Undercounter Dishwasher

®
Undercounter Dishwasher
PRODUCT MODEL NUMBERS
DU400SWK
DU600PWK
DU620PWK
DU800SWK
DU810SWK
DU810SWL
DU811SWK
DU811SWL
DU840SWK
DU840SWL
DU850SWK
DU850SWL
DU890SWK
DU890SWL
DU900PWK
DU909PWK
DU910PWK
DU911PWK
OVERALL DIMENSIONS
DU915PWK
DU920PWK
DU930PWK
DU940PWK
DU941PWK
DU943PWK
DU945PWK
DU948PWK
DU950PWK
DU951PWK
DU955PWK
DU960PNK
DU960PWK
DU963PWK
DUL100PK
DUL200PK
GU970PNL
23-7/8" (60.6 cm)
24" (61 cm)*
33-7/8"
(86 cm) min.
* to front of
door frame
Electrical: 120-volt, 60-Hz, AC-only, 15- or
20-amp. electrical supply. Use copper wire only. A time-delay
fuse or circuit breaker and separate circuit is recommended.
Water: A hot water line with 20-120 psi (138-862 kPa) water
pressure. Water temperature must be 120°F (49°C) at
dishwasher. Use 3/8" O.D. copper tubing with compression
fitting or flexible stainless steel braided fill line (1/2" minimum
plastic tubing is optional but not recommended). Use a 90°
elbow with 3/8" N.P.T. external pipe threads on one end to
connect to water inlet valve. Do not solder within 6" (15.2 cm)
from water inlet valve.
Drain: Use the new drain hose supplied with your
dishwasher. If this is not suitable, use a new drain hose with a
maximum length of 12 feet (3.7 m) that meets all current
AHAM/IAPMO test standards, is resistant to heat and
detergent, and fits the drain connector of the dishwasher.
Must have a high drain loop 20 inches (50.8 cm) above the
subfloor or floor. Connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20 inches
(50.8 cm) minimum above the floor. An air gap must be used
if the drain hose is connected to house plumbing lower than
20 inches (50.8 cm) above subfloor or floor. Use 1/2"
minimum I.D. drain line fittings.
Corner installation: Allow 2" (5,1 cm) minimum between
corner wall and dishwasher opening.
Grommet is required for electrical cable or power supply cord
hole cut in a metal cabinet.
20-3/4" (52.7 cm)
CABINET OPENING DIMENSIONS
24" (61 cm)**
* Measured from the lowest point
on the underside of countertop.
** Minimum, measured from
narrowest point of opening.
34" (86.4 cm) min.*
24" (61 cm)
6"(15.2 cm)
6"(15.2 cm)
4" (10.2 cm)
4"
(10.2 cm)
4" (10.2 cm)
10"
(25.4 cm)
2-1/2"
(6.4 cm)
2-1/2"
(6.4 cm)
Do NOT install dishwasher over carpeted floor.
Accepts custom door panels:
DU800SWKU, DU810SWKU, DU811SWKU
Accepts custom door and access panels:
DU840SWKU, DU890SWKU,
Other models require trim kits in order to add custom panels.
The panels must be made to the dimensions supplied with the
trim kit.
2"
(5.1 cm)
5" (12.7 cm)
5" (12.7 cm)
Water line should enter through the
left side of opening in shaded areas.
Minimum 1/2" (12,7 mm) hole.
2"
(5.1 cm)
Power supply line should enter through the right side of opening in
shaded areas.
Power supply line hole-direct wired: 3/4" (1.9 cm)
Power supply line hole-with plug: 1-1/2" (3.8 cm)
Drain hose should enter through cabinet in shaded areas.
Drain hose size: 1-1/2" (3.8 cm)
CUSTOM FRONT PANEL DIMENSIONS
7/32"
(5.6 mm)
door panel (front view)
Note: Access panel is wider than door panel.
door panel
(side view)
18 21/32"
(47.4 cm)
maximum weight is
8 lbs (3.6 kg). Heavy
duty door springs
required for door
panels weighing more
than 4 lbs (1.8 kg).
4 7/16"
11.3 cm
(top view)
Cut door panel to clear access
panel when door is in open
position .
side view
23 5/16" (59.2 cm)
3/8"
(9.5 mm)
1"
(25.4 mm)
access panel (front view)
All edges routed to 7/32" (5.6 mm) thickness.
Note: This panel is wider than the door panel.
door
opened
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
door
pivot
7/32" (5.6 mm) thick
7/32"
(5.6 mm)
22 31/32"
(58.3 cm)
door
closed
access panel frame
access
panel
1/4"
(6.4 mm) min.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 3385181
07-23-03