614-03110-00 SR-S_SR-D_SL

SR-S\ SR-D\ SL-PM
Quick Instruction of WiFi Connection
Table of Contents
SR-S Quick Instruction of WiFi Connection ............................................................................................................... 02
SR-D Quick Instruction of WiFi Connection ............................................................................................................... 06
SL-PM Quick Instruction of WiFi Connection ............................................................................................................. 10
SolarRiver-S
SolarRiver-D
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
1
SolarLake-PM
SR-S Quick Instruction of WiFi Connection
The Procedure of WiFi Setting
Step 1: Write down the WiFi SSID of inverter.
When the inverter is running, press the function
button until the WiFi SN is displaying on the
screen.
Step 2: Configure and set parameter of WiFi
module.
WLAN Configuration
Available Router
Refresh
Router 1
1. Choose the WiFi SSID:
samilpower_10829A
2. Input the default password “samil123”
3. Input the website: http://11.11.11.1
4. Choose router
Router 2
Router 3
Router 4
WLAN
Prepare a laptop with WiFi. Open the wireless
network connection.
Advanced
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
2
BUFFALO-5D8958
Input Router password and click OK.
Back
KEY
●●●●●●●●
Unmask KEY
OK
WLAN Configuration
Available Router
Refresh
Router 1
Router 2
Router 3
Router 4
WLAN
Advanced
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
3
Wait 15 seconds and then repeat 1 to 3. if
connection is established, you can see a tick on
the right rooter.
You can also change the module password.
Choose ‘Advanced’ you can see the following
screen.
Advanced Options
WLAN Network Setting
Device Parameter Setting
Firmware Upgrade
WLAN
Advanced
Advanced Options
Choose Device Parameter Setting and change
your password:
Back
Device Name
Device Parameter Setting
SAMILPOWER 10829A
Password
samil123
OK
WLAN
Advanced
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
4
Advanced Options
Router Name
In WLAN Network Setting, you can connect to
router manually.
WLAN Setting
Channel
AUTO
Security
AUTO
Key
Unmask KEY
WLAN
Advanced
Reset and factory setting:
Screen 1 →
Hold pressing the function key at screen 1 for
15 seconds.
When you see the screen 2, the WiFi setting will
be reset to factory setting.
Screen 2 →
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
5
SR-D Quick Instruction of WiFi Connection
The Procedure of WiFi Setting
Ethernet
2012-03-03 10:22:23
Auto-IP/DHCP
Step 1: Ethernet connection established before
opening “SolarPower Browser”.
Refer to settings when using router:Main
Menu->Settings->Network->Ethernet. In
"Ethernet" interface move the cursor to
"Manual-IP", press "OK" twice(one press to
confirm). Then it will enter "Manual-IP" interface.
Manual-IP
Ethernet
Current mode:
2012-03-03 10:22:23
Auto-IP/DHCP
Manual-IP
Manual-IP
Current mode:
Press OK to confirm
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
Confirm?
6
Manual-IP
Manual-IP
Press "right" or "left" key to move the cursor to
select the figure which need to be modified.
Press "up" or "down" key to modify figure(IP
Address:192.168.000.002. Subnet Mask:
255.255.255.000, others are 0). Press “OK”
after modifying. LCD will display the setting
parameter and press “OK” again, now setting is
over. LCD interface will reboot and then enter
to home interface automatically.
2012-03-03 10 : 26 : 05
IP:
192.168.000.002
SubnetMask:
255.255.255.000
Gateway:
000.000.000.000
DNS:
000.000.000.000
Parameter set for PC:
Set IP address as 192.168.000.001,
Set Subnet mask as 255.255.255.000.
Open SolarPower Browser:
Left/Right : Move Selection
Up/Down : Increase/Decrease value
Press OK to confirm
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
7
Step 2: Write down the information of router.
Double-click name of inverter then enter detail
information interface. Set the SSID of router
which WIFI is going to be connected to and
input the Router password. Then save these
information.
Network
2012-03-03 10:27:23
Step 3: Reboot the LCD interface automatically
and disconnect wire connection.
Step 4: Check WIFI information:
Ethernet
Enter the interface: Main Menu -> Settings ->
Network, move the cursor to "WIFI" and press
"OK".
WIFI
Press OK to confirm
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
8
Wifi
2012-03-03 10 : 28 : 10
If WIFI has not been set, shown as following
figure.
2012-03-03 10 : 28 : 50
If WIFI has been set, shown as following figure.
Link Name:
Press ESC to Back
Wifi
Link Name:
BAFFAL0-5D8959
Press ESC to Back
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
9
SL-PM Quick Instruction of WiFi Connection
The Procedure of WiFi Setting
Step 1: Write down the WiFi SSID of inverter.
Ethernet
WIFI Message
2012-03-03 10:22:23
2014-06-04 13:12:55
Auto-IP/DHCP
Reset module
Manual-IP
Default
module
SSID:mode:
Current
AP_IP:
SAMILPOWER_10829A
Manual-IP
11.11.11.1
Press ESC to return
Press OK to confirm
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
10
You can see the SSID by: Main Menu ->
Settings -> Network -> WiFi Message
WLAN Configuration
Available Router
Step 2: Configure and set parameter of WiFi
module.
Refresh
Router 1
Prepare a laptop with WiFi. Open the wireless
network connection.
1. Choose the WiFi SSID:
samilpower_10829A
2. Input the default password “samil123”
3. Input the website: http://11.11.11.1
4. Choose router
Router 2
Router 3
Router 4
WLAN
Advanced
BUFFALO-5D8958
Input Router password and click OK.
Back
KEY
●●●●●●●●
Unmask KEY
OK
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
11
WLAN Configuration
Available Router
Refresh
Wait 15 seconds and then repeat 1 to 3. if
connection is established, you can see a tick on
the right rooter.
Router 1
Router 2
Router 3
Router 4
WLAN
Advanced
You can also change the module password.
Choose ‘Advanced’ you can see the following
screen.
Advanced Options
WLAN Network Setting
Device Parameter Setting
Firmware Upgrade
WLAN
Advanced
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
12
Advanced Options
Choose Device Parameter Setting and change
your password:
Back
Device Parameter Setting
Device Name
SAMILPOWER 10829A
Password
samil123
OK
WLAN
Advanced
Advanced Options
Router Name
In WLAN Network Setting, you can connect to
router manually.
WLAN Setting
Channel
AUTO
Security
AUTO
Key
Unmask KEY
WLAN
Advanced
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
13
WIFI Message
2014-06-04 13:12:55
Reset module
Default module
SSID:
AP_IP:
SAMILPOWER_10829A
11.11.11.1
Press ESC to return
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
14
Factory setting:
Choose ‘Default module’ on the screen, the
WiFi setting will be reset to factory setting.
SR-S\ SR-D\ SL-PM_WIFI_IG_V1.0_EN
Download PDF