HP | 493960-221 | Specifications | HP 493960-171

HP Compaq 2230s Notebook PC
Maintenance and Service Guide
Document Part Number: 482392-002
November 2008
This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides
comprehensive information on identifying computer features, components, and spare parts; troubleshooting
computer problems; and performing computer disassembly procedures.
© Copyright 2008 Hewlett-Packard Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel, Core, and Celeron are
trademarks of Intel Corporation in the U.S. and other countries. Microsoft, Windows, and Windows Vista are U.S. registered trademarks
of Microsoft Corporation. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in
the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Second Edition: November 2008
First Edition: August 2008
Document Part Number: 482392-002
Safety warning notice
Å
WARNING: To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly
on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface,
such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow
the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of
Information Technology Equipment (IEC 60950).
Contents
1 Product description
2 External component identification
Display components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Top components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pointing devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Buttons and fingerprint reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Left-side components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Right-side components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bottom components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1
2–2
2–2
2–3
2–5
2–6
2–7
2–7
2–8
2–9
3 Illustrated parts catalog
Serial number location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
Computer major components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Cable Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
Mass storage devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
Miscellaneous parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
Sequential part number listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–12
4 Removal and replacement procedures
Preliminary replacement requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Service considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Grounding guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Unknown user password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–4
Component replacement procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Computer feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–8
Memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–10
WLAN module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12
Optical drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–16
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–18
Top cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–21
Speaker assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–25
Display assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–26
Audio board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–32
Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–33
Contents
iv
System board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RTC battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modem module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bluetooth module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–34
4–36
4–37
4–38
4–40
4–42
5 Computer Setup
Starting Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating and selecting in Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring factory settings in Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Computer Setup menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–1
5–1
5–2
5–2
5–2
5–3
5–3
5–4
6 Specifications
Computer specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1-inch, WXGA display specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hard drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVD/CD-RW Combo Drive specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blu-ray ROM DVD±RW SuperMulti DL Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVD±RW SuperMulti Double-Layer Drive specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVD-ROM Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System DMA specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System interrupt specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System I/O address specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System memory map specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6–1
6–2
6–2
6–3
6–3
6–4
6–4
6–5
6–5
6–6
6–8
7 Screw listing
Phillips PM1.5×3.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–1
Phillips PM2.0×3.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–3
Phillips PM2.0×4.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–4
Phillips PM2.0×5.0 captive screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–5
Phillips PM2.0×3.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–6
Phillips PM2.0×6.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–7
Phillips PM2.0×5.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–8
Phillips PM2.0×7.0 captive screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–9
Phillips PM2.0×10.0 captive screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–10
Phillips PM2.5×10.0 captive screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–11
Phillips PM3.0×3.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–12
Phillips PM3.0×4.0 screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–13
Phillips T2.0×2.0BH screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–14
Torx T8M2.5×6.0 slotted screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–15
8 Backup and recovery
Backup and recovery in Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backup tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
8–1
8–1
8–2
8–2
v
Backup and recovery in Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–4
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–4
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–5
9 Connector pin assignments
Audio-in (microphone). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio-out (headphone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ-11 (modem). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ-45 (network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Universal Serial Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9–1
9–1
9–2
9–3
9–4
9–4
9–5
10 Power cord set requirements
Requirements for all countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–1
Requirements for specific countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–2
11 Recycling
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–1
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–1
Index
Contents
vi
1
Product description
Category
Description
Product name
HP Compaq 2230s Notebook PC
Processors
Intel® Core™2 Duo processors:
Models with
GL40 system
board
Models with
GM45 system
board
X
X
■ T9600 2.8-GHz processor, 6-MB L2 cache, 1066-MHz
front side bus (FSB)
X
■ T9400 2.53-GHz processor, 6-MB L2 cache, 1066-MHz
FSB
X
■ P9500 2.53-GHz processor, 6-MB L2 cache, 1066-MHz
FSB
X
■ P8700 2.53-GHz processor, 3-MB L2 cache, 1066-MHz
FSB
X
■ P8600 2.4-GHz, 3-MB L2 cache, 1066-MHz FSB
X
■ P8400 2.26-GHz processor, 3-MB L2 cache, 1066-MHz
FSB
X
■ P7370 2.0-GHz processor, 3-MB L2 cache, 1066-MHz
FSB (for use with Intel WLAN only)
X
Intel Core Duo processors:
■ P5870 2.0-GHz processor, 2-MB L2 cache, 800-MHz FSB
(for use with no-WLAN option or Intel WLAN only)
X
■ P5670 1.8-GHz processor, 2-MB L2 cache, 800-MHz FSB
(for use with no-WLAN option or Intel WLAN only)
X
■ T3400 2.16-GHz processor, 1-MB L2 cache,
667-MHz FSB
X
X
■ T3200 2.0-GHz processor, 1-MB L2 cache, 667-MHz FSB
X
X
Intel Celeron®-M processors:
■ 585 2.16-GHz processor, 1-MB L2 cache, 667-MHz FSB
X
■ 575 2.0-GHz processor, 1-MB L2 cache, 667-MHz FSB
X
Intel Celeron-T processors:
Chipset
■ T1700 1.83-GHz processor, 1-MB L2 cache,
667-MHz FSB
X
■ T1600 1.66-GHz processor, 1-MB cache, 667-MHz FSB
X
Northbridge: Intel GL40
X
Northbridge: Intel GM45
Southbridge: Intel ICH9M
X
X
X
(Continued)
Product description
1–1
Category
Description
Models with
GL40 system
board
Models with
GM45 system
board
Graphics
Intel Unified Memory Architecture (UMA) graphics
subsystem integrated with shared system memory
(dynamically allocated)
X
X
Panel
12.1-inch WXGA panel (1280 × 800)
X
X
12.1-inch WXGA panel (1280 x 800) with integrated webcam
X
X
12.1-inch WXGA panel (1280 x 800) with BrightView
X
X
12.1-inch WXGA panel (1280 x 800) with BrightView and
integrated webcam
X
X
2 customer-accessible/upgradable memory module slots
X
X
Supports dual-channel memory
X
X
Supports up to 4 GB of system RAM
X
X
■ 4096-MB total system memory (2048 x 2, dual-channel)
X
X
■ 3072-MB total system memory (2048 + 1024)
X
X
■ 2048-MB total system memory (1024 × 2, dual-channel)
X
X
■ 2048-MB total system memory (2048 × 1)
X
X
■ 1024-MB total system memory (1024 × 1)
X
X
Supports 9.5-mm, 2.5-inch hard drives
X
X
Customer-accessible
X
X
Serial ATA
X
X
■ 320-GB, 5400-rpm
X
X
■ 250-GB, 5400-rpm
X
X
■ 160-GB, 7200-rpm
X
X
■ 160-GB, 5400-rpm
X
X
■ 120-GB, 5400-rpm
X
X
Fixed (removal of 1 screw required)
X
X
Customer-accessible
X
X
Serial ATA
X
X
Supports no-optical-drive option
X
X
■ DVD/CD-RW Combo Drive
X
X
■ DVD-ROM Drive
X
X
■ DVD±RW SuperMulti Double-Layer Drive with LightScribe
X
X
All display assemblies include 2 wireless local area network
(WLAN) antennae
Memory
PC2-6400, 800-MHz, DDR2
Supports the following configurations:
Hard drives
Supports the following drives:
Optical drives
Supports the following drives:
■ Blu-ray ROM DVD±RW SuperMulti DL Drive
Diskette drive
Supports external USB diskette drive only
X
X
X
(Continued)
Product description
1–2
Category
Description
Models with
GL40 system
board
Models with
GM45 system
board
Microphone
Integrated mono microphone
X
X
Audio
Azalia audio
X
X
2 speakers
X
X
56K V.92 1.5-inch data/fax modem with digital line guard
X
X
Intel Broadcom 88E8072 10/100/1000 network interface
card (NIC)
X
X
Ethernet cable included
X
X
2 wireless antennae built into display assembly
X
X
Supports no-WLAN option
X
X
■ Broadcom 802.11a/b/g/n
X
X
■ Intel 802.11a/b/g/n
X
X
■ Broadcom 802.11b/g
X
X
■ Intel 802.11a/b/g
X
X
Support for no-WPAN option
X
X
Broadcom Bluetooth
X
X
One ExpressCard slot, supporting optional ExpressCard/34
cards
X
X
Media Card Reader supporting MMC, SD, and SD High
Capacity digital cards
X
X
Audio-in (mono microphone)
X
X
Audio-out (stereo headphone)
X
X
HDMI
X
X
RJ-11 (modem)
X
X
RJ-45 (Ethernet, includes link and activity lights)
X
X
USB (3)
X
X
VGA (Dsub 15-pin) supporting 1600 × 1200 external
resolution at 75 GHz (hot plug/unplug with auto-detect)
X
X
Multi-pin AC power
X
X
Docking
None
X
X
Keyboard/pointing
devices
Spill-resistant full-size keyboard
X
X
TouchPad with 2 TouchPad buttons
X
X
Supports 2-way scroll
X
X
Taps enabled as default
X
X
Windows Vista® Hardware Start Button
X
X
Modem
Modem cable is not included
Ethernet
Wireless
Integrated WLAN options by way of wireless module:
Support for the following WLAN formats:
Integrated personal area network (PAN) options by way
of Bluetooth® module:
External media card
Ports
(Continued)
Product description
1–3
Category
Description
Models with
GL40 system
board
Models with
GM45 system
board
Power requirements
65-W AC adapter with localized and pointing stick cable plug
support (3-wire plug with ground pin, supports 3-pin DC
connector)
X
X
4-cell, 37-Wh Li-ion battery
X
X
8-cell, 73-Wh Li-ion battery
X
X
Security
Security cable slot
X
X
Operating system
Preinstalled:
Windows Vista® Home Basic 32
X
X
Windows Vista Home Premium 32
X
X
Windows Vista Business 32
X
X
Windows Vista Business (with downgrade to Windows® XP
Professional)
X
X
FreeDOS
X
X
Red Flag Linux
X
X
AC adapter
X
X
Battery (system)
X
X
Hard drive
X
X
Memory module
X
X
Optical drive
X
X
WLAN module
X
X
Serviceability
Product description
End-user replaceable parts:
1–4
2
External component identification
Display components
Item
Component
Function
1
Wireless antennae (2)*
Send and receive wireless signals to communicate with WLANs.
2
Internal microphones (2)
Record sound.
3
Webcam light (select models only)
On: The webcam is in use.
4
Webcam (select models only)
Records audio and video and captures still photographs.
*The antennae are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennae free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety and
Environmental Notices that applies to your country or region. These notices are located in Help and Support.
External component identification
2–1
Top components
Pointing devices
Item
Component
Function
1
TouchPad*
Moves the pointer and selects or activates items on the screen.
2
Left TouchPad button*
Functions like the left button on an external mouse.
3
Right TouchPad button*
Functions like the right button on an external mouse.
4
Vertical scroll zone
Scrolls up or down.
*This table describes factory settings. View or change device preferences as follows:
■ In Windows Vista, select Start > Control Panel > Hardware and Sound > Mouse.
■ In Windows XP, select Start > Control Panel > Printers and Other Hardware > Mouse.
External component identification
2–2
Buttons and fingerprint reader
Item
Component
Function
1
Power button
■ When the computer is off, press the button to turn on the computer.
■ When the computer is on, press the button to shut down the computer.
■ When the computer is in Standby or the Sleep state, press the button
briefly to exit Standby or the Sleep state.
■ When the computer is in Hibernation, press the button briefly to exit
Hibernation.
If the computer has stopped responding and Windows® shutdown
procedures are ineffective, press and hold the power button for at least
5 seconds to turn off the computer.
To learn more about power settings, follow these steps:
■ In Windows Vista, select Start > Control Panel > Mobile PC > Power
Options.
■ In Windows XP, select Start > Control Panel > System and
Maintenance > Power Options.
2
Info button
Launches Info Center, which provides shortcuts, such as the
following:
■ HP 3D DriveGuard—Controls settings for software that protects the hard
drive by parking the drive when the computer is dropped or moved.
■ HP Software Setup—Installs preloaded applications to make them
accessible to the user.
(Continued)
External component identification
2–3
Item
Component
Function
3
Presentation button
Opens the Presentation Options window, where you can start a frequently
used presentation, file, program, or Web site. You can also adjust display
setting for optimum viewing.
4
Wireless button
Turns the wireless feature on or off, but does not establish a wireless
connection.
must set up or access a wireless network to establish a wireless
✎ You
connection.
5
Volume mute button
Mutes and restores speaker sound.
6
Volume down button
Decreases speaker volume.
7
Volume scroll zone
Adjusts speaker volume. Slide your finger to the left to decrease volume and
to the right to increase volume.
8
Volume up button
Increases speaker volume.
9
Fingerprint reader
Allows a fingerprint logon to Windows, instead of a password logon.
External component identification
2–4
Keys
Item
Component
Function
1
esc key
Displays system information when pressed in combination with the fn key.
2
fn key
Executes frequently used system functions when pressed in combination with
a function key or the esc key.
3
Windows logo key
Displays the Windows Start menu.
4
Windows applications key
Displays a shortcut menu for items beneath the pointer.
5
Embedded numeric keypad keys
Can be used like the keys on an external numeric keypad.
6
Function keys
Execute frequently used system functions when pressed in combination with
the fn key.
External component identification
2–5
Lights
Item
Component
Function
1
Caps lock light
On: Caps lock is on.
2
Battery light (beside power connector) ■ Amber: A battery is charging.
■ Green: A battery is close to full charge capacity.
■ Blinking amber: A battery that is the only available power source has
reached a low battery level. When the battery reaches a critical battery
level, the battery light begins blinking rapidly.
■ Off: If the computer is plugged into an external power source, the light turns
off when all batteries in the computer are fully charged. If the computer is
not plugged into an external power source, the light stays off until the
battery reaches a low battery level.
3
Power light
■ On: The computer is on.
■ Blinking: The computer is in the Sleep state.
■ Blinking rapidly: An AC adapter with a higher power rating should be
connected.
■ Off: The computer is off or in Hibernation.
4
Info button light
■ On: The Info Center is launched.
5
Presentation button light
■ On: Presentation Options is on.
6
Wireless light
■ Blue: An integrated wireless device, such as a wireless local area network
(WLAN) device, an HP Mobile Broadband Module, and/or a Bluetooth®
device, is on.
■ Amber: All wireless devices are off.
7
Volume mute light
■ Off: Computer sound is on.
■ On: Computer sound is off.
8
Volume down light
Blinking: The volume scroll zone is being used to decrease speaker volume.
9
Volume up
Blinking: The volume scroll zone is being used to increase speaker volume.
External component identification
2–6
Front components
Item
Component
Function
1
Drive light
■ Blinking green: The hard drive or optical drive is being accessed.
■ Amber (select models only): HP 3D DriveGuard has temporarily parked the
hard drive.
2
Audio-in (microphone) jack
Connects an optional computer headset microphone, stereo array
microphone, or monaural microphone.
3
Audio-out (headphone) jack
Produces sound when connected to optional powered stereo speakers,
headphones, ear buds, a headset, or television audio.
Left-side components
Item
Component
Function
1
Battery light
■ Amber: A battery is charging.
■ Turquoise: A battery is close to full charge capacity.
■ Blinking amber: A battery that is the only available power source has
reached a low battery level. When the battery reaches a critical battery
level, the battery light begins blinking rapidly.
■ Off: If the computer is plugged into an external power source, the light turns
off when all batteries in the computer are fully charged. If the computer is
not plugged into an external power source, the light stays off until the
battery reaches a low battery level.
2
Power connector
Connects an AC adapter.
3
RJ-45 (network) jack
Connects a network cable.
4
RJ-11 (modem) jack
Connects a modem cable.
5
USB port
Connects an optional USB device.
6
Optical drive
Reads optical discs and, on select models, also writes to optical discs.
External component identification
2–7
Right-side components
Item
Component
Function
1
ExpressCard slot
Supports optional ExpressCard/34 cards.
2
Memory Card Reader
(select models only)
Supports the following optional digital card formats:
■ MultiMediaCard
■ MultiMediaCard Plus
■ Secure Digital Memory Card
■ Secure Digital High Capacity Memory Card
3
HDMI port (select models only)
Connects an optional video or audio device, such as a high-definition
television or any compatible digital or audio component.
4
USB ports (2)
Connects an optional USB device.
5
External monitor port
Connects an external VGA monitor or projector.
6
Vent
Enables airflow to cool internal components.
computer fan starts up automatically to cool internal components
✎ The
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
7
Security cable slot
Attaches an optional security cable to the computer.
security cable is designed to act as a deterrent, but it may not
✎ The
prevent the computer from being mishandled or stolen.
External component identification
2–8
Bottom components
Item
1
Component
Function
Vents (3)
Enables airflow to cool internal components.
computer fan starts up automatically to cool internal components
✎ The
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
2
Hard drive bay
Holds the hard drive and two memory module slots.
3
Battery bay
Holds the battery.
4
Battery release latch
Releases the battery from the battery bay.
5
Wireless module compartment
Contains a WLAN module slot.
Ä
External component identification
To prevent an unresponsive system, use only a wireless module
authorized for use in the computer by the governmental agency that
regulates wireless devices in your country or region. If you install the
module and then receive a warning message, remove the module to
restore computer functionality, and then contact technical support
through Help and Support.
2–9
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model number located on
the bottom of the computer. The service tag provides the following information.
Item
Component
Description
1
Product name
This is the product name affixed to the front of the computer.
2
Serial number (s/n)
This is an alphanumeric identifier that is unique to each product.
3
Part number/Product number (p/n)
This number provides specific information about the product's
hardware components. The part number helps a service
technician to determine what components and parts are needed.
4
Model description
This is the number used to locate documents, drivers, and
support for the computer.
5
Warranty period
This number describes the duration of the warranty period for the
computer.
Illustrated parts catalog
3–1
Computer major components
Illustrated parts catalog
3–2
Item
Description
(1)
Display assembly (include 2 WLAN antenna transceivers and cables, nameplate, and logo)
Spare Part Number
12.1-inch, WXGA display assembly
493186-001
12.1-inch, WXGA display assembly with integrated webcam
501932-001
12.1-inch, WXGA BrightView display assembly
493187-001
12.1-inch, WXGA BrightView display assembly with integrated webcam
501933-001
Display internal components:
(2)
Webcam with cable
492159-001
Display bezel
495015-001
Display bezel with webcam
501934-001
Display inverter
493193-001
Display hinges
493192-001
Display hinge covers
495016-001
Display cables (includes display, microphone, and antenna cables)
493189-001
Display nameplate
493191-001
Display enclosure
493188-001
Display Miscellaneous Kit (includes rubber feet, screw covers, and hinge cover)
493190-001
Keyboard (includes keyboard cable)
For use in Belgium
493960-A41
For use in Canada
493960-121
For use in the Czech Republic
493690-221
For use in Denmark
493960-081
For use in France
493960-051
For use in Greece
493960-DJ1
For use in Germany
493960-041
For use in Hungary
493960-211
For use in Iceland
493960-DD1
For international use
493960-B31
For use in Italy
493960-061
For use in Israel
493960-BB1
For use in Japan
493960-291
For use in Latin America
493960-161
For use in Norway
493960-091
For use in Portugal
493960-131
For use in Russia
493960-251
For use in Saudi Arabia
493960-171
For use in Slovakia
493960-231
For use in Slovenia
493960-BA1
For use in Spain
493960-071
For use in Sweden and Finland
493960-B71
(Continued)
Illustrated parts catalog
3–3
Item
Description
Spare Part Number
For use in Switzerland
493960-BG1
For use in South Korea
493960-AD1
For use in Taiwan
493960-AB1
For use in Thailand
493960-281
For use in Turkey
493960-141
For use in the United Kingdom
493960-031
For use in the United States
493960-001
(3)
Speaker assembly
493273-001
(4)
Top cover (includes TouchPad and cable, LED board and cable, and switch cover)
493278-001
(5)
Modem module cable (includes RJ-11 jack)
modem module cable is included in the Cable Kit, spare part number
✎ The
493275-001. See “Cable Kit” on page 3-8 for more Cable Kit information.
(6)
Modem module
modem module spare part kit does not include a modem module cable. The
✎ The
modem module cable is included in the Cable Kit, spare part number 493275-001.
See “Cable Kit” on page 3-8 for more Cable Kit information.
For use in Australia and New Zealand
461749-011
For use in all countries or regions except Australia and New Zealand
461749-001
(7)
Audio board
493272-001
(8)
System board
GM45 (includes RTC battery and replacement thermal material)
493185-001
GL40 (includes RTC battery and replacement thermal material)
504446-001
Plastics Kit (see “Plastics Kit” on page 3-9 for more Plastics Kit spare part information)
493274-001
(9a)
ExpressCard slot bezel
(9b)
WLAN module compartment cover
(9c)
Hard drive compartment cover
(10)
Bluetooth module
398393-002
The Bluetooth module spare part kit does not include a Bluetooth module cable. The
✎ Bluetooth
module cable is included in the Cable Kit, spare part number 493275-001.
See “Cable Kit” on page 3-8 for more Cable Kit information.
(11)
RTC battery
449137-001
(12)
Fan
493269-001
(Continued)
Illustrated parts catalog
3–4
Item
Description
(13)
Processor (includes replacement thermal material)
Spare Part Number
Intel Core2 Duo processors (6-MB L2 cache, 1066-MHz FSB):
■ T9600 2.8-GHz processor
486257-001
■ T9400 2.53-GHz processor
486256-001
■ P9500 2.53-GHz processor
496458-001
Intel Core2 Duo processors (3-MB L2 cache, 1066-MHz FSB):
■ P8700 2.53-GHz processor
512585-001
■ P8600 2.4-GHz processor
486255-001
■ P8400 2.26-GHz processor
486254-001
■ P7370 2.0-GHz processor (for use with Intel WLAN only)
507966-001
Intel Core Duo processors (2-MB L2 cache, 800-MHz FSB):
■ P5870 2.0-GHz processor
500771-001
■ P5670 1.8-GHz processor
500770-001
Intel Core Duo processors (1-MB L2 cache, 667-MHz FSB):
■ T3400 2.16-GHz processor
509061-001
■ T3200 2.0-GHz processor
509060-001
Intel Celeron-M processors (1-MB L2 cache, 667-MHz FSB):
■ 585 2.16-GHz processor (for use with no WLAN support or Intel WLAN only)
490337-001
■ 575 2.0-GHz processor (for use with no WLAN support or Intel WLAN only)
490336-001
Intel Celeron-T processor (1-MB L2 cache, 667-MHz FSB):
■ T1700 1.83-GHz processor
509059-001
■ T1600 1.66-GHz processor
509058-001
(14)
Thermal module (includes heat sink and thermal material)
493270-001
(15)
Battery
(16)
(17)
4-cell, 37-Wh
493202-001
8-cell, 73-Wh
501935-001
Base enclosure (includes rubber feet)
493271-001
Rubber Kit (not illustrated, contains 5 computer feet)
493276-001
Optical drive (includes optical drive bezel and bracket)
DVD/CD-RW Combo Drive
493200-001
DVD-ROM Drive
493201-001
DVD±RW SuperMulti Double-Layer Drive with LightScribe
493961-001
Blu-ray ROM DVD±RW SuperMulti DL Drive
497536-001
(Continued)
Illustrated parts catalog
3–5
Item
Description
(18)
WLAN module
Spare Part Number
Broadcom 802.11a/b/g/n WLAN modules:
■ For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and
the United States
487330-001
■ For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia,
Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East
Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji,
Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia,
Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and
Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia,
St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,
Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu,
Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan,
Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
487330-002
Broadcom 802.11b/g WLAN modules:
■ For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and
the United States
459263-001
■ For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia,
Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East
Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji,
Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia,
Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and
Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia,
St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,
Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu,
Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan,
Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
459263-002
(Continued)
Illustrated parts catalog
3–6
Item
Description
Spare Part Number
Intel 802.11a/b/g/n WLAN module:
■ For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and
the United States
480985-001
Intel 802.11a/b/g WLAN module:
■ For use in Pakistan, Russia, and Ukraine
(19)
(20)
482957-001
Memory modules
2048-MB
493195-001
1024-MB
493194-001
Hard drive (includes hard drive bracket)
320-GB, 5400-rpm
493199-001
250-GB, 5400-rpm
493198-001
160-GB, 7200-rpm
513695-001
160-GB, 5400-rpm
493197-001
120-GB, 5400-rpm
493196-001
Cable Kit (not illustrated)
493275-001
Illustrated parts catalog
3–7
Cable Kit
Item
Description
Spare part number
Cable Kit:
493275-001
1
Bluetooth module cable
2
Modem module cable (includes RJ-11 jack)
Illustrated parts catalog
3–8
Plastics Kit
Item
Description
Spare part number
Plastics Kit:
493274-001
1
Hard drive compartment cover (includes one captive screw, secured by a C-clip)
2
Wireless module compartment cover (includes one captive screw, secured by
a C-clip)
3
ExpressCard slot bezel
4
SD card bezel
5
Base enclosure screw covers (4 covers, 2 sizes)
Illustrated parts catalog
3–9
Mass storage devices
Item
1
2
Description
Spare part number
Optical drive (includes bezel)
320-GB, 5400-rpm
493199-001
250-GB, 5400-rpm
493198-001
160-GB, 7200-rpm
513695-001
160-GB, 5400-rpm
493197-001
120-GB, 5400-rpm
493196-001
Hard drive (includes bracket)
DVD/CD-RW Combo Drive
493200-001
DVD-ROM Drive
493201-001
DVD±RW SuperMulti Double-Layer Drive with LightScribe
493961-001
Blu-ray ROM DVD±RW SuperMulti DL Drive
497536-001
Illustrated parts catalog
3–10
Miscellaneous parts
Description
Spare part number
65-W AC adapter
463958-001
Power cords:
For use in Argentina
490371-D01
For use in Denmark
490371-081
For use in Europe
490371-021
For use in Israel
490371-BB1
For use in North America
490371-001
For use in the United Kingdom and Singapore
490371-031
For use in the People’s Republic of China
490371-AA1
For use in Australia
490371-011
For use in India
490371-D61
For use in Italy
490371-061
For use in Japan
490371-291
For use in South Africa
490371-AR1
For use in South Korea
490371-AD1
For use in Switzerland
490371-111
For use in Taiwan
490371-AB1
Screw Kit
■ Torx T8M2.5x6.0 screw (14)
■ Phillips M2.0x4.0 screw (5)
■ Phillips M2.5x5.0 screw (7)
■ Phillips M2.0x3.0 screw (3)
■ Phillips M2.5x2.5 screw (4)
■ Phillips M2.0x2.0 screw (3)
493277-001
Illustrated parts catalog
3–11
Sequential part number listing
Spare part number
Description
398393-002
Bluetooth module
Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
✎ The
module cable is included in the Cable Kit, spare part number 493275-001.
449137-001
RTC battery
459263-001
Broadcom 802.11a/b/g WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico,
the U.S. Virgin Islands, and the United States
459263-002
Broadcom 802.11a/b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas,
Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia
and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, People's Republic of
China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark,
Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial
Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal,
Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St.
Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo,
Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United
Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
461749-001
Modem module for use in all countries or regions except Australia and New Zealand
461749-011
Modem module for use in Australia and New Zealand
463958-001
65-W AC adapter
480985-001
Intel 802.11a/b/g WLAN modules for use in Canada, the Cayman Islands, Guam, Puerto Rico, the
U.S. Virgin Islands, and the United States
482957-001
Intel 802.11a/b/g WLAN module for use in Pakistan, Russia, and Ukraine
486254-001
Intel Core2 Duo processor (3-MB L2 cache, 1066-MHz FSB), P8400 2.26-GHz (includes
replacement thermal material)
486255-001
Intel Core2 Duo processor (3-MB L2 cache, 1066-MHz FSB), P8600 2.4-GHz (includes replacement
thermal material)
486256-001
Intel Core2 Duo processor (6-MB L2 cache, 1066-MHz FSB), T9400 2.53-GHz (includes
replacement thermal material)
486257-001
Intel Core2 Duo processor (6-MB L2 cache, 1066-MHz FSB), T9600 2.8-GHz (includes replacement
thermal material)
487330-001
Intel 802.11a/b/g/n WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico, the
U.S. Virgin Islands, and the United States
(Continued)
Illustrated parts catalog
3–12
Spare part number
Description
487330-002
Intel 802.11a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua
and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, People's Republic of China,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark,
Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial
Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal,
Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St.
Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo,
Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United
Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
490336-001
Intel Celeron-M processor (1-MB L2 cache, 667-MHz FSB), 575 2.0-GHz (includes replacement
thermal material)
490337-001
Intel Celeron-M processor (1-MB L2 cache, 667-MHz FSB), 585 2.16-GHz (includes replacement
thermal material)
490371-001
Power cord for use in North America
490371-011
Power cord for use in Australia
490371-021
Power cord for use in Europe
490371-031
Power cord for use in the United Kingdom and Singapore
490371-061
Power cord for use in Italy
490371-081
Power cord for use in Denmark
490371-111
Power cord for use in Switzerland
490371-291
Power cord for use in Japan
490371-AA1
Power cord for use in the People’s Republic of China
490371-AB1
Power cord for use in Taiwan
490371-AD1
Power cord for use in South Korea
490371-AR1
Power cord for use in South Africa
490371-BB1
Power cord for use in Israel
490371-D01
Power cord for use in Argentina
490371-D61
Power cord for use in India
492159-001
Webcam with cable
493185-001
System board, GM45 (includes RTC battery and replacement thermal material)
493186-001
12.1-inch, WXGA display assembly
493187-001
12.1-inch, WXGA BrightView display assembly
493188-001
Display enclosure
(Continued)
Illustrated parts catalog
3–13
Spare part number
Description
493189-001
Display cables (includes display, microphone, and antenna cables)
493190-001
Display Miscellaneous Kit (includes rubber feet, screw covers, and hinge cover)
493191-001
Display nameplate
493192-001
Display hinges
493193-001
Display inverter
493194-001
Memory module, 1024-MB
493195-001
Memory module, 2048-MB
493196-001
Hard drive, 120-GB, 5400-rpm
493197-001
Hard drive, 160-GB, 5400-rpm
493198-001
Hard drive, 250-GB, 5400-rpm
493199-001
Hard drive, 320-GB, 5400-rpm
493200-001
DVD/CD-RW Combo Drive (includes drive bezel and bracket)
493201-001
DVD-ROM Drive (includes drive bezel and bracket)
493202-001
Battery, 4-cell, 37-Wh
493269-001
Fan
493270-001
Thermal module (includes heat sink and thermal material)
493271-001
Base enclosure (includes rubber feet)
493272-001
Audio board
493273-001
Speaker assembly
493274-001
Plastics Kit (see “Plastics Kit” on page 3-9 for more Plastics Kit spare part information)
493275-001
Cable Kit (see “Cable Kit” on page 3-8 for more Cable Kit information)
493276-001
Rubber Kit (contains 5 computer feet)
493277-001
Screw Kit
493278-001
Top cover (includes TouchPad and cable, LED board and cable, and switch cover)
493960-001
Keyboard for use in the United States
493960-031
Keyboard for use in the United Kingdom
493960-041
Keyboard for use in Germany
493960-051
Keyboard for use in France
493960-061
Keyboard for use in Italy
493960-071
Keyboard for use in Spain
493960-081
Keyboard for use in Denmark
493960-091
Keyboard for use in Norway
493960-121
Keyboard for use in Canada
493960-131
Keyboard for use in Portugal
493960-141
Keyboard for use in Turkey
493960-161
Keyboard for use in Latin America
493960-171
Keyboard for use in Saudi Arabia
493960-211
Keyboard for use in Hungary
(Continued)
Illustrated parts catalog
3–14
Spare part number
Description
493960-221
Keyboard for use in the Czech Republic
493960-231
Keyboard for use in Slovakia
493960-251
Keyboard for use in Russia
493960-281
Keyboard for use in Thailand
493960-291
Keyboard for use in Japan
493960-A41
Keyboard for use in Belgium
493960-AB1
Keyboard for use in Taiwan
493960-AD1
Keyboard for use in South Korea
493960-B31
Keyboard for international use
493960-B71
Keyboard for use in Sweden and Finland
493960-BA1
Keyboard for use in Slovenia
493960-BB1
Keyboard for use in Israel
493960-BG1
Keyboard for use in Switzerland
493960-DD1
Keyboard for use in Iceland
493960-DJ1
Keyboard for use in Greece
493961-001
DVD±RW SuperMulti Double-Layer Drive with LightScribe (includes drive bezel and bracket)
495015-001
Display bezel
495016-001
Display hinge covers
496458-001
Intel Core2 Duo processor (6-MB L2 cache, 1066-MHz FSB), P9500 2.53-GHz (includes
replacement thermal material)
497536-001
Blu-ray ROM DVD±RW SuperMulti DL Drive (includes drive bezel and bracket)
500770-001
Intel Core Duo processor (2-MB L2 cache, 800-MHz FSB), P5670 1.8-GHz (includes replacement
thermal material)
500771-001
Intel Core Duo processor (2-MB L2 cache, 800-MHz FSB), P5870 2.0-GHz (includes replacement
thermal material)
501932-001
12.1-inch, WXGA display assembly with integrated webcam
501933-001
12.1-inch, WXGA BrightView display assembly with integrated webcam
501934-001
Display bezel with webcam
501935-001
Battery, 8-cell, 73-Wh
504446-001
System board, GL40 (includes RTC battery and replacement thermal material)
507966-001
Intel Core2 Duo processor (3-MB L2 cache, 1066-MHz FSB), P7370 2.0-GHz (includes replacement
thermal material)
509058-001
Intel Celeron-T processor (1-MB L2 cache, 667-MHz FSB), T1600 1.66-GHz (includes replacement
thermal material)
509059-001
Intel Celeron-T processor (1-MB L2 cache, 667-MHz FSB), T1700 1.83-GHz (includes replacement
thermal material)
509060-001
Intel Core Duo processor (1-MB L2 cache, 667-MHz FSB), T3200 2.0-GHz (includes replacement
thermal material)
509061-001
Intel Core Duo processor (1-MB L2 cache, 667-MHz FSB), T3400 2.16-GHz (includes replacement
thermal material)
512585-001
Intel Core2 Duo processor (3-MB L2 cache, 1066-MHz FSB), P8700 2.53-GHz (includes
replacement thermal material)
513695-001
Hard drive, 160-GB, 7200-rpm
Illustrated parts catalog
3–15
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
■
Flat-bladed screwdriver
■
Magnetic screwdriver
■
Phillips P0 and P1 screwdrivers
■
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly and
assembly procedures.
you remove each subassembly from the computer, place the subassembly (and all accompanying screws)
✎ As
away from the work area to prevent damage.
Plastic parts
Ä
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the
plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Cables and connectors
Ä
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly
process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the
cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid
bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or
snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.
Removal and replacement procedures
4–1
Drive handling
Ä
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a
drive, or loss of information, observe these precautions:
■ Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in
Hibernation, turn the computer on, and then shut it down through the operating system.
■ Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid touching the
connector.
■ Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure that the optical
drive tray is closed.
■ Handle drives on surfaces covered with at least one inch of shock-proof foam.
■ Avoid dropping drives from any height onto any surface.
■ After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
■ Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
■ Avoid exposing a drive to temperature extremes or liquids.
■ If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging and label
the package "FRAGILE."
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the
degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD
contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and may work perfectly throughout a normal cycle.
Or the device may function normally for a while, and then degrade in the internal layers, reducing its life
expectancy.
Ä
CAUTION: To prevent damage to the computer when you are removing or installing internal components, observe these
precautions:
■ Keep components in their electrostatic-safe containers until you are ready to install them.
■ Use nonmagnetic tools.
■ Before touching an electronic component, discharge static electricity by using the guidelines described in this section.
■ Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
■ If you remove a component, place it in an electrostatic-safe container.
Removal and replacement procedures
4–2
The following table shows how humidity affects the electrostatic voltage levels generated by different activities.
Ä
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
■
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
■
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
■
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
■
Place items on a grounded surface before removing items from their containers.
■
Always be properly grounded when touching a component or assembly.
■
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
■
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to avoid static
charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
■
Cover the workstation with approved static-shielding material.
■
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and
equipment.
■
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
■
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials.
■
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and Styrofoam.
■
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items
only at static-free workstations.
■
Avoid contact with pins, leads, or circuitry.
■
Turn off power and input signals before inserting or removing connectors or test equipment.
Removal and replacement procedures
4–3
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
■
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a
minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly
against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a
wrist strap.
■
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at
standing workstations and are compatible with most types of shoes or boots. On conductive floors or
dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the
operator and ground. To be effective, the conductive strips must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
■
Antistatic tape
■
Antistatic smocks, aprons, and sleeve protectors
■
Conductive bins and other assembly or soldering aids
■
Nonconductive foam
■
Conductive tabletop workstations with ground cords of one megohm resistance
■
Static-dissipative tables or floor mats with hard ties to the ground
■
Field Service Kits
■
Static awareness labels
■
Material-handling packages
■
Nonconductive plastic bags, tubes, or boxes
■
Metal tote boxes
■
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the password:
✎ These steps also clear CMOS.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the real-time clock (RTC) battery (see “RTC battery” on page 4-36).
6. Wait approximately 5 minutes.
7. Replace the RTC battery and reassemble the computer.
Removal and replacement procedures
4–4
8. Connect AC power to the computer. Do not reinsert any batteries at this time.
9. Turn on the computer.
All passwords and all CMOS settings have been cleared.
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 71 screws, in 14 different sizes, that must be removed, replaced, or loosened when servicing
the computer. Make special note of each screw size and location during removal and replacement.
Serial number
When ordering parts or requesting information, provide the computer serial number and model description
provided on the service tag.
Item
Component
Description
1
Product name
This is the product name affixed to the front of the computer.
2
Serial number (s/n)
This is an alphanumeric identifier that is unique to each product.
3
Part number/Product number (p/n)
This number provides specific information about the product's
hardware components. The part number helps a service
technician to determine what components and parts are needed.
4
Model description
This is the number used to locate documents, drivers, and
support for the computer.
5
Warranty period
This number describes the duration of the warranty period for the
computer.
Removal and replacement procedures
4–5
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Plastics Kit, spare part number
493274-001. There are 5 rubber feet that attach to the base enclosure in the locations illustrated below.
Removal and replacement procedures
4–6
Battery
Description
Spare part number
4-cell, 37-Wh Li-ion
493202-001
8-cell, 73-Wh Li-ion
501935-001
Before disassembling the computer, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch 1 to release the battery.
3. Remove the battery 2 from the computer.
Install the battery by inserting it into the battery bay until you hear a click.
Removal and replacement procedures
4–7
Hard drive
✎ The hard drive spare part kit includes a hard drive bracket.
Description
Spare part number
320-GB, 5400-rpm
493199-001
250-GB, 5400-rpm
493198-001
160-GB, 7200-rpm
513695-001
160-GB, 5400-rpm
493197-001
120-GB, 5400-rpm
493196-001
Before removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the hard drive:
1. Position the computer with the front toward you.
2. Loosen the four Phillips PM2.0×5.0 captive screws 1 that secure the hard drive cover to the computer.
3. Place your finger in the tab area 2 on the rear edge of the hard drive cover and lift it up and forward 3 to
remove the cover. The hard drive cover is included in the Plastics Kit, spare part number 493274-001.
Removal and replacement procedures
4–8
4. Loosen the Phillips PM2.5×10.0 captive screw 1 that secures the hard drive to the computer.
5. Grasp the Mylar tab 2 on the hard drive and slide the hard drive 3 away from the hard drive connector.
6. Remove the hard drive 4 from the hard drive bay.
7. If it is necessary to replace the hard drive bracket
a. Remove the two Phillips PM3.0×3.0 hard drive bracket screws 1 from each side of the hard drive.
b. Lift the bracket 2 straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
Removal and replacement procedures
4–9
Memory module
Description
Spare part number
2048-MB (PC2-5300, 667-MHz, DDR2)
493195-001
1024-MB (PC2-5300, 667-MHz, DDR2)
493194-001
Before removing the memory module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the memory module:
1. Position the computer with the front toward you.
2. Loosen the four Phillips PM2.0×5.0 captive screws 1 that secure the cover to the computer.
3. Place your finger in the tab area 2 on the rear edge of the hard drive cover and lift it up and forward 3 to
remove the cover. The memory module cover is included in the Plastics Kit, spare part number 493274-001.
Removal and replacement procedures
4–10
✎ The top memory module slot is for extension memory and the bottom slot is for primary memory.
4. Spread the retaining tabs 1 on each side of the memory module to release the memory module. (The edge of
the module opposite the slot rises away from the computer.)
5. Remove the memory module 2 by pulling the module away from the slot at an angle.
Memory modules are designed with a notch 3 to prevent incorrect insertion into the memory module slot.
✎
Reverse this procedure to install a memory module.
Removal and replacement procedures
4–11
WLAN module
Ä
CAUTION: The WLAN module and the WWAN module are not interchangeable.
Description
Spare part number
Broadcom 802.11a/b/g/n WLAN modules:
■ For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands,
and the United States
487330-001
■ For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei,
Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African
Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, the Congo,
Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,
Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland,
India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives,
Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia,
Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger,
Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia,
Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia
and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the
Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts &
Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
487330-002
(Continued)
Removal and replacement procedures
4–12
Description
Spare part number
Broadcom 802.11b/g WLAN modules:
■ For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands,
and the United States
459263-001
■ For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei,
Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African
Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, the Congo,
Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,
Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland,
India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives,
Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia,
Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger,
Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia,
Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia
and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the
Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts &
Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
459263-002
Intel 802.11a/b/g/n WLAN module:
■ For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands,
and the United States
480985-001
Intel 802.11a/b/g WLAN module:
■ For use in Pakistan, Russia, and Ukraine
Removal and replacement procedures
482957-001
4–13
Before removing the WLAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the WLAN module:
1. Position the computer with the front toward you.
2. Loosen the Phillips PM2.0×5.0 captive screw 1 that secures the WLAN module compartment cover to the
computer. The screw is identified by the wireless icon.
3. Lift the right side of the cover 2 and remove the cover.
Removal and replacement procedures
4–14
4. Disconnect the WLAN antenna cables 1 from the terminals on the WLAN module.
black WLAN antenna cable is connected to the WLAN module “Main” terminal. The white WLAN antenna
✎ The
cable is connected to the WLAN module “Aux” terminal.
5. Remove the two Phillips PM2.5×4.0 screws 2 that secure the WLAN module to the computer. (The edge of the
module opposite the slot rises away from the computer.)
6. Remove the WLAN module 3 by pulling the module away from the slot at an angle.
WLAN modules are designed with a notch 4 to prevent incorrect insertion.
✎
Reverse this procedure to install the WLAN module.
Removal and replacement procedures
4–15
Optical drive
✎ The optical drive spare part kit includes an optical drive bezel.
Description
Spare part number
DVD/CD-RW Combo Drive
493200-001
DVD-ROM Drive
493201-001
DVD±RW SuperMulti Double-Layer Drive with LightScribe
493961-001
Blu-ray ROM DVD±RW SuperMulti DL Drive
497536-001
Before removing the optical drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the optical drive:
1. Position the computer with the right side toward you.
2. Remove the Torx T8M2.5×6.0 slotted screw 1 that secures the optical drive to the computer.
3. Insert a flat-bladed screwdriver or similar tool into the optical drive tab access 2 and push the tab forward to
release the optical drive from the computer.
4. Remove the optical drive 3 from the computer.
Removal and replacement procedures
4–16
5. If it is necessary to replace the optical drive bracket:
a. Position the optical drive with the rear toward you.
b. Remove the two Phillips PM1.5×3.0 screws 1 that secure the optical drive bracket to the optical drive.
c. Remove the optical drive bracket 2.
Reverse this procedure to reassemble and install an optical drive.
Removal and replacement procedures
4–17
Keyboard
Description
Spare part number
For use in Belgium
493960-A41
For use in Canada
493960-121
For use in the Czech Republic
493690-221
For use in Denmark
493960-081
For use in France
493960-051
For use in Greece
493960-DJ1
For use in Germany
493960-041
For use in Hungary
493960-211
For use in Iceland
493960-DD1
For international use
493960-B31
For use in Italy
493960-061
For use in Israel
493960-BB1
For use in Japan
493960-291
For use in Latin America
493960-161
For use in Norway
493960-091
For use in Portugal
493960-131
For use in Russia
493960-251
For use in Saudi Arabia
493960-171
For use in Slovakia
493960-231
For use in Slovenia
493960-BA1
For use in Spain
493960-071
For use in Sweden and Finland
493960-B71
For use in Switzerland
493960-BG1
For use in South Korea
493960-AD1
For use in Taiwan
493960-AB1
For use in Thailand
493960-281
For use in Turkey
493960-141
For use in the United Kingdom
493960-031
For use in the United States
493960-001
Removal and replacement procedures
4–18
Before removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
Remove the keyboard:
1. Turn the computer upside down, with the front toward you.
2. Remove the three Torx T8M2.5×6.0 slotted screws that secure the keyboard to the computer.
Removal and replacement procedures
4–19
3. Turn the computer display-side up, and open the computer.
4. Lift the rear edge of the keyboard 1 and rotate the keyboard toward you 2 until it rests upside down on the top
cover.
5. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is attached, and disconnect the
keyboard cable 2 from the system board.
6. Remove the keyboard.
Reverse this procedure to install the keyboard.
Removal and replacement procedures
4–20
Top cover
Description
Spare part number
Top cover (includes caps lock light, capacitive board, fingerprint reader board and
cable, TouchPad, and TouchPad cable)
493278-001
Before removing the top cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
Remove the top cover:
1. Close the computer and turn it upside down, with the front toward you.
2. Remove the following:
Remove the four rubber screw covers on the front of the computer. Note that three of the screw covers are the
same 1 and one screw cover 2 is different. The rubber screw covers are included in the Plastics Kit, spare part
number 493274-001.
Removal and replacement procedures
4–21
3. Remove the ten Torx T8M2.5×6.0 slotted screws.
4. Remove the three Phillips PM2.0×2.0BH screws in the battery bay.
Removal and replacement procedures
4–22
5. Remove the three Phillips PM2.0×3.0 screws in the optical drive bay.
6. Turn the computer right-side up, with the front toward you.
7. Open the LED board cable ZIF connector 1, and then disconnect the cable.
8. Open the TouchPad cable ZIF connector 2, and then disconnect the cable.
9. Remove the two Torx T8M2.5×6.0 slotted screws 3 that attach the top cover to the base enclosure.
Removal and replacement procedures
4–23
10. Lift the rear edge and sides of the top cover 1 to release it. Move the top cover backward 2 and hold it.
11. Disconnect the fingerprint reader cable 1 and remove the top cover 2.
Reverse this procedure to install the top cover.
Removal and replacement procedures
4–24
Speaker assembly
Description
Spare part number
Speaker assembly
493273-001
Before removing the speaker assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
Remove the speaker assembly:
1. Disconnect the speaker assembly cable 1 from the system board.
2. Remove the Phillips PM3.0×4.0 screw 2 that attaches the left speaker to the base enclosure.
3. Remove the speaker cables from the clips on the system board, and then remove the speaker assembly 3 from
the base enclosure.
Reverse this procedure to install the speaker assembly.
Removal and replacement procedures
4–25
Display assembly
Description
Spare part number
12.1-inch, WXGA
493186-001
12.1-inch WXGA (with integrated webcam)
501932-001
12.1-inch, WXGA BrightView
493187-001
12.1-inch, WXGA BrightView (with integrated webcam)
501933-001
Before removing the display assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
g. Speaker assembly (see “Speaker assembly” on page 4-25)
Remove the display assembly:
1. Open the computer as far as possible.
2. Disconnect the display panel cable 1 from the system board.
3. Remove the WLAN antenna cable 2 from the opening in the base enclosure.
4. Disconnect the microphone cable 3 from the system board. Remove any tape that may be used to secure the
cable to the system board.
Removal and replacement procedures
4–26
Ä
CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can
result in damage to the display assembly and other computer components.
5. Remove the four Torx T8M2.5×6.0 slotted screws 1 that secure the display assembly to the computer.
6. Lift the display assembly 2 straight up and remove it.
Perform the following steps in sequence to remove or replace the display bezel or the display assembly internal
components.
1. If it is necessary to remove the display bezel:
a. Remove the six rubber screw covers in the display bezel.
b. Remove the six PM2.0×5.0 screws that secure the display bezel to the display enclosure.
Removal and replacement procedures
4–27
c. Lift the inside edge of the top side of the bezel 1 to disengage it from the clips, and then lift the left and
right sides 2 until the bezel disengages from the display enclosure.
d. Remove the display bezel 3. The display bezel is available using spare part number 495015-001.
Reverse this procedure to install the display bezel. Be careful to route the cables through the side openings in
the hinge covers and avoid pinching the cables between the bezel and display enclosure.
