Parts list for the TP501 4

Parts list for the TP501 4
Parts list for the TP501 4-gallon Backpack Sprayer
TM
PARTS LIST
7EK-2 181
4
6 5EK-2
9 10
6
7EK-2
5EK-2
9
181 7EK-2
5EK-2
5EK-2
51E 44E 12.1
51E 44E 12.1
51E 44E 12.1
51E 44E 12.1
1EK
36 15
1EK 2A
1EK 2CH
44E 51E
51E 44E 12.1
51E 44E 12.1
1AS
289
31 15
284 15
12.1 44E 51E
44E 48E 397
44E 48E 397
4
4 5EK-2
44E 45E
44E 46E
15 31 283
46E 44E
14A 44E
4
5EK2 4
47E
47E
17 18F
9 11P
47E
17
ATTENTION
18F
GRIP
367
SPGREASE
18F
FILT
18F
21 20 18F
19 18F
20 19 18F
19 18F
FOR BEST PERFORMANCE, PERIODICALLY
GREASE PUMPING MECHANISM, ALL
O-RINGS,& SEALS
18F
18F
18F
18F 392
22 23
18F 19 20
24 392
24
21 18F
367 21 20 18F
21 18F
25JT
6” strainer for tank lid
Green lid with seal& check valve
Seal for 6” lid
Check valve for lid
Nylon bearing
T-shaped (45° angle) pump lever
Screw & nut set
Pump handle (fits with t-shaped
pump lever)
Pressure tank
Kit 9
O-ring for pressure tank
Kit 10
Plastic retention clamp
Kit 11P
O-ring and washer set for
Kit 12.1
diaphragm
Crank with brass pin
Kit 14A
Shoulder strap, pad, buckle &
Kit 15
clip (1 each)
Hose set
Kit 17
Complete spray gun with built-in
Kit 18F
filter & grip
Spindle set
Kit 19
Spindle, o-ring, & washer set
Kit 20
Plug set (cap, spring & o-ring)
Kit 21
20” brass spray wand
Kit 22
20” plastic spray wand
+Kit 23
Nozzle holder
Kit 24
Plastic spray tip set (2-8004 & 1
Kit 25JT
Tk5)
Shoulder strap clips
Kit 31
Shoulder pads for use with
Kit 36
shoulder strap
Complete piston & cylinder
Kit 44E
(viton)
Piston only with brass pin
Kit 45E
Connecting rod assembly
Kit 46E
Piston protector (complete)
Kit 47E
Viton piston cup
Kit 48E
Cylinder assembly
Kit 51E
Large locking R-pin for pump
Kit 181
handle
Shoulder strap clips
Kit 283
Heavy padded adjustable
+Kit 284
shoulder straps (2) with hooks
Complete shoulder straps with
+Kit 289
shoulder pads & clips (set of 2)
O-rings (2) for gun grip
Kit 367
Washer set for spray guns
Kit 392
G8 piston cup
+Kit 397
Filter replacement for kit 18F
Kit FILT
Grip replacement for kit 18F
Kit GRIP
+Kit SPGREASE Silicone grease lubricant for all
sprayers.
Kit
Kit
Kit
Kit
Kit
Kit
Kit
Kit
1AS
1EK
2A
2CH
4
5EK-2
6
7EK-2
NOTE: + Not supplied with unit see sheet of
accessories.
1618 Stanford St, Suite C, Santa Monica, CA 90404
For spare parts and accesories, please call:
1-800-286-0679
NOTE:
For best results, the sprayer should be pumped
every 5 seconds on a continuous basis. This will
maintain your spraying pressure. If you do not pump,
you will not have pressure to spray
TM
Parts list for the TP501 4-gallon Backpack Sprayer
We would like to congratulate you on the purcharse of your new backpack sprayer, TP501, cylinder and piston pump
sprayer that allows you the easiest, most comfortable way of carrying out your farm and garden projects.
As a new owner of this skillfully engineered sprayer, we strongly recommend you carefully read and follow all the information
On this sheet before use, and after use, and then save for future reference.
HOW TO ASSEMBLE
1.
Attach spray wand to spray gun and tighten firmly.
2.
Take pump handle kit 7EK-2 (tube) and insert into the tube on the pump lever Kit 5EK-2 (”T” shape lever on
sprayer).
You will notice holes drilled through both sides of both the pump handle and the pump lever. Align these holes,
Take the “R” pin provided and place through the holes. This affixes the handle in place and is ready for use.
For storage reverse process and then place “R” pin through the pump lever Kit 5EK-2 to keep from losing “R” pin
3.
Instructions for installing shoulder strap plastic buckle:
First put the sprayer on a hard flat surfece, take the white plastic buckle and while holding the sprayer up slightly,
Place buckle under the tubular metal frame. Slowly push down forcing the frame into the buckle. Repeat the
Same procedure for other side.
HOW TO PREPARE YOUR UNIT FOR USE
1.
Remove cap.
2.
Mix solution in a separate receptacle, following manufacturers directions on the container.
3.
Pour pre-mixed solutions into sprayer and cap.
4.
Place sprayer on back and pressurize tank by pumping approximately 10 to 15 times. For best results, the
sprayer should be pumped every 5 seconds on a continuous basis. This will maintain your spraying
pressure. If you do not pump, you will not have pressure to spray.
5.
Always oil the seal on cap of unit as well as the check valve, this will extend life of seal and is important for
obtaining proper seal with no leaks.
6.
A unit that has been used with herbicides should never be used to spray insecticides, unless the sprayer has
been properly cleaned and all other chemicals neutralized. Failure to do this could cause you to kill plants that
have been sprayed. Consult with the manufacturer of the chemicals in use to obtain proper instructions.
HOW TO CLEAN AND MAINTAIN
1.
Remove cap and pour out remaining solution, then rinse all parts thoroughly with clean water.
2.
Leaving approximately ½ gallon of fresh water in tank, pressurize and flush pumping systems by depressing
trigger at least 2 minutes, then drain all remaining water.
3.
Use a neutralizing agent (according to manufacturer´s directions) to clean and flush the unit.
4.
Always store tank clean and empty in a dry, shaded location.
CAUTIONS
Failure to follow
manufacturers
recomendation on
use and care of
unit will void any
expressed or
implied warranty.
Do not use chlorine
or clorox. It will
permanently
damage pump
system.
Please read and follow all instructions before using sprayer.
Before using, filling or cleaning any sprayer, read all parts of the operating instructions.
Make sure to set up the sprayer exaclty as explained in the printed operating instructions, reminder tags and /or stickers.
Wear protective clothing, respirator, gloves, eye protection, etc. Whenever using, filling, or cleaning sprayer.
Periodically re-grease lid gasket as well as lid vent and pump cylinder, where applicable.
To ensure good performance, keep lid vent free of obstruction. Before and after each use, make sure all connections are well
tightened.
Service and replace worn parts as required.
Read and follow all instructions of the chemical suppliers.
As a rule, mix your chemicals in a separate container from which to fill the sprayer. Do not mix formulas inside the sprayer. Where
an exception is made (e.g. with liquid fertilizers), fill sprayer with water BEFORE adding the active ingredient.
Always sift formula through the screen. If there is no built-in strainer, use a screened funnel.
Never fill the sprayer with hot liquids. Max. 30ºC, or 85ºF.
This sprayer is made to hadle agrichemicals in their usual water or oil solutions. Do not use flammable, corrosive or cauistic
solutions.
Do not use chlorine or clorox.
Do not use acids.
Never use gasoline or other flammable materials.
Before claning or servicing the sprayer, allow all pressure to escape. Do not store or transport sprayer under pressure.
After each use, wash the sprayer--including hose, lance and shut-off valve--with plenty of fresh water. Unless spraying is to be
continued within hours, drain chemical formula and thoroughly rinse the tank and all liquid ducts.
Never store chemicals in your sprayer for any length of time.
Use the sprayer only for the kind of jobs for which it was designed. When in doubt, ask your dealer.
Do not leave the sprayer in reach of children or persons not qualified to handle it in proper fashion.
When not in use--and specially during prolonged storage---keep your sprayer in a protected place away from direct solar heat.
Make sure the spray hose loops freely without kinking or squeezing.
BN476.012-1109E/EX
Always use SP Systems original replacement part.
Rev.10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement