HP 5800 Switch Series data sheet

Data sheet
HPE 5800 Switch Series
Key features
•For enterprise edge, distribution, data center
•Cut-through design with low latency
•Support for up to 84 ports
•OAA module for flexible deployment
•Redundant, hot-swappable power supplies, fans
Product overview
HPE 5800 Switch Series offer an unmatched combination of Gigabit and 10 Gigabit Ethernet
port density, high-availability architecture, and full Layer 2 and Layer 3 dual-stack IPv4 and
IPv6 capabilities. In addition to wire-speed line-rate performance on all ports, the switches
include patented Intelligent Resilient Framework (IRF) technology and Rapid Ring Protection
Protocol (RRPP), which allow local or geographically distributed HPE 5800 switches to be
interconnected for higher resiliency and performance. Available in PoE and non-PoE models
as well as 1 RU and 2 RU form-factor configurations, HPE 5800 Switch Series are built on open
standards and include an open application architecture (OAA) module slot that enables flexible
deployment options for new services. These versatile switches are ideal for use in the network
core of buildings or departments, or as high-performance switches in the convergence layer
or network edge of enterprise campus networks.
Data sheet
Page 2
Features and benefits
Quality of service (QoS)
•Powerful QoS feature
Creates traffic classes based on access control lists (ACLs), IEEE 802.1p precedence, IP, and
DSCP or Type of Service (ToS) precedence; supports filter, redirect, mirror, or remark; supports
the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR),
weighted fair queuing (WFQ), weighted random early discard (WRED), weighted deficit round
robin (WDRR), and SP+WDRR
•Integrated network services
With support for open application architecture (OAA) modules, extends and integrates
application capability into the network
•Ring Resiliency Protection Protocol (RRPP)
Provides fast recovery for ring Ethernet-based topology; provides consistent application
performance for applications such as VoIP
Management
•Remote configuration and management
Enables configuration and management through a secure Web browser or a CLI located on a
remote device
•IEEE 802.1AB LLDP discovery
Advertises and receives management information from adjacent devices on a network,
facilitating easy mapping by network management applications
•USB support
––File copy
Allows users to copy switch files to and from a USB Flash drive
•DHCP options
––DNS Relay and SMTP Redirection
––DHCP Server (RFC 2131), Client, and Option-82 Relay (RFC 3046)
•sFlow®
Provides scalable, ASIC-based network monitoring and accounting, which allows network
operators to gather a variety of sophisticated network statistics and information for capacity
planning and real-time network monitoring purposes
•SNMPv1, v2c, and v3
Facilitate centralized discovery, monitoring, and secure management of networking devices
•Network Time Protocol (NTP)
Synchronizes timekeeping among distributed time servers and clients; keeps timekeeping
consistent among all clock-dependent devices within the network so that the devices can
provide diverse applications based on the consistent time
Connectivity
•High-density port connectivity
Supports up to 84 1-Gigabit ports per unit (612 per stack)
•Auto-MDIX
Automatically adjusts for straight-through or crossover cables on all 10/100 ports
Data sheet
Page 3
•Jumbo frames
On Gigabit Ethernet and 10 Gigabit ports, jumbo frames of 9k size allow high-performance
remote backup and disaster-recovery services
•IEEE 802.3af Power over Ethernet (PoE)
Provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as
IP phones, wireless access points, and security cameras
•IEEE 802.3at Power over Ethernet (PoE+) support
Simplifies deployment and dramatically reduces installation costs by helping to eliminate the
time and cost involved in supplying local power at each access point location
•IPv6 native support
––IPv6 host
Enables switches to be managed and deployed at the IPv6 network’s edge
––Dual stack (IPv4/IPv6)
Transitions from IPv4 to IPv6, supporting connectivity for both protocols
––MLD Snooping
Forwards IPv6 multicast traffic to the appropriate interface
––IPv6 ACL/QoS
Supports ACL and QoS for IPv6 network traffic, preventing traffic flooding
––IPv6 routing
Supports IPv6 static routes and IPv6 versions of RIP, OSPF, IS-IS, and BGP routing protocols
Performance
•Hardware-based wire-speed access control lists (ACLs)
Help provide high levels of security and ease of administration without impacting network
performance with a feature-rich TCAM-based ACL implementation
•Unique versatile architecture
Supports the best of both fixed-port and modular configurations
Resiliency and high availability
•Data center—optimized design
––HPE 5800AF-48G Switch (JG225A) supports
Front-to-back and back-to-front airflow for hot or cold aisles, rear rack mounts, and redundant
hot-swappable AC or DC power and fans
Manageability
•Full-featured console
Provides complete control of the switch with a familiar CLI
•Web interface
Allows configuration of the switch from any Web browser on the network
•RMON and sFlow
Provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
•Multiple configuration files
Allow multiple configuration files to be stored to a flash image
Data sheet
Page 4
•Troubleshooting
––Ingress and egress port monitoring
Enable network problem solving
––Traceroute and ping
Enable testing of network connectivity
––Virtual cable tests
Provide visibility to cable problems
Layer 2 switching
•GARP VLAN Registration Protocol
Allows automatic learning and dynamic assignment of VLANs
•32k MAC addresses
Provide access to many Layer 2 devices
•4,094 port-based VLANs
Provide security between workgroups
•IEEE 802.1ad QinQ and selective QinQ
Increase the scalability of an Ethernet network by providing a hierarchical structure; connect
multiple LANs on a high-speed campus or metro network
•Gigabit Ethernet port aggregation
Allows grouping of ports to increase overall data throughput to a remote device
•10GbE port aggregation
Allows grouping of ports to increase overall data throughput to a remote device
•IPFIX/sFlow
Allows traffic sampling
•Spanning Tree Protocols (STP, MSTP, and RSTP) and STP root guard
Helps prevent network loops; up to 32 MSTP instances available
Layer 3 services
•Address Resolution Protocol (ARP)
Determines the MAC address of another IP host in the same subnet; supports static ARPs;
gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP
operation between subnets or when subnets are separated by a Layer 2 network
•Dynamic Host Configuration Protocol (DHCP)
Simplifies the management of large IP networks and supports client and server; DHCP Relay
enables DHCP operation across subnets
Layer 3 routing
•Layer 3 IPv4 routing
Provides routing of IPv4 at media speed; supports static routes, RIP and RIPv2, OSPF, IS-IS, and BGP
•RIP and RIPng support
Provides complete support of RIP for both IPv4 and IPv6
•OSPF and OSPFv3 support
Provides complete support of OSPF for both IPv4 and IPv6
Data sheet
Page 5
•IS-IS and IS-ISv6 support
Provides complete support of IS-IS for both IPv4 and IPv6
•Layer 3 IPv6 routing
Provides routing of IPv6 at media speed; supports static routes, RIPng, OSPFv3, IS-ISv6, and BGP4+
•Bidirectional Forwarding Detection (BFD)
Enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP,
IS-IS, VRRP, MPLS, and IRF
•Virtual Router Redundancy Protocol (VRRP) and VRRP Extended
Allow quick failover of router ports
•Policy-based routing
Makes routing decisions based on policies set by the network administrator
•IGMPv1, v2, and v3
Allow individual hosts to be registered on a particular VLAN
•PIM-SSM, PIM-DM, and PIM-SM (for IPv4 and IPv6)
Support IP multicast address management and inhibition of DoS attacks
•Equal-Cost Multipath (ECMP)
Enables multiple equal-cost links in a routing environment to increase link redundancy and
scale bandwidth
•MPLS support
Provides extended support of MPLS, including MPLS VPNs and MPLS Traffic Engineering
(MPLS TE)
•VPLS support
Provides extended support of VPLS for data center to data center communication at Layer 2;
provides support of hierarchical VPLS for scalability
Security
•Unicast Reverse Path Forwarding (URPF)
Allows normal packets to be forwarded correctly, but discards the attaching packet due to lack
of reverse path route or incorrect inbound interface; prevents source spoofing and distributed
attacks; supports distributed URPF
•Defense-in-depth security
Provides integrated and distributed security enforcement that can be managed from a central
location, such as the HPE Intelligent Management Center (IMC)
•Advanced processor queuing mechanism
Helps prevent denial-of-service (DoS) attacks, while DHCP Snooping helps facilitate that devices
can only receive an IP address from a legitimate DHCP Server on the network
•IEEE 802.1X-based dynamic delivery of QoS, ACLs, and VLANs
Allows complete control over user network access
•Guest VLAN
Provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X
•Port isolation
Secures and adds privacy, and prevents malicious attackers from obtaining user information
Data sheet
Page 6
•MAC-based authentication
Allows or denies access to the switch based on a client MAC address
•HTTPS management
Provides secure Web management
•Multi-Customer Edge (MCE)—Multicast Virtual Routing and Forwarding (MVRF)
Provide MPLS Edge router support
•Public Key Infrastructure (PKI)
Is used to control access
•RADIUS/HWTACACS
Eases switch management security administration by using a password authentication server
•Secure Shell (SSHv2)
Encrypts all transmitted data for secure, remote CLI access over IP networks
•IP source guard
Helps prevent IP spoofing attacks; filters packets on a per-port basis, which prevents illegal
packets from being forwarded
•Access control lists (ACLs)
Helps provide high levels of security and ease of administration; 6k ingress entries and 1k egress
entries (IPv4 and IPv6)
Convergence
•Voice VLAN
Automatically assigns VLAN and priority for IP phones, simplifying network configuration,
and maintenance
•Internet Group Management Protocol (IGMP)
Utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast
networks; supports IGMPv1, v2, and v3
•Protocol Independent Multicast (PIM)
Defines modes of Internet multicasting to allow one-to-many and many-to-many transmission of
information; supports PIM Dense Mode (DM), Sparse Mode (SM), and Source-Specific Mode (SSM)
•LLDP-MED (Media Endpoint Discovery)
Defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN
to automatically configure network devices such as IP phones
Monitor and diagnostics
•Port mirroring
Enables traffic on a port to be simultaneously sent to a network analyzer for monitoring
•OAM (IEEE 802.3ah)
Operations, administration, and maintenance (OAM) management capability detects data link layer
problems that occurred in the “last mile”; monitors the status of the link between the two devices
•CFD (IEEE 802.1ag)
Connectivity fault detection (CFD) provides a Layer 2 link OAM mechanism used for link
connectivity detection and fault locating
Data sheet
Page 7
Additional information
•HPE Intelligent Resilient Framework (IRF)
––Creates virtual resilient switching fabrics, where two or more switches perform as a single
Layer 2 switch and Layer 3 router
––Does not require switches to be co-located and allows them to be part of a disaster-recovery
system
––Allows servers or switches to be attached using standard LACP for automatic load balancing
and high availability
––Simplifies network operation by helping eliminate the complexity of Spanning Tree Protocol,
ECMP, or VRRP
•OAA modules
Support wireless network management and high-performance security applications; leverage
network infrastructure investment
•Green IT and power
Improves energy efficiency through the use of the latest advances in silicon development;
shuts off unused ports and utilizes variable-speed fans, reducing energy costs
•Higher scalability with IRF
Simplifies the architecture of server access networks and reduces cost and complexity; up to
nine HPE 5800 switches can be combined to deliver unmatched scalability of virtualized access
layer switches and flatter, two-tier FlexFabric networks
Warranty and support
•Limited lifetime warranty
See hpe.com/networking/warrantysummary for warranty and support information included
with your product purchase.
•Software releases
To find software for your product, refer to hpe.com/networking/support; for details on the software
releases available with your product purchase, refer to hpe.com/networking/warrantysummary.
Data sheet
Page 8
HPE 5800 Switch Series
SPECIFICATIONS
HPE 5800-24G-PoE+ Switch (JC099B)
HPE 5800-24G Switch (JC100B)
HPE 5800-24G-SFP
Switch with 1 Interface Slot (JC103B)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/
100BASE-TX: half or full;
1000BASE-T: full only
24 RJ-45 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/
100BASE-TX: half or full;
1000BASE-T: full only
24 SFP fixed Gigabit Ethernet SFP ports
1 extended module slot
1 extended module slot
4 fixed 1000/10000 SFP+ ports
4 fixed 1000/10000 SFP+ ports
Additional ports and slots
1 RJ-45 serial console port
1 RJ-45 serial console port
1 RJ-45 serial console port
Power supplies
Included
Included
2 power supply slots
1 minimum power supply required
(ordered separately)
17.3(w) x 16.8(d) x 1.71(h) in.
(43.94 x 42.67 x 4.34 cm) (1U height)
17.64 lb (8 kg)
17.32(w) x 14.35(d) x 1.72(h) in.
(44.0 x 36.45 x 4.36 cm) (1U height)
13.23 lb (6 kg)
17.32(w) x 16.81(d) x 1.72(h) in.
(44.0 x 42.7 x 4.36 cm) (1U height)
18.74 lb (8.5 kg)
2048 MB SDRAM, 512 MB flash; packet
buffer size: 4 MB
2048 MB SDRAM, 512 MB flash; packet
buffer size: 4 MB
2048 MB SDRAM, 512 MB flash; packet
buffer size: 4 MB
4.02 µs (Store and Forward)
(64-byte packets)
155 Mpps
208 Gbps
16000 entries (IPv4)
32000 entries
4.02 µs (Store and Forward)
(64-byte packets)
155 Mpps
208 Gbps
16000 entries (IPv4)
32000 entries
4.02 µs (Store and Forward)
(64-byte packets)
155 Mpps
208 Gbps
16000 entries (IPv4)
32000 entries
32°F to 113°F (0°C to 45°C)
10% to 90%
Low-speed fan: 47.5 dB,
High-speed fan: 52.4 dB
32°F to 113°F (0°C to 45°C)
10% to 90%
Low-speed fan: 42.3 dB,
High-speed fan: 52.9 dB
32°F to 113°F (0°C to 45°C)
10% to 90%
Low-speed fan: 49.6 dB,
High-speed fan: 58.1 dB
50/60 Hz
2968 BTU/hr (3131.24 kJ/hr)
100–120/200–240 VAC
50/60 Hz
358 BTU/hr (377.69 kJ/hr)
100–120–240 VAC
50/60 Hz
498 BTU/hr (525.39 kJ/hr)
100–120/200–240 VAC
Physical characteristics
Dimensions
Weight
Memory and processor
Performance
Latency
Throughput
Routing/Switching capacity
Routing table size
MAC address table size
Environment
Operating temperature
Operating relative humidity
Acoustic
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
1 extended module slot
4 fixed 1000/10000 SFP+ ports
Data sheet
Page 9
HPE 5800 Switch Series
SPECIFICATIONS CONTINUED
HPE 5800-24G-PoE+ Switch (JC099B)
HPE 5800-24G Switch (JC100B)
HPE 5800-24G-SFP
Switch with 1 Interface Slot (JC103B)
Safety
UL 60950-1; EN 60825-1 Safety of Laser
Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950‑1;
CAN/CSA-C22.2 No. 60950-1; Anatel;
ULAR; GOST; EN 60950‑1/A11;
FDA 21 CFR Subchapter J; NOM;
ROHS Compliance
UL 60950-1; EN 60825-1 Safety of Laser
Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950‑1;
CAN‑CSA-C22.2 No. 60950-1; Anatel;
ULAR; GOST; EN 60950‑1/A11;
FDA 21 CFR Subchapter J; NOM;
ROHS Compliance
UL 60950-1; EN 60825-1 Safety of Laser
Products-Part 1; EN 60825‑2 Safety of
Laser Products-Part 2; IEC 60950-1;
CAN/CSA-C22.2 No. 60950-1; Anatel;
ULAR; GOST; EN 60950-1/A11;
FDA 21 CFR Subchapter J; NOM;
ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A;
ICES-003 Class A; ANSI C63.4 2003;
AS/NZSCISPR22ClassA;EN61000-3‑2:2006;
EN 61000-3-3:1995+A1:2001+A2:2005;
EMC Directive 2004/108/EC;
FCC (CFR 47, Part 15) Class A
VCCI Class A; EN 55022 Class A;
ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR 22 Class A; EN 61000‑3‑2:2006;
EN 61000-3-3:1995+A1:2001+A2:2005;
EMC Directive 2004/108/EC;
FCC (CFR 47, Part 15) Class A
VCCI Class A; EN 55022 Class A;
ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR 22 Class A; EN 61000-3-2:2006;
EN 61000-3-3:1995+A1:2001+A2:2005;
EMC Directive 2004/108/EC;
FCC (CFR 47, Part 15) Class A
ETSI EN 300 386 V1.3.3
EN 55024:1998+A1:2001+A2:2003
EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
ETSI EN 300 386 V1.3.3
EN 55024:1998+A1:2001+A2:2003
EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
ETSI EN 300 386 V1.3.3
EN 55024:1998+A1:2001+A2:2003
EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
IMC—Intelligent Management Center;
command-line interface; Web browser;
SNMP Manager; Telnet; HTTPS; RMON1;
FTP
IMC—Intelligent Management Center;
command-line interface; Web browser;
SNMP Manager; Telnet; HTTPS; RMON1;
FTP
IMC—Intelligent Management Center;
command-line interface; Web browser;
SNMP Manager; Telnet; HTTPS; RMON1;
FTP
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
Management
Notes
Services
The customer must order a power supply,
as the device does not come with a PSU.
At least one JD362A or JD366A is required.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/services
for details on the service-level descriptions
and product numbers. For details about
services, and response times in your area,
please contact your local Hewlett Packard
Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/services
for details on the service-level descriptions
and product numbers. For details about
services, and response times in your area,
please contact your local Hewlett Packard
Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/services
for details on the service-level descriptions
and product numbers. For details about
services, and response times in your area,
please contact your local Hewlett Packard
Enterprise sales office.
Data sheet
Page 10
HPE 5800 Switch Series
SPECIFICATIONS
HPE 5800-48G-PoE+
Switch with 1 Interface Slot (JC104B)
HPE 5800-48G
Switch with 1 Interface Slot (JC105B)
I/O ports and slots
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T: full only
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T: full only
1 extended module slot
1 extended module slot
4 fixed 1000/10000 SFP+ ports
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
1 RJ-45 serial console port
Weight
17.32(w) x 16.81(d) x 1.72(h) in. (44.0 x 42.7 x 4.36 cm)
(1U height)
18.74 lb (8.5 kg)
17.32(w) x 14.45(d) x 1.72(h) in. (44.0 x 36.7 x 4.36 cm)
(1U height)
14.33 lb (6.5 kg)
Memory and processor
2048 MB SDRAM, 512 MB flash; packet buffer size: 8 MB
2048 MB SDRAM, 512 MB flash; packet buffer size: 8 MB
Performance
Latency
Throughput
Routing/Switching capacity
Routing table size
MAC address table size
4.02 µs (Store and Forward) (64-byte packets)
190 Mpps
256 Gbps
16000 entries (IPv4)
32000 entries
4.02 µs (Store and Forward) (64-byte packets)
190 Mpps
256 Gbps
16000 entries (IPv4)
32000 entries
Environment
Operating temperature
Operating relative humidity
Acoustic
32°F to 113°F (0°C to 45°C)
10% to 90%
Low-speed fan: 50.5 dB, High-speed fan: 57.9 dB
32°F to 113°F (0°C to 45°C)
10% to 90%
Low-speed fan: 45.3 dB, High-speed fan: 56.5 dB
Additional ports and slots
Physical characteristics
Dimensions
Data sheet
Page 11
HPE 5800 Switch Series
SPECIFICATIONS CONTINUED
HPE 5800-48G-PoE+
Switch with 1 Interface Slot (JC104B)
HPE 5800-48G
Switch with 1 Interface Slot (JC105B)
50/60 Hz
3320 BTU/hr (3502.6 kJ/hr)
100–120/200–240 VAC
50/60 Hz
557 BTU/hr (587.64 kJ/hr)
100–120/200–240 VAC
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST;
EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM;
ROHS Compliance
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST;
EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM;
ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A; ICES-003 Class A;
ANSI C63.4 2003; AS/NZS CISPR 22 Class A;
EN 61000‑3‑2:2006; EN 61000-3-3:1995+A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
VCCI Class A; EN 55022 Class A; ICES-003 Class A;
ANSI C63.4 2003; AS/NZS CISPR 22 Class A;
EN 61000‑3‑2:2006; EN 61000-3-3:1995+A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
ETSI EN 300 386 V1.3.3
EN 55024:1998+A1:2001+A2:2003
EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
ETSI EN 300 386 V1.3.3
EN 55024:1998+A1:2001+A2:2003
EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center; command-line
interface; Web browser; SNMP Manager; Telnet; HTTPS;
RMON1; FTP
IMC—Intelligent Management Center; command-line
interface; Web browser; SNMP Manager; Telnet; HTTPS;
RMON1; FTP
Services
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services,
and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services,
and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
Data sheet
Page 12
HPE 5800 Switch Series
SPECIFICATIONS
HPE 5800-48G-PoE+
Switch with 2 Interface Slots (JC101B)
HPE 5800AF-48G Switch (JG225B)
I/O ports and slots
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T: full only
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T: full only
2 extended module slots
6 fixed 1000/10000 SFP+ ports
1 open module slot
4 SFP fixed Gigabit Ethernet SFP ports
Additional ports and slots
1 RJ-45 serial console port
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
2 fan tray slots
The customer must order fan trays, as fan trays are not
included with the switch. This system requires two
same-direction airflow fan trays to function properly.
The system should not be operated with only one fan tray
for more than 24 hours. The system should not be operated
without a fan tray more than two minutes. The system
should not be operated outside of the temperature range
of 32°F (0°C) to 113°F (45°C). Failure to comply with these
operating requirements may void the product warranty.
Physical characteristics
Dimensions
Weight
17.32(w) x 18.31(d) x 3.39(h) in. (44.0 x 46.5 x 8.61 cm)
(2U height)
39.7 lb (18.0 kg)
17.32(w) x 25.98(d) x 1.72(h) in. (43.99 x 65.99 x 4.37 cm)
(1U height)
22.05 lb (10 kg) shipping weight
Memory and processor
2048 MB SDRAM, 512 MB flash; packet buffer size: 8 MB
2048 MB flash, 512 MB SDRAM; packet buffer size: 8 MB
Performance
Latency
Throughput
Routing/Switching capacity
Routing table size
MAC address table size
4.02 µs (Store and Forward) (64-byte packets)
211 Mpps
284 Gbps
16000 entries (IPv4)
32000 entries
< 5 µs (64-byte packets)
161 Mpps
216 Gbps
16000 entries (IPv4)
32000 entries
Data sheet
Page 13
HPE 5800 Switch Series
SPECIFICATIONS CONTINUED
HPE 5800-48G-PoE+
Switch with 2 Interface Slots (JC101B)
HPE 5800AF-48G Switch (JG225B)
Environment
Operating temperature
Operating relative humidity
Acoustic
32°F to 113°F (0°C to 45°C)
10% to 90%
Low-speed fan: 54 dB, High-speed fan: 58.5 dB
32°F to 113°F (0°C to 45°C)
10% to 90%
Low-speed fan: 60.1 dB, High-speed fan: 69.9 dB
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
50/60 Hz
6278 BTU/hr (6623.29 kJ/hr)
100–120/200–240 VAC
50/60 Hz
426 BTU/hr (449.43 kJ/hr)
100–120/200–240 VAC
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST;
EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM;
ROHS Compliance
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST;
EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM;
ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A; ICES-003 Class A;
ANSI C63.4 2003; AS/NZS CISPR 22 Class A;
EN 61000‑3‑2:2006; EN 61000-3-3:1995+A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
VCCI Class A; EN 55022 Class A; ICES-003 Class A;
ANSI C63.4 2003; AS/NZS CISPR 22 Class A;
EN 61000‑3‑2:2006; EN 61000-3-3:1995+A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
ETSI EN 300 386 V1.3.3
EN 55024:1998+A1:2001+A2:2003
EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
ETSI EN 300 386 V1.3.3
EN 55024:1998+A1:2001+A2:2003
EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center; command-line
interface; Web browser; SNMP Manager; Telnet; HTTPS;
RMON1; FTP
IMC—Intelligent Management Center; command-line
interface; Web browser; SNMP Manager; Telnet; HTTPS;
RMON1; FTP
Notes
The customer must order a power supply, as the device
does not come with a PSU. At least one JC087A, JC090A,
or JC089A is required.
The customer must order a power supply, as the device
does not come with a PSU. At least one JC680A or
JC681A is required.
Services
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services,
and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services,
and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
Data sheet
Page 14
HPE 5800 Switch Series
STANDARDS AND PROTOCOLS
(applies to all products in series)
General protocols
IEEE 802.1ag Service Layer OAM
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s (MSTP)
IEEE 802.1v VLAN classification by
Protocol and Port
IEEE 802.1w Rapid Reconfiguration of
Spanning Tree
IEEE 802.1X PAE
IEEE 802.3ad Link Aggregation Control
Protocol (LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 Telnet
RFC 925 Multi-LAN Address Resolution
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 1812 IPv4 Routing
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 2370 OSPF Opaque LSA Option
RFC 2385 TCP MD5 Authentication for
BGPv4
RFC 2453 RIPv2
RFC 2475 Architecture for Differentiated
Services
RFC 2597 Assured Forwarding PHB
Group
RFC 3046 DHCP Relay Agent Information
Option
RFC 3209 RSVP-TE Extensions to RSVP
for LSP Tunnels
RFC 3576 Ext to RADIUS (CoA only)
RFC 3584 Coexistence between
version 1 and version 2 of the
Internet-standard Network Management
Framework
RFC 3623 Graceful OSPF Restart
RFC 3768 VRRP
RFC 4090 Fast Reroute Extensions to
RSVP-TE for LSP Tunnels
RFC 4291 IP version 6 Addressing
Architecture
RFC 4675 RADIUS VLAN & Priority
RFC 4762 Virtual Private LAN Service
(VPLS) Using Label Distribution Protocol
(LDP) Signaling
802.1r—GARP Proprietary Attribute
Registration Protocol (GPRP)
IP multicast
RFC 2934 Protocol Independent Multicast
MIB for IPv4
RFC 3376 IGMPv3 (host joins only)
RFC 3618 Multicast Source Discovery
Protocol (MSDP)
RFC 3973 Draft 2 PIM Dense Mode
RFC 4601 PIM Sparse Mode
IPv6
RFC 2080 RIPng for IPv6
RFC 2460 IPv6 Specification
RFC 2710 Multicast Listener Discovery
(MLD) for IPv6
RFC 2740 OSPFv3 for IPv6
RFC 2925 Remote Operations MIB
(Ping only)
RFC 3019 MLDv1 MIB
RFC 3162 RADIUS and IPv6
RFC 3315 DHCPv6 (client and relay)
RFC 3315 DHCPv6 (client only)
RFC 3810 MLDv2 (host joins only)
RFC 4022 MIB for TCP
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4293 MIB for IP
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address
Auto-configuration
MIBs
IEEE 8021-PAE-MIB
IEEE 8023-LAG-MIB
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1657 BGP-4 MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2013 SNMPv2 MIB for UDP
RFC 2233 Interface MIB
RFC 2273 SNMP-NOTIFICATION-MIB
RFC 2452 IPv6-TCP-MIB
RFC 2454 IPv6-UDP-MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMPv6 MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-NOTIFICATION-MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2674 802.1p and IEEE 802.1Q
Bridge MIB
RFC 2688 MAU-MIB
RFC 2787 VRRP MIB
RFC 2819 RMON MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
RFC 3826 AES for SNMP’s USM MIB
RFC 4133 Entity MIB (version 3)
LLDP-EXT-DOT1-MIB
LLDP-EXT-DOT3-MIB
LLDP-MIB
Data sheet
Page 15
HPE 5800 Switch Series
STANDARDS AND PROTOCOLS
(applies to all products in series)
Network management
IEEE 802.1AB Link Layer Discovery
Protocol (LLDP)
RFC 2819 four groups of RMON: 1
(statistics), 2 (history), 3 (alarm), and 9
(events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint
Discovery (LLDP-MED)
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
Security
IEEE 802.1X Port Based Network Access
Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
HPE 5800 Switch Series accessories
(applies to all products in series)
Transceivers
HPE X125 1G SFP LC LH40 1310nm Transceiver (JD061A)
HPE X120 1G SFP LC LH40 1550nm Transceiver (JD062A)
HPE X125 1G SFP LC LH70 Transceiver (JD063B)
HPE X120 1G SFP LC SX Transceiver (JD118B)
HPE X120 1G SFP LC LX Transceiver (JD119B)
HPE X120 1G SFP RJ45 T Transceiver (JD089B)
HPE X110 100M SFP LC LH40 Transceiver (JD090A)
HPE X110 100M SFP LC LH80 Transceiver (JD091A)
HPE X115 100M SFP LC BX 10-U Transceiver (JD100A)
HPE X115 100M SFP LC BX 10-D Transceiver (JD101A)
HPE X110 100M SFP LC FX Transceiver (JD102B)
HPE X110 100M SFP LC LX Transceiver (JD120B)
HPE X130 10G SFP+ LC SR Transceiver (JD092B)
HPE X130 10G SFP+ LC LRM Transceiver (JD093B)
HPE X130 10G SFP+ LC LR Transceiver (JD094B)
HPE X130 10G SFP+ LC ER 40km Transceiver (JG234A)
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable (JD095C)
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable (JD096C)
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (JD097C)
HPE X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable (JG081C)
HPE X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable (JC784C)
Cables
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable (QK732A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable (QK733A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable (QK734A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable (QK735A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable (QK736A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable (QK737A)
Power supply
HPE RPS 800 Redundant Power Supply (JD183A)
HPE RPS1600 Redundant Power System (JG136A)
HPE RPS1600 1600W AC Power Supply (JG137A)
SNMPv1/v2c/v3
Access Control Lists (ACLs) Secure
Sockets Layer (SSL)
SSHv2 Secure Shell
Data sheet
HPE 5800 Switch model-specific accessories
HPE 5800-24G-PoE+ Switch (JC099B)
HPE 5800 4-port 10GbE SFP+ Module (JC091A)
HPE 5800 2-port 10GbE SFP+ Module (JC092B)
HPE 5800 16-port Gig-T Module (JC094A)
HPE 5800 16-port SFP Module (JC095A)
HPE 5800 1RU Spare Fan Assembly (JC098A)
HPE 5800-24G Switch (JC100B)
HPE 5800 4-port 10GbE SFP+ Module (JC091A)
HPE 5800 2-port 10GbE SFP+ Module (JC092B)
HPE 5800 16-port Gig-T Module (JC094A)
HPE 5800 16-port SFP Module (JC095A)
HPE 5800 1RU Spare Fan Assembly (JC098A)
HPE 5800-48G-PoE+ Switch with 2 Interface Slots
(JC101B)
HPE 5800 4-port 10GbE SFP+ Module (JC091A)
HPE 5800 2-port 10GbE SFP+ Module (JC092B)
HPE 5800 16-port Gig-T Module (JC094A)
HPE 5800 16-port SFP Module (JC095A)
HPE 5800 300W AC Power Supply (JC087A)
HPE 5800 750W AC Power Supply (JC089A)
HPE 5800 300W DC Power Supply (JC090A)
HPE 5800 PoE Module (JC097B)
HPE 5800 2RU Spare Fan Assembly (JC096A)
HPE 5820 VPN Firewall Module (JD255A)
HPE 5800-24G-SFP Switch with 1 Interface Slot
(JC103B)
HPE 5800 4-port 10GbE SFP+ Module (JC091A)
HPE 5800 2-port 10GbE SFP+ Module (JC092B)
HPE 5800 16-port Gig-T Module (JC094A)
HPE 5800 16-port SFP Module (JC095A)
HPE 5500 150WAC Power Supply (JD362A)
HPE 5500 150WDC Power Supply (JD366A)
HPE 5800 1RU Spare Fan Assembly (JC098A)
HPE 5800-48G-PoE+ Switch with 1 Interface Slot
(JC104B)
HPE 5800 4-port 10GbE SFP+ Module (JC091A)
HPE 5800 2-port 10GbE SFP+ Module (JC092B)
HPE 5800 16-port Gig-T Module (JC094A)
HPE 5800 16-port SFP Module (JC095A)
HPE 5800 1RU Spare Fan Assembly (JC098A)
HPE 5800-48G Switch with 1 Interface Slot (JC105B)
HPE 5800 4-port 10GbE SFP+ Module (JC091A)
HPE 5800 2-port 10GbE SFP+ Module (JC092B)
HPE 5800 16-port Gig-T Module (JC094A)
HPE 5800 16-port SFP Module (JC095A)
HPE 5800 1RU Spare Fan Assembly (JC098A)
HPE 5800AF-48G Switch (JG225B)
HPE 58x0AF 650W AC Power Supply (JC680A)
HPE 58x0AF 650W DC Power Supply (JC681A)
HPE 58x0AF Back (power side) to Front (port side) Airflow Fan Tray (JC682A)
HPE 58x0AF Front (port side) to Back (power side) Airflow Fan Tray (JC683A)
Learn more at
hpe.com/networking
Sign up for updates
Rate this document
© Copyright 2010–2015 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change without notice.
The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall
not be liable for technical or editorial errors or omissions contained herein.
sFlow is a registered trademark of InMon Corp.
4AA3-0731ENW, November 2015, Rev. 11
Download PDF

advertising