2. If it is necessary to remove the webcam module:
a. Disconnect the webcam cable 1 from the computer.
b. Remove the webcam module 2 from the display enclosure. (The webcam is secured with
double-sided tape.) The webcam can also be ordered separately and is available using spare part number
492159-001.
Removal and replacement procedures
4–28
3. If it is necessary to remove the display inverter:
a. Use a flat bladed screwdriver to release the inverter 1, which is secured with double-sided tape.
b. Disconnect the backlight cable 2 and the display panel cable 3 from the display inverter. The display
inverter is available using spare part number 493193-001.
4. If it is necessary to remove the display panel:
a. Remove the six Phillips PM2.0×5.0 screws 1 that secure the display panel to the display enclosure.
b. Remove the display panel 2 from the display enclosure.
Removal and replacement procedures
4–29
c. Remove the four Phillips PM1.5×3.0 screws 1 that secure the hinges to the display panel.
d. Remove the display hinges 2 from the display panel. The display hinges are available using spare part
number 493192-001.
5. If it is necessary to remove the microphone cable or WLAN transceivers and cable:
microphone, WLAN antenna cable, and the LCD module cable are included in the Cable Kit, spare part
✎ The
number 493275-001.
a. Remove the two Phillips PM2.0×6.0 screws 1 and display hinge covers 2.
Removal and replacement procedures
4–30
b. Remove the two microphone receivers 1 from the display enclosure, and then release the microphone cable
2 from the clips in the display enclosure.
Reverse this procedure to install the microphone.
c. Remove the adhesive tape from the WLAN transceivers 1, and then release the WLAN cables 2 from the
clips in the display enclosure.
Reverse this procedure to install the WLAN transceivers and cable.
Removal and replacement procedures
4–31
Audio board
Description
Spare part number
Audio board
493272-001
Before removing the audio board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
Remove the audio board and cable:
1. Open the audio board cable ZIF connector 1, and then remove the cable from the system board.
2. Remove the two Phillips PM2.0×3.0 screws 2 that secure the audio board to the system board.
3. Lift and move the audio board backward 3 so that the external audio connectors slide out of the openings in
the base enclosure.
Reverse this procedure to install the audio board.
Removal and replacement procedures
4–32
Fan
Description
Spare part number
Fan
493269-001
Before removing the fan, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
Remove the fan:
1. Disconnect the fan cable 1 from the system board.
2. Loosen the captive Phillips PM2.0×7.0 screw 2 that secures the fan to the base enclosure, and then remove the
fan 3 from the heat sink.
Reverse this procedure to install the fan.
✎ To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side of the computer.
The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to
turn on automatically when high temperature conditions exist. These conditions are affected by high external
temperatures, system power consumption, power management/battery conservation configurations, battery fast
charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side of
the computer.
Removal and replacement procedures
4–33
System board
Description
Spare part number
GM45 (includes RTC battery and replacement thermal material)
493185-001
GL40 (includes RTC battery and replacement thermal material)
504446-001
Before removing the system board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
g. Audio board (see “Audio board” on page 4-32)
h. Fan (see “Fan” on page 4-33)
When replacing the system board, be sure that the following additional components are removed from the defective
system board and installed on the replacement system board:
■
RTC battery (see “RTC battery” on page 4-36)
■
Modem module (see “Modem module” on page 4-37)
■
Bluetooth module (see “Bluetooth module” on page 4-39)
■
Heat sink (see “Heat sink” on page 4-41)
■
Processor (see “Processor” on page 4-43)
Removal and replacement procedures
4–34
Remove the system board:
1. Remove the Torx T8M2.5×6.0 slotted screw that secures the system board to the base enclosure. The screw is
located by the optical drive connector,
2. Flex the left side of the base enclosure until the USB, RJ-45, and RJ-11 jacks 1 clear the openings in the base
enclosure.
3. Use the optical drive connector 2 to lift the left side of the system board 3 until it rests at an angle.
4. Remove the system board from the base enclosure by pulling it away at an angle 4.
Reverse this procedure to install the system board.
Removal and replacement procedures
4–35
RTC battery
the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords and CMOS
✎ Removing
settings to be cleared.
Description
Spare part number
RTC battery
449137-001
Before removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
g. Audio board (see “Audio board” on page 4-32)
h. Fan (see “Fan” on page 4-33)
i. System board (see “System board” on page 4-34)
Remove the RTC battery:
1. Turn the system board upside down with the front toward you.
2. Lift the RTC battery from the socket.
Reverse this procedure to install the RTC battery.
Removal and replacement procedures
4–36
Modem module
modem module spare part kit does not include a modem module cable. The modem module cable is included
✎ The
in the Cable Kit, spare part number 493275-001. See “Cable Kit” on page 3-8 for more Cable Kit information.
Description
Spare part number
For use in Australia and New Zealand
461749-011
For use in all countries or regions except Australia and New Zealand
461749-001
Before removing the modem module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
g. Audio board (see “Audio board” on page 4-32)
h. Fan (see “Fan” on page 4-33)
i. System board (see “System board” on page 4-34)
j. Heat sink (see “Heat sink” on page 4-41)
Remove the modem module:
1. Turn the system board upside down with the rear edge toward you.
2. Remove the two Phillips PM2.0×3.0 screws 1 that secure the modem module to the system board.
3. Disconnect the modem module 2 from the system board by lifting it straight up.
4. Remove the modem module, cable, adhesive tape, and RJ-ll port.
Reverse this procedure to install the modem module and modem module cable.
Removal and replacement procedures
4–37
Bluetooth module
Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is
✎ The
included in the Cable Kit, spare part number 493275-001. See “Cable Kit” on page 3-8 for more Cable Kit
information.
Description
Spare part number
Bluetooth module
398393-002
Before removing the Bluetooth module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
g. Audio board (see “Audio board” on page 4-32)
h. Fan (see “Fan” on page 4-33)
i. System board (see “System board” on page 4-34)
Removal and replacement procedures
4–38
Remove the Bluetooth module:
1. Turn the system board upside down with the front toward you.
2. Disconnect the Bluetooth module cable 1 from the system board.
3. Remove the two Phillips PM1.5×3.0 screws 2 that secure the Bluetooth module to the system board.
4. Remove the module 3.
Reverse this procedure to install the Bluetooth module.
Removal and replacement procedures
4–39
Heat sink
Description
Spare part number
Thermal module (includes heat sink and thermal material)
493270-001
Before removing the heat sink, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
g. Audio board (see “Audio board” on page 4-32)
h. Fan (see “Fan” on page 4-33)
i. System board (see “System board” on page 4-34)
Remove the heat sink:
1. Loosen the four Phillips PM2.0×10.0 captive screws 1 that secure the heat sink to the system board.
2. Remove the heat sink 2 by lifting it straight up.
Removal and replacement procedures
4–40
thermal material must be thoroughly cleaned from the surfaces of the heat sink 1 and 3, the processor 2,
✎ The
and graphics subsystem component 4 on the system board each time the heat sink is removed. Thermal material
is included with all System Board, Heat Sink, and Processor Spare Part Kits.
Reverse this procedure to install the heat sink.
Removal and replacement procedures
4–41
Processor
✎ The processor spare part kit includes replacement thermal material.
Description
Spare part number
Intel Core2 Duo processors (6-MB L2 cache, 1066-MHz FSB):
■ T9600 2.8-GHz processor
486257-001
■ T9400 2.53-GHz processor
486256-001
■ P9500 2.53-GHz processor
496458-001
Intel Core2 Duo processors (3-MB L2 cache, 1066-MHz FSB):
■ P8700 2.53-GHz processor
512585-001
■ P8600 2.4-GHz processor
486255-001
■ P8400 2.26-GHz processor
486254-001
■ P7370 2.0-GHz processor (for use with Intel WLAN only)
507966-001
Intel Core Duo processors (2-MB L2 cache, 800-MHz FSB):
■ P5870 2.0-GHz processor (for use with no WLAN support or Intel WLAN only)
500771-001
■ P5670 1.8-GHz processor (for use with no WLAN support or Intel WLAN only)
500770-001
■ Intel Core Duo processors (1-MB L2 cache, 667-MHz FSB):
■ T3400 2.16-GHz processor
509061-001
■ T3200 2.0-GHz processor
509060-001
Intel Celeron-M processors (1-MB L2 cache, 667-MHz FSB):
■ 585 2.16-GHz processor
490337-001
■ 575 2.0-GHz processor
490336-001
Intel Celeron-T processors (1-MB L2 cache, 667-MHz FSB):
■ T1700 1.83-GHz processor
509059-001
■ T1600 1.66-GHz processor
509058-001
Removal and replacement procedures
4–42
Before removing the processor, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. WLAN module (see “WLAN module” on page 4-12)
d. Optical drive (see “Optical drive” on page 4-16)
e. Keyboard (see “Keyboard” on page 4-18)
f. Top cover (see “Top cover” on page 4-21)
g. Audio board (see “Audio board” on page 4-32)
h. Fan (see “Fan” on page 4-33)
i. System board (see “System board” on page 4-34)
j. Heat sink (see “Heat sink” on page 4-41)
Remove the processor:
1. Use a flat-bladed screwdriver to turn the processor locking screw 1 one-half turn counterclockwise until you
hear a click.
2. Lift the processor 2 straight up and remove it.
you install the processor, the gold triangle 3 on the processor must be aligned with the triangle 4
✎ When
embossed on the processor slot.
Reverse this procedure to install the processor.
Removal and replacement procedures
4–43
5
Computer Setup
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not
working or will not load.
✎ Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy
✎ An
support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System
Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
❏ To select a menu or a menu item, use the keyboard arrow keys and then press enter, or use a pointing device
to click the item.
❏ To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen.
❏ To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the
on-screen instructions.
can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and
✎ You
make selections in Computer Setup.
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
To exit Computer Setup menus, choose one of the following methods:
■ To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Ignore changes and exit, and then press enter.
■ To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter.
Your changes go into effect when the computer restarts.
Computer Setup
5–1
Restoring factory settings in Computer Setup
✎ Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the
on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter.
Your changes go into effect when the computer restarts.
✎ Your password settings and security settings are not changed when you restore the factory settings.
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
✎ Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
File menu
Select
To do this
System information
■ View identification information for the computer and the batteries in the
system.
■ View specification information for the processor, cache and memory size,
system ROM, video revision, and keyboard controller version.
Set System Date and Time
Set or change the date and time on the computer.
Restore defaults
Replace the configuration settings in Computer Setup with the original factory
settings. (Hard drive mode, password settings, and security settings are not
changed when you restore the factory settings.)
Ignore changes and exit
Cancel any changes entered during the current session. Then exit and restart
the computer.
Save changes and exit
Save any changes entered during the current session. Then exit and restart the
computer. Your changes go into effect when the computer restarts.
Computer Setup
5–2
Security menu
✎ Some of the menu items listed in this section may not be supported by your computer.
Select
To do this
Setup BIOS Administrator Password
Set up a BIOS administrator password.
User Management (requires a BIOS
administrator password)
■ Create a new BIOS user account.
■ View a list of ProtectTools users.
Password Policy (requires a BIOS
administrator password)
Revise password policy criteria.
HP SpareKey
Enable/disable HP SpareKey (enabled by default).
Always Prompt for HP SpareKey Enrollment
Enable/disable HP SpareKey enrollment (enabled by default).
Fingerprint Reset on Reboot (If Present)
Enable/disable the fingerprint reader (select models only; disabled by default).
Allow reset of HP ProtectTools security keys
Enable/disable reset of HP ProtectTools security keys
Change Password
Enter, change, or delete a BIOS administrator password.
HP SpareKey Enrollment
Enroll or reset HP SpareKey, which is a set of security questions and answers
used if you forget your password.
DriveLock Passwords
■ Enable/disable DriveLock on any computer hard drive (enabled by default).
■ Change a DriveLock user password or master password.
settings are accessible only when you enter Computer Setup
✎ DriveLock
by turning on (not restarting) the computer.
Automatic DriveLock
Enable/disable Automatic DriveLock support.
Disk Sanitizer
Run Disk Sanitizer to destroy all existing data on the primary hard drive or the
drive in the upgrade bay.
Ä
If you run Disk Sanitizer, the data on the selected drive is destroyed
permanently.
System IDs
Enter a user-defined computer asset tracking number and ownership tag.
Always Prompt for HP SpareKey Enrollment
Enable/disable a prompt for HP SpareKey enrollment.
Diagnostics menu
Select
To do this
System Diagnostics menu
■ F1 System Information—Displays the following information:
❐ Identification information for the computer and the batteries in the system.
❐ Specification information for the processor, cache and memory size,
system ROM, video revision, and keyboard controller version.
■ F2 Start-up Test—Verifies the system components needed for starting
the computer.
■ F3 Run-In Test—Runs a comprehensive check on system memory.
■ F4 Hard Disk Test—Runs a comprehensive self-test on any hard drive in
the system.
Computer Setup
5–3
System Configuration menu
✎ Some of the listed System Configuration options in this section may not be supported by your computer.
Select
To do this
Language
Change the Computer Setup language.
Boot Options
■
■
■
■
■
■
■
■
■
Device Configurations
■ Enable/disable USB legacy support (enabled by default). When enabled,
USB legacy support allows the following:
❐ Use of a USB keyboard in Computer Setup even when a Windows®
operating system is not running.
❐ Startup from bootable USB devices, including a hard drive, diskette drive,
or optical drive connected by a USB port to the computer.
■ Select a parallel port mode: ECP (Enhanced Capabilities Port), standard,
bidirectional, or EPP (Enhanced Parallel Port).
■ Enable/disable fan always on while connected to an AC outlet (enabled
by default).
■ Enable/disable LAN Power Save (select models only). When enabled, saves
power by turning off the LAN when not in use (enabled by default).
Set a Startup Menu delay (in seconds).
Enable/disable Custom Logo (disabled by default).
Enable/disable Display Diagnostic URL (enabled by default).
Enable/disable CD-ROM boot (enabled by default).
Enable/disable SD Card boot (enabled by default).
Enable/disable floppy boot (enabled by default).
Enable/disable PXE Internal NIC boot (enabled by default).
Set the Express Boot Popup delay in seconds.
Set the boot order.
■ Enable/disable Data Execution Prevention. When enabled, the processor can
disable some virus code execution, which helps to improve computer security.
■ SATA (Serial Advanced Technology Attachment) device mode. The following
options are available:
❐ AHCI (Advanced Host Controller Interface)
❐ IDE (Integrated Drive Electronics)
❐ RAID (select models only)
✎ Availability of the options above varies by computer model.
■ Enable/disable secondary battery fast charge (enabled by default).
■ Enable/disable HP QuickLook 2 (enabled by default).
■ Enable/disable Virtualization Technology (select models only; disabled
by default).
■ Enable/disable TXT (Intel® Trusted Execution Technology) (select models
only; disabled by default).
■ Enable/disable Dual Core CPU (select models only; enabled by default).
■ Enable/Disable Unified Extensible Firmware Interface (UEFI) mode (disabled
by default).
(Continued)
Computer Setup
5–4
Select
To do this
Built-In Device Options
■ Enable/disable the wireless button state (enabled by default).
■ Enable/disable embedded WWAN device radio (select models only; enabled
by default).
■ Enable/disable embedded Bluetooth® device radio (enabled by default).
■ Enable/disable the Network Interface Controller (LAN) (enabled by default).
■ Set the wake on LAN state. Options include the following:
❐ Disabled
❐ Boot to Network (set by default)
❐ Follow Boot Order
■ Enable/disable the fingerprint device (enabled by default).
■ Enable/disable a modem device (enabled by default).
■ Enable/disable the embedded WLAN device (enabled by default).
■ Enable/disable LAN/WLAN switching (disabled by default).
■ Enable the ambient light sensor (enabled by default).
■ Enable/disable the Notebook Multibay device (enabled by default).
■ Enable/disable the integrated camera (select models only; enabled
by default).
Port Options (all are enabled by default)
✎ All port options are enabled by default.
■
■
■
■
■
■
Enable/disable the Smart Card slot.
Enable/disable the ExpressCard slot.
Enable/disable the serial port.
Enable/disable the parallel port.
Enable/disable the flash media reader.
Enable/disable the USB port.
Ä
Disabling the USB port also disables MultiBay devices and ExpressCard
devices on the advanced port replicator.
■ Enable/disable the 1394 port.
Set Security Level
Change, view, or hide security levels for all BIOS menu items.
Restore Security Defaults
Restore the default security settings.
Computer Setup
5–5
6
Specifications
Computer specifications
Metric
U.S.
Length
22.6 cm
8.9 in
Width
29.4 cm
11.7 in
Height (front to rear)
2.8 to 3.6 cm
1.10 to 1.42 in
1.85 kg
4.07 lbs
Dimensions
Weight
Equipped with 4-cell battery and optical drive
Input power
Operating voltage
19.0 V dc @ 4.74 A - 65 W
Operating current
4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Operating
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Nonoperating
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
✎ range
of temperatures.
Specifications
6–1
12.1-inch, WXGA display specifications
Metric
U.S.
Height
16.9 cm
6.7 in
Width
26.2 cm
10.3 in
Diagonal
30.8 cm
12.1 in
Number of colors
Up to 16.8 million
Contrast ratio
250:1 (typical)
Brightness
180 nits (typical)
Dimensions
Pixel resolution
Pitch
0.279 × 0.279 mm
Format
1280 × 800
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4.0 W
Viewing angle
+/-40° horizontal, +120/-40° vertical (typical)
Hard drive specifications
320-GB*
250-GB*
160-GB*
120-GB*
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
Weight
101 g
101 g
101 g
101 g
Interface type
SATA
SATA
SATA
SATA
Transfer rate
100 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
ATA security
Single track
3 ms
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
24 ms
Logical blocks
625,142,448
488,397,168
312,581,808
234,441,648
Disc rotational speed
5400 rpm
5400 rpm
5400 rpm
5400 rpm
Operating temperature
5°C to 55°C (41°F to 131°F)
Dimensions
Seek times (typical read, including setting)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
✎ Certain restrictions and exclusions apply. Contact technical support for details.
Specifications
6–2
DVD/CD-RW Combo Drive specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI,
CD-TEXT, CD-ROM, CD-ROM
XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video
CD), Multisession CD
(Photo-CD, CD-EXTRA,
Portfolio, CD-R, CD-RW),
CD-R, CD-RW, DVD-ROM
(DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
Access time
CD
DVD
Random
< 190 ms
< 180 ms
Cache buffer
2 MB
Data transfer rate
16X CD-ROM
2,400 KB/sec
8X DVD
2,400 KB/sec
16X CD-R
2,400 KB/sec
16X CD-RW
2,400 KB/sec
Transfer mode
Multiword DMA mode 2
Blu-ray ROM DVD±RW SuperMulti DL Drive specifications
Applicable disc
Read:
Write:
BD-ROM, BD-ROM-DL, BD-R,
BD-R-DL, BD-RE, BD-RE-DL,
DVD-ROM, DVD+R,
DVD+R-DL, DVD+RW, DVD-R,
DVD-R-DL, DVD-RW,
DVD-RAM (Ver.2), CD-DA,
CD-ROM (Mode 1 and
mode 2), CD-ROM XA
(Mode 2, form 1 and form 2),
Photo CD (Single and multiple
sessions), CD Extra, CD-R,
CD-RW, and CD-TEXT
DVD-RAM (Ver.2), DVD+R,
DVD-R, CD-R, and CD-RW
Access time
BD
DVD
Random
< 230 ms
< 180 ms
Cache buffer
4.5 MB
Data transfer rate
2X BD-RAM
9 MB/sec
8X DVD
2,400 KB/sec
16X CD-R
2,400 KB/sec
16X CD-RW
2,400 KB/sec
Specifications
6–3
DVD±RW SuperMulti Double-Layer Drive specifications
Applicable disc
Read:
Write:
CD-ROM, CD-R, CD-RW, High
Speed CD-RW, Ultra & Ultra+
Speed CD-RW, DVD,
DVD±R/RW, DVD±R,
DVD-RAM
DVD-RAM (Ver.2), DVD±R,
DVD±RW, DVD±Dual, CD-R,
and CD-RW
Access time
CD
DVD
Random
< 130 ms
< 150 ms
Cache buffer
2 MB
Data transfer rate
5X DVD-RAM
6,750 KB/sec
8X DVD±RW
10,800 KB/sec
8X DVD±R
10,800 KB/sec
16X CD-R
3,600 KB/sec
16X CD-RW (High Speed)
1,500 KB/sec
DVD-ROM Drive
Applicable disc
DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18, CD-ROM (Mode 1
and 2), CD Digital
Audio, CD-XA ready (Mode 2, Form 1 and Form 2), CD-I
(Mode 2, Form 1 and Form 2), CD-R, CD-RW, Photo CD (single
and multisession), CD-Bridge
Access time
CD
DVD
Random
< 100 ms
< 125 ms
Full stroke
< 175 ms
< 225 ms
Cache buffer
512 KB
Data transfer rate
CD-R (24X)
3600 KB/s (150 KB/s at 1X CD rate)
CD-RW (10X)
1500 KB/s (150 KB/s at 1X CD rate)
CD-ROM (24X)
3600 KB/s (150 KB/s at 1X CD rate)
DVD (8X)
10,800 KB/s (1,352 KB/s at 1X DVD rate)
Multiword DMA mode 2
16.6 MB/s
Specifications
6–4
System DMA specifications
Hardware
DMA System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Not applicable
DMA6
Not assigned
DMA7
Not assigned
*PC Card controller can use DMA 1, 2, or 5.
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ8
System CMOS/real-time clock
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ16
Intel ICH9 Family USB universal Host Controller 2937
Mobile Intel 4 Series Express Chipset Family
IRQ17
High Definition Audio Controller
Intel ICH9 Family USB universal Host Controller 2938
Marvell Yukon 88E8072 PCIE-Gigabit Ethernet Controller
IRQ18
Intel ICH9 Family USB universal Host Controller 2939
Intel ICH9 Family USB universal Host Controller 2936
IRQ19
Intel ICH9 Family USB2 Enhanced Controller 293C
IRQ20
Intel ICH9 Family USB2 Enhanced Controller 293A
Intel ICH9 Family USB universal Host Controller 2934
IRQ21
Intel ICH9M-E/M SATA AHCI Controller
IRQ22
Intel ICH9 Family USB universal Host Controller 2935
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
Cards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port
✎ PC
may assert IRQ3 or IRQ4.
✎ For operating systems after Windows 2000, APIC (advanced programming interrupt controller) is used.
Specifications
6–5
System I/O address specifications
I/O address (hex)
System function (shipping configuration)
000 - 01F
DMA controller
020 - 021
Program interrupt controller
024 - 025
Program interrupt controller
028 - 029
Program interrupt controller
02C - 03D
Program interrupt controller
02E - 02F
Motherboard resource
030 - 031
Program interrupt controller
034 - 035
Program interrupt controller
038 - 039
Program interrupt controller
03C- 03D
Program interrupt controller
040 - 043
System timer
04E-04F
Motherboard resource
050-053
System timer
060
Standard 101-/102-key or Microsoft Natural Keyboard
061
Motherboard resource
062
Microsoft ACPI-Compliant Embedded Controller
063
Motherboard resource
064
Standard 101-/102-key or Microsoft Natural Keyboard
065
Motherboard resources
066
Microsoft ACPI-Compliant Embedded Controller
067
Motherboard resources
070
Motherboard resources
071-077
System CMOS/real time clock
080
Motherboard resources
081-091
Direct memory access controller
092
Motherboard resources
093-09F
Direct memory access controller
0A0-0A1
Program interrupt controller
0A4-0A5
Program interrupt controller
0A8-0A9
Program interrupt controller
0AC-0AD
Program interrupt controller
0B0-0B1
Program interrupt controller
0B2-0B3
Motherboard resources
0B4- 0B5
Program interrupt controller
0B8-0B9
Program interrupt controller
0BC- 0BD
Program interrupt controller
(Continued)
Specifications
6–6
I/O address (hex)
System function (shipping configuration)
0C0- 0DF
Direct memory access controller
0F0- 0F0
Numeric data processor
0200-027F
Motherboard resource
3B0-3BB
Mobile Intel® 4 Series Express Chipset Family
3C0-3DF
Mobile Intel® 4 Series Express Chipset Family
400-47F
Motherboard resource
4D0-4D1
Programmable interrupt controller
500-57F
Motherboard resources
1000-1003
Motherboard resources
1010-101F
Motherboard resources
2000-20FF
Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller
2000-2FFF
ICH9 Family PCI Express Root Port6-294A
3000-4FFF
ICH9 Family PCI Express Root Port5-2948
5000-6FFF
ICH9 Family PCI Express Root Port3-2944
7000-701F
ICH9M-E/M SATA AHCI Controller
7020-703F
ICH9 Family USB Universal Host Controller-2936
7040-705F
ICH9 Family USB Universal Host Controller-2935
7060-707F
ICH9 Family USB Universal Host Controller-2934
7080-709F
ICH9 Family USB Universal Host Controller-2939
70A0-70BF
ICH9 Family USB Universal Host Controller-2938
70C0-70DF
ICH9 Family USB Universal Host Controller-2937
70E0-70E7
ICH9M-E/M SATA AHCI Controller
70E8-70EF
ICH9M-E/M SATA AHCI Controller
70F0-70F7
Mobile Intel(R) 4 Series Express Chipset Family
70F8-70FB
ICH9M-E/M SATA AHCI Controller
70FC-70FF
ICH9M-E/M SATA AHCI Controller
EF80-EF9F
Motherboard resources
FE00-FE0F
Motherboard resources
FE80-EF8F
Motherboard resources
FFFF
Motherboard resources
Specifications
6–7
System memory map specifications
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
64 KB
000C0000-000CFFFF
Video BIOS
64 KB
000E8000-000FFFFF
System BIOS
00100000- XFFFFFFF
Extended memory (based on memory
installed)
(X+1)0000000-FEDFFFFF
PCI bus
FED00000-FED003FF
High precision event timer
FEE01000-FFFFFFFF
PCI bus
Specifications
6–8
7
Screw listing
This section provides specification and reference information for the screws used in the computer. Some screws
listed in this section are available in the Screw Kit, spare part number 493277-001.
Phillips PM1.5×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
8
3.0 mm
1.5 mm
3.0 mm
Where used: 2 screws that secure the optical drive bracket to the optical drive
Screw listing
7–1
Where used: 4 screws that secure the display hinges to the display panel
Where used: 2 screws that secure the Bluetooth module to the system board
Screw listing
7–2
Phillips PM2.0×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
2
3.0 mm
2.0 mm
3.0 mm
Where used: 2 screws that secure the audio board to the base enclosure
Screw listing
7–3
Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
2
4.0 mm
2.0
3.5 mm
Where used: 2 screws that secure the WLAN module to the system board
Screw listing
7–4
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
5
5.0 mm
2.0 mm
3.5 mm
Where used: 4 captive screws 1 that secure the hard drive cover to the computer and 1 captive screw 2 that
secures the wireless module compartment cover to the computer
Screw listing
7–5
Phillips PM2.0×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
5
3.0 mm
2.0 mm
4.0 mm
Where used: 3 screws (in optical drive bay) that secure the top cover to the computer
Where used: 2 screws that secure the modem module to the system board
Screw listing
7–6
Phillips PM2.0×6.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
2
6.0 mm
2.0 mm
4.0 mm
Where used: 2 screws that secure the display hinge covers to the display enclosure
Screw listing
7–7
Phillips PM2.0×5.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
12
5.0 mm
2.0 mm
4.0 mm
Where used: 6 screws that secure the display panel to the display enclosure
Where used: 6 screws that secure the display bezel to the display enclosure
Screw listing
7–8
Phillips PM2.0×7.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
7.0 mm
2.0 mm
4.0 mm
Where used: 1 captive screw that secures the fan to the base enclosure
Screw listing
7–9
Phillips PM2.0×10.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
10.0 mm
2.0
5.0 mm
Where used: 4 captive screws that secure the heat sink to the system board
Screw listing
7–10
Phillips PM2.5×10.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
1
10.0 mm
2.5
5.0 mm
Where used: 1 captive screw that secures the hard drive to the computer
Screw listing
7–11
Phillips PM3.0×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
3.0 mm
3.0
4.5 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
Screw listing
7–12
Phillips PM3.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
4.0 mm
3.0
4.5 mm
Where used: 1 screw that secures the speaker assembly to the base enclosure
Screw listing
7–13
Phillips T2.0×2.0BH screw
Color
Quantity
Length
Thread
Head diameter
Black
3
2.0 mm
2.0
6.0 mm
Where used: 3 screws (in the battery bay) that secure the top cover to the base enclosure
Screw listing
7–14
Torx T8M2.5×6.0 slotted screw
Color
Quantity
Length
Thread
Head diameter
Black
21
6.0 mm
2.5 mm
4.0 mm
Where used: 1 screw that secures the optical drive to the computer
Where used: 3 screws that secure the keyboard to the computer
Screw listing
7–15
Where used: 2 screws that secure the top cover to the base enclosure (top)
Where used: 4 screws that secure the display assembly hinges to the computer
Screw listing
7–16
Where used: 1 screw that secures the system board to the base enclosure
Where used: 10 screws that secure the top cover to the base enclosure
Screw listing
7–17
8
Backup and recovery
Backup and recovery in Windows Vista
To protect your information, use the Backup and Restore Center to back up individual files and folders, back up
your entire hard drive (select models only), or create system restore points. In case of system failure, you can use
the backup files to restore the contents of your computer.
Windows Vista® provides the following advanced backup and recovery options:
■
Backing up individual files and folders
■
Backing up the entire hard drive (select models only)
■
Scheduling automatic backups (select models only)
■
Creating system restore points
■
Recovering individual files
■
Restoring the computer to a previous state
■
Recovering information using recovery tools
✎ For detailed instructions, perform a search for these topics in Help and Support.
Backup tips
■
Connect the computer to AC power during the backup process.
■
Store personal files in the Documents folder and back them up regularly.
■
Back up templates that are stored in their associated programs.
■
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
1. Display the screen you want to save.
2. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4. Save the document.
Backup and recovery
8–1
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your initial backup
immediately after software setup. As you add new software and data files, you should continue to back up your
system on a regular basis to maintain a reasonably current backup.
To create a backup using Backup and Restore Center, follow these steps:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Follow the on-screen instructions to back up your entire computer (select models only) or your files.
includes the User Account Control feature to improve the security of your computer. You may be
✎ Windows
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
Performing a recovery
In case of system failure, use the f11 recovery tool to recover your original hard drive image. The image includes
the Windows operating system and software programs installed at the factory.
Vista provides additional recovery tools through the operating system. For additional information, go
✎ Windows
to Help and Support.
you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system DVD to
✎ Ifreboot
the computer and repair the operating system. For additional information, refer to the “Recovering
information using a Windows Vista operating system DVD (purchased separately)” section in this guide.
Recovering the hard drive using f11
Ä
CAUTION: Using f11 will completely erase hard drive contents and reformat the hard drive. All files you have created and any
software installed on the computer will be permanently removed. The f11 recovery tool reinstalls the operating system and HP
programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled.
To recover the original hard drive image, follow these steps:
1. If possible, back up all personal files.
2. If possible, check for the presence of the HP Recovery partition. To find the partition, select Start >
Computer.
the HP Recovery partition has been deleted, you will need to recover your operating system and
✎ Ifprograms
using the Windows Vista operating system DVD and the Driver Recovery disc (purchased
separately). For additional information, refer to the “Recovering information using a Windows Vista
operating system DVD (purchased separately)” section in this guide.
3. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message
is displayed at the bottom of the screen.
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Backup and recovery
8–2
Recovering information using a Windows Vista operating system DVD (purchased separately)
If you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system DVD to
reboot the computer and repair the operating system. Make sure that your most recent backup (stored on discs or on
an external drive) is easily accessible. To order a Windows Vista operating system DVD, go to
http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the
DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet
included with the computer.
Ä
CAUTION: Using a Windows Vista operating system DVD will completely erase hard drive contents and reformat the hard
drive. All files you have created and any software installed on the computer will be permanently removed. When reformatting is
complete, the recovery process will help you restore the operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows Vista operating system DVD, follow these steps:
✎ This process will take several minutes.
1. If possible, back up all personal files.
2. Restart the computer, and then insert the Windows Vista operating system DVD into the optical drive before
the Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your computer.
7. Follow the on-screen instructions.
Backup and recovery
8–3
Backup and recovery in Windows XP
To protect your information, use the Windows® Backup utility (select models only) to back up files and folders or
create recovery points. In case of system failure, you can use the backup files to restore your computer.
Windows provides the following options:
■
Backing up individual files and folders
■
Backing up all files and folders
■
Scheduling automatic backups
■
Creating recovery points
■
Recovering information
✎ For detailed instructions, perform a search for these topics in Help and Support.
✎ In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your initial backup
immediately after software setup. As you add new software and data files, you should continue to back up your
system on a regular basis to maintain a reasonably current backup.
You can back up individual files or folders to an optional external hard drive or to a network drive.
Note the following when backing up:
■
Store personal files in the My Documents folder, and back it up periodically.
■
Back up templates stored in their associated programs.
■
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time-saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
1. Display the screen you want to save.
2. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, click Edit > Paste.
The screen image is added to the document.
4. Save the document.
Backup and recovery
8–4
To create a backup using the Windows Backup utility (select models only), follow these steps:
✎ Be sure that the computer is connected to AC power before you start the backup process.
✎ The backup process may take over an hour, depending on file size and the speed of the computer.
1. Click Start > All Programs > Accessories > System Tools > Backup.
2. Follow the on-screen instructions.
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
■
Windows recovery tools (select models only): You can use the Windows Backup utility to recover information
you have previously backed up.
■
Operating System and Driver Recovery discs (included with your computer): You can use the discs to recover
your operating system and programs installed at the factory.
Recovering your information
To recover information you previously backed up, follow these steps:
1. If possible, back up all personal files.
2. Click Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard opens.
3. Click Restore files and settings, and then click Next.
4. Follow the on-screen instructions.
additional information on initiating a recovery in Windows, perform a search for this topic in Help and
✎ For
Support.
Recovering the operating system and programs
Ä
CAUTION: The recovery process reformats and completely erases the hard drive. All files you have created and any software
installed on the computer are permanently removed. The recovery process reinstalls the original operating system, software, and
drivers. Software, drivers, and updates not installed by HP must be manually reinstalled.
To recover your operating system and programs, follow these steps:
1. If possible, back up all personal files.
2. Insert the Operating System disc into the optical drive.
3. Shut down the computer.
4. Turn on the computer.
5. Follow the on-screen instructions to install the operating system.
6. After the operating system is installed, remove the Operating System disc and insert the Driver
Recovery disc.
7. Follow the on-screen instructions to install the drivers and programs.
Backup and recovery
8–5
9
Connector pin assignments
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Connector pin assignments
9–1
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
Connector pin assignments
9–2
HDMI
Pin
Signal
1
Transition minimized differential signal (TDMS) data 2+
2
Transition minimized differential signal (TDMS) data 2 shield
3
Transition minimized differential signal (TDMS) data 2-
4
Transition minimized differential signal (TDMS) data 1+
5
Transition minimized differential signal (TDMS) data 1 shield
6
Transition minimized differential signal (TDMS) data 1 shield
7
Transition minimized differential signal (TDMS) data 0+
8
Transition minimized differential signal (TDMS) data 0 shield
9
Transition minimized differential signal (TDMS) data 0-
10
Transition minimized differential signal (TDMS) clock +
11
Transition minimized differential signal (TDMS) data clock shield
12
Transition minimized differential signal (TDMS) data clock-
13
Consumer electronics control (CEC)
14
Not connected
15
Display data channel (DDC) clock
16
Display data channel (DDC) data
17
Ground
18
+5V Power
19
Hot plug detect
Connector pin assignments
9–3
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
Connector pin assignments
9–4
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
Connector pin assignments
9–5
10
Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC
or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or region
where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region where
the computer is used.
Requirements for all countries and regions
The requirements listed below are applicable to all countries and regions:
■
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
■
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the
country or region where the power cord set will be used.
■
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or
250 V AC, as required by the power system of each country or region.
■
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13
connector for mating with the appliance inlet on the back of the computer.
Power cord set requirements
10–1
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
The Netherlands
KEMA
1
Norway
NEMKO
1
The People’s Republic of China
CCC
5
South Korea
EK
4
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese
Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
Power cord set requirements
10–2
11
Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household waste.
Follow the local laws and regulations in your area for computer battery disposal.
Display
Å
WARNING: The backlight contains mercury. Caution must be exercised when removing and handling the backlight to avoid
damaging this component and causing exposure to the mercury.
Ä
CAUTION: The procedures in this chapter can result in damage to display components. The only components intended for
recycling purposes are the liquid crystal display (LCD) panel and the backlight. When you remove these components, handle
them carefully.
disposal. This HP product contains mercury in the backlight in the display assembly that might
✎ Materials
require special handling at end-of-life. Disposal of mercury may be regulated because of environmental
considerations. For disposal or recycling information, contact your local authorities, or see the Electronic
Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight 1 and the liquid crystal display (LCD) panel 2.
procedures provided in this chapter are general disassembly instructions. Specific details, such as screw
✎ The
sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.
Recycling
11–1
Perform the following steps to disassemble the display assembly:
1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel
until the bezel disengages from the display assembly.
3. Remove the display bezel 3.
Recycling
11–2
4. Disconnect all display panel cables 1 from the display inverter and remove the inverter 2.
5. Remove all screws 1 that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly 2 from the display enclosure.
7. Turn the display panel assembly upside down.
8. Remove all screws that secure the display panel frame to the display panel.
Recycling
11–3
9. Use a sharp-edged tool to cut the tape 1 that secures the sides of the display panel to the display panel frame.
10. Remove the display panel frame 2 from the display panel.
11. Remove the screws 1 that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover 2 and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
15. Remove the backlight cables 1 from the clip 2 in the display panel.
Recycling
11–4
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
Å
WARNING: The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging
this component and causing exposure to the mercury.
18. Remove the backlight from the backlight frame.
Recycling
11–5
19. Disconnect the display cable 1 from the LCD panel.
20. Remove the screws 2 that secure the LCD panel to the display rear panel.
21. Release the LCD panel 3 from the display rear panel.
22. Release the tape 4 that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
Recycling
11–6
Index
A
AC adapter, spare part number 3–11
AHCI (Advanced Host Controller Interface) 5–4
antennae
disconnecting 4–15
location 2–1
product description 1–3
spare part number 3–3
audio, product description 1–3
audio-in jack
location 2–7
pin assignments 9–1
audio-out jack
location 2–7
pin assignments 9–1
B
backing up files 8–2
backing up files and folders 8–4
Backup and Restore Center 8–1, 8–2
Backup tips 8–1
base enclosure, spare part number 3–5
battery bay 2–9
battery light 2–6, 2–7
battery, spare part number 3–5, 3–14
BIOS administrator password 5–3
Bluetooth module
removal 4–38
spare part number 3–4, 3–12, 4–38
Bluetooth module cable, illustrated 3–8
Blu-ray ROM DVD+/-RW SuperMulti DL Drive
removal 4–16
spare part number 3–5
specifications 6–3
Boot 5–4
Boot Options 5–4
boot order 5–4
Built-In Device Options 5–5
built-in devices
ambient light sensor 5–5
Bluetooth radio 5–5
embedded WLAN 5–5
fingerprint reader 5–5
integrated camera 5–5
Index
LAN/WLAN switching 5–5
modem 5–5
Network Interface Controller (LAN) 5–5
notebook Multibay device 5–5
wake on LAN 5–5
wireless button 5–5
WWAN radio 5–5
buttons
info 2–3
power 2–3
TouchPad 2–2
volume 2–4
wireless 2–4
C
Cable Kit
contents 3–8
spare part number 3–7
chipset, product description 1–1
CMOS clearing 4–4
components
bottom 2–9
buttons 2–3
display 2–1
fingerprint reader 2–3
front 2–7
keys 2–5
left-side 2–7
lights 2–6
right-side 2–8
top 2–2
computer feet, spare part number 3–5, 3–14
Computer Setup
Diagnostics menu 5–3
File menu 5–2
navigating and selecting 5–1
restoring factory settings 5–2
Security menu 5–3
start 5–1
System Configuration menu 5–4
computer specifications 6–1
connectors, power 2–6, 2–7
creating a backup 8–2
creating recovery points 8–1, 8–4
Index–1
D
F
Device Configurations 5–4
Diagnostics menu 5–3
Disk Sanitizer 5–3
diskette drive
precautions 4–2
product description 1–2
display assembly
product description 3–3
spare part number 3–3, 3–13
display bezel
removal 4–27
screws 7–8
spare part number 3–3
Display Cable Kit, spare part number 3–3
display component recycling 11–1
display hinge cover
removal 4–30
spare part number 3–3
display hinge, spare part number 3–3
display inverter
removal 4–29
spare part number 3–3, 3–14
drive light 2–7
DriveLock Automatic 5–3
DriveLock Passwords 5–3
Driver recovery 8–5
Driver Recovery discs 8–5
drives, boot order 5–4
Dual Core CPU 5–4
DVD+/-RW SuperMulti Double-Layer Drive
removal 4–16
spare part number 3–5
specifications 6–4
DVD/CD-RW Combo Drive
removal 4–16
spare part number 3–5, 3–14
specifications 6–3
DVD-ROM Drive
removal 4–16
spare part number 1–2, 3–5
specifications 6–4
f11 recovery 8–2
fan
removal 4–33
spare part number 3–4
feet 3–14
File menu 5–2
files and folders, recovering 8–4
fingerprint 5–5
fingerprint reader, location 2–4
fn key 2–5
function keys 2–5
E
electrostatic discharge 4–2
esc key 2–5
Ethernet, product description 1–3
Execution Disable 5–4
ExpressCard slot 2–8
external monitor port
location 2–8
pin assignments 9–2
Index
G
graphics subsystem, product description 1–2
grounding guidelines 4–2
H
Hard Disk Test 5–3
hard drive
location 2–9
product description 1–2
removal 4–8
restoring factory defaults 5–2
spare part number 3–7, 4–8
specifications 6–2
hard drive compartment cover
illustrated 3–9
spare part number 3–4
heat sink
removal 4–40
spare part number 3–5, 3–14, 4–40
hinge, spare part number 3–3, 3–14
HP QuickLook 2 5–4
HP SpareKey enrollment 5–3
I
I/O address specifications 6–6
IDE (Integrated Drive Electronics) 5–4
info button 2–3
interrupt specifications 6–5
inverter
removal 11–3
spare part number 3–3, 3–14
J
jacks
audio-in 2–7
audio-out 2–7
headphone 2–7
microphone 2–7
RJ-11 2–7
RJ-45 2–7
Index–2
K
keyboard
product description 1–3
removal 4–19
spare part number 3–3, 3–14
keypad keys 2–5
keys
esc 2–5
fn 2–5
function 2–5
Windows applications key 2–5
Windows logo key 2–5
L
LAN Power Save 5–4
language, changing in Computer Setup 5–4
left-side components 2–7
legacy support, Universal Serial Bus (USB) 5–1, 5–4
lights
battery 2–6
caps lock 2–6
drive 2–7
power 2–6
volume down 2–6
volume mute 2–6
volume up 2–6
webcam 2–1
wireless 2–6
M
mass storage devices
illustrated 3–10
spare part numbers 3–10
media card, external 1–3
memory map specifications 6–8
memory module
product description 1–2
removal 4–10
spare part number 3–7, 3–14
memory module compartment cover removal 4–10
microphone 3–14
location 2–1
product description 1–3
removal 4–30
spare part number 3–3, 3–14
microphone jack
location 2–7
pin assignments 9–1
Miscellaneous Display Kit, spare part number 3–3
model name 3–1
model number 3–1
modem module
product description 1–3
removal 4–37
Index
spare part number 3–4, 3–12
modem module cable, illustrated 3–4, 3–8
monitor port
location 2–8
pin assignments 9–2
N
navigating in Computer Setup 5–1
network jack
location 2–7
pin assignments 9–4
numeric keypad 2–5
O
Operating System and Driver Recovery discs 8–5
operating systems 8–5
optical drive
location 2–7
product description 1–2
spare part number 3–5, 3–10
Optical Drive Kit 3–5
P
packaging and transporting guidelines 4–3
parallel port mode 5–4
password clearing 4–4, 4–36
passwords 5–3
pin assignments
audio-in 9–1
audio-out 9–1
HDMI 9–3
headphone 9–1
microphone 9–1
modem 9–4
monitor port 9–2
network 9–4
RJ-11 9–4
RJ-45 9–4
Universal Serial Bus (USB) port 9–4
plastic parts 4–1
Plastics Kit
contents 3–9
spare part number 3–4, 3–9, 3–14
pointing device components
TouchPad 2–2
TouchPad buttons 2–2
TouchPad scroll zone 2–2
pointing devices
illustrated 2–2
product description 1–3
port options
ExpressCard slot 5–5
flash media reader 5–5
Smart Card slot 5–5
Index–3
ports
1394 port 5–5
parallel port 5–5
serial port 5–5
USB port 5–5
power button 2–3
power connector 2–7
power cord
set requirements 10–1
spare part number 3–13
power light 2–6
power requirements, product description 1–4
processor
product description 3–5, 4–42
removal 4–42
spare part number 3–5, 3–12, 3–13, 4–42
product description
audio 1–3
chipset 1–1
diskette drive 1–2
display panel 1–2
docking 1–3
Ethernet 1–3
external media card 1–3
hard drives 1–2
keyboard 1–3
memory 1–2
microphone 1–3
modem 1–3
operating system 1–4
optical drives 1–2
pointing devices 1–3
ports 1–3
power requirements 1–4
processors 1–1
security 1–4
serviceability 1–4
wireless 1–3
product name 1–1, 3–1
R
RAID (Redundant Array of Independent Disks) devices
5–4
recovering information 8–2, 8–5
recovering the hard drive 8–2
recovery disc
using 8–2
Windows Vista 8–3
Windows XP 8–5
recovery options 8–1
recovery partition 8–2
recovery points 8–4
recovery, using f11 8–2
Index
recycling
battery 11–1
display components 11–1
Restore Security Defaults 5–5
restore the factory settings 5–2
restoring the hard drive 8–2
right-side components 2–8
RJ-11 (modem) jack
location 2–7
pin assignments 9–4
spare part number 3–4, 3–8
RJ-45 (network) jack
location 2–7
pin assignments 9–4
RTC battery
part number 3–4, 3–12
removal 4–36
Run-In Test 5–3
S
SATA (Serial Advanced Technology Attachment) 5–4
scheduling automatic backups
Windows Vista 8–1
Windows XP 8–4
Screw Kit
contents 3–11
spare part number 3–11, 3–14
screw listing 7–1
secondary battery fast charge 5–4
security cable slot 2–8
Security menu 5–3
security, product description 1–4
serial number 3–1, 4–5
service considerations 4–1
serviceability, product description 1–4
speaker assembly
removal 4–25
spare part number 3–4, 3–14
speakers, product description 1–3
specifications
display 6–2
DVD+/-RW SuperMulti Double-Layer Drive 6–3
DVD+/-RW SuperMulti Double-Layer Drive with
LightScribe 6–4
DVD/CD-RW Combo Drive 6–3
DVD-ROM Drive 6–4
hard drive 6–2
I/O address 6–6
system DMA 6–5
system interrupt 6–5
system memory map 6–8
static-shielding materials 4–3
system backup 8–1
Index–4
system board
removal 4–34
spare part number 3–4, 3–13, 4–34
System Configuration menu 5–1
system DMA specifications 6–5
system interrupt specifications 6–5
system memory map 6–8
WLAN module
illustrated 3–6
removal 4–14
spare part number 3–6, 3–7, 3–12, 4–13
WLAN module compartment cover 3–4
WXGA display specifications 6–2
T
thermal material 3–5
thermal module, spare part number 3–5
tools required 4–1
top components 2–2
top cover
removal 4–21
spare part number 3–4, 3–14
TouchPad 2–2
TouchPad buttons 2–2
TouchPad scroll zone 2–2
U
Universal Serial Bus (USB) port
location 2–7, 2–8
pin assignments 9–5
unknown password 4–4
USB legacy support 5–1, 5–4
V
volume down button 2–4
volume down light 2–6
volume mute button 2–4
volume scroll zone 2–4
volume up button 2–4
volume up light 2–6
W
warranty period 3–1
webcam
location 2–1
product description 3–3
removal 4–28
spare part number 3–3, 3–13, 4–28
webcam light 2–1
Windows applications key 2–5
Windows Backup untility 8–4
Windows Backup utility 8–4, 8–5
Windows logo key 2–5
Windows recovery 8–4, 8–5
Windows Vista operating system DVD 8–3
wireless antennae
location 2–1
product description 1–2, 1–3
wireless button 2–4
wireless light 2–6
wireless module compartment 2–9
Index
Index–5
Download PDF

advertising