NAMCO Time Crisis 4 DX Arcade Game Operators Manual

NAMCO Time Crisis 4 DX Arcade Game Operators Manual

Below you will find brief information for Arcade Game Time Crisis 4 DX. This manual provides guidance on installing, operating, relocating, transporting, maintaining and safely discarding your Time Crisis 4 DX arcade game machine. It also includes information on ensuring player and bystander safety, making full use of the machine’s features, correct operation, and inquiries concerning the machine and repairs.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Time Crisis 4 DX Operators Manual | Manualzz
TIME CRISIS 4 DX
OPERATORS MANUAL
IT
IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY
AT ALL TIMES , AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL
ARE FOLLOWED PRECISELY
Part No. 90500167
NAMCO BANDAI Games Inc.
Issue 2
2
INTRODUCTION
Thank you for purchasing the [TIME CRISIS 4 SD] game machine (hereafter referred to as the
[machine]).
This operation manual describes:
•
How to install, operate, relocate, transport, maintain and discard the
machine safely and properly
•
•
•
•
How to operate the machine correctly and make full use of its features
How to ensure safety of players and bystanders
Inquiries concerning the machine and repairs
For further information about the machine and repairs, please contact your
distributor.
is a copyrighted anti-copying technology created by Sony Corp.
This
mark does not necessarily imply compatibility with other
products bearing the “MAGICGATE” trademark.
is a trademark of Sony Corporation.
est une technique de protection de copyright créée par Sony
Corporation.
ne veut pas nécessairement dire qu’il y a une compatibilté avec
d’autres produits portant la marque commerciale “MAGIGATE”.
est une marque commerciale de Sony Corporation.
3
Contents
OPERATORS MANUAL ............................................................................................................... 1
INTRODUCTION ...........................................................................................................................3
GENERAL SAFETY CONSIDERATIONS .....................................................................................6
ALLGEMEINE SICHERHEITSHINWEISE ....................................................................................8
GENERELLE SIKKERHEDSOVERVEJELSER ......................................................................... 10
CONSIDERACIONES GENERALES DE SEGURIDAD. ............................................................12
CONSIGNES GENERALES DE SECURITE .............................................................................. 14
ΕΞΕΤΑΣΗ ΓΕΝΙΚΗΣ ΑΣΦΑΛΕΙΑΣ ..............................................................................................16
CONSIDERAZIONI GENERALI SULLA SICUREZZA ...............................................................18
VANLIGE SIKKERHETSTILTAK ................................................................................................20
ALGEMENE VEILIGHEIDSOVERWEGINGEN ..........................................................................22
AVISOS DE PERIGO .................................................................................................................. 24
ALLMÄNNA SÄKERHETSBEAKTANDEN .................................................................................26
YLEISET TURVALLISUUNÄKÖKODAT ....................................................................................28
1. SPECIFICATIONS ................................................................................................................30
2. MAIN COMPONENTS ..........................................................................................................31
4. INSTALLATION ....................................................................................................................32
3. MOVING THE MACHINE .....................................................................................................33
4-1
Required Dimension for Access (Doors and Passageways) .........................................36
4-2
Separating the Speaker Box .........................................................................................37
4-3
Fitting the Joint Box ....................................................................................................... 38
4-4
Fitting the Header Assembly .........................................................................................40
4-5
Control Assy .................................................................................................................. 43
4-6
Adjusting the Level Adjusters .......................................................................................44
4-7
Fitting the Pedal Assy ....................................................................................................45
5. OPERATION ......................................................................................................................... 46
5-1
Pre-Service Check ........................................................................................................ 46
5-1-1 Safety Check (before power on) ...............................................................................46
5-1-2 Operation Check (after power On) ...........................................................................47
5-2
How to Play ...................................................................................................................48
6. ADJUSTMENTS ...................................................................................................................50
6-1
Adjustment Switches .....................................................................................................51
6-2
Test Mode ......................................................................................................................52
6-2-1 Coin Options .................................................................................................................54
6-2-2 Game Options ...............................................................................................................55
6-2-3 I/O Test ..........................................................................................................................56
6-2-3-1 I/O PCB Check .........................................................................................................57
6-2-3-2 Gun Initialize ............................................................................................................. 58
6-2-3-3 Switch Test ...............................................................................................................61
6-2-3-4 Solenoid Test ............................................................................................................62
6-2-3-5 LED Test ...................................................................................................................63
6-2-4 Monitor Test ...................................................................................................................64
6-2-5 Sound Test ....................................................................................................................65
6-2-6 Bookkeeping .................................................................................................................66
6-2-7 Others ...........................................................................................................................67
4
7. MAINTENANCE ...................................................................................................................68
7-1
Cleaning ........................................................................................................................70
7-1-1 Cleaning the Gun Assy .............................................................................................70
7-1-2 Cleaning the Front Acrylic Cover ..............................................................................70
7-2
Regular Maintenance ....................................................................................................71
7-2-1 Greasing the Pedal Plunger .....................................................................................71
7-2-2 Checking the Plunger for Wear ................................................................................73
7-3
Removing the Monitor Mask .........................................................................................74
7-4
Replacing the LED Board..............................................................................................76
7-5
Replacing the Game PCB Assy ....................................................................................77
7-6
Replacing the Amp PC Board ......................................................................................78
7-7
Replacing the SIDELED PC Board (Header Assy) ......................................................79
7-8
Replacing the Fluorescent Tube / Starter ......................................................................81
7- 9 Removing the Control Panel .........................................................................................82
7-10 Replacing the SIDELED PC Board ...............................................................................83
7-10-1 (Control Panel) ..........................................................................................................83
7-10-2 (Gun Assy) ................................................................................................................84
7-11 Replacing the NA-JV Board Assy..................................................................................85
7-12 Replacing the CPU Board .............................................................................................86
7-13 Replacing the CROSS PC Board ..................................................................................88
7-14 Replacing the Gun Assy ................................................................................................89
7-15 Replacing the Gun Slides (L & R) .................................................................................90
7-16 Separating The Gun Body .............................................................................................91
7-17 Replacing the Gun Light Receiving Unit .......................................................................92
7-18 Replacing the Gun Solenoid .........................................................................................93
7-19 Replacing the Trigger Microswitch ................................................................................94
7-20 Replacing the Gun Harness ..........................................................................................95
7-21 Replacing the Pedal Micro Switch .................................................................................96
7-22 Replacing the Pedal Plunger.........................................................................................97
8. TROUBLESHOOTING .........................................................................................................98
8-1
Monitor Cabinet Assy ....................................................................................................98
8-2
Header Assy ..................................................................................................................98
8-3
Pedal Assy ....................................................................................................................98
8-4
Control Assy ..................................................................................................................99
8-5
Gun Assy .......................................................................................................................99
9. DISPOSAL .........................................................................................................................100
10. PARTS ................................................................................................................................102
10-1 Monitor Cabinet (L) .....................................................................................................102
10-2 Monitor Cabinet (R) .....................................................................................................104
10-3 Speaker Box Assy (L) ..................................................................................................106
10-4 Speaker Box Assy (R) .................................................................................................107
10-5 Header Assy ................................................................................................................108
10-6 Control Assy ................................................................................................................109
10-7 Game PCB Assy ......................................................................................................... 110
10-8 Coin Tower Assy .......................................................................................................... 112
10-9 Pedal Assy .................................................................................................................. 113
10-10 Gun Tower Assy (L) ..................................................................................................... 114
10-11 Gun tower Assy (R) ..................................................................................................... 116
10-12 Joint Box Assy ............................................................................................................. 118
10-13 Service Bracket Assy .................................................................................................. 119
10-14 Gun Assy .....................................................................................................................120
11. SCHEMATICS ....................................................................................................................122
5
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the
form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for
private use, without permission from NAMCO EUROPE LIMITED.
While the information contained in this manual is given in good faith and was accurate at the time of printing,
NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
This equipment has been manufactured in accordance with European Directives, and has been tested and
complies with the directives 89/336/EEC and 72/23/EEC by the application of EN55014-1, EN55014-2 and
EN60334-2-82 standards and as such bears the CE marking. Any changes or modifications to this equipment
must be in accordance with the European Directives. Any unauthorised changes to this equipment may
contravene such directives.
Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains
born transients, some degradation of performance may occur. However the equipment will recover normal
performance once the source of interference has ceased or been removed.
Following abnormally high surges on the mains supply, the video monitor may need to be manually reset by
turning the equipment OFF and back ON.
If the game processor resets due to an interruption of the mains voltage, any credits established will be lost.
This equipment is not a machine as defined by the machinery directive 89/392/EEC.
SAFETY WARNING
In order to use this equipment safely, be sure to read this Operators Manual carefully before installation,
adjustment or use of this equipment.
Whenever the owner of this equipment entrusts dis-assembly, installation, adjustment or routine maintenance to
another person, the owner should ensure that that person read the appropriate precautions and relevant sections
of this manual before starting work.
In order that no accidents occur when the equipment is in operation, strictly follow the notes on safety as
described below.
This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must
be available to the operating or service personnel at all times.
This equipment is for indoor use only and should only be used for the purpose intended.
Namco Europe Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes
to, or improper use of this equipment.
SAFETY NOTES
The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and it’s
meaning before installing, servicing or making adjustments to this equipment.
WARNING l
Warning denotes a hazard that could result in injury or death. Do not proceed beyond a warning
note until the indicated conditions are fully understood and met.
Caution denotes a hazard that could result in damage to the equipment. Do not proceed beyond
a caution note until the indicated conditions are fully understood and met.
CAUTION
GENERAL SAFETY CONSIDERATIONS
l
Only operate this equipment after checking that it has been installed correctly and in accordance
with this manual.
l
The warning notices must always be kept in good condition and replaced if worn, so that customers
can read them clearly.
l
Installation, service, adjustment or routine maintenance should be carried out by suitably qualified
persons only.
l
For continued protection against fire hazard, replace fuses with the same type and rating. The use of
other fuses or material is prohibited.
l
The power supply inside the monitor will remain hot and have areas of high voltage even though the
equipment has been tuned OFF, and there is the possibility of burns or electric shock. Be careful not
to touch these areas.
l
To prevent possible electric shock due to failure, this equipment MUST be fitted with a securely
connected EARTHED plug.
l
l
6
If at any time the mains lead becomes damaged, it must be replaced immediately.
Do not turn the power switch ON until the equipment has ben installed correctly.
Before connecting the machine to the mains supply, ensure that the equipment is set for the correct voltage
and that the correct fuse are fitted.
NOTES ON INSTALLATION
l
So that customers are not injured by the movement of the
equipment, ensure that there is at least 500mm seperation
between other equipment or walls.
In order to avoid damage to the equipment due to mis-operation,
ensure that the voltage of the mains supply is 230volts AC.
3m40cm or more
50cm or more
50cm or more
50cm or more
In order to prevent possible electric shocks, be sure that the
equipment is connected to the mains with a securely
connected earthed plug.
2m90cm or more
l
Play zone
Note: If the location of this equipment has a polished floor, it is
recommended that rubber pads are fitted under the level adjusters
to prevent the equipment sliding on the floor when in use.
50cm or more
NEVER turn the power to the machine ON until installation has
been completed.
1m or more
l
Aisle
Maintenance zone
Note: In order to gain access to the Power Supply and CPU assemblies,
ensure that the rear of the equipment is seperated from a wall or
other equipment by at least 500mm
MOVING THE EQUIPMENT
l
This equipment is fitted with castors to make it easier to move. Take care when moving the
equipment on an inclined surface.
l
The Header Assembly has a forward centre of gravity, so it is important that at least two people are
used to fit or remove the Header Assembly.
l
The fitting position of the Header Assembly is high, and it is important that a means of reaching the
height safely, without stretching, is available. (e.g. Steps, Step Stool etc.)
l
The overall height of the equipment , with the Header Assembly fitted, is 2340mm. Take care of any
overhead obstructions. (e.g. Light Fittings, Electric Cables etc.
REMOVING AND REPLACING PARTS
l
Adjustments or maintenance on this equipment should be carried out by suitably qualified
personnel only.
l
Do not make any alteration to this equipment without prior approval. Doing so could cause
unforeseeable danger.
l
Only parts specified by Namco Europe Ltd. should be used when replacing parts. (Including
screws)
l
Ensure that the power to the equipment is turned OFF before commencing any maintenance work.
(Trouble shooting, repairs etc.)
l
If performing work not described in this manual, contact your distributor for instructions, as no
responsibility will be accepted for damage or injury.
l
Parts of the Power Supply and Monitor remain hot and carry high voltage even after switching OFF
and could cause burns or electric shock. Take care not to touch these parts accidentally.
l
Make sure that the equipment is switched OFF before connecting or disconnecting any plugs or
connectors.
l
When moving the mains connector from the equipment, or the mains plug from the wall outlet,
always grasp the plug and not the cable.
7
D
Dieses Dokument darf in keiner Weise vervielfältigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf
Datenträger (Suchsysteme), die Weitergabe oder sonstiges Kopieren für den gewerblichen und privaten Gebrauch
sind untersagt und bedürfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED.
Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED
behält sich jedoch das Recht zu Änderungen ohne vorherige Bekanntgabe vor.
Dieses Gerät trägt das CE-Zeichen und wurde gemäß den EU-Richtlinien produziert. Es erfüllt die Richtlinien 89/
336/EEC und 72/23/EEC und Standards EN 55014-1, EN55014-2 und EN60334-2-82 (s. Deckblatt des
Handbuches). Alle Veränderungen an diesem Gerät müssen in Übereinstimmung mit den EU-Richtlinien erfolgen.
Nicht genehmigte Veränderungen an diesem Gerät verstoßen gegen diese Richtlinien.
Extreme äußere Störungen, wie z.B. durch Radiobetrieb, elektrostatische Entladung oder zeitweilige
Netzschwankungen können zu einer Leistungsminderung führen. Sobald diese Faktoren jedoch ausgeschaltet
oder beseitigt wurden, erreicht das Gerät seine normale Leistung.
Achtung! Falls der Spielprozessor auf Grund von Netzunterbrechungen oder Abnahme der Netzspannung
aussetzt, kann es zum Verlust von Spielkrediten kommen.
Dieses Gerät fällt nicht unter die Maschinen-Richtlinie 89/392/EEC
SICHERHEITSHINWEISE
Um einen ordnungsgemäßen Betrieb dieses Gerätes zu gewährleisten, muß vor Aufstellung, Inbetriebnahme und
Gebrauch das Handbuch sorgfältig gelesen werden.
Sobald der Besitzer dieses Gerätes die Demontage, Aufstellung, Inbetriebnahme oder den Service einer anderen
Person überträgt, muß er sicherstellen, daß diese Person vor Arbeitsbeginn die nötigen Sicherheitshinweise und
die dazugehörigen Kapitel des Handbuches liest und versteht.
Um jegliche Unfälle während des Betriebes zu vermeiden, müssen obige Hinweise strikt befolgt werden.
Dieses Handbuch sowie das spezielle Geräte-Handbuch (wenn vorhanden) gehören zum Gerät und müssen dem
Betreiber und Wartungspersonal stets zugänglich sein
Dieses Gerät ist ausschließlich für den gewerblichen Gebrauch in geschlossenen Räumen bestimmt und darf nur
dort betrieben werden.
NAMCO EUROPE Ltd. übernimmt keinerlei Haftung für Unfälle, Verletzungen oder Beschädigungen, die auf nicht
genehmigte Veränderungen oder unsachgemäßen Betrieb des Gerätes zurückzuführen sind.
SICHERHEITSHINWEISE
Folgende Sicherheitsbegriffe werden im gesamten Handbuch benutzt. Machen Sie sich daher bitte vor
Inbetriebnahme, Wartung und Durchführung von Einstellungen am Gerät mit diesen Warnhinweisen vertraut.
WARNUNG
l
WARNUNG bezeichnet eine Gefahrenquelle für Leib und Leben. Erscheint dieser
Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklärungen
vollständig verstanden und befolgt wurden.
VORSICHT
VORSICHT bezeichnet eine Gefahrenquelle für die Beschädigung des Gerätes. Erscheint dieser
Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklärungen
vollständig verstanden und befolgt wurden.
ALLGEMEINE SICHERHEITSHINWEISE
l
Das Gerät darf nur betrieben werden, nachdem es vorschriftsmäßig und in Übereinstimmung mit dem
Handbuch aufgestellt wurde.
l
Die Warnschilder müssen in gutem Zustand sein und ersetzt werden, wenn sie nicht mehr gut lesbar
sind.
l
Bei Auftreten eines Fehlers oder Problems muß das Gerät sofort abgeschaltet werden und darf erst
nach fachgerechter Behebung des Fehlers wieder in Betrieb genommen werden.
l
Aufstellung, Service, Einstellungen und Wartung dürfen nur von dafür qualifiziertem Fachpersonal
durchgeführt werden.
l
Zur Vermeidung von Feuer, defekte Sicherungen nur durch vorgeschriebene Sicherungen ersetzen.
Die Verwendung von andersartigen Sicherungen oder unterschiedlichem Material ist untersagt.
l
Das Netzteil im Monitor bleibt nach Ausschalten des Gerätes noch heiß und führt weiterhin
Hochspannung. Daher besteht die Gefahr von Verbrennungen und Elektroschlägen. Diese Bereiche
dürfen nicht berührt werden.
l
Zur Vermeidung von Elektroschlägen muß dieses Gerät mit einem ordnungsgemäß geerdeten
Netzstecker versehen sein.
l
l
Bei Beschädigungen des Netzteiles muß dieses umgehend ersetzt werden.
8
Gerät erst nach abgeschlossener Aufstellung einschalten.
Vor Einstecken des Netzsteckers bitte sicherstellen, daß Netzspannung und Gerätespannung
übereinstimmen, und die vorgeschriebenen Sicherungen verwendet wurden.
HINWEISE ZUR AUFSTELLUNG
l
Um zu vermeiden, daß Kunden durch die Gerätebewegungen
verletzt werden, muß ein Sicherheitsabstand zu anderen Geräten
und Wänden von mindestens 50cm eingehalten werden.
Zur Vermeidung von Beschädigungen durch Fehlbetrieb am Gerät
sicherstellen, daß die Netzspannung 230 Volt beträgt.
3m40cm or more
50cm or more
50cm or more
Hinweis: Ist das Gerät für einen Aufstellplatz mit glattem Fußboden
bestimmt, müssen die Standbeine mit Gummiplättchen unterlegt
werden, damit das Gerät fest steht und nicht auf dem Boden
hin- und herrutscht.
50cm or more
Zur Vermeidung von Elektroschlägen muß das Gerät mit einem
ordnungsgemäß geerdetem Netzstecker an die
Stromversorgung angeschlossen werden.
2m90cm or more
l
Play zone
50cm or more
NIEMALS das Gerät einschalten bevor die Aufstellung völlig
abgeschlossen ist.
1m or more
l
Aisle
Maintenance zone
Hinweis: Zu Reparaturzwecken am Netzteil und den CPU-Komponenten
muß die Rückseite des Gerätes mindestens 50cm von anderen
Geräten und der Wand entfernt sein.
l
Zum leichteren Transport ist das Gerät mit Rollen ausgerüstet. Daher besondere Vorsicht auf
abschüssigem Boden
l
Der Schwerpunkt des Aufsatzes liegt sehr weit vorn. Daher werden für den Ab- und Aufbau des
Aufsatzes mindestens 2 Personen benötigt.
l
Der Aufsatz wird in großer Höhe montiert. Daher muß aus Sicherheitsgründen eine Steighilfe,
wie z. B. eine Leiter, ein Tritt oder ähnliches, verwendet werden.
l
Die Gesamthöhe de Gerätes beträgt 2.34m. Daher Vorsicht bei tiefer hängenden
Beleuchtungskörpern.
AUS- UND EINBAU VON KOMPONENTEN UND TEILEN
l
Aufstellung, Service, Einstellung und Wartung dürfen nur von dafür qualifiziertem Fachpersonal
durchgeführt werden.
l
Es dürfen keierlei Veränderungen ohne vorherige Genehmigung am Gerät vorgenommen
werden. Zuwiderhandlungen stellen eine Gefahrenquelle dar.
l
Für die Repartur dürfen nur Originalersatzteile (incl. Schrauben) von NAMCO EUROPE LTD.
verwendet werden.
l
Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der Netzstecker
gezogen werden.
l
Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muß vorher der Händler zu
Rate gezogen werden, da sonst keinerlei Haftung bei Beschädigungen und Verletzungen
übernommen wird.
l
Teile des Netzteiles und Bilschirmes bleiben nach Abschalten noch heiß und führen
Hochspannung. Dies kann zu Verbrennungen oder einem Elektroschlag führen. Diese Teile
dürfen nich berührt werden.
l
Vor der Montage oder dem Entfernen von Steckverbindungen und Steckern muß das Gerät
ausgeschaltet werden.
l
Bei Ziehen des Gerätesteckers oder des Netzsteckers aus der Wandsteckdose stets den
Stecker greifen und nicht das Kabel.
9

Denne udgivelse må ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i
form af indspilning, den må heller ikke lagres i et eftersøgningssystem transmitteres eller kopieres til nogen form for
offentlig benyttelse uden tilladelse fra Namco Europe Limited.
Da informationerne i denne manual er givet med god tro og var korrekt på udskivningstidspunktet,
forbeholder Namco Europe Limited sig retten til, at foretage ændringer og forandringer uden varsel.
Denne maskine er frernstillet i overensstemmelse med Det Europæiske fællesskabs direktiver og er blevet testet og
fuldendt med direktiverne 89/336/EEC og 72/23/EEC standarder (se manualens forside) og som sådan bærer CE
mærket. Enhver form for ændring eller modiflkation af denne maskine skal være i overensstemmelse med Det
Europæiske fællesskabs direktiver.
I tilfælde af forbigående ekstreme eksterne forstyrrelser, så som radio udsendelser, elektronisk afgivelse eller
forstyrrelser på ledningsnettet, kan nedbrydning forekomme. Maskinen vil dog køre normalt så snart forstyrrelsen
ophører eller bliver fjernet.
Bemærk:- Hvis spilleprocessoren resetter p.g.a. en forstyrrelse eller reduktion af hovedstrømmen kan de
etabledrede kreditter gå tabt.
Dette spil er ikke en maskine defineret af maskin direktivet 89/392/EEC -
SIKKERHEDS ADVARSEL
For at betjene denne maskine sikkert, læs da denne brugemanual grundigt før installation, justering eller brug af
maskinen.
Når som helst ejeren af denne maskine overlader demontering, installation, justeringer eller daglig vedligehold til en
anden person, skal ejeren sikre sig at denne person læser de sikkerhedsregler og relevante punkter i denne manual
før arbejdet begynder.
For at undgå ulykker nor maskinen er i gang, følg nøje de sikkerhedsregler der er beskrevet herunder.
Denne manual sammen med installations manualen er en uløselig del af udstyret og skal altid være til
råidighed for det arbejdende og servicerende personale.
Denne rnaskine er kun til indendørs brug og bør kun bruges til det beregnede formål.
Namco Ltd. bærer intet ansvar for ulykker eller skader som er et resultat af uautoriserede ændringer eller
fejlagtig brug af denne rnaskine.
SIKKERHEDSREGLER
De følgende sikkerhedsregler er brugt helt igennem denne manual. Gør dig bekendt med hver enkelt af dem
og meningen heraf før installering, servicering eller justering af denne maskine.
ADVARSEL l
Advarsel betegner en episode der kan resultere i skader eller død. Begiv dig ikke
forbi et advarselsskilt før de indikerede betingelser er fuldstændig forstået.
FORSIGTIG
Forslgtig betegner en episode der kan resultere i ødelæggelse af maskinen. Begiv dig
ikke forbi et advarselsskit før de indikerede betingeser er fuldstændig forstået.
GENERELLE SIKKERHEDSOVERVEJELSER
l
Betjen kun maskinen efter at have tjekket, at den er korrekt installeret og er i overensstemmelse med
manualen.
l
Advarselsskiltene skal altid være i god stand og erstattes hvis de er slidt, så kunden tydeligt kan læse
dem.
l
Hvis der er en fejl eller et problem med maskinen skal betjening straks stoppes, og problemet
afhjælpes før yderligere brug.
l
l
Installations service, justeringer eller daglig vedligehold bør kun udføres af en kvalificeret person.
l
Strømforsyningen inde 1 monitoren vil forblive varin og have områder med høj spænding selvom
maskinen har været slukket og der er fare for brandskader eller elektrisk stød. Pas på med at røre
disse områder.
l
l
l
l
For at undgå elektrisk stød p.g.a. en fejl skal denne maskine være forbundet med et sikkert jordstik.
10
For fortsat beskyttelse mod brandfare, sikres at hoved sikringerne kun erstattes med samme type
kapacitet. Brug af anden kapacitet eller materiale er forbudt.
Hvis hoved ledningerne på noget tidspunkt bliver beskadiget skal de strakt erstattes.
Tænd ikke for strømmen før maskinen er korrekt installeret.
Før tilslutning af maskinen til hovedstrømmen sikres, at maskinen er indstillet til den rette spænding.
PUNKTER OM INSTALLATION
l
For at kunder ikke kommer til skade ved spillets bevægelser sikres,
at der er mindst 50cm afstand til andre maskiner og vægge.
For at undgå skader på maskinen p.g.a. fejlbetjening sikres, at
spændingen på hovedstrømmen er 230 volt AC.
BEMÆRK :
BEMÆRK :
3m40cm or more
50cm or more
50cm or more
Hvis denne maskine placeres på et poleret gulv, anbefales
det at ligge gummimåtter under justeringsfødderne for at
undgå at maskinen glider på gulvet.
50cm or more
For at undgå mulige elektriske stød sikres, at maskinen er forbundet
til hovedstrømmen med sikkert monterede jordstik.
2m90cm or more
l
50cm or more
Tænd aldrig for strømmen til maskinen før installering er
fuldført.
Play zone
1m or more
l
Aisle
Maintenance zone
For at få adgang til strømforsyningen og CPU justeringer
sikres, at bagsiden af hoved kabinettet står adskilt fra andre
maskiner eller væggen med mindst 50cm.
l
Maskinen er smurt med olie for at gøre den lettere bevægelig. Pas på når maskinen flyttes på
en skrå overflade.
l
Hoved sektionens forreste center er meget tung, det er derfor vigtigt, at mindst 2 personer
benyttes til at montere el. flytte hoved sektionen.
l
Monterins højden af hoved sektionen er meget høj og det er vigtigt, at have hjælpemidler til at
nå sikkert uden at skulle strække sig. (fek.s. trapper, trappestole el. lign.).
l
Den fulde højde af hoved sektionen er 2.34m. Pas på øvre forhindringer f.eks. lys inventar
AT FJERNE OG UDSKIFTE SEKTIONER OG DELE.
l
l
l
Justeringer eller vedligehold af denne maskine bør kun udføres af kvalificeret personale.
l
Sørg for, at strømmen til maskinen er slukket før der foretages nogen form for arbejde
(fejlfinding, reparation etc.)
l
Hvis der foretages arbejde der ikke er beskrevet i denne manual, kontakt da din leverandør for
at få kyndig vejledning, da intet ansvar vil blive accepteret ved skader.
l
Dele af strømforsyningen og monitoren forbliver varme eller bærer høj spænding selv efter
maskinen er slukket, det kan føre til forbrændinger eller elektriske stød. Pas på ikke at røre
disse dele ved et uheld.
l
l
Læg mærke til at maskinen er slukket før samlinger eller stik tages ud eller sættes i.
Skift ikke noget på maskinen uden godkendelse, det kan føre til uforudset fare.
Der bør kun bruges dele specificeret af Namco Europe Limited når der skiftes eller repareres
dele (inklusiv skruer).
Når hovedsamlingen fjernes fra maskinen eller hovedstikket fjernes fra væggen, tag da altid ved
stikket, ikke ledningen.
11

No se permite la reproducción total ni parcial de esta publicación por ningún medio mecánico, fotográfico o
electrónico, grabaciones fonográficas, ni su almacenamiento informático, su transmisión o su copia, ya sea para
uso público o privado, sin permiso de NAMCO EUROPE LIMITED.
Si bien la información contenida en este manual se da de buena fe y es correcta en el momento de su impresión,
NAMCO EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.
Esta máquina ha sido fabricada según las directrices de la Comunidad Europea, ha sido probada, y se ajusta a las
directrices 89/336/EEC y 72/23/EEC, mediante la aplicación de los estándares EN55014-1, EN55014-2 y
EN60334-2-82 (véase cubierta del manual) y por ende lleva el sello de la C.E. Cualquier cambio o modificación
que se haga a esta máquina ha de ajustarse a las directrices de la Comunidad Europea. Cualquier cambio no
autorizado hecho al producto pudiera contravenir estas directrices.
Bajo ciertas condiciones de extrema interferencia externa, p. ej. transmisiones de radio, descargas electrostáticas
u oscilaciones de la red eléctrica puede tener lugar un descenso del rendimiento. No obstante, la máquina
recuperará su rendimiento normal una vez que la fuente de interferencias sea retirada o cese de producirlas.
Nota: Si el procesador de juegos se reinicializa a causa de caídas o interrupciones en la alimentación eléctrica, se
perderán todos los créditos.
Este juego no se ajusta a la definición de máquina de la Normativa de Maquinaria 89/392/EEC
AVISOS DE SEGURIDAD.
Para utilizar esta máquina con seguridad, lea cuidadosamente este Manual de Operador antes de proceder a la
instalación, ajuste o uso de esta máquina.
Cada vez que el propietario de esta máquina confíe a terceros su desmontaje, instalación, ajuste o mantenimiento
rutinario deberá asegurarse de que tales personas lean las precauciones adecuadas y las secciones relevantes de
este manual antes de comenzar su trabajo.
Para que no ocurra accidente alguno mientras la máquina se encuentre en funcionamiento, siga estrictamente las
notas de seguridad tal como más adelante se describen.
Este manual, junto con el Manual de Instalación (cuando proceda), forma parte integral del equipo y debe estar a
disposición del personal de mantenimiento y operación en todo momento.
Esta máquina es únicamente para ser usada en interiores, y sólo debe usarse para aquello para lo que ha sido
creada.
Namco Ltd. queda exenta de cualquier responsabilidad por accidentes, heridas o daños causados por cambios no
autorizados o uso indebido de esta máquina.
NOTAS DE SEGURIDAD.
En este manual se usan las notas siguientes. Familiarícese con cada una de ellas y su significado antes de
instalar, revisar, o hacer ajustes en esta máquina.
AVISO.
l
PRECAUCIÓN.
Aviso señala un riesgo que puede ocasionar lesiones o la muerte. Tras ver esta
nota, no continúe hasta entender completamente y cumplir las condiciones
exigidas.
Precaución señala un riesgo que puede ocasionar daños a la máquina. Tras ver
CONSIDERACIONES GENERALES DE SEGURIDAD.
l
Opere sólo con esta máquina tras comprobar que ha sido instalada correctamente y de acuerdo con
este manual.
l
Las notas de aviso deben mantenerse siempre en buen estado y reemplazarse si estuvieran
desgastadas para que los usuarios puedan leerlas con claridad.
l
Si hubiera algún error o problema con la máquina, debe interrumpirse su operación inmediatamente, y
subsanar el problema antes de volver a usarla.
l
Las revisiones de instalación, los ajustes, y el mantenimiento rutinario deberán llevarse a cabo sólo por
personal cualificado.
l
Para asegurar una continua protección contra riesgo de incendios, asegúrese de que los fusibles
eléctricos sean reemplazados solamente por otros del mismo tipo y especificaciones. El uso de otros
fusibles o material está prohibido.
l
La fuente de alimentación del monitor se mantiene caliente, y tiene zonas de alto voltaje incluso
cuando la máquina ha sido desconectada, existiendo el riesgo de quemaduras y descargas eléctricas.
Tenga cuidado de no tocar estas zonas.
l
Para evitar posibles descargas eléctricas por cortes, esta máquina debe estar provista de un enchufe
debidamente conectado, con TOMA DE TIERRA.
l
l
.
Si en cualquier momento el cable de alimentación se dañara, deberá ser reemplazado inmediatamente.
12
No encienda el interruptor de la máquina hasta que ésta haya sido correctamente instalada.
Antes de enchufar la máquina a la red eléctrica, asegúrese de que la máquina está preparada para el voltaje
correcto, y de que se usan los fusibles adecuados.
NOTAS DE INSTALACIÓN.
l
Para que los usuarios no sufran lesiones debido al movimiento del
juego, asegúrese de que hay al menos 500 mm de separación entre
éste y otras máquinas o las paredes.
Para evitar daños a la máquina causados por operación incorrecta,
asegúrese de que el voltaje de la red es de 230 voltios, corriente
alterna.
3m40cm or more
50cm or more
50cm or more
Notas : Si el lugar donde se instalará la máquina tiene un piso pulido, se
recomienda colocar tacos de goma bajo los ajustadores de nivel
para evitar que la máquina se deslice por el suelo.
50cm or more
Para evitar posibles descargas eléctricas, asegúrese de que la
máquina está conectada a la red con un enchufe provisto de
toma de tierra.
2m90cm or more
l
50cm or more
JAMÁS ENCIENDA la máquina antes de haber completado la
instalación.
Play zone
1m or more
l
Aisle
Maintenance zone
Notas : Para acceder a las unidades de Fuente de Alimentación y CPU,
asegúrese de que la parte trasera del mueble principal está
separada de muros u otras máquinas al menos 500 mm.
l
El juego tiene ruedecitas para hacer más fácil su traslado. Tenga cuidado al mover la máquina
en una superficie inclinada.
l
La Unidad de Igualación tiene el centro de gravedad desplazado hacia adelante. Es importante
que su montaje y desmontaje se haga por al menos dos personas.
l
La posición de la Unidad de Igualación es bastante alta, y es importante que haya un medio de
alcanzar su altura con seguridad, sin estirarse (p. ej. una escalera, un taburete, etc.)
l
La altura total de la Unidad principal es de 2340mm. Tenga cuidado de que no haya obstáculos
p. ej. luces.
RETIRAR Y REEMPLAZAR PARTES Y UNIDADES.
l
Las revisiones de instalación, los ajustes, y el mantenimiento rutinario deberán llevarse a cabo sólo
por personal cualificado.
l
No realice alteraciones en esta máquina sin aprobación previa. De hacerlo así, pueden causar
peligros imprevisibles.
l
Sólo deben usarse las partes especificadas por Namco Europe Ltd. para reparaciones o reemplazos
(incluidos los tornillos).
l
Asegúrese de que la máquina está desconectada antes de comenzar cualquier trabajo de
mantenimiento (reparaciones, resolución de problemas, etc.)
l
Al realizar trabajos no descritos en este manual, póngase en contacto con su distribuidor para recibir
instrucciones. Se declina cualquier responsabilidad por daños o lesiones.
l
Hay partes de la fuente de alimentación y del monitor que se mantienen calientes o almacenan alto
voltaje incluso tras desconectar la máquina, y pueden producir quemaduras o descargas eléctricas.
Tenga cuidado de no tocar accidentalmente estas partes.
l
Asegúrese de que la máquina está apagada antes de conectar o desconectar cualquier enchufe o
conector.
l
Al retirar el conector principal de la máquina, o la clavija de alimentación del enchufe de la red, agarre
siempre la clavija y no el cable.
13

Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou
électronique, ni par un moyen d’enregistement phonographique. Ces informations ne seront ni stockées grâce à
un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans
l’autorisation de NAMCO EUROPE LIMITED.
Malgré le fait que les informations contenues dans ce manuel soient données de bonne foi et étaient actualisées
au moment de leur impression, NAMCO EUROPE LIMITED se réserve le droit de procéder à des changements ou
à des modifications sans avis préliminaire.
Ce jeu a été fabriqué en respect des normes de la Communauté Européenne, après avoir été testé il répond aux
normes 89/336/EEC et 72/23/EEC, en application des standards EN55014-1, EN55014-2 et EN60334-2-82 (voir la
couverture du manuel), et comme tel il comporte l’autocollant de conformité avec les normes de la Communauté
Européenne. Tout changement non autorisé sur ce produit pourrait contrevenir à ces normes.
Sous certaines conditions extrêmes d’interférence exteme, par example des transmissions radio, des décharges
électrostatiques ou bien de interférences passagères sur le réseau, certaines dégradations ou anomalies peuvent
se produire. Le jeu retrouvera cependant son état normal de fonctionnement lorsque la cause de ces anomalies
aura cessé ou se trouvera déplacée.
Note:Si le processeur du jeu se reprogramme suite à une interruption ou une réduction de l’alimentation, les crédits qu’il
aurait pu contenir peuvent se trouver perdus.
Ce jeu n’est pas une machine, telle que définie par la norme sur les machines 89/392/EEC
MESURES DE SECURITE
Afin d’utiliser ce jeu en toute sécurité, bien lire ce manuel d’utilisation avant de procéder à son installation, son
réglage ou son exploitation.
Si le propriétaire de ce jeu en confie la démontage, l’installation, le réglage ou la maintenance habituelle à une
autre personne, il devra s’assurer que cette personne ait lu les conseils d’utilisation et les passages du manuel se
rapportant à ce thème, avant qu’elle ne commence son travail.
Afin d’éviter tout accident pendant la durée d’exploitation de ce jeu, se conformer strictment aux conseils de
sécurité décrits à la suite.
Ce manuel ainsi que le manuel d’installation du jeu (là où nécessaire) font partie des éléments nécessaires à
l’installation de la machine et doivent être mis à la disposition de l’utilisateur et du personnel de maintenance à
tout moment.
Ce jeu est uniquement destiné à un usage intérieur et devra être utilisé comme tel.
Namco Ltd. ne sera aucunement tenu responsable en cas d’accidents, de blessure ou de dommage quelconque
résultant de modifications non autorisées ou d’usage impropre du jeu.
REMARQUES SUR LA SECURITE
Les termes de sécurité détaillés à la suite seront utilisés tout au long de la lecture de ce manuel. Il convient de
vous familiariser aves chacun de ces termes ainsi que leur signification avant de procéder à l’installation, à la
maintenace ou au réglage du jeu.
AVERTISSEMENT
ATTENTION
l Ce terme annonce un danger qui pourrait éventuellement avoir des
conséquences dommageables ou mortelles. Ne pas passer oûtre ce signal jusqu’à
ce que les conditions indiquées soient entiérement comprises et effectuées.
Ce terme indique qu’un danger menace la machine. Ne pas passer oûtre ce signal
jusqu’à ce que les conditions indiquées soient entiérement comprises et effectuées.
CONSIGNES GENERALES DE SECURITE
l
Allumer l’appareil seulement après avoir vérifié qu’il a été correctement installé, et que les
instructions du manuel ont été respectées.
l
Les notes de mise en garde doivent constamment demeurer en bon état et être remplacées en cas de
disparition, afin que le client puisse les lire clairement.
l
S’il y una erreur ou un problème avec la machine, l’utilisation doit être immédiatement interrompue et
le problème résolu avant toute nouvelle utilisation.
l
L’installation, le service, le réglage, ou la maintenance doivent être effectués uniquement par les
personnes qualifiées.
l
Afin d’éviter un éventuel incendie, s’assurer que les fusibles soient remplacés par le même type de
fusibles et au bon voltage. L’utilisation d’autres sortes de fusibles ou autres matériels est interdite.
l
L’alimentation à l’intérieur du moniteur reste chaude et comporte des zones de haute tension même
si la machine est éteinte. Il existe donc un risque de brúlure ou d’électrocution. Attention à ne pas
toucher ces endroits.
l
Pour prévenir une éventuelle électrocution due à un défaut matériel, ce jeu DOIT être muni d’une prise
de TERRE connectée en toute sécurité
l
l
Si à tout moment les fils électriques sont endommagés, il faut les remplacer immédiatment
14
Ne pas mettre le jeu en mode de fonctionnement avant qu’il n’ait été correctement installé.
Avant de connecter la machine au réseau, s’assurer que la machine est installée sous la bonne tension et
que les fusibles correspondent.
NOTES D’INSTALLATION
l
Afin que les clients ne soient pas blessés par les
mouvements du jeu, s’assurer qu’il existe au moins 500
mm de séparation aves les autres jeux ou les murs.
Afin d’éviter que la machine ne soit abimée suite à une
mauvaise opération, s’assurer que la tension sur le réseau
principal soit de 230 volts AC.
3m40cm or more
50cm or more
50cm or more
50cm or more
Afin de prévenir une éventuelle électrocution, s’assurer
que la machine est connectée au réseau avec une prise de
terre reliée selon les normes de sécurité.
2m90cm or more
l
Play zone
Note: Si l’endroit où doit être installée la machine à un sol pôli, il est
recommandé de poser des tampons feutrés sous les vérins
pour éviter que le jeu ne glisse sur le sol
50cm or more
NE JAMAIS mettre le jeu en marche avant que l’installation
ne soit complétement effectuée.
1m or more
l
Aisle
Maintenance zone
Note: Afin de facilité l’accès aux CPU at à l’alimentation, s’assurer
qu’il y a un espace d’au moins 500 mm entre l’arrière du
meuble et le mur ou tout autre jeu.
l
Le jeu est foumi avec des roulettes pour une meilleure mobilité. Prendre garde quand la
machine est déplacée sur une surface inclinée.
l
Le centre de gravité de la partie supérieure du jeu est situé sur l’avant, il est donc
indispensable que deux personnes au moins soient employées pour installer ou déplacer la
partie supérieure.
l
L’installation de la partie supérieure du jeu s’effectue en hauteur, il est donc important d’utiliser
un élevateur quelconque pour en effectuer le montage.
l
La hauteur totale de l’assemblage principal est de 2340 mm, prendre garde aux encombrements
de la partie supérieure (ex : illuminations du bandeau).
DEPLACER ET REMPLACER LES UNITES ET LES PIECES DETACHEES.
l
L’installation, le service, le réglage, ou la maintenance doivent être effectués uniquement par
les personnes qualifiées.
l
Ne pas apporter de modifications sur cette machine sans autorisation préalable, faute de quoi
cela pourrait entraîner un danger.
l
Seules les pièces détachées Namco Europe Ltd. doivent être utilsées pour le remplacement ou
la réparation de pièces (y compris les vis)
l
S’assurer que l’interrupteur soit sor OFF avant de commencer tout travail de maintenance
(localisation d’une panne, rèparations, etc.)
l
Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter
votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de
blessure.
l
Les pièces de l’alimentation et du moniteur restent chaudes, à tension élévée même lorsque la
machine est hors tension, elle pourrait occasionner des brûlures ou des électrocutions.
Attention de ne pas toucher ces endroits accidentellement.
l
S’assurer que la machine soit hors tension avant de brancher ou débrancher toute prise ou
connecteur.
l
Lorsque l’on manipule la prise au réseau de la machine, ou lorsque les prises principales
doivent être débranchées, saisir toujours la prise, et non le câble.
15
ও
Κανένα μέρος αυτής της έκδοσης δεν μπορεί να αναπαραχθεί με οποιοδήποτε μηχανικ ,φωτογραφικ ή ηλεκτρονικ
μέσο , ή με μορφή φωνητικής ηχογράφησης και ούτε να αποθηκευτεί με επανορθωτικ σύστημα , να μεταδοθεί ή να
αντιγραφεί για δημσια ή ιδιωτική χρήση , χωρίς την άδεια της NAMCO EUROPE LIMITED.
Καθώς αυτές οι πληροφορίες σε αυτ το εγχειρίδιο έχουν δοθεί με καλή πίστη και ακριβώς την ώρα της τύπωσης , η
εταιρεία
NAMCO EUROPE LIMITED κρατάει το δικαίωμα να κάνει οποιεσδήποτε αλλαγές χωρίς ειδοποίηση.
Τα μηχανήματα έχουν κατασκευαστεί σύμφωνα με τους ρους της Ευρωπαϊκής Κοιντητας , και έχουν ελεγχθεί σύμφωνα
με τους νμους
89/336/ΕΟΚ και 72/23/ΕΟΚ με την αίτηση των ΕΝ55014-1 , ΕΝ55014-2 και ΕΝ60334-2-82 στάνταρτς (δες μπροστά στο
εγχειρίδιο) και λα έχουν το CE σήμα . Οποιαδήποτε αλλαγή ή μετατροπή σε αυτ το μηχάνημα πρέπει να είναι σύμφωνα
με τους ρους της Ευρωπαϊκής Κοιντητας. Οποιεσδήποτε αλλαγές χωρίς άδεια σε αυτ το προϊν μπορεί να παραβεί
αυτούς τους ρους.
Σε κάποιες περιπτώσεις υπερβολικής εξωτερικής παρεμβολής ,π.χ. ραδιοφωνικές μεταδσεις, ηλεκτροστατικές
μεταβολές ή παροδικές εμβολές , μπορεί να παρουσιαστούν κάποιες αθλιτητες στην παρουσίαση. Πάντως το μηχάνημα
θα επανέλθει στην φυσιολογική παρουσίαση εφ σον η πηγή της παρεμβολής σταματήσει ή απομακρυνθεί.
Σημείωση : Εάν γίνει reset στον processor του μηχανήματος κατά τη διάρκεια της κύριας παροχής , πντοι που έχουν
κερδηθεί μπορεί να χαθούν.
Αυτ το παιχνίδι δεν είναι μηχάνημα πως προσδιορίζεται απ τους ρους Μηχανημάτων 89/392/ΕΟΚ .
OΔΗΓΙΕΣ ΑΣΦΑΛΕΙΑΣ
Για την ασφαλή χρήση του μηχανήματος , πρέπει να διαβάσεις το εγχειρίδιο χρήσης προσεκτικά πριν την εγκατάσταση
,τοποθέτηση ή χρήση του μηχανήματος.
Οποτεδήποτε ο ιδιοκτήτης αυτού του μηχανήματος ζητάει απ κάποιο πρσωπο να εγκαταστήσει , να κάνει
οποιαδήποτε αλλαγή ή έλεγχο ρουτίνας στο μηχάνημα , πρέπει να είναι σίγουρος τι έχει διαβάσει τις οδηγίες αυτού
του εγχειριδίου πριν να αρχίσει να δουλεύει .
Προς αποφυγήν οποιουδήποτε ατυχήματος κατά την λειτουργία του μηχανήματος , αυστηρώς ακολουθούνται οι
οδηγίες ασφάλειας πως δίνονται παρακάτω .
Αυτ το εγχειρίδιο σε συνδυασμ με το εγχειρίδιο εγκατάστασης (που διατίθεται) αποτελεί ένα ολοκληρωμένο
μέρος των παροχών και πρέπει να είναι διαθέσιμο για την λειτουργία και το service οποιαδήποτε στιγμή.
Αυτ το μηχάνημα είναι για χρήση μνο σε εσωτερικ χώρο και θα πρέπει να χρησιμοποιείται μνο για τους λγους
για τους οποίους κατασκευάστηκε.
Η εταιρεία NAMCO Ltd δεν φέρει καμία ευθύνη για ατυχήματα , πληγές ή καταστροφές που μπορεί να προκληθούν
απ αλλαγές χωρίς άδεια σε ή εισαγωγείς αυτού του μηχανήματος.
ΣΗΜΕΙΩΣΕΙΣ ΑΣΦΑΛΕΙΑΣ
Οι ακλουθες σημειώσεις ασφάλειας χρησιμοποιούνται μέσω αυτού του εγχειριδίου . Διάβασε αυτές προσεκτικά
για να γίνει κατανοητ το νημά τους πριν την εγκατάσταση , σέρβις ή οποιαδήποτε αλλαγή γίνει στο μηχάνημα.
ΠΡOΕΙΔOΠOΙΗΣΗ
l
ΠΡOΣOΧΗ
Η προειδοποίηση αφορά κίνδυνο ο οποίος μπορεί να είναι λγος θανάτου . Να μην
προχωρήσεις σε οποιαδήποτε κίνηση μέχρι αυτοί οι ροι γίνουν κατανοητοί.
Η προσοχή αφορά κίνδυνο ο οποίος μπορεί να προκαλέσει πρβλημα στο μηχάνημα .
Να μην προχωρήσεις σε οποιαδήποτε κίνηση μέχρι αυτοί οι ροι γίνουν κατανοητοί.
ΕΞΕΤΑΣΗ ΓΕΝΙΚΗΣ ΑΣΦΑΛΕΙΑΣ
l
l
l
l
l
l
l
l
l
16
Αφού έχει κατανοηθεί αυτ το εγχειρίδιο , μνο ττε να λειτουργήσει το μηχάνημα ή να γίνει έλεγχος εφ σον
έχει γίνει η εγκατάσταση.
Οι προειδοποιήσεις πρέπει να μένουν καθαρές και σε καλή κατάσταση ώστε ο πελάτης να τις διαβάζει καθαρά.
Εάν υπάρχει λάθος ή πρβλημα με το μηχάνημα , η λειτουργία πρέπει να σταματάει αμέσως και να διορθώνεται το
λάθος πριν οποιαδήποτε άλλη χρήση.
Εγκατάσταση , μετατροπή ή έλεγχος ρουτίνας μπορεί να γίνεται μνο απ εξουσιοδοτημένα άτομα .
Για συνεχή προστασία απ φωτιά , πρέπει οι ασφάλειες να αντικαθιστούνται με ίδιου τύπου .Η χρήση άλλων
ασφαλειών ή αντικειμένων απαγορεύεται.
Το τροφοδοτικ στο εσωτερικ του μηχανήματος θα παραμείνει ζεστ και υπάρχουν περιοχές με υψηλή τάση
παρ’λο που το μηχάνημα δεν δουλεύει , και υπάρχει η πιθαντητα ηλεκτρικού σοκ . Προσοχή να μην ακουμπήσεις
αυτές τις περιοχές.
Για την αποφυγή ηλεκτρικών σοκ λγο βλάβης , το μηχάνημα ΠΡΕΠΕΙ να έχει πρώτα ενωθεί με γείωση.
Εάν κάποια στιγμή καταστραφεί η κύρια παροχή , πρέπει να αντικατασταθεί αμέσως.
Να μην ανάψει το μηχάνημα (switch ON) μέχρι να έχει εγκατασταθεί σωστά και πλήρως.
Πριν την παροχή ρεύματος στο μηχάνημα , να είσαι σίγουρος τι τα voltage και λες οι ασφάλειες είναι σωστά
ενωμένα και τοποθετημένα.
ΣΗΜΕΙΩΣΕΙΣ ΓΙΑ ΤΗΝ ΕΓΚΑΤΑΣΤΑΣΗ
l
Για την αποφυγή κινδύνου σε κάποιον παίκτη , πρέπει το
μηχάνημα να έχει απσταση τουλάχιστον 500mm απ άλλο
μηχάνημα ή τοίχο.
Για την αποφυγή βλάβης στο μηχάνημα λγο λάθος
λειτουργίας , πρέπει η παροχή να είναι 230volt AC..
ΣΗΜΕΙΩΣΗ: Εάν το πάτωμα στο οποίο είναι τοποθετημένο το
μηχάνημα γλυστράει,είναι καλ να μπει ένα κομμάτι
μοκέτας για αποφυγή μετακίνησης του μηχανήματος εν
ώρα λειτουργίας του.
3m40cm or more
50cm or more
50cm or more
50cm or more
Για την αποφυγή ηλεκτρικών σοκ πρέπει το μηχάνημα να έχει
γειωθεί.
2m90cm or more
l
Play zone
50cm or more
ΠΟΤΕ να μην ανάβει το μηχάνημα εάν δεν έχει ολοκληρωθεί η
εγκατάσταση.
1m or more
l
Aisle
Maintenance zone
ΣΗΜΕΙΩΣΗ: Για την εύκολη πρσβαση στην κυρίως παροχή ή το
CPU πρέπει η πίσω πρτα του μηχανήματος να απέχει
τουλάχιστον 500mm απ τον τοίχο ή άλλο μηχάνημα.
l
l
Το μηχάνημα είναι εφοδιασμένο με καρούλια για την εύκολη μετακίνησή του.
l
Η κεφαλή (καπάκι) του μηχανήματος είναι πολύ ψηλ και γιαυτ χρειάζεται προσοχή στην
τοποθέτησή του , να μην χτυπήσει ή καταστραφεί.
l
Το συνολικ ύψος της κεφαλής είναι 2340mm . Φρντισε να μην χτυπήσει σε λάμπες κ.λ.π.
Το επάνω μέρος του μηχανήματος έχει επιπλέον βάρος γιαυτ χρειάζονται δύο για την
μεταφορά.
ΑΠΟΜΑΚΡΥΝΣΗ ΚΑΙ ΑΝΤΙΚΑΤΑΣΤΑΣΗ ΜΕΡΩΝ - ΑΝΤΑΛΛΑΚΤΙΚΩΝ
l
Εγκατάσταση , μετατροπή ή έλεγχος ρουτίνας μπορεί να γίνεται μνο απ εξουσιοδοτημένα
άτομα .
l
Δεν πρέπει να γίνονται μετατροπές στα μηχανήματα ωρίς έγκριση . Μπορεί να προκληθεί
απρβλεπτος κίνδυνος.
l
Μνο μέρη που διευκρινίζονται απ την εταιρεία NAMCO EUROPE Ltd μπορούν να
χρησιμοποιηθούν για αντικατάσταση ή επιδιρθωση. (συμπεριλαμβάνοντε και οι βίδες)
l
l
Να είναι σίγουρα κλειστ το ρεύμα πριν οποιαδήποτε δουλειά στο μηχάνημα.
l
Μέρη του τροφοδοτικού ή του μνιτορ παραμένουν ζεστά ή έχουν υψηλή τάση ακμα και ταν
σβήσει το μηχάνημα και μπορούν να προκαλέσουν κάψιμο ή λεκτροσκ.Γιαυτ δεν πρέπει να
έρχονται σε επαφή με χέρια .
l
l
Το μηχάνημα πρέπει να είναι σβηστ κατά την σύνδεση ή αποσύνδεση πρίζας ή κονέκτορα.
Εάν γίνει κάποια δουλειά στο μηχάνημα χωρίς να διευκρινίζεται στο εγχειρίδιο , να
επικοινωνήσεις με τον αντιπρσωπο για οδηγίες γιατί καμία ευθύνη δεν φέρουμε για
καταστροφές ή βλάβες.
Κατά την απομάκρυνση των κεντρικών κονέκτορ απ το μηχάνημα ή της κυρίας πρίζας , πρέπει
να πιάνουμε το πλαστικ μέρος και χι το καλώδιο.
17

Nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè
sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in
altro modo copiata per uso pubblico o privato, senza l’autorizzazione di NAMCO EUROPE LIMITED.
Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della
pubblicazione. Tuttavia NAMCO EUROPE LIMITED, si riserva il diritto di apporre cabiamenti e variazioni senza
alcun preavviso.
Questo apparecchio è stato costruito in conformità alle Direttive della Comunità Europea, ed è stato provato e
soddisfa le Direttive 89/336/EEC e 72/23/EEC per l’applicazione degli standards delle norme EN55014-1,
EN55014-2 e EN60334-2-82 (vedi fronte del manuale), e per questo porta il marchio CE. Qualsiasi cambiamento o
modifica di questo apparecchio deve essere in conformità con le Direttive della Comunità Europea.
In caso di condizioni di estrema interferenza dall’esterno, per esempio trasmissioni radio, scariche elettrostatiche o
transitori sulla linea, può verificarsi un decadimento delle prestazioni. Comunque l’apparecchio ritornerà al
rendimento normale quando la sorgente dell,interferenza avrà cessato di emettere o sarà stata rimossa.
Nota bene: se il processore del gioco “resetta” a causa di una interruzione o diminuzione del voltaggio di linea, un
eventuale credito, già concesso, può essere annullato.
Questo goco non è una macchina così come viene definita dalla Direttiva Macchine 89/392/EEC.
AVVERTENZE PER LA SICUEZZA
Allo scopo di usare questo apparecchio in sicurezza, leggere questo Manuale dell’operatore attentamente prima
dell’installazione, regolazione o uso di questa macchina.
Tutte le volte che il proprietario di questo apparecchio affida lo smontaggio, l’installazione, la regolazione o la
manutenzione ordinaria ad un’altra persona, il proprietario stesso deve assicurarsi che quella persona legga le
precauzioni necessarie e i paragrafi importanti di questo manuale prima di iniziare a lavorare.
Perchè non succeda alcun incidente quando la macchina è operante, seguire rigorosamente le note sulla
sicurezza come specificato più avanti.
Questo manuale insieme con il manuale di installazione (dove si può applicare) forma una parte integrante
dell’apparechio e deve essere disponibile sempre al personale operante e di servizio.
Quest macchina deve essere usata solo in interni e deve essere usata solo per gli scopi per cui è progettata.
Namco Europe Ltd non si assume responsabilità per incidenti, ferite o damni risultanti da cambiamenti non
autorizzati o da uso improprio della macchina.
NOTE PER LA SICUREZZA
Le seguenti note sulla sicurezza sono usate dal principio alla fine di questo manuale. Valutare attentamente
ciascuna di queste note ed il loro significato prima di installare, fare assistenza o regolazioni su questa
macchina.
WARNING
l
“Warning” evidenzia un rischio di ferita o di morte. Non procedere oltre una nota
“Warning” finchè le avvertenze specifcate non siano completamente capite e
conosciute.
CAUTION
“Caution” evidenzia un rischio di danneggiare la macchina. Non proceder oltre una note
“Caution” finchè le avvertenze specificate non siano completamente capite e conosciute.
CONSIDERAZIONI GENERALI SULLA SICUREZZA
l
Mettere in funzione l’apparecchio solo dopo aver controllato che l’installazione sia stata effettuata
correttamente ed in conformità alle istruzioni del manuale.
l
Gli avvisi “Warning” devono sempre essere conservati in buone condizioni e sostituti se consumati,
cosicchè il cliente li possa leggere chiaramente.
l
Se vi sono errori o problemi con la macchina, si deve interrompere il funzionamento immediatamente
e risolvere il problema prima di ogni ulteriore uso.
l
L’installazione, l’assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo
da persone idonee e qualificate.
l
Per una protezione costante contro il rischio di fuoco, assicurarsi che i fusibili sulle alimentazioni
siano solo sostituiti con lo stesso tipo e caratteristiche. L’uso di altri fusibili o materiali è proibito.
l
L’alimentatore all’interno del monitor rimane caldo ed ha zone di alto voltaggio anche se la macchina
è stata spenta, c’è quindi la possibilità di bruciature o scosse elettriche. Fare attenzione a non
toccare queste zone.
l
Per prevenire possibili scosse elettriche dovute a difetti, quest macchina DEVE essere installata con
un connettore sicuramente MESSO A TERRA.
l
l
In caso il cavo di alimentazione di rete risultasse danneggiato deve essere sostituito immedatamente.
18
Non accendere la macchina finchè la stessa non è stata installata completamente e correttamente.
Prima di collegare la macchina alla rete, assicurarsi che la macchina sia preparata per il voltaggio corretto e
che siano inseriti i fusibili adatti.
NOTES D’INSTALLATION
Allo scopo di prevenire possibili scosse elettriche, la
macchina deve essere obbligatoriamente collegata alla
rete con un connettore messo a terra con connessioni
sicure.
3m40cm or more
50cm or more
50cm or more
50cm or more
l
2m90cm or more
Perchè i clienti non siano feriti dal movimento del gioco,
assicurarsi che ci siano almeno 500mm di distanza
rispetto alle altre macchine o rispetto al muro.
Per evitare danni alla macchina durante la messa in opera,
assicurarsi che il voltaggio della rete sia 230 volts AC.
Play zone
Note: Il luogo di destinazione della macchina deve avere il
pavimento liscio e si raccomanda di sistemare dei cuscinetti
di gomma sotto i piedini di livellamento per prevenire lo
sciovolament della macchina sul pavimento.
50cm or more
NON ACCENDERE MAI la macchina finchè l’installazione
non è stata completata.
1m or more
l
Aisle
Maintenance zone
Note: Per garantire l’accesso all’alimentatore e alla scheda madre,
assicurarsi che il retro del mobile principale sia separato dalla
parete o da altre macchine di almeno 500mm.
l
Il gioco è fornito di ruote per rendere più facile il suo spostamento. Fare attenzione quando si
muove la macchina su una superficie inclinata.
l
La testata ha il baricentro spostato in avanti, è perciò importante che ci siano almeno 2 persone
per montare o smontare la testata stessa.
l
La posizione di fissaggio della testata è molto alta, ed è importante che ci sia un mezzo
disponibile per raggiungere tale altezza in sicurezza e senza allungamenti. (Ad esempio scalini,
scale portatili etc.)
l
L’altezza totale della parte principale è 2340mm, fare attenzione ad eventuali ostacoli sopra la
testata ovvero ad eventuali installazioni di luci.
RIMOZIONE E SOSTITUZIONE DI GRUPPI E PARTI STACCATE
l
L’installazione, l’assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite
solo da persone idonee e qualificate.
l
Non apporre alcuna modifica alla macchina senza autorizzazione preventiva. Il fare questo può
causare un pericolo non prevedibile.
l
Quando si rimpiazza o si riparano delle parti (incluse le viti) si possono usare solo parti
approvate dalla Namco Europe Ltd.
l
Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di
manutenzione (guasti, riparazioni etc.)
l
Se state per iniziare un lavoro non descritto in questo manuale, contattate il vostro distributore
per instruzioni poichè non si accetta alcuna responsabilità per danni o ferite.
l
Parti dell’alimentatore e del monitor rimangono caldi o portano alta tensione anche dopo aver
spento l’apparecchiatura e possono causare bruciature o scosse elettriche. Attenzione a non
toccare queste parti accidentalmente.
l
Assicurarsi che la macchina abbia l’interruttore nella posizione OFF prima di inserire o
disinserire qualsiasi connettore o spina.
l
Quando vengono rimossi i connettori principali dalla macchina oppure la spina
dell’alimentazione dalla parete bisogna sempre afferrare il connettore e non il cavo.
19

Ingen del av denne utgivelsen må reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i
form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat
bruk, uten tillatelse fra NAMCO EUROPE LIMITED.
Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP
LIMITED seg retten til å lage forandringer uten varsel.
Denne maskinen er produsert i samsvar med direktiver framsatt av det Europeiske samfunn. Maskinen er testet og
samsvarer med direktivene 89/336/EEC og 72/23/eec med anvendelse av EN55014-1, EN55014-2 og EN60334-2-82
standarder (se i begynnelsen av manualen), og derfor bærer CE merket. Hvilken som helst forandring eller
modifisering må skje etter direktivene satt av det Europeiske samfunn. Uautoriserte forandringer på dette produktet,
kan motstride disse direktivene.
Under noen forhold av ekstreme ytre forstyrrelser, f.eks radio sendere, elektronisk utladning eller transiente
spenninger, kan man regne med noe senket ytelse. Men maskinen vil oppnå normal ytelse når kilden til forstyrrelsene
opphører eller er fysisk fjernet.
Merk:- Hvis spillets prosessor resettes p.g.a et kutt eller reduksjon av hovedspenningen kan oppsparte kreditt på
spillet forsvinne.
Dette spillet er ikke en maskin som er definert ved Maskin direktivet 89/392/EEC.
Sikkerhets advarsel.
For å bruke denne maskinen uten noe form for fare, sørg for å lese denne manualen nøye før installasjon,
justeringer eller bruk av maskinen.
Når eieren av denne maskinen overlater avmontering, installasjon, justering eller rutine vedlikehold til en annen
person, skal eieren forsikre seg om at denne personen leser de passende forsiktighetsreglene og relevante deler
av manualen før han starter på arbeidet.
For å forhindre at ulykker inntreffer når maskinen er i drift, følg strengt teksten om sikkerhet som beskrevet
nedenfor.
Denne manualen sammen med installasjons manualen (hvor det er anvendelig) er en intrigert del av utstyret og
må være tilgjengelig for drift- og servispersonell til alle tider.
Denne maskinen er bare for innendørs bruk og skal bare benyttes etter mente hensikter.
Namco Ltd. bærer intet ansvar ved ulykker, kvestelse eller skade som følge av uautoriserte forandringer, eller for
uriktig buk av maskinen.
Sikkerhets beskjeder.
Følgende sikkerhets punkter er brukt ut denne manualen. Gjør deg kjent med disse punktene og deres
mening før installasjon, service eller du utfører noen innstillinger på denne maskinen.
ADVARSEL
l
Advarsel innebærer en risiko som kan føre til kvestelse eller død. Ikke fortsett utover
advarslen før den er ordentlig forstått og mottiltak er igangsatt.
FORSIKTIG
Forsiktig innebærer en risiko som kan medføre skade på maskinen. Ikke fortsett utover
advarslen før den er ordentlig forstått og mottiltak er igangsatt.
VANLIGE SIKKERHETSTILTAK
l
l
Advarsel skiltene må bestandig holdes i skikket stand og eventuelt byttes ut hvis det oppstår skade på
dem, slik at kunden uten vanskelighet kan lese dem.
l
Hvis det er en feil eller et problem med maskinen, må den straks settes ut av funksjon. Og må under
ingen omstendigheter startes før problemet er rettet på.
l
l
Installasjon, service, justering eller rutine vedlikehold skal bare utføres av kvalifiserte personer.
l
Strømforsyningen inne i monitoren vill være varm og ha områder med høy spenning selv om maskinen
har blitt slått av. og det er muligheter for skader og elektriske sjokk. Vær forsiktig så du ikke berører
disse områdene.
l
For å forhindre mulige elektriske sjokk grunnet funksjonsfeil, må denne maskinen være ordentlig
jordet.
l
l
Hvis ledningen til hoved strømforsyningen skades må den straks byttes ut.
20
Bruk bare denne maskinen etter å ha kontrollert at den er korrekt installert ifølge manualen.
For fortsatt beskyttelse mot brann, forsikre deg at hoved sikringen bare byttes ut med en av samme
type og verdi. Bruk av andre sikringer eller materiale er forbudt.
Ikke slå på maskinen før den er korrekt installert.
Før du kopler maskinen til strømnettet, forsikre deg om at maskinen innstilt for den korrekte spenningen og de
riktige sikringene benyttes.
MERKNADER VED INSTALLASJON
l
l
Slå ALDRI på maskinens strømforsyning før installasjonen er fullført.
For å forhindre eventuelle elektriske sjokk, forsikre deg om at
maskinen er koplet til et strømnett med ordentlig jording.
MERKNADER: Hvis plassen hvor spillet skal plasseres har polerte gulv
anbefales det at du benytter gummi sko under nivå
justeringene, for å forhindre at maskinen kan flytte på seg.
MERKNADER: For å få adgang til strømforsyningen og CPU-kort, forsikre
deg om at bakparten av hoved kabinettet er skilt fra vegger
eller andre maskiner med minst 500mm.
50cm or more
For å forhindre skade på maskinen p.g.a. feil bruk, sørg for at
spenningen til hoved strømforsyningen er 230Volt AC.
2m90cm or more
50cm or more
50cm or more
For å forhindre at kundene blir skadet av spillets bevegelige
deler. forsikre deg om at det er minst 500mm avstand mellom
andre maskiner eller vegger.
Play zone
1m or more
l
3m40cm or more
50cm or more
Aisle
Maintenance zone
l
Spillet har montert hjul for å gjøre det letter å flytte på. Hver forsiktig når det skal flyttes på en
hellende overflate.
l
Hoved enheten i spillet har tyngdepunktet i fronten, så det er viktig at minst 2 personer blir
brukt til å montere eller flytte denne enheten.
l
Monterings posisjonen til hoved enheten er veldig høy, og det er viktig at denne høyden nås
sikkert, uten at man må strekke seg. Benytt deg av hjelpemiddel. (f.eks sto, krakk, gardintrapp
osv)
l
Den totale høyden på hoved enheten er 2340mm. vær forsiktig med høye hindringer som f.eks
lysrør.
FJERNE OG UTSKIFTE ENHETER OG DELER.
Installasjon, service, justering eller rutine vedlikehold skal bare utføres av kvalifiserte personer.
l
Ikke lag noen forandringer på denne maskinen uten godkjenning. Dette kan medføre uforutsette
farer.
l
Bare deler spesifisert av Namco Europe Ltd. skal benyttes ved utskifting eller reparasjon av
deler (dette gjelder også skruer).
l
Forsikre deg om at strømmen er slått av før du påbegynner noe som helst vedlikeholdsarbeid
(feilsøking, reparasjon osv.)
l
Hvis du utfører arbeid som ikke er beskrevet i denne manualen, ta kontakt med din distributør
for instruksjon da ikke noe ansvar vill bli akseptert for skade på maskin eller på personer.
l
Deler av strømforsyningen og monitoren er fortsatt varm eller bærer høye spenninger selv etter
strømmen er slått av og kan forsake skader eller elektriske sjokk. Forsikre deg om at du ikke
berører disse delene.
l
Forsikre deg om at maskinen er slått av før du kopler sammen eller tar fra hverandre plugger
eller koplinger.
l
Når du fjerner hoved koplingene fra maskinen, eller hoved pluggen fra støpselet, ta bestandig
tak i pluggen og ikke ledningen.
21

Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of
in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem,
doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe
Limited.
Ofschoon de informatie in deze handleiding in goed vertrouwen is gegeven en nauwkeurig was ten tijde van het
drukken, houdt Namco zich het recht voor om veranderingen en aanpassingen te maken zonder bericht.
Deze machine is geproduceerd volgens Richtlijnen van de Europese Gemeenschap, en is getest en is in
overeenstemming met de Richtlijnen 89/336/EEC en 72/23/EEC door de toepassing van de standaards EN55014-1,
EN55014-2 en EN60334-2-82 (zie voorin de handleiding) en draagt als zodanig het CE-merk. Enige veranderingen
of aanpassingen aan deze machine dienen in overeenstemming te zijn met de Richtlijnen van de Europese
Gemeenschap. Enige ongeauthoriseerde veranderingen aan dit produkt kunnen in strijd zijn met deze Richtlijnen.
Onder sommige omstandigheden van extreme externe storingen, bijv. radiotransmissies, electrostatische
ontladingen of pieken op het net, kan prestatieteruggang optreden. De machine zal echter normaal presteren zodra
de storingsbron gestopt of verwijderd is.
Let op: - als de spelprocessor reset a.g.v. een onderbreking of vermindering van de netstroom, dan kunnen
opgebouwde credits verloren gaan.
Dit spel is niet een machine zoals omschreven in de Machinery Directive 89/392/EEC.
Veiligheidsopmerkingen
Om deze machine veilig te kunnen gebruiken, dient vóór installatie, aanpassing of gebruik van deze machine, de
Bedieningshandleiding zorgvuldig gelezen te worden.
Telkens wanneer de eigenaar van deze machine de demontage, installatie, aanpassing of routine-onderhoud
toevertrouwd aan een andere persoon, dient de eigenaar er voor te zorgen dat deze persoon de juiste
voorzorgsmaatregelen en relevante gedeeltes uit de handleiding leest voordat hij begint.
Om er voor te zorgen dat geen ongelukken gebeuren als de machine gebruikt wordt, dienen onderstaande
veiligheidsaanwijzingen zorgvuldig opgevolgd te worden.
Deze handleiding maakt samen met de installatiehandleiding (waar van toepassing) een integraal deel uit van de
apparatuur en moet te allen tijde ter beschikking staan van exploitatie- en onderhoudspersoneel.
Deze machine is alleen bedoeld voor gebruik binnenshuis en dient alleen gebruikt te worden voor bedoelde
doeleinden.
Namco Ltd. is niet verantwoordelijk voor ongelukken, letsel of schade die voortkomt uit ongeoorloofde
veranderingen aan of onjuist gebruik van deze machine.
Veiligheidsopmerkingen
De volgende veiligheidsopmerkingen worden overal in deze handleiding gebruikt. Maak uzelf vertrouwd met deze
opmerkingen en hun betekenis vóór installatie, het plegen van onderhoud of het aanbrengen van aanpassingen
aan deze machine.
WAARSCHUWING l
VOORZICHTIG
Waarschuwing geeft een gevaar aan dat zou kunnen resulteren in letsel of de
dood. Ga niet verder dan een waarschuwingsopmerking totdat de aangegeven
omstandigheden volledig begrepen zijn en hieraan voldaan is.
Voorzichtig geeft een gevaar aan dat zou kunnen resulteren in schade aan de machine.
Ga niet verder dan een voorzichtigheidsopmerking totdat de aangegeven
omstandigheden volledig begrepen zijn en hieraan voldaan is
ALGEMENE VEILIGHEIDSOVERWEGINGEN
l
Stel deze machine alleen in gebruik nadat gecontroleerd is of de machine correct en overeenkomstig
de handleiding is geïnstalleerd.
l
De waarschuwingsstickers dienen altijd in goede staat te worden gehouden en vervangen indien
versleten, zodat de klant ze goed kan lezen.
l
Als zich een fout of probleem voordoet met de machine, dan dient de machine onmiddellijk stopgezet
en het probleem verholpen te worden voordat de machine verder gebruikt wordt.
l
Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin
bekwame personen.
l
Om blijvende bescherming tegen brandgevaar te garanderen, dient ervoor gezorgd te worden dat de
netzekeringen alleen vervangen worden door zekeringen van hetzelfde type en dezelfde sterkte. het
gebruik van andere zekeringen of ander materiaal is verboden.
l
De voeding in de monitor blijft warm en er kunnen componenten electrisch geladen blijven ondanks
dat de machine UITgeschakeld is, waardoor er brandwonden of electrischee schokken kunnen
worden opgelopen. Ben voorzichting en raak deze delen niet aan.
l
Om mogelijke electrische schokken a.g.v. storingen te voorkomen, MOET deze machine voorzien zijn
van een goed vastzittende aardstekker.
l
Mocht het netsnoer op enig moment beschadigd worden, dan moet deze onmiddellijk vervangen
worden.
l
Zet de machine niet AAN totdat deze correct is geïnstalleerd.
22
Voordat de machine op het lichtnet wordt aangesloten, dient gecontroleerd te worden of de machine op het
correcte voltage staat afgesteld en of de correcte zekeringen zijn aangebracht.
Opmerkingen aangaande Installatie
l
Om ervoor te zorgen dat klanten niet gewond raken door de
beweging van het spel, dient ervoor gezorgd te worden dat er
minimaal 500mm ruimte is tussen andere machines of muren.
Om schade aan de machine door verkeerd gebruik te voorkomen,
dient ervoor gezorgd te worden dat het voltage van het lichtnet
230volts AC bedraagt.
OPMERKING:
Als de machine op een gladde ondergrond wordt
gebruikt, is het raadzaam rubber matjes onder de stelpootjes
te bevestigen om te voorkomen dat de machine over de
vloer gaat glijden.
3m40cm or more
50cm or more
50cm or more
50cm or more
Om mogelijke electrische schokken te voorkomen, dient ervoor
gezorgd te worden dat de machine middels een goed vastzittende
aardstekker op het lichtnet is aangesloten.
2m90cm or more
l
Play zone
50cm or more
Sluit de machine nooit aan op de stroomtoevoer totdat de
installatie is voltooid.
1m or more
l
Aisle
Maintenance zone
OPMERKING:
Om toegang te krijgen tot de voeding- en de CPUassemblies, dient ervoor gezorgd te worden dat de
achterkant van het kabinet minimaal 500mm verwijderd is
van de muur of andere machines.
l
Het spel is voorzien van wieltjes, waardoor het gemakkelijker is om te verplaatsen. Wees
voorzichtig als de machine op een hellend vlak gereden wordt.
l
Het zwaartepunt van de Header Assembly ligt aan diens voorkant, waardoor het belangrijk is dat
minimaal 2 personen de Header Assembly aanbrengen of verwijderen.
l
De Header Assembly moet op een hoge positie geplaatst worden en het is dus belangrijk dat
deze hoogte veilig kan worden bereikt zonder veel te strekken. (bijv. middels een trap of een
kruk)
l
De hoogte van het hoofdgedeelte is 2340mm: kijk dus uit voor obstakels zoals lampen.
Verwijderen en vervangen van Assemblies en onderdelen
l
Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door
hierin bekwame personen.
l
Maak geen veranderingen aan deze machine zonder goedkeuring vooraf. Dit kan onvoorzien gevaar
opleveren.
l
Alleen onderdelen die door Namco Europe Ltd. zijn gespecificeerd dienen gebruikt te worden bij
het vervangen of repareren van onderdelen (incl. schroeven).
l
Zorg ervoor dat de machine UITgeschakeld is voordat er enig onderhoudswerk wordt verricht
(troubleshooting, reparaties etc.)
l
l
Bij het verrichten van werkzaamheden die niet in deze handleiding staan beschreven, dient voor
instructies altijd contact opgenomen te worden met de verdeler aangezien geen verantwoording
wordt genomen voor schade of letsel.
Delen van de voeding en de monitor blijven warm of behouden hoogspanning zelfs nadat de
machine UITgeschakeld is en zouden verbrandingen of electrische schokken kunnen veroorzaken.
Ben voorzichting en raak deze delen niet per ongeluk aan.
l
Zorg ervoor dat de machine is UITgeschakeld voordat pluggen of connectors ingestoken of
uitgetrokken worden.
l
Als het netsnoer uit de machine of uit het stopcontact verwijderd wordt, dient altijd de stekker
vastgepakt te worden en niet het snoer.
23

Nenhuma parte desta publicacão poderá ser reproduzida por processos mecanográficos, fotográficos, electrónicos
ou ainda sob a forma de gravacão sonora nem tão pouco poderá ser gravada através de sistemas informáticos
transmissiveis ou de outra forma copiados para uso publico ou privado sem autorização expressa da NAMCO
EUROPA LIMITADA.
A informação contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicação. A NAMCO
EUROPA LIMITADA, reserva-se o direito de proceder a mudanças e alterações sem qualquer aviso prévio.
Esta maquina foi fabricada de acordo com as Directivas Comunitárias Europeias e tem sido testada em conformidade
com as seguintes Directivas: 89/336/EEC e 72/23/EEC através dos requerimentos normativos, EN55014-1,
EN55014-2 e EN60334-2-82 (ver capa frontal do manual) e como tal sustenta o certificado de marca de CE.
Quaisqueres alterações ou modificações efectuadas nesta maquina deverão ser em conformidade com as Directivas
da Comunidade Europeia. Quaisquer alterações não autorizadas a este equipamento poderão infrigir tais Directivas.
O funcionamento normal desta maquina, poderá ser afectado debaixo de algumas condicões extremas de
interferências externas tais como; transmissões via radio, descargas electroestáticas e passagens de corrente na
rede de alimentação. Contudo o seu funcionamento normal será restabelecido logo que a fonte de interferências
tenha cessado ou tenha sido neutralizada.
Nota :- Se o processador de jogo for inicializado devido a uma interrupção ou quebra da corrente principal,
quaisqueres creditos obtidos poderão desaparecer.
Este jogo por si só não contitui uma maquina tal como defenido pelas Directivas de Maquinaria de 89/392/EEC8.
AVISOS DE SEGURANÇA
Afim de usar esta maquina com segurança, certifique-se que lê este manual de operador atentamente antes de
proceder á montagem e afinação ou uso da mesma.
Sempre que o proprietário desta maquina confiar a desmontagem, instalação, afinação ou manutenção preventiva
da mesma a outra pessoa, deverá este assegurar - se que a pessoa em questão lê as precauções apropriadas e
capitulos relevantes deste manual antes de iniciar o trabalho.
Afim de evitar qualquer tipo de acidente quando a maquina estiver em funcionamento, deverá seguir
rigorosamente os procedimentos de segurança descritos abaixo.
Este manual juntamente com o manual de instalação (aonde aplicavel), contituem parte integrante do
equipamento e deverão estar sempre disponiveis ao operador e pessoal tecnico de assistência.
Esta maquina destina-se a ser operada em espaços interiores apenas e a sua utilização deve circunscrever-se
somente aos fins previstos.
A Namco Ltd. declina qualquer responsabilidade por acidentes, ferimentos ou danos resultantes de modificações
não autorizadas ou uso indevido desta maquina.
AVISOS DE SEGURANÇA
Os seguintes avisos de segurança são usados através de todo o manual. Familarize-se com cada um destes
avisos e respectivos significados antes de instalar, assistir ou efectuar qualquer afinação nesta maquina.
l
Perigo revela uma situação anormal que poderá resultar em ferimentos ou morte. Não
avance para além de um aviso de Perigo sem que todas as condições indicadas estejam
completamente esclarecidas e resolvidas.
CAUTELA
Cautela revela uma situação anormal que poderá resultar em danos materiais para a maquina.
Não avance para além de um aviso de Cautela sem que todas as condições indicadas estejam
completamente esclarecidas e resolvidas.
PERIGO
AVISOS DE PERIGO
l
Esta maquina só deverá ser colocada em funcionamento após ter sido verificado que se encontra
instalada correctamente e de acordo com o manual de instruções.
l
Os avisos de perigo devem ser sempre mantidos em boas condições de leitura de forma a permitir uma
leitura clara por parte do utilizador, caso se encontrem danificados deverão ser substituidos.
l
Caso esta maquina manifeste algum erro ou problema durante o seu funcionamento, deverá ser
imediatamente parada até que o problema em questão seja rectificado.
l
A montagem, assistência e afinações ou manutenção de rotina desta maquina, deverão ser somente
executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.
l
Afim de garantir uma proteção anti - fogo permanente nesta maquina, certifique-se que os fusiveis de
proteção são sempre substituidos por fusiveis de igual valor ou calibre aos de origem. O uso de outro
tipo de fusiveis ou material é proibido.
l
A fonte de alimentação do monitor encontrar-se-à quente, tendo zonas de alta voltagem, mesmo após a
maquina ter sido desligada. Deste facto poderá resultar a ocurrência de queimaduras ou choques
electricos. Seja cuidadoso para evitar contacto com estas zonas.
l
Esta maquina deve estar sempre equipada com uma ficha com circuito de protecção à Terra, afim de
evitar possiveis choques electricos, caso surga uma falha no sistema.
l
Se a qualquer altura o cabo de alimentação principal ficar danificado, deverá ser imediatamente
substituido.
l
Não ligar a maquina sem que esta tenha sido correctamente instalada.
24
Antes de ligar a maquina à tomada da rede de alimentação principal, certifique-se de que a maquina está
preparada para a voltagem correspondente e de que também se encontra protegida com os fusiveis
apropriados.
NOTAS SOBRE A INSTALAÇÃO
3m40cm or more
50cm or more
50cm or more
50cm or more
l
Afim de evitar possiveis choques electricos, certifique-se que a
maquina está ligada à rede de alimentação com uma ficha
protegida com circuito de terra.
Afim de evitar ferimentos pessoais nos clientes, provocados pelo
movimento da maquina, certifique-se que existe pelo menos
500mm de separação entre outras maquinas ou paredes.
2m90cm or more
l
NUNCA ligar a maquina sem que a instalação esteja
completamente finalizada.
Afim de evitar danos na maquina causados por falhas de
operação, certifique-se que a voltagem da rede de alimentação
principal é de 230volt AC.
50cm or more
l
1m or more
Play zone
NOTAS : Se esta maquina estiver colocada sobre um chão polido,
recomenda-se a utilização de tapetes de borracha debaixo dos
pés niveladores, afim de prevenir a maquina de deslizar no chão.
Aisle
Maintenance zone
NOTAS : Quando precisar de aceder à fonte de alimentação e ás placas
(CPU), certifique-se que a parte trazeira do móvel central está
separada da parede ou de outras maquinas pelo menos 500mm
afim de ganhar espaço de manobra.
l
Esta maquina está equipada com rodas afim de facilitar a sua deslocação tenha cuidado ao
mover a maquina num plano inclinado.
l
O bloco Superior (Cabeça) tem o centro de gravidade para a frente, porconseguinte é
importante que pelo menos sejam utilizadas duas pessoas para montar ou desmontar este
Bloco Superior.
l
A posição do bloco superior quando montado na maquina é muito alta. Torna-se importante ter
meios seguros de alcance, tais como; escadotes ou escadas afim de evitar riscos
desnecessários.
l
A altura total do bloco principal, é de 2340mm, tenha cuidado com qualquer tipo de obstruções
existentes em altura como por exemplo; calhas electricas ou candeiros.
SUBSTITUIÇÃO E MONTAGEM DE PEÇAS
l
A montagem, assistência e afinações ou manutenção de rotina desta maquina, deverão ser
somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.
l
Não faça qualquer tipo de alteração prévia nesta maquina sem aprovação prévia. Se tal
acontecer poderá provocar danos e perigos imprevisiveis.
l
A substituição ou reparação de peças deverá ser feita apenas com peças de origem ou
especificadas pela “Namco Europa Ltd.” (incluindo parafusos)
l
Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho
de manutenção. (identifação de avarias, reparação etc.)
l
Caso esteja a efectuar um trabalho não descrito neste manual, certifique-se que contacta o seu
distribuidor para obter instruções, caso contrário não serão aceites responsabilidades por
danos causados ou ferimentos.
l
Algumas zonas da fonte de alimentação e do monitor ficam quentes e transportam correntes de
alta voltagem, mesmo depois de a maquina ter sido desligada, podendo causar queimaduras e
choques electricos. Tome cuidado para não tocar acidentalmente estas zonas.
l
Certifique-se que a maquina está desligada antes de ligar ou desligar qualquer tipo de fichas ou
junções.
l
Quando desligar a ficha principal da maquina ou a ficha do cabo de alimentação das tomadas
da parede, deverá sempre agarrar na ficha e nunca puxar pelo cabo da mesma.
25

Ingen del av denna publikation får reproduceras, varken fotografiskt, elektroniskt eller i någon form av
ljudinspelning. Det får inte heller lagras i något återvinningssystem, översändas eller på annat sätt kopieras för
offentlig eller privat användning, utan tillstånd från NAMCO EUROPE LIMITED.
Eftersom informationen i denna manual lämnas ut i god tro och var korrekt när den trycktes, reserverar sig
NAMCO EUROPE LIMITED för ändringar.
Denna maskin har tillverkats enligt direktiv från europeiska unionen, är testad och uppfyller direktiven enligt 89/
336EEC och
72/23/EEC med tillämpning av EN55014-1, EN55014-2 och EN60334-2-82 standard (se manualens framsida) och
bär därmed också CE-märket. Varje förändring eller modifiering av denna maskin måste ske i överens-stämmelse
med EU-direktiven.
En förändring i denna produkt, som inte är auktoriserad, kan strida mot dessa direktiv.
Under vissa omständigheter när det gäller extrema externa störningar, t ex radiosändningar, elektrostatiska
urladdningar eller nätburna strömstörningar, kan resultera i en något nedsatt funktion. Maskinen kommer dock att
återgå till normal funktion, så snart störningen har upphört eller avlägsnats
OBS! Om spelprocessorn startar om till följd av ett avbrott eller reducering av strömmen kan registrerade krediter
gå förlorade.
Detta spel är inte en maskin enligt definitionen i Maskindirektivet 89/392/EEC
SÄKERHETS VARNING
För att maskinen ska kunna användas på ett säkert sätt, ska manualen läsas noggrant före installation, användning
eller justering.
Om ägaren till maskinen anförtror någon annan person att montera isär, installera, justera maskinen eller utföra
rutinunderhåll, ska ägaren försäkra sig om att denna person läser om försiktighetsåtgärder och tillämpliga delar av
denna manual innan arbetet påbörjas.
För att förhindra att någon olycka händer när maskinen är igång, måste säkerhetspunkterna beskrivna nedan följas
strikt.
Denna manual tillsammans med installationsmanualen (när tillämpligt) utgör en integrerad del av utrustningen och
måste vara ständigt tillgänglig för operatörer och service personal.
Maskinen är avsedd för inomhusbruk och ska endast användas för detta ändamål.
Namco Ltd. bär inget ansvar för olyckor eller skador som orsakats av icke auktoriserade ändringar i maskinen eller
felaktigt användande av densamma.
SÄKERHETSANVISNINGAR
Säkerhetsanvisningarna nedan används genomgående i manualen. Gör dig förtrogen med varje anvisning och
dess innebörd innan installation, service eller justeringar görs på denna maskin.
VARNING
l
OBSERVERA
”Varning” anger en fara som skulle kunna skada eller förorsaka dödsfall. Fortsätt inte
vid en sådan varningsanvising innan de påvisade förhållandena är förstådda och
åtgärdade i sin helhet.
”OBSERVERA” anger en fara som skulle kunna förorsaka skada på maskinen. Fortsätt inte
vid en sådan varningsanvising innan de påvisade förhållandena är förstådda och åtgärdade i
sin helhet.
ALLMÄNNA SÄKERHETSBEAKTANDEN
l
Sätt inte igång maskinen utan att ha kontrollerat att den är korrekt installerad och i överensstämmelse
med manualen.
l
Varningsanvisningarna måste alltid hållas i gott skick och ersättas när de blir slitna, så att kunderna
kan läsa dem dem tydligt.
l
Om det uppstår fel eller problem med maskinen, måste användningen stoppas omedelbart och
problemet rättas till innan den åter används.
l
Installation, service, justeringar eller rutinunderhåll ska endast utföras av en för ändamålet
kvalificerad person.
l
För kontinuerligt skydd mot brandfara, ska man försäkra sig om att huvudsäkringarna endast ersätts
med samma typ och specifikationer. Användandet av andra säkringar eller material är förbjuden.
l
Strömförsörjningen inne i monitorn håller sig varm och har områden med hög spänning, även när
maskinen stängts av och det finns risk för brännskada eller elektriska stötar. Var försiktig och vidrör
aldrig sådana områden.
l
För att förhindra en eventuell elektrisk stöt förorsakad av fel, MÅSTE maskinen vara försedd med
säkert ansluten JORDAD kontakt.
l
l
Om strömförsörjningskabeln på något sätt skadas, måste den bytas ut omedelbart.
26
Vrid inte strömbrytaren till ON innan maskinen är korrekt installerad.
Innan strömmen sätts på till maskinen, måste man försäkra sig om att den är inställd på rätt spänning och att
rätt säkringar är isatta.
ATT BEAKTA VID INSTALLATION
l
För att undvika skador av spelets rörelser, försäkra dig om
att det finns ett avstånd på minst 500 mm till annan maskin
eller vägg.
För att undvika skador på maskinen p g a felaktigt
handhavande, försäkra dig om att strömstyrkan är 230 volt
AC.
OBSERVERA:
OBSERVERA:
3m40cm or more
50cm or more
50cm or more
Om maskinen är placerad på ett polerat golv,
rekommenderas att placera gummibrickor under
nivåjusteringen för att förhindra att maskinen glider
på golvet.
50cm or more
För att förhindra elektriska chocker, försäkra dig om att
maskinen kopplas till strömförsörjning med jordad kontakt
2m90cm or more
l
Play zone
50cm or more
Sätt aldrig på strömmen på maskinen innan installationen är
klar.
1m or more
l
Aisle
Maintenance zone
För att kunna komma åt strömförsörjningen och
CPU, se till att baksidan av huvudkabinettet är
placerat minst 500 mm från vägg eller annan maskin.
l
Spelet är försett med hjul för att underlätta förflyttningar. Var försiktig om spelet ska flyttas på en
sluttande yta.
l
Toppskylten har tyngdpunkten framtill, därför är det viktigt att minst 2 personer sätter dit eller tar
bort den.
l
Toppskyltens placering är mycket högt upp och det är viktigt att sådana hjälpmedel används så att
man når upp utan att sträcka sig (t ex trappstege, pall osv).
l
Den totala höjden är 2340 mm, tänk på eventuella högt placerade hinder, t ex lampor.
ATT TA BORT ELLER BYTA UT ENHETER OCH DELAR
l
l
Justeringar och underhåll på denna maskin skall endast utföras av kvalificerad personal.
Gör inga ändringar på denna maskin utan ett godkännande i förväg. Detta kan förorsaka
oförutsägbar fara.
l
Endast delar som är specificerade av Namco Europe Ltd. ska användas vid utbyten eller
reparation av delar (inklusive skruvar).
l
Försäkra dig om att strömmen är avstängd innan underhållsarbete påbörjas (felsökning,
reparationer etc.)
l
Om arbete ska utföras som inte är beskrivet i denna manual, är det viktigt att kontakta
återförsäljaren för instruktioner eftersom inget ansvar accepteras för åverkan eller personskador.
l
Delar av strömförsörjningen och monitorn är varma och strömbärande även efter strömmen
stängts av och kan orsaka brännskador eller elektriska stötar.
l
l
Försäkra dig om att maskinen är avstängd innan kontakter sätts i eller tas ur.
När kontakten tas ur maskinen eller ur väggen, ta alltid tag i kontakten och inte i sladden.
27

Tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman NAMCO EUROPE
LIMITED:in lupaa.
Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. NAMCO EUROPE LIMITED:illä on kuitenkin
oikeus muutoksiin ilman erillistä ilmoitusta.
Tämä laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiivejä:
89/336/EEC ja 72/23/EEC (EN55014-1, EN55014-2 ja EN 60334-2-82 standardit). Näin ollen tämä laite on
varustettu CE-merkinnällä. Kaikki tähän laitteeseen kohdistetut muutokset on tehtävä EC- direktiivien mukaisesti.
Mikä tahansa valtuuttamattoman huoltomiehen tekemä muutos voi olla direktiivien vastainen.
Laitteen toiminta voi häiriintyä määrätyissä olosuhteissa, jotka johtuvat äärimmäisistä ulkoisista sähköhäiriöistä,
kuten radiolähetys, elektrostaattinen purkaus tai vahvavirrasta syntynyt häiriö. Toiminta normalisoituu kuitenkin
heti, kun ulkoinen sähköhäiriö on poistettu.
Huom:- Jos peliprosessori resetoituu sähkökatkoksen tai vastaavan johdosta, voivat kaikki pelivaraukset hävitä.
Tämä laite ei ole 89/392/EEC direktiivien mukainen kone.
Turvallisuusvaroitus
Tämän laitteen turvallinen käyttö edellyttää käyttöohjekirjan huolellista lukemista ennen laitteen asennusta, säätöä
tai käyttöä.
Jos tämän laitteen omistaja antaa jollekin toiselle osapuolelle tehtäväksi purkaa, asentaa, säätää tai muuten
huoltaa laitetta, on omistajan varmistuttava siitä, että toinen osapuoli on lukenut ja ymmärtänyt käyttöohjekirjan
oleelliset osat ennen työhön ryhtymistä.
Turvallisuusohjeita on seurattava tarkoin vahinkojen välttämiseksi laitteen ollessa käytössä .
Tämä ohje sekä mahdollinen asennusohje muodostavat laitteiston oleellisen osan ja on siksi aina oltava huolto- ja
käyttöhenkilökunnan käytettävissä.
Tämä laite on tarkoitettu vain sisätilakäyttöön. Sitä ei saa käyttää muihin tarkoituksiin.
Namco Ltd ei vastaa niistä onnettomuuksista, loukaantumisista tai vahingoista, jotka johtuvat laitteeseen ilman
Namco Ltd:n lupaa tehdyistä muutoksista laitteen väärästä käytöstä.
Turvallisuusohjeet
Tässä käyttöohjekirjassa on käytetty seuraavia turvallisuuteen liittyviä huomautuksia. Tutustu jokaiseen näistä.
Älä asenna, huolla tai säädä laitteistoa, ennen kuin olet täysin ymmärtänyt mitä ne tarkoittavat.
VAARA
l
“Vaara” tarkoittaa uhkaa, joka voi johtaa loukkantumiseen tai kuolemaan, Älä koskaan
ohita Vaara-merkintää, ennenkuin ohjeissa esitetyt olosuhteet on ymmärretty täysin.
VAROITUS
“Varoitus” tarkoittaa uhkaa, joka voi johtaa laitteen vioittumiseen. Älä koskaan ohita Vaaramerkintää, ennenkuin ohjeissa esitetyt olosuhteet on ymmärretty täysin.
YLEISET TURVALLISUUNÄKÖKODAT
l
l
Varmista, että laite on asennettu oikein ja ohjekirjan mukaisesti ennen käyttöönottoa.
l
Jos laitteeseen tulee vika tai ongelmia, on se pysäytettävä välittömästi ja ongelma selvitettävä ennen
uutta käyttöönottoa.
l
Vain riittävän ammattipätevyyden omaava henkilö saa suorittaa asennus-, huolto-, säätö- tai muita
laitteeseen kohdistuvia rutiinitoimenpiteitä.
l
Jotta palovaaraa ei syntyisi, saa pääsulakkeita vaihtaa vain samankokoisiin sulakkeisiin. Muiden
sulakkeiden tai materiaalin käyttö on ehdottomasti kielletty.
l
Monitorin sisällä oleva virtalähde pysyy kuumana ja siinä on alueita, joissa on korkeajännite vaikka
laite on kytketty pois päältä. Palovammojen tai sähköiskun saaminen on mahdollista. Älä koske näihin
alueisiin.
l
Sähköiskujen välttämiseksi vikatapauksissa, laite on ehdottomasti kytkettävä maadoitetulla johdolla
maadoitettuun pistorasiaan.
l
l
Vioittunut verkkojohto on välittömästi vaihdettava.
28
Varoitustaulut on pidettävä hyvässä kunnossa. Jos ne ovat kuluneet, ne on ehdottomasti vaihdettava,
jotta asiakkaalla olisi mahdollisuus lukea niitä selvästi.
Älä kytke laitetta päälle, ennen kuin se on oikein asennettu.
Varmista ennen verkkoon kytkemistä, että virtalähteen jännitteen asetus on asetettu oikealle jännitteelle ja
että siinä on oikeat sulakkeet.
ASENNUSHUOMIOITA
l
Älä koskaan kytke laitetta päälle ennen kuin asennus on
suoritettu loppuun.
3m40cm or more
Varmista, että virtalähteen jännite on 230 V AC, jotta ei laite vioitu.
Huomio: Jos tämä laite sijoitetaan liukkaalle esim. vahatulle lattialle,
suositellaan laitettavaksi kumityynyt säätöjalkoihin liikkumisen
estämiseksi.
50cm or more
Varmista, että laitteen ja seinän tai toisen laitteen välissä on
vähintään 500 mm, jotta asiakkaat eivät loukkaannu laitteen
likkumisesta johtuen.
2m90cm or more
l
50cm or more
Play zone
50cm or more
Tämän laitteen virtalähde on kytkettävä maadoitetulla
johdolla maadoitettuun pistorasiaan, jotta sähköiskun vaaraa
ei olisi.
1m or more
l
50cm or more
Aisle
Maintenance zone
Huomio: Varmista, että takaosan taakse jää vähintään 500 mm tilaa,
jotta virtalähteeseen ja CPU-korttiin pääsee käsiksi.
l
Laite on varustettu kääntyvillä pyörillä. Tämä on pidettävä mielessä, kun laitetta siirretään
kaltevalla alustalla.
l
Yläosan painopiste on yläosan etuosassa. Tästä syystä on yläosaa asennettaessa tai
poistettaessa oltava vähintään kaksi henkilöä.
l
Yläosan asennusasento on erittäin korkealla. On tärkeää, että tarvittavalle korkeudelle
päästään vaivattomasti ilman venyttämistä. (esim. käytä tukevia tuoleja tai tikkaita)
l
Laitteen kokonaiskorkeus on yli 2340 mm. Varmista, ettei katossa ole esteitä. esim. valaisimia.
l
Vain riittävän ammattipätevyyden omaava henkilö saa suorittaa asennus-, huolto-, säätö- tai
muita laitteeseen kohdistuvia rutiinitoimenpiteitä.
l
Tälle laitteelle ei saa tehdä mitään hyväksymättömiä muutoksia. Se voi aiheuttaa ennaltaarvaamattomia vaaroja.
l
Vain Namco Europe Ltd:n määrittelemiä varaosia saa käyttää vaihtaessasi tai korjatessasi
osia. (sisältäen ruuvit).
l
Varmista, että laite on kytketty POIS PÄÄLTÄ ennen työn aloittamista.
l
Ota yhteyttä maahantuojaan ohjeita varten, jos joudut tekemään työtehtäviä, joita ei ole esitelty
huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole.
l
Virtalähde ja monitori pysyvät kuumina ja niissä on alueita, joissa on korkeajännite vaikka laite
on kytketty pois päältä. Palovammojen tai sähköiskun saaminen on mahdollista. Älä koske
näihin laitteisiin.
l
Varmista, että laite on kytketty POIS PÄÄLTÄ ennen johtojen kytkemistä tai irrottamista.
l
Irrottaessasi verkkojohdon seinästä tai laitteesta, ota kiinni itse pistokkeesta, ei johdosta.
29
1. SPECIFICATIONS
POWER SUPPLY:-
230vAC (50/60Hz)
MAX. POWER CONSUMPTION:
590watts
AMBIENT OPERATING
TEMPERATURE
+5°C to +25°C
MONITOR:-
Thomson 46” Projection - 46KH412S
COIN ACCEPTOR:-
Mars CashFlow - 4 Channel Dispense
DIMENSIONS:Assembled
2410(w)
x1860(d) x 2340(h)
Monitor Cabinet
Gun/Coin Assembly
Speaker Box Assy
Header Assembly
Joinbox
Pedal Assembly (x2)
1210(w)
1520(w)
1050(w)
1330(w)
500(w)
250(w)
x
x
x
x
x
x
770(d)
540(d)
490(d)
390(d)
490(d)
250(d)
x
x
x
x
x
x
2010(h) x2
1120(h)
180(h) x2
340(h)
230(h)
160(h) x2
WEIGHT:Assembled
557kg
Monitor Cabinet (L)
Monitor Cabinet (R)
Speaker Box (L/R) Assy
Gun/Coin Assembly
Header Assembly
Jointbox
Pedal Assy
210kg
200kg
15kg x2
75kg
20kg
10kg
6kg x2
ACCESSORIES:-
Keys:
(Cash Door) ............... 2
(Coin Door) ................ 2
(Back Door ................. 2
IEC Mains Lead .......................... 1
Link Cable ................................... 1
Operators Manual ....................... 1
Monitor Manual ........................... 1
CashFlow Documents ................ 1
M5 Security Wrench ................... 1
30
2. MAIN COMPONENTS
Starter
Header Assy
Fluorescent lamp
Speaker Box (R) Assy
Speaker Box (L) Assy
Projector mask
Projector Tower (L) Assy
Projector Tower
(R) Assy
Gun Assy
DX Side Pillar
Front Cover
Joint Box Assy
Game PCB Assy
Maintenance Door
Switch Mode
Power Supply
Coin Tower Assy
Gun Tower (R) Assy (2 player)
Pedal Assy
Gun Tower (L) Assy
(1 player)
Base Cover
Control Assy
Cord Box Assy
Back Door
Power cord
31
3. MOVING THE MACHINE
l
l
l
This equipment is fitted with castors to make it easier to move. Take care when
moving the equipment on an inclined floor.
The overall height of this equipment is 2340mm. Take care of any overhead
obstructions. (e.g. Light Fittings, Electric Cables etc.)
Before moving, ensure that the game is seperated into 3 parts: Header Assy,
Monitor Cabinets and Gun/Coin Assy.
4. INSTALLATION
Notes on Installation
l
l
l
NEVER turn the power to the machine ON until installation has been completed
In order to prevent possible electric shocks, be sure that the machine is
connected to the mains supply with a securely connected earthed plug.
So that customers are not injured, ensure that there is at least 500mm
separation between other machines or walls.
In order to avoid damage to the machine due to mis-operation, ensure that the voltage
of the mains supply is 230volts AC.
NOTE
•
If the location site of this machine has a polished floor, it is
recommended that rubber pads are fitted under the level adjusters to
prevent the machine sliding on the floor.
•
In order to gain access to the Power Supply and CPU assemblies,
ensure that the rear of the machine is separated from a wall or other
machine by at least 500mm
Preventing Cross Talk
If machines using the same gun detecting system are installed side by side, cross talk may
occur between them resulting in machine malfunction. If machines of the same type are to
be installed side by side, make sure that they are alternately ‘Frequency Change connector’
installed Game PCB and ‘Frequency Change connector’ not installed Game PCB models.
The ‘Frequency Change Connector’ is fitted to the Player 2 Game PCB.
32

