurator online help.
E76904-01; CMTBK Mfg no 7315500
2
You can also scan the Quick Response
Code with your mobile device to read
the documentation.
Oracle Database Appliance X6-2-HA Bare Metal Setup
1
1
1
1
2
3
1
2
Node 1
Node 0
Storage
Shelf
Start Up the Systems
3
4
Turn on power to the storage
shelf and optional storage
expansion shelf.
Configure the Network
Configuring the network enables you to use scp to copy files
to Oracle Database Appliance. Consult with your network
administrator to obtain the information that you need to
complete the initial configuration.
To ensure that the storage cabling is properly configured, log into
the console as root with the password welcome1 and run the
following oakcli validate command:
Connect power to the
power supply.
A
Validate Storage
/opt/oracle/oak/bin/oakcli validate -c storagetopology
A
Log in to the console as root with the password
welcome1.
Configure the network using the command:
B
On each node, after the green
SP OK LED (4) is steady ON,
push the power button (5).
B
C
Wait for the green Power
OK LED (6) to turn steady ON.
The Power OK LED
might blink for several
minutes. Do not repeatedly
push the power buttons.
C
Select the Global option and then enter the domain name,
DNS servers, host names, network interface, IP addresses for
nodes, netmask, and gateway when prompted.
D
Type vncserver to start vnc server.
/opt/oracle/oak/bin/oakcli configure firstnet
Connect the Power and Public Network Cables
Important: Follow the instructions on Page 1 to cable the server nodes, storage system(s) and
interconnect before proceeding. On both nodes, connect:
A Power to the power supply unit (PSU) (1)
B
(Optional) Ethernet to network management for Oracle Integrated Lights Out Manager (Oracle ILOM) (2)
C
(Optional) On Node 0 only, connect keyboard and mouse to USB and video display to VIDEO (3)
5
Download Oracle Database Appliance
End-User Bundle
A
B
From a browser on an external client, log on to My Oracle
Support. Identify the latest software version by reading the
following note:
https://support.oracle.com/CSP/main/
article?cmd=show&type=NOT&id=888888.1
To determine if your Oracle Appliance Manager software
version is current, run the following command:
/opt/oracle/oak/bin/oakcli show version -detail
If your version is out of date, then update your base
image as described in the following note:
https://support.oracle.com/CSP/main/article?
cmd=show&type=NOT&id=888888.1
C
Download the End-User Bundle zip file from this URL:
https://updates.oracle.com/download/12978712.html
D
Use scp to copy the Oracle Database Appliance End-User
Bundle to a location on Node 0 (for example, to /tmp).
E
(Optional) Copy the configuration file created by Oracle
Appliance Manager Configurator to a location on Node 0
(for example, to /tmp).
6
6
5
Unpack Oracle Database Appliance
End-User Bundle
Use the oakcli unpack –package command. For example,
at the [[email protected]]# prompt, type:
/opt/oracle/oak/bin/oakcli unpack -package
/tmp/p12978712_xxxxx_Linux-x86-64.zip
4
7
Deploy the Oracle Software
A Connect to Node 0 using VNC with the hostname for Node 0
and Port as 5901
B
Typical and Custom Installations
(Optional) Configure NTP servers (the default is Cluster
Time Synchronization Service)
•
(Optional) Configure and set up Oracle ILOM
•
(Optional) Specify additional network interfaces
(two additional bonded 10 GB interfaces, one
additional 10 GB interface)
•
(Optional) Configure Oracle Auto Service Request
•
(Optional) Resize the /cloudfs file system (the default
is 50 GB)
Complete Oracle Database
Appliance Deployment
Click Install to begin deployment when the configuration
information is complete.
Enter the following command:
[[email protected]]# /opt/oracle/oak/bin/oakcli deploy
• The Oracle Appliance Manager Welcome screen opens.
The Configuration Type window enables you to select a Typical
or a Custom Configuration. Selecting Custom enables you to:
•
8
• (Optional) If you saved a configuration file using the
Oracle Appliance Manager Configurator, then
click Browse to load the file.
• Click Next.
C
The Configuration Type screen opens. Make your selection
for each configuration and click Next.
D
Enter the requested information as each subsequent
screen appears.
The deployment takes about 1 hour to finish.
E76904-01; CMTBK Mfg no 7315501
3
You can also scan the Quick Response
Code with your mobile device to read
the documentation.
Oracle Database Appliance X6-2-HA Virtualized Platform Setup
1
1
1
1
2
3
1
2
Node 1
Node 0
Start Up the Systems
Connect power to the
power supply.
A
B
Storage
Shelf
3
C
Verify Virtual Machine Image
Check that Oracle Virtual Machine Image is installed.
Turn on power to the storage
shelf and optional storage
expansion shelf.
On each node, after the green
SP OK LED (4) is steady ON,
push the power button (5).
A
Log in to dom0 as root with the password welcome1.
B
Confirm that you have Oracle Virtual Machine image for
Oracle Database Appliance installed by running the
following oakcli show env_hw command:
A Power to the power supply unit (PSU) (1)
C
Wait for the green Power
OK LED (6) to turn steady ON.
The Power OK LED
might blink for several
minutes. Do not repeatedly
push the power button.
B (Optional) Ethernet to network management for Oracle Integrated Lights Out Manager (Oracle ILOM) (2)
6
5
Configure the Network
Configuring the network enables you to use scp to copy files
to Oracle Database Appliance. Consult with your network
administrator to obtain the information that you need to
complete the initial configuration.
A
Log in to dom0 as root with the password welcome1.
B
Configure the network using the command:
/opt/oracle/oak/bin/oakcli show env_hw
/opt/oracle/oak/bin/oakcli configure firstnet
If the resulting output does not include the string VM-Dom0
or the command fails with any other error, then you need to
install the Oracle Database Appliance Virtualized Platform
image.
C
Select the Global option and then enter the domain name,
DNS servers, host names, network interface, IP addresses for
nodes, netmask, and gateway when prompted.
Note: To install the Oracle Database Appliance Virtual Platform image
follow the instructions in My Oracle Support Note 1520579.1
https://support.oracle.com/CSP/main/
article?cmd=show&type=NOT&id=1520579.1
Connect the Power and Public Network Cables
Important: Follow the instructions on Page 1 to cable the server nodes, storage system(s) and
interconnect before proceeding. On both nodes, connect:
4
4
C (Optional) On Node 0 only, connect keyboard and mouse to USB and video display to VIDEO (3)
5
Deploy ODA_BASE and Validate Storage
6
Deploy the Oracle Software
on ODA_BASE
From a browser on an external client, log on to My Oracle Support.
Identify the latest software version by reading the following note:
https://support.oracle.com/CSP/main/
article?cmd=show&type=NOT&id=888888.1
A
Configure the ODA_BASE network using the command:
/opt/oracle/oak/bin/oakcli configure firstnet
B
Download the ODA_BASE template from this URL:
https://updates.oracle.com/download/16186172.html
and copy the template to the /OVS directory on dom0
Select the Global option and then enter the domain name, DNS
servers, host names, network interface, IP addresses for nodes,
netmask, and gateway when prompted.
C
C
Deploy ODA_BASE using the command:
/opt/oracle/oak/bin/oakcli deploy oda_base
Start VNC server in ODA_BASE by entering the following
command: vncserver :1
D
D
When prompted for Location, enter the full path name
for the ODA_BASE template that you downloaded and
copied, for example
/OVS/templateBuild-2014-04-19-02-33.tar.gz
Use a VNC client to connect to the ODA_BASE IP address
(from Step A) and port 5901
E
Enter the following command: /opt/oracle/oak/bin/oakcli deploy
F
The Oracle Appliance Manager Welcome window opens.
A
B
E
Select the number of cores and amount of memory
allocated to ODA_BASE.
F
To ensure that the storage cabling is properly configured,
connect to ODA_BASE using VNC with Dom0 for
the hostname and 5900 for the Port. Log in as root
with the password welcome1 and run the following
oakcli validate command:
/opt/oracle/oak/bin/oakcli validate -c storagetopology
7
Deploy the Oracle Software on
ODA_BASE, Continued
G
Click Next.
H
The Configuration Type window opens. Make your selection
for each configuration option and click Next.
I
Enter the requested information on the remaining windows.
8
Complete Oracle Database
Appliance Deployment
Click Install to begin deployment when the configuration
information is complete.
Note: Select Custom to configure options that have default values
in Typical configurations, such as:
• Normal disk redundancy
• NTP servers
• Oracle ILOM
• Additional network interfaces
• Oracle Auto Service Requests (Oracle ASR)
• Size of the /cloudfs file system (default is 50 GB)
The deployment takes about 1 hour to finish.
For more information about Oracle Database Appliance, go to Oracle Technology Network: oracle.com/technetwork/server-storage/engineered-systems/database-appliance/index.html
For more information about deployment, go to: http://www.oracle.com/goto/oda/docs You can also scan the Quick Response Code with your mobile device to read the documentation.
Copyright © 2016, Oracle and/or its affiliates. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. E76904-01; CMTBK Mfg no 7315501
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement