Waveform Generator System U8793,MR8847A

Waveform Generator System U8793,MR8847A
Waveform Generator System
Solutions Catalog
Arbitrary Waveform Generator Unit U8793 and Memory
HiCorder Combining Generator and Memory Functions
Memory HiCorders make testing and experimentation convenient.
Combine generating and recording functions
15 V Max. Output
NEW
Arbitrary Waveform Generator Unit U8793
10 mHz to 100 kHz
Output Frequency Range (Function Generator Mode)
Memory HiCorder MR8847A
NEW
2 MHz Max.
D/A refresh rate (Arbitrary Waveform Mode)
2
Generate and record at the same time with the same instrument
Combining a Memory HiCorder and the Arbitrary Waveform Generator Unit U8793 gives you a function
generator mode, arbitrary waveform generator mode, and waveform measurement mode in a single unit.
This makes it easy to observe waveforms while varying test conditions, such as changing the signal's amplitude
and frequency as well as programming various waveforms to output in order.
Example applications
Observe waveforms while varying the output conditions to a circuit board
Conventional procedure
Voltage inputs only
Circuit Boards
Generate
Record
Arbitrary Waveform
Generator
Waveform recorder
▼
Arbitrary Waveform
Generator Unit
U8793 installed
MR8847A + U8793
Circuit Boards
Generate
Record
MR8847A
3
Output recorded waveforms without modification
The combination of a a Memory HiCorder and the Arbitrary Waveform Generator Unit U8793 lets you output
actual waveforms captured from a test vehicle without modification for later use in standalone testing.
What’s more, the U8793 can generate isolated output of up to 15 V without a generator or amplifier, as well as
meet traditional requirements for generating output while varying the signal’s amplitude and frequency.
Example applications
Testing of electronic control boards for automobiles
Conventional procedure
Electronic Control Boards
Output recorded
waveforms
Record
Record vehicle data
Generate
Waveform
recorder
Arbitrary Waveform
Generator
Standalone testing
Amplifier
▼
MR8847A + U8793
Electronic Control Boards
Output recorded
waveforms
Record
Generate
Standalone testing
Record vehicle data
MR8847A
With the Arbitrary Waveform Generator Unit installed,
generate signals of up to 15 V without an amplifier.
Process actual waveforms
for reproducibility testing
15V Max. output range
Without connecting an amplifier externally, you can directly apply
a signal simulating output from automobile sensors.
▼
Use the Waveform Maker SF8000 to reproduce signals recorded
with the Memor y HiCorder and perfor m calculations and
processing to create and output an arbitrary waveform.
Avoid amplifier noise
Direct application eliminates amplifier noise and stabilizes output.
Waveform Maker SF8000
Record
Direct output waveforms
↓
↓
Observed waveform of 15 V output magnified 20x (100 mV/DIV)
100 mV
↓
↓
100 mV
Waveform editing
Actual waveform
Generate
Processed waveform
▼
Output waveforms when
combined with an amplifier
4
Easy settings to improve efficiency
Efficient generation of recorded measurement data is important. Registering waveforms on the Memory
HiCorder makes it easy to configure the generator output. You can also use program settings on the Memory
HiCorder to output a variety of patterns.
Waveform
registration
Repeated generation of recorded waveforms
Data number
Waveform registration from measurement data
Channel
Top position
Data number
Conv ratio
Name
Data start position ►
▼
Ch1
100
20000
1.5
TEST-1
Register waveforms by "clipping" the desired
signal from the measurement data
▼
Generate registered waveforms "as is"
Output settings
Set the data name for the arbitrary waveform that you registered
and the number of loops to be generated
Registered waveform
(sample image)
Program
Link together to generate a variety of waveforms
Arbitrary waveform
pattern 1
Sine wave
Square wave
Arbitrary waveform
pattern 2
▼
*1
Pattern 1 for 1 s
*1
Sine wave for 1 s
*1
Square wave for 1 s
Pattern 2 for 500 ms
*1. Approximately 20 μs is required for the switch between each step.
Output
settings
◄ Confirm the progress of the current step.
5
Synchronize output or independently control across all channels
Max. 54 channel generation/isolated output
Create phase settings between channels in the same unit and between
different units.
Modulization of waveform generation
capabilities allows output from 2 channels up to
a maximum of 54 channels.*
You can expand channels without connecting
cables between devices.
Example of 3-unit (6ch) synchronization*
Unit 1
Unit 2
2ch
Unit 3
2ch
Isolation between the Memory HiCorder and
each output channel and between the channels
enables connections with devices that have
different potentials.
2ch
6-channel synchronized output
*
The maximum number of channels varies according to
the Memory HiCorder.
*
The maximum number of channels varies according to the Memory HiCorder.
If the sequence loop has a hold setting, you can release the hold with an
external input signal. There are independent control terminals for each
channel, allowing you to control each channel at an output timing with
arbitrary time lags.
Multi-channel output Memory HiCorder
Please refer to the catalog for each Memory HiCorder model for detailed specifications.
Max. 32 ch
MR8827
MR8740
Max. 54 ch
Hold cancel
Hold cancel
Hold cancel
MR8847A
Waveform Maker SF8000
Max. 16 ch
MR8847-51: 64MW
MR8847-52: 256MW
MR8847-53: 512MW
Hold cancel
The MR8790 Waveform Generator Unit and the MR8791 Pulse Generator Unit do not have phase
control or synchronize control modes.
MR8741
Max. 16 ch
There are three MR8847A models with different memory capacities.
NEW
The Memory HiCorder by itself cannot create arbitrary
waveforms. Use the Waveform Maker SF8000.
Installing the bundled Waveform Maker SF8000 on your computer lets you enter waveforms or enter functions to easily create
waveforms. You can also process actual waveforms to quickly add noise and multiply waveforms.
* This software (including the Instruction Manual in PDF) is on the Application Disk included with the Memory HiCorder.
● Waveform creation
Waveform input
Readable
file formats
Edit entered
waveforms
Calculate entered
waveforms
Waveform display
14 function types: ABS (absolute value), SIN (sine), COS (cosine),
DIFF (differential), INTG (integration), CINT (integer),
EXT (index), LOG (natural logarithm), NRND (random number),
SQUR (square root), RMPD (ramp down), RMPU (ramp up), TRI
(triangular wave), INV (inverted)
7 control words: AREA, END, FOR, NEXT, PERIOD, PI, STEP,
T, TO, V
Set and input a waveform for each step.
● Pulse pattern creation
Input
Readable file
formats
Save file formats
Process actual waveforms
Select basic waveform: sine wave, square wave, triangular wave,
ramp wave, noise, DC
Waveform creation software: SF8000 (FGW), 7990 (WFG)
Arbitrary waveform generator: 7075 (WFG)
Memory HiCorder: MR8847A, MR8847, 8847, MR8827, MR8740,
and MR8741 (MEM)
Power Quality Analyzer: PW3198 (EVT), CSV
Cut, copy, paste, clear
Add, subtract, multiply, normalize, change size, absolute value,
invert, mirror
Enlarge, reduce, scroll, TIME/DIV display, V/DIV display, Point
display (time axis, voltage axis), % display (voltage axis)
Use editor to input, and select range
and edit, including copy, paste, and delete
SF8000 (PLS), CSV
SF8000 (PLS), CSV
Record
Via LAN/media
Edit
SF8000
▼
Step input
Actual waveform input
▼
Function input
Process actual waveforms
Input from file: Memory HiCorder MR8847A, MR8847, 8847,
MR8827, MR8740, and MR8741
Power Quality Analyzer PW3198
CSV (format for Memory HiCorder and this application)
Input with basic waveform: sine wave, pulse wave, triangular
wave, ramp wave, SIN (X)/X wave, EXP wave, noise, DC
Input with drawing tool: free curve, straight line
Load
Generate
Via LAN/storage media
● Operating environment
OS
Memory capacity
Hard disk
Windows7 (32bit/64bit)/Windows8.1 (32bit/64bit)
1GB RAM or more (32bit), 2GB RAM or more (64bit)
10 MB or more free space
● Interface
LAN
Interface
Arbitrary waveforms Select a Unit No. and Channel No. for the Memory HiCorder to
transfer arbitrary waveform data.
Select a Unit No. and pattern for the Memory HiCorder to transfer
Pulse patterns
data.
6
Applications
Automobile and railroad (transport equipment) testing
Vibration reproducibility testing
Use actual waveforms to test control boards for for engine control, airbags, brake
systems, power steering, active suspension, and more.
Make efficient use of actual waveforms obtained from the vehicle when using
a Memory HiCorder.
Use vibration waveforms recorded in the field with the Memory HiCorder
for vibration testing. Efficient reproduction testing at the press of
a button.
Record actual waveforms
Voltage output
Record actual waveforms
Vibration testing equipment
Vehicle sensor
signals such as
torque, rotational
speed, pressure, and
acceleration
Vehicle sensor inspection
Inverter motor performance test
Inspect sensors in automobiles.
Use the Memory HiCorder and arbitrary waveform generator unit to generate
pulse signals to input to sensors, and then record the signals that those
sensors output in return. You can even set the generation voltage to 14 V to
simulate a car battery.
Create and evaluate VVVF control evaluations and PWM waveforms for inverter
motors, air conditioning, lighting equipment, power supplies, and more.
14 V DC pulse generation
Amplifier
Vehicle sensors
Record output waveforms from sensors
Power steering endurance test
Power anomaly simulation
Create power steering operation signals for each pattern.
Create power supply waveforms such as power supply dips, instantaneous
interruptions, and voltage fluctuations for immunity tests to regulate
malfunctions in equipment caused by power supply harmonics, and load
the actual waveforms obtained with the Power Quality Analyzer PW3198 to
perform evaluation testing.
Endurance testing has never been conducted so efficiently.
Output waveforms (examples)
Sine wave
Triangular wave
Ramp up wave
Ramp down wave
Square wave
Sweep output
Pulse wave (variable duty)
Program output
7
Arbitrary Waveform Generator Unit U8793
Specifications
New
feature
CAUTION: Although you can use MR8847 waveform data for output,
you can only use the MR8847A for waveform generation.
Accuracy guaranteed for 1 year;
Post-adjustment accuracy guaranteed for 1 year
Common specifications
Accuracy guarantee conditions
Temperature and humidity at which accuracy is guaranteed: 23°C ±5°C
(73°F ±9°F) and 80% rh or less
Warm-up time: 30 minutes or more
Power supply frequency for Memory HiCorder connected to
U8793: 50 Hz/60 Hz ±2 Hz
Number of output channels
2 channels per unit
Output terminal
SMB terminal
Output type
Unbalanced output (floating)
Maximum rated voltage to
ground
33 V AC rms or 70 V DC
(Between each output channel and the main unit, between the
channels and external I/O terminals, and between the output
channels)
Sweep function specifications
Sweep waveforms
Non-DC function generation waveforms and arbitrary waveforms
Sweep form
Linear
Sweep targets
FG waveforms: Frequency, amplitude, offset, duty (pulse waves only)
(Frequency, amplitude, and offset can be swept at the same time.)
Arbitrary waveforms: Clock frequency, amplitude, offset (Clock
frequency, amplitude, and offset can be swept at the same time.)
Sweep time setting range
10 μs to 1000 s (setting resolution: 10 μs)
Program specifications
Sequence length
Max. 128 steps linked for output
Step control
FG waveforms, sweep waveforms, and arbitrary waveforms can be
set for each step.
Expected transient overvoltage: 330 V
Number of loops (sweep wavefor ms) and out put time (FG
waveforms, arbitrary waveforms) can be set for each step.
Maximum output voltage
-10 V to 15 V
Amplitude setting range
0 V to 20 V p-p (setting resolution: 1 mV)
Hold settings
DC offset setting range
-10 V to 15 V (setting resolution: 1 mV)
Output time setting range
10 μs to 1000 s (FG waveform, arbitrary waveform)
Output impedance
1 Ω or less
Number of step loops setting range
1 to 1000 times (sweep waveform)
Max. output current
±10 mA (per channel)
1.5 kΩ or more
Number of total loops setting
range
1 to 50000 times, or ∞
Allowable load resistance
Output type
Waveform output, open, shorted
Monitor functions
Display step number, number of step loops, and total number of
loops while the program is running.
FG functional specifications
On/Off can be set for each step.
Other specifications
Output waveforms
Sine wave, square wave, pulse wave(duty ratio variable), triangular
wave, ramp wave, DC
Output frequency range
0 Hz to 100 kHz (setting resolution: 10 mHz)
Output frequency accuracy
± 0.015% of setting
DC output accuracy
± 0.05% of setting ± 10 mV
DC output temperature
characteristics
(± 0.005% of setting ± 1 mV)/°C
Output start/stop
Key operation of Memory HiCorder and signals to external control
terminal
Amplitude accuracy
± 0.5% of setting ± 10 mVp-p (10 mHz to 10 kHz)
External input
When using program functions, use an external low-level signal
input to release the hold and move to the next step.
Channel synchronization
Set phase between unit channels or between units
Self-test function
Monitor output voltage values
Monitor resolution: 10 mV
Monitor accuracy: ±3.0% f.s. (F.s.=15 V)
± 0.8% of setting ± 10 mVp-p (more than 10 kHz to 50 kHz)
Control voltage level: 3.5 V to 5.0 V (HIGH level), 0 V to 0.8 V
(LOW level)
± 1.0% of setting ± 10 mVp-p (more than 50 kHz to 100 kHz)
Amplitude temperature
characteristics
(± 0.05% of setting ± 1 mVp-p)/°C
DC offset accuracy
± 0.5% of setting ± 10 mV
DC offset temperature
characteristics
(± 0.05% of setting ± 1 mV)/°C
Output format: Open drain output (active low, with 5V voltage
output)
Phase difference setting range
-360° to 360° (setting resolution: 0.1°)
Jitter
Output voltage level: 4.0 V to 5.0 V (HIGH level) 0 V to 0.5 V
(LOW level), Max. On/Off capacity: 5 V to 30 V DC, 50 mA
Within 50 ns p-p (square wave, pulse wave, triangular wave, ramp wave)
Pulse wave duty setting range
0.1% to 99.9% (setting resolution: 0.1%)
Enabled for a pulse width of 500 ns or more
Pulse wave duty accuracy
Period ±0.1% (10 mHz to 5 kHz)
Period ±0.5% (more than 5 kHz to 20 kHz)
Period ±1.0% (more than 20 kHz to 100 kHz)
Arbitrary waveform generation specifications
Output waveforms
Response pulse width: 100 μs or more (LOW level)
External output
External I/O terminal
Push-button terminal block
Waveform output display
Red LED On when waveform is output, and Off when output is
OFF.
General specifications
Operating temperature and
humidity range
According to the Memory HiCorder installed with the U8793
Operating environment
According to the Memory HiCorder installed with the U8793
Wavefor m s mea su red w it h Memor y H iCorde r M R8847A ,
MR8847, 8847, MR8827, MR8740, and MR8741
Storage temperature and
humidity
Temperature: -20°C to 50°C (-4°F to 122°F), Humidity: 80% rh or
less (no condensation)
Waveforms created with Waveform Maker SF8000
Standard compliance
Safety: EN61010
EMC: EN61326
Waveforms saved with Waveform Generator 7075*1
Waveforms measured with Power Quality Analyzer PW3198*1
Dielectric withstand voltage
*Logic waveforms are not supported.
Voltage axis resolution
16 bits
Waveform memory capacity
256 kW/ch. × 8 blocks
Low-pass filter
2-stage LPF, 50 Hz to 1 MHz (14 steps in 1-2-5 progression)
D/A refresh rate
Max. 2 MHz (setting resolution: 10 mHz)
Clock frequency accuracy
±150 ppm (Clock frequency jitter: within 50 ns p-p)
Delay
-250.000 to 250.000 (Setting is possible in units of 1 data point.)
Number of loops
1 to 50000 times, or ∞
*1.Prior conversion using the Waveform Maker SF8000 application software is required.
Model : ARBITRARY WAVEFORM GENERATOR UNIT U8793
Model No. (Order Code) (Note)
(For the MR8847A or other)
Options
CONNECTION CABLE L9795-01
Maximum rated voltage to ground:
33 V AC rms or 70 V DC
SMB terminal - alligator clip
Cord length: 1.5 m (4.92 ft)
CONNECTION CABLE L9795-02
Maximum rated voltage to ground:
33 V AC rms or 70 V DC
SMB terminal - BNC terminal
Cord length: 1.5 m (4.92 ft)
350 V AC (sensed current: 1 mA)
(Between each output channel and the main unit, between the
channels and external I/O terminals,
and between the output channels)
Waveforms created as CSV-format files*1
U8793
Output when waveform is output
Dimensions and mass
Approx. 106 mm (4.17 in) W × 19.8 mm (0.78 in) H × 196.5 mm
(7.74 in) D, approx. 250 g (8.8 oz)
The operation manual is included in the "Application Disk", bundled with the Memory HiCorder.
Set example (Generation: 8ch, Input: 8ch)
MEMORY HiCORDER
ARBITRARY WAVEFORM
GENERATOR UNIT
ANALOG UNIT
CONNECTION CABLE
MR8847-51
U8793
1 unit
4
8966
L9795-01
4
8
CONNECTION CORD
L9198
8
MR8847-51 specifications overview
Number of input units
8 analog units
Maximum sampling rate
Frequency
characteristics
Memory capacity
16 analog channels + 16 logic channels
20MS/sec
DC to 5 MHz
(-3dB, when using 8966)
Total 64M words
8966 specifications overview
No. of channels
Measurement range
2ch, voltage input
5 mV to 20 V/div, 12 ranges
Full scale: 20 div
Related Products
Generator units for expanding the practical applications of the Memory HiCorder.
Use in various combinations with measurement units for performing tests.
Waveform Generator Unit MR8790
General specifications
NEW
Accuracy guaranteed for: 1 year Post-adjustment accuracy guaranteed for 1 year
Pulse Generator Unit MR8791
General specifications
NEW
Accuracy guaranteed for 1 year
Number of output channels
4ch/unit (isolated between unit and output, and between all channels)
Self-test function
Included (voltage/current monitor)
Voltage/current monitor
mode (selectable)
Resolution: 5 μA (current monitor), 10 mV (voltage monitor)
Monitor accuracy: ±3.0 % f.s.
(f.s.=10 V: voltage monitor, f.s.=5 mA: current monitor)
Max. output current
±5 mA
Allowable load resistance
2 kΩ or more
Output terminal
SMB terminal
Output configuration
Waveform output, open, shorted
Output relay
Switch time
5 ms or less
Output protection
Limited to 40 mA output current (when an output short-circuit occurs)
Output mode 3
Output/Open (= self diagnostic) (common 8-channel switching)
Maximum rated voltage to
ground
33 V AC rms or 70 V DC
(Between each output channel and the main unit, and between the
output channels)
Expected transient overvoltage: 330 V
Open collector output
regulation (startup time
(10% - 90%))
5 μs (max.) (Load capacity: 1000 pF, Pull-up resistance: 1 kΩ)
Dielectric withstand voltage
350 V AC (sensed current: 1 mA)
(Between each output channel and the main unit, and between the
output channels)
Self-test function
Detected voltage: H level: 3.4 V or more, L level: 1.6 V or less
Relay switch time
5 ms or less
Standard compliance
Safety: EN61010
EMC: EN61326
Operating temperature and
humidity range
33 V AC rms or 70 V DC (between each output channel and the main unit)
Expected transient overvoltage: 330 V
According to the Memory HiCorder installed with the MR8790
Maximum rated voltage to
ground
Dielectric withstand voltage
Operating environment
According to the Memory HiCorder installed with the MR8790
350 V AC (sensed current: 1 mA)
(Between each output channel and the main unit, and between the
output units)
Storage temperature and
humidity
-20°C to 50°C (-4°F to 122°F), and 90% rh or less (no condensation)
Standard compliance
Safety: EN61010
EMC: EN61326
External dimensions
Approx. 106 mm (4.17 in) W × 19.8 mm (0.78 in) H × 196.5 mm (7.74 in) D
(not including protrusions)
Operating temperature and
humidity range
According to the Memory HiCorder installed with the MR8791
Weight
Approx. 230 g (8.1 oz)
Operating environment
According to the Memory HiCorder installed with the MR8791
Storage temperature and
humidity
-20°C to 50°C (-4°F to 122°F), and 90% rh or less (no condensation)
External dimensions
Approx. 106 mm (4.17 in) W × 19.8 mm (0.78 in) H × 196.5 mm (7.74 in) D
(not including protrusions)
Weight
Approx. 230 g (8.1 oz)
Amplitude
DC offset
DC output
Output mode 1
Pattern output/Pulse output (common 8-channel switching)
Output mode 2
Logic output/Open collector output
(Can be set for each of the 8 channels)
Output voltage level: 0 V - 5 V
(H level: 3.8 V or more, L level: 0.8 V or less)
Rated current: ±5 mA
Open collector
output
Absolute maximum rated voltage for collector/
emitter: 50 V
Overcurrent protection: 100 mA
(Logic/Open collector switch, Output/Open (self-diagnostic) switch)
±10 V
16bit
Setting range: DC, 0 Hz to 20 kHz (sine wave)
Setting resolution: 1 Hz
Frequency accuracy: ±0.01% of setting
Setting range: 0 V to 20 V p-p
Setting resolution: 1 mV
Amplitude accuracy:
±0.25% of setting ±2 mV p-p (1 Hz to 10 kHz)
±0.6% of setting ±2 mV p-p (more than 10 kHz to 20 kHz)
Setting range: -10 V to 10 V
Sum of amplitude and DC offset is limited to a peak value of ±10 V.
