HDMI 1x4 Splitter Over CAT5e/6 Extender - A

ANI-0104HBC
INSTRUCTION MANUAL
HDMI 1x4 Splitter Over CAT5e/6 Extender
A-NeuVideo.com
Frisco, Texas 75034
(317) 456-2461
AUDIO / VIDEO MANUFACTURER
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualified service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.
A NEUVIDEO
TABLE OF CONTENTS
CONTENTS
INTRODUCTION................................................................1
PACKAGE CONTENTS .................................................................1
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
FEATURES .................................................................................... 2
SPECIFICATIONS ......................................................................... 2
OPERATION CONTROLS & FUNCTIONS .................................... 3
SPLITTER ................................................................................ 3
RECEIVER ............................................................................... 4
EDID DESCRIPTION .................................................................... 5
CONNECT & OPERATE ................................................................. 6
Dear Customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this
manual for future reference.
INTRODUCTION
The ANI-0104HBC Splitter is a product for splitting and extending
your HDMI signal over long distances to a compatible display. It is
designed to convert the HDMI signal and transmit by a CAT5E/6
cable. Supports bi-directional infrared control signals together with
the HDMI signal, so you can control either the Source or the Display
device. Supports full HD resolution for 1080p@60Hz@24 bit/pixels.
This product has a 3 year warranty.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and
make sure the following items are contained in the shipping carton:
• ANI-0104HBC HDMI Splitter
We reserve the right to make improvements to this document and/
or product at any time and without notice.
• (4) Receivers
• (4) Wideband IR Tx
• (4) Wideband IR Rx
COPYRIGHT NOTICE
• 12V 2.5A DC Power Supply adapter - Main Unit
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
• (4) 5V 1A DC Power Supply adapter - Receivers
• Users Guide
© Copyright 2016. All Rights Reserved.
Version 2.3 JULY 2015
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
1
A NEUVIDEO
FEATURES & SPECIFICATIONS
FEATURES
• HDMI 1.3, HDCP 1.2 and DVI 1.0 compliant
• Supports full HD resolution for 1080p@60Hz@24 bit/pixels
• HDMI local loop out for the HDMI input
• Supports LPCM 7.1CH, Dolby True HD, and DTS-HD Master Audio
• Operates for TMDS clock frequencies up to 165MHz
• Uses a single CAT5e/6 cable to substitute the HDMI cable to achieve long distance transmissions
• UTP cable termination follows the IEEE-568B standards
• Supports EDID control via EDID selector
• Transfer bi-directional infrared control signal together with the HDMI signal
• ~13 ft IR signal distance to the Remote Control
• The ANI-0104HBC is NOT compatible with EZ-45 connectors
SPECIFICATIONS
• HDMI Splitter Input/Output Ports:
• (2) HDMI female port
• (4) CAT6
• (1) IR Transmitter
• (1) IR Receiver
• Receiver Input/Output Ports:
• (1) HDMI female port
• (1) CAT6
• (1) IR Transmitter
• (1) IR Receiver
• Frequency Bandwidth: 1.485Gbps
• ESD Protection Human Body Model:
• ± 8kV (air-gap discharge)
• ± 4kV (contact discharge)
• Dimensions:
• Splitter (WxDxH): 10.1 x 4.6 x 1 in
• Receiver (WxDxH): 1.9 x 3.2 x 1 in
• Weight: 5.1 lb (Net)
• Splitter: 1.8 lb (Unit only)
• Receiver: 0.2 lb (Unit only)
• Operating Temperature: 0°C ~ 40°C / 32°F ~ 104°F
• Storage Temperature: -20°C ~ 60°C / -4°F ~ 140°F
• Relative Humidity: 20 ~ 90% RH (Non-condensing)
• Power Consumption (Max):
• HDMI Splitter: 12W
• Receivers: 1.5W
• Power Supplies:
HDMI Splitter: DC 12V 2.5AReceivers: (4) DC 5V 1A
As product improvements are continuous, specifications are subject to change without notice.
2
A NEUVIDEO
OPERATION CONTROLS & FUNCTIONS
Splitter
q POWER SWITCH: Power ON\OFF Switch.
w POWER LED: This red LED illuminates when the device is connected with the power supply.
e IR IN: IR controls the system over a CAT5e/6 cable IR Receiver. Source to SINK, plug Wideband IR Rx into this unit.
r IR OUT: IR controls the system over a CAT5e/6 cable IR Transmitter. SINK to Source, plug Wideband IR Tx into this unit.
t EDID SELECTOR: Select output signal format via EDID Selector.
y UPDATE: For system software updates.
u OUTPUT AREA: (4) RJ-45 Jacks provided per signal output.
i HDMI LOOP OUT: Local HDMI loop output port.
o HDMI INPUT: HDMI Input port. Connects source with HDMI cable.
a DC IN: Plugs the 12V 2.5A DC power supply into the unit.
3
A NEUVIDEO
OPERATION CONTROLS & FUNCTIONS
receiver
q CAT6: Connects the CAT input of the receiver with the CAT output of the transmitter with a CAT5e/6 cable.
w EQ SELECTOR: Equalizer selector. See the EQ description.
e LOCK LED: This red LED will illuminate when the Splitter and Receivers are connected with a CAT5e/6 cable.
r HDMI OUT: HDMI Output port. Connects to a TV with a HDMI cable.
t DC IN: Plugs the 5V1A DC power supply into the unit.
y IR RX: IR controls the system over a CAT5e/6 cable IR Receiver. SINK to Source, plug Wideband IR Rx into this unit.
u IR TX: IR controls the system over a CAT5e/6 cable IR Transmitter. Source to SINK, plug Wideband IR Tx into this unit.
4
A NEUVIDEO
EDID Description
TX EDID Description
Under normal circumstances, a source device (digital and analog) will require information about a connected device/display to assess
what resolutions and features are available. The source can then cater its output to send only resolutions and features that are compatible
with the attached device/display. This information is called EDID (Extended Display Information Data) and a source device can only
accept and read one EDID from a connected device/display. Likewise, the source can only output one resolution for use by a connected
device/display.
The EDID switch allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the display and
source.
Attention: Please confirm the extender is working normally, when you want to modify the new EDID to source. Toggle
the EDID switcher to the corresponding number first, then plug in the Transmitters power again. The extender will send
the new EDID to the source.
EDID TABLE:
POSITION
EDID DESCRIPTION
POSITION
EDID DESCRIPTION
0
1080p, 2CH AUDIO
8
3D,1080p, HD AUDIO
1
1080p, DOLBY/DTS 5.1
9
Copy the HDMI loop out EDID
2
1080p, HD AUDIO
A
1080p, 2CH AUDIO
3
1080i, 2CH AUDIO
B
1080p, 2CH AUDIO
4
1080i, DOLBY/DTS 5.1
C
1080p, 2CH AUDIO
5
1080i, HD AUDIO
D
1080p, 2CH AUDIO
6
3D,1080p, 2CH AUDIO
E
1080p, 2CH AUDIO
7
3D, 1080p,DOLBY/DTS 5.1
F
1080p, 2CH AUDIO
RX EDID Description
RECOMMENDED EQ SETTING
POSITION
CABLE LENGTH
0 (MIN)-2
under 15M (49.5ft)
3-4
15-30M (49.5 ft - 99ft)
5-6
30-40M (99ft - 132ft)
7 (MAX)
40-50M (132ft - 164ft)
If you see flickering or a blinking image on the display, adjust
the EQ switch to improve the cable skew. MAX stands for the
strongest HDMI signal level for the longest possible transmission
length while MIN stands for the weakest HDMI signal level for short
transmission lengths. Adjust the signal level from MIN to MAX until
desired video quality is displayed.
5
A NEUVIDEO
CONNECT & OPERATE
Application Example
1. Connect a source such as a Blu-Ray player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the
Transmitting unit.
2. Connect a display such as a HDTV or HD Projector to the HDMI output on the receiving units.
3. Connect a single CAT5e/6 up to 164ft/50M to the output of the Transmitting unit, and the other end to the input of the receiving units.
4. For power, plug both the transmitting unit and receiving units to the included power supplies.
5. Power on each device in the same sequence (The receiver and transmitter will already be powered when either unit is plugged in.)
At this point the display connected should display the source signal connected to the extender set. If no signal is displayed, check the
receiver EQ switcher. If a display is having difficulty receiving a signal, see the EDID section and perform EDID learning or access the
display’s menu and adjust the resolution (lowest to highest until signal is displayed). A 24Hz vertical refresh rate may work better than
60Hz or higher. Use the source remote at the receiver emitter to test IR functionality. If the IR remote function is not responding, check the
emitters to ensure they are placed correctly and are plugged into the correct IR jacks on the extender sets receiving and transmitting units.
Wideband IR (30KHz---60KHz) introduction
IR RECEIVER (RX):
• To control the source: Plug IR Receiver into the IR RX port of the receiver unit; place the receiver at or near the display.
• To control the display: Plug the IR Receiver into IR RX port of the transmitter unit; place the receiver in position where it is able to
receive remote signals.
IR BLASTER (TX):
• To control the source: Plug the IR Blaster into IR TX port of the transmitter unit; place the blaster in front of the IR eye of the source.
• To control the display: Plug the IR Blaster into IR TX port of the receiver unit; place the blaster in front of the IR eye of the display.
6
A NEUVIDEO
CONNECT & OPERATE
IR CONTROL DISPLAY TO SOURCE
7
A NEUVIDEO
CONNECT & OPERATE
IR CONTROL SOURCE to DISPLAY
8
THIS PAGE IS INTENTIONALLY LEFT BLANK.
A NEUVIDEO
TERMS AND CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at
the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice
to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are
licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use
only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only.
A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual
property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any
manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be
relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies
or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT
TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY
A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU
PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
10