1.
2.
3.
4.
5.
6.
쮕
1.
2.
3.
4.
5.
6.

1.
2.
3.
4.
5.
6.

1.
2.
3.
4.
5.
6.
l
This machine is designed for INDOOR USE ONLY.
Do not install in the following places.
Outdoors
Direct Sunlight, places with excessive humidity or dust, places where there is
water leakage, near air-conditioning or heating equipment, places with
excessive heat or cold temperature.
Places where it would be in the way of emergency exits or fire extinguishing
equipment.
Unstable places or places with excessive vibration.
Places that are not level.
This machine must not be cleaned with a water jet, or installed in an area where
a water jet could be used.
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT. DAS GERÄT DARF AN FOLGENDEN
PLÄTZEN NICHT AUFGESTELLT WERDEN
Im Freien.
In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
In der Nähe von Notausgängen oder Feuerlöschgeräten.
An unstabilen Plätzen oder Plätzen mit übermäßiger Vibration.
An Plätzen, die nicht eben sind.
Diese Maschine darf nicht mit einem Wasserstrahl gereinigt oder in einem Bereich
installiert werden, in dem Wasserstrahlen verwendet werden.
DENNE MASKINE ER KUN DESIGNET TIL INDENDØRSBRUG
INSTALLER IKKE MASKINEN PÅ FØLGENDE STEDER
Udendørs
Direkte sollys, steder med høj fugtighed el. støv, steder med vand udslip, i
nærheden af air-condition eller varme udstyr, steder med usædvanlig høj el. kold
temperatur.
Steder hvor den vil stå i vejen for nødudgange eller brandslukningsudstyr.
Ustabile steder eller steder med for store vibrationer.
Steder der ikke er plane.
Maskinen må ikke renses med en vandstråle eller monteres et sted hvor det er muligt at
bruge en vandstråle.
ESTA MÁQUINA ESTA DISEÑADA ÚNICAMENTE PARA USO EN INTERIORES. NO
INSTALE LA MÁQUINA EN LOS SIGUIENTES LUGARES.
Exteriores.
Bajo luz solar directa, en lugares con polvo o humedad excesiva, lugares donde hay
filtraciones de agua, cerca de aparatos de calefacción o de aire acondicionado, lugares
con temperatura ambiente muy alta o muy baja.
Lugares donde la máquina obstruya salidas de emergencia o equipos de extinción de
incendios.
Suelos inestables o lugares con vibraciones excesivas.
Lugares con suelos no nivelados.
Esta máquina no deberá ser lavada con agua a presión. Tampoco deberá instalarse en
áreas donde puedan haber chorros de agua.
33

1.
2.
3.
4.
5.
6.
ও
1.
2.
3.
4
5.

1.
2.
3.
4.
5.
6.

1.
2.
3.
4.
5.
6.
34
CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR
NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS
A l’extérieur.
Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux,
aux endroits où il y a des risques de fuite d’eau, près de ventilateurs ou source de
chaleur, aux endroits très chauds ou froids.
Dans des zones de proximité des sorties de secours ou d’accès aux équipements
d’extinction du feu.
Dans des emplacements instables ou soumis à de fortes vibrations.
Dans des endroits dénivelés.
Ne nettoyez pas cette machine sous un jet d’eau et ne l’installez pas à un endroit où l’on
risque d’employer des jets d’eau.
TO ΜΗΧΑΝΗΜΑ ΕΙΝΑΙ ΣΧΕΔΙΑΣΜΕΝO ΓΙΑ ΧΡΗΣΗ ΣΕ ΕΣΩΤΕΡΙΚO ΧΩΡO ΜOΝO
ΜΗΝ ΤOΠOΘΕΤΗΣΕΤΕ ΤO ΜΗΧΑΝΗΜΑ ΣΤOΥΣ ΑΚOΛOΥΘOΥΣ ΧΩΡOΥΣ
Εξωτερικά
Απευθείας στον ήλιο,σε μέρη που υπάρχει υγρασία ή σκνη,μέρη που υπάρχει
άφθονο νερ,κοντά σε air-condition ή άλλου είδους θέρμανση,μέρη με υπερβολική
υψηλή ή χαμηλή θερμοκρασία.
Σε μέρη που εμποδίζουν μέσα ανάγκης π.χ. πυροσβεστήρες ή άλλα.
Μη σταθερά μέρη ή μέρη με πολλούς κραδασμούς.
Μέρη που δεν είναι επίπεδα.
QUESTA MACCHINA E’ PROGETTATA PER ESSERE USATA ESCLUSIVAMENTE IN
AMBIENTI INTERNI.NON INSTALLARE LA MACCHINA NEI SEGUENTI LUOGHI.
In ambienti esterni.
Alla luce diretta del sole, in posti con eccesiva umidità o polvere, in luoghi dove ci siano
infiltrazioni d’acqua, vicino ad apparecchi di condizionamento d’aria oppure
riscaldamento, in posti eccessivamente caldi o freddi.
In luoghi dove potrebbe esserci un uscita di emergenza o un’attrezzatura per lo
spegnimento del fuoco.
In posti non stabili o con eccessive vibrazioni.
In luoghi non piani.
La macchina non deve essere pulita con un getto d’acqua, né installata in un’area in cui
si utilizza un getto d’acqua.
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
Utendørs
Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
Ustabile plasser eller plasser med overdreven vibrasjon.
Plasser som ikke er i vater.
La macchina non deve essere pulita con un getto d’acqua, né installata in un’area in cui
si utilizza un getto d’acqua.

1.
2.
Buiten
In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op
plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen
met een zeer hoge of koude temperatuur.
Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd.
Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen.
Op plaatsen die niet vlak zijn.
Deze machine mag niet gereinigd worden met een waterstraal of geïnstalleerd worden op
een plaats waar een waterstraal gebruikt kan worden.
3.
4.
5.
6.

1.
2.
3.
4.
5.
6.

1.
2.
3.
4.
5.
6.
3.
4.
5.
6.
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENASNÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:Exteriores.
`Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
Locais estruturalmente instaveis ou locais com vibrações excessivas.
Locais não nivelados.
Esta máquina não deve sem limpa com jato de água, ou instalada em área na qual
possam ser usados jatos de água.
DENNA MASKIN ÄR AVSEDD ENBART FÖR INOMHUSBRUK
INSTALLERA EJ MASKINEN PÅ FÖLJANDE STÄLLEN
Utomhus
I direkt solsken, platser med extremt hög luftfuktighet eller damm, platser där det
förekommer vattenläckage, nära luftkonditionering eller värmeelement, i extremt hög
eller låg temperatur.
Platser där den skulle kunna vara i vägen för nödutgångar och
brandsläckningsutrustning.
Instabila ställen eller där stark vibration förekommer.
Platser med nivåskillnad.
Denna maskin får inte rengöras med en vatten stråle, eller monterad inom ett område där
en vatten stråle kan användas.

1.
2.
DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN
INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN
TÄMÄ LAITE ON SUUNNITELTU VAIN SISÄKÄYTTÖÖN
ÄLÄ ASENNA LAITETTA SEURAAVIIN PAIKKOIHIN:
Ulkotilaan
Suoraan aurinkovaloon, kosteisiin tai pölyisiin paikkoihin, vesivuotopaikkojen
läheisyyteen, ilmanvaihto- tai lämmityslaitteen lähistölle tai paikkoihin, jossa on erittäin
kuumaa tai kylmää.
Varauloskäytävien, muiden pakoteiden tai tulensammutusvälineiden eteen.
Epävakaisiin tai täriseviin paikkoihin.
Kaltevalle alustalle.
Tätä laitetta ei saa pestä suihkuttamalla sille vettä eikä sijoittaa sellaiseen paikkaan,
missä se voi joutua alttiiksi vesisuihkuille.
35
4-1
Required Dimension for Access (Doors and Passageways)
The machine is separated into the following assemblies for transportation. The size of each
assembly is as follows:
Monitor Cabinet (L)
Monitor Cabinet (R)
Control Assembly
Header Assembly
Jointbox
Pedal Assembly (x2)
1210(w)
1210(w)
1520(w)
1330(w)
500(w)
250(w)
x
x
x
x
x
x
770(d)
770(d)
540(d)
390(d)
290(d)
250(d)
x 2010(h)
x 2010(h)
x 1120(h)
x 340(h)
x 230(h)
x 160(h) (ea)
Weight
Weight
Weight
Weight
Weight
Weight
210kg
200kg
75kg
20kg
6kg
6kg (ea)
If the access route is too low for the machine’s height, the Speaker Box Assy can be
temporarily separated from the Monitor Cabinet to reduce the height to 1860cm.
(See 4-2 page 37)
Furthermore the Projector can be separated from it’s base.
Projector
1140 (W) x 560 (D) x 1,410 (H) mm
Weight: 100 kg
Projector base
1140 (W) x 740 (W) x 920 (H) mm
Weight: 100 kg
For the method of separating the Projector from it’s base, refer to (4-3 page 38.)
390
Signboard Assy
Projector (R) [ (L)] Assy
340
1,330
540
Speaker Box (R)
[ (L)] Assy
Control Assy
1,860
2,010
Joint Assy
500
49
0
1,120
230
Pedal Assy
36
1,5
20
1,2
10
77
0
25
250
0
160
4-2
Separating the Speaker Box
l
The Speaker Box weighs approx 15kg. Ensure that at least two people are used
to remove the Speaker Box.
The fitting position of the speaker box is very high, and it is important that a
safe means of reaching the height safely, without stretching is available. (e.g.
steps, step stool etc.)
1.
Remove 6off Screws (M6x20), remove the Retaining Plates, and lift the Speaker Box
Assy (L) from the Monitor Cabinet (L) ensuring that both ends are supported by the
two people.
2.
Re-assemble in reverse order.
Speaker Box (L) Assy
Screws (M6 x 20)
Screws (M6 x 20)
Retaining Plate
Monitor Cabinet (L) Assy
37
4-3
1.
Fitting the Joint Box
Join the two Monitor Cabinets together at the rear with the supplied Flange socket bolt
(M8x40) and whizz nut (M8).
Monitor Cabinet Assy (L)
(rear side)
Monitor Cabinet Assy (R)
(rear side)
Flange socket bolts (M8 x 40)
Whizz nut (M8)
2.
Fit 2off flange socket bolts (M8x40) to the upper front fixings on the front of the
Projector Cabinets leaving approx 5mm protruding.
Monitor Cabinet Assy (L)
(front side)
Monitor Cabinet Assy (R)
(front side)
Joint Spacer
Monitor Cabinet Assy
Flange socket bolts (M8 x 40)
Approx. 5mm
38
3.
Remove 4off torx screws (M5x12) from the Joint Assy and remove the Joint Cover.
4.
Atach the Joint Assy in place on the Monitor Cabinets and secure with the previously
fitted flange socket bolts (M8x40) and two further supplied flange socket bolts
(M8x40).
5.
Pull out the wiring harnesses from the Monitor Cabinets.
6.
Connect the connectors and Earth connector.
Joint Cover
Torx screws (M5 x 12)
Joint Assy
Flange socket bolts (M8 x 40)
Flange socket bolts (M8 x 40)
Wiring diagram
Earth connector
Connectors
Connectors
CROSS PC board
7.
To disassemble follow the procedure in reverse.
39
4-4
Fitting the Header Assembly
l
The Header Assembly weighs approx 20kg. Ensure that at least two people are
used to fit the Header Assembly.
The fitting position of the Header Assembly is very high, and it is important that
a safe means of reaching the height safely, without stretching is available. (e.g.
steps, step stool etc.)
1.
Loosen only 3off crews (M6x20), with flat and spring washers on both sides of the
Monitor Cabinet top. Slide the Speaker Box Assy (L) to the front, and retighten the 6off
Screws (M6x20), with flat and spring washers, previously loosened
.
2.
Repeat for the Speaker Box Assy (R).
Speaker Box Assy (R)
Speaker Box Assy (L)
Monitor Cabinet Assy (R)
Screws (M6 x 20)
Retaining Plate
Monitor Cabinet Assy (L)
Screw (M6 x 20)
40
3.
Connect the connector from the Monitor Cabinet to the connectors in the sides of the
Speaker Box.
4.
Fit the Header Joint 2 with 2off screws (M6x12)
Connectors
Speaker Box Assy (L)
Header Joint 2
Speaker Box Assy (R)
Screws (M6x12)
5.
Fit the Header Joint from the front of the machine with 2off screws (M6x20)
Header Joint
Screws (M6 x 12)
41
6.
Place the Header onto the Speaker Boxes and connect the Connector.
7.
Ensure that the front of the Header Assy engages in the Header Brackets on the
Speaker Boxes, and secure the Header Assy with 2off screws (M6x12).
Connector
Header Assy
Screws (M6 x 12)
Header bracket
8
42
To remove the Header Assy follow the procedures in reverse.
4-5
1.
Control Assy
Secure the control Assy to the Joint Box with 4off flange socket screws (M8x16).
Harness
Flange socket screws (M8 x 16)
Control Assy (Rear)
Connectors
Connectors
Joint Assy
2.
Withdraw the harnesses from the Monitor Cabinet and the Control Assy.
3.
Connect the nine connectors and one Earth connection. (See diagram below.)
4.
Fit the Joint Cover with 4off torx screws (M5x12).
Earth connector
Control Assy side
monitor Cabinet Assy side
Connectors
Connectors
Connectors
5
Disassemble in reverse order.
43
4-6
Adjusting the Level Adjusters
When the Game is in it’s final position, lower all level adjusters with a spanner so that the
machine is level and all castors are raised from the floor by approx. 5mm. Tighten the Lock
Nut with a spanner to ensure that the level adjusters do not move during game play.
Level adjuster
Castor
44
Approx. 5 mm
4-7
1.
Fitting the Pedal Assy
Connect the Connector and fit, finger tight only, the Pedal Assy with 4off flange socket
screws (M6x12).
Connector
Flange socket screw (M6 x 12)
Control Assy
Flange socket screw (M6 x 12)
Pedal Assy
2.
Push the Pedal Assy flat to the floor, and tighten fully the eight flange socket screws.
(Ensure that there is no space between the Pedal Assy and the floor.)
3.
To remove, follow the installation sequence in reverse.
45
5. OPERATION
l
Should any problem occur, immediately turn the power to the machine OFF until the
problem has been rectified.
Before operating the machine, check that the machine has been installed in
accordance with the instructions and procedures specified in this manual. If the
machine is not installed correctly, fire, electric shock, injury or malfunction may
occur.
Ensure that all warning labels are visible and legible at all times.
To ensure safe operation of the machine, ensure that the pre-service and
maintenance checks have been carried out. Failure to perform the pre-service
maintenance checks could result in unexpected accidents.
5-1
Pre-Service Check
Check the following items before commencing operation.
If any problem is found, rectify the problem before continuing.
5-1-1
Safety Check (before power on)
1.
Is any part of the Mains Cable or plug excessively warm.
2.
All warning labels are attached and legible.
3.
All level adjusters are adjusted properly and the machine is stable.
4.
The Play Zone area is established as specified.
5.
Power cable and Communication cable are routed safely and not liable to cause a
person to trip over them.
6.
Guns are secure and free of any damage.
7
The Jointbox is installed securely to both the Monitor Cabinet and the Control Assy.
8.
Pedal Assemblies are secure. (There must be no space between the Pedal Assy
and the floor.)
9.
Speaker boxes are installed securely to the Monitor Cabinets.
10.
Header Assy is installed securely to the Speaker boxes.
46
5-1-2
Operation Check (after power On)
Turn the power to the machine ON and check the following items.
1.
Does touching the machine give electric shocks.
2.
Is there a smell of burning, abnormal noise or vibration.
3.
Is there any other sign of abnormality or malfunction.
l
Note:
If any of the above occur immediately turn the power to the machine OFF and
disconnect from the power supply until the problem has been rectified.
4.
Check that sound is produced from each speaker.
5.
Check that the fluorescent lamp in the Header Assy is illuminated.
6.
Check that the SIDELED PC board are illuminating. (two LEDs for the Gun Tower
(L) and (R) and two LEDs for the Speakerbox Assys)
7.
Check that the image displayed on the Monitors is correct.
To check the following items press the Service button and play the game.
8.
Check that both Guns are operating correctly.
9.
Check that both Pedal Assys are operating correctly
10.
Check that two players can play in linked mode.
Do not install the machine where spot lamps, direct sunlight or other bright or
flashing lights can reflect on the monitor screens as such lights may prevent the
gun sensors detecting properly.
47
5-2
How to Play
l
If a player becomes unwell due to game images or stimulation by lights, have the person
stop playing the game immediately and let him/her rest.
In rare cases, stimulation by lights or video images can cause a convulsion or loss of
consciousness. If this happens, advice the person to see a doctor for medical
examination as soon as possible. When pre-school children play, request that their
parents or guardians observe the children.
(1) Operation
1. Pressing the pedal: Attack mode : The player can shoot the gun, and can be also
shot by enemies.
2. Releasing the pedal: Hide mode : The player hides behind an item. Enemies’ shots
cannot reach the player.
Releasing the pedal also reloads the hand-gun
with ordinary ammunition.
(2) Game Mode
1. Linked play mode :
The mode allows two players to cooperate in a
game play. In this mode, a player can join in
while a game play is in process.
2. Solo play mode :
This mode is played by a single player. In this
mode, a player cannot join in while a game play
is in process.
* The player can select the game mode on the
Mode Select screen immediately after coin
insertion.
(3) Game rules
1. The player loses one “life” when shot by an enemy.
When the time limit reaches zero, the player also loses one “life.”
The time limit extends when the player destroys all enemies in front of the player,
or receives attacks from enemies.
The game ends when the player has no “life.”
2. The player’s performance level is indicated by the score. The higher the score,
the better the player’s performance.
3. The four weapons can be selected by releasing the pedal and pressing the
trigger.
Weapons have limited ammunition except for the hand-gun, and when the
ammunition runs out, the player cannot use this weapon. When the specified
enemy is shot, the ammunition reloading item will appear.
The demonstration scene inserted between game segments can be skipped by
shooting the gun toward the screen.
48
(4) Event play
The player plays the game following specific event battle rules. The rules are
explained in the game screen for each event. They are roughly categorized into two
types of rules.
1. Multi screen battle event
The player searches and attacks the enemy while changing the screen.
When the muzzle on the screen is pointed toward the desired arrow icon on the
screen, the screen will change to the desired screen. In this event, the barricade
durability is indicated instead of the player’s life. If the barricade durability is
reduced to zero, this event will end and the player’s life decreases by one.
2. Special weapon playing event
The following two weapons can be used.
When a player selects either of the two weapons, he/she cannot replace it with
another weapon in the same event.
A. Special machine gun
Limitless bullets. The machine gun shoots continuously, while the trigger is pressed.
B. Sniper rifle
When the pedal is pressed, the screen zooms toward the target.
When the pedal is released, the ammunition will be reloaded.
49
6. ADJUSTMENTS

