PSM 200 - CCI Solutions

PSM 200 - CCI Solutions
Model PSM200 User Guide
PSMR200
Personal Monitor System User Guide
>>E2
2002, Shure Incorporated
27B8792 (BJ)
>>P2R
>>P2T
Printed in U.S.A.
ENGLISH
TROUBLESHOOTING
PROBLEM
SOLUTION
No sound at the receiver
Check the power cord on the TransMixer and make sure it is
powered on.
Make sure both the TransMixer and the P2R Receiver are set to
the same frequency channel.
Make sure the earphones are plugged in to the receiver and the
volume is up.
Make sure the Receiver is on and the battery is good.
Check the incoming audio connections on the TransMixer.
Try to maintain line-of-sight between the TransMixer and Receiver
antennas.
Try another frequency in case interference is limiting the range.
Check for television channel interference. More information is
available at www.shure.com.
Make sure no other TransMixers or wireless transmitters are operating on your frequency.
Make sure the TransMixer input level is lighting yellow LEDs for
optimum performance.
Make sure you are using a fresh battery in the P2R.
Make sure the TransMixer input level is lighting yellow LEDs for
optimum performance.
Make sure the P2R Receiver’s volume knob is up.
Low receiver range
Receiver sounds fuzzy or distorted
Low audio output at the receiver
ACCESSORIES
Furnished Accessories
P2T TransMixer
AC Adaptor . . . . . . . . . . . . . . . . . . . . . PS20, PS20E, PS20UK
Single Mount Rack Bracket . . . . . . . . . . . . . . . . . . . . . 53A8484
Dual Mount Rack Bracket . . . . . . . . . . . . . . . . . . . . . . 53B8484
Straddle Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53A8443
Hardware Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90AD8100
P2R Receiver
1/4-inch mono 20 foot cable . . . . . . . . . . . . . . . . . . . 90B4677
Optional Equipment
AuxPander:
The Shure AuxPander auxiliary expander extends the capabilities of a standard mixing console by providing eight additional
auxiliary sends. It is designed ideally for use with multiple personal monitoring systems.
P4M:
The P4M is a highly versatile four–channel, two–bus stereo
mic/line mixer designed to optimize personal (in–ear) monitor
systems in live performance applications.
SPECIFICATIONS
PSM200 System
Modulation
FM ±35 kHz Deviation (Nominal)
RF Carrier Frequency Range
518–865 MHz (country dependent)
Operating Range
100 m (300 ft.) under optimal conditions
Audio Frequency Response
30 Hz to 12 kHz (+/–3 dB); earphone dependent
Total Harmonic Distortion (1 kHz)
<1% typical (Ref. ±35 kHz deviation)
Signal-to-Noise Ratio
80 dB typical (A-weighted)
Operating Temperature
–7° C to +49° C
(+20° F to +120° F)
P2T TransMixer
RF Output Power
30 mW (+15 dBm) typical conducted (country dependent)
Modulation Limiter
Internal peak limiter (>10:1 hard knee compression)
Antenna
1/4 Wavelength, semi-rigid, PCB Mount
Current
170 mA maximum
Dimensions
220 mm x 140 mm x 40 mm (8.6 in. x 5.6 in. x 1.7 in.)
Net Weight
370 g (13 oz.)
12
ENGLISH
P2T Audio Input
XLR/1/4-inch
Connector Type:
P2T Audio Outputs
Passive connection parallel with input.
combo
electronically balanced
Configuration:
Actual Impedance:
1 kΩ
Nominal Input Level:
–25 dBu @ 1/2 volume
(12 o’clock)
Maximum Input Level:
–5 dBu @ 1/2 volume
(12 o’clock)
Pin Assignments:
XLR: 2=hot; 3=cold, 1=ground
1/ : Tip = hot, Ring = cold,
4
Sleeve=ground
Phantom Power Protection?
Yes: Up to 52 Vdc
XLR
Configuration:
electronically balanced
Pin Assignments:
2 = hot ; 3 = cold, 1 = ground
Phantom Power Protection?
Yes: Up to 52 Vdc
Power Requirements
Operating voltage 12-18 Vdc
Supplied with one of the following external power supplies:
Model PS20: 120 VAC, 60 Hz input.
P2R Receiver
RF Sensitivity
–109 dBm typical
Model PS20E, Model PS20UK: 230 VAC, 50/60 Hz input.
Power Requirements
9 V alkaline battery, Duracell type MN1604 recommended
Battery Life
Volume Dependent
Squelch Threshold
–102 dBm typical
Antenna
Attached Whip
1/ -inch
4
Mono
Impedance:
1 MΩ
Maximum Input Level:
LO = +0 dBu
HI = –10 dBu
Frequency Response:
30 Hz to 20 kHz (+/–3 dB);
earphone dependent
Wired (RF Off):
6 hours
Wireless (RF On):
4 hours
Audio Output Connector
1/ inch (3.5 mm)
8
Minimum Load Impedance
8Ω
Net Weight
100 g (3.52 oz.), less battery
Overall Dimensions
122 mm x 73 mm x 32 mm
(4.809 in. x 2.875 in. x 1.251 in.)
Audio Input Connector
Connector Type:
Connector Type:
PSM200 Channel Frequencies
The PSM200 is available in four frequency groups, each coordinated to work in a specific geographic region. You can find the frequency
group for your system printed on the rear panel of the P2T TransMixer. For more information on which frequencies can be used in your area,
call our Applications Group at 847-866-2525, Shure Europe at 49-1731-72140, Shure Asia at 852-2893-4290, or visit the Technical Support
section at www.shure.com.
H2
R8
Q3
S5
(518-554)MHz
North America,
Europe
(800-814)MHz
(748-784)MHz
(842-865)MHz
Europe
France, Australia
England
1
518.750
801.100
749.100
855.275
2
524.875
802.325
754.025
856.175
3
525.625
805.050
756.000
857.625
4
534.375
808.600
765.900
858.200
5
536.875
810.550
772.000
863.075
6
538.500
811.600
775.000
863.625
7
551.000
813.300
778.775
864.425
8
553.250
813.800
781.900
864.850
CHANNEL
Channel A (P2R Only)
Wired Mode (RF Disabled)
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement