TR8100v THERMOSTAT
TR8100V Thermos tat Instructions
ver 1.0
LCD symbols
Symbol
Event
Symbol
AUTO
The buttons are locked
Override
Heating is turned on
Err
Frost protection activated
Event
Automatic mode, executes the programmed schedules
Temporary temperature override
The floor sensor is not being read by the thermostat
Program number
Economy temperature
Manual mode
Comfort temperature
Configuration Menu
To enter into the setting menu please follow the steps below:
Step 1, Turn the thermostat off by pressing
Step 2, Press
MENU
POWER
;
, you will then see menu 01.
Step 3, Use the up and down arrows to adjust the sensor selection which is Menu 01(Air sensing;Air and Floor, or Floor only)
Step 4, Press
NEXT
Setp 5, Press
DONE
Menu #
01
to move to the next Menu and once you have all the menu options set,
to accept and store.
Feature
Mode/Sensor selection
Explanation
Adjustment (press up & down buttons to adjust)
This thermostat is a combination model which allows you
to choose 3 different modes.
A, AF, F
A mode = Air Sensing Only(Has built in sensor)
AF mode = Air & Floor sensing(Floor probe must be installed)
F mode = Floor Sensing(Floor probe must be installed)
The number of degrees difference before switching.
The default is 1°C which means the thermostat will switch
the heating on 0.5°C below the set temperature and will turn
it off 0.5°C above the set temperature.With a 2°C differential
the heating will switch on 1°C below the set temperature
and will switch off 1°C above the set temperature.
1°C, 2°C....10°C ( 1°C by default)
02
Switching Differential
03
Air Temp Calibration
This is to recalibrate the air temperature if required.
-1°C = decrease 1 °C, 1°C = increase 1°C...
04
Floor Temp Calibration
This is to recalibrate the floor temperature if required.
-1°C = decrease 1 °C, 1°C = increase 1°C...
05
Temperature Readout
(AF mode only)
This gives you the option to show the Air Temperature,
A= to show air temperature, F=to show floor temperature,
Floor Temperature or to show both Air & Floor at intervals. A--F = to show both in 5 second intervals
06
Maximum Floor Temp
( AF mode only)
This is to protect the floor surface.
07
Temperature Format
This alows the temperautre to be set to show °C or °F.
08
Clock Format
You can select the clock to show in either 12 or 24 hour time
09
Frost Protection
This is to avoid your room temperature going below 5°C
on= activated, off= deactivated
10
5+2 / 7 Day Mode
This allows you to program either 5 days at once, then the
2 days of the weekend separately, or a full 7 days at the
same time or 7 days separately
01 = 5+2 day programmable
02 = 7 day programmable
20°C~ 40°C (40°C by default)
C or
F
24 (default), 12- hour or 24-hour clock format
Setting the clock and day of the week
This thermostat is fitted with a real time clock. It is essential that the clock time and day are set accurately if you require your programmed events
to start on time. To set follow the steps below:
1) Touch the time display and the time will start flashing. Use the up and down arrows to set the time.By holding the arrow down the time will change faster.
2) Press
NEXT
3) Press
DONE
to move to the Day setting and use the up and down arrows to get to the correct day.
to store and exit.
See overleaf for further setting up information
Page1
TR8100V Thermostat Instructionsver 1.0
Setting the Program Schedules
This thermostat has the ability to program each individual day of the week separately, or program 7 days of the week at once. You can also program weekdays
(5 days) to one schedule and then weekends (2 days) to a different schedule. See the Menu information for details on how to set this up.(refer to Menu 10)
Program
Start Time Setpoint
WAKE
1
22 °C
Set to the time you would like to wake to and the temperature you want during the morning, until you left for the day.
LEAVE 16 °C
Set to the time you leave home and the temperature you wish your home to maintain while you are away at work perhaps.
07:00
2
Explanation
09:30
3
RETURN
16:30
22 °C
Set to the time you return home at end of the day and the tempe rature you want during evening until bed time.
4
SLEEP
16 °C
Set to the time you sleep and the temperature you want overnight(usually a comfortable and energy saving temperature).
22:30
Above are default program schedules, to make changes, follow ea sy steps as below.
1.
Press
2.
Use
(Press
3.
Press
4.
Use
5.
Press
6.
Use
7.
Press
SCHEDULE
and the day display will start flashing. (If your thermostat is set to 5+2 day programmable mode, the programming will skip to step3)
to adjust the day of the week you want to start programming or to the day you wish to edit an existin g event / program.
to select all 7 days of the week, and to cancel press
ALL DAYS
NEXT
the LCD screen will show Program 1(
and
again.)
) and the time will be flashing.
to adjust the time you wish the Program 1 event to commence for the selected day/days.
and the temperature will start flashing.
NEXT
and
NEXT
ALL DAYS
to set the desired temperature to be maintained during Program 1.
and the LCD screen will show Program 2 with the time display flashing, this signifies that the second daily event is now ready to be programmed.
Repeat steps 4,5,6 to set the remaining programs/events, then press
Hint: During setting programs, press
DELETE
DONE
to store and exit.
will clear a program entry and thermostat will maintain the temperature setpoint of the last executed program
until the beginning of the next program.
Auto / Manual Mode
Press
MODE
to select Auto/Manual mode. In Manual mode(
), the
thermostat maintains a constant set temperature manually set by the user.
In Auto mode, the thermostat executes the preprogrammed schedules.
Carefully separate the front half of the thermostat from the back plate by placing a small
flat head terminal driver into the slots on the bottom face of the thermostat.
Carefully unplug the ribbon connector which is plugged in to the front half of the thermostat.
Holiday Function
The Holiday function reduces the temperature in your room to the frost protection
temperature. The thermostat will maintain this temperature for the duration of the
holiday and will then automatically return to the program mode on your return.
or
Installation and Wiring
Press
HOLIDAY
, enter the duration of your holiday by
Press
DONE
. To cancel a Holiday,reduce the holiday period to 00 days.
Place the thermostat front half somewhere safe. Terminate the thermostat as shown in
the diagrams below.
Screw the thermostat back plate on to the flush box
Re-connect the thermostat ribbon cable and clip the two halves together.
.
L
N
N
L
Lock the Keypad
To lock the keypad, press and hold the top left corner of display for 5 seconds,
you will see a lock symbol
. To unlock, repeat the steps above and the
lock symbol will disappear.
Floor Sensor
Reset to Factory Setting
With thermostat turned off, press and hold OFF for 5 seconds until you can
see -- : -- on LCD.
Temporary Temperature Override
FEED
(230VAC)
LOAD (16A)
Touch the temperature display, and it will start to flash. Use up or down
buttons to adjust. Press
DONE
to accept, and you will see “Override”
above the temperature display. Thermostat will maintain the new set
temperature until the next programmed event(comfort level). To cancel
the override setting, press
This product should be installed by
a qualified electrician.
RUN
SCHEDULE
Page 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement