1
2
3
4
5
6
7
8
Hinge - Latch Kit Installation Instructions
A
(Cat 598-NHL22M)
ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.
This accessory kit, when properly installed, will provide UL Type 3R, 4/4X, 12 and 13 protection for the enclosures listed in the table.
Bulletin 598 Enclosure Kits
B
C
Enclosure with
Enclosure with
Length
Width
Number of
Clear Cover
Opaque Cover
(in.)
(in.)
Kits
Cat No.
Cat No.
598-BS885C
598-BS885
7 - 1/2
598-BS1187C
598-BS1187
598-BS1587C
Location of
Location of
Hinges from Short Sides Latches from Short Sides
Required
of Enclosure (in.)
of Enclosure (in.)
7 - 1/2
1
2
2
11
7 - 1/2
1
2 - 1/4
2 - 1/4
598-BS1587
15
7 - 1/2
1
3 - 1/4
3 - 1/4
598-BS11115C
598-BS11115
11
11
1
2 - 1/4
2 - 1/4
598-BS13115C
598-BS13115
13
11
1
2 - 1/2
2 - 1/2
598-BS15117C
598-BS15117
15
11
1
3 - 1/4
3 - 1/4
598-BS22115C
598-BS22115
22
11
2
2-1/2, 9
2-1/2, 9
598-BS22157C
598-BS22157
22
15
2
2-1/2, 9
2-1/2, 9
Each Enclosure Kit Contains
D
Hinges
Latch
Hook
Qty. 2
Qty. 2
Latches
Qty. 2
Threaded
Plates
Qty. 8
Gaskets
Qty. 16
Screws
M4 or #8
Qty. 16
Plugs
Qty. 4
Latch Release
Instruction Label
Qty. 1
E
Tools required
#2 Phillips
or
Posidrive
Screwdriver
1/16"
Drill Bit
for
Pilot Hole
Electric
Drill
5/32" or M4
Drill Bit
for
Final Hole
F
G
REFERENCE
REVISION
AUTHORIZATION
1
1024601
THIS DRAWING IS THE PROPERTY OF
ROCKWELL AUTOMATION, INC.
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL AUTOMATION, INC.
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
.XX:
N/A
.XXX:
N/A
E - DOC
BULLETIN 598 HINGE-LATCH
INSTALLATION INSTRUCTION SHEET
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
H
LOCATION: MILWAUKEE, WISCONSIN U.S.A.
DR.
ANGLES:
42052
N/A
CHKD.
APPD.
G. Ushakow
M. Jutz
M. O'Dell
DATE
DATE
DATE
1-30-07
1-30-07
1-30-07
DWG.
SIZE
B
SHEET
1
OF
4
42052-163
B-vertical.ai
1
2
1
A
3
4
5
6
7
8
Drill Holes in Base
IMPORTANT: Drill bit diameter to not exceed .161 in (4.1 mm). Do not drill into the short sides of the enclosure.
7-1/2" thru 15" Long Enclosures
(598-BS885_ -BS1187_, -BS1587_, -BS11115_,
-BS13115_, -BS15117_)
22" Long Enclosures
(598-BS22115_, -BS22157_)
Note: Drill 1/16" pilot hole first, then drill 5/32" or 4mm
hole for two latches and two hinges.
Note: Drill 1/16" pilot hole first, then drill 5/32" or 4mm
hole for four latches and four hinges in locations as
circled in diagram.
B
Hinge Side
2-1
Latch Side
1
n.
/2 i
/2 i
2-1
n.
9 in
.
9i
9 in
.
9i
n.
Hinge Side
Latch Side
C
n.
2-1
2
2-1
n.
1
2
D
n.
/2 i
/2 i
2
Latch Installation
IMPORTANT: Each latch assembly must have one gasket installed on each side of enclosure wall.
1
Preassemble latch, screws and gasket
Incorrect position
of wire
Correct position
of wire
6 - 12 lb-in
E
4
3
2
Extruded
side facing
away from
gasket
F
(2)
G
REFERENCE
REVISION
AUTHORIZATION
1
1024601
THIS DRAWING IS THE PROPERTY OF
ROCKWELL AUTOMATION, INC.
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL AUTOMATION, INC.
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
.XX:
N/A
.XXX:
N/A
E - DOC
BULLETIN 598 HINGE - LATCH
INSTALLATION INSTRUCTION SHEET
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
H
LOCATION: MILWAUKEE, WISCONSIN U.S.A.
DR.
ANGLES:
42052
N/A
CHKD.
APPD.
-------------------
DATE
DATE
DATE
-------------------
DWG.
SIZE
B
SHEET
2
OF
4
42052-163
B-vertical.ai
1
2
3
A
3
4
5
6
7
8
Hinge Installation
IMPORTANT: Each hinge assembly must have one gasket installed on each side of enclosure wall.
1
Preassemble hinge, screws and gasket
4
6 - 12 lb-in
B
3
2
Extruded
side facing
away from
gasket
C
4
Remove Captive Plastic Screws (If Present)
from Cover
D
5
Drill Holes in Cover
IMPORTANT: Drill bit diameter to not exceed .161 in (4.1 mm). Do not drill into the short sidess of the enclosure.
7-1/2" thru 15" Long Enclosures
(598-BS885_ -BS1187_, -BS1587_, -BS11115_,
-BS13115_, -BS15117_)
22" Long Enclosures
(598-BS22115_, -BS22157_)
Note: Drill 1/16" pilot hole first, then drill 5/32" or
4mm hole for two latch hooks and two hinges.
Note: Drill 1/16" pilot hole first, then drill 5/32" or 4mm hole
for four latch hooks and four hinges in locations as circled in
diagram.
Hinge Side
2-1
Latch Hook
Side
/2 i
E
1
2
/2
2-1
n.
in.
n.
9 in
.
9i
9 in
.
9i
2-1
n.
/2 i
2
/2
2-1
n.
in.
F
1
2
(3)
G
REFERENCE
REVISION
AUTHORIZATION
1
1024601
THIS DRAWING IS THE PROPERTY OF
ROCKWELL AUTOMATION, INC.
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL AUTOMATION, INC.
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
.XX:
N/A
.XXX:
N/A
E - DOC
BULLETIN 598 HINGE-LATCH
INSTALLATION INSTRUCTION SHEET
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
H
LOCATION: MILWAUKEE, WISCONSIN U.S.A.
DR.
ANGLES:
42052
N/A
CHKD.
APPD.
-------------------
DATE
DATE
DATE
-------------------
DWG.
SIZE
B
SHEET
3
OF
4
42052-163
B-vertical.ai
1
2
6
A
3
4
5
6
7
8
Latch Hook Installation
IMPORTANT: Each latch hook must have one gasket installed on each side of enclosure wall.
1
Preassemble latch hook, screws and gasket
IMPORTANT: If the hook does not lie flat, install on other side of cover.
Hook must lie flat against cover
Hook can not be tilted after installation
B
3
6 - 12 lb-in
4
Extruded side
facing
away from
gasket
C
2
7
D
Cover Installation
IMPORTANT: Each hinge assembly must have one gasket installed on each side of enclosure wall.
1
3
6 - 12 lb-in
Click
E
2
5
4
Latch Release Label
Click
Extruded
side facing
away from
gasket
6
F
42052-163-01 (1)
Printed in Korea
-01
1
FOUR PAGES
TWO SIDES PRINTED - STAPLED
BODY STOCK WHITE
BODY INK BLACK
PART
NO.
CHG.
LTR.
MATERIAL
G
REFERENCE
REVISION
AUTHORIZATION
1
1024601
8-1/4" W x 11-3/4" H
(A4)
4-1/8" W x 5-7/8" H
FLAT
FOLD
SIZE
THIS DRAWING IS THE PROPERTY OF
ROCKWELL AUTOMATION, INC.
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL AUTOMATION, INC.
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
.XX:
N/A
.XXX:
N/A
E - DOC
BULLETIN 598 HINGE - LATCH
INSTALLATION INSTRUCTION SHEET
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
H
LOCATION: MILWAUKEE, WISCONSIN U.S.A.
DR.
ANGLES:
42052
N/A
CHKD.
APPD.
-------------------
DATE
DATE
DATE
-------------------
DWG.
SIZE
B
SHEET
4
OF
4
42052-163
B-vertical.ai
">