Setting resolution: 1 mV
Offset accuracy: ±3 mV
Output accuracy: ±0.6 mV
Pulse output specifications
Output frequency
Model : WAVEFORM GENERATOR UNIT MR8790
Setting range: 0 Hz to 20 kHz (Can be set for each of the 8 channels)
Setting resolution: 0.1 Hz
Frequency accuracy: Refer to the time axis accuracy of the Memory
HiCorder in which the MR8791 is installed.
Duty
Setting range: 0.1% to 99.9%, 0, 100% (DC)
Setting resolution: 0.1%
Duty accuracy: Refer to the time axis accuracy of the Memor y
HiCorder in which the MR8791 is installed.
Min. pulse width
The operation manual is included in the "Application Disk", bundled with the Memory HiCorder.
1 μs
Pattern output specifications
Clock frequency
Model No. (Order Code) (Note)
MR8790
8ch/unit (isolated between unit and output)
(Not isolated between each channel (common ground))
(Output connector frame not isolated (main unit grounded))
Logic output
Voltage output specifications
Maximum output voltage
Resolution
Output frequency
Number of output channels
Range: 0 Hz to 120 kHz (common to 8 channels)
Setting resolution: 10 Hz
(For the MR8847A or other)
Sine wave (20 kHz max.) and DC voltage output
Output configuration of 4 channels per unit.
High-precision DC output with an output accuracy
of ±0.6 mV allows output that simulates voltage
fluctuations for minute sensor output.
Options
Frequency accuracy: Refer to the time axis accuracy of the Memory
HiCorder in which the MR8791 is installed.
Memory (pattern)
2048 word (16384 bit=2048 word×8 bit/word)
The operation manual is included in the "Application Disk", bundled with the Memory HiCorder.
Model : PULSE GENERATOR UNIT MR8791
Model No. (Order Code) (Note)
MR8791
CONNECTION CABLE L9795-01
Maximum rated voltage to ground:
33 V AC rms or 70 V DC
SMB terminal - alligator clip
Cord length: 1.5 m (4.92 ft)
(For the MR8847A or other)
Pulse output/Pattern output,
Logic/Open collector output
Output configuration of 8 channels per unit.
You can select pulse output or edited pattern output
(common switching for all channels). Furthermore,
you can set the output format to TTL level logic
out put and open collector out put. (Settable for
individual channels)
CONNECTION CABLE L9795-02
Maximum rated voltage to ground:
33 V AC rms or 70 V DC
SMB terminal - BNC terminal
Cord length: 1.5 m (4.92 ft)
Note: Company names and Product names appearing in this catalog are trademarks or registered trademarks of various companies.
HIOKI (Shanghai) SALES & TRADING CO., LTD.
TEL +86-21-63910090 FAX +86-21-63910360
http://www.hioki.cn / E-mail: [email protected]
DISTRIBUTED BY
HIOKI SINGAPORE PTE. LTD.
TEL +65-6634-7677 FAX +65-6634-7477
HEADQUARTERS
E-mail: [email protected]
81 Koizumi, Ueda, Nagano, 386-1192, Japan
TEL +81-268-28-0562 FAX +81-268-28-0568
HIOKI KOREA CO., LTD.
http://www.hioki.com / E-mail: [email protected] TEL +82-2-2183-8847 FAX +82-2-2183-3360
E-mail: [email protected]
HIOKI USA CORPORATION
TEL +1-609-409-9109 FAX +1-609-409-9108
http://www.hiokiusa.com / E-mail: [email protected]
All information correct as of Nov. 8, 2016. All specifications are subject to change without notice.
U8793E2-6YB
Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement