XH260L – XH260V - Weiss Instruments

Operating instructions
dIXEL
2.
XH260L – XH260V
TEMPERATURE AND HUMIDITY CONTROLLER
1. GENERAL WARNING
1.1
•
•
•
PLEASE READ BEFORE USING THIS MANUAL
This manual is part of the product and should be kept near the instrument for easy and quick reference.
The instrument shall not be used for purposes different from those described hereunder. It cannot be used
as a safety device.
Check the application limits before proceeding.
1.2
•
•
•
•
•
•
•
•
SAFETY PRECAUTIONS
Check the supply voltage is correct before connecting the instrument.
Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden
temperature changes with high atmospheric humidity to prevent formation of condensation
Warning: disconnect all electrical connections before any kind of maintenance.
Fit the probe where it is not accessible by the End User. The instrument must not be opened.
In case of failure or faulty operation send the instrument back to the distributor or to “Dixell s.r.l.” (see
address) with a detailed description of the fault.
Consider the maximum current which can be applied to each relay (see Technical Data).
Ensure that the wires for probes, loads and the power supply are separated and far enough from each
other, without crossing or intertwining.
In case of applications in industrial environments, the use of mains filters (our mod. FT1) in parallel with
inductive loads could be useful.
1592002717
If is simultaneously present a request of heating (temp< SET_TEMP-dbt) and dehumidifying (RH
> SET_RH+dbH): the dehumidifying action has the priority over the heating action: both the
compressor and the heating relays are energised till the humidity set is reached at this point only
the heating relay is enabled.
4.3 DEHUMIDIFYING ACTION WITH DEHUMIDIFIER RELAY (OA1 = DEH)
The configurable relay is used, (XH260L terminals 3-4, XH260V terminals 11-12) setting the
parameter oA1 =dEH.
NOTE: the LIGHT button is not more available;
Two kinds of de-humidifying are available:
4.3.1 Dehumidifying action with ONLY de-humidifier relay
By setting the parameter tHu = db the de-humidifying action is performed by enabling the de-humidifier
relay when the humidity is higher than SET_RH + dbH.
The relay is switch off when humidity comes back to the SET_RH value.
4.3.2 Dehumidifying action with de-humidifier and compressor relays
By setting the parameter tHu = cHu the de-humidifying action is performed by enabling the dehumidifier and compressor relays together. when the humidity is higher than SET_RH + dbH.
The relays are switched off when humidity comes back to the SET_RH value.
If is simultaneously present a request of cooling (temp>SET_TEMP+dbt) and dehumidifying (RH >
SET_RH+dbH): the cooling action has the priority over the dehumidifying action: only the compressor
relay is energised till the SET_TEMP is reached at this point also the de-humidifier is enabled.
5.
FA NS
The fan control mode is selected by means of the “FnC” parameter:
FnC=C-n fans will switch ON and OFF with the compressor and not run during defrost:;
FnC= O-n fans will run continuously, but not during defrost
FnC=C-y fans will switch ON and OFF with the compressor and run during defrost;
FnC=O-y fans will run continuously also during defrost
6. THE DISPLAY
2. GENERAL DESCRIPTION
The XH260L, 38x185 format, and the XH260V, 100x64 format, are microprocessor controllers, suitable
for applications on medium or low temperature refrigerating units. They control both humidity and
temperature. They have 6 output relays to control compressor, heating elements, defrost, fan dehumidifier and humidifier. They have 2 NTC inputs one for thermostat the other one for defrost. It’s also
present and 4÷20mA input for humidity. There is one digital input (free contact) configurable by
parameter. An output allows the user to programme the parameter list with the “Hot Key”.
3. TEMPERATURE REGULATION
The temperature regulation is performed through neutral zone using compressor and heater output
relays.
ON
OFF
Set point
• Heating output: CUT IN is “SET_TEMP-dbt”, CUT OUT is when the temperature reaches the set
point.
• Compressor output CUT IN is “ SET_TEMP +dbt”, CUT OUT is when the temperature reaches the
set point.
3.1 DEFROST
Two defrost modes are available through the “tdF” parameter: defrost with electrical heater or hot gas.
The defrost interval is control by means of parameter “EdF”: (EdF=in) the defrost is made every “IdF”
time, (EdF=Sd) the interval “IdF” is calculate through Smart Defrost algorithm (only when the
compressor is ON).
To disable the defrost set the MdF parameter to zero
Humidity regulation during a defrost depends on the Hud parameter.
With Hud=no humidity regulation is disabled.
Con Hud=yES humidity regulation is performed also during a defrost.
To display and modify target temperature set point. (SET_TEMP)
To display and modify target humidity set point (SET_RH); in programming mode it selects
a parameter or confirm an operation.
4. HUMIDITY REGULATION
In programming mode it browses the parameter codes or increases the displayed value.
The humidity regulation is performed through neutral zone, by humidifying dehumidifying actions.
Humidity control can be disabled setting the SET_RH to “nu” value. In this case only the temperature
control is perform.
To start a manual defrost: hold it pressed for at least 3s.
In programming mode it browses the parameter codes or decreases the displayed value.
4.1 HUMIDIFYING ACTION
The humidifying action is done enabling the humidifier relay when the humidity is lower than the
“SET_RH-dbH” value.
The relay is switch off when humidity reaches the set values.
Switch ON and OFF the light, if present (oA1=lig)
4.2 DEHUMIDIFYING ACTION WITHOUT DEHUMIDIFIER RELAY (OA1 DIFFERENT FROM DEH)
– STANDARD CONFIGURATION
In this case the dehumidifying action is performed by setting the following parameters in this way:
tHu = c-H kind of dehumidifying by means of heating and compressor relays
oA1 different from dEH:
The heating and compressor outputs are activated together when humidity is higher than SET_RH+dbH
value. Outputs are disabled when humidity comes back to the SET_RH value.
KEY COMBINATIONS
4.2.1 Relation between cooling, heating and dehumidifying
1.
If is simultaneously present a request of cooling (temp>SET_TEMP+dbt) and dehumidifying (RH
> SET_RH+dbH): the cooling action has the priority over the dehumidifying action: only the
compressor relay is energised till the SET_TEMP is reached at this point also the heating relay
is enabled.
+
XH260L-V.doc
Switch ON and OFF the instrument.
XH260L - XH260V
+
+
To lock and unlock the keyboard
To enter the programming mode.
To exit the programming mode.
1/5
Operating instructions
dIXEL
6.1
1.
2.
ICONS AND SYMBOLS
Each LED function is described in the following table.
LED2
LED3
1592002717
Keep the o and n keys pressed together for more than 3 s the o and n keys.
The “POF” message will be displayed and the keyboard is locked. At this point it is
only possible the viewing of the set point or the MAX o Min temperature stored and
to switch ON and OFF the light, the auxiliary output and the instrument.
TO UNLOCK THE KEYBOARD
Keep the o and n keys pressed together for more than 3s.
Temperature Display
Humidity Display
6.8
LED4
LED
Led 4
MODE
ON
°F
ON
FUNCTION
- Instrument in stand by.
- In “Pr2” indicates that the parameter is also present in “Pr1”.
°C
ON
ON
°C
The compressor is running
FLASHING
- Anti-short cycle delay enabled
ON
The defrost is enabled
FLASHING
Drip time in progress
FLASHING
ON
Programming Phase (flashing with LED3)
Heating enabled
FLASHING
Temperature Set programming phase
LED 3
LED 3
LED 2
(temp)
ON
- ALARM signal
ON
Fan is running
ON
The light is on
ON
RH%
ON
Dehumidifying enabled
ON
Humidifying enabled
FLASHING
Humidity Set programming phase
(umid)
6.2
HOW TO SEE AND MODIFY THE SET POINT (TEMPERATURE AND HUMIDITY)
1.
Push and immediately release the SET key: the display will show the Set point
valueand the correspondant set icon starts flashing;
2.
To change the Set value push the o or n arrows within 10s.
3.
To memorise the new set point value push the SET key again or wait 10s.
6.3
TO START A MANUAL DEFROST
1.
Push the DOWN key for more than 2 seconds and a manual defrost will start.
6.4 TO ENTER IN PARAMETERS LIST “PR1”
To enter the parameter list “Pr1” (user accessible parameters) operate as follows:
1.
+
2.
Enter the Programming mode by pressing the SET_RH+ n for few
seconds. (LED2&3 start flashing)
The instrument will show the first parameter present in “Pr1”
6.5 TO ENTER IN PARAMETERS LIST “PR2”
To access parameters in “Pr2”:
1. Enter the “Pr1” level.
2. Select “Pr2” parameter and press the “ SET_RH ” key.
3. The “PAS” flashing message is displayed, shortly followed by “0 - -” with a flashing zero.
4. Use o or n to input the security code in the flashing digit; confirm the figure by pressing “ SET_RH
”.
The security code is “321“.
5.
If the security code is correct the access to “Pr2” is enabled by pressing “ SET_RH ” on the last
digit.
Another possibility is the following: after switching ON the instrument the user can push SET_RH + n
keys within 30 seconds.
NOTE: each parameter in “Pr2” can be removed or put into “Pr1” (user level) by pressing SET_RH + n.
When a parameter is present in “Pr1” LED 4 is on.
6.6 TO CHANGE PARAMETER VALUES
1. Enter the Programming mode.
2. Select the required parameter with o or n.
3. Press the “ SET_RH ” key to display its value (LED2&3 start blinking).
4. Use o or n to change its value.
5. Press “ SET_RH ” to store the new value and move to the following parameter.
To exit: Press SET_RH + UP or wait 15s without pressing a key.
NOTE: the new programming is stored even when the procedure is exited by waiting the time-out.
6.7
HOW TO LOCK THE KEYBOARD
XH260L-V.doc
ON/OFF FUNCTION
By pushing the ON/OFF key, the instrument shows “OFF” for 5 sec. and the ON/OFF
LED is switched ON.
During the OFF status, all the relays are switched OFF and the regulations are stopped;
N.B. During the OFF status the LED4 button is lighted.
7. PARAMETER LIST
REGULATION
dbt half dead band width for temperature: (0,1÷25,5°C; 1÷45°F) this band is place below and
above the temperature set point (SET_TEMP). The compressor is enabled when the temperature
increases and reaches the SET_TEMP + dbt value. It is turned off when it comes back to the
SET_TEMP. The heating output is enabled when temperature is less than SET_TEMP -dbt value
and disabled when the SET_TEMP is reached.
dbH half dead band width for humidity: (0,5÷25,5RH) this band is place below and above the
humidity set point (SET_RH). The dehumidifying action is enabled when the humidity increases
and reaches the SET_RH + dbH value. It is stopped when it comes back to the SET_RH. The
humidifying output is enabled when humidity is less than SET_RH -dbH value and disabled when
the SET_RH is reached.
LS Minimum temperature set point limit: (-50,0°C÷SET; -58°F÷SET) Sets the minimum
acceptable value for the set point.
US Maximum temperature set point limit: (SET÷110°C; SET÷230°F) Set the maximum acceptable
value for set point.
OdS Outputs activation delay at start up: (0÷255 min) This function is enabled at the initial start up
of the instrument and inhibits any output activation for the period of time set in the parameter.
(Light can work)
AC Anti-short cycle delay: (0÷30 min) interval between the compressor stop and the following
restart.
tHu Kind of de-humidifying: db: only with de-humidifier relay (oA1= dEH)
cHu with de-humidifier and compressor relay (oA1= dEH)
c-H: without de-humidifier relay, by means of compressor and heating relays (oA1≠ dEH).
LSH Minimum humidity set point limit: (Lci ÷ Set H) Sets the minimum acceptable value for the
humidity set point.
USH Maximum humidity set point limit: (Set H ÷ uci) Set the maximum acceptable value for
humidity set point.
DISPLAY
CF Measurement unit: °C= Celsius; °F= Fahrenheit
rES Resolution (for °C): allows decimal point display. dE = 0,1°C; in = 1 °C
rEH Resolution for RH%: in = integer; Hd= half digit.
DEFROST
tdF Defrost type: rE = electrical heater (Compressor OFF)
in = hot gas (Compressor and defrost relays ON)
EdF Defrost mode: in = interval mode. The defrost starts when the time “Idf” is expired.
Sd = Smartfrost mode. The time IdF (interval between defrosts) is increased only when the
compressor is running (even non consecutively).
SdF Set point for SMARTFROST: (-30÷30 °C/ -22÷86 °F) evaporator temperature which allows the
IdF counting (interval between defrosts) in SMARTFROST mode.
dtE Defrost termination temperature: (-50,0÷110,0°C; -58÷230°F) (Enabled only when the
evaporator probe is present) sets the temperature measured by the evaporator probe which
causes the end of defrost.
IdF Interval between defrosts: (1÷120h) Determines the time interval between the beginning of two
defrost cycles.
MdF Duration of defrost: (0÷255 min) When P2P = n, no evaporator probe, it sets the defrost
duration, when P2P = y, defrost end based on temperature, it sets the maximum length for
defrost.
dFd Display during defrost: rt = real temperature; it = temperature reading at the defrost start;
Set = set point; dEF = “dEF” label;
dEG = “dEG” label;
dAd Defrost display time out: (0÷255 min) Sets the maximum time between the end of defrost and
the restarting of the real room temperature display.
Fdt Drain down time: (0÷60 min.) time interval between reaching defrost termination temperature
and the restoring of the control’s normal operation. This time allows the evaporator to eliminate
water drops that might have formed due to defrost.
dPO First defrost after start-up: y = Immediately; n = after the IdF time
Hud Humidity control during defrost: no: the humidity control is stopped during the defrost; yES the
humidity control works also during the defrost.
FANS
FnC Fan operating mode: C-n = running when a load is on, OFF during the defrost;
C-y = running when a load is on, ON during the defrost;
O-n = continuous mode, OFF during the defrost; O-y = continuous mode, ON during the defrost;
TEMPERATURE ALARMS
ALC Temperature alarm configuration: rE = High and Low alarms related to Set Point
Ab = High and low alarms related to the absolute temperature.
ALL Low temperature alarm setting:
ALC = rE , 0 ÷ 50 °C or 90°F
ALC = Ab , - 50°C or -58°F ÷ ALU
when this temperature is reached and after the ALd delay time, the LA alarm is enabled,.
ALU High temperature alarm setting:
ALC= rE, 0 ÷ 50°C or 90°F
ALC= Ab, ALL ÷ 110°C or 230°F
when this temperature is reached and after the ALd delay time the HA alarm is enabled.
ALH Temperature alarm recovery differential: (0,1÷25,5°C; 1÷45°F) Intervention differential for
recovery of temperature alarm.
XH260L - XH260V
2/5
Operating instructions
ALd Temperature alarm delay: (0÷255 min) time interval between the detection of an alarm condition
and the corresponding alarm signalling.
dAO Delay of temperature alarm at start-up: (0min÷23h 50min) time interval between the detection
of the temperature alarm condition after the instrument power on and the alarm signalling.
EdA Alarm delay at the end of defrost: (0÷255 min) Time interval between the detection of the
temperature alarm condition at the end of defrost and the alarm signalling.
dot Delay of temperature alarm after closing the door : (0÷255 min) Time delay to signal the
temperature alarm condition after closing the door.
HUMIDITY ALARMS
AHC Humidity alarm configuration: rE = High and Low alarms related to humidity Set Point
Ab = High and low alarms related to the “absolute” humidity.
AHL Low humidity alarm setting: (with AHC = rE: 0 ÷ 50. With AHC = Ab: Lci ÷ AHu)
when this humidity is reached and after the AHd delay time, the HLA alarm is enabled,.
AHu High humidity alarm setting: (with AHC = rE: 0÷50°C. with AHC = Ab: AHL ÷ uci
when this humidity is reached and after the AHd delay time the HHA alarm is enabled.
AHH Humidity alarm recovery differential: (0.5÷20.0) Intervention differential for recovery of
humidity alarm.
AHd Humidity alarm delay: (0÷255 min) time interval between the detection of an alarm condition and
the corresponding alarm signalling.
dHo Delay of humidity alarm at start-up: (0min÷23h 50min) time interval between the detection of
the humidity alarm condition after the instrument power on and the alarm signalling.
doH Alarm delay at the end of defrost: (0÷255 min) Time interval between the detection of the
humidity alarm condition at the end of defrost and the alarm signalling.
doA Open door alarm delay:(0÷255 min) delay between the detection of the open door condition and
its alarm signalling: the flashing message “dA” is displayed.
nPS Pressure switch number: (0 ÷15) Number of activation of the pressure switch, during the “did”
interval, before signalling the alarm event (I2F= PAL).
If the nPS activation in the “did” time is reached, switch off and on the instrument to
restart normal regulation.
8.4 PRESSURE SWITCH (I1F = PAL)
If during the interval time set by “did” parameter, the pressure switch has reached the number of
activation of the “nPS” parameter, the “PAL” pressure alarm message will be displayed. The
compressor and the regulation are stopped. When the digital input is ON the compressor is always
OFF.
If the nPS activation in the did time is reached, switch off and on the instrument to restart
normal regulation.
8.5 HEATING RELAY SAFETY (i1F=Ht)
With i1F=Ht as soon as the digital input is activated for “did” time heating relay is disabled.
The alarm will stop as soon as the digital input is de-activated.
8.6 DIGITAL INPUTS POLARITY
The digital input polarity depends on the “i1P” parameters.
CL : the digital input is activated by closing the contact.
OP : the digital input is activated by opening the contact
9. INSTALLATION AND MOUNTING
Instruments XW240L shall be mounted on vertical panel, in a 150x31 mm hole, and fixed using two
screws ∅ 3 x 2mm. To obtain an IP65 protection grade use the front panel rubber gasket (mod. RG-L).
Instrument XH260V shall be mounted on vertical panel, in a 72x56 mm hole, and fixed using screws ∅
3 x 2mm. To obtain an IP65 protection grade use the front panel rubber gasket (mod. RG-V).
The temperature range allowed for correct operation is 0 - 60 °C. Avoid places subject to strong
vibrations, corrosive gases, excessive dirt or humidity. The same recommendations apply to probes.
Let the air circulate by the cooling holes.
9.1
XH260V: CUT OUT
PROBE INPUTS
Ot Thermostat probe calibration: (-12.0÷12.0°C/ -21÷21°F) allows to adjust possible offset of the
thermostat probe.
OE Evaporator probe calibration: (-12.0÷12.0°C/ -21÷21°F) allows to adjust possible offsets of the
evaporator probe.
O3 Humidity probe calibration: (-10÷10 RH) allows to adjust possible offsets of the humidity probe.
P2P Evaporator probe presence: n= not present: the defrost stops only by time; y= present: the
defrost stops by temperature and time.
P3P Humidity probe presence: n= not present; y= present.
LCI Readout with 4 mA : (-999 ÷ 999). Adjustment of read out corresponding to 4mA signal.
UCI Readout with 20 mA : (-999 ÷ 999). Adjustment of read out corresponding to 20mA signal.
83,5
56
40
XH260L: CUT OUT
165
+1
-1
150
+0.5
-0
+0.5
-0
9.2
31
DIGITAL INPUTS
i1P Digital input polarity: CL : the digital input is activated by closing the contact;
OP : the
digital input is activated by opening the contact
i1F Digital input operating mode: configure the digital input function:
EAL = generic alarm;
bAL = serious alarm mode; PAL = Pressure switch; Ht = heating relay safety; dor = door switch
odc Outputs status when open door: on = normal; Fan = Fan OFF; oFF = all the loads off
rrd Outputs restarting after doA alarm: no = outputs not affected by the doA alarm; yES = outputs
restart with the doA alarm;
did Time interval/delay for digital input alarm:(0÷255 min.) Time interval to calculate the number of
the pressure switch activation when I1F=PAL. If I1F=EAL or bAL (external alarms), “did”
parameter defines the time delay between the detection and the successive signalling of alarms.
OTHER
oA1 Light relay configuration (XH260L terminals 3-4, XH260V terminals. 11-12): ALr = alarm;
dEH = dehumidifier; onF = on/off relay: close with instrument on, open with instrument off; Lig =
light, ESt, dEF not select
Adr RS485 serial address (0÷247) identifies the instrument within a control or supervising system.
Ptb Parameter table: (read only) it shows the original code of the dIXEL parameter map.
rEL Software release: (read only) Software version of the microprocessor.
Prd Probes display: (read only) display the temperature values of the evaporator probe Pb2.
Pr2 Access to the protected parameter list (read only).
1592002717
72
dIXEL
Ø3 x2
9.3
XH260L INOX FINITURE: MOUNTING
8. DIGITAL INPUT
One digital input is present configurable by user by means of the i1F parameter according to the
following descriptions.
1
2
8.1 DOOR SWITCH (I1F = dor)
It signals the door status and the corresponding relay output status through the “odc” parameter: no =
normal (any change); Fan = Fan OFF; oFF = all the loads are switched off.
4
3
Since the door is opened, after the delay time set through parameter “dOA”, the alarm output is
enabled and the display shows the message “dA”.
The status of loads depends on the “rrd” parameter:
with rrd=no outputs are not affected by the doA alarm;
with rrd=yES = outputs restart with the doA alarm;
The alarm stops as soon as the external digital input is disabled again. During this time and then for the
delay “dot” and “doH” after closing the door, the temperature and humidity alarms are disabled.
1
8.2 GENERIC ALARM (I1F = EAL)
As soon as the digital input is activated the unit will wait for “did” time delay before signalling the “EAL”
alarm message. The outputs status don’t change. The alarm stops just after the digital input is deactivated.
8.3 SERIOUS ALARM MODE (I1F = BAL)
When the digital input is activated, the unit will wait for “did” delay before signalling the “bAL” alarm
message. The relay outputs are switched OFF. The alarm will stop as soon as the digital input is deactivated.
XH260L-V.doc
3
4
2
RG-LX gascke
(optional)
10. ELECTRICAL CONNECTIONS
The instruments are provided with screw terminal block to connect cables with a cross section up to 2,5
mm2 for the digital and analogue inputs. Relays and power supply have a Faston connection (6,3mm).
Heat-resistant cables have to be used. Before connecting cables make sure the power supply complies
with the instrument’s requirements. Separate the probe cables from the power supply cables, from the
outputs and the power connections. Do not exceed the maximum current allowed on each relay, in case
of heavier loads use a suitable external relay.
N.B. Maximum current allowed for all the loads is 20A.
XH260L - XH260V
3/5
Operating instructions
8(3)A
250V~
8(3)A
250V~
8(3)A
250V~
1 2
3
5 6
7
4
8
8(3)A
250V~
9 10 11 12 13 14 15
11. HOW TO USE THE HOT KEY
Heater
12. ALARM SIGNALLING
Message Cause
Outputs
“P1”
Thermostat probe failure
Compressor and heating outputs off
“P2”
Evaporator probe failure
Defrost and by time
“P3”
Humidity probe failure
Humidity regulation off
“HA” High temperature alarm
Outputs unchanged
“LA”
Low temperature alarm
Outputs unchanged
“HHA” High humidity alarm
Outputs unchanged
“HLA” Low humidity alarm
Outputs unchanged
“dA”
Door switch alarm
Outputs depending on the odC parameter
“EAL” External alarm
Other outputs unchanged
“BAL” Serious external alarm
Outputs OFF
“PAL” Pressure switch alarm
Outputs OFF
The alarm message is displayed until the alarm condition recoveries.
All the alarm messages are showed alternating with the room temperature except for the “P1” which is
flashing. To reset the “EE” alarm and restart the normal functioning press any key, the “rSt” message is
displayed for about 3s.
12.1 SILENCING BUZZER
Once the alarm signal is detected the buzzer, if present, can be silenced by pressing any key.
12.2 ALARM RECOVERY
Probe alarms : “P1” (probe1 faulty), “P2”, “P3”; they automatically stop 10s after the probe restarts
normal operation. Check connections before replacing the probe.
Temperature alarms “HA” and “LA” automatically stop as soon as the thermostat temperature returns
to normal values or when the defrost starts.
Humidity alarms “HHA” and “LHA” automatically stop as soon as the humidity returns to normal
values.
Door switch alarm “dA” stop as soon as the door is closed.
External alarms “EAL”, “BAL” stop as soon as the external digital input is disabled
Pressure switch alarm “PAL” alarm is recovered by switching OFF the instrument.
13. TECHNICAL DATA
Housing: self extinguishing ABS.
Case: XH260L: facia 38x185 mm; depth 76mm; XH260V: facia 100x64 mm; depth 76mm
Mounting: XH260L: panel mounting in a 150x31 mm panel cut-out with two screws. ∅ 3 x 2mm.
Distance between the holes 165mm
XH260V: panel mounting in a 56x72 mm panel cut-out with two screws. ∅ 3x2mm. Distance
between the holes 40mm
Protection: IP20.
Frontal protection: IP65 with optional frontal gasket mod. RG-L (XH260L); RGW-V (XH260V)..
Connections: Screw terminal block ≤ 2,5 mm2 heat-resistant wiring and 6,3mm Faston
Power supply: 230Vac or 110Vac ± 10%; Power absorption: 7VA max.
Display: double display + icons; Inputs: 1 NTC probe + 4÷20mA probe
Digital input: 1 free voltage
Relay outputs: compressor: XH260L: relay SPST 20(8) A, 250Vac;
XH260V: relay SPST 8(3) A, 250Vac
heather: relay SPST 8(3) A, 250Vac; defrost: relay SPST 8(3) A, 250Vac
fans: relay SPST 8(3) A, 250Vac; humidifier: relay SPST 8(3) A, 250Vac
de-humidifier: relay SPST 8(3) A, 250Vac
Other output : alarm buzzer (optional); Data storing: on the non-volatile memory (EEPROM).
Kind of action: 1B.; Pollution grade: normal; Software class: A.
Operating temperature: 0÷60 °C.; Storage temperature: -25÷60 °C.
Relative humidity: 20÷85% (no condensing)
Measuring and regulation range: NTC probe: -40÷110°C (-58÷230°F)
Resolution: 0,1 °C or 1°C or 1 °F (selectable); Accuracy (ambient temp. 25°C): ±0,5 °C ±1 digit
XH260L
XH260L-V.doc
Hum
Fan
Def
16 17 18 19 20 21 22 23
L
Comp
Supply 115Vac: 14-15 terminals
XH260V
Supply 115Vac: 2-3 terminals
C
MAX
20A
8(3)A250V~
Room
Fan Def N.C. Comp
8(3)A
8(3)A
8(3)A
Hum
8(3)A
14.2
Def.
11.2 HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY (DOWNLOAD)
1.
Turn OFF the instrument.
2.
Insert a programmed “Hot Key” into the 5 PIN receptacle and then turn the Controller ON.
3.
Automatically the parameter list of the “Hot Key” is downloaded into the Controller memory, the
“doL” message is blinking followed a by flashing “End”.
4.
After 10 seconds the instrument will restart working with the new parameters.
5.
Remove the “Hot Key”..
NOTE the message “Err” is displayed for failed programming. In this case turn the unit off and then on if
you want to restart the download again or remove the “Hot key” to abort the operation.
14.1
N
NC
11.1 HOW TO PROGRAM A HOT KEY FROM THE INSTRUMENT (UPLOAD)
1.
Program one controller with the front keypad.
2.
When the controller is ON, insert the “Hot key” and push o key; the "uPL" message appears
followed a by flashing “End”
3.
Push “SET” key and the End will stop flashing.
Turn OFF the instrument remove the “Hot Key”, then turn it ON again.
4.
NOTE: the “Err” message is displayed for failed programming. In this case push again o key if you want
to restart the upload again or remove the “Hot key” to abort the operation.
14. WIRING CONNECTIONS
20(8)A
250V~
Def
8(3)A
250V~
Room
10.1 PROBE CONNECTIONS
The probes shall be mounted with the bulb upwards to prevent damages due to casual liquid infiltration.
It is recommended to place the thermostat probe away from air streams to correctly measure the
average room temperature.
1592002717
8(3)A
dIXEL
Heater
15. DEFAULT SETTING VALUES
Label
Set T
Value Menu
5.0
---
Set H
50.0
---
dbt
dbH
LS
uS
odS
Ac
tHu
2.0
5.0
-40
110
1
1
db
Pr1
Pr1
Pr2
Pr2
Pr2
Pr1
Pr2
LSH
uSH
cF
rES
rEH
tdf
EdF
SdF
dtE
idF
MdF
dFd
dAd
Fdt
dPo
Hud
Fnc
ALc
ALL
ALu
ALH
ALd
dAo
EdA
dot
AHc
AHL
AHu
AHH
AHd
dHo
doH
nPS
doA
ot
oE
o3
P2P
P3P
Lci
uci
i1P
i1F
odc
rrd
did
oA1
0.0
100.0
°C
dE
Hd
rE
in
0
8
8
20
it
30
0
no
no
c-n
Ab
-40.0
110
1.0
15
1.3
20
20
Ab
0.0
100
2.0
15
1.3
20
0
20
0.0
0.0
0.0
no
YES
0
100
oP
dor
oFF
YES
0
Lig
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr1
Pr1
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr1
Pr1
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr1
Pr1
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr1
Pr2
Pr1
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
XH260L - XH260V
Description
Temperature Set Point
Range
LS ÷ uS ( nu = temperature
regulation disabled )
Humidity Set Point
LSH ÷ uSH ( nu = humidity
regulation disabled)
Half dead band width for temperature
0.1°C o 1°F ÷ 25°C o 77°F
Half dead band width for humidity
0.5 ÷ 50
Minimum temperature set point limit
-50.0°C o –58°F ÷ Set T
Maximum temperature set point limit
Set T ÷ 110°C o 230°F
Outputs activation delay at start up
0 ÷ 250 min
Anti-short cycle delay
0 ÷ 30 min
Humidity regulation
db = dehumidifier relay.; cHu
= dehum+ compr.; c-H=
without dehum. relay
Minimum humidity set point limit
Lci ÷ Set H
Maximum humidity set point limit
Set H ÷ uci
Measurement unit
°C ÷°F
Resolution (for °C):
in = integer / dE = decimal
Resolution for RH%:
in = integer / Hd = half digit
Defrost type
rE, rT, in
Defrost mode
In, Sd
Set point for SMART DEFROST
-30 ÷ +30°C / -22÷+86°F
Defrost termination temperature
-50,0÷110°C/ -58÷230°F
Interval between defrosts
1 ÷ 120 h
Duration of defrost
0 ÷ 250 min
Display during defrost
rt / it / SEt / dEF / dEG
Defrost display time out
0 ÷ 250 min
Draining time
0÷60 min.
First defrost after start up
n÷y
Humidity control during defrost
no; yES
Fan operating mode
c-n / c-Y / o-n / o-Y
Temperature alarm configuration
rE = relative / Ab = absolute
Low temperature alarm setting
0°C ÷ 50.0°C / -50.0°C ÷ ALu
High temperature alarm setting
0°C ÷ 50.0°C / ALL ÷ 110°C
Temperature alarm recovery differential
0.1°C o 1°F ÷ 25°C o 77°F
Temperature alarm delay
0 ÷ 250 min
Delay of temperature alarm at start-up
0.0 ÷ 23.5 h
Alarm delay at the end of defrost
0 ÷ 250 min
Delay of temper. alarm after closing the door
0 ÷ 250 min
Humidity alarm configuration
rE = relative / Ab = absolute
Low humidity alarm setting
0 ÷ 50 / Lci ÷ AHu
High humidity alarm setting
0 ÷ 50 / AHL ÷ uci
Humidity alarm recovery differential
0.5 ÷ 25
Humidity alarm delay
0 ÷ 250 min
Delay of humidity alarm at start-up
0.0 ÷ 23.5 h
Alarm delay at the end of defrost
0 ÷ 250 min
Pressure switch number
0÷15
Open door alarm delay
0 ÷ 250 min ( 250 = nu )
Thermostat probe calibration
-12.0 ÷ 12.0
Evaporator probe calibration
-12.0 ÷ 12.0
Humidity probe calibration
-10 ÷ 10
Evaporator probe presence
no = absent / YES = present
Humidity probe presence
no = absent / YES = present
Readout with 4 mA
-999 ÷ 999
Readout with 20 mA
-999 ÷ 999
Digital input polarity
cL =open / oP = close
Digital input configuration
dor / PAL / EAL / bAL / Ht
Outputs status when open door
on / Fan / oFF
Outputs restarting after doA alarm
no = no / YES = yes
Digital input alarm delay
0÷255 min.
Light relay configuration (XH260L
ALr = alarm; dEH =
terminals 3-4, XH260V terminals. 11-12):
dehumidifier; onF = on/off;
Lig = light, ESt, dEF not
select
4/5
Operating instructions
dIXEL
Adr
1
Pr2
Serial address
0÷247 num
Ptb
rEL
Prd
Pr2
1
0.1
-321
Pr2
Pr2
Pr2
Pr1
Parameter table
Software release
Probes display
Access to the protected parameter list
----Pb1÷Pb3
---
1592002717
Dixell S.p.A. Via dell’Industria, 27 - 32010 Z.I Pieve d’Alpago (BL) ITALY
tel. +39 - 0437 - 98 33 - fax +39 - 0437 - 98 93 13
E-mail:dixell@dixell.com - http://www.dixell.com
XH260L-V.doc
XH260L - XH260V
5/5
Download PDF