Mattel RoseArt Graphic Skinz Design Studio User manual

Mattel RoseArt Graphic Skinz Design Studio User manual
45915/6+
INCLUDES:
6 Piece Motorized Vacuum Chamber Machine, Vacuum Bag Assembly, Sponge,
11 Piece Butterfly, 12 Piece Flower Box, 10 Piece Seahorse, 10 Graphic Skinz™ Transfers
4 in x 4 in (10.2 cm x 10.2 cm) each, 20 Graphic Skinz™ Transfers 2 in x 4 in
(5.08 cm x 10.2 cm) each, Sponge Detailer, Instruction Sheet
ITEMS NEEDED BUT NOT INCLUDED:
4 - AA BATTERIES, BOWL, WATER, SCISSORS
ADULT ASSEMBLY REQUIRED. ADULT SUPERVISION RECOMMENDED.
ASSEMBLE THE VACUUM CHAMBER MACHINE
INSTALLING AND CHANGING BATTERIES:
1. Use Phillips head screwdriver to loosen the screw of the battery cover on the bottom of BASE.
чо | [Е Го | [Е
2. Remove battery cover. If replacing batteries, remove used batteries and dispose of properly. 9 D ® D
3. Insert 4 AA BATTERIES and match direction of diagram inside battery case. = E Е a
4. Replace battery cover and tighten screw. : > : >
5. Make sure there is no water in the RESERVOIR before installing or replacing batteries. > а > о
6. For more detailed information see back раде. = 19 ®
2 VACUUM CHAMBER ASSEMBLY BAG ASSEMBLY
C---Bag
— Hama
Lid Slots----{ ¿ e
---Upper Housing y bag a
65) --Hose
Ч
Strut A Strut B 1. ,
INSTALLING AND REPLACING VACUUM BAG:
1. Insert BAG down through the hole in the UPPER HOUSING and be
sure BAG VALVE is facing the rear of the machine, Firmly press BAG RING
Water---= down into place.
Reservoir
2. Attach bottom of BAG to the BASE by hooking the holes on BAG to
BAG HOOKS on the top of the BASE.
BACK ---
EE NOTE: The BAG needs to be hooked onto BASE for proper operation and
Base------ best results. (FIGURE A).
3. Connect the HOSE of BASE to the BAG VALVE on the rear of the BAG.
FRONT Be sure the HOSE is pressed all the way onto the BAG VALVE stem.
NOTE: Top edge of BAG RING needs to be fully inserted into hole so it's
ASSEMBLE THE VACUUM CHAMBER MACHINE: flush with the top edge of the UPPER HOUSING. (FIGURE B).
1. Insert the 2 SUPPORT STRUTS into the slots on the top CORRECT BAG ASSEMELY. NO GAP IS VISIBLE. INCORRECT!
of the BASE and press firmly into place. FIGURE B
2. Attach the UPPER HOUSING to the top of the SUPPORT =
STRUTS and press firmly into place. Bag. - -
-
3. Attach the LID by inserting the hinge pins of the LID into "9
the slots on the UPPER HOUSING. -
4. Insert WATER RESERVOIR into slot at rear of BASE. Upper
Housing
READY TO SKIN:
A
—
Choose a Skinz and cut off the
white border. Have an adult
help you with this.
NOTE: Larger pieces may
require the 4” X 4" Skinz or
patchworking smaller Skinz
pieces in order to fully cover
the piece.
Open the lid of the vacuum
chamber and place the sponge
and model into the vacuum
bag. Make sure the water
reservoir is inserted into the
back of the machine.
DESIGN TIPS:
Select a model part to decorate.
Remove the clear protective
plastic cover from the Skinz then
gently place the model on the
Skinz and cut around the model
Fill a bowl with cold tap water
and thoroughly soak the sponge.
Wring out excess water so that
the sponge is not dripping wet.
part leaving enough border to
wrap around edge.
NOTE: Set aside remaining Skinz
to use on other model parts.
stick the clear protective cover
back onto the unused portions
of the Skinz.
Keep water away from the
unused Skinz or they could get
damaged.
Close the lid and hold the
vacuum chamber suction
Wait approximately 10 seconds
then open the lid. Remove the
Before you begin, lay out model parts and Skinz. Separate the 2 part, perforated Skinz.
Do not remove the protective plastic cover from the Skinz until ready to use.
£
Wrap the fully soaked sponge
around model part completely
covering the Skinz and the model.
button with your finger for
approximately 20 seconds or
until the bag is suctioned
tightly around the sponge
and all the water has been
extracted from the bag or
sponge. Remove finger from
button.
sponge and unwrap the model
part and remove the paper
backing from the Skinz.
again and again.
1. To create an overlapping patchwork design, keep the protective plastic cover on the Skinz and cut to
desired shape (circle, heart, etc.) Remove the plastic protective cover from the cut Skinz piece and place on
your model part in desired area you want to cover. SEE DIAGRAM 1
DO NOT OVERLAP ALL PIECES AT ONCE. APPLY SKINZ PIECES ONE AT A TIME.
2. Graphic Skinz™ can be layered so that you can re-skin your customizable models with a new design
3. Customize your own stuff! Cell phone cases, action figures, and just about any non-electronic item you
can fit inside the Vacuum Chamber Machine.
Use the Sponge Detailer to
smooth edges and remove any
air bubbles. Fold or wrap any
excess Skinz material around
the edges of the piece.
Once all pieces are decorated to
your liking, assemble a
customized model by gently
snapping the parts together.
Repeat previous steps to apply
more Skinz.
DIAGRAM 1
IMPORTANT:
1. Do not place Skinz sticky side down on table or work surface as it may damage the Skinz and stick to surface
2. Allow the Skinz to dry for approximately 20 seconds as they will remain tacky until completely dry.
3. Check the water reservoir in between skinning parts to ensure that it is not full and in need of emptying.
DO NOT EMPTY WHILE MOTOR IS RUNNING. DISPOSE OF WATER FROM RESERVOIR DOWN THE SINK.
DO NOT REUSE.
4. Machine is equipped with an auto-shut off and will shut down if the motor becomes too hot. The motor will
reset itself after it cools down.
5. If the machine can no longer empty the bag of air, it may be a sign that you need to replace the batteries.
MODEL ASSEMBLY:
1. The models come unassembled for easy decorating.
EMPTYING RESERVOIR
2. Once Skinz have been applied to the model parts they can be assembled by snapping them together.
3. Assemble models as shown below for each model. Numbers show order of assembly.
BUTTERFLY UNASSEMBLED BUTTERFLY ASSEMBLED
11
10 |
a
1.
‘ 7
3 |
À
THN 8 « \
4 x э
Ч - | \
MA
>
1"
— 9
e м
SEAHORSE UNASSEMBLED SEAHORSE ASSEMBLED
SET 1 - Seahorse 7 \ 16
4 2 m
1 To
- 7 5
8 Fd 9
SET 2 - Base
Assemble SET 1 then assemble SET 2.
Snap Seahorse onto Base.
FLOWER BOX UNASSEMBLED
12
FLOWER BOX ASSEMBLED
10
IMPORTANT TIPS FOR USE, CLEANING AND STORAGE OF THE GRAPHIC SKINZ DESIGN STUDIO:
* Graphic Skinz™ are not intended for use on skin. * When skinning your own items be sure to select items that are non-electronic * Do not
apply Graphic Skinz™ to a cell phone case/cover with the phone still in the case. This may cause damage to your phone. * Remove all water
after play. * Do not store vacuum chamber machine, sponges, water reservoir or vacuum chamber bags while they are still wet or damp.
* Keep lid open to allow bag to dry out when done skinning your stuff. = Adult assistance may be required.
NOTE: Do not place any sharp or pointed objects into sponge or plastic bag.
Consult with an adult before adding anything to the machine that is valuable or may be damaged by water.
Battery Information
BATTERIES REQUIRED
4x (NOT INCLUDED)
Alkaline batteries recommended.
Phillips screwdriver required.
This toy uses 4 replaceable AA/LR6 alkaline batteries.
CAUTION: Batteries are to be replaced and recharged by an
adult. Do not leave batteries within reach of children. Dispose
of properly according to your local recycling program. Do not
pundure, disassemble, mutilate, or incinerate batteries —
tteries may explode or leak.
To avoid battery leakage: (1) Non-rechargeable batteries must
never be echarged (2) Rechargeable batteries must be
removed from the product before recharging (3) Do not mix
battery types or old and new batteries. (4) Only batteries of
the size and type indicated should be used. (5) Batteries must
be inserted according to the correct polarity (+ / -). (6)
Remove batteries from toy if storing for a long period of time
or if batteries are exhausted. (7) Do not short circuit the
supply terminal.
|
y
© 1.5VAA/LR6 @ |]
ZN WARNING:
CHOKING HAZARD - Small parts.
Not for children under 3 years.
le OMT VY ASL ©
le 941/VWAS'| O
|
|
We 1.5VAA/LR6 @
‚Е.
SEE ALL THE POSSIBILITIES AT GRAPHICSKINZ.COM
1
© 2014 MEGA Brands International.
® and ™ denote trademarks of MEGA Brands
International and MEGA Brands Inc.
All rights reserved. Products and colors may vary.
Please retain this information for future reference.
Conforms to ASTM D4236.
Conforms to ASTM F963-11.
MEGA Brands Inc.
MADE IN CHINA. Eh Montreal (QC) HAT 1K4
INSTR-45915-AA-01 Canada
We create quality products at a great value!
If you are not satisfied with your purchase,
please contact:
( MEGA Brands America, Inc., Irvine, CA 92618 USA
1-800-CRAYONS www.megabrands.com
E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement