Receiver REC 300 Digital

Receiver REC 300 Digital
GB
Operating instructions
GB
Operating instructions
The STABILA REC 300 Digital is a simple-to-use receiver for the rapid capture of
rotating lasers. The REC 300 Digital receiver can receive laser beams from rotation
lasers, even when these are invisible to the naked eye.
The distance to the “on line“ position is indicated digitally
We have endeavoured to explain the unit's handling and functioning in as clear
and comprehensible manner as possible. If, however, you still have any unanswered
questions, we should be pleased to provide advice over the telephone at any time
on the following telephone number: 0049 / 63 46 / 3 09-0
Main components
12
13
6
7
9
8
5
100 mm
4”
11
9
1
5
3
10
2
4
1. ON/OFF button
2. Volume button
8. Laser receiver glass
100 mm / 4”
9. “In line” marks
3. Accuracy button
10. Battery compartment cover
4. Measuring unit button
11. Fixing thread for the clamp
5. LCD
6. Vial
7. Beeper
12. Clamp Guides
13. Shock protection
Getting started
Press the ON/OFF button (1). An audio signal and a short flash from the display will
confirm, that the instrument is switched on. The instrument will now calibrate itself.
1.
2.
ON/OFF button
Automatic
calibration
Press the ON/OFF button (1) quickly once (2sec) to switch the instrument off.
If the instrument is not used, it will automatically switch itself off after 30 minutes.
Height difference display: analogue
20 display steps indicate the divergence from the centre of
the laser line. The central bar indicates the “in line” position of the REC 300 Digital. The arrow increases in size as
the distance from the “in line” position increases.
Rapid beeping note
= too high / back
Continuous tone Slow beeping note
= “in line”
= too low / forward
Audio signals
2
Setting the volume
The volume is increased/decreased by repeatedly pressing the button (2): (a)
Loud (a), soft (b) or off.
If the instrument is set to “silent” only a short beep is emitted
when the laser beam is received.
(b)
Height difference display: digital
The distance to the “on line“ position
is indicated by digital figures
Measuring modes
Setting the accuracy level
The icons appear
permanently
2x
The display appears only briefly
Accuracy button
1 sec
Fine
± 1,0 mm
± 0,05 in
± 1/16 in
± 0,005 ft
Coarse
± 5,0 mm
± 0,2 in
± 1/4 in
± 0,02 ft
The setting selected remains in memory after the unit is switched off.
Setting the measuring unit
The display appears only briefly
1 sec
2x
Measuring
unit button
The setting selected remains in memory after the unit is switched off.
Replacing the batteries
LCD
Full:
Batteries
OK
Half:
Initial
Warning
Empty:
Approximately
30 Minutes
Remaining
Slide the battery cover (10) in the direction
of the arrow and insert new batteries in
accordance with the symbols in the battery
compartment.
2 x 1,5V
Mignon cells Alkaline,
Size AA, LR6
Flashing:
Change
Batteries!
Mignon
AA
LR6
Remove the batteries if the unit
will not be used for a long period !
Battery compartment cover. Water-tight. Protection against water and
dust is ensured by the pressure of the cover against the seal. IP 67.
3
Bracket
1. Securing screw - for securing to
the rear side of the receiver.
2. Guide cones - assist in quickly and
securely fixing the bracket to the
receiver.
1
2
3. Reading reference
4. Securing knob. Turning the securing
knob fixes / releases the clamp with
the receiver to / from the levelling staff.
5. Moveable clamping jaw - for fixing to the levelling staff.
4
5
Care and maintenance
Cleaning: Please do not remove dust and dirt from the receiving or display window
by using dry cloths or abrasive materials as this procedure scratches the windows.
A soft cloth and mild soap and water are effective.
The unit may be submerged under water or sprayed with a low pressure hose if
necessary. Do not use any other fluids other than water or glass- cleaner, as they
may attack polymer components.
Prohibited Uses
- Operation without instruction.
- Operation other than the intended uses.
- Opening the detector, except the battery compartment.
- Modification or conversion of the detector.
Important information
- The person in charge of the detector must understand the instructions in this
manual and ensure other users do also.
- Periodically carry out test measurements, particularly after the detector has been
subjected to abnormal use and before and after important measurements.
Positioning and adjustment of the instrument.
When setting up the instrument, take care that the laser beam does not produce
any unwanted reflections from reflective surfaces.
These reflections may also be captured by the receiver and produce incorrect
readings.
Technical data
Accuracy
Fine:
Coarse:
Detectable Spectrum:
Beeper Volumes:
Batteries:
Operating life:
Automatic Shut Off:
Operating temperature range:
Storage temperature range:
± 1,0 mm 0,05 in
1/16 in
0,5/100 ft
± 5,0 mm 0,20 in
1/4 in
2,0/100 ft
610 nm - 780 nm
Loud: ~ 105 dBA
Low: ~ 85 dBA
2 x 1,5V Mignon cells Alkaline , Size AA,LR 6
70 hours
30 minutes
-20°C to +60°C
-40°C to +70°C
Subject to technical modifications.
Guarantee terms and conditions
Stabila provides a guarantee against deficiencies and faults in the assured characteristics because of material or manufacturing faults for a period of 24 months from
date of purchase. Any faults will be eliminated at Stabila's own discretion either by
repairing or replacing the unit. Stabila accepts no wider claims.
No liability is accepted for any faults due to inappropriate treatment (e.g. damage
caused by the unit falling, operation with the wrong voltage or type of current, use of
unsuitable current supply sources) or for any autonomous changes made to the unit
by the purchaser or a third party.
Also no claims under guarantee are accepted for natural wear and tear or any small
faults that do not significantly affect the unit's operation.
Any guarantee claims must be made via the dealer on the duly completed guarantee
form (see last page) to be returned with the unit.
Download PDF