1. Arming the Alarm: Turn the ignition key and go out the car. Press

1. Arming the Alarm: Turn the ignition key and go out the car. Press
1.
Arming the Alarm:
Turn the ignition key and go out the car. Press the
icon on the remote. The alarm will beep, hazard lights
will flash once, car will close. The alarm is arming for 15 seconds. After this period the indicator (LED) will
flash slowly, indicating the full arming of the alarm.
2.
Disarming the Alarm:
Press
icon on the remote. The door will open. The alarm will beep, hazard lights will flash twice, car will
open. The indicator (LED) will stop flashing.
3.
Silent Arming:
Press icon on the remote. The hazard lights will flash once, car will close. The alarm is arming for 15
seconds. After this period the indicator (LED) will flash slowly, indicating the full arming of the alarm.
4.
Remote Trnk Release:
Press and hold
automatically.
5.
icon on the remote for 2 seconds while the alarm is disarmed. The trunk opens
Auto Rearming (optional):
If after disarming the alarm for 15 seconds none of the door is opened, the alarm will beep and LED will
flash. After another 15 seconds the alarm will arm. If you want to turn on/ turn off this function turn the
ignition key, hold the
6.
icon and wait for the alarm beeping and LED flashing.
Door Open Alert (optional - JUMPER):
The hazard lights warn about open door. Turning off the function is possible by removing the jumper
(JUMPER).
7.
Ignition Controlled Door Lock/Unlock (optional - JUMPER):
Your vehicle will have the ability to automatically lock the doors after turning on the ignition key (after 10
seconds) and automatically unlock when the ignition key is turned off. If, during the starting a car, any of
the door is open, the function will not work. Turning off the function is possible by removing the jumper
(JUMPER).
8.
Car Locator:
In the parking lot or at night, when you cannot locate the car, press and hold
for 4 seconds.
9.
icon. The siren will sound
Emergency Alarm Disarming:
When the alarm is armed and you lost your remote control or the batteries are discharged, you can disarm
the alarm by opening door – siren will sound, turn on the ignition key and press hidden Reset Switch.
10. "Valet" Mode:
Useful in situations when the alarm should not be active - for example, in a car wash. To enable/disable all
functions of the alarm, turn on the ignition key and open the door. Next press and hold the Reset Switch for
5 seconds.
11. "Panic" Mode:
Press and hold the
icon on the remote for 5 seconds or press the
will sound and hazard lights will flash for 20 seconds.
while the alarm is armed. The siren
12. Silent/ Loud Closing Mode(optional):
The alarm must be disarmed. Press and hold the
and
icons in the same time for 2 seconds. The alarm
will confirm turning on/turning off the mode through visual and sound signals.
13. Shock sensor (optional):
The alarm must be armed. If you want to turn on/turn off the shock sensor, press and hold the
and
icons in the same time for 2 seconds. The alarm will confirm turning on/turning off the mode through visual
and sound signals.
14. Timer Door Lock:
The function is available by JUMPER.
15. Protection:
If the alarm is armed, and door or bonnet is opened, the alarm will warning you through sound and visual
effects - 3 cycles, 45seconds each. After this 3 cycles, if the door or the bonnet is not closed, the siren will
turn on and the hazard lights will flash continuously until disarming the alarm.
16. Alarm status indicator (LED):
FUNCTION STATUSLED
Arm
Alarm has been violate
Passive immobilizing
Disarm and before enter Auto Rearming count-down
Disarm + Ignition “ON”
Valet Mode
LED
Regular flashing
Fast flashing
Slow flashing
ON
OFF
ON
17. Remember Car Alarm Remotes:
When the alarm is connected according to the diagram, open the door. Turn the key to ON position and turn
back to OFF position. Leave key in ON position. The siren will sound once. Press the
icon, the LED will
flash permanently. To confirm function please press any button – the siren will sound and indicator will go
out. You can remember up to 6 remotes. Next turn off the indicator and leave programming mode in the
same time.
18. Removing Alarm Remotes from Memory:
In programming mode press reset button once. The siren will sound and the remote will be removed.
19. Function selected via JUMPER:
JMP
S0
S1
S2
FUNCTIONS SELECTABLE
Ignition Controlled Door Lock/Unlock
Door Open Alert
Timer Door Lock
Default
+
0,8 sec.
Active
+
+
3,5 sec.
Central Lock Installation
Installation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement