660-1120-0000-E 1120RF-3000,4000-BW
 Users guide
TH1120RF-3000 (3000 w)
TH1120RF-4000 (4000 w)
Web programmable thermostat
The installation of this thermostat should be made by a certified
electrician and must be installed in conformity with the national
and local Electrical Codes.
Since you are a valuable customer, before starting
the installation of your new thermostat, please
make sure that the breakers for your heating system
are offatthe main electrical panel!
The thermostat must be installed in
series with your heating device.
Connecting the thermostat directly
to the line voltage source will
damage the unit.
Note: The wires of this thermostat are non-polarized.
Technical Specifications
Operating voltage: 120/208/240 Vac, 60 Hz
TH1120RF-3000 thermostat
Maximum load:
12.5 A / 3000 W @ 240 Vac
Resistive load only
Minimum load:
0.5 A / 120 W @ 240 Vac
TH1120RF-4000 thermostat
Maximum load:
16.7 A/ 4000 W @ 240 Vac
Resistive load only
Minimum load:
0.5 A / 120 W @ 240 Vac
Setpoint range: 5 °C to 30 °C (41 °F to 86 °F)
Display range: 0 °C to 70 °C (32 °F to 99 °F)
Resolution: + 0.5 °C (+ 1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Compatible with an electric heating system such as:
о Baseboard heater
+ Convector (short cycle)
« Fan-forced convector (long cycle)
Install your thermostat Mn
Remove your old
thermostat. It should be
connected on 2 wires. If
you have more than 2
wires, refer to our website
Power up the
Note: For a fan-forced
convector, go to the
"Advanced Settings” section
to change the control cycle
of the thermostat.
Replace the
cover and lock.
Unlock and lift
the thermostat cover.
Use the provided connectors to
connect the two wires of the
thermostat to the wires previously
connected to your old thermostat.
Use the two screws to
©) secure the thermostat
to the electrical box.
Make sure to firmly tighten the wire connectors for a secure
connection. A loose connection can be a fire hazard.
Special CO/ALR solderless connectors must be used when
connecting with aluminum conductors.
Link your thermostat to your Web interface
Initiate the connectivity
session by pressing the eN
button on the GT125.
*Do not hold the button down.
Wait until the light flashes
green, indicating that new
devices can be added to
your network.
[] Stay connected Sign in
Link your network
to neviweb*
Forgot your password?
New to neviweb?
To link your wireless
network to neviweb”,
go to neviweb.com
and refer to your
GT125 Web interface
user's guide.
NEVI web®
For more information, visit our website at:
On the thermostat
Connect to your network, the display:
wireless thermostat that is
closest to the GT125 by +
pressing simultaneously е\ -
the 1 and J button. Flashes = Connecting
@ Remains lit= Connected
If the connectivity fails,
an error message will
appear on the display.
Refer to our website to
troubleshoot the unit.
Connect all your wireless thermostats
the same way, by going to the next
closest thermostat.
When all the
thermostats are
connected, press Ee
again on the SN Ju En Fr
button of the GT125 to
close the connectivity
Advanced Settings
All of the thermostat's settings can be set through the Web.
However, if you have not created your wireless network and
need to change the control cycle, you must:
Get the setpoint to its minimum
and hold the {, button for 3
seconds to access the menu.
Press the À button to change the setting.
Press the Y button to select the next parameter.
Press and hold the J button for 3 seconds to exit the
menu and return to normal display.
Parameter & Setting
Default Display
1 Control Cycle CH PT
SHRT (short cycle for electric baseboard) I
FAN (long cycle for fan forced heater) Cycle
Transmitter Module IC: 7693A-B89XAM9A / FCC ID: OA3MRES9XAMOA
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
ofthe device.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
+ Connectthe equipment into an outlet on a circuit different from
thatto which the receiver is connected.
+ Consultthe dealer or an experienced radio/TV technician for
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their
products against defects in material and workmanship for a 3 year
period from the date of purchase, under normal use and service, when
proof of purchase of such is provided to the manufacturer. This
warranty does not cover any transportation costs that may be incurred
by the consumer. Nor does it cover a product subjected to misuse or
accidental damage. The obligation of Sinopé Technologies Inc., under
the terms of this warranty, will be to supply a new unit and this releases
the manufacturer from paying the installation costs or other secondary
charges linked to replacing the unit orthe components.
For more information, visit our website at:
660-1120-0000-E J
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF