HOW TO APPLY HERCULINER APPLICATION TIPS

™
™
HERCULINER
APPLICATION TIPS
SURFACE PREPARATION IMPORTANT
READ CAREFULLY!
HERCULINER will bond to all prepared, clean, thoroughly
dry surfaces. On sound-painted surfaces, paint must be
fully dried or cured to manufacturer’s specifications. The
solvents in HERCULINER will not soften or attack properly
dried or cured paint.
GENERAL DIRECTIONS
Always clean the surface of all oily or waxy contaminants
by using recommended cleaning solvent–leave no residue.
DO’S AND DON’TS
DO
• Thin HERCULINER with Xylene (Xylol) only.
• Use Xylene (Xylol) if available, otherwise use Acetone
or MEK cleaning solvent only for surface preparation.
• Allow solvent to dry completely before applying
HERCULINER.
• Clean surface with strong aggressive detergent.
• Ensure surface is completely dry and/or cured if
recently painted, before applying HERCULINER.
• Test doubtful surfaces with HERCULINER beforehand.
• Apply 2nd coat within 24 hours of 1st coat application.
• Wear chemical resistant gloves.
DON’T
• Mix any solvent with HERCULINER except for Xylene
(Xylol).
• Clean surfaces with lacquer thinners or any solvent
containing alcohol, which will prevent HERCULINER
from curing.
• Assume surface is clean unless you have cleaned
it yourself.
• Apply HERCULINER if temperature is below 32˚F or
above 95˚F.
• Use a laquer-based primer.
• Be thoroughly cleaned with a muriatic acid wash.
1. Use 45% to 50% muriatic acid solution.
2. Agitate solution on surface with a hard-bristled
deck brush.
3. Rinse off with 5% ammonia/water solution.
4. Dry completely.
5. Brush off residue.
• Be wiped with Xylene (Xylol), Acetone or MEK
cleaning solvent.
• Allow solvent to dry completely before applying
HERCULINER.
Sealed concrete should be tested for HERCULINER adhesion:
1. Clean surface thoroughly.
2. Roughen surface.
3. Wipe with Xylene (Xylol), Acetone or MEK
cleaning solvent.
4. Allow solvent to dry completely before applying
HERCULINER.
5. Apply HERCULINER.
6. If delamination occurs, sealer must be removed by
mechanical means (i.e., shot blasting).
For surface preparation of oil or chemically soaked
concrete or other unusually difficult surfaces,
contact HERCULINER toll-free at 800-477-5847.
CONCRETE PLUS PRIMER
HERCULINER exhibits good adhesion to new acrylic and
polyurethane primers applied and overcoated to manufacturers
recommendations. Be sure to apply HERCULINER within
time specifications of primer manufacturer.
ASPHALT
1. Prime surface with a mineral spirit or water-based
driveway sealer according to
manufacturer’s specifications.
2. HERCULINER can then be applied.
ALUMINUM
Roughen surface and use primer compatible with aluminum
and one part polyurethane. If needed, use a primer specifically made for aluminum. If in doubt make a small test
application first. Contact HERCULINER for technical assistance toll-free at 800-477-5847.
METAL
All smooth metal should be cleaned and aggressively
roughened. HERCULINER adheres well to sound-painted
metal. Most rough metal surfaces need not be primed;
however, on applications of extreme wear, such as step
nosings, a primer is recommended.
RUBBER
Clean well using detergent or cleaning solvent, removing
all oil, grease, wax and dirt. Rinse well and allow to dry.
Roughen surface aggressively and then clean with Xylene
(Xylol), Acetone or MEK cleaning solution. Allow solvent to dry
completely before applying HERCULINER. HERCULINER coating will not bond to chlorinated rubber.
FIBERGLASS
Good adhesion can be obtained on unweathered
gel-coated glass, rough fiber, side molded glass, and
smooth-mold resin-side glass. Surface should be free of
oils, waxes and other production additives, then sanded
to remove all gloss, leaving a rough surface.
HOW TO APPLY
HERCULINER may be applied with a brush, roller, or spray
gun. A roller will provide the roughest final texture; a
spray gun the least.
HERCULINER can be applied between 32˚F and 95˚F.
Before applying HERCULINER, it is important that the
surface to be coated is completely clean.
(See surface preparation).
Mask all areas not to be coated. Remove masking tape
immediately after application of second coat.
IMPORTANT!
HERCULINER contains flammable solvents. Ensure proper
ventilation and fire precautions.
ROLLER APPLICATION
Apply HERCULINER with the special open foam stipple
roller included in the kit. Extra roller covers are available
at your local home supply outlet (i.e., foamPro textured
paint roller #58).
Apply first coat as a thin coat to cover. When surface is
touch dry or no longer tacky (usually within 1-4 hours slightly longer for red and gray HERCULINER), apply second coat. Extreme climate conditions of heat, cold and
humidity can shorten or lengthen this period. NOTE:
Failure to apply two complete uniform coats will compromise the durability and reduce the longevity of the HERCULINER truck bed coating. Roll gently to extend the life of
the roller cover.
To avoid “mud cracking,’’ do not apply HERCULINER too
thickly. Pour only Xylene (Xylol) thinner/cleaner over
rollers between coats so rollers will not dry out.
SURFACE PREPARATION FOR
SPECIFIC ADHESION
RUST
BRUSH APPLICATION
IMPORTANT!
The following information is provided only as a guide,
since surfaces can differ significantly. Testing surfaces to
ensure proper adhesion is recommended.
All rust should be removed down to the bare metal before
applying HERCULINER.
WOOD
If wood texture is rough, it may not require special
preparation. For best results, lightly sand wood surface
before applying HERCULINER. Some pressure-treated
woods may need priming. If in doubt, make a small test
application first. HERCULINER will bond to wolmanized
treated wood without priming.
HERCULINER can be applied with a soft paint brush in
two coats at right angles to one another. (HERCULINER
is not a paint, and should be laid onto the surface, in one
direction, not brushed out as an oil or latex paint.)
Between coats, clean brush only with recommended
thinner/cleaner Xylene (Xylol). The second coat can be
applied as soon as the first coat is touch dry (usually
within 1-4 hours - slightly longer for red and gray HERCULINER.) Extreme climate conditions of heat, cold and
humidity can shorten or lengthen this period.
PAINT AND VARNISH
COVERAGE (2 COATS)
1.
2.
3.
4.
One quart covers a flat area of about 15 square feet. One
gallon covers 55 to 60 square feet, with a final dry coat
thickness of 1/16 - 1/32 of an inch.
CONCRETE
For best results, new concrete should:
• Be fully cured for at least 28 days.
• Have a brush finish.
• Be hand troweled (power troweling may overwork
the concrete).
• Be thoroughly cleaned with a citric cleaner
or equivalent.
• Be wiped with Xylene (Xylol), Acetone or MEK
cleaning solvent.
• Allow solvent to dry completely before applying
HERCULINER.
For best results, old concrete should:
• Be completely dry before application of HERCULINER.
Remove all peeling, cracking or chipping paint.
Clean surface thoroughly.
For best results, lightly sand surface.
Wipe with Xylene (Xylol), Acetone or MEK
cleaning solvent.
5. Allow solvent to dry completely before applying
HERCULINER.
2/02
IMPORTANT ADVICE!
• HERCULINER should be stirred thoroughly before
applying (preferably with an electric paint mixer).
• Stir periodically to maintain rubber granules
in suspension.
• To avoid “mud cracking,” do not allow HERCULINER
to pool.
• HERCULINER is a moisture-cured product.
An open or partially used can will thicken and
eventually become unuseable.
• If the product thickens slightly, it can be thinned by
using up to 10% of the recommended thinner/cleaner
Xylene (Xylol) without affecting performance. Use only
Xylene (Xylol) to dilute HERCULINER, clean rollers,
brushes, spray guns and hoses.
IMPORTANT: Other solvents can cause product
failure. Do not dilute HERCULINER or clean rollers,
brushes or spray guns with alcohol or lacquer thinners.
• Once the consistency of the product has become pasty,
it should be discarded.
• Normally, HERCULINER can be subjected to light foot
traffic within 12 hours and should not be subjected to
cleaning or chemical exposure until fully cured, in
2-4 days (approximately 96 hours - slightly longer for
red and gray HERCULINER).
• HERCULINER takes about four days to fully cure: less
time in hot humid conditions, and more time in cold
dry weather.
PLEASE NOTE that full curing time only affects
the amount of time required to wait before subjecting
the surface to cleaning and chemical exposure.
Surface can be subjected to loading well before
this minimum time requirement (see above).
SPRAY APPLICATION
• When using a spray compressor, the operator should always
wear a respirator with chemical absorbing cartridges.
• Make sure to thoroughly mix HERCULINER. A drill with a
mixing adapter works best. If needed, HERCULINER can
be thinned up to 15% with Xylene (Xylol) only.
• Attach spray gun to compressor line, giving pressure
of 40 to 50PSI. Minimum requirements of air
compressor: 11-16 CFM @ 50PSI.
• To initially adjust the air/HERCULINER mix, always start
with the air pressure. Then slowly raise the fluid
pressure gradually lowering the air pressure until the
desired flow rate and spray is reached. NEVER open the
fluid valve first. This will cause the fluid to back up in
the gun due to the lack of air atomization pressure. Air
and fluid pressures should be equal. Always favor
the air pressure side. However, if the air pressure is
too high, fluid flow will reduce to zero.
• Before starting the job, spray a few short bursts
away from the surface to test that everything is
working properly.
• Spray an even coat over the entire surface to be
covered. Be careful not to apply coat too thickly.
• When surface becomes tacky–between 20 minutes
and one hour, depending on weather conditions–spray
second coat. Extreme climate conditions of heat, cold
and humidity can shorten or lengthen this period.
• Clean spray gun and wipe off hoses between coats and
immediately after job is completed. Use Xylene (Xylol)
only.
• Any further questions with regard to spraying, please
call toll free 1-800-477-5847.
• Solvents released when spraying are flammable.
Observe all fire precautions. Proper ventilation
is required.
REPAIRING HERCULINER
HERCULINER can easily be repaired or over-coated,
because it bonds to itself.
• Cut out all damaged HERCULINER to eliminate
uneven edges.
• Clean area to be repaired and rough up surrounding
HERCULINER with 60-grit sandpaper so
that the new application can get a good grip.
• Clean area with Xylene (Xylol) only.
• Brush or spray fresh HERCULINER onto cleaned areas,
as per application instructions.
PAINTING HERCULINER
• A polyurethane based paint will generally adhere to
HERCULINER if it is clean, dry and properly roughened.
• Tinting of HERCULINER is not recommended.
THE CARE AND MAINTENANCE OF
HERCULINER SURFACES
Once HERCULINER has fully cured, it is very easy to
maintain. Because HERCULINER cures to an impermeable
membrane, all dirt sits on the surface.
1. Use any general floor cleaner, from a neutral
commercial cleaner to a household cleaner, or its
equivalent.
2. IMPORTANT! For best results, use a stiff bristled deck
brush to agitate cleaner on the surface. (A cotton
mop is not recommended since pieces of mop may
get caught on high profile HERCULINER surface.
A synthetic fiber material mop, may be used if a deck
brush is unavailable.)
3. Rinse surface thoroughly to remove all residue.
4. Remove all water with sponge mop, 24oz. mop or
water vacuum.
5. Avoid contact with brake fluid and alcohol.
REMOVAL OF STICKY SUBSTANCES
The removal of sticky substances, such as chewing gum,
from HERCULINER can be achieved by the periodic use of a
pressure washer. A water-pressure spray of 600 to 700 PSI,
at an angle of 35-40 degrees, should enable the removal of
the substance within 10 to 15 seconds. This will allow the
removal without damaging HERCULINER.
REMOVAL OF ORGANIC STAINS
Organic stains, such as leaves, can be removed using
a disinfectant solution that contains a form of ammonium
chloride or a slightly acidic cleaner with a PH as close to
neutral as possible. Leave on for 5 to 10 minutes. Rinse off
according to cleaner manufacturer’s recommendations.
PRECAUTIONS
Avoid contact with skin and eyes. Can cause irritation.
AVOID BREATHING VAPOR. USE IN A WELL VENTILATED
AREA. May cause coughing and lung irritation, headache,
dizziness, nausea. If swallowed contact doctor or poison
control center. Do not induce vomiting. Give a glass of
water. If skin contact occurs, wipe clean with Xylene (Xylol)
before HERCULINER dries. Remove contaminated clothing
and wash skin thoroughly with soap and water.
If HERCULINER is allowed to dry on hands, soak in warm
soapy water for 10-15 minutes, gently scrubbing affected
area. Then liberally apply moisturizing lotion. HERCULINER
will usually come off within 2-3 days.
WARNING: Keep out of the reach of children.
Contains Polyurethane and 30% Xylene.
WARRANTY
OLD WORLD INDUSTRIES, Inc. warranties this product
against faulty manufacture and defective materials.
OLD WORLD INDUSTRIES, Inc. will not accept product
liability for application or use of this product.
™
To restore a gloss finish after cleaning HERCULINER, apply
HERCULINER UV Topcoat Protectant or a rubber/vinyl
restoration product.
ALTERNATIVE METHODS
For larger areas, where the above is not time efficient,
there are alternatives available to expedite cleaning.
ROTARY MACHINE
A rotary 14" waxing-type machine with a (thickline)
blue pad can be used in place of a deck brush to greatly
increase the square footage that can be cleaned in a
relatively short period of time.
For additional technical assistance
contact:
HERCULINER
4065 Commercial Avenue
Northbrook, IL 60062
Toll-free 1-800-477-5847 FAX 847-559-2021
www.herculiner.com
RINSE-FREE DETERGENT
If a rinse-free detergent is used, the dirty water pick up
can be done with a water vacuum and the job will be
complete at that point.
AUTOMATIC SCRUBBERS
HERCULINER surfaces can also be cleaned with use of
automatic scrubbers. These are machines which in one
pass, put down the washing solution, scrub the surface
with a (blue) pad, and vacuum up the dirty water. It should
be pointed out that the pad pressure used in the scrubber
(using a blue pad) need only be sufficient for the pad to
make light contact with the surface. Heavy scrubbing will
negatively affect the HERCULINER surface.
IMPORTANT ADVICE!
SPECIFIC CLEANING PROBLEMS
• Remove any over-spray immediately with Xylene (Xylol)
or Acetone. HERCULINER is very difficult to remove
once cured.
GREASE SPILLAGE
To clean a HERCULINER surface of a greasy or slippery
solution, it is necessary to use a slightly more aggressive
detergent, containing a degreaser. There are many such
products available from your chemical suppliers.
2/02
Download PDF