null  null
1/3" CCD BLACK & WHITE
CAMERA
INSTRUCTION MANUAL
Worldwide Support Center
1301 Waters Ridge Drive • Lewisville, TX 75057
(800) 796-2288 • (972) 353-6400 • FAX (972) 353-6670
Please read this manual thoroughly before use, and keep it handy for future reference.
1998 BY ULTRAK
ALL RIGHTS RESERVED
PRINTED IN KOREA
ULTRAK
1301 WATERS RIDGE DRIVE
LEWISVILLE, TEXAS 75057
(972) 353-6400
The information contained herein is subject to change without notice. Revisions or new editions to
the publicationmaybeissuedtoincorporatesuchchanges. Users of the product are responsible for
checking and complying with all federal, state and local laws and statutes concerning the monitoring
and recording of video and audio signals.
ULTRAK MAKES NO EXPRESS OR IMPLIED WARRANTIES OF ANY NATURE AS TO THE
PRODUCTS INCLUDED HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES OF
MERCHANTABLILTY AND FITNESS FOR A PARTICULAR PURPOSE.
All rights reserved. No part of this publication may be reproduced by any means without written
permission from Ultrak.
-2-
WARNING:
TO REDUCE THE RISKOFFIREOR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION
GRILLS.
CAUTION:
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the
product'senclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
-3-
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS -- All the safety and operating
instructions should be readbeforetheapplianceis operated.
2. RETAIN INSTRUCTIONS -- The safety and operating
instructions should be retainedforfuturereference.
3. CLEANING -- Unplug video equipment from the power
source beforecleaning. Do not use liquidcleaners or aerosol
cleaners. Use a damp cloth for cleaning.
4. ATTACHMENTS -- Do not use attachments not
recommended by the video equipment manufacturer as they
may result in the risk of fire, electric shock or injury to
persons.
5. WATER AND MOISTURE -- Do not use video equipment
near water -- for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, orthelike.
6. ACCESSORIES -- Do not place video equipment on an
unstable cart, stand or table. The video equipment may fall,
causing serious injury to a childoradult, and serious damage
to the equipment. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturer.
11. LIGHTNING -- For added protection for video equipment
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system. This will
prevent damage to the video product due to lightning and
power-line surges.
12. OVERLOADING --Do not overload wall outlets and
extension cords as this can result in a risk of fire or electric
shock.
13. OBJECT AND LIQUID ENTRY -- Never push objects of any
kind into video equipment through openings as they may
touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind
on theproduct.
14. SERVICING -- Do not attempt to service video equipment
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified servicepersonnel.
15. DAMAGE REQUIRING SERVICE -- Unplug video
equipmentfromthewalloutletandreferservicing to qualified
servicepersonnelunderthefollowingconditions:
A. When the power-supply cord or the plug has been
damaged.
B. If liquid has spilled, or objects have fallen into the video
product.
C.Ifthevideoproducthasbeenexposed to rain or water.
D. If the video product does not operate normally by
following the operating instructions, adjust only those
controls that are covered by the operating instructions as an
improper adjustment of other controls may result in damage
and willoften requireextensive work byaqualifiedtechnician
to restore the videoproduct to its normaloperation.
E. If the video product has been dropped, or the cabinet
damaged.
F. When the video product exhibits a distinct change in
performance --thisindicatesaneedforservice.
6A. Video equipment and cart
combinations should bemovedwith
care. Quick stops,excessive force,
andunevensurfaces may causethe
equipment and cart combination tooverturn.
7. VENTILATION -- Slots and openings in the cabinet and the
back or bottom are provided for ventilation, and to ensure
reliable operation of the video equipment and to protect it
from overheating. These openings must not be blocked or
covered. The openings should never be blocked by placing
the video equipment on a bed, sofa, rug, or other similar
surface. Video equipment should never be placed near or
over a radiator or heat register. Video equipment should not
be placed in a built-in installation such as a bookcase unless
proper ventilation is provided.
8. POWER SOURCES -- Video equipment should be operated
only from the type of power source indicated on the marking
label. If you are not sure of the type of power supplied to your
home, consult your video equipment dealer or local power
company. For video equipment designed to operate from
batterypowerrefer to the operating instructions.
9. POWER CORDS -- Do not allow anything to rest on the
power cord. Do not locate video equipment where the cord
willbeabusedbypersonswalkingonit.
10. HEED WARNINGS -- Follow all instructions marked on the
video equipment.
16. REPLACEMENT PARTS -- When replacement parts are
required, be sure the service technician has used
replacement parts specified by themanufacturer or that have
the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
17. SAFETY CHECK -- Upon completion of any service or
repairs to this video product, ask the service technician to
perform safety checks to determine that the video product is
inproperoperatingcondition.
18. FIELD INSTALLATION --Thisinstallation shouldbemadeby
a qualified service person and should conform to all local
codes.
-4-
TABLE OF CONTENTS
PURPOSE
7
INSTALLATION PRECAUTIONS
7
SYSTEM INSTALLATION
8
MAJOR OPERATING CONTROLS AND THEIR FUNCTION
10
MAJOR OPERATING CONTROLS AND THEIR FUNCTION
11
LENS ADJUSTMENT
13
TROUBLESHOOTING
18
MAINTENANCE
18
SPECIFICATION
19
-5-
THIS PAGE INTENTIONALLY LEFT BLANK
-6-
PURPOSE
The CCD Black & White Camera provides a low cost solution to closed circuit
television and security surveillance applications.
The camera features :
• 1/3" interline transfer CCD image sensor
• Supports standard CS or C-mount lens
• Equipped with electronic iris
• Compatibility with Video-type or DC-type auto iris lens
• Operates on AC 24V or AC 230V with line lock
• Excellent picture quality
• Two-year warranty
This manual describes how to setup and operate the camera.
INSTALLATION PRECAUTIONS
A. The mounting bracket must be mounted to a structured member such as a wall
or ceiling rafter using suitable fastener by install guide.
B. Select a suitable location for the camera. Install the camera stand or mounting
bracket in the selected location using a suitable fastener.
The camera stand or mounting bracket must be attached to a structural object,
such as a wall stud or ceiling rafter, that supports the weight of the camera and
mount.
C. If use AC 24V power adapter, only use the UL Listed Class 2 Power
Transformer.
-7-
SYSTEM INSTALLATION
Installation of the camera must be performed by qualified service personnel in
accordance with all local and national electrical and mechanical codes.
Perform the following steps to install the camera.
A. Remove all components from the package and identify the items that will be
used during installation:
• The camera
• Instruction manual
• Mini din connector (for Video-type or DC-type auto iris lens)
B. Other items used during the installation that are NOT supplied with the
camera may include:
•
•
•
•
•
•
Camera lens
Video cable
Camera stand or mounting bracket
AC 24V power supply
Mounting hardware
Monitor
-8-
G. Route the video cable from the monitor to the camera.
H. Plug the cable into the BNC output connector labeled " VIDEO OUT" on the
rear of the camera.
I. Plug the other end of the cable into the video input port on the rear of the monitor.
< KC4400MP >
J. Connect a two conductor power cable to the AC 24V input on the rear of the
camera.
24VAC CLASS 2
* If use AC 24V power
adapter,only use the
UL Listed Class 2 Power
adaptor.
~
G
~
.
FIGURE 1.
K. Apply AC 24V power to the camera.
L. Adjust the lens focus and iris controls for an optimum piture.
< KC4401MP, KC4402MP >
J. Apply AC 230V power to the camera.
K. Adjust the lens focus and iris controls for an optimum piture.
NOTE: Do not aim or point the camera towards the sun or into a strong light
-9-
< TOP VIEW >
6. Video Out BNC Connector
3. Auto Iris Connector
4. Stand Mount Bracket(up)
A/I
A
E/I
1. C/CS Back Focus
Adjust Ring
B
C
D
2. Back Focus Lock Screw
3. Auto Iris
Connector
5. Function
Switch
2. Back Focus
Lock Screw
6. Video Out BNC Connector
1. Back Focus
AdjustRing
KC4400MP
7. Stand Mount Bracket(down)
1. C/CS Back Focus
Adjust Ring
6. Video Out BNC
Connector
9. Power LED
6. Video Out BNC
Connector
9. Power LED
VIDEO OUT
VIDEOOUT
AC 230V IN
PWR
8. Power Cord
6. Video Out BNC
Connector
24VAC CLASS 2 PWR
8. Power Input
Terminal
FIGURE 1.
- 10 -
~ G
~
MAJOR OPERATING CONTROLS AND THEIR FUNCTION
1. Focus Adjust Ring
This ring is used to adjust the back focal length or picture focus by rotating this
ring to clockwise for CS-mount lens or counterclockwise for C-mount.
2. Back Focus Lock Screw
This screw is used to lock the focus adjust ring.
3. Auto Iris Connector
This 4-pin female connector supplies the power and either video signal or DC
control signal to the auto iris lens.
A 4-pin male connector, which can be mated with the camera's female connec
-tor, is supplied as a standard accessory.
This male connector can be installed on lenses which have incompatible type
connector.
See page 13, 14, 15 for installation details.
4, 7. Stand Mount Bracket
This threaded hole(1/4"-20) is used to mount the camera onto a mounting
bracket or tripod.
5. Function
A. A/I(Auto - Iris) / (DC / Video)
This switch is used to select the supplied auto iris control signal to the lens
from the Auto Iris Lens connector(3).
DC: Choose this position when the auto iris control lens requiring DC control
signal.
Video: Choose this position when the auto iris control lens requiring video
signal is mounted on the camera.
- 11 -
B. E/I (Electronic IRIS) / (ON / OFF)
Automatically varies the camera's shutter to mimic auto iris control, allowing
fixed or manual iris lenses to be used in a wider range of area.
When this function is used, turn off the F/F switch.
C. PHASE
Phase adjustment is used in multi-camera systems when power is supplied
from different sources, causing the camera to be out of phase.
This situation affects auto-switching of the cameras by causing a vertical flip
or roll during the switch interval.
The vertical phase adjustment allows the camera's line lock sync to be adjusted
minimum 270 degrees with reference to the zero line crossing of the ac
frequency.
• Ensure that all cameras are powered from the same electrical source and
wired in a similar fashion.
• Adjust the phase control on the top of the camera until there is no vertical
flip or roll on the monitor when using the auto-switcher.
D. IRIS
This control adjusts the control level of the auto iris control when the lens
selection switch(D) is set to the DC position and the auto iris lens which
requires the DC control voltage is mounted on the camera.
6. Video Out Connector
A 1.0 Vp-p / 75 ohms composite video signal is provided at this connector.
8. AC 24V Power Input Terminal / Power Cord
KC4400MP: This terminal accept, AC 24V power source.
Caution: Connect this to a AC 24V Class 2 Power Supply only.
KC4401MP, KC4402MP: Apply power AC 230V to the camera.
9. Power LED
While the power supply to the camera the LED lights green.
- 12 -
LENS ADJUSTMENT
1. MANUAL IRIS LENS
When using the manual iris lens, turn the iris ring on the lens to the OPEN
position and adjust the manual iris for the appropriate range.
Adjust during the brightest conditions, oening the lens without saturating the
picture. Set the EI switch to ON. Adjust the lens opening for the minimum
F-number yielding a good picture under the brightest scene conditions.
The manual iris is used in indoor applications where lighting from windows can
considerably affect the light level of the room.
2. VIDEO-TYPE AUTO IRIS LENS
The camera supports an auto iris lens.
To install and adjust a Video-type auto iris lens, do the following:
A. Thread the auto iris lens onto the lens mount on the front of the camera.
FIGURE 2.
B. Solder the lens control wires to the connector supplied with the camera.
Pin
1
2
3
4
FIGURE 3.
- 13 -
Name Wire Color
Voltage +
Red
Open
Video
White
Ground
Black
C. Plug the connector into the auto iris jack on the top of the camera.
The connector is polarized and can only be inserted into the jack one way.
D. The E/I switch should be in the "off "position.
E. The A/I switch should be in the "vid" position.
F. Apply power to the camera.
G. Adjust the focus ring on the lens for an optimum picture. If a picture is not
visible, set the lens for proper exposure by adjusting the ALC(automatic
level control) and level on the lens.
The ALC setting can range between AVG(average) or PK(peak).
A midrange setting is appropriate for most applications.
For ALC adjustments:
AVG: To slow the reaction of the lens to changing light, set the range to the
AVG setting to average the video level from the camera. Use when
there are bright spots in the picture such as lights or glare from the sun.
PK: To increase the speed of the lens reaction to the changing light, set
the lens adjustment to PK so the lens will adjust to the brightest or
peak object in the video.
Use this setting if you want to see the brightest object and not the
background objects.
For Level Adjustments:
Adjust the level control for the best picture during the day.
A night adjustment may not provide the proper setting for controlling the
light during the day.
H. Set the back focus of the camera before the final adjustment of the video level.
I. If the auto iris has a gain adjustment:
• If the lens oscillates between open and closed under bright lights, slowly turn
the gain adjustment counter clockwise until the oscillating stops.
• Increase the light getting to the camera by adjusting the level control and
readjusting the gain control as necessary.
• Reset the level control as noted in step E.
- 14 -
3. DC-TYPE AUTO IRIS LENS
The camera supports an auto iris lens.
To install and adjust a DC-type auto iris lens, do the following:
A. Thread the auto iris lens onto the lens mount on the front of the camera.
(see figure 4.)
B. Solder the lens control wires to the connector supplied with the camera.
Pin
1
2
3
4
Name
Damp Coil Damp Coil +
Drive Coil +
Drive Coil -
Wire Color
Blue
Red
White
Green
FIGURE 4.
C. Plug the connector into the auto iris jack on the top of the camera.
The connector is polarized and can only be inserted into jack one way.
D. The E/I switch should be in the "off" position.
E. The A/I switch should be in the "dc" position.
F. Apply power to the camera.
G. Adjust the auto-iris lens for an optimum picture. Use the IRIS (H) control
on the top of the camera for optimum picture quality.
- 15 -
4. BACK FOCUS ADJUSTMENT
For best results, perform back focus adjustments at night or while using a #6 or
#8 welders glass in front of the lens. The focus of the camera will change
slightly if the camera iris was adjusted on a light scene, then changes to a dark
scence. However, the camera will remain in focus if the iris was focused on a
dark scene and the scene lightens.
A. After mounting the lens should be mounted on the camera, then apply power
to the camera.
B. If a picture is visible, focus on the picture. If the picture is not visible, open
the iris on the lens. Open the lens as wide as possible by placing the welder's
glass in front of the lens and forcing the lens to automatically open.
C. When the iris is open to the widest point, readjust the focus for a clear picture.
If a clear picture is not possible, set the focus ring to midrange.
D. Loosen the back focus lock screw.
E. Adjust the focus adjust ring for a clear picture.
F. Tighten the back focus lock screw.
G. Fine tune the focus with the focus ring on the lens.
H. Remove the welders glass from in front of the lens.
I. Adjust the iris of the lens for the best picture quality.
- 16 -
5. ZOOM LENS BACK FOCUS ADJUSTMENT
The objective of back focusing a zoom lens is similar to that of a fixed focal
length camera, except that back focus is also adjusted to maintain the focus
when "zooming" the lens in and out on a scene.
A. Choose an object at the farthest range that you wish to look at with a zoom
lens.
B. Make sure the iris of the lens is wide open. ( Do this by adjusting the camera
at night or use a welder's glass in front of the lens.)
C. Adjust the focus to the stop on the far range.
D. Adjust the zoom on the lens to obtain the widest picture.
E. Loosen the back focus lock screw.
F. Adjust the focus adjust ring for the clearest picture.
G. Tighten the back focus lock screw.
H. Adjust the zoom on the lens to the far telephoto position.
I. Adjust the focus adjust ring for the clearest picture.
J. Adjust the zoom on the lens back to the widest picture.
K. Loosen the back focus lock screw.
L. Readjust the back focus for the clearest picture.
M. Tighten the back focus lock screw.
N. Repeat the previous steps, as many times as necessary, to maintain a clear
picture through the entire zoom range.
- 17 -
TROUBLESHOOTING
If problems occur, verify the installation of the camera with the instructions in this
manual and with other operating equipment.
Isolate the problem to the specific piece of equipment in the system and refer to
the equipment manual for further information.
Problem
No Video
Video, but no control
Possible Solution
1. Verify power to all pieces of equipment in the
system.
2. Verify that the power switches are in the ON
position.
3. Verify that the lens cap has been removed from
the lens or that the iris of the lens is open.
1. Power down the system for one minute, then
turn power back ON.
MAINTENANCE
Preventive maintenance allows detection and correction of minor faults before
they become serious and cause equipment failure.
Every three months, perform the following maintenance:
A. Inspect all connecting cables for deterioration or other damage.
B. Clean components with a clean damp cloth.
C. Verify that all the mounting hardware is secure.
- 18 -
SPECIFICATIONS
Image sensor
Picture Element (H x V)
Image sensor area (H x V)
Resolution
Min. scene illumination
S/N Ratio
Shutter speed
Line phase range
Sync system
Signal format
Scanning frequency(H x V)
Video output
Power requirements
Power consumption
Connector - Video out
- Auto iris
Lens mount
- 19 -
Dimension(WxHxD)
Weight
Ambient temperature
Ambient humidity
Funtion - E/I
- A/I
- IRIS
- PHASE
Printed in KOREA
Rev - Part 50300954
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement