Honda 08E91-E54-100, 08E92-T2A-100A, 08E92-T2A-100B Remote Control Engine Starter Installation Instructions
Below you will find brief information for Remote Control Engine Starter 08E91-E54-100, Remote Control Engine Starter 08E92-T2A-100A. Install this {detected_brand} remote control engine starter on your {detected_brand} vehicle, follow step-by-step instructions and attach the {detected_brand} antenna to your windshield. Using the control unit, connect the {detected_brand} harness to the vehicle's wiring and secure it to the vehicle frame. Finally, register the remote control engine starter using the supplied {detected_brand} HDS/MVCI tester and verify that the engine can be started by the transmitter.
Advertisement
Advertisement
INSTALLATION
INSTRUCTIONS
PARTS LIST
Remote Engine Starter Unit Kit
P/N 08E91-E54-100
Transmitter
Accessory
REMOTE CONTROL
ENGINE STARTER
3 Relays
Application
2017 ACCORD
2 AND 4-DOOR
Flange nut
Control unit
18 Wire ties
Publications No.
VERSION 1
Issue Date
JUN 2016
Wire tie with clip
Antenna
6 Urethane tapes
ID label
Remote Control Engine Starter Attachment Kit
P/N 08E92-T2A-100A
(With Keyless Access System)
Engine starter harness
Clip
Caution label
Fuse label
Control unit bracket
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
08E92-T2A-1A00-90
1 of 29
Accessory User’s Information Manual 6 Urethane tapes
Clip
Quick Start Guide
Remote Control Engine Starter Attachment Kit
P/N 08E92-T2A-100B
(Without Keyless Access System)
Engine starter harness
Caution label
Fuse label
Control unit bracket
Accessory User’s Information Manual
3 Relays
Quick Start Guide
Flange nut
18 Wire ties
Wire tie with clip
2 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriver
Phillips screwdriver
Ratchet
10 mm Socket
10 mm Open end wrench
Isopropyl alcohol
Shop towel
Tape measure
Scissors
HDS/MVCI
Masking tape
Diagonal cutters
Ruler
Tape
Utility knife
The following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Remote Control Engine Starter in the Vehicle
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1.
Disconnect the negative cable from the battery.
2.
Attach the ID label.
• Using isopropyl alcohol on a shop towel, clean the area where the ID label will attach.
• Attach the ID label to the transmitter in the area as shown.
With Keyless Memory Settings
NOTE: The remote is factory set for driver 1 remote control. To program the driver 2 remote, follow the
“REMOTE CONTROL ENGINE STARTER
TRANSMITTER REGISTRATION” instructions on
ISIS.
ID LABEL
TRANSMITTER
ANTENNA
Clean with isopropyl alcohol.
QB20939DH
ENGINE
STARTER
HARNESS
3 RELAYS
3A,
20A or 40A
FUSES
CONTROL
UNIT
QB20940AH
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
3 of 29
Without Keyless Memory Settings
ID LABEL
TRANSMITTER
3.
If equipped, remove the roof console.
• Using a plastic trim tool, pry out and remove the left and right lenses (four retaining tabs each).
• Open the sunglass holder. Remove four screws.
• Remove the roof console (unplug the vehicle connectors).
With Moonroof
VEHICLE
CONNECTORS
Clean with isopropyl alcohol.
QB32111CH
SUNGLASS
HOLDER
(Open.)
4 SCREWS
LEFT
LENS
4 RETAINING
TABS
ROOF
CONSOLE
RIGHT
LENS
4 RETAINING
TABS
QB20901B
4 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
Without Moonroof
VEHICLE
CONNECTORS
5.
Wrap the end of a flat-tip screwdriver with tape.
Locate the slot in the bracket cover, and insert the flat-tip screwdriver into the slot. Push the hook with the screwdriver.
FLAT-TIP
SCREWDRIVER BRACKET COVER
TAPE
HOOK
DRIVER’S
SUNVISOR
FRONT
SUNGLASS
HOLDER
(Open.)
4 SCREWS
ROOF
CONSOLE
(if equipped)
RIGHT
LENS
LEFT
LENS
4 RETAINING
TABS
4 RETAINING
TABS
QB20902A
4.
Remove two sunvisor holders by rotating them 90° counterclockwise.
Make sure the hook slides into the bracket cover.
Push the hook.
While pushing in on the hook, rotate the sunvisor backward about 45°.
QB32101A
6.
While pushing in on the hook, rotate the driver’s sunvisor backward about 45°. Make sure the hook slides into the bracket cover.
NOTE: If the hook did not stay pushed in, return the driver’s sunvisor to its original position and repeat
PASSENGER’S
SUNVISOR
HOLDER
(Rotate.)
DRIVER’S
SUNVISOR
HOLDER
(Rotate.)
QB20903A
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
5 of 29
7.
Remove the driver’s sunvisor (unplug the vehicle connector).
VEHICLE
CONNECTOR
10. Insert a shop towel in the opening between the driver’s A-pillar trim and the dashboard to prevent dropping the A-pillar clips. Take care not to damage the driver’s A-pillar trim.
DRIVER’S
A-PILLAR
DRIVER’S
A-PILLAR TRIM
FRONT
DRIVER’S
SUNVISOR
QB20904A
8.
Pull away the driver’s door opening seal in the area shown.
Pull the clip.
SHOP TOWEL
QB20906A
11. Slide up the driver’s A-pillar trim to remove it from the upper clip. Carefully remove the shop towel and any clips that fell from the driver’s A-pillar trim.
NOTE: The upper clip will stay in the body.
UPPER CLIP
DRIVER’S
A-PILLAR
TRIM
DOOR
OPENING
SEAL
(Pull away.)
2 CLIPS
QB20905A
9.
Pull out on the driver’s A-pillar trim to release the clips.
DRIVER’S
A-PILLAR
TRIM
6 of 29
QB20907A
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
12. Remove the remaining upper clip from the driver’s
A-pillar.
14. If equipped, remove the driver’s dashboard under cover.
2 CLIPS
2 TABS
(Push.)
DRIVER’S
A-PILLAR
UPPER
CLIP
(Discard.)
QB20908A
13. Install the new clip (supplied) to the driver’s A-pillar trim, but do not reinstall the trim at this time.
CLIP
(supplied)
DRIVER’S DASHBOARD
UNDER COVER
(if equipped)
KNOB
(Turn.)
QB20201AB
15. Remove the driver’s dashboard lower cover and unplug the vehicle connectors (if equipped).
VEHICLE
CONNECTORS
(if equipped)
9 CLIPS
DRIVER’S
A-PILLAR TRIM
Q0N0533AH
DRIVER’S DASHBOARD
LOWER COVER
QB20202BB
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
7 of 29
16. Remove the cover. Using the ignition key, unlock the trunk lid/fuel fill door opener, then remove the key.
SELF-TAPPING
SCREW
KEY
Unlock.
6 RETAINING
TABS
COVER
18. Remove the driver’s door sill trim.
4-Door:
Two retaining tabs and four clips.
2 RETAINING TABS
4 CLIPS
TRUNK LID/FUEL
FILL DOOR OPENER
DRIVER’S DOOR
SILL TRIM
QB32110AH
17. Remove one self-tapping screw from the trunk lid/ fuel fill door opener cover.
DRIVER’S DOOR
SILL TRIM
2-Door:
Two retaining tabs and six clips.
QB20804AB
6 CLIPS
2 RETAINING
TABS
DRIVER’S DOOR
SILL TRIM
QB32112AH
8 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
19. Pull away the door opening seal, and remove the driver’s kick panel.
21. Turn the steering wheel 90° clockwise. Using a plastic trim tool, release the retaining tab.
UPPER COLUMN COVER
DOOR OPENING
SEAL
(Pull away.)
2 CLIPS
DRIVER’S
KICK PANEL
QB20805AB
20. Lower the tilt lever, and release the column band. If the vehicle is equipped with keyless access system, reconnect the negative cable to the battery, then press the engine start/stop button to select the ON mode.
STEERING
WHEEL
2 CLIPS
COLUMN
BAND
STEERING
WHEEL
RETAINING
TAB
PLASTIC TRIM
TOOL
QB32114AH
22. Turn the steering wheel 180° counterclockwise.
Using a plastic trim tool, release the retaining tab.
UPPER COLUMN COVER
STEERING
WHEEL
UPPER COLUMN
COVER
QB32113AH
RETAINING
TAB
PLASTIC TRIM
TOOL
STEERING
WHEEL
QB32115AH
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
9 of 29
23. Remove the upper column cover.
2 HOOKS
2 RETAINING
TABS
UPPER
COLUMN
COVER
25. Turn the steering wheel 180° clockwise, and remove the other self-tapping screw from the lower column cover.
QB32116AH
24. Remove one self-tapping screw from the lower column cover.
STEERING
WHEEL
LOWER COLUMN
COVER
26. Remove the lower column cover.
SELF-TAPPING
SCREW
QB32118AH
LOWER COLUMN
COVER
SELF-TAPPING
SCREW
QB32117AH
LOWER COLUMN
COVER
SELF-TAPPING
SCREW
QB32119AH
27. If the vehicle is equipped with keyless access system, press the engine start/stop button to select the OFF mode. Disconnect the negative cable from the battery.
10 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
Installing the Antenna
28. Using scissors, cut one urethane tape in half. Wrap two halves of urethane tape to the antenna cable as shown.
ANTENNA
29. Starting near the antenna end of the cable, wrap one urethane tape around the antenna cable at the measurements shown.
ANTENNA
CABLE
60 mm
(2.4 in.)
ANTENNA
60 mm
(2.4 in.)
ANTENNA
CABLE
220 mm
(8.7 in.)
URETHANE
TAPE
560 mm
(22.0 in.)
ANTENNA
CABLE
URETHANE TAPE
(Cut in half.)
HALVES OF
URETHANE TAPE
(Do not fold the antenna cable.)
QB62501BK
2 URETHANE TAPES
(Cut in half.)
HALVES OF
URETHANE TAPE
QB20901CH
30. Using scissors, cut two urethane tapes in half. Wrap four halves of urethane tape around the antenna cable at the measurements shown.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
11 of 29
31. Attach the antenna.
• Attach masking tape to the windshield at the measurement shown.
With Camera Cover
MASKING TAPE
10 mm (0.4 in.)
CAMERA
COVER
• Fold the adhesive backing of the antenna as shown.
ADHESIVE
BACKING
HEADLINER
Without Camera Cover
MASKING TAPE
50 mm (2.0 in.)
HEADLINER
QB51403BH
ANTENNA
QB51401CH
• Using isopropyl alcohol on a shop towel, clean the windshield where the antenna will attach.
• Attach the antenna with masking tape. Adjust the position of the antenna so there is equal spacing on both sides.
Clean with isopropyl alcohol.
QB51402BH
ANTENNA
HEADLINER
Equal spacing on both sides.
MASKING TAPE ANTENNA
QB51404CH
12 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
• Carefully remove the adhesive backing from the antenna, and attach the antenna to the windshield. Press and hold the antenna firmly in place for 30 seconds.
• Remove the masking tape.
33. Route the antenna cable down the A-pillar as shown.
Using five wire ties, secure the antenna cable to the vehicle harness.
ANTENNA
CABLE
ANTENNA
VEHICLE
HARNESS
5 WIRE
TIES
ADHESIVE
BACKING
(Remove.)
MASKING TAPE
(Remove.)
QB51405CH
32. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner.
HEADLINER
ANTENNA
CABLE
VEHICLE
FRAME
VEHICLE
HARNESS
QB20905AH
34. Pull away the door opening seal. Route the antenna cable down next to the dashboard, and tuck the antenna cable between the driver’s A-pillar and the dashboard. Reinstall the door opening seal.
DRIVER’S
A-PILLAR
DOOR OPENING
SEAL (Pull away)
ANTENNA
CABLE
ANTENNA
ANTENNA
CABLE
DASHBOARD
QB20906BH
QB20904CH
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
13 of 29
Routing the Engine Starter Harness
35. Using isopropyl alcohol on a shop towel, clean the areas where the fuse labels will attach.
20A or 40A
FUSE LABEL
3A FUSE
LABEL
Clean with isopropyl alcohol.
20A or 40A
FUSE
LABEL
Clean with isopropyl alcohol.
38. Using scissors, cut one urethane tape to the measurements shown. Wrap the cut urethane tape around the engine starter harness 5-pin connector.
VIEW FROM
URETHANE SIDE
20 mm (0.8 in.)
ENGINE STARTER HARNESS
5-PIN CONNECTOR
25 mm
(1.0 in.)
URETHANE
TAPE
ENGINE STARTER
HARNESS
3A FUSE
LABEL
ENGINE STARTER
HARNESS RELAY
BLOCK
QB20907AH
36. Attach two 20A fuse labels (with keyless access system) or two 40A fuse labels (without keyless access system) and two 3A fuse labels to the engine starter harness relay block.
37. Install three relays to the engine starter harness relay blocks.
3 RELAYS
QB20909AH
14 of 29
ENGINE
STARTER
HARNESS
RELAY
BLOCKS
QB20908AH
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
39. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Plug the vehicle
5-pin connector into the engine starter harness 5-pin connector.
NOTICE: Make sure the engine starter harness 5-pin
connector is securely connected to the fuse box 5-pin connector. A loose connection can cause the engine to stall.
40. Using two wire ties, secure the engine starter harness to the vehicle harness.
VEHICLE
HARNESS
FUSE BOX
Connector unlock
VEHICLE 5-PIN
CONNECTOR
Connector lock
1
Plug.
2 WIRE
TIES
ENGINE
STARTER
HARNESS
QB20911AH
41. Plug the engine starter harness 4-pin connector into the fuse box.
FUSE BOX
4-PIN CONNECTOR
2
Pull.
1
Push.
3
Unplug.
2
Push.
VEHICLE 5-PIN
CONNECTOR
ENGINE STARTER HARNESS
5-PIN CONNECTORS
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
QB20910CH
AII04162-35 (1606)
ENGINE STARTER HARNESS
4-PIN CONNECTOR
QB20912AH
15 of 29
42. Route the engine starter harness as shown. Remove the tape from the vehicle harness. Do not damage the vehicle harness.
44. Unplug the vehicle 28-pin connector, and plug it into the engine starter harness 28-pin connector. Plug the engine starter harness 28-pin connector into the vehicle 28-pin connector.
FUSE BOX
TAPE
(Remove, if equipped.)
VEHICLE
28-PIN
CONNECTOR
ENGINE STARTER
HARNESS
28-PIN CONNECTORS
ENGINE STARTER
HARNESS 28-PIN
CONNECTOR
VEHICLE
CONNECTORS
QB20913CH
43. Attach the engine starter harness 28-pin connector to the vehicle connector.
VEHICLE
28-PIN
CONNECTOR
VEHICLE
28-PIN
CONNECTOR
ENGINE STARTER
HARNESS 28-PIN
CONNECTOR
QB20914BH
16 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
With Keyless Access System
45. Remove the tape from the engine starter harness
2-pin connector. Unplug the vehicle 2-pin connector, and plug it into the engine starter harness 2-pin connector. Plug the engine starter harness 2-pin connector into the vehicle 2-pin connector.
TAPE
(Remove.)
FUSE
BOX
Without driver’s dashboard under cover
46. Using a utility knife, cut the dashboard insulator as
SLIT
Cut.
If equipped, do not connect.
VEHICLE
2-PIN
CONNECTOR
ENGINE STARTER
HARNESS 2-PIN
CONNECTOR
DASHBOARD
INSULATOR
(Cut.)
BRAKE PEDAL
QB20916AH
With driver’s dashboard under cover
47. Remove the cap from the vehicle bolt.
ENGINE STARTER
HARNESS 2-PIN
CONNECTOR
VEHICLE 2-PIN
CONNECTORS
QB20915CH
CAP
VEHICLE
BOLT
QB20917AH
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
17 of 29
48. Using a utility knife, cut the dashboard insulator to the measurements shown. Do not damage the vehicle panel.
FUSE
BOX
15 mm (0.6in.)
15 mm
(0.6in.)
Cut.
51. Plug the antenna cable connector and engine starter harness 28-pin connector into the control unit.
CONTROL
UNIT
ANTENNA CABLE
CONNECTOR
DASHBOARD
INSULATOR
VEHICLE
BOLT
QB20918AH
49. Using isopropyl alcohol on a shop towel, clean the control unit where the urethane tape will attach.
URETHANE TAPE
(Cut in half.)
CONTROL
UNIT
ENGINE STARTER
HARNESS 28-PIN
CONNECTOR
QB20920AH
52. Install the control unit bracket to the control unit.
CONTROL UNIT
BRACKET
URETHANE
TAPE
Align.
Clean with isopropyl alcohol.
CONTROL UNIT
QB20921AH
QB20919BH
50. Using scissors, cut the urethane tape in half, then wrap the urethane tape around the control unit.
18 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
53. Secure the engine starter harness clip to the control bracket.
ENGINE STARTER
HARNESS CLIP
CONTROL UNIT
55. Using one flange nut, secure the control unit bracket to the vehicle panel as shown.
CONTROL UNIT
BRACKET
QB20922AH
54. Using two wire ties, secure the antenna cable to the engine starter harness.
CONTROL UNIT
BRACKET
FLANGE
NUT
VEHICLE
PANEL
QB20924AH
56. Secure the engine starter harness clip to the vehicle bolt.
ENGINE STARTER
HARNESS CLIP
CONTROL UNIT
BRACKET
ANTENNA CABLE
2 WIRE TIES
CONTROL UNIT
BRACKET
ENGINE STARTER
HARNESS
QB20923AH
VEHICLE
BOLT
ENGINE STARTER
HARNESS
QB20925AH
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
19 of 29
57. Using isopropyl alcohol on a shop towel, clean the control unit bracket where the urethane tape will attach.
URETHANE
TAPE (Cut.)
URETHANE
TAPE
60. Attach the engine starter harness relay blocks to the control unit bracket.
CONTROL UNIT
BRACKET
ENGINE STARTER
HARNESS RELAY
BLOCKS
Cut in
Clean with isopropyl alcohol.
CONTROL UNIT
BRACKET
QB20926AH
58. Using scissors, cut the urethane tape in half as shown, then attach the urethane tape to the control unit bracket.
With driver’s dashboard under cover
59. Reinstall the cap to the vehicle bolt.
CONTROL UNIT
BRACKET
61. Remove the vehicle ground bolt.
QB20928AH
20 of 29
CAP
(reused)
CONTROL UNIT
BRACKET
VEHICLE
BOLT
QB20927AH
VEHICLE
GROUND
BOLT
(reused)
ENGINE STARTER
HARNESS GROUND
TERMINAL
QB20929CH
VEHICLE GROUND
TERMINAL
62. Attach the engine starter harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt.
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
63. Using one wire tie, secure the antenna cable and engine starter harness to the vehicle harness.
WIRE TIE
FUSE BOX
2-PIN
CONNECTOR
(if equipped)
65. Secure the engine starter harness to the hole in the vehicle frame with one wire tie with clip at the white tape on the engine starter harness.
NOTE: If another accessory harness is already attached, align the white tape on the engine starter harness with the clip on the other harness. Using one wire tie with clip, secure the engine starter harness to the other accessory harness.
WHITE TAPE
WIRE TIE
WITH CLIP
ENGINE STARTER
HARNESS
ENGINE
STARTER
HARNESS
ANTENNA
CABLE
VEHICLE
HARNESS
QB20930CH
64. Bundle up the excess antenna cable as shown.
Using two wire ties, secure the antenna cable and engine starter harness to the vehicle harness.
20 mm (0.8 in.) or above.
WIRE TIE
WITH CLIP
OTHER ACCESSORY
HARNESS CLIP
WHITE TAPE
WITH OTHER
ACCESSORY HARNESS
QB20932AH
VEHICLE
HARNESS
ANTENNA
CABLE
(Bundle.)
ENGINE
STARTER
HARNESS
2 WIRE TIES
QB20931DH
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
21 of 29
66. Route the 12-pin/10-pin connector ends of the engine starter harness as shown.
ENGINE STARTER
HARNESS
VEHICLE
HARNESS
69. Route the engine starter harness as shown. Unplug the vehicle 10-pin connector, and plug it into the engine starter harness 10-pin connector. Plug the remaining engine starter harness 10-pin connector into the wiper switch.
ENGINE
STARTER
HARNESS
Inside
VEHICLE
HARNESS
CLIP
WHITE
TAPE
ENGINE STARTER
HARNESS 10-PIN
CONNECTOR
2 WIRE TIES
QB20933AH
67. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie.
68. Using one wire tie, secure the engine starter harness to the vehicle harness.
WIPER
SWITCH
VEHICLE
10-PIN
CONNECTOR
ENGINE STARTER
HARNESS 10-PIN
CONNECTOR
QB20934AH
22 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
70. Using one wire tie, secure the 10-pin connector and the engine starter harness to the vehicle harness.
Do not undue strain to the 10-pin connector cord.
71. Route the engine starter harness as shown. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch.
ENGINE STARTER
HARNESS
ENGINE STARTER
HARNESS
IGNITION
SWITCH
WIRE TIE
10-PIN
CONNECTOR
QB20935BH
ENGINE
STARTER
HARNESS
12-PIN
CONNECTOR
VEHICLE
12-PIN
CONNECTOR
COMBINATION
LIGHT SWITCH
ENGINE STARTER HARNESS
12-PIN CONNECTOR
QB20936AH
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
23 of 29
72. Using three wire ties, secure the engine starter harness to the vehicle harness. Do not secure it to the SRS harness.
NOTE: Make sure that the connectors and harness are not pinched, or are not interfering with the steering wheel when it is moved for adjustment.
Do not pull the 12-pin connector cord wire too tight.
73. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach.
Clean with isopropyl alcohol.
VEHICLE
HARNESS
2 WIRE
TIES
ENGINE STARTER
HARNESS
WIRE TIE
QB20937BH
CAUTION
LABEL
QB20938AH
74. Attach the caution label to the hood in the area shown.
75. Check that all wire harnesses are routed properly and all connectors are plugged in.
76. Check the overlap between the headliner and the driver’s A-pillar trim. Refer to the Service Manual. If necessary, adjust the overlap.
77. Install all removed parts.
78. Connect the negative cable to the battery.
79. Press and hold the audio unit power button for two seconds to restore the audio and navi (if equipped) system functions.
80. Set the clock.
81. Perform the “REMOTE ENGINE STARTER
REGISTRATION” and the “FUNCTION CHECK”.
24 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
REMOTE ENGINE STARTER REGISTRATION
1.
Acquire the PCM Code from the Interactive Network.
CAR ICON
Select
“Honda Systems.”
QB40150AH
2.
Connect the HDS/MVCI tester to the OBD II data link connector, then turn the ignition switch to the on (II) position.
3.
Start the HDS, and click the car icon.
4.
Input the VIN and other required information into the
HDS, then click the check button.
CHECK BUTTON
QB32103AH
6.
Select R/C ENG STARTER and click the check button.
Select
“R/C ENG STARTER.”
CHECK BUTTON
QB32104AH
Input the VIN and other required information.
CHECK BUTTON
QB32102BH
5.
Select Honda Systems, then click the check button.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
25 of 29
7.
Select REGISTER REMOTE CONTROL ENGINE
STARTER UNIT, then click the check button.
Select
“REGISTER REMOTE
CONTROL ENGINE
STARTER UNIT.”
9.
Input the PCM-code, then click the check button.
NOTE: To ensure security, the PCM-code
(password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM-code acquisition and registration are different. The date of the HDS/MVCI tester should also be the same.
Input the PCM-Code.
CHECK BUTTON
QB32105BH
8.
The following message will display: Obtain PCM-
code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the
password. (USA) Click the check button.
“Obtain PCM-code” message.
CHECK BUTTON
QB32107BH
10. The following message will display: The registration
of the Remote Control Engine Starter Unit has
been completed. Turn the ignition switch off.
“The registration of the
Remote Control Engine
Starter Unit has been completed.”
CHECK BUTTON
QB32106AH
QB32108CH
26 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
11. The following message will display: Check that
engine can be started by the Transmitter. Click
the check button.
“Check that engine can be started by the Transmitter.”
CHECK BUTTON
QB32109CH
12. Perform the FUNCTION CHECK on page 28, then
disconnect the HDS/MVCI.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
27 of 29
FUNCTION CHECK
Operating Conditions
• The hood is closed
• The shift lever is in park
• Turn the ignition switch off and the key is outside the vehicle
• All doors and trunk lid closed and locked
Inspection
1.
Press the engine/command button on the transmitter and release, within 2 seconds, press the lock/start button on the transmitter.
The engine should start if all operating conditions are met.
Does the engine start?
Yes - Operation is normal.
No:
• Make sure all “Operating Conditions” are met.
• Check the engine starter harness connections.
• Connect the HDS/MVCI and check for an indicated failure.
(Refer to the appropriate Service Manual for details.)
2.
Press the engine/command button on the transmitter and release, within 2 seconds, press the unlock/stop button. The engine should stop.
Does the engine stop?
ENGINE START
OPERATION
RECEPTION
INDICATOR
CHECKING
INDICATOR
Yes - Operation is normal.
No - Check the engine starter harness connections.
ENGINE/
COMMAND
BUTTON
Blinking
ENGINE
RUNNING
INDICATOR
3.
After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
UNLOCK/
STOP
BUTTON
*1
REMAINING
IDLING TIME
NOTE: After each test the ignition key must be cycled, or the driver’s door must be opened and closed.
LOCK/
START
BUTTON
• Move the shift lever out of the P position.
IN-CAR
B127121H
TEMPERATURE
*1
•
• Unlock or open the doors or the trunk lid.
Open the hood.
*1 Only on vehicles equipped with the automatic climate control.
This indicator is displayed for some vehicles among them.
• Insert the key in the ignition.
• If the vehicle is equipped the keyless access system, press the engine start/stop button.
• Press on the brake pedal.
Does the engine stop after each of these tests?
Yes - Operation is normal.
No - Check the engine starter harness connections.
4.
Check that the power windows and the moonroof do not function, and the shift lever does not move to any position when the engine is started with the transmitter.
5.
If the vehicle is equipped with the keyless access system, check that the engine does not start under “Operating
Conditions” with the key left inside the vehicle.
6.
Start the engine again, press the engine/command button on the transmitter two times, and check the vehicle condition on the display.
7.
Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight.
28 of 29
AII04162-35 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.
8.
Press the unlock/stop button on the transmitter and verify that the doors unlock. Press the lock/start button, and verify that the doors lock.
For the vehicle equipped with the memory seat, make sure to shift the seat position of driver’s seat to “Driver 1” by unlock of transmitter.
9.
Check that the engine can start by the vehicle key and that the wiper and the headlight can be operated normally.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-35 (1606)
29 of 29

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remotely start and stop engine
- Install on Honda vehicles
- Use control unit to connect harness
- Register remote control engine starter with HDS/MVCI
- Antenna for remote control
- Step-by-step installation instructions
- Detailed parts list
- Safety precautions
- Function check instructions
- Troubleshooting tips