LASER-UK Show Selector LASER-UK Rainbow Vision LASER SHOW SYSTEM Instructions Button 1 Press For Sound Control Buttons 1-8 Individual Shows With Button 1 Lifted Button 10 Press For Blackout DMX Address Chart This chart lists the DMX dipswitch setting for DMX address 1 through 511. Follow the instructions below to configure fixture dipswitches with you desired DMX address. DMX Address Quick Reference Chart DipSwitch Position DipSwitch Position DMX Address Page 9 General instructions Notes: 1. DMX console can not be used in Master-Slave operation (Sound Active or AUTO mode ). 2. There should be only one master unit in Master-Slave operation. Unpacking: Thank you for purchasing this product. Please read user guide for safety and operations inf- Troubleshooting ormation before using the product. Keep this manual for future reference. This product can create perfect laser programs and effects since it has passed a series of strictly tests before 1. In Stand-Alone operation, if the power supply indicator is light up and sound active indic- delivery. Please check the attachments listed on the page after opening the carton. In the ator isn't light up, but the laser is shut off doesn't work, Please check if unit has been set up event of carton damage or attachment missing in transit, please contact your dealer or our in slave mode, then set up in master mode. after sales service department. 2. In Master-Slave operation, slave unit don't function, please check as below. A. Make sure to there's only one master in the chain, and the others are set in slave mode. Attachments: B. Make sure to control the unit without DMX console controlling. 1. Laser Light: 1PCS C. Make sure to take a good quality power cable and connection. 2. Power Cable: 1PCS 3. In DMX mode operation, the laser is OFF and the DMX signal indicator is unlighted, pl- 3. User Guide: 1PCS ease check as below. Make sure to set up the DMX mode, make sure to have a good connection. 4. In DMX operation, the unit can’t be controlled by the DMX console, but the DMX signal Notice: indicator is flashing, please make sure the DMX console and unit have the same channel. 1. Do not exposure the human eye direct to laser beam. 5. If the unit is fail, please turn off the unit, then turn on again after 5 minutes. 2. Do not turn on and off the unit frequently. 3. Before using this unit make sure the power supply is ground. After trying the above solution you still have a problem, please contact your dealer or our 4. This unit is intended for indoor use only and should be prevented form water, moisture company for service. and shake. The working temperature of this unit is 18 ～30℃, do not use this continuously over 4 hours, otherwise it shortens the lifetime of the unit. 5. Use cleaning tissue to remove the dust absorbed on the external lenses periodically to optimize light output. 6. Do not remove or break the warranty label, otherwise it void the warranty. 7. Always replace with the exact same type fuse, replacement with anything other than the specified fuse can cause fire or electric shock and damage your unit, and will void your manufactures warranty. DANGER LASER RADIATION AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT Page 8 Page 1 ! Technical Specification 5. The units will react to the low frequencies of music via the internal microphone. Adjust the audio sensitivity knob on the back of the master unit to make the unit more or less se- 1. Voltage: □AC220V/ □110V, 50HZ/60HZ, Fuse 2A/250V nsitive in sound active.The panel has LED indicating for sound active. 2. Rated Power: 80W 3. Scanner: High-speed optical scanner, big angle scanning 4. Laser: 650nm wavelength 532nm wavelength 405nm wavelength POWER 200mW 50mW 1：MASTER:SOUND/AUTO POWER ………… 2：SLAVE 200mW Mixed white laser: Universal DMX Operation (DMX mode) 450mW 5. Working Modes: Sound Active, AUTO-Beam, AUTO-Animation, DMX512 (12 CH), This mode allows you to use universal DMX-512 console to operate. Master/Slave 1. Install the units in a suitable position (laying or appending). 6. Graphics & Effects: 128 beam show and animated graphics show patterns 2. Use standard XLR microphone cable chain your units together via the XLR connector 7. Interface: 3 pins XLR jack for DMX or Maser-Slave linking on the rear of the units. For longer cable runs we suggest a terminator at the last fixture. 3. Assign a DMX address to each the unit using dipswitches, see the "DMX Address Quick 8. Size: L*W*H=370*320*130mm Reference Char". 9. Weight: 6KG 4. Turn on the all units' power, the units begins reset, then the unit begins working. 5. Use DMX console to control your units. Features 1. Full-color animation laser with high-speed optical scanner to create animated graphics, POWER 128 beam show and graphics show patterns, and with the function of unique blanking, frequently flashing, rotating, moving, rotation, split, zoom, drawing, speed and color etc. DMX Signal 1：DMX MODE 2：DMX MODE 2. Includes six working modes as DMX512, Sound Active, AUTO-Animation, AUTOBeam, Master-Slave and Show Selector Control 3. The unit has eleven channels to control in DMX mode. The unit has BLACK OUT function. The uint will shut off if no DMX512 signal. 4. Multi Show choices when used with the optional Show Selector device. 5. Design according to security and good performance, safer to human and environment. Master/Slave mode, DMX512 mode, will shut off laser automatically without trigger signal. Page 2 POWER ………… Page 7 Front/Rear Panel One loop address=1, two loop address=17, three loop address=33, four loop address=49 Loop Address Binary Dipswitches 1 1 100000000 ＃1 (＃1 switch is ON, the others are OFF) 3 17 100010000 ＃1+#5 (＃1 and #5 switches are ON) 3 33 100001000 ＃1+#6 (＃1 and #6 switches are ON) 4 49 100011000 ＃1+#5+#6 (＃1,5,6 switches are ON) The dipswitches setting for DMX address see the " DMX Address Quick Reference Chart ". Operation Stand-Alone Operation (Sound Active, AUTO mode) Front Panel Figure 1. Laser aperture 2. Sound active microphone 3. Sound active indicator:Blue 4. Power indicator:Red The mode allows a single unit to react to the beat of the music in the master mode. 9 1. Install the units in a suitable position (laying or appending). 6 3 5 4 3 2 2. Set dipswitch to select Sound Active or AUTO mode. 3. Turn on the unit power, the unit begins reset, then the unit begins working. 4. The unit will react to the low frequencies of music via the internal microphone. Adjust the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in sound active.The panel has LED indicating for sound active. 8 7 1 Rear Panel Figure POWER 1: Master: Sound/AUTO 1. Power jack 2. Power switch 5. Audio sensitivity knob 3. Cooling fan 6. Function reference chart 4. Pattern size knob 7. DMX or linking jack 8. Show Selector interface with DB25 jack Master-Slave Operation 9. Function of built-in program setting dipswitches This mode will allow you to link up to many units together without controller. Function & Setting 1. Install the units in a suitable position (laying or appending). 2. Choose a unit to function as Master mode, set dipswitch to select Sound Active or AUTO mode. The others must be set to Slave mode, set dipswitch to select Slave mode. Sound Active 3. Use standard XLR microphone cable chain your units together via the XLR connector The change of the laser pattern is controlled by sound, that is, the rhythm of the sound on the rear of the units. For longer cable runs we suggest a terminator at the last fixture. control the effect of the changing laser pattern. 4. Turn on the all units' power, the units begins reset, then the unit begins working. The AUTO slave units will react the same as the master unit. Auto cycles the built-in programs without being controlled externally. It has no laser OFF. Page 6 Page 3 DMX Control The system only accepts the DMX512 signal of international standard to control the system. DMX Control Parameter Chart Channel Function Value CH1 Mode Channel Function CH12 Drawing Value Description 0~127 Auto drawing mode 1 128~255 Auto drawing mode 2 Description 0～49 Sound Active mode Function setting 50～99 Auto-Beam mode Auto Animation has 4 different programs. Choose switches 1&5, 1&6, 1&7 or 1&8 100～149 Auto-Animation mode 150～199 Manual mode to Auto run 200～255 Manual mode to Sound Active run 0＝OFF Cosed~white~red~yellow~green~blue~ CH2 CH3 Dimmer 0～255 Pattern Select 0～255 0～127 CH4 Moving-Y Moving-X color~fixed color 0 0 0 X X X X X X 0 SOUND ACTIVE 128 pattrens 1 0 0 X X X X X X 0 AUTO-BEAM Manual to up to down moving 1 0 0 X 1 1 1 1 X 0 AUTO-ANIMATION 0 0 1 X X X X X X 0 SLAVE MODE SET DMX ADDRESS Manual to left to right moving Rolling-X CH7 Rolling-Y Manual rolling 0～127 128～255 Auto rolling CH9 Rotation Zoom(+/-) Built-In Program Function Chart DMX address calculation For DMX mode, DMX address from #1 to 9# dipswitches must be set, the address is set from 1 to 511. Each dipswitch represents a binary value. Manual rolling Dipswitch Value Dipswitch Value ＃1 1 ＃6 32 ＃2 2 ＃7 64 128～191 Auto clockwise rotation ＃3 4 ＃8 128 192～255 Auto counter clockwise rotation ＃4 8 ＃9 256 ＃5 16 ＃10 0～127 128～255 Auto rolling Manual rotation 0～127 CH8 1 DMX MODE 128～191 Auto to right moving 192～255 Auto to left moving CH6 FUNCTION #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 192～255 Auto to up moving CH5 X=OFF or ON ~random seven-color~moving seven- 128～191 Auto to down moving 0～127 1=ON DIPSWITCH CHART purple~fixed color~~random single color 0～85 Auto zoom(+) 86～170 Auto zoom(-) 171～255 Manual zoom(+/-) CH10 Pattern Size 0～255 0 is Moderate, 1 is small, 255 is big CH11 Display Dot 0～255 0 is display dot, 255 is best brightness Page 4 DMX, Set to "1" One unit has 12 channels for DMX control, so each unit must be assigns 12 channels at least We may assign 16 channels for one unit, then DMX address = 16*N + 1, N=0, 1, 2, 3 …… Example Page 5
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021