쮕



ও






50
l
Adjustment or maintenance on this machine should be carried out by qualified
personnel only.
Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem
Fachpersonal vorgenommen werden.
Justeringer eller vedligehold af denne maskine bør kun udføres af kvalificeret
personale.
Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo por
personal cualificado.
L’installation, le service, le réglage, ou la maintenance doivent être effectués
uniquement par les personnes qualifiées.
Μετατροπές ή επιδιορθώσεις στα μηχανήματα πρέπει να γίνονται μνο απ
εξουσιοδοτημένα άτομα.
Regolazioni e manutenzione su questa macchina devono essere fatti solo da
personale specializzato.
Justering eller vedlikehold på denne maskinen skall bare utføres av kvalifiserte
personell.
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te
worden door bekwaam personeel.
Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente por
pessoal qualificado.
Justeringar och underhåll på denna maskin skall endast utföras av kvalificerad
personal.
Tätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden omaava
henkilökunta.
6-1
Adjustment Switches
The adjustment switches are located inside the Coin Door.
Service switch
Press this switch to increase the credit count without activating the coin counter.
Test switch
Slide this switch to ON to activate the Test mode.
The Test mode is used to change the game price and perform various tests.
(See 6-2 page 52)
Select switch
An item in the Test mode is selected by operating this switch up or down.
Enter switch
After an item is selected by using the Select switch, press the Enter switch to finalize
the selection or to execute the selected item.
51
6-2
Test Mode
Do not enter Test if two games are being played in Linked mode. Turning on the
Test switch of one unit will cause the other players game to return to the beginning
of the game and play conditions to be initialized. (score, weapon, ammunition, life
and level)
1.
Open the Coin Door and slide the respective Test switch ON. The following Menu
screen will be displayed.
(a) Setting inconsistency warning indication (If the machine is functioning
normally, these indications will not appear.)
MENU
COIN OPTIONS <--L/R:NOT THE SAME
GAME OPTIONS <--L/R:NOT THE SAME
I/O TEST
MONITOR TEST
SOUND TEST
BOOKKEEPING
OTHERS
<--L/R:NOT THE SAME
Coin Options
See 7-2-1
Game Options
See 7-2-2
I/O Test
See 7-2-3
Monitor Test
See 7-2-4
Sound Test
See 7-2-5
Book keeping
See 7-2-6
PCB test, Back up memory
initialization, etc.
LINK MALFUNCTION 1 2 3
The internal battery01 is dead.
The internal battery02 is dead.
SELECT SW:CHOOSE ENTER SW:ENTER
See 7-2-7
(b) Link play error warning
(c) Rack Assy, Dead internal battery warning
(This indication appears when the internal
battery is dead.)
MENU screen
Note:
52
Operate the Select switch Up or Down to step through the items available, the
selected item will blink.
Press the Enter button to enter the selected item.
When the adjustment has been made, select EXIT and press the Enter switch. The
display will return to the Menu screen.
When all adjustments are completed, slide the Test switch to OFF. The screen will
return to the Game mode.
If settings are not correct, the error messages including (a), (b) and (c) shown
will be displayed.
(a) Setting inconsistency warning indication
When player 1 and player 2 game parameters are inconsistent, the following message will
be displayed. Check and set the correct game parameters again.
Setting inconsistency warning items
COIN OPTION
GAME OPTIONS
OTHERS
GAME COST
CONTINUE COST
FREE PLAY
PLAYER'S LIFE
DIFFICULTY
HIT-COLOR
LANGUAGE
ATTRACT CUT
(b) Link play error warning
This message will appear if the link play mode indicates failure.
The game will run improperly while the error message is being indicated.
The message on the right of the screen indicates the type of error.
If “1” or “2” is indicated, possible error cause is circuit board malfunction (Game PC
Port or NA-JV PC Board). (See 7-11 Game PCB Assy replacement, page 84)
If “3” is indicated, inconsistency exists between right and left players’ software version.
Indication
Description
ON
Normal
OFF*
Communication settings are not made, or data is not received.
NG*
Unknown data is received
(c) Dead internal battery warning
If this warning indication appears, turn off the power switch and wait for about 10
minutes.
Then, turn on the power switch and check the MENU screen in the Test mode to see if
the same warning indication appears again.
If the warning indication appears even though the above procedure is repeated two or
three times, the internal battery capacity may be low or the Game PC Board may be
defective.
53
6-2-1 Coin Options
This screen is used to set the price of play and free play settings.
1.
Select ‘COIN OPTIONS’ on the Menu screen, and press the Enter button. The
following screen will be displayed.
COIN OPTIONS
[DEFAULT IN GREEN]
GAME COST
CONTINUE COST
1 COIN(S)
1 COIN(S)
FREE PLAY
NO
1 CREDIT
1 CREDIT
(a)
(b)
(c)
EXIT
SELECT SW: CHOOSE
ENTER SW: ENTER
2.
Use the Select switch to choose an item to be changed. The selected item is
indicated in red.
3.
Press the Enter Button to continue.
4.
Use the Select switch to change the setting.
5.
After the setting has been changed, press the Enter button to return to the selection
screen.
6.
When all adjustments have been made, select EXIT and press the Enter button to
return to the Menu screen.
Item
Description
Default Setting
(a) Game price setting
Number of coins required for one game play
1 coin to 9 coins
1
(b) Continue game price setting *1
Number of coins required for one continue
game play - 1 coin to 9 coins
1
(c) Free play setting *2
No (Disabled)
YES (Enabled)
*1
*2
Note:
54
NO
The number of coins for the continue game price cannot be set higher than the
number of coins set for Game price. When increasing both Game and Continue
game prices, increase the Game price first.
When the Free Play setting is set to ‘YES’, the game starts when the pedal is
depressed.
The price of play on this game is set within the Cashflow Coin Mech.
Ensure that the Game Cost is set to: 1 COIN(S) 1 CREDIT
6-2-2 Game Options
This screen is used to set the game options.
1.
Select ‘GAME OPTIONS’ on the Menu screen, and press the Enter button. The
following screen will be displayed.
GAME OPTIONS
[DEFAULT IN GREEN]
}
LINK
: ON 2
LINK AS : 1
(LEFT)
PLAYER’S LIFE
DIFFICULTY
HIT COLOUR
HI-SCORE INIT
3
C (MEDIUM)
RED
(a)
(b)
(c)
(d)
(e)
EXIT
SELECT SW: CHOOSE
ENTER SW: ENTER
2.
Use the Select switch to choose an item to be changed. The selected item is
indicated in red.
3.
Press the Enter Button to continue.
4.
Use the Select switch to change the setting.
5.
After the setting has been changed, press the Enter button to return to the selection
screen.
6.
When all adjustments have been made, select EXIT and press the Enter button to
return to the Menu screen.
Note:
If the difficulty level setting (c) is not the same for both Player 1 and Player 2, the
game will not operate correctly.
Ensure that the difficulty level is the same for both Player 1 and Player 2.
Item
Description
Default Setting
(a) Communication status indication See ’7-2-3 I/O Test’ page 54
(b) Player’s LIFE setting
Number of Lives at game start - 1~9
(c) Difficulty level setting
A (VERY EASY)
B (EASY)
C (MEDIUM)
D (HARD)
E (VERY HARD)
(d) Hit colour setting
RED/GREEN
(e) High score initialize
When this item is selected and entered, the
screen displays "HIGH SCORE INITIALIZE ?"
and prompts for input "YES" or "NO."
NO: Returns to the screen displayed prior to
the "HI-SCORE INITIALIZE" message.
YES: Initializes the high score data.
3
C (MEDIUM)
RED
55
6-2-3 I/O Test
This screen is used to set the game options.
1.
Select ‘GAME OPTIONS’ on the Menu screen, and press the Enter button. The
following screen will be displayed.
I/O TEST
DIP
LINK
LINK AS
: 1234
: ON
:1
[ON : RED]
[LEFT]
(a)
}
(b)
I/O PCB CHECK
GUN INITIALIZE
SWITCH TEST
SOLENOID TEST
LED TEST
(c)
(d)
(e)
(f)
(g)
EXIT
SELECT SW: CHOOSE
ENTER SW: ENTER
2.
Use the Select switch to choose an item to be changed. The selected item is
indicated in red.
3.
Press the Enter Button to continue. The selected test screen will be displayed.
4.
When all tests have been made, select EXIT and press the Enter button to return to
the Menu screen.
(a) DIP Switch Settings
Displays the setting of the DIP switches. Switches set to ON will be shown in red.
All DIP switches should be set to OFF
(b) Link Check
Indicates the communication status between Player 1 and Player 2
LINK AS:
1 (LEFT) - The screen on the left
2 (RIGHT) - The screen is on the right.
§
If ‘LINK OFF’ or ‘LINK NG’ is indicated, the game will not operate correctly.
(c)
(d)
(e)
(f)
(g)
Indicates condition of the I/O PC board.
Used to Initialize the gun sighting.
Used to test game switches.
Used to test the gun recoil solenoid.
Used to test the Display LEDs.
56
(see 6-2-3-1 page 57)
(see 6-2-3-2 page 58)
(see 6-2-3-3 page 61)
(see 6-2-3-4 page 62)
(see 6-2-3-5 page 63)
6-2-3-1
I/O PCB Check
This screen is used to check the I/O PC board, and to display the software version
number.
1.
Select ‘I/O PCB CHECK’ on the I/O Test Menu screen, and press the Enter button.
The following screen will be displayed.
I/O TEST
DIP
LINK
LINK AS
: 1234
: ON
:1
[ON : RED]
[LEFT]
I/O PCB CHECK : Connect OK
namco ltd. ;NA-JV; ver1.00;JPN
Multipurpose
EXIT
SELECT SW: CHOOSE
2
ENTER SW: ENTER
Press the Enter button to return to the I/O Test Menu Screen.
Note: There are no adjustments available on this screen.
57
6-2-3-2
Gun Initialize
This screen is used to adjust the gun sight.
1.
Select ‘GUN INITIALIZE’ on the I/O Test Menu screen, and press the Enter button,
or slide the Test switch ON ` while pressing the Enter button. The following screen
will be displayed.
GUN INITIALIZE
+OUT OF SCREEN+
(a)
(Gun Cross)
This indication appears
when the gun is aimed
AIM AT SCREEN
TO CHECK GUN ACCURACY
toward the scren,
PUSH SERVICE SW : ADJUST GUN SIGHT
ENTER SW : EXIT
GUN INITIALIZE screen (1)
2.
The Gun Assy’s sighting can be checked on the above screen.
When the gun is aimed at the screen, the gunsight (crosshairs) will appear on the
screen.
Ensure that the gun is aimed within the rectangle and that the sight is in the correct
position. (Check all areas of the screen.)
When the gun is aimed outside of the rectangle, the ‘OUT OF SCREEN’ message
should be displayed at position (a).
If the ‘OUT OF SCREEN’ message frequently appears even though the gun is
aimed within the rectangle check the following:
•
Bright light shining or reflecting on the LEDs around the screen.
•
Gun Assy too close to the screen. (less than 60cm)
•
The gun is at too great an angle to the screen.
Either move the machine or reduce the lighting and aim with the correct distance and
angle. If the problem still persists or if the gun sight (crosshair) is not displayed in the
correct position, continue with the following:
58
3.
Press the Service button, or step on the pedal, while GUN INITALIZE ! screen is
displayed. The following GUN INITIALIZE 2 screen will bve displayed.
1
2
3
4
AIM AT CENTRE OF THE CROSS
AND PULL GUN TRIGGER
5
6
7
8
GUN INITIALIZE screen (2)
The gun sight adjustment is made by aiming and pulling the trigger at eight targets
(four targets each at top and bottom of the screen.)
Aim the gun at the centre of each target that is displayed and pull the trigger. Each
time the trigger is pulled the next target will be displayed on the screen in the order
shown above. After the eighth target is shot, the GUN INITIALIZE 1 screen will
appear to confirm aiming.
4.
When adjustment is completed press the Enter button to return to the I/O Test
Menu Screen.
59
When adjusting the gun sight, follow the procedures below
•
•
•
•
Hold the gun Assy toward the screen so that the top edge of the rear site of the gun
aligns with the horizontal line of the crosshairs (+) on the screen.
Bring the top edge of the front site at the tip of the Gun Assy so that it also aligns with
the horizontal line of the crosshairs (+) on the screen.
Make sure that the centre of the rear sight and the centre of the front sight are at the
centre of the crosshairs (+), and shoot the Gun Assy.
Be sure to hold the Gun Assy straight. Do not tilt the Gun Assy.
Both front and rear sights
must be aligned on a straight line.
60
6-2-3-3
Switch Test
This screen is used to test the game switches.
1.
Select ‘SWITCH TEST’ on the I/O TEST Menu screen, and press the Enter button.
The following screen will be displayed.
I/O TEST
DIP
:1234
LINK
:ON
LINK AS
:1
SWITCH TEST
COIN
SERVICE
TEST
UP SELECT
DOWN SELECT
ENTER
GUN TRIGGER
FOOT PEDAL
SENSOR
[ON:RED]
(LEFT)
0
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
UP SELECT SW + ENTER SW:EXIT
SWITCH TEST screen
2.
When a switch is pressed, the corresponding display on the screen will change.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
3.
The displayed number will increment each time sufficient coins for a credit are
inserted through the Cashflow.
Changes to ON each time the Service button is pressed.
This will always display ON as the game is in test.
Changes to ON each time the Select switch is pushed Up.
Changes to ON each time the Select switch is pushed Down.
Changes to ON each time the Enter button is pressed.
Changes to ON each time the Gun Trigger is pulled.
Changes to ON each time the Pedal is depressed.
Changes to ON each time the Gun Assy is aimed at the screen.
When testing is complete, press the Enter button while holding the Select switch UP
to return to the I/O Test Menu screen.
61
6-2-3-4
Solenoid Test
This screen is used to test the Gun Assy’s recoil mechanism.
1.
Select ‘SOLENOID TEST’ on the I/O TEST Menu screen, and press the Enter
button. The following screen will be displayed.
I/O TEST
: 1234
: ON
: 1
DIP
LINK
LINK AS
[ON:RED]
(LEFT)
SOLENOID TEST
PULL GUN TRIGGER TO ACTION
EXIT
SELECT SW: CHOOSE
ENTER SW:ENTER
SOLENOID TEST screen
2.
The Gun Assy’s Solenoid will operate each time the trigger is pulled.
3.
Select ‘EXIT’ and press the Enter button to return to the I/O Test Menu screen.
62
6-2-3-5
LED Test
This screen is used to test the Side LED PC board.
1.
Select ‘LED TEST’ on the I/O TEST Menu screen, and press the Enter button. The
following screen will be displayed.
DIP
LINK
LINK AS
I/O TEST
: 1234
: ON
: 1
[ON:RED]
(LEFT)
LED TEST
ALL
LED (MAIN SP)
LED (GUN TOWER)
LED (VOICE SP)
(a)
(b)
(c)
(d)
OFF
OFF
OFF
OFF
EXIT
SELECT SW: CHOOSE
ENTER SW:ENTER
LED TEST screen
2.
Use the Select switch to choose an item to be checked. The selected item is
indicated in red.
3.
Press the Enter Button to continue.
4.
Use the Select switch to turn the LEDs On or OFF.
Indication
Status
(a) ALL
Turn all LEDs ON or OFF.
(b) LED (Main SP)
Turn the main speaker assy’s LEDs located on the upper part of
the Monitor Cabinet ON or OFF.
(c) LED (GUN TOWER)
Turn the LEDs located on the front acrylic panel of the Gun Tower
Assy ON or OFF.
(d) LED (VOICE SP)
Turn the speaker assy’s LEDs located on the upper part of the Gun
Tower assy ON or OFF.
5.
When all testing has been completed, select EXIT and press the Enter button to
return to the I/O Test Menu screen.
63
6-2-4 Monitor Test
This screen is used for monitor adjustments.
1.
Select ‘MONITOR TEST’ on the TEST Menu screen, and press the Enter button.
The following screen will be displayed.
MONITOR TEST
GRADATION PATTERN
(a)
CROSSHATCH PATTERN
(b)
VIEW ANGLE ADJUST
(c)
FULL WHITE
(d)
EXIT
SELECT SW: CHOOSE
ENTER SW:ENTER
MONITOR TEST screen
2.
Use the Select switch to choose an item to be changed. The selected item blinks.
3.
Press the Enter Button to display the selected pattern.
(Pressing the Enter button again will return to the above Monitor Test screen)
4.
When all adjustments have been made, select EXIT and press the Enter button to
return to the Test Menu screen.
Indication
Status
(a) Gradation Pattern
Displays graduated colour bars for colour set-up
(b) Crosshatch Pattern
Displays a crosshatch for geometry set-up
(c) View Angle Adjust
Displays a white border for picture size set-up
(d) Full white
Displays a white screen for brightness / contrast set-up
64
6-2-5 Sound Test
This screen is used to set the sound level and to test the stereo sound reproduction.
1.
Select ‘SOUND TEST’ on the Menu screen, and press the Enter button. The
following screen will be displayed.
SOUND TEST
[DEFAULT IN GREEN]
VOLUME
GAME
ATTRACT
OUTPUT LEVEL
REQUEST SONG
MESSAGE:
EXIT
[0~15] 6
[0~15] 4
LEFT
70
RIGHT 70
VOICE 90
(a)
(b)
NO. 000
(d)
(e)
SELECT SW : CHOOSE
SERVICE SW : REQUEST
(c)
ENTER SW: ENTER
ON /OFF
SOUND TEST screen
2.
Use the Select switch to choose an item to be changed. The selected item is
indicated in red.
3.
Press the Enter Button to continue.
4.
Use the Select switch to change the setting.
When item (d) is selected, each time the Enter button is pressed, the adjustment
digit changes. Use the Select switch to change the value of each digit to set a
desired number. When the Service button is pressed, the music or sound effect of
the selected number will be reproduced.
When ‘000’ is selected and the Service button pressed, sound will be produced by
the left speaker, right speaker, voice speaker and woofer in that order. The volume
reference (‘GAME’ or ‘ATTRACT’) and the present sound reproduction
‘LEFT’.,’RIGHT’, ‘VOICE’ or ‘WOOFER’ will be displayed at position (e).
5.
When all adjustments have been made, select EXIT and press the Enter button to
return to the Menu screen.
65
6-2-6 Bookkeeping
This screen is used to view various game data.
1.
Select ‘BOOKKEEPING’ on the Menu screen, and press the Enter button.
2.
Displayed game data cannot be reset in this screen. To clear data execute
‘INITIALIZE’ or ‘BACK-UP MEMORY’
3.
After checking the game data select ‘EXIT’ and press the Enter button to return to
the Test Menu screen.
66
6-2-7 Others
This screen is used to set language and initialize back-up memory.
1.
Select ‘OTHERS’ on the Menu screen, and press the Enter button. The following
screen is displayed.
OTHERS
[DEFAULT IN GREEN]
ROM1 TSF100-1-NA-MPR0-A03
03 / 31 / 2006 FRI 16 : 12 : 03
ROM2 TSF100-1-NA-HDD0-AOO
03 / 30 / 2006 THU 14 : 28 : 10
CLOCK
08 / 31 / 2006 THU
S/N
000000-123456
LANGUAGE
ENG
ATTRACT CUT
OFF
DRIVE CHECK
BACKUP MEMORY INITIALIZE
(a)
(b)
23 : 11 : 12
(c)
(d)
(e)
(f)
(g)
(h)
EXIT
SELECT SW : CHOOSE
ENTER SW: ENTER
OTHERS screen
2.
Use the Select switch to choose an item to be changed. The selected item is
indicated in red.
3.
Press the Enter Button to continue.
4.
Use the Select switch to change the setting. Pressing the Enter switch returns to
the selection menu screen.
5.
When all adjustments have been made, select EXIT and press the Enter button to
return to the Menu screen.
(a)
(b)
(c)
(d)
(e)
(f)
Displays the version of ROM 1 which contains the program.
Displays the version of ROM 2 which contains data.
Displays the current time set in the internal clock.
Display the software serial number.
Sets the on screen language.
The default setting is ‘OFF’. If ‘ON’ is selected, violent scenes will be skipped during
the attract mode.
Checks data saved in the HDD. (This item is not used in normal operation).
Initializes back-up memory.
Selecting ‘YES’ and then pressing the Enter button clears the gun sight setting, high
score date, play data and other variables, and then returns the game to its default
condition.
(g)
(h)
Note:
If the software versions displayed at (a) and (b) are different in TEST mode for
player 1 and player 2, the game will not function correctly.
67
7. MAINTENANCE

쮕



ও


68
Adjustment or maintenance on this machine should be carried out by qualified
personnel only.
Ensure that the POWER to the machine is turned OFF before commencing any
maintenance work. (Trouble shooting, service or repairs etc.)
Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem
Fachpersonal vorgenommen werden.
Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der
Netzstecker gezogen werden.
Justeringer eller vedligehold af denne maskine bør kun udføres af kvalificeret
personale.
Sørg for, at strømmen til maskinen er slukket før der foretages nogen form for
arbejde (fejlfinding, reparation etc.)
Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo por
personal cualificado.
Asegúrese de que la máquina está desconectada antes de comenzar cualquier
trabajo de mantenimiento (reparaciones, resolución de problemas, etc.)
L’installation, le service, le réglage, ou la maintenance doivent être effectués
uniquement par les personnes qualifiées.
S’assurer que l’interrupteur soit sor OFF avant de commencer tout travail de
maintenance (localisation d’une panne, rèparations, etc.)
Μετατροπές ή επιδιορθώσεις στα μηχανήματα πρέπει να γίνονται μνο απ
εξουσιοδοτημένα άτομα.
Να είναι σίγουρα κλειστ το ρεύμα πριν οποιαδήποτε δουλειά στο μηχάνημα.
Regolazioni e manutenzione su questa macchina devono essere fatti solo da
personale specializzato.
Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro
di manutenzione (guasti, riparazioni etc.)
Justering eller vedlikehold på denne maskinen skall bare utføres av kvalifiserte
personell.
Forsikre deg om at strømmen er slått av før du påbegynner noe som helst
vedlikeholdsarbeid (feilsøking, reparasjon osv.)




Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te
worden door bekwaam personeel.
Zorg ervoor dat de machine UITgeschakeld is voordat er enig onderhoudswerk
wordt verricht (troubleshooting, reparaties etc.)
Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente por
pessoal qualificado.
Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer
tipo de trabalho de manutenção. (identifação de avarias, reparação etc.)
Justeringar och underhåll på denna maskin skall endast utföras av kvalificerad
personal.
Försäkra dig om att strömmen är avstängd innan underhållsarbete påbörjas
(felsökning, reparationer etc.)
Tätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden omaava
henkilökunta.
Varmista, että laite on kytketty POIS PÄÄLTÄ ennen työn aloittamista.
69
7-1
Cleaning
Do not use organic solvents such as thinners or petroleum. They can cause
deterioration of the material surfaces.
To clean the machine, wipe with a dry soft cloth. If the unit is extremely dirty, use a soft cloth
dampened with a neutral detergent to remove the dirt, and then rub lightly with a cloth
dampened slightly with water. Finally, wipe thoroughly dry with a soft cloth.
7-1-1
Cleaning the Gun Assy
Clean the tip of the barrel everyday to maintain gun accuracy. Use a clean soft cloth to
wipe the tip of the barrel.
•
Do not use detergents or chemicals for cleaning.
•
Be careful not to damage the tip of the barrel.
Tip of gun barrel
7-1-2
Cleaning the Front Acrylic Cover
Clean the following sensor section’s filters (20 locations) on the Monitor Mask everyday to
maintain gun accuracy. Clean the filter on the LED board with a soft cloth to prevent
scratching the surface. Scratches on the monitor mask can affect the Gun Assy detection
performance.
Filter (20 locations)
Monitor mask
70
7-2
Regular Maintenance
The following should be conducted at least once every six months.
7-2-1
1.
Greasing the Pedal Plunger
Remove 4off flange socket screws (M6x12) from the Pedal Assy. Withdraw the
Pedal Assy only sufficient to disconnect the connector. Disconnect the connector
and remove the Pedal Assy.
Control Assy
Connector
Flange socket screw
(M6 x 12)
Flange socket screw
(M6 x 12)
Pedal Assy
2.
Remove 4off Torx screws (M5x12) and remove the Cover (M).
Torx screw (M5 x 12)
Torx screw (M5 x 12)
Cover (M)
71
3.
Remove 4off whizz nuts (M4) retaining the Holder. While holding the Plunger in,
remove the holder with plunger.
Note:The plunger is spring loaded, take care that the plunger and spring do not fly
off.
4.
Wipe away any old grease from the Plunger and Plate surface on the Pedal.
5.
Apply a light grease to the Plate and spherical surface of the Plunger.
Microswitch
Whizz nut (M4)
Holder
Plunger
Whizz nut (M4)
Plate
Gease Here
6.
Reassemble in reverse.
Note: After reassembly, check the operation of the Pedal Assy.
(see 6-2-3-3 page 61)
72
7-2-2
1.
Checking the Plunger for Wear
Remove 4off Torx screws (M5x12) and remove the cover (M)
Torx screw (M5 x 12)
Torx screw (M5 x 12)
Cover (M)
2.
Depress the Pedal by hand and visually check that the Plunger operates the Micro
Switch.
Microswitch
pedal
released
Foot plate
Whizz nut
Pedal
pressed
Plunger
3.
If the Plunger is worn and does not operate the Micro Switch, replace the Plunger.
4.
Reassemble in reverse.
73
7-3
Removing the Monitor Mask
1.
Remove the Header, Header Joint, Header Joint 2 and disconnect the connector. (see
4-4 (3~8) page 41)
2.
Separate the two Monitor Cabinets and separate the Monitor Cabinet from the Joint
Assy (see 4-3 page 38)
3.
Remove 2off tork screws (M5x25), undo the lock and remove the Front Door.
Torx screw (M5 x 25)
Unlock
Front panel
74
4
Remove 4off pozi head screws (M5x35) and remove the Front Side Panel.
Pozi head screws
(M5x35)
Front Side Panel
Pozi head screws
(M5x35)
5.
Remove 4off pozi head screws (M5x25) and remove the Upper or Lower Monitor
Mask.
Pozi head screws (M5 x 25)
Upper Monitor Mask
Pozi head screw
(M5 x 25)
Pozi head screw
(M5 x 25)
Pozi head screw
(M5 x 25)
Pozi head screw
(M5 x 25)
Lower Monitor Mask
Pozi head screws (M5 x 25)
6.
Reassemble in reverse order.
75
7-4
Replacing the LED Board
•
The LED Board can be damaged by static electricity.
Before handling the LED Boards, always touch an earthed metal surface to
discharge any static electricity.
•
If the two LEDs (red spots) under the Monitor Mask’s filter (see illustration below) do
not illuminate, the LED board may be defective or malfunctioning.
As any defective LED Board will prevent the proper functioning of the game, replace
the defective LED Board as soon as possible.
1.
Remove the Monitor Mask. (see 7-3 page 74)
2.
Disconnect the LED Board’s two connectors, remove 2off whizz nuts (M3), and remove
the defective LED Board.
Monitor mask (Rear side)
LEDs (red spots)
Connector
LED Board
(Take note of the direction.)
OUT indication
Filter
IN indication
Whizz nut (M3)
3.
Note:
76
Reassemble in reverse order.
Ensure that the LED Board is the correct way round.
Connector
7-5
Replacing the Game PCB Assy
•
The Game PCB Assy can be damaged by static electricity.
Before handling the Game PCB Assy, always touch an earthed metal surface to
discharge any static electricity.
1.
Remove the Front door. (see 7-3 page 74)
2.
Disconnect the four connectors, and remove 1off pozi head screw (M4x6) to remove
the Earth terminal.
3.
Remove 4off nuts (M6) and spring washers, and remove the Game PCB Assy.
Nuts (M6)
Rack Assy
Nuts (M6)
Connector
Earth terminal
Control Board Assy
4.
Spring washers
(M6)
Connector (Red)
Connector (White)
Connector (Yellow)
Pozi head screw
(M4 x 6)
Reassemble in reverse order.
77
7-6
Replacing the Amp PC Board
•
The Amp PC Board can be damaged by static electricity.
Before handling the AMP Board, always touch an earthed metal surface to
discharge any static electricity.
1.
Remove the Front door. (see 7-3 page 74)
2.
Disconnect the five connectors. Remove 5off pozi head screws (M3x6), with flat and
spring washers, and remove the Amp PC Board.
Connector
Pozi head screw (M3 x 6)
(with both flat and spring washers)
Pozi head screw
(M3 x 6)
(with both flat and
spring washers)
AMP PC board
Connector (yellow)
Connector
3.
78
Reassemble in reverse order.
Connector (red)
Connector (white)
7-7
Replacing the SIDELED PC Board (Header Assy)
•
•
1.
The SIDELED PC Board can be damaged by static electricity.
Before handling the SIDELED Board, always touch an earthed metal surface to
discharge any static electricity.
The red colour seal is affixed to the SIDELED (R) PC Board. The blue colour seal
is affixed to the SIDELED (B) PC Board.
Remove the Panel washer and countersunk flat head screws(M5x8) and remove the
Header LED Acrylic.
Speaker Box (L) Assy
Header LED Acrylicl
Panel washer
Countersunk flat head screw (M5 x 8)
2.
Remove 3off cap screws (M5x12), disconnect the connector, and remove the Top
Braid.
Speaker Box (L) Assy
Cap screw (M5 x 12)
Sign board Assy
DX top braid
DX Speaker Cover
Connector
79
3.
Remove 2off cap screws (M4x6), and remove the LED Bracket
4.
Remove 3off pozihead screws (M3x6), with flat and spring washers. Disconnect the
connector and remove the SIDELED PC Board from the LED bracket.
Harness
Pozi head screw (M3 x 6)
(with both flat and spring washers)
LED bracket
Connector
SIDELED (R) PC board
(for player 2, SIDELED (B) PC board).
Cap screw (M4 x 6)
DX top braid
5.
80
Reassemble in reverse order.
7-8
Replacing the Fluorescent Tube / Starter
•
•
The fluorescent lamp may be hot. Take care when removing the fluorescent
lamp.
Take care when replacing the fluorescent lamp or starter, as the work must be
conducted at height.
1
Remove six off countersunk flat head screws (M5x8), 6off panel washers, and remove
the Header Panel.
2.
Replace the Fluorescent Tube and/or Starter.
Countersunk flat head screws (M5 x 8)
Panel washers
Countersunk flat head screws (M5 x 8)
Panel washers
Header panel
Header Assy
Starter
3.
Fluorescent lamp
Reassemble in reverse order.
81
7- 9 Removing the Control Panel
1.
Remove 6off torx screws (M5x20).
2.
Raise the Control Panel only sufficient to access the connectors.
3.
Disconnect the connectors and remove the Control Panel.
Control panel
Torx screw (M5 x 20)
Connector
Torx screw (M5 x 20)
4.
82
Reassemble in reverse order.
7-10 Replacing the SIDELED PC Board
7-10-1 (Control Panel)
• The SIDELED PC Board can be damaged by static electricity.
Before handling the SIDELED PC Board, always touch an earthed metal surface
to discharge any static electricity.
• The red colour seal is affixed to the SIDELED (R) PC Board’s connector. The blue
colour seal is affixed to the SIDELED (B) PC Board’s connector.
1.
Remove the Control Panel. (see 7-9 page 82)
2.
Remove 3off pozi head screws (M3x6), with flat and spring washers, and then remove
the SIDELED PC Board.
Pozi head screws (M3 x 6)
(with flat and spring washers)
Connector
Control panel
SIDELED (R) PC board
(For the player 2 Gun Tower,
SIDELED (B) PC board.)
3.
Reassemble in reverse order.
83
7-10-2
(Gun Assy)
• The SIDELED PC Board can be damaged by static electricity.
Before handling the SIDELED PC Board, always touch an earthed metal surface
to discharge any static electricity.
• The red colour seal is affixed to the SIDELED (R) PC Board’s connector. The blue
colour seal is affixed to the SIDELED (B) PC Board’s connector.
1.
Remove the Control Panel. (see 7-9 page 82)
2.
Disconnect one connector and remove 2off cap screws (M4x6). Then remove the
Tower LED Bracket.
3.
Remove 3off pozi head screws (M3x6), with flat and spring washers, and remove the
SIDELED PC Board.
Cap screw (M4 x 6)
Tower LED bracket
Connector
SIDELED (R) PC board
(For the player 2 Gun Tower,
SIDELED (B) PC board.)
pozi head screws (M3 x 6)
(with both flat and spring washers)
4.
84
Reassemble in reverse order.
Tower LED bracket
7-11 Replacing the NA-JV Board Assy
•
The NA-JV Board can be damaged by static electricity.
Before handling the NA-JV Boards, always touch an earthed metal surface to
discharge any static electricity.
1.
Remove the Control Panel. (see 7-9 page 82)
2.
Disconnect the four connectors and remove 4off pozi head screws (M4x6). Remove
the NA-JV PC Board together with the PCB Base.
Pozi head screw
(M4x6)
Pozi head screw
(M4x6)
NA-JV PC Board
3.
Note:
Reassemble in reverse order.
After reassembly, check the operation of the NA-JV PC Board.
(see 6-2-3-1 page 57)
85
7-12 Replacing the CPU Board
• The CPU Board can be damaged by static electricity.
Before handling the CPU Board, always touch an earthed metal surface to
discharge any static electricity.
1.
Remove the Control Panel. (see 7-9 page 82)
2.
Remove the NA-JV PC Board Assy. (see 7-11 page 85)
3.
Disconnect the four connectors from the CPUBoard. (For player 2 also remove the
Frequency Changeover Connector.)
Frequency changeover harness
(player 2 only)
CPU board
Connectors
Frequency changeover connector
NA-JV PC Board
86
4.
Remove 4off Whizz nut (M3) and remove the CPU Board.
Whizz nut (M3)
CPU board
1
2
ON
Dip switch
Whizz nut (M3)
5.
Reassemble in reverse order.
•
It is important that the Dip Switches are set correctly for STD an DX versions of
this game.
The settings should be:
STD Sw 1 ON
Sw 2 OFF
DX
Sw 1 ON
Sw 2 ON
•
After replacing the CPU Board, be sure to Initialize the Guns.
(see 6-2-3-2 page 58)
•
If the player 2’s CPU Board has been replaced, ensure that the Frequency
Changeover Connector has been refitted. If this connector is not fitted, the gun
assy detection system may be confused with the player 1 CPU Board and the
game will fail to operate correctly.
87
7-13 Replacing the CROSS PC Board
• The CROSS PC Board can be damaged by static electricity.
Before handling the CROSS PC Board, always touch an earthed metal surface to
discharge any static electricity.
1.
Remove the 4off torx screws (M5x12) and remove the Joint Cover.
2.
Disconnect the two connectors, remove 4off pozi heads screws (M3x6), with flat and
spring washers, and remove the CROSS PC Board.
Torx screw (M5 x 12)
Joint cover
Torx screw (M5 x 12)
Pozi head screw (M3 x 6)
(with both flat and spring washers)
Joint Assy
CROSS PC board
3.
Note:
88
Connector
Reassemble in reverse order.
After reassembly, check the communication condition (see 6-2-3 page 56)
7-14 Replacing the Gun Assy
1.
Remove the Control Panel (see 7-9 page 82)
2.
Remove 2off whizz nuts (M6) that secures the Gun Assy from the rear of the Control
Panel.
3.
Pull up and remove the Connector Cover and remove the Gun Assy
Gun Assy
Connector cover
Control panel
Connector
Whizz nut (M6)
4.
Reassemble in reverse order.
•
After replacing the Gun Assy, be sure to Initialize the Guns.
(see 6-2-3-2 page 58)
89
7-15 Replacing the Gun Slides (L & R)
1
Remove the Gun Assy. (see 7-14 page 89)
2.
Remove 5off button head screws (M3x8) and remove the Slide (L) and Slide (R).
Slide (L)
Button-head screwss (M3 x 8)
Slide (R)
Button-head screws (M3 x 8)
3.
Reassemble in reverse order.
•
After replacing the Gun slides, be sure to Initialize the Guns.
(see 6-2-3-2 page 58)
90
7-16 Separating The Gun Body
1.
Remove the Gun Sides (L & R). (see 7-14 page 89)
2.
Lay the Gun Body on it’s left side.
3.
Remove 6off button head screws (M3x6) and remove the Gun Body (R).
Gun body (L)
Light receiving unit
Button-head screw (M3 x 8)
Gun body (R)
Button-head screw (M3 x 8)
Button-head screw (M3 x 8)
4.
Reassemble in reverse order.
•
After replacing the Gun Body, be sure to Initialize the Guns.
(see 6-2-3-2 page 58)
91
7-17 Replacing the Gun Light Receiving Unit
• The Light Receiving Unit can be damaged by static electricity.
Before handling the Light Receiving Unit, always touch an earthed metal surface
to discharge any static electricity.
• Do not disassemble the Light Receiving Unit . Do not touch the knob on the
Light Receiving Unit . Any attempt to disassemble the unit or moving the knob
can prevent the unit working correctly.
1.
Open the Gun Body. (See 7-15 page 90)
2.
Remove the Light Receiving Unit from the indentations in the Gun Body and
disconnect the connector to remove the Light Receiving Unit.
Gun body (L)
Indentation
Indentation
Connector
Light receiving unit
(To reinstall, insert the unit into the indentations in the
gun body while placing its connector facing to the bottom.)
3.
Reassemble in reverse order.
•
After replacing the Light Receiving Unit, be sure to Initialize the Guns.
(see 6-2-3-2 page 58)
92
7-18 Replacing the Gun Solenoid
1.
Remove the Gun Body. (see 7-16 page 91)
2.
Disconnect the solenoid connector.
3.
Remove the button head screw (M3x8) and remove the Solenoid Bracket.
4.
Remove the cap screw (M3x5) and remove the Earth terminal and tooth washer (M3).
5.
Remove 2off pozi head screws (M4x6), with flat and spring washers, and remove the
Slide Bracket.
6.
Remove 4off cap screws (M3x5) and remove the Solenoid Unit.
7.
Remove the Rubber Spacer from the Solenoid Unit. Take care not to lose the spring
while removing the Rubber Spacer.
Button-head screw (M3 x 8)
Cap screw (M3 x 5)
Earth terminal
Solenoid unit
Tooth washer (M3)
Spring
Gun body
Pozi head screws (M4 x 6)
(with both flat and spring washers)
Cap screws (M3 x 5)
8.
Solenoid bracket
Slide bracket
Reassemble in reverse order. Pay attention to the installing order of the E-type Stop
Ring and Rubber Spacer and the direction of the Spring.
Rubber spacer
Solenoid unit
Slide guide
Solenoid
bracket
E-type stop ring
Spring
•
•
After replacing the solenoid Unit, go to Test Mode to check operation.
(see 6-2-3-4 page 62)
Be sure to initialize the Guns.
(see 6-2-3-2 page 58)
93
7-19 Replacing the Trigger Microswitch
1.
Open the Gun Body. (See 7-16 page 91)
2.
Disconnect the two Faston terminals and replace the Microswitch.
Microswitch
Connect the blue wire to
the N.O. terminal.
Faston terminals
Connect the black wire to the COM terminal.
3.
Reassemble in reverse order.
•
After replacing the Microswitch, go to Test Mode to check operation.
(see 6-2-3-3 page 61)
Be sure to initialize the Guns.
(see 6-2-3-2 page 58)
•
94
7-20 Replacing the Gun Harness
1.
Remove the Gun Assy (See 7-14 page 89)
2.
Remove the 2off button head screws (M4x10) and detach the Connector Cover B.
3.
Remove the Gun Slides (See 7-15 page 90) and the Gun Body. (See 7-16 page 91)
4.
Remove the cap screw (M3x5) and remove the Earth terminal and tooth washer (M3).
5.
Disconnect the connectors and remove the two Faston terminals from the microswitch.
6.
Remove the button head screw (M3x8) that attaches the Gun Harness to the Gun
Body (L), and replace the Gun Harness.
Microswitch
Connect the blue wire to
the N.O. terminal.
Faston terminals
Connect the black wire to the COM terminal.
7.
Reassemble in reverse order.
•
After replacing the Gun Harness, go to Test Mode to check operation.
(see 6-2-3-3 page 61)
Be sure to initialize the Guns.
(see 6-2-3-2 page 58)
•
95
7-21 Replacing the Pedal Micro Switch
1.
Remove the Pedal Assy from the Coin Tower Assy. ( See 7-2-1 page 71).
2.
Remove 4off security screw (M5x12) and remove the Cover M.
Torx screws (M5 x 12)
Torx screws (M5 x 12)
Cover (M)
3.
Remove 2off pozi head screw (M3x16) and remove the switch.
When replacing the switch, ensure that the wires are fitted to the correct terminals.
Pozi head screw (M3x16)
Microswitch
4.
Slacken the 2off whizztite nuts (M4) and adjust the microswitch bracket so that the
switch plunger operates the switch correctly without bending the switch lever against
the switch body.
Microswitch
pedal
released
Foot plate
Whizz nut
Pedal
pressed
5.
•
96
Plunger
Reassemble in reverse order.
After replacing the Micro Switch, go to Test Mode to check operation.
(see 6-2-3-3 page 61)
7-22 Replacing the Pedal Plunger
1.
Remove the Cover (M). (See 7-2-1(3) page 71).
2.
Remove the Holder. (See7-2-1-(4) page 72)
3.
Pull out the Plunger from the Holder, and replace the Plunger with a new one. When
installing a new plunger, apply light grease to the entire contacting surface between
the plunger’s holder and plate.
Holder
Spr ing (B)
Plunger
4.
Remove old grease from the plate surface on the pedal, and apply new grease.
Plate
Apply grease.
5.
Reassemble in reverse order.
•
After replacing the Plunger, go to Test Mode to check operation.
(see 6-2-3-3 page 61)
97
8. TROUBLESHOOTING
8-1
Monitor Cabinet Assy
Symptom
No image is displayed on the
monitor
There is no sound from the
speakers
The SIDELED PC not lighting
8-2
U su al C au se
Badly connected connector
Check all connectors
The Projector is defective
Replace the Projector
The Game PCB Assy is
defective
Replace the Game PCB Assy
The Volume level is too low
Adjust the volume setting
Badly connected connector
Check all connectors
The AMP PC Board is
defective
Replace the AMP PC Board
The Game PC Board Assy is
defective
Replace the Game PC Board
A ssy
Badly connected connector
Check all connectors
The SIDELED PC Board is
defective
Replace the SIDELED PC
Board
The NA-JV PC Board is
defective
Replace the NA-JV board
Header Assy
Symptom
U su al C au se
The fluorescent lamp does not Poor connection
light
The fluorescent lamp is burnt
out
8-3
Action
Check all connectors
Replace the fluorescent lamp
The starter is burnt out
Replace the starter
U su al C au se
Action
Pedal Assy
Symptom
The pedal does not operate
properly
98
Action
Poor connection
Check all connectors
The Micro Switch is defective Replace the Micro Switch
The plunger is worn out
Replace the plunger
The NA-JV PC board is
defective
Replace the NA-JV PC board
8-4
Control Assy
Symptom
The SIDELED PC board is
not lit. (Inside the Control
Panel, Inside the Gun Tower)
There is no sound from the
speakers
8-5
U su al C au se
Action
Badly connected connector
Check all connectors
The SIDELED PC Board is
defective
Replace the SIDELED PC
Board
The NA-JV PC Board is
defective
Replace the NA-JV board
The Volume level is too low
Adjust the volume setting
Badly connected connector
Check all connectors
The AMP PC Board is
defective
Replace the AMP PC Board
The Game PC Board Assy is
defective
Replace the Game PC Board
A ssy
Gun Assy
Symptom
The gun does not shoot
correctly
The trigger does not work
The gun does not recoil
U su al C au se
Action
The gun sight is out of
adjustment
Adjust the gun sight
The tip of the gun barrel is
dirty
Clean
The filter is dirty
Clean
The tip of the gun is
positioned too close to the
screen
Keep the gun away from the
screen (more than 60cm
between gun tip and screen)
The same machines are next
to each other
Connect the frequency
changeover harness correctly
A poor connection
Check all connectors
The LED board is defective
Replace the defective LED
board
The light receiving unit is
defective
Replace the light receiving
unit
The CPU board is defective
Replace the CPU board
The NA-JV PC board is
defective
Replace the NA-JV PC board
A poor connection
Check all connectors
The micro-switch is defective
Replace the micro-switch
The NA-JV PC board
Replace the NA-JV PC board
A poor connection
Check all connectors
The solenoid is defective
Replace the solenoid
The NA-JV PC board
Replace the NA-JV PC board
99
9. DISPOSAL
NOTICE
Directive 2002/96/EC
(Waste Electrical and Electronic Equipment - WEEE)
Information for users
This product complies with the EU Directive 2002/96/EC.
The crossed out wheelie bin symbol on the product means that at
the end of its useful lifespan, the product must be disposed of
seperately from ordinary household wastes.
Appropriate separate collection to permit recycling, treatment and
environmentally compatible disposal helps prevent negative
impact on the environment and human health.
For areas not in the EEC please ensure that disposal of this
product complies with all local legislation or requirements in
force.
100
101
10. PARTS
10-1 Monitor Cabinet (L)
Y
Z
Y
Z
A-A
A
102
A
Item
Description
1
Projector Monitor -46KH412S
7
Front Panel
8
Side Bracket
Part No
84000061
XTC4-NTC49201-1
XTC4-NTC1209-1
Projector Mask L
XTC4-NT4DX13MFG
Projector Mask R
XTC4-NT4DX13MFD
Projector Mask Top
XTC4-NT4DX13MFH
11 Projector Mask Bottom
XTC4-NT4DX13MFB
10
13 Front Decal L
40000847
14 Side Decal L
40000849
16 Bass speaker Grille
XTC4-NTC
17 Filter
30000101
19 'Fork Here' Decal
40000072
23 Adjustable Foot (M16x95)
88300079
24 Swivel Castor - 75mm
59000005
30 LED Board
31 Woofer - FAD205GA2713
XTC4-LEDPCB
XTC4-BASSSPEAKER
41 Header Joint
44 Header Joint 2
103
10-2 Monitor Cabinet (R)
Y
Z
Z
Y
A
A
Projector
A-A
104
Item
Description
6
Front Panel
7
Side Bracket
Part No
XTC4-NTC49201-1
XTC4-NTC1209-1
Projector Mask L
NT4DX13MFG
Projector Mask R
NT4DX13MFD
Projector Mask Top
NT4DX13MFH
10 Projector Mask Bottom
NT4DX13MFB
9
12 Front Decal R
40000848
13 Side Decal R
40000850
15 Bass Speaker Grille
XTC4-NTC2204-1
16 Filter
30000001
18 'Fork Here' Decal
40000072
22 Adjustable Foot (M16x95)
88300079
23 Swivel Castor - 75mm
59000005
28 LED Board
29
Woofer -FAD205GA2713
XTC4-LEDPCB
XTC4-BASSSPEAKER
105
10-3 Speaker Box Assy (L)
A
A
A-A
Item
Description
Part No
2
Top Bracket
XTC4-NTC1302-1
3
Header Cabinet Speaker Grille
XTC4-NTC1301-1
4
Header LED Acrylic
5
LED Bracket
XTC4-NTC3301-1
6
Header Bracket
XTC4-NTC1304-1
9
Countersunk Mounting Washer
10 SIDELED PC Board (Red)
11 Speaker
106
30000102
XTC4-NTC
XTC4-SIDELEDR
62000163
10-4 Speaker Box Assy (R)
A
A
A-A
Item
Description
Part No
2
Top Bracket
XTC4-NTC1302-1
3
Header Cabinet Speaker Grille
XTC4-NTC1301-1
4
Header LED Acrylic
5
LED Bracket
XTC4-NTC3301-1
6
Header Bracket
XTC4-NTC1304-1
8
Countersunk Mounting Washer
10 SIDELED PC Board (Blue)
10 Speaker
30000102
XTC4-NTC
XTC4-SIDELEDB
62000163
107
10-5 Header Assy
Item
Description
Part No
5
Top Header Acrylic
6
Countersunk Mounting Washer
7
Fluorescent Lamp 4ft
64500039
8
Starter
63000000
108
30000103
10-6 Control Assy
AMP PC board
Item
Description
Part No
1
500mA 1¼" A/S Fuse
63500637
2
Capacitor 22,000μF 25V
70200043
3
Bridge Rectifier
71000041
4
2A 1¼" Quick-Blo Fuse
63500604
5
1A 1¼" Quick-Blo Fuse
63500424
6
Transformer 18V @ 3A
67700015
7
Round Shape Vibration-Isolation Rubber - KB-20
XTC4-NT4DX11P15x12
109
10-7 Game PCB Assy
(
Detailed diagram of PCB tray)
Main PC board
Sub PC board
(Player 1 side)
(Player 2 side)
Security dongle
110
Item
Description
Part No
1
Case
XTC4-463-098
2
Cover
XTC4-463-092
3
HDD Mount Bracket
XTC4-463-093
4
Fan Bracket
XTC4-463-094
5
EX PCB Stay
XTC4-463-095
6
PCB Tray
XTC4-463-097
7
HDD Bracket
XTC4-463-096
8
Cushion (L)
XTC4-463-097
9
RISER PCB
XTC4-306-758
10 EXSOUND PCB
XTC4-306-759
11 UE PCB
XTC4-306-736
12 Fan Motor
XTC4-845-939
13 PCB Stay
XTC4-463-088
14 HDD
XTC4-306-760
15 USB Cover
XTC4-463-090
16 Video Cable
XTC4-007-350
17 LAN Cable (STP straight)
XTC4-007-301
18 USB-XA5P Cable
XTC4-007-348
19 USB-XA6P Cable
XTC4-007-349
111
10-8 Coin Tower Assy
(opposite side
Item
Description
)
Part No
2
Gun Console Lower Cross Member
XTC4-NTC1102-1
3
Gun Console Upper Cross Member Front
XTC4-NTC1103-2
4
Gun Console Upper Cross Member Rear
XTC4-NTC1104-1
10 Metal Instruction Panel
XTC4-NTC3101-1
11 Acrylic Instruction Panel
30000110
12 Coin Tower Side Decal L
40000852
13 Coin Tower Side Decal R
40000853
15 Adjustable Foot (M16x95)
88300079
16 Swivel Castor - 38mm
59000003
17 SecurDoor
53100351
18 Under Box
47000203
19 Cash Box
39000066
112
10-9
Pedal Assy
Item
Description
P e d a l A ssy
Part No
XTC4-PEDALASSY
7
Stopper Rubber
XTC4-631-217
8
Spring Cover
XTC4-717-324
9
Plunger
XTC4-631-219
10 Spring (A)
XTC4-717-325
11 Spring (B)
XTC4-717-326
1 2 P e d a l D e ca l
13 Micro Switch - KSL 13
40000762
XTC-000-027
113
10-10
Gun Tower Assy (L)
X
Z
Y
CPU board
NA-JV PC Board
Z
(opposite side
)
Y
X
A
A
A-A
114
Item
Description
Part No
2
Holster Panel
XTC4-NTC1116-1
4
Acrylic Panel A
30000104
5
Rear Acrylic L
30000105
6
Rear Acrylic R
30000106
7
Gun Tower Side Panel L
30000107
8
Gun Tower Side Panel R
30000108
9
LED Cover
XTC4-NTC3116-1
10 'Credit Available When Lit' Button
60200215
11 Panel Gun Hoop
45000210
15 Speaker Grille
XTC4-NTC1119-1
16 Gun Holder
XTC4-NTC1121-1
17 Countersunk Washer
18 Holster Decal L
19 SIDELED PC Board (Red)
XTC4-NTC
40000854
XTC4-SIDELEDR
20 Speaker
62000162
27 Reflection Preventing Decal
40000860
115
10-11
Gun tower Assy (R)
CPU board
Z
Y
X
Z
A
Y
(opposite
side
)
A
A-A
116
X
Item
Description
Part No
2
Holster Panel
XTC4-NTC1116-1
4
Acrylic Panel A
30000104
5
Acrylic Panel B
30000105
6
Gun Tower Panel R
30000106
7
Gun Tower Side Panel L
30000107
8
Gun Tower Side Panel R
30000108
9
LED Cover
XTC4-NTC3116-1
10 'Credit Available When Lit' Button
60200215
11 Panel Gun Hoop
45000210
15 Speaker Grille
XTC4-NTC1119-3
16 Gun Holder
XTC4-NTC1121-1
17 Countersunk Washer
18 Holster Decal R
19 SIDELED PC Board (Blue)
20 Speaker
27 Frequency Changeover Connector
28 Reflection Preventing Decal
XTC4-NTC
40000855
XTC4-SIDELEDB
62000162
XTC4-NTC
40000860
117
10-12
Joint Box Assy
Item
Description
Part No
1
Joint Box
XTC4-NTC1108-2
2
Joint Cover
XTC4-NTC1109-2
4
Relay PC Board
XTC4-RELAYPCB
118
10-13
Service Bracket Assy
Item
Description
Part No
Fuseholder 20mm Panel Mount
63500786
Fuse 20mm 2A Q/B
63500501
2
SPDT Toggle Switch - (momentary action)
60000010
3
Pushbutton Switch - 7mm Red F424
60000059
4
Miniature Slide Switch
60000023
5
Panel Meter - 3.4~6v
65000002
1
119
10-14
120
Gun Assy
Gun Assy (R) (Red Gun)
Item
Description
Part No
1
Gun Body (LR)
2
Gun Body (RR)
3
Slide (LR)
4
Slide (RR)
5
Finger Lever (LR)
XTC4-717-332
6
Solenoid Bracket
XTC4-717-303
7
Slide Bracket
XTC4-717-304
8
Tube Bracket (A)
XTC4-717-305
9
Tube Bracket (B)
XTC4-717-306
XTC4-717-330
XTC4-717-331
10 Rubber Spacer
XTC4-717-307
11 Rubber Stopper
XTC4-717-308
12 Trigger Spring
XTC4-717-309
13 Connector Cover (B)
XTC4-701-906
14 Gun Harness Assy
XTC4-717-340
15 Slide Rail
XTC4-107-150
16 Solenoid Unit
XTC4-717-316
17 Microswitch
XTC4-000-666
18 Pantai (Convex)
XTC4-007-143
19 Light Receiving Unit
XTC4-306-754
20 Gun Assy (Red)
XTC4-717-333
21 Strain Relief Rope
45000708
22 Gun Chain Clamp
45000211
Gun Assy (B) (Blue Gun)
Item
Description
1
Gun Body (LB)
2
Gun Body (RB)
3
Slide (LB)
4
Slide (RB)
5
Finger Lever (LB)
Part No
XTC4-717-350
XTC4-717-351
20 Gun Assy (Blue)
XTC4-717-352
XTC4-717-355
121
SCHEMATIC 1
5
4
+12v
+5v
C
B
A
GND
E
EARTH
SPOUT+V+ 21
SPOUT_V- 9
GND
EARTH
GND
XAD8P
1
N.C.
2 SENSE3 DATA4 DATA5 DATA+
6 DATA+
7
GND
8
GND
XAD32P
X_POS2
Y+POS2
AGND
+5V
SLED1_U
SLED2_V
SLED2_S
4
0
4
2
8
VH4P
0
0
1
2
3
4
2
1
2
3
4
GND
GND
+5V
+5V
XAD40P
OUTSCR2
TRIGGER2
SOL2
PEDAL2
+5V
GND
PSELECT2
GND
SERVICE2
TEST2
GND
DOWN2
ENTER2
+5V
CC2
COIN2
2
4
11
13
15
17
19
2
4
11
13
15
17
19
16
15
23
24
22
39
26
20
28
40
12
7
19
14
13
17
21
1
5
16
15
23
24
22
39
26
20
28
40
12
7
19
14
13
17
21
1
5
9
0
0
14
9
0
0
5
6
7
172157
M1PF
(AMP)
1 1
1
2
3
4
5
6
7
8
V329
NA-JV PCB
Assy
(2P)
6
1
2
3
1
2
3
SPOUT_V+
SPOUT_V-
GND
+12V
1
2
1
2
2
3
1
6
2
3
1
6
XMP9P
X_POS2
Y_POS2
GND
OTSCR2
172164
M1PM
(AMP)
SHIELD
+5V
A
B
C
D
GND
1
7
6
5
4
3
2
1
7
6
5
4
3
2
16
13
0
14
172160
M6PF
(AMP)
0
9
1
4
5
9
0
16
0
8
13
E
0
9
1
4
5
9
0
1
2
3
4
5
6
1 16
2 13
0
3
4 14
5 172168
M6PM
6
(AMP)
350777
U2PM
(AMP)
8
1
E
2
14
16
13
7
350778
U2PF
(AMP)
8
1
E
2
7
0
E
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
172166
M3PM
(AMP)
1
2
3
0
A
B
C
D
E
F
SHIELD
TRIGGER2
GND
+24V
SOL2
EARTH
1
2
3
4
5
6
1
2
3
4
5
6
+5V
A
B
C
D
GND
172158
M6PF
(AMP)
4
33
0
35
GUN
PCB
ASSY
172167
M4PM
(AMP)
0
4
7
1
2
3
1
2
3
JOINT BOX
172160
M6PF
(AMP)
GAME PCB
1
ethernet P1
350778
U2PF
(AMP)
ETHERNET
1
XH 3P
+12V
N.C.
SLED2_S
XMP 19P
19
4
18
28
17
28
16
9
15
0
14
33
13
4
12
1
11
0
10
9
0
8
34
7
8
6
35
5
4
3
2
1
12v 2.2w
V329 SIDELED PCB ASSY
1
1
2
3
4
5
6
0
9
1
4
5
172168
M6PM
(AMP)
E
172160
M6PF
(AMP)
USB-A P2
1
GAME PCB
SHELL
DATAGND
SENSE
DATA+
N.C.
1
2
3
4
5
6
172168
M6PM
(AMP)
1 0
2 9
3 1
4 4
5 5
172166
M3PM
(AMP)
350777
U2PM
(AMP)
6
172157 172165
M2PF M2PM
(AMP) (AMP)
1
2
4
33
0
35
172159
M4PF
(AMP)
DISPENSE SWITCH
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
MARS
CASHFLOW
PINOUT
DESIGNITION
CASHFLOW
4
1
33
2
1
3
35
4
172167 172159
M4PM M4PF
(AMP) (AMP)
4
9
0
4
0
15
11
0
172168 18
M6PM 10
(AMP) 19
1
2
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
4
33
1
35
CROSS PCB
ETHERNET
350865
U1PM
(AMP)
1 EARTH
1
2
3
4
5
6
4
0
+12V
GND
ethernet P2
SHELL
DATAGND
SENSE
DATA+
N.C.
1
2
3
4
172167 172159
M4PM M4PF
(AMP) (AMP)
4
1
1 4
33
2
2 33
8
3
3 8
34
4
4 34
PEDAL ASSY
0
10
19
0
18
15
11
1
2
3
4
SOLENOID
ASSY
SM2P
172158
M3PF
(AMP)
1
PEDAL2
GND
2
3
EARTH
172166
M3PM
(AMP)
XH 6P
GUN ASSY
XAD 12P
12v 2.2w
0
1
+12V
N.C.
SLED2_V
1
2
3
0
USB-A P1
1
2
4
1
2
3
+12v
+5v
C
B
A
GND
1
2
3
4
5
6
XH2P
0
4
172165
M2PM
(AMP)
1 +123
2 SLED1_0
+12V
GND
+12V
+5V
+24V
1
2
3
XMP 7P
1
1
2
3
4
5
6
7
8
9
FSELECT2
GND
N.C.
XH 3P
XM6P
E
1 1
350866 350865
U1PF U1PM
(AMP) (AMP)
9
1
2
3
4
5
6
7
8
9
CPU BD
(2P)
172165
M2PM
(AMP)
1
2
3
4
5
6
4
350782
U9PF
(AMP)
V329 SIDELED PCB ASSY
5
4
1
2
172157
M2PF
(AMP)
172161
M9PF
(AMP)
1
2
3
4
5
6
7
8
9
1
2
172168
M6PM
(AMP)
4
5
15
11
0
18
10
19
1
2
3
1
2
3
172158
M3PF
(AMP)
1
2
1
2
350778
U2PF
(AMP)
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
SERVICE
172160
M6PF
(AMP)
SERVICE
172160
M6PF
(AMP)
ENTER
TEST
SELECT UP
SELECT DOWN
0
0
2
VH4P
1
2
3
4
1
2
3
4
GND
GND
+5V
+5V
XAD 8P
4
9
5
1
1
+12V
2
+5V
3
C
4
B
5
A
6
GND
7
EARTH
8 SPOUT_V+
9 SPOUT_V172161
M9PF
(AMP)
4
5
4
0
4
2
8
XAD 32P
3
X_POS1
4
Y_POS1
AGND 11
+5V 13
SLED1_U 15
SLED1_V 17
SLED1_S 19
5
21
1
12
7
19
13
14
17
15
23
22
24
39
26
20
28
40
16
3
4
11
13
15
17
19
16
13
0
14
1
10
19
0
15
18
11
16
13
172160
M6PF
(AMP)
1
2
3
4
5
6
16
13
0
14
1
2
3
4
5
6
172168
M6PM
(AMP)
4
6
8
1 1
E
2 2
350777 350778
U2PM
U2PM
(AMP)
(AMP)
0
0
14
9
0
0
5
6
7
172165
M1PM
(AMP)
172164
M1PM
(AMP)
9
0
0
14
E
13
8
0
16
0
9
1
4
5
9
0
XMP 9P
2
3
1
6
2
3
1
6
X_POS1
Y_POS1
GND
OUTSCRT
CPU BD
(1P)
XMP 7P
SHIELD
+5V
A
B
C
D
GND
1
2
3
4
5
6
7
1
2
3
4
5
6
7
0
9
1
4
5
9
0
12
11
10
9
8
7
6
5
4
3
2
1
XAD 12P
12 EARTH
11 SOL1
10 +24V
GND
9
TRIGGER1
8
SHIELD
7
F
6
E
5
D
4
C
3
B
2
A
1
XH 2P
350866
UIPF
(AMP)
E
XH 3P
+12V
N.C.
SLED1_S
SERVICE
TEST
SELECT UP
SELECT DOWN
0
1 1
1
2
3
ENTER
SM 2P
SOLENOID
ASSY
4
9
1
8
5
0
1
2
1
2
1
2
3
4
5
6
1
2
3
4
5
6
GND1
+12V
7
0
1
2
E
3
172166
M3PM
(AMP)
XMP 6P
+12V
+5V
C
B
A
GND
FSELECT1
GND
N.C.
1
2
3
1
2
3
1
2
3
4
5
6
GUN ASSY
0
4
9
1
8
5
0
E
21
9
1
2
3
7
0
1 1
1
+12V
2 GND(+24V)
3
+12V
4
+5V
5
+24V
6
7
GND
8
EARTH
9
GND
350872
U9PF
(AMP)
1 N.C.
2 SENSE
3 DATA4 DATA5 DATA+
6 DATA+
7 GND
8 GND
V329
NA-JV PCB
Assy
(1P)
172165
M2PM
(AMP)
+12V
1
2 SLED1_0
1
2
3
4
5
6
7
8
XAD 40P
5
COIN1
21
+5V
1
CC1
12
SERVICE1
7
TEST1
19
GND
13
UP1
14
DOWN1
17
ENTER1
TRIGGER1 15
23
SOL1
22
+5V
24
PEDAL1
39
GND
PSELECT1 26
20
GND
CSELECT1 28
40
GND
16
OUTSCR1
XH 3P
PEDAL1
GND
EARTH
172158
M3PF
(AMP)
1
2
3
4
5
6
XH 6P
+5V
A
B
C
D
GND
2A Q/B
GUN
PCB
ASSY
METER
PEDAL ASSY
DISPENSE SWITCH
1
2
3
4
7
350865
UIPM
(AMP)
172166
M3PM
(AMP)
SPOUT_V+
SPOUT_V-
WIRE COLOUR CODE
0 BLACK
1 BROWN
2 RED
3 ORANGE
4 YELLOW
5 GREEN
6 BLUE
7 VIOLET
8 GREY
9 WHITE
E GREEN/YELLOW (EARTH)
172158
M3PF
(AMP)
1
2
3
1
2
3
1
2
3
4
33
0
35
XH 3P
+12V
N.C.
SLED1_V
1
2
3
4
172159
M4PF
(AMP)
V329 SIDELED PCB ASSY
12v 2.2w
1
2
3
4
4
33
0
35
172167
M4PM
(AMP)
SCHEMATIC 2
+12V
GND
+12V
+5V
+24V
GND
EARTH
GND
4
1 +12V
2 SLED1_U 5
1
2
3
4
5
6
7
8
9
0
4
2
8
0
E
0
4
PS2
GAME PCB
Assy (L)
172166
M6PM
(AMP)
H.D. ‘D’ CONNECTOR 15w
1
VRED
2
VGREEN
3
VBLUE
4
5
6
VGND
7
8
9
10
VGND
11
12
13
VSYNC
14
15
PS2
GAME PCB
Assy (L)
1
2
3
4
5
6
1
2
3
4
5
6
2
4
2
0
0
0
(9)
U6PM
(AMP)
EXSOUND
PCB
20
25
4
26
22
5
1
2
3
4
5
6
4
V329 SIDELED
PCB Assy
172167 172159
M4PM M4PF
(AMP) (AMP)
1
1
2
2
3
3
4
4
VL8P
RCA
RCA
SOUND L OUT
RCA
SOUND L IN
RCA
SOUND R OUT
RCA
SOUND R IN
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
4
0
2
4
0
1
2
3
4
1
2
3
4
1
2
3
4
5
6
7
8
SPOUT_L+
SPOUT_LSPOUT_R+
SPOUT_RSPOUT_V+
SPOUT_VSPOUT_W+
SPOUT_W-
2
0
XH3P
+12v
1
N.C.
2
SLED1_0
3
1
2
3
5
V329AMP PCBAssy (R)
RCA
JST VH-6P
+5V
1
+5V
2
GND
3
GND
4
+12V
5
GND
6
H.D. ‘D’ CONNECTOR 15w
1
VRED
2
VGREEN
3
VBLUE
4
5
6
VGND
7
8
9
10
VGND
11
12
13
VSYNC
14
15
2
4
2
0
0
0
U6PF
(AMP)
PROJECTOR CABINET
(L - Player 1)
USB-A
172160
M6PF
(AMP)
1
2
3
4
5
6
20
25
26
22
0
4
0
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
HEADER Assy
FLUORESCENT Assy
ETHERNET P2 USB-A P2
ETHERNET
20
26
25
22
21
9
27
23
1
2
3
4
5
6
7
8
172165
M2PM
(AMP)
172157
M2PF
(AMP)
1
1
2
2
SP1 (L)
20
26
CABINET
SPEAKERS
(L)
GND
+12v
GND
+5v
25
1
2
22
2
5
6
1
2
172165 172157
M2PM M2PF
(AMP) (AMP)
SP2 (R)
0
27
9
1
2
1
2
23
172157 172165
M2PF M2PM
(AMP) (AMP)
4ohm 24W
20
172166
M3Pm
(AMP)
21
1
2
3 9
SHIELD
F
E
D
C
B
A
1
2
3
172158
M3PF
(AMP)
SPOUT_V-
350715
U6PM
(AMP)
9
2
4
2
0
0
0
1
2
3
4
5
6
FAN
1
2
3
4
5
6
350781
U6PF
(AMP)
2
5
6
0
15
11
7
17
2
4
2
0
0
0
6
SPOUT_V+
20
SYNC
XH7P
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LED PCB
GND
GND
A
B
C
+5v
+12v
XH6P
GND
A
B
C
+5v
+12v
LED PCB
1
2
3
THOMSON
46” PROJECTOR
46KH412S 15Khz
5
1
2
3
4
9
21
9
15
11
7
17
1
2
3
1
1
2
SCART PLUG
RED
GREEN
BLUE
GND
1
2
3
RCA
SOUND R OUT
LED PCB
(8)
2Way EURO MAINS CONNECTOR
1
230vAC LIVE
2
230vAC NEUT
1
E
6
172166
M3PM
(AMP)
LED PCB
LED PCB
(7)
(6)
+12V
GND
SPOUT_V+
(5)
1
2
1
LED PCB
0
4
2
8
USB-A
END
LED PCB
+12V
GND
+12V
+5V
+24V
0
E
0
2
SHIELD
F
E
D
C
B
A
CPU BD
1
1
2
3
4
5
6
7
GND
GND
A
B
C
+5v
+12v
2
LED PCB
1
2
3
4
5
6
7
SPOUT_V-
XH6P
XH7P
3
23
LED PCB
GND
A
B
C
+5v
+12v
SOUND L OUT
0
27
3
1
2
AMP UNIV 3w
2
VH4P
1
2
3
4
EXSOUND
PCB
RCA
2
5
6
172158
M3PF
(AMP)
4ohm 24W
1
2
3
4
5
6
SPOUT_L+
SPOUT_LRCA
SPOUT_R+
SPOUT_R- SOUND L IN
SPOUT_V+
RCA
SPOUT_VSOUND R IN
SPOUT_W+
SPOUT_W-
1
2
3
4
5
6
7
8
22
1
2
RCA
RCA
GND
+12v
GND
+5v
172165 172157
M2PM M2PF
(AMP) (AMP)
172165 172157
M2PM M2PF
(AMP) (AMP)
1
2
3
4
5
6
1
2
3
4
5
6
7
8
0
20
26
25
22
21
9
27
23
VL8P
25
1
2
1
2
172157
M2PF
(AMP)
JSTVH-6P
1
+5V
2
+5V
3
GND
4
GND
5
+12V
6
GND
V329AMP PCBAssy (L)
1
2
1
2
CABINET
SPEAKERS
(R)
F
E
D
C
B
A
1
2
3
4
172157 172165
M2PF M2PM
(AMP) (AMP)
26
SP2 (R)
1
2
3
4
350720
U9PM
(AMP)
1
2
3
4
5
6
20
20
25
26
22
1
2
3
4
5
6
350777
U2PM
(AMP)
USB-A P1
4
0
SP1 (L)
1
2
3
4
5
6
172159
M4PF
(AMP)
172167
M4PM
(AMP)
ETHERNET P1
350720
U9PM
(AMP)
V329 SIDELED PCB Assy
ETHERNET
20
25
4
26
22
5
172168
M6PM
(AMP)
172160
M6PF
(AMP)
+12v
N.C.
SLED1_0
1
2
3
1
2
3
GND
EARTH
GND
5
1
2
3
4
5
6
7
8
9
4
XH3P
4
1 +12V
2 SLED1_U 5
172157
M2PF
(AMP)
LED PCB
LED PCB
LED PCB
(4)
(3)
(2)
(1)
LED PCB
6
E
1
LED PCB
172166
M3PM
(AMP)
4
1
+12V
9
2
+5V
1
3
C
8
4
B
5
5
A
0
6
GND
E
7 EARTH
8 SPOUT_V+ 21
9 SPOUT_V- 9
6
0V
EARTH
230vAC
1 1
2 2
3 3
172169
M9PM
(AMP)
350767
U3PF
(AMP)
6
E
1
2
5
6
0
350766
U3PM
9
LED PCB
LED PCB
(9)
1
F
E
D
C
B
A
1
2
3
4
5
6
CPU BD
END
LED PCB
(10)
1
2
3
4
5
6
(8)
LED PCB
(7)
(6)
LED PCB
(5)
2Way EURO MAINS CONNECTOR
1
2
1
2
15
11
7
17
15
11
7
17
20
20
230vAC LIVE
230vAC NEUT
THOMSON
46” PROJECTOR
46KH412S 15Khz
SCART PLUG
RED
GREEN
BLUE
GND
SYNC
LED PCB
(10)
BLUE
5AMP Q/B
BLUE
E
6
EARTH
230vAC
350783
U12PF
(AMP)
350778
U2PF
(AMP)
+
~
22,000μF 35v
GREEN/YELLOW
SWITCHMODE POWER SUPPLY
PROJECTOR CABINET (R - Player 2)
EARTH
STARPOINT
1
2
3
4
~
0
1
2
1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
926647
U15PF
(AMP)
2A SLO-BLO
-
350780
U4PF
(AMP)
FAN
1
2
3
0V
(1)
4
0
0
0
0
0
0
0
0
0
0
0
0V
LED PCB
1A Q/B
1
2
3
4
230vAC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
BROWN
1
GREEN/YELLOW
230vAC 50hZ
MAINS IN
1
2
3
4
5
6
7
8
9
10
11
12
5AMP Q/B
FILTER
Assy
350735
U12PM
(AMP)
INTERLOCK
SWITCH
230V
350779
U4PF
(AMP)
172166
M3PM
(AMP)
6
E
1
GRN/YEL
1
1
2
3
4
5
6
7
8
9
10
11
12
SCHAFFNER MAINS-IN FILTER Assy
BROWN
1
2
2
2
2
2
2
4
4
4
4
4
4
E
18V
8
0
8
0
350866 350865
U1PM
U1PF
(AMP) (AMP)
500mASLO-BLO
500mASLO-BLO
LED PCB
(2)
LED PCB
(3)
LED PCB
(4)
4
1
+12V
9
2
+5V
1
3
C
8
4
B
5
5
A
0
6
GND
E
7
EARTH
21 SPOUT_V+ 8
9 SPOUT_V- 9
172169
M9PM
(AMP)
Copies of Namco Game Manuals can be downloaded from our website:
www.namco.co.uk
listed under Components Distribution
For all Parts or Technical Support contact:
Brent Electronic,
Namco House,
Units 7-8, Acton Park Estate,
The Vale,
London. W3 7QE
www.brentelectronic.co.uk
For Technical Support, Warranty and
Advance Replacement Parts:-
+44 (0) 20 8324 6120
For Consumable Parts:-
+44 (0) 20 8324 6102
Fax for both:-
+44 (0) 20 8324 6126

advertisement

Key Features

  • Installation guide
  • Operation guide
  • Relocation and transportation guide
  • Maintenance guide
  • Disposal guide
  • Player and bystander safety guidelines
  • Machine feature usage instructions
  • Correct operation procedures
  • Information for inquiries and repairs

Frequently Answers and Questions

How do I install the Time Crisis 4 DX arcade game machine?
The manual includes detailed instructions on installing the machine correctly and safely. Refer to the "Installation" section for specific steps and guidelines.
What are the safety precautions I should take while operating the Time Crisis 4 DX?
The manual emphasizes the importance of maintaining customer safety at all times. It outlines specific safety guidelines to ensure both players and bystanders are protected. Refer to the "Safety Considerations" section for detailed information.
How do I clean and maintain the Time Crisis 4 DX machine?
The manual includes a thorough maintenance section that covers cleaning procedures, regular maintenance tasks, and instructions for replacing specific components. Refer to the "Maintenance" section for detailed information.
How can I access troubleshooting information for the Time Crisis 4 DX machine?
The manual provides a troubleshooting section addressing common issues with specific components of the machine. Refer to the "Troubleshooting" section for assistance.

Related manuals

Download PDF

advertisement