advertisement
ProSYS Plus
Quick User Guide
Full (“Away”) Arming
Quick mode:
High Security mode: Code
Quick mode: .
High security mode:
Proximity tag
code or use
Full Arm all: Security
to apply to all partitions, or slide a specific partition to the right under
.
Quick mode: .
High Security mode:
Partial (“Stay”) Arming
code
Quick mode:
High Security mode: Code
Partial Arm all: Security press
Press
Quick mode:
High security mode:
Proximity tag
code or use
to apply to all partitions, or slide a specific partition to the left under
Quick mode: .
High security mode:
Partition & Group Arming
code
Full partition arming:
Code select All or specific partition number/s
Partial partition arming:
Code select All or specific partition number/s
Group Arming: Press group letter
Press or large rounded button
(installer-defined)
Note: Supports up to 3 partitions. Does not support Group arming.
Full partition arming:
Quick mode: Partition number
High Security mode: Partition number
code or use Proximity tag
Partial partition arming:
Quick mode: Partition number
High Security mode: Partition number
code or use Proximity tag
System Disarming
Code
code or use Proximity tag
Disarm all: Security
press Disarm
code to disarm all partitions, or slide a specific partition to the center under enter code
Quick mode: .
High security mode:
Partition & Group Disarming
code
Partition disarming: Code
select All or specific partition number(s)
Group disarming:
Duress Disarming
Duress code
Note: Panel is silent (no alarm siren)
Bypassing & Un-bypassing Zones
Disarm all: Press
Partition disarming: Partition number
code
duress code
Note: Panel is silent (no alarm siren)
code, scroll to Activities menu, Bypass, Zones,
scroll to select a bypass option, .
Viewing System Troubles
code, scroll to View menu, Trouble , scroll to view troubles
Viewing Last Alarm / Event Log
code, scroll to Event Log , scroll to view events
Viewing System Status
for 2 seconds
Quick mode: for 2 seconds
High Security mode: for 2 seconds
code or use Proximity tag
Quick mode: for 2 seconds
High Security mode: for 2 seconds code
01/2016 Page 2 5IN2370
Activating Output
code, scroll to
Activities menu, enter Utility
Output number, .
Note: Must be installer-defined
Quick mode: Press button (1—3) for 2 seconds
High security mode: Press button (1—3) for 2 seconds code or use Proximity tag.
Note: Must be installer-defined
Quick mode: Press button (1—3) for 2 seconds
High security mode: Press button (1—3) for 2 seconds enter code.
Note: Must be installer-defined
Activating a Panic Alarm
Press and for at least 2 seconds.
together Press seconds
and together for 2
Press and
Activating a Fire Alarm
together for 2 seconds.
Press and together for at least 2 seconds.
Activating an Auxiliary Emergency Alarm
Press + together for 2 seconds
Press and together for at least 2 seconds.
Press + together for 2 seconds
SMS Commands
NOTES: Command words are not case sensitive. A separator between command words may be used (or not). To receive an acknowledgement reply, add RP to the end of an SMS command.
Full Arm: code + A (Example: 1234A)
Home Arm: code + H
Get system status: code + ST
Bypass Zone: code + B + zone number
Group Arm: code + G + select group A--D
Un-bypass Zone: code + UB + zone number
Full Disarm: code + D View last alarm : code + AL
Partition Full Arm: code + A + partition number
Change FM number: code + FMPHONE +
FM serial number + NEW + new phone number
Partition Home Arm: code + H + partition number
Activate Output: code + UOON + UO number
Deactivate Output: code + UOOFF + UO number
Partition Disarm: code + D + partition number Get SIM credit level: code + CR
01/2016 Page 3 5IN2370
LED Indicators – Elegant Keypad
Power LED
Ready LED
On: Power OK.
Off: No power
Rapid flash: System trouble.
Slow flash: System is programming
On: Ready to arm
Off: Not ready to arm
Slow flash: Ready to arm while entry/exit zone is open
Arm LED
On: System in fully armed mode
Off: System disarmed
Rapid flash: Alarm
Slow flash: System in Exit Delay
Partial Arm / Bypass LED
On: System in partially-armed or zone-bypassed mode
Off: No bypassed zones
Tamper LED
On: Tamper alarm
Off: No tamper alarm
Fire LED:
On: Fire alarm
Off: No fire alarm
Flash: Fire circuit trouble
LED Indicators – 2-Way Remote Control Defining User Codes – Elegant Keypad
Operation
Send Receive
Status
1. Grand master code (default = 1234) ,
Full Arm command
Green
Partial Arm Green
*
Red
Orange
2. to scroll to Codes/Tags press twice.
Disarm Green Green 3. to scroll to the user (index number) for
*
If the LED changes to orange, it indicates a low battery condition. defining press twice.
4. Enter (or re-enter) a 4—6 digit code, ; the system beeps and ACCEPTED displays
Registering to the RISCO Cloud
1 . After the RISCO Cloud has been enabled by your system installer, go to www.riscocloud.com
2 . Fill in your first and last name.
3 . Enter your e-mail address as the Login Name (required for 1st-time activation).
4 . Define password (minimum of 6 characters and at least one digit), and then confirm.
5 . Enter the 15 digits Panel ID as it appears as printed on the postcard packaged with the main panel. You can also view it on the keypad (see the ProSYS Plus User Manual).
6 . Complete registration form, and then press Register.
7 . Open the e-mail received at the email account you had defined as the Login Name in step 3, and then click the link to activate your registration to the Cloud.
Logging in to the RISCO Cloud / Accessing the Web User Application
1 . Go to www.riscocloud.com
2 . Enter your user name and password (as defined during the registration process).
3 . Enter the system PIN code (user code).
4 . Click Enter.
iRISCO Smartphone App
Download the iRISCO Smartphone app from the Apple App store or the Android Play Store.
For additional information see the ProSYS Plus User Manual, available on our website: www.riscogroup.com
© RISCO Group 2016. All rights reserved.
01/2016 Page 4 5IN2370
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project