Marine Products

Marine Products
Marine Products
Section V
Marine Products
Index
Category
30A, 125V AC
Telephone and Cable TV
50A, 125V AC
50A, 125/250V AC
100A, 125/250V AC
100A, 3ØY 120/208V AC
20A, 125V AC
Ship-to-Shore Selection Guide
Adapters
Internationally Rated Devices
15A, 125V AC
Ground Fault Devices
Inside the Boat
12V Switches
28V DC
Boatyard Accessory Items
Electrical Standards
Description
Ship-to-Shore Devices
Ship-to-Shore Devices
Ship-to-Shore Twist Lock® Devices
Ship-to-Shore Twist Lock Devices
Ship-to-Shore Pin and Sleeve Devices
Ship-to-Shore Pin and Sleeve Devices
Twist-Lock and Straight Blade Devices
YQ Adapters
Adapter Selection Guide
Molded Straight Adapters
Molded Y Adapters
16A, 32A and 63A, 240V AC
16A, 32A, 230V AC
Twist-Lock and Straight Blade Devices
Portable Ground Fault Circuit Interrupters,
Testers and GFCI Receptacles
Receptacles
Switches and Weatherproof Switch Plates
Wall Plates
Communication Frames and Connectors
Toggle and Rocker Switches, DC Rated
DC Rated System for 12, 24 and 32 Volt,
DC Rated Electric Fishing Reel Systems
Cord Connectors
Outlet Box Hoods
Lighting
Weatherproof Boxes and Covers
Weatherproof Plates
Codes and Specifications
Page Number
V-2–7
V-8–9
V-10–11
V-12–13
V-14–17
V-14–15,18–19
V-20–21
V-22–23
V-24
V-25
V-26
V-27
V-28
V-29
V-30–31
V-32–33
V-34
V-35
V-36
V-37
V-38
V-39
V-40
V-40
V-41
V-42
V-43
V-44
?????
Index
Dimensions in Inches (mm)
www.hubbell-wiring.com
Marine Products
Marine Products
30 Ampere, 125V AC Cable Set
Features and Benefits
UL Listed.
Available in 25', 35' and 50' lengths.
Jute fillers inside jacket for maximum cable flexibility.
Hubbell cable coils neater, lighter, lays flatter.
Molded flexneck adds life to cable set by preventing
right-angle cable damage and pullout.
Strain relief bull ring protects against stress and strain
on the conductors caused by boat movement,
crew traffic and rough handling.
Exclusive copper crimp barrel termination
provides protection against internal
overheating and burnout compared to
brass crimps. These copper crimps are
the same type used by power companies.
The result: tighter connections,
better conductivity and longer life.
Molded design totally encased
in solid PVC material,
for superior waterproofing
and durability.
Locking ring assures proper alignment of connector to inlet
for complete contact and waterproofing.
Prevents accidental disengagement.
Line-up notches to indicate:
Locked - Unlocked.
Arrow indicating lock position.
Features and Benefits
Arrow with ground symbol allows
lining up with ground of receptacle.
New improved styling.
Arrow indicating unlock position.
V-2
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
30 Ampere, 125V AC
2 Pole 3 Wire
Ship-to-Shore Devices
Our 30A, 125V cable set is
packed with details end to end
that make a high performance
difference. Completely factory
pre-wired with molded-on
devices. Designed to coil easily
and lie flat.
IP56
SUITABILITY
(Boatside)
W
G
30A 125V
30A 125V AC Shore Power Cable Set
YC310250
Dimensions in Inches (mm)
www.hubbell-wiring.com
Catalog Numbers
HBL61CM08
HBL61CM05
HBL61CM03
HBL61CM08W
HBL61CM03W
YC310250
WC310280
V-3
Cable Sets and Bulk Cable
HBL61CM08
Description
50’ yellow vinyl jacketed shore power cable set. #10 AWG is
factory pre-wired with molded-on devices. Connector end has
non-metallic threaded sealing ring which makes inlet/connector
interface watertight.
Same as #HBL61CM08 except 35’ in length.
Same as #HBL61CM08 except 25’ in length.
50’ white shore power cable set.
25’ white shore power cable set.
Three conductor, #10 AWG type STW, yellow PVC jacketed
portable cord with jute fillers for added flexibility. Ideal for making
cable sets, extension cord, and adapters that will not mark boat’s
deck. 250’ lengths only.
Three conductor, #10 AWG type STW, white PVC jacketed
portable cord with jute fillers for added flexibility. Ideal for making
cable sets, extension cord, and adapters that will not mark boat’s
deck. 280’ lengths only.
Marine Products
Marine Products
Stylized Line of Shore Power Inlets
Contemporary Styling — Hubbell Quality
30 Amp Interior
Contacts are nickel
plated brass for
corrosion resistance.
New easy-to-wire interior
is transparent for quick,
visual inspection of
terminations.
Fits most mounting
patterns.
Includes #SR3050
protective rear enclosure
cap attaches to contact
carrier with 3 screws.
50 Amp Interior
Notched contact carrier
enables wiring of
interior while in place.
Pressure screw
terminals for secure
terminations - clearly
marked for easy
identification.
Stylized Shore Power Inlets
Thermoset contact
carrier is arcing and
heat resistant.
Optional #SR3050
protective rear enclosure
cap attaches to contact
carrier with 3 screws.
Fits most mounting
patterns.
Take advantage of these contemporary shore power inlets – in either
rugged thermoplastic or corrosion resistant stainless steel – to add the
finishing touch to a boat going into production or to modernize a boat
that’s seen many seasons of use. Both the gleaming, white Centrex®
non-metallic models and the brushed, type 316 stainless steel models
offer the same features. For starters, you’ll be glad to hear that these
Hubbell shore power inlets install as easy as 1-2-3 and match most
mounting patterns available. Then you’ll discover that they have a lot of
built-in extras like a friction-tight cover that automatically holds the
cover open while inserting the cable set. Plus, you’ll find inside a
genuine Hubbell wiring device with all of the quality characteristics that
have made Hubbell the marine electrical products leader. What’s more,
you can complement these stylish devices with phone and TV inlets for
a complete family.
Stylized Watertight Stainless Steel Shore Power Inlet Series
„ #316 stainless steel for corrosion resistance.
„ Does not require screwing down of cover for water resistance.
„ Fully watertight when locked closed to comply with ABYC recommendations.
Stylized Weatherproof Non-Metallic Shore Power Inlet Series
„ Centrex non-metallic cover is specifically designed for outdoor use with
outstanding UV resistance, impact resistance and weatherability.
„ Meets ABYC recommendations for inlets installed in weatherproof areas.
Centrex ® is a registered trademark of Monsanto; Rynite ® is a registered trademark of E. I. DuPont.
V-4
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
30 Ampere, 125V AC
2 Pole 3 Wire
Ship-to-Shore Devices
W
IP56
SUITABILITY
G
Inlets Only.
30A 125V
30A 125V AC Ship-to-Shore Devices
NEMA L5-30R
HBL303NM
HBL303SSBL
2P 3W, 30A, 125V TWIST-LOCK® Devices
Description
Catalog Numbers
Stylized UV resistant non-metallic shore power inlet has white
HBL303NM
Centrex cover which makes unit weatherproof when completely
closed. Interior has easy-to-wire terminations and is transparent for
quick and easy visual inspection. Mounting holes are 23 /8” (60.3)
on centers and match existing mounting patterns. Mounting screws
and gasket included. Protective rear enclosure/strain relief also
included.
Stylized type 316 stainless steel shore power inlet has easy to use HBL303SSBL
push-button latch that makes unit watertight when fully engaged.
Interior has easy-to-wire terminations and is transparent for quick
and easy visual inspection. Mounting holes are 23 /8” (60.3) on
centers and match existing mounting patterns. Mounting screws
and gasket included. Protective rear enclosure/strain relief also
included.
Traditional, stainless steel shore power inlet has new easy-to-wire HBL303SS
terminations. Interior is transparent for quick and easy visual
inspection. Interior is shielded from the elements by a gasketed,
self-closing cover, watertight when cover is screwed in place.
Mounting holes are 23 /8” (60.3) on centers. Mounting screws and
gasket included. Protective rear enclosure/strain relief also included.
Traditional stainless steel inlet housing; blank for attaching a
HBLCBISS*
circuit breaker (not included). Mounting hardware for Carling
series breakers included.
Stylized non-metallic inlet housing; blank for attaching a circuit
HBLCBINM
breaker (not included). Mounting hardware for Carling series
breakers included.
Protective rear cover. Fits all 30A shore power inlets.
SR3050**
Secures to back of inlets with 3 screws which are provided.
Replacement interior for #HBL303SS and #60CM61
HBL303INT*
shore power inlets.
Nickel plated brass adapter plate for mounting traditional round
HBL60CM75*
stainless steel shore power inlets to FS/FD box.
Traditional stainless steel power outlet has gasketed,
HBL303SSO
self-closing cover, watertight when cover is screwed in place.
Mounting holes are 2 3 /8” (60.3) on centers. Mounting screws
and gasket included.
Notes: *Not shown.
** Not UL/CSA
HBL303SS
30A 125V AC Traditional Stainless Steel Inlets
Base and cover are #316
type stainless steel for strength
and corrosion resistance.
Self-closing cover assures
the interior is shielded from
the elements when
the inlet is not in use.
Neoprene gasket on
underside of cover.
For sealing when the
cover is closed.
Contact blades are
nickel plated brass
for corrosion
resistance.
Threaded base for making a
watertight seal. When in
use, it mates to the threaded
ring of the weatherproof
cover on the connector
body. When not in use, it
mates to the threaded cover.
Dimensions in Inches (mm)
New, easy-to-wire interior is transparent for
quick, visual inspection
of terminations and
high-heat resistance.
HBLCBINM
Contacts are nickel
plated brass for
corrosion resistance.
New easy-to-wire interior
is transparent for quick,
visual inspection of
terminations.
#SR3050 protective
rear enclosure cap
attaches to contact
carrier with 3 screws.
HBL303SS0
Three screws “lock-in” the
interior once it is in place.
www.hubbell-wiring.com
V-5
Marine Products
Marine Products
30 Ampere, 125V AC
2 Pole 3 Wire
Ship-to-Shore Devices
W
G
Plugs and connectors only.
30A 125V
30A 125V AC Ship-to-Shore Devices
HBL26CM10
HBL26CM11
2P 3W, 30A, 125V TWIST-LOCK® Devices
HBL60CM31
HBL60CM31W
HBL26CM13
HBL60CM33
HBL60CM33W
NEMA L5-30R
Description
Yellow single receptacle has Rynite® body and abuse resistant
nylon face. IP20 SUITABILITY.
Yellow Insulgrip® plug has rugged nylon housing and cord grip
with range of .360” to .930” (9-24) that utilizes a unique offset
jaws arrangement to provide secure strain relief. IP20 SUITABILITY.
Yellow Seal-Tite® cover for weatherproofing #HBL26CM11 or
#HBL23CM11 plugs. IP55 SUITABILITY. Note: Fits Insulgrip®
devices only.
White Seal-Tite® cover for weatherproofing #HBL26CM11
or #HBL23CM11 plugs. IP55 SUITABILITY. Note: Fits Insulgrip®
devices only.
Yellow Insulgrip® connector body has rugged nylon housing and
cord grip with range of .360” to .930” (9-24) that utilizes a unique
offset jaws arrangement to provide secure strain relief.
Yellow Seal-Tite® cover for weatherproofing #HBL26CM13 or
#HBL23CM13 connector bodies when used with shore power
inlets. Threaded sealing ring makes connection watertight. Also
for weatherproofing #HBL26CM11 plug when used with
#HBL303SSO power outlet. IP56 SUITABILITY. Note: Fits
Insulgrip® devices only.
White Seal-Tite® cover for weatherproofing #HBL26CM13 or
#HBL23CM13 connector body when used with shore power
inlets. Threaded sealing ring makes connection watertight.
Also for weatherproofing #HBL26CM11 plug when used with
#HBL303SSO power outlet. IP56 SUITABILITY. Note: Fits
Insulgrip® devices only.
Yellow Seal-Tite® cover for weatherproofing #HBL26CM13 or
#HBL23CM13 connector bodies when used on extension cords
or adapters. IP55 SUITABILITY. Note: Fits Insulgrip® devices only.
Yellow polycarbonate spring-loaded lift cover plate for weatherproofing old style #26CM10 receptacle. Meets the most stringent
requirements of UL’s three listing categories for weatherproof
plates. Stainless steel screws and neoprene gasket included for
mounting to FS/FD type weatherproof boxes.
IP44 SUITABILITY.
Same as #HBL74CM24WO except gray in color.
IP44 SUITABILITY.
Yellow polycarbonate spring-loaded lift cover plate for weatherproofing #HBL26CM10 receptacle. Meets the most stringent
requirements of UL’s three listing categories for weatherproof
plates. Stainless steel screws and neoprene gasket included for
mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY.
Same as HBL74CM25WOA except white in color
Same as #HBL74CM25WOA except gray in color.
IP44 SUITABILITY.
Stainless steel wall plate for old #23CM10 or #26CM10.
Stainless steel wall plate for new #HBL23CM10 or #HBL26CM10.
Notes: *Not shown.
**See page V-43 for photo.
+ Boots are not UL listable.
Catalog Numbers
HBL26CM10
HBL26CM11
HBL60CM31+
HBL60CM31W*+
HBL26CM13
HBL60CM33+
HBL60CM33W*+
HBL60CM32+
HBL74CM24WO**
HBL7424WO**
HBL74CM25WOA**
HBL74CM25WOAW*
HBL7425WOA**
S725*
S720*
HBL60CM32
Rynite® is a registered trademark of E. I. Dupont.
V-6
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
30 Ampere, 125V AC
2 Pole 3 Wire
Ship-to-Shore Devices
W
G
Plugs and connectors only.
30A 125V
30A 125V AC Ship-to-Shore Devices
NEMA L5-30R
Description
Yellow Valise® plug has one-piece nylon housing and
assembles easily with two screws. Built-in cord grip
has range of .590”-.930” (15.0-23.6). IP20 SUITABILITY.
Black Valise® plug for use on bass boats with trolling motor.
One-piece nylon housing assembles easily with two screws.
Built-in cord grip has a range of .590”-.930” (15.0-23.6).
IP20 SUITABILITY.
Yellow vinyl Seal-Tite® cover for weatherproofing
#HBL23CM11V or #HBL26CM11V plugs. IP55 SUITABILITY.
Note: Fits Valise® devices only.
Yellow Valise® connector body has a one-piece nylon housing
and assembles easily with two screws. Built-in cord grip has
range of .590”-.930” (15.0-23.6). IP20 SUITABILITY.
Yellow vinyl Seal-Tite® cover for #HBL26CM13V connector
body when used with shore power inlets. Threaded sealing ring
makes connection watertight. IP56 SUITABILITY.
Note: Fits Valise® devices only.
Yellow vinyl Seal-Tite® cover for weatherproofing #HBL23CM13V
or #HBL26CM13V connector bodies when used on extension
cords or adapters. IP55 SUITABILITY. Fits Valise® devices only.
Replacement non-metallic sealing ring for 30A cable sets
and boots. Not UL listed.
Note: +Boots are not UL listable.
Catalog Numbers
HBL26CM11V
HBL26CM11V
HBL26CM11VB
HBL60CM31V+
HBL26CM13V
HBL26CM11VB
HBL60CM33V+
HBL60CM32V+
RPL30P
HBL60CM31V
2P 3W, 30A, 125V TWIST-LOCK® Devices
HBL26CM13V
RPL30P
Valise Plug
Two captive
stainless steel
assembly screws.
Nickel plated brass
contacts for corrosion
resistance.
Terminals provide a
superior electrical
connection by
“bundling” the
conductors when the
clamps are tightened.
Exclusive nylon webs are
provided to make wiring quick &
easy by joining the three sections
together during assembly.
Dimensions in Inches (mm)
Powerful cord grips resist
conductor slip and strain on
wiring terminals.
A unique system of special
locking lugs interlock the
blade holder and sides as
the plug is closed. These
load bearing lugs provide
strength and security and
keep the Valise intact.
HBL60CM33V
Wiring time is reduced.
Large easy to wire clamp
type terminals eliminate the
need to wrap conductors
around a screw.
Nylon body.
HBL60CM32V
www.hubbell-wiring.com
V-7
Marine Products
Marine Products
Telephone & Cable TV
Ship-to-Shore Devices
Telephone and Cable TV Ship-to-Shore Devices
HBLPHTVNM
HBLPHTVRI
Telephone and Cable TV Devices
HBLPHTVSS
Description
Stylized non-metallic inlet provides telephone and cable TV
connections in one unit. UV resistant white Centrex® cover makes
unit weatherproof when completely closed. Mounting holes are
23 /8” (60.3) on centers and match existing mounting patterns.
Mounting screws and gasket provided. IP56 SUITABILITY.
Stylized stainless steel (Type 316) inlet provides telephone and
cable TV connections in one unit. Easy to use push-button latch
makes unit watertight when fully engaged. Mounting holes are
23 /8” (60.3) on centers and match existing mounting patterns.
Mounting screws and gasket provided. IP56 SUITABILITY.
Traditional stainless steel inlet provides connections for telephone
and cable TV in one unit. Connections can be used individually or
together. Gasketed cover is self-closing so interior is shielded
from the elements when not in use. Watertight when cover is
screwed in place. Mounting holes are 23 /8” (60.3) on centers.
Mounting screws and gasket included. IP56 SUITABILITY.
Replacement int. for #PH6594TV and #HBLPHTVSS series inlets.
Factory pre-wired 50’ (15.2m) telephone cable set. Uses 3
conductor, #16 AWG type SJTO, yellow vinyl cord for marine
and recreational vehicle applications. IP55 SUITABILITY.
Same as #PH6599 except white. IP55 SUITABILITY.
Same as #PH6599 except 25’ (7.6m) in length. IP55 SUITABILITY.
Same as #PH6598 except white. IP55 SUITABILITY.
Three conductor, #16 AWG type SJTO, yellow PVC jacketed
portable cord with jute fillers for added flexibility. Ideal for making
cable sets, extension cords and adapters as it will not mark boat’s
deck. For use with telephone systems only and available
in 250’ (76.2m) lengths only.
Black locking type plug for telephone cable sets or adapters.
Black locking type connector body used on telephone cable sets
or adapters.
Yellow Seal-Tite® cover for weatherproofing #PH6624 connector
body on cable sets when connecting to an inlet and for weatherproofing #PH6625 plug. IP55 SUITABILITY.
Yellow Seal-Tite cover for weatherproofing #PH6624 connector
body when used on extension cords or adapters. IP55 SUITABILITY.
Note: *Not shown.
Catalog Numbers
HBLPHTVNM
HBLPHTVRI
HBLPHTVSS
CR16914*
PH6599
PH6599W
PH6598
PH6598W
PH6630*
PH6625
PH6624
PH7440
PH7499*
PH6625
PH6624
PH7440
V-8
PH6598
PH6599
PH6598W
PH6599W
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
Telephone & Cable TV
Ship-to-Shore Devices
IP55
SUITABILITY
Telephone and Cable TV Ship-to-Shore Devices
Description
Black polycarbonate combination telephone/TV outlet with
spring-loaded weatherproof lift cover. Can be wired for telephone
service only or for telephone and MATV/CATV services in one
FS/FD box in both marinas and RV parks. Can be padlocked to
prevent unauthorized use.
Black polycarbonate telephone outlet has gasketed, springloaded lift cover for weatherproofing. Designed for mounting to
FS/FD type weatherproof boxes (like #PH6619) in both marinas
and RV parks.
Black polycarbonate cable TV outlet has coax connector
and gasketed, spring-loaded lift cover for weatherproofing.
Designed for mounting to FS/FD type weatherproof
boxes (like #PH6619) in both marinas and RV parks.
Black polycarbonate telephone outlet has gasketed, springloaded lift cover for weatherproofing. Can be used to retrofit
old style telephone outlets of Pauluhn Manufacturing Company
(#2833 and #2843) in both marinas and RV parks.
Black non-metallic FS box with 3 /4” threaded hubs used for
mounting phone and TV outlets and #PH6595 recreational
vehicle inlet (see #PH6621 for mounting box on recreational
vehicle). Cord connector included for strain relief and to maintain
watertight integrity of box when cable is used. PVC adapter also
included for connection of PVC conduit to box.
Stainless steel bracket for mounting #PH6619 FS box to
recreational vehicles when used with #PH6595 inlet.
Black polycarbonate RV inlet for telephone connection only.
Has spring-loaded, gasketed weatherproof lift cover designed for
mounting to FS/FD type weatherproof boxes.
50’ (15.2m) yellow jacketed ship-to-shore TV cable set is the
industry standard 75 Ohm, RG59-U with male plugs on both ends.
Adapter included for a quick, slip-on connection to inlet on boat.
Same as #TV99 except white.
Same as #TV99 except 25’ (7.6m) in length.
Same as #TV98 except white.
Note: *Not shown.
Catalog Numbers
PH6597TV
PH6597TV
PH6597
TV97
PH6596
PH6597
PH6619
PH6621*
PH6595
TV97
TV99
TV99W
TV98
TV98W
Telephone and Cable TV Devices
PH6596
PH6619
TV98
TV99
TV98W
TV99W
Dimensions in Inches (mm)
PH6595
www.hubbell-wiring.com
V-9
Marine Products
Marine Products
50 Ampere, 125V AC
2 Pole 3 Wire
Ship-to-Shore Devices
W
Inlets and connectors o
G
50A 125V
50A 125V AC Ship-to-Shore Devices
HBL503NM
HBL503RI
2P 3W, 50A, 125V TWIST-LOCK® Devices
HBL503SS
HBL63CM60
Description
Catalog Numbers
Stylized non-metallic shore power inlet has UV resistant white
HBL503NM
Centrex cover which makes unit weatherproof when completely
closed. Interior has easy to wire terminals. Mounting holes are
23 /8” (60.3) on centers and match existing mounting patterns.
Mounting screws and gasket included. IP56 SUITABILITY.
Stylized type 316 stainless steel shore power inlet has easy to
HBL503RI
use push-button latch that makes unit watertight when fully
engaged. Interior has easy to wire terminals. Mounting holes are
23 /8” (60.3) on centers and match existing mounting patterns.
Mounting screws and gasket included. IP56 SUITABILITY.
Traditional stainless steel shore power inlet has gasketed, selfHBL503SS
closing cover so interior is shielded from the elements when not
in use. Watertight when cover is securely fastened. Mounting
holes are 23 /8” (60.3) on centers, and rear portion has
2.171” (55.1) diameter. Mounting screws and gasket included.
IP56 SUITABILITY.
Protective rear cover. Fits all inlets except HBL503SS.
SR3050* **
Secures to back of inlets with 3 screws which are provided.
Replacement interior for #HBL503SS and #63CM72 shore power inlets.CR16277*
Nickel plated brass connector body has heat resistant thermoset
HBL63CM60
interior and combination metal and rubber cord grip provides
superior strain relief capability. Cord grip range is .437”-1.140”
(11.1-29.0). IP20 SUITABILITY.
Yellow Seal-Tite® cover for connector bodies when used with
HBL77CM15+
50A shore power inlets. Threaded sealing ring makes connections
watertight. IP56 SUITABILITY.
White Seal-Tite® cover for connector bodies when used with
HBL77CM15W*+
50A shore power inlets. Threaded sealing ring makes connections
watertight. IP56 SUITABILITY.
Nickel plated brass cord clamp assembly with clamp range of
HBL77CM67*
.437”-1.140” (11.1-29.0) provides strain relief for terminations on
shore power inlets.
Yellow Seal-Tite® cover for weatherproofing 50A connector
HBL77CM17+
bodies on extension cords or adapters. IP55 SUITABILITY.
Notes: *Not shown.
+ Boots are not UL listable.
** Not UL/CSA.
50A Traditional Stainless Steel Inlets
Base and cover are
#316 type stainless steel
for strength and
corrosion resistance.
HBL77CM15
Contact blades are
nickel plated brass
for corrosion
resistance.
Self-closing cover is friction tight to remain
open while engaging cable set and shields the
interior from the elements when the inlet is not
in use.
Neoprene gasket on
underside of cover for
sealing when the cover is
closed.
Three screws “lock-in” the
interior once it is in place.
Pressure screw terminals
for secure terminationsclearly marked for easy
identification.
Thermoset contact carrier is
arcing and heat resistant.
HBL77CM17
V-10
www.hubbell-wiring.com
Rear enclosure is nickel
plated for corrosion
resistance.
Threaded base for making a watertight seal. When in use, it
mates to the threaded ring of the watertight cover on the
connector body. When not in use, it mates to the threaded
cover.
Dimensions in Inches (mm)
Marine Products
Marine Products
50 Ampere, 125V AC
2 Pole 3 Wire
Ship-to-Shore Devices
W
Plugs and
receptacles only.
G
50A 125V
50A 125V AC Ship-to-Shore Devices
Catalog Numbers
HBL61CM53
HBL63CM61
HBL61CM53W
HBL61CM43
YC306250*
HBL77CM16
HBL63CM61
HBL77CM16+
HBL77CM16W*+
HBL63CM70
HBL77CM74WO
HBL7774WO
S750
HBL61CM53
HBL61CM53W
HBL61CM43
HBL63CM70
2P 3W, 50A, 125V TWIST-LOCK® Devices
Description
50’ (15.2m) yellow vinyl jacketed shore power cable set. #6 AWG
type STOW is completely factory pre-wired with molded-on devices.
Connector end has threaded metallic sealing ring to make inlet/
connector interface watertight. IP56 SUITABILITY (BOATSIDE).
Same as #HBL61CM53, except white.
IP56 SUITABILITY (BOATSIDE).
Same as #HBL61CM53, except 25’ (7.6m) in length.
IP56 SUITABILITY (BOATSIDE).
3 conductor, #6 AWG type STOW, yellow PVC jacketed portable
cord with jute fillers for added flexibility. Ideal for making cable sets,
extension cords, and adapters and will not mark boat’s deck.
250’ (75.2m) lengths only.
Nickel plated brass plug has heat resistant thermoset interior
and combination metal and rubber cord grip, provides superior
strain relief capability. Cord grip range is .437”-1.140” (11.1-29.0).
IP20 SUITABILITY.
Yellow Seal-Tite® cover for weatherproofing 50A plugs.
IP55 SUITABILITY.
White Seal-Tite® cover for weatherproofing 50A plugs.
IP55 SUITABILITY.
Single receptacle has a heat resistant thermoset base. IP20
Yellow Valox® lift cover plate for weatherproofing 50A
receptacles. Meets requirements of the most stringent of UL’s
three listing categories for weatherproof plates. Stainless steel
screws and a neoprene gasket included. For mounting to FS/FD
type weatherproof boxes. IP44 SUITABILITY.
Same as #HBL77CM74WO except gray in color. IP44 SUITABILITY.
Stainless steel wall plate for 50A receptacle.
Note: *Not shown.
+ Boots are not UL
listable.
HBL77CM74WO
50A Molded Cable Sets
Thermoset contact
carrier is arcing and
heat resistant.
Sealing lip to protect
plug/receptacle
connection from moisture.
Nickel plated brass
contact blades for
corrosion resistance.
Copper crimp
barrels for reliable
terminations.
Thermoset contact
carrier is arcing and
heat resistant.
Bull ring for
strain relief on
the terminals.
Bull ring for
strain relief on
the terminals.
Nickel plated
contacts for corrosion
resistance.
Molded-in flex
feature controls the
angle of cord entry
and keeps out
water.
Copper crimp
barrels for
reliable
terminations.
Nickel plated brass shell
for positive alignment of
keying and corrosion
resistance.
Nickel plated brass
shell for positive
alignment of keying
and corrosion
resistance.
Molded-in
flex feature
controls the
angle of
cord entry
and keeps
out water.
Metallic threaded
sealing ring to provide
a watertight seal
when mated with the
shore power inlet.
Valox® is a registered trademark of General Electric Company.
Dimensions in Inches (mm)
www.hubbell-wiring.com
S750
V-11
Marine Products
Marine Products
50 Ampere, 125/250V AC
3 Pole 4 Wire
Ship-to-Shore Devices
Y
X
Inlets and connectors o
W
G
50A 125/250V
50A 125/250V AC Ship-to-Shore Devices
HBL504NM
3P 4W, 50A, 125/250V TWIST-LOCK® Devices
HBL504RI
HBL504SS
HBL63CM64
Description
Stylized non-metallic shore power inlet has UV resistant white
Centrex cover which makes unit weatherproof when completely
closed. Interior is heat resistant thermoset material and has box
lug terminals. Mounting holes are 23 /8” (60.3) on centers and match
existing mounting patterns. Mounting screws and gasket included.
IP56 SUITABILITY.
Stylized type 316 stainless steel shore power inlet has easy to
use push-button latch that makes unit watertight when fully
engaged. Interior is heat resistant thermoset material and has box
lug terminals. Mounting holes are 23 /8” (60.3) on centers and match
existing mounting patterns. Mounting screws and gasket included.
IP56 SUITABILITY.
Traditional stainless shore power inlet has gasketed, self-closing
cover so that the interior is shielded from the elements when not in
use. It is watertight when the cover is securely fastened. The
mounting holes are 23 /8” (60.3) on centers, and the rear portion
has a 2.171” (55.1) diameter. Mounting screws and gasket are
included. IP56 SUITABILITY.
Protective rear cover. Fits all inlets except HBL504SS.
Secures to back of inlets with 3 screws which are provided.
Replacement interior for #63CM74 and #HBL504SS power inlets.
Nickel plated brass connector body has a heat resistant thermoset
interior and combination metal and rubber cord grip, which
provides superior strain relief capability. Cord grip range
is .437”-1.140” (11.1-29.0). IP20 SUITABILITY.
Yellow Seal-Tite® cover for connector bodies when used with 50A
shore power inlets. Threaded sealing ring makes connections
watertight. IP56 SUITABILITY.
White Seal-Tite® cover for connector bodies when used with 50A
shore power inlets. Threaded sealing ring makes connections
watertight. IP56 SUITABILITY.
Nickel plated brass cord clamp assembly with clamp range of
.437”-1.140” (11.1-29.0) provides strain relief for terminations on
shore power inlets.
Yellow Seal-Tite® cover for weatherproofing 50A connector bodies
on extension cords or adapters. IP55 SUITABILITY.
Notes: *Not shown.
** Not UL/CSA.
+ Boots are not UL listable.
Contact blades are
nickel plated brass
for corrosion
resistance.
HBL504SS
SR3050* **
CR16279* **
HBL63CM64
HBL77CM15+
HBL77CM15W*+
HBL77CM67*
HBL77CM17+
Self-closing cover is friction tight to remain
open while engaging cable set and shields the
interior from the elements when the inlet is not
in use.
Neoprene gasket on
underside of cover for
sealing when the cover is
closed.
Three screws “lock-in” the
interior once it is in place.
Pressure screw terminals
for secure terminationsclearly marked for easy
identification.
Thermoset contact carrier is
arcing and heat resistant.
HBL77CM17
V-12
HBL504RI
50A Traditional Stainless Steel Inlets
Base and cover are
#316 type stainless steel
for strength and
corrosion resistance.
HBL77CM15
Catalog Numbers
HBL504NM
www.hubbell-wiring.com
Rear enclosure is nickel
plated for corrosion
resistance.
Threaded base for making a watertight seal. When in use, it
mates to the threaded ring of the watertight cover on the
connector body. When not in use, it mates to the threaded
cover.
Dimensions in Inches (mm)
Marine Products
Marine Products
50 Ampere, 125/250V AC
3 Pole 4 Wire
Ship-to-Shore Devices
Y
X
Plugs and receptacles only.
W
G
50A 125/250V
50A 125/250V AC Ship-to-Shore Devices
HBL77CM16
HBL63CM69
HBL77CM74WO
50A Molded Cable Sets
Thermoset contact
carrier is arcing and
heat resistant.
Sealing lip to protect
plug/receptacle
connection from moisture.
Nickel plated brass
contact blades for
corrosion resistance.
Copper crimp
barrels for reliable
terminations.
Thermoset contact
carrier is arcing and
heat resistant.
Bull ring for
strain relief on
the terminals.
Bull ring for
strain relief on
the terminals.
Nickel plated
contacts for corrosion
resistance.
Molded-in flex
feature controls the
angle of cord entry
and keeps out
water.
Copper crimp
barrels for
reliable
terminations.
Nickel plated brass shell
for positive alignment of
keying and corrosion
resistance.
Nickel plated brass
shell for positive
alignment of keying
and corrosion
resistance.
Molded-in
flex feature
controls the
angle of
cord entry
and keeps
out water.
Metallic threaded
sealing ring to provide
a watertight seal
when mated with the
shore power inlet.
Valox® is a registered trademark of General Electric Company.
Dimensions in Inches (mm)
S750
www.hubbell-wiring.com
HBL61CM52
HBL61CM52W
HBL61CM42
HBL61CM42W
V-13
3P 4W, 50A, 125/250V TWIST-LOCK® Devices
Description
Catalog Numbers
50’ (15.2m) yellow vinyl jacketed shore power cable set, #6 AWG HBL61CM52
type STOW is completely factory pre-wired with molded-on devices.
The connector end has a metallic threaded sealing ring for making
the inlet/connector interface watertight. IP56 SUITABILITY (BOATSIDE).
Same as #HBL61CM52, except white.
HBL61CM52W
IP56 SUITABILITY (BOATSIDE).
25’ (15.2m) yellow vinyl jacketed shore power cable set, #6 AWG HBL61CM42
type STOW is completely factory pre-wired with molded-on devices.
The connector end has a metallic threaded sealing ring for making
the inlet/connector interface watertight. IP56 SUITABILITY (BOATSIDE).
Same as #HBL61CM42, except white.
HBL61CM42W
IP56 SUITABILITY (BOATSIDE).
Four conductor, #6 AWG type STOW, yellow PVC jacketed portable YC406250*
cord with jute fillers for added flexibility is ideal for making cable
sets, extension cords, and adapters that will not mark the boats
deck. Available in 250’ (76.2m) lengths only.
Nickel plated brass plug has a heat resistant thermoset interior and HBL63CM65
combination metal and rubber cord grip, which provides superior
strain relief capability. Cord grip range is .437”-1.140” (11.1-29.0).
IP20 SUITABILITY.
Yellow Seal-Tite® cover for weatherproofing 50A plugs.
HBL77CM16+
IP55 SUITABILITY.
White Seal-Tite® cover for weatherproofing 50A plugs.
HBL77CM16W*+
IP55 SUITABILITY.
Single receptacle has a heat resistant thermoset base.
HBL63CM69
IP20 SUITABILITY.
Yellow Valox® lift cover plate for weatherproofing 50A
HBL77CM74WO
receptacles. Meets requirements of the most stringent of UL’s three
listing categories for weatherproof plates. Stainless steel screws
and a neoprene gasket included. For mounting to FS/FD type
weatherproof boxes. IP44 SUITABILITY.
Same as #HBL77CM74WO except gray in color. IP44 SUITABILITY.
HBL7774WO
Stainless steel wall plate for 50A receptacle.
S750
*Not shown.
+ Boots are not UL listable.
HBL63CM65
Marine Products
100A Cable Sets
Marine Products
100 Ampere, 125/250V AC and 3ØY 120/208V AC
3, 4, & 5 Wire
Ship-to-Shore Cable Sets
Hubbell Marine was the first to offer marine grade
100 amp pin & sleeve devices. Having recognized
the need and growing demand for 100 amp shore
power devices, Hubbell worked with the National
Electric Code and American Boat and Yacht
Council to standardize on these devices. Now
Hubbell Wiring Device-Kellems is offering a
complete system of 3, 4 & 5 wire 100 amp cable
sets for your shore power requirements. Using
Hubbell marine pin & sleeve devices considered
second to none, the 100 amp cable set offering
will allow you to access the power that you need
from a cable set that is now manufactured under
factory controlled conditions.
V-14
Features
Factory assembled.
100 Amp pin & sleeve devices.
UL Listed 100 amp cable.
Breadth of line.
100% inspection.
www.hubbell-wiring.com
Benefits
Reliable and consistent
terminations.
Rugged, watertight, UL listed,
ABYC approved,
corrosion resistant.
High visibility yellow, STOW
cable, 105° C rated,
and UL listed.
Available in 75, 100, and 125 ft.
lengths with and without a
neutral. Fifty foot extension
cords also available.
Each cable set is tested to
ensure quality performance.
Dimensions in Inches (mm)
Marine Products
Marine Products
100 Ampere, 125/250 Volt and 3ØY 120/208 Volt
3, 4, & 5 Wire
Ship-to-Shore Cable Sets
IP67
SUITABILITY
100A
125/250V
100A 125/250V Ship-to-Shore Cable Sets
Description
75’ (22.8m) yellow, corrosion resistant shore power cable set,
105° C rated, 2 AWG, 2 pole 3 wire (no neutral), STOW cable
with 3 pole 4 wire, 100A 125/250V plug and connector body for
use with boats with isolation transformer on board.
Same as #CS75IT4 except 100’ (30.4m) in length.
75’ (22.8m) yellow, corrosion resistant shore power cable set,
105° C rated, 2 AWG, 3 pole 4 wire STOW cable.
Same as #CS754 except 100’ (30.4m) in length.
50’ (15.2m) yellow, corrosion resistant extension cord,
105° C rated, 2 AWG, 3 pole 4 wire STOW cable. For mating with
existing shore power cable set.
75’ (22.8m) yellow, corrosion resistant one-ended (male only)
power supply cable, 105° C rated, 2 AWG, 3 pole, 4 wire STOW
cable with 3 pole, 4 wire male plug only; for use with boats using
a cable winch system.
100’ (30.4m) yellow, corrosion resistant one-ended (male only)
power supply cable, 105° C rated, AWG, 2 pole 3 wire
(no neutral) STOW cable with 3 pole 4 wire male plug only;
for use with boats with isolation transformer on board and a
cable winch system.
Same as #CW100IT4 except 125’ (38.0m) in length.
Catalog Numbers
CS75IT4
CS100IT4
CS754
CS75IT4
CS1004
CS50EXT4
CW754
CW100IT4
CS754
CW125IT4
100A 120/208V AC Ship-to-Shore Cable Sets
Catalog Numbers
CS75IT5
CS100IT5
CS50EXT5
CW100IT5
CW125IT5
100A Cable
?????
Sets
Description
75’ (22.8m) yellow, corrosion resistant shore power cable set,
105° C rated, 2 AWG, 3 pole 4 wire (no neutral), STOW cable
with 4 pole 5 wire, 100A 120/208V plug and connector body for
use with boats with isolation transformer on board.
Same as #CS75IT5 except 100’ (30.4m) in length.
50’ (15.2m) yellow, corrosion resistant extension cord,
105° C rated, 2 AWG, 4 pole 5 wire STOW cable.
For mating with existing shore power cable set.
100’ (30.4m) yellow, corrosion resistant one-ended (male only)
power supply cable, 105° C rated, 2 AWG, 3 pole 4 wire
(no neutral) STOW cable with 4 pole 5 wire male plug only;
for use with boats with isolation transformer on board and a
cable winch system.
Same as #CW100IT5 except 125’ (38.0m) in length.
Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of
the pins and sleeves of these devices is necessary to enjoy years of optimal
use.
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-15
Marine Products
Marine Products
100 Ampere, 125/250 Volt
3 Pole 4 Wire
Ship-to-Shore Devices
IP67
SUITABILITY
100A 125/250V Ship-to-Shore Devices
M4100B12R
M4100C12R
100A
125/250V
Description
Catalog Numbers
Gray nylon shore power inlet has gasketed,
M4100B12R
spring-loaded cover which closes automatically when not in
use and is watertight when securely fastened. Mounting holes
are 47 /8” (123.8) on centers and rear portion has 315 /16” (100.0)
diameter. Mounting screws and gasket included.
Yellow supertough nylon watertight connector body has
M4100C12R
gasketed locking ring to make inlet/connector interface
watertight. Cord grip range is 1.000”-1.940” (25.4-49.3).
Note: This device mates with shore power inlet only.
15° angle cast aluminum back box has corrosion resistant
BB1001W
gray finish and top hub with 11 /2” N.P.T. 100A receptacles
can be mounted directly to it.
Same as #BB1001W except threaded top hub is 2” N.P.T.
BB1002W
15° angle non-metallic back box, made of high-grade engineered BB100N
thermoplastic Valox® to resist chemicals, abuse and U.V. rays. Has
integral grounding plate, 11 /2” NPT hub size and 120 cu. in. capacity
(hub is not included - Raco part number 1706 is recommended).
Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of
the pins and sleeves of these devices is necessary to enjoy years of optimal
use.
Valox® is a registered trademark of General Electric Company.
3P 4W, 100A, 125/250V Pin and Sleeve Devices
BB1001W
BB1002W
Shore Power Inlet
The gasketed, self-closing
cover is keyed to normally
seat in a position that provides
a weatherproof seal. Simply
rotating the cover and locking
it makes it watertight.
The terminals are clearly
identified with large markings
for easy recognition.
BB100N
High impact thermoset
contact carrier is arcing and
heat resistant.
The device is marked
with its catalog number
and rating for easy
identification.
Nickel plated solid
brass pins provide for
long life and reliable
electrical contact in
corrosive
environments.
Special keying makes
proper alignment of mating
devices quick and easy.
Nylon housing provides
increased safety and
abuse resistance.
Valox® is a registered trademark of General Electric Company.
V-16
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
100 Ampere, 125/250V AC
3 Pole 4 Wire
Ship-to-Shore Devices
IP67
SUITABILITY
100A
125/250V
100A 125/250V Ship-to-Shore Devices
Description
Catalog Numbers
Yellow supertough nylon watertight plug has gasketed locking
M4100P12
ring to make plug/receptacle interface watertight. Cord grip range
is 1.000”-1.940” (25.4-49.3).
Gray nylon dockside receptacle has gasketed,spring-loaded
M4100R12
cover. Closes automatically when not in use and is watertight
when securely fastened. Mounting holes are 47 /8” (123.8) on
centers. Mounting screws and gasket included.
Yellow supertough nylon watertight connector body for mating
M4100C12
plug to connector interface on extension cords or adapters. Cord
grip range is 1.000”-1.940” (25.4-49.3).
Note: It cannot be mated to the shore power inlet.
Back box for inlets and receptacles has 15° angle section which
FW60100
can be installed in any of 4 positions. Box is cast aluminum with
corrosion resistant gray alkyd-based enamel finish and 1 1 /2” N.P.T.
hub which can be mounted for either top or bottom feed.
Closure cap for 100A plugs and connector bodies that do not
PC100
have a cap attached.
Replacement cover assembly; includes cover, arm, spring pin
CA100
and assembly tool
Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of
the pins and sleeves of these devices is necessary to enjoy years of optimal use.
M4100P12
M4100R12
M4100C12
6.75"
(171.5)
9.75"
(247.7)
8.75"
(222.3)
3P 4W, 100A, 125/250V Pin and Sleeve Devices
6.00"
(152.4)
7.75"
(196.9)
FW60100
FW60100
100A Connector Body
The gasketed locking ring
engages the mating device
and when rotated and locked
makes the interface between
the devices watertight.
The terminals are
clearly identified
with large
markings for
easy recognition.
Massive external cable grips protect the
wiring by preventing conductor movement
which can cause strain on the terminals.
High impact thermoset
contact carrier is arcing
and heat resistant.
All screws are
stainless steel for
corrosion resistance.
PC100
Special keying
makes proper
alignment of
mating devices
quick and easy.
Neoprene glands are provided in
graduated sizes for use with
varying cable sizes. They assure a
highly reliable watertight seal at the
cable entry to the device.
Two screw pressure
terminals provide reliable
terminations.
Dimensions in Inches (mm)
Supertough nylon housing provides
increased safety and abuse resistance.
The device is marked with its
catalog number and rating for
easy identification.
www.hubbell-wiring.com
CA100
V-17
Marine Products
Marine Products
100 Ampere, 3ØY 120/208V AC
4 Pole 5 Wire
Ship-to-Shore Devices
IP67
SUITABILITY
100A 3ØY 120/208V AC Ship-to-Shore Devices
M5100B9R
4P 5W, 100A, 120/208V AC 3ØY Pin and Sleeve Devices
M5100C9R
Description
Catalog Numbers
Gray nylon shore power inlet has gasketed, spring-loaded cover M5100B9R
which closes automatically when not in use and is watertight
when securely fastened. Mounting holes are 47 /8” (123.8) on
centers and rear portion has 315 /16” (100.0) diameter. Mounting
screws and gasket included.
Yellow supertough nylon watertight connector body has
M5100C9R
gasketed locking ring to make inlet/connector interface watertight.
Cord grip range is 1.000”-1.940” (25.4-49.3).
Note: This device mates with shore power inlet only.
15° angle cast aluminum back box has corrosion resistant gray
BB1001W
finish and top hub with 11 /2” N.P.T. 100A receptacles can be
mounted directly to it.
Same as #BB1001W except threaded top hub is 2” N.P.T.
BB1002W
15° angle non-metallic back box, made of high-grade engineered BB100N
thermoplastic Valox® to resist chemicals, abuse and U.V. rays. Has
integral grounding plate, 11 /2” NPT hub size and 120 cu. in. capacity
(hub is not included - Raco part number 1706 is recommended).
Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of
the pins and sleeves of these devices is necessary to enjoy years of optimal use.
Valox® is a registered trademark of General Electric Company.
BB1001W
BB1002W
Shore Power Inlet
The device is marked
with its catalog number
and rating for easy
identification.
The gasketed, self-closing
cover is keyed to normally
seat in a position that provides
a weatherproof seal. Simply
rotating the cover and locking
it makes it watertight.
The terminals are clearly
identified with large markings
for easy recognition.
BB100N
V-18
High impact thermoset
contact carrier is arcing and
heat resistant.
www.hubbell-wiring.com
Nickel plated solid
brass pins provide for
long life and reliable
electrical contact in
corrosive
environments.
Special keying makes
proper alignment of mating
devices quick and easy.
Nylon housing provides
increased safety and
abuse resistance.
Dimensions in Inches (mm)
Marine Products
Marine Products
100 Ampere, 3ØY 120/208V AC
4 Pole 5 Wire
Ship-to-Shore Devices
IP67
SUITABILITY
M5100P9
100A 3ØY 120/208V AC Ship-to-Shore Devices
M5100R9
M5100C9
4P 5W, 100A, 120/208V AC 3ØY Pin and Sleeve Devices
Description
Catalog Numbers
Yellow Super tough nylon watertight plug has gasketed
M5100P9
locking ring to make plug/receptacle interface watertight.
Cord grip range is 1.000”-1.940” (25.4-49.3).
Gray nylon dockside receptacle has gasketed, spring-loaded
M5100R9
cover. Closes automatically when not in use and is watertight
when securely fastened. Mounting holes are 47 /8” (123.8)
on centers. Mounting screws and gasket included.
Yellow Super tough nylon watertight connector body for
M5100C9
making plug to connector interface on extension cords or
adapters. Cord grip range is 1.000”-1.940” (25.4-49.3).
Note: It cannot be mated to the shore power inlet.
Back box for inlets and receptacles has 15° angle section which
FW60100
can be installed in any of 4 positions. Box is cast aluminum with
corrosion resistant gray alkyd-based enamel finish and 11 /2” NPT
hub which can be mounted for either top or bottom feed.
Closure cap for 100A plugs and connector bodies that do not
PC100
have a cap attached.
Replacement cover assembly; includes cover, arm, spring, pin
CA100
and assembly tool.
Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of
the pins and sleeves of these devices is necessary to enjoy years of optimal use.
6.75"
(171.5)
9.75"
(247.7)
6.00"
(152.4)
8.75"
(222.3)
7.75"
(196.9)
FW60100
FW60100
100A Connector Body
The gasketed locking ring
engages the mating device
and when rotated and locked
makes the interface between
the devices watertight.
The terminals are
clearly identified
with large
markings for
easy recognition.
Massive external cable grips protect the
wiring by preventing conductor movement
which can cause strain on the terminals.
High impact thermoset
contact carrier is arcing
and heat resistant.
All screws are
stainless steel for
corrosion resistance.
PC100
Special keying
makes proper
alignment of
mating devices
quick and easy.
Neoprene glands are provided in
graduated sizes for use with
varying cable sizes. They assure a
highly reliable watertight seal at the
cable entry to the device.
Two screw pressure
terminals provide reliable
terminations.
Dimensions in Inches (mm)
Supertough nylon housing provides
increased safety and abuse resistance.
The device is marked with its
catalog number and rating for
easy identification.
www.hubbell-wiring.com
CA100
V-19
Marine Products
Marine Products
20 Ampere, 125 Volt
2 Pole 3 Wire
TWIST-LOCK® Locking Type Devices
W
G
Plugs and receptacles only.
20A, 125V AC
NEMA L5-20R
20A 125V Twist-Lock Devices
HBL23CM10
HBL7425WOA
HBL74CM25WOA
HBL74CM25WOAW
2P 3W, 20A, 125V TWIST-LOCK® Devices
HBL23CM11
Description
Catalog Numbers
Yellow single receptacle has Rynite® body and abuse resistant
HBL23CM10
nylon face. IP20 SUITABILITY.
Yellow polycarbonate spring-loaded lift cover plate for weatherHBL74CM25WOA
proofing #HBL23CM10 receptacle. Meets the most stringent
requirements of UL’s three listing categories for weatherproof
plates. Stainless steel screws and neoprene gasket included for
mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY.
Same as #HBL74CM25WOA except gray in color. IP44 SUITABILITY.
HBL7425WOA
Same as #HBL74CM25WOA except white in color. IP44 SUITABILITY. HBL74CM25WOAW
Yellow Insulgrip® plug has rugged nylon housing and cord grip
HBL23CM11
with range of .360”-.930” (9-24) that utilizes a unique offset jaws
arrangement to provide secure strain relief. IP20 SUITABILITY.
Yellow Seal-Tite® cover for weatherproofing #HBL26CM11 or
HBL60CM31+
#HBL23CM11 plugs. IP55 SUITABILITY.
Note: Fits Insulgrip® devices only.
Same as #HBL60CM31 except white in color.
HBL60CM31W+
Yellow Insulgrip® connector body has rugged nylon housing and
HBL23CM13
cord grip with range of .360”-.930” (9-24) that utilizes a unique
offset jaws arrangement to provide secure strain relief. IP20 SUITABILITY.
HBL60CM32+
Yellow Seal-Tite® cover for weatherproofing #HBL26CM13 or
#HBL23CM13 connector bodies when used on extension cords
or adapters. IP55 SUITABILITY. Note: Fits Insulgrip® devices only.
Yellow Valise® plug has one-piece nylon housing, assembles
HBL23CM11V
easily with two screws. Built-in cord grip has range of
.325”-.720” (8.3-18.2). IP20 SUITABILITY.
Yellow vinyl Seal-Tite® cover for weatherproofing #HBL23CM11V HBL60CM31V+
or #HBL26CM11V plugs. IP55 SUITABILITY.
Note: Fits Valise® devices only.
Three conductor, #12 AWG type STW, yellow PVC jacketed
YC312250*
portable cord with jute fillers for added flexibility. Ideal for making
cable sets, extension cords and adapters as will not mark boat’s
deck. Available in 250’ (76.2m) lengths only.
Notes: *Not shown.
+ Boots are not UL listable.
Rynite® is a registered trademark of E. I. Dupont.
HBL60CM31
HBL60CM31W
HBL23CM13
HBL60CM32
V-20
HBL23CM11V
HBL60CM31V
www.hubbell-wiring.com
HBL23CM13V
HBL60CM32V
Dimensions in Inches (mm)
Marine Products
Marine Products
20 Ampere, 125V AC
2 Pole 3 Wire
Straight Blade Devices
G
P
W
20A 125V
20A 125V AC Straight Blade Devices
NEMA 5-20R
HBL52CM21
HBL52CM21W
Dimensions in Inches (mm)
HBL61CM65
HBL74CM23WO
HBL7423WO
www.hubbell-wiring.com
HBL53CM66C
HBL53CM69C
HBL60CM18
HBL60CM19
HBL60CM17
2P 3W, 20A, 125V Straight Blade Devices
Description
Catalog Numbers
Yellow Insulgrip® plug has rugged nylon housing and detachable
HBL53CM66C
cord grip with range of .230” - .720” (5.8-18.3) that utilizes unique
offset jaws arrangement to provide secure strain relief. IP20 SUITABILITY.
Yellow Insulgrip® connector body has rugged nylon housing and
HBL53CM69C
cord grip with range of .230” - .720” (5.8-18.3) that utilizes unique
offset jaws arrangement for secure strain relief. IP20 SUITABILITY.
Yellow Seal-Tite® cover for weatherproofing straight blade
HBL60CM18+
Insulgrip connector bodies, #HBL52CM69C and #HBL53CM69C,
on extension cords and adapters. IP55 SUITABILITY.
Note: For Insulgrip® devices only.
Yellow closure plug used with #HBL60CM18 long Seal-Tite cover HBL60CM19+
to prevent water from entering front of device when not in use.
IP55 SUITABILITY.
Yellow Seal-Tite® cover for weatherproofing straight blade
HBL60CM17+
Insulgrip plugs, #HBL52CM66C and #HBL53CM66C, when used
to mate receptacles and connector bodies. Can also be used with
Insulgrip connector bodies when mating with flanged inlets.
IP55 SUITABILITY. Note: For Insulgrip® devices only.
Yellow duplex receptacle has Rynite® body.
HBL53CM62
Receptacle accepts both 20A 125V and 15A 125V 2 pole, 3 wire
straight blade plugs. IP20 SUITABILITY.
Single version of #HBL53CM62 duplex yellow receptacle.
HBL53CM61
IP20 SUITABILITY.
Compact gray nylon panel mount outlet ideal for electric trolling
HBL61CM65
motors and reel applications. Features gasketed spring-loaded
lift cover for weatherproofing front and neoprene boot for
weatherproofing rear. Accepts both 20A 125V and 15A 125V
2 pole, 3 wire straight blade plugs. IP55 SUITABILITY.
Yellow polycarbonate spring-loaded lift cover plate for
HBL52CM21
weatherproofing duplex receptacles. Stainless steel screws
and neoprene gasket included for mounting to FS/FD type
weatherproof boxes. IP20 SUITABILITY. Not CSA.
Same as #HBL52CM21 except white in color. IP20 SUITABILITY.
HBL52CM21W
Same as #HBL52CM21 except gray in color.
HBL5221*
IP20 SUITABILITY.
Same as #HBL52CM21 except for mounting to standard boxes.
HBL52CM22*
IP20 SUITABILITY.
Same as #HBL52CM22 except gray in color.
HBL5222*
IP20 SUITABILITY.
Yellow polycarbonate spring-loaded lift cover plate for
HBL74CM23WO
weatherproofing single straight blade receptacles. Stainless
steel screws and neoprene gasket included. For mounting to
FS/FD type weatherproof boxes. IP44 SUITABILITY. Not CSA
Same as #HBL74CM23WO except gray in color.
HBL7423WO
IP44 SUITABILITY.
Notes: *Not shown.
+ Boots are not UL listable.
Rynite® is a registered trademark of E. I. DuPont.
HBL53CM62
HBL53CM61
V-21
Marine Products
Marine Products
Boatside
Ship-to-Shore Selection Chart
Boatside
100A
3ØY
120/208V AC
4 Pole
5 Wire
Pages V-14-15,
V-18-19
100A
125/250V AC
3 Pole
4 Wire
Pages V-14-17
50A
125/250V AC
3 Pole
4 Wire
Non-Metallic
Stainless Steel
(W)
Pages V-12-13
50A
125V AC
2 Pole
3 Wire
Ship-to-Shore Selection Chart
Pages V-10-11
(W)
30A
125V AC
2 Pole
3 Wire
(W)
(W)
Pages V-2-7
Portable
Telephone
Cable
TV
Pages V-8-9
V-22
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
Dockside
Ship-to-Shore Selection Chart
Dockside
Ship-to-Shore Selector Chart
(W)
(W)
(W)
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-23
Ship-to-Shore Selection Chart
HBL74CM25WOAW
Marine Products
Marine Products
Intelligent Y Adapters
YQ230 - Safely powers a 50A, 125/250V AC boat from two 30A, 125V AC receptacles at dockside.
Environmentally sealed against humidity, fog and rain.
Cord clamps prevent
strain on terminals.
Application:
Problem: A boat owner with one
electrical system on board docks in a
marina that can only provide a different
electrical system.
Sealing grommets
keep moisture out. Solution: Use of the Hubbell YQ
series of Intelligent Adapters can
correct many electrical system mismatches.
UV resistant high-impact housing.
Safety indicator light.
(When on, safe operation is indicated.)
Features and Benefits:
• 3 pole contactor breaks both hots
and neutrals to prevent possibility of
“live” plug when not engaged.
Fully molded Hubbell plugs.
30A plugs connect
to 30A shore power.
50A connector
body mates with
boat's male end
of cordset.
Fully molded Hubbell connector.
• The two receptacles are from
opposite phases (i.e., there is a true
250V available instead of just 125V).
Note: The YQ230 Adapter will only
work with two 30A receptacles that
are on different circuits.
YQ100 - Safely powers a 100A, 125/250V AC boat from two 50A 125/250V AC receptacles at dockside.
50A plugs connect
to 50A shore power.
Fully molded Hubbell plugs.
Full feature Hubbell connector.
Internal Logic Senses That:
• Both plugs are fully engaged (i.e.,
one is not dangling loose while the
other is plugged in).
Cord clamps prevent
strain on terminals.
100A connector
body mates with
boat cordset.
Environmentally sealed against humidity, fog and rain.
• The polarity of the receptacle on
the dock is correct (i.e., no miswiring of the hot and neutral wires).
Intelligent Adapters
• The two receptacles are from
correct phases.
Indicator lights
indicate correct
polarity and safe
operation.
Note: The YQ100 Adapter must be
plugged into two 50A 125/250V AC
receptacles that are on the same
phase.
Sealing grommets
keep moisture out.
Intelligent Y Adapters
Description
Adapter that permits use of 50A, 125/250V AC cable set. (#HBL61CM52),
with two 30A, 125V AC receptacles, #HBL26CM10.
Adapter that permits use of 100A, 125/250V AC cable set. (#CS754, CS1004)
with two 50A, 125/250V AC receptacles, #63CM69.
V-24
www.hubbell-wiring.com
Catalog Numbers
YQ230
YQ100
Dimensions in Inches (mm)
Marine Products
Marine Products
Adapter Selection Guide
Boat/Cable Set Side
Power Center/Dock Side
Catalog Numbers
Molded Straight
Adapters
Connector Body (Female End)
Plug (Male End)
W
G
15A 125V, 2P 3W Straight
HBL105GF*
W
30A 125V, 2P 3W Twist-Lock
G
W
W
30A 125V, 2P 3W Twist-Lock
G
50A 125V, 2P 3W Twist-Lock
W
G
HBL61CM22
HBL61CM22W
HBL61CM25
G
W
W
G
30A 125V, 2P 3W Twist-Lock
15A 125V, 2P 3W
Straight Blade (lock type)
20A 125V, 2P 3W Twist-Lock
G
HBL61CM54
15A 125V, 2P 3W Straight Blade
W
G
W
30A 125V, 2P 3W Twist-Lock
HBL61CM55
G
W
G
50A 125V, 2P 3W Twist-Lock
W
50A 125V, 2P 3W Twist-Lock
HBL61CM56
W
G
G
30A 125V, 2P 3W Twist-Lock
Y
50A 125/250V, 3P 4W Twist-Lock
W
HBL61CM59
X
W
Y
W
30A 125V, 2P 3W Twist-Lock
50A 125/250V, 3P 4W Crow Foot
X
G
Y
HBL61CM71
G
X
W
50A 125/250V, 3P 4W Twist-Lock
G
Y
50A 125V, 2P 3W Twist-Lock
HBL61CM72
W
G
X
W
50A 125/250V, 3P 4W Twist-Lock
G
Y
100A 125/250V, 3P 4W Pin/Sleeve
HBL61CM100
X
W
50A 125/250V, 3P 4W Twist-Lock
G
Molded “Y” Adapters
(2) 30A 125V, 2P 3W Twist-Lock
W
W
HBL64CM54
G
G
Y
X
50A 125/250V, 3P 4W Twist-Lock
W
G
(2) 50A 125V, 2P 3W Twist-Lock
(2) 30A 125V, 2P 3W Twist-Lock
G
50A 125/250V, 3P 4W Twist-Lock
G
W
G
X
W
G
G
(2) 30A 125V, 2P 3W Twist-Lock
Y
HBL64CM55
W
W
W
W
HBL64CM56
G
G
30A 125V, 2P 3W Twist-Lock
W
W
HBL64CM57
G
W
50A 125V, 2P 3W Twist-Lock
G
W
W
(2) 30A 125V, 2P 3W Twist-Lock
G
HBL64CM59
G
W
50A 125/250V, 3P 4W Crow Foot
X
Y
W
30A 125V, 2P 3W Twist-Lock
HBL31CM28
G
15A 125V, 2P 3W Straight Blade
G
W
G
15 or 20A 125V, 2P 3W Straight Blade
W
HBL31CM29
30A 125V, 2P 3W Twist-Lock
W
G
W
20A 125V, 2P 3W Twist-Lock
HBL21CM28
G
15A 125V, 2P 3W Straight Blade
G
W
15 or 20A 125V, 2P 3W Straight Blade
G
W
HBL21CM29
20A 125V, 2P 3W Twist-Lock
W
G
Note: See following two pages for photographs and descriptions.
*Provides GFCI Protection
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-25
Adapter Selection Guide
One Piece Adapters
Marine Products
IP65
Marine Products
SUITABILITY
Molded Straight Adapters
Molded Straight Adapters
HBL21CM28
HBL21CM29
HBL31CM28
HBL31CM29
HBL61CM25
HBL61CM22
HBL61CM22W
Description
Permits use of 20A 125V Twist-Lock® locking type plug with
15 or 20A 125V straight blade receptacle. IP20 SUITABILITY.
Permits use of 15A or 20A 125V straight blade plug with
20A 125V Twist-Lock locking type receptacle. IP20 SUITABILITY.
Permits use of 30A 125V Twist-Lock® locking type plug with
15 or 20A 125V straight blade receptacle. IP20 SUITABILITY.
Permits use of 15A or 20A 125V straight blade plug with
30A 125V Twist-Lock locking type receptacle. IP20 SUITABILITY.
Permits use of 30A 125V cable set, #HBL61CM08, with
15 or 20A 125V straight blade receptacle. Anchor locking screw
on plug when screwed down resists pullout of the cable set.
Same as #HBL61CM22, except white.
Permits use of 30A 125V cable set, #HBL61CM08, with
20A 125V Twist-Lock® receptacle, #HBL23CM10.
Permits use of 50A 125V cable set, #HBL61CM53, with
15 or 20A 125V straight blade receptacle.
Permits use of 30A 125V cable set, #HBL61CM08, with
50A 125V Twist-Lock® receptacle, #HBL63CM70.
Permits use of 50A 125V cable set, #HBL61CM53, with
30A 125V Twist-Lock® receptacle, #HBL26CM10.
Permits use of 50A 125/250V Twist-Lock® locking type
cable set, #HBL61CM52, with 50A 125/250V crow foot
straight blade receptacle #HBL7962.
Permits use of 30A 125V cable set, #HBL61CM08, with
50A 125/250V Twist-Lock® receptacle, #HBL63CM69.
Permits use of 50A 125V cable set, #HBL61CM53, with
50A 125/250V Twist-Lock® receptacle, #HBL63CM69.
Permits use of 15A 125V 3 wire straight blade plug with
15 or 20A 125V 2 wire straight blade receptacle.
Permits a 100 amp 125/250 volt cable set to plug into a
single 50 amp 125/250 volt outlet.
Permits use of 15A straight blade plug with 30A 125V
Twist-Lock® receptacle; with GFCI protection.
Catalog Numbers
HBL21CM28**
HBL21CM29**
HBL31CM28
HBL31CM29
HBL61CM22
HBL61CM22W
HBL61CM25
HBL61CM54
HBL61CM55
HBL61CM56
HBL61CM59
HBL61CM71Ž
HBL61CM72Ž
HBL5273L* **
HBL61CM100
HBL105GF
Notes: *Not shown.
** UL listed.
Adapters do not provide overcurrent protection.
Adapters do not provide GFCI protection except HBL105GF.
ŽThe male plug end (50A 125/250V) has a blade removed and the blade slot
filled with epoxy Omitting the blade ensures achieving 125V safely.
Straight Adapters
HBL105GF
HBL61CM55
HBL61CM55
HBL61CM54
HBL61CM59
HBL61CM56
V-26
HBL61CM71
HBL61CM100
www.hubbell-wiring.com
HBL61CM71Ž
HBL61CM72Ž
Dimensions in Inches (mm)
SUITABILITY
Molded Y Adapters
Molded Y Adapters
Description
Permits use of two 30A 125V cable sets, #HBL61CM08, with
one 50A 125/250V receptacle, #HBL63CM69.
Permits use of two 50A 125V cables sets, #HBL61CM53, with
one 50A 125/250V receptacle, #HBL63CM69.
Permits use of two 30A 125V cable sets, #HBL61CM08, with
one 30A 125V receptacle, #HBL26CM10.
Permits use of two 30A 125V cable sets, #HBL61CM08, with
one 50A 125V receptacle, #HBL63CM70.
Permits use of two 30A 125V cable sets, #HBL61CM08, with
one 50A 125/250V crow-foot straight receptacle, #HBL7962.
Notes:
Marine Products
IP65
Marine Products
Catalog Numbers
HBL64CM54
HBL64CM55
HBL64CM56
HBL64CM57
HBL64CM56
HBL64CM59
The adapters shown on this page are not UL Listed because of the nature of
adapters with their variety of ratings.
Adapters do not provide overcurrent protection.
Adapters do not provide GFCI protection except HBL105GF.
HBL64CM55
HBL64CM54
HBL64CM59
HBL64CM57
Y-Adapters
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-27
Marine Products
Marine Products
Internationally Rated
16, 32, 63 Ampere, 240 Volt
Pin and Sleeve Devices
IP67
SUITABILITY
UL Classified to IEC 60309-1 and 60309-2
Devices are 2 pole plus earth ( ) rated 240V in either 16A, 32A or 63A.
HBL316B6W
HBL316R6W
2 Pole
2 Pole
Internationally Rated Pin and Sleeve Devices
HBL316C6W
16A 240V
Description
Shore power inlet with mounting holes 3 1/8” (79.3) on centers
and 2 23/32” (69.1) diameter on rear portion.
Connector body with cord grip range of .360”-.830” (9.1-21.1).
Shore power receptacle with mounting holes 3 1/8” (79.3)
on centers and 2 23/32” (69.1) diameter on rear portion.
Plug with cord grip range of .360”-.830” (9.1-21.1).
Closure plug for #HBL316B6W. Not CSA.
Back box for inlets and receptacles is cast aluminum with
corrosion resistant alkyd-based enamel finish and two 3/4”
N.P.T. hubs.
Feed-thru box for inlets and receptacles is cast aluminum with
corrosion resistant alkyd-based enamel finish and one 3/4”
N.P.T. hubs.
Catalog Numbers
HBL316B6W
HBL316C6W
HBL316R6W
HBL316P6W
PC320
BB201W
FT202W
32A 240V
Description
Shore power inlet with mounting holes 3 1/8” (79.3) on centers
and 2 23/32” (69.1) diameter on rear portion.
Connector body with cord grip range of .450”- 1.250” (11.4-31.8).
Shore power receptacle with mounting holes 31/8” (79.3) on
centers and 2 23/32” (69.1) diameter on rear portion.
Plug body with cord grip range of .450”- 1.250” (11.4-31.8).
Closure plug for #HBL332B6W. Not CSA.
Back box for inlets and receptacles is cast aluminum with
corrosion resistant alkyd-based enamel finish and one
1” N.P.T. hub.
Catalog Numbers
HBL332B6W
HBL332C6W
HBL332R6W
HBL332P6W
PC3430
BB301W
HBL316P6W
2 Pole
PC320
63A 240V
Description
Shore power inlet with mounting holes 3 7 /8” (98.4) on centers
and 315 /32” (88.1) diameter on rear portion.
Connector body with cord grip range of .700”- 1.450” (17.8-36.8).
Shore power receptacle with mounting holes 3 7 /8” (98.4) on
centers and 315 /32” (88.1) diameter on rear portion.
Plug body with cord grip range of .700”- 1.450” (17.8-36.8).
Closure plug for #HBL363B6W. Not CSA.
Back box with 11/2” N.P.T. hub.
Back box for inlets and receptacles has 15° angle section which
can be installed in any of 4 positions. Box is cast aluminum with
corrosion resistant gray alkyd-based enamel finish and 11/2” N.P.T.
hub which can be mounted for either top or bottom feed.
Catalog Numbers
HBL363B6W
HBL363C6W
HBL363R6W
HBL363P6W
PC60
BB601W
FW60100
BB201W
V-28
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
Internationally Rated
16, 32 Ampere, 230 Volt
Ship-to-Shore Power System
Hubbell offers the only CE certified electrical shore power system truly
dedicated for boats destined for Europe and the International
community. Hubbell’s offering of international shore power inlets is
available in stylized #316 Type Stainless Steel as well as attractive
white non-metallic types resembling our domestic offering in style and
appearance but are not interchangeable with the domestic shore power
system.
Utilizing standard NEMA (National Electrical Manufacturer’s
Association) configurations not typically used in the marine market,
Hubbell can offer a safe and non-interchangeable 16 Amp 230 Volt
system and 32 Amp 230 Volt system for use with 50 cycle systems. The
system includes white power supply cables (one-end, female only) in
both the 16 Amp and 32 Amp categories.
HBL316NM
HBL332NM
IP56
SUITABILITY
16 Amp 230 Volt
Ship-To-Shore Power System
Catalog Numbers
HBL316NM
HBL316SSX
HBL316CSW25
HBL316CSW
HBL316CRC
HBL103RX
32 Amp 230 Volt, 50 Cycle Ship-To-Shore Power System
Description
Non-metallic, white, stylized, U.V. resistant shore power inlet. White
Centrex cover makes the inlet weatherproof when closed. Mounting
holes are 2 3/8” (60.3) on centers and match most existing mounting
patterns. Rear enclosure/strain relief cap is provided.
Traditional, stainless steel shore power inlet has new easy-to-wire
terminations. Interior is transparent for quick and easy visual
inspection. Interior is shielded from the elements by a gasketed,
self-closing cover, watertight when cover is screwed in place.
Mounting holes are 23 /8” (60.3) on centers. Mounting screws and
gasket included. Protective rear enclosure/strain relief also included.
50 ft. (15.2m) white, vinyl jacketed power supply cord with female
(boat side) end only; other end blunt cut.
Yellow locking connector replacement end for #HBL332CSW.
White Seal-Tite cover with threaded sealing ring for use with
#HBL316CRC and #HBL332CRC connector bodies.
Dimensions in Inches (mm)
HBL316SSX
HBL332SSX
Internationally Rated Twist-Lock® Devices
Description
Non-metallic, white, stylized, U.V. resistant shore power inlet. White
Centrex cover makes the inlet weatherproof when closed. Mounting
holes are 2 3/8” (60.3) on centers and match most existing
mounting patterns. Rear enclosure strain/relief cap is provided.
Traditional, stainless steel shore power inlet has new easy-to-wire
terminations. Interior is transparent for quick and easy visual
inspection. Interior is shielded from the elements by a gasketed,
self-closing cover, watertight when cover is screwed in place.
Mounting holes are 23 /8” (60.3) on centers. Mounting screws and
gasket included. Protective rear enclosure/strain relief also included.
25’ (7.6m) white, vinyl jacketed power supply cord with female
(boat side) end only; other end blunt cut.
50’ (15.2m) white, vinyl jacketed power supply cord with female
(boat side) end only; other end blunt cut.
Yellow locking connector replacement end for #HBL316CSW25
& #HBL316CSW.
White Seal-Tite cover with threaded sealing ring for use with
#HBL316CRC and #HBL332CRC connector bodies.
HBL316CSW25
HBL316CSW
HBL332CSW
Catalog Numbers
HBL332NM
HBL332SSX
HBL316CRC
HBL332CRC
HBL332CSW
HBL332CRC
HBL103RX
www.hubbell-wiring.com
HBL103RX
V-29
Marine Products
Marine Products
15 Ampere, 125V AC
2 Pole 3 Wire
TWIST-LOCK® Locking Type Devices
W
G
P
15A 125V
15A 125V AC Twist-Lock Devices
HBL47CM00
HBL52CM21
HBL52CM21
HBL52CM21W
2P 3W, 15A, 125V, TWIST-LOCK® Devices
HBL47CM20C
NEMA L5-15R
Description
Catalog Numbers
Yellow duplex receptacle has heat resistant body. IP20 SUITABILITY. HBL47CM00
HBL52CM21
Yellow Valox® spring-loaded lift cover plate for weatherproofing
duplex receptacles. Stainless steel screws and neoprene gasket
included for mounting to FS/FD type weatherproof boxes.
IP20 SUITABILITY.
Same as #HBL52CM21 except white in color. IP20 SUITABILITY.
HBL52CM21W
Same as #HBL52CM21 except gray in color. IP20 SUITABILITY.
HBL5221
Same as #HBL52CM21 except for mounting to standard boxes.
HBL52CM22*
IP20 SUITABILITY.
Same as #HBL52CM22 except gray in color. IP20 SUITABILITY.
HBL5222*
Yellow Insulgrip® plug has rugged nylon housing and detachable HBL47CM20C
cord grip with range of .296”-.687” (7.5-17.4) that utilizes a unique
offset jaws arrangement to provide secure strain relief.
Short yellow Seal-Tite® cover for weatherproofing #HBL47CM20C HBL60CM23+
Insulgrip® plug when used with receptacles or connector bodies.
Also can be used to weatherproof #HBL47CM29C Insulgrip®
connector body when used with #HBL47CM16 flanged inlet.
IP55 SUITABILITY.
Yellow Insulgrip® connector body has rugged nylon housing and HBL47CM29C
detachable cord grip with range of .296”-.687” (7.5-17.4) that
utilizes a unique offset jaws arrangement to provide secure
strain relief.
HBL60CM24+
Yellow Seal-Tite® cover for weatherproofing #HBL47CM29C
Insulgrip® connector body when used on extension cords and
adapters. IP20 SUITABILITY.
Panel mount flanged outlet has heat resistant melamine interior
HBL47CM15
and stainless steel casing. IP20 SUITABILITY.
Panel mount flanged inlet has heat resistant melamine interior
HBL47CM16
and stainless steel casing. IP20 SUITABILITY.
Three conductor, #14 AWG type STW, yellow PVC jacketed
YC314250*
portable cord has jute fillers for added flexibility and is ideal for
making cable sets, extension cords and adapters as it will not
mark the boat’s deck. Available in 250’ (76.2m) lengths only.
Notes: *Not shown.
+ Boots are not UL listable.
Valox ® is a registered trademark of General Electric Company.
HBL60CM23
HBL60CM23
HBL47CM29C
HBL60CM24
HBL47CM15
V-30
www.hubbell-wiring.com
HBL47CM16
Dimensions in Inches (mm)
Marine Products
Marine Products
15 Ampere, 125V AC
2 Pole 3 Wire
Straight Blade Devices
G
W
IP20
SUITABILITY
15A 125V
15A 125V AC Straight Blade Devices
NEMA 5-15R
HBL52CM61
HBL52CM66C
HBL52CM69C
HBL52CM66V
2P 3W, 15A, 125V, Straight Blade Devices
Description
Catalog Numbers
Yellow single receptacle features Rynite® body and abuse
HBL52CM61
resistant nylon face.
Yellow corrosion resistant duplex receptacle. Use
HBL52CM62
where salt or other corrosive elements are a problem.
Same as #HBL52CM62 except ivory.
HBL52CM62I*
Yellow Insulgrip® plug has rugged nylon housing and detachable HBL52CM66C
cord grip with range of .230”-.720” (5.8-18.3) that utilizes a unique
offset jaws arrangement for secure strain relief.
Yellow Seal-Tite® cover for weatherproofing straight blade
HBL60CM17*+
Insulgrip plugs, #HBL52CM66C and #HBL53CM66C, when used
with receptacles and connector bodies. Can also be used to
weatherproof Insulgrip connector bodies when mating with flanged
inlets. IP55 SUITABILITY. Not UL or CSA.
Note: For Insulgrip® devices only.
Yellow Insulgrip® connector body has rugged nylon housing and HBL52CM69C
detachable cord grip with range of .230” to .720” (5.8-18.3) that
utilizes a unique offset jaws arrangement for secure strain relief.
HBL60CM18*+
Yellow Seal-Tite® cover for weatherproofing straight blade
Insulgrip connector bodies, #HBL52CM69C and #HBL53CM69C,
on extension cords and adapters. IP55 SUITABILITY. Not UL or CSA.
Note: For Insulgrip® devices only.
Yellow Valise® plug has one-piece nylon housing that assembles HBL52CM66V
easily with two screws. Built-in cord grip has range of .220”-.660”
(5.6-16.8).
Yellow Valise® connector body has one-piece nylon housing that HBL52CM69V
assembles easily with two screws. Built-in cord grip has range of
.220”-.660” (5.6-16.8).
HBL52CM80C
Yellow Insulgrip® plug with anchor locking screw to prevent
accidental pull-out. The plug is “locked” into the receptacle when
the screw is turned down so the head is flush with the plug
surface. The cord grip range is .296”-.687” (7.5-17.4).
UL Recognized Component.
Compact gray nylon panel mount inlet ideal for bass boat battery HBL61CM64
charging connection. Has gasketed spring-loaded lift cover for
weatherproofing front and neoprene boot for weatherproofing rear.
Will accept both 15A 125V and 20A 125V 2 pole, 3 wire straight
blade connector bodies.
Same as #HBL61CM64 except black in color.
HBL61CM64BK*
Yellow Valox® spring-loaded lift cover plate for weatherproofing
HBL52CM21*
duplex receptacles. Stainless steel screws and neoprene
gasket included for mounting to FS/FD type weatherproof boxes.
Same as #HBL52CM21 except gray in color.
HBL5221*
Same as #HBL52CM21 except for mounting to standard boxes.
HBL52CM22*
Same as #HBL52CM22 except gray in color.
HBL5222*
Yellow Valox® spring-loaded lift cover plate for weatherproofing
HBL74CM23WO
single straight blade receptacles. Stainless steel screws and
neoprene gasket included. For mounting to FS/FD type
weatherproof boxes. IP44 SUITABILITY.
Same as #HBL74CM23WO except gray in color.
HBL7423WO*
IP44 SUITABILITY.
Notes: *Not shown.
+ Boots are not UL listable.
HBL52CM69V
HBL52CM80C
HBL74CM23WO
HBL7423WO
Rynite ® is a registered trademark of E. I. DuPont.
Valox ® is a registered trademark of General Electric Company.
HBL61CM64
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-31
Marine Products
Marine Products
Portable Ground Fault Circuit Interrupters and Testers
GFP15M
GFT2G
HBL5200
Portable Ground Fault Circuit Interrupters (GFCIs)
These UL Listed portable GFCIs have been designed to protect people
from line-to-ground electrical shock hazards which may develop from
faulty appliance, tools or defective portable cords. If a ground fault
does occur and the leakage level exceeds 4 to 6 milliamps, the GFCI
unit quickly acts to protect the user by opening the circuit, thus
interrupting the power supply and limiting the duration of any electrical
current flow. After tripping, the module is reset by pushing a button on
its face. A test button allows the user to test that the GFCI is in working
order.
Note: GFCI devices will not protect against overloads or short circuits.
Portable Ground Fault Circuit Interrupters and Testers
Description
Catalog Numbers
This unit is small and compact - measuring only 4 3/16”H x 5 3/16”L
GFP15M
x 6 11/16” W (10.6cm H x 13.2cm L x 17.0cm W) and weighing only
3 pounds - yet protects as many as four tools at one time.
The housing is high impact yellow polycarbonate as are the
liftcovers which protect the receptacles from dirt and damage.
Simply insert the plug on the end of the 6’ (1.8m) cord into any
60Hz 120V receptacle and then plug the equipment to be used
into one of the receptacles on the unit. Incorporates a 20 Amp
GFCI module that can be replaced in the field. The module
provides not only ground fault protection, but also contains the
no voltage release feature.
3-outlet plug-in unit. Plugs into boat convenience receptacles
GFP315A
to provide ground fault protection.
This unit is designed to measure the trip level of GFCI portables,
GFT2G
receptacles, or breakers within any range from 2 to 7 milliamperes,
or the leakage in portable tools or appliances within a leakage
range of 1 to 7 milliamperes. It can be used on any AC circuit of
110 to 130V.
This outlet circuit tester has a simple arrangement of neon lights
HBL5200
which visually indicate correct wiring, reversed polarity, open
ground wire, open neutral wire, open hot wire, hot and ground
reversed and hot wire on neutral terminal, and hot terminal unwired.
Simply plug the #HBL5200 into a single phase 125V 2 pole 3 wire
outlet and the combination of lighted and/or unlighted lamps will
immediately indicate the condition of the circuit. The instructions
and symbol identification are printed on durable polyester labels
permanently attached to the tester. To test other 2 pole 3 wire single
phase 125V outlets, use one of the proper adapters shown on
pages V-26 and V-27.
Portable GFCI
GFP315A
GFP6C15M
GFP25C15M
V-32
GFCI Line Cord Devices
Ideal for personal plug-in protection at
marinas and onboard boats when used
with pumps, drills, sanders and all
portable electrical equipment. GFCI
mechanism is watertight and approved
for outdoor use. High visibility yellow
SJTW-A power cord resists moisture,
chemicals and sunlight. Two different
lengths available.
GFP6C15M 6’ (1.8m) line cord
GFP25C15M 25’ (7.6m) line cord
www.hubbell-wiring.com
GFCI Specifications
Rating: 15A 120V 60Hz 2 pole 3 wire
straight blade
Trip Level: 4-6 miliamps
Trip Time: .025 seconds nominal
Frequency: 60 Hertz nominal
Voltage: 120 volts +10%, -15%
Max Interrupting Capacity: 2,000
amperes
Max Humidity: 95%
UL Class A
Dimensions in Inches (mm)
Marine Products
Marine Products
GFCI and Surge Protection
Inside the Boat
The American Boat and Yacht Council recommends the use of ground
fault protected receptacles in a head, galley, machinery space or on a
weather deck. Refer to ABYC “Ground Fault Protection”.
Ground Fault Circuit Interrupter (GFCI) Receptacles
These UL Listed receptacles have been designed to protect people
from line-to-ground electrical shock hazards which may develop from
faulty appliance, tools or defective portable cords. If a ground fault
does occur and the leakage level exceeds 4 to 6 milliamps, the GFCI
unit quickly acts to protect the user by opening the circuit, thus
interrupting the power supply and limiting the duration of any electrical
current flow. After tripping, the receptacle is reset by pushing a button
on its face. A test button allows the user to test that the GFCI is in
working order.
GF5252MWA
Note: All Hubbell GFCI receptacles are in compliance with new UL 943
Mandate.GFCI receptacles will not protect against overloads or short
circuits.
Hubbell’s GFCI receptacles can be mounted on any standard 2 1/2”
(63.5) deep box. A feed-thru feature provides protection not only at that
receptacle but also at any other receptacle located downstream from it
on the same circuit.
These devices meet the requirements of The National Electric Code
and American Boat and Yacht Council Standard and will accept locking
fork terminals. Ground Fault Receptacles are also available for OEM
applications. Devices rated for 15A and 20A are available in brown,
ivory, gray and white. Consult factory for details.
CLOSE-UP
TERMINALS
Caution: Ground Fault Receptacles should not be mounted in
locations exposed to salt spray nor in the engine room. For GFCI
protection of such locations, downstream feeding from an
internally located Ground Fault Receptacle is recommended.
GFCI Receptacles and Surge Suppression Receptacles
Catalog Numbers
GF5252MA*
GF5252MIA*
GF5252MWA
GF5252MGYA*
CWP26CR
HBL5262ISA
Surge Suppression Receptacles 15A 125V AC Nominal. UL Listed at
400V Max. suppressed voltage.
Suitable for ANSI/IEEE C 62.41-installation categories “A” (outlets
and long branch circuits) and “B” (major feeders and short branch
circuits). The Hubbell Surge Suppression Receptacle helps protect
your electronic equipment from damage caused by transient
voltages. The receptacle contains metal oxide varisters which
dissipate the electrical energy of voltage spikes without interfering
with normal operations.
Dimensions in Inches (mm)
CWP26CR
GFCI and Surge Receptacles
Description
15A 125V brown GFCI duplex receptacle. Brown nylon
wall plate included.
Same as #GF5252MA except receptacle and plate are ivory.
Same as #GF5252MA except receptacle and plate are white.
Same as #GF5252MA except receptacle and plate are gray.
Gray PVC weatherproof lift cover plate for ground fault receptacles
(such as #GF5252MGYA) and Style Line® receptacles.
For vertical mounting in standard or FS/FD type boxes.
Ivory duplex surge suppression receptacle with power on
indicator light and damage-alert alarm beeper.
Note: *Not shown.
www.hubbell-wiring.com
HBL5262ISA
V-33
Marine Products
Marine Products
Receptacles
Inside the Boat
15 and 20 Ampere, 125V AC
Style Line® Receptacles
„ High-Impact nylon face resists breaking, chipping and cracking.
„ Will accept locking fork terminal to comply with ABYC standards.
„ Available in 4 colors for any decor with matching wall plates.
„ Smooth, high-gloss finish for rich appearance.
Style Line Series
Description
15A 125V AC brown duplex receptacle. See note.
Same as #HBL2132M except ivory. See note.
Same as #HBL2132M except white. See note.
Same as #HBL2132M except gray. See note.
HBL2132MI
Catalog Numbers
HBL2132M*
HBL2132MI
HBL2132MW*
HBL2132MGY*
Commercial Series
CRO15
HBL5251
CRO20I
Description
15A 125V AC brown duplex receptacle. See note.
Same as #CRO15 except gray. See note.
Same as #CRO15 except ivory. See note.
20A 125V brown duplex receptacle. See note.
Same as #CRO20 except black. See note.
Same as #CRO20 except gray. See note.
Same as #CRO20 except ivory. See note.
Same as #CRO20 except white. See note.
15A 125V brown single receptacle.
Same as #HBL5251 except ivory.
20A 125V brown single receptacle.
Same as #HBL5361 except ivory.
Catalog Numbers
CRO15
CRO15GRY*
CRO15I*
CRO20*
CRO20BLK*
CRO20GRY*
CRO20I
CRO20WHI*
HBL5251
HBL5251I*
HBL5361*
HBL5361I
Corrosion Resistant Series
Description
15A 125V yellow corrosion resistant duplex receptacle.
Use where salt or other corrosive elements are a problem.
Same as #HBL52CM62 except ivory.
Catalog Numbers
HBL52CM62*
HBL52CM62I
Special Application Series
Description
Catalog Number
Illuminated receptacle 15A 125V grounding. A high quality
HBL8200ILI
receptacle with something extra: an illuminated face. Ideal for use
in halls or as a gentle night light.
HBL52CM62I
Outlet Box
Description
Plastic switch/receptacle box. Measures 3 9/32” x 2 3/16” x 2 1/2”
(83.3 x 55.6 x 63.5) deep. For mounting in walls without studs. A
support strap is provided which pulls box tightly against back side
of wall. Not CSA.
Catalog Number
HBL6079
Receptacles
Note: Will accept locking fork terminal to comply with ABYC standards.
*Not shown.
V-34
www.hubbell-wiring.com
Dimensions in Inches (mm)
Switches & Weatherproof Switch Plates
P
15 and 20 Ampere, 120-277V AC
Commercial Series
Description
Single-pole toggle switch for controlling AC load from one
point, brown handle. See note.
Same as #CS115 except gray handle. See note.
Same as #CS115 except ivory handle. See note.
Same as #CS115 except office white handle. See note.
Same as #CS115 except white handle. See note.
Three-way toggle switch for controlling AC load from two points,
brown handle. See note.
Same as #CS315 except gray handle. See note.
Same as #CS315 except ivory handle. See note.
Same as #CS315 except office white handle. See note.
Same as #CS315 except white handle. See note.
Marine Products
Marine Products
Catalog Numbers
CS115*
CS115GY*
CS115I
CS115OW*
CS115W*
CS315*
CS115I
CS315GY*
CS315I*
CS315OW*
CS315W*
Special Application Series
Description
Catalog Numbers
20A 120V toggle switch with neon lamp set in ivory handle.
HBL1221IL
Handle illuminates when switch is in “OFF” position.
20A 120V three-way toggle switch with illuminated ivory handle for HBL1223IL*
controlling AC load from two points. Handle illuminates when “OFF.”
20A 120V single-pole toggle switch with neon lamp set in clear
HBL1221PL
red handle. Handle illuminates when switch is “ON.” Serves as
instant reminder that current is flowing to an appliance.
20A 120V three-way toggle switch for controlling AC load from two HBL1223PL*
points. Red handle illuminates when “ON.”
Single-pole PresSwitch® for controlling AC load from one point.
HBL1281
Switch activated brown button.
Same as #HBL1281 except ivory button.
HBL1281I*
Three-way PresSwitch® for controlling AC load from two points.
HBL1283†
Switch activated brown button.
Same as #HBL1283 except ivory button.
HBL1283I*†
Yellow neoprene weatherproof plate for use only with PresSwitches. HBL17CM50†
PresSwitch button is activated when bubble is pressed. Not CSA.
Clear silicone rubber weatherproof bubble plate for use with all
HBL1795
AC toggle switches and PresSwitches. Also ideal for use with
lighted handle toggle switches. Not CSA.
HBL1221IL
HBL1221PL
HBL1281
HBL1283
HBL17CM50
HBL1795
Outlet Box
Description
Plastic switch/receptacle box.
Measures 3 9/32” x 2 3/16” x 2 1/2” (83.3 x 55.6 x 63.5) deep.
For mounting in walls without studs. A support strap is provided
which pulls box tightly against back side of wall. Not CSA.
Note:
Catalog Number
HBL6079
Will accept locking fork terminal to comply with ABYC standards.
*Not shown.
†Not UL Listed.
Switches
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-35
Marine Products
Marine Products
Plugs an
Wall Plates, TV & Phone Plates
Inside the Boat
Color
Ivory
Gray
White
Brown
Ivory
Gray
White
Brown
Ivory
Gray
White
Brown
Ivory
Gray
White
Brown
Ivory
Gray
White
Brown
Ivory
Gray
White
Brown
Ivory
Gray
White
Brown
Gangs
One
One
One
One
Two
Two
Two
Two
One
One
One
One
Two
Two
Two
Two
One
One
One
One
Two
Two
Two
Two
One
One
One
One
Smooth Nylon
Standard
Mid-Size
Series
Series
P1
PJ1
P1G
–
P1W
PJ1W
P1X
PJ1X
P2
PJ2
P2G
–
P2W
PJ2W
P2X
PJ2X
P8
PJ8
P8G
–
P8W
PJ8W
P8X
PJ8X
P82
PJ82
P82G
–
P82W
PJ82W
P82X
PJ82X
HPS1I
PJ26
HPS1G
PJ26G
HPS1WA
–
HPS1
PJ26X
HPS2I
PJ262
HPS2G
–
HPS2WA
–
HPS2
PJ262X
P7
PJ7
P7G
–
P7W
PJ7W
P7X
PJ7X
Ivory
Gray
White
Brown
Two
Two
Two
Two
P18
P18G
P18W
P18X
PJ18
–
PJ18W
PJ18X
Ivory
White
Brown
Two
Two
Two
–
–
–
PJ126
–
PJ126WA –
PJ126X
–
S126
–
–
Ivory
Gray
White
Brown
One
One
One
One
P14
P14G
P14W
P14X
–
–
–
–
–
–
–
–
S13
–
–
–
6 Conductor
Telephone Jack.
Ivory
Brown
One
One
–
–
PJ216
PJ216X
–
–
–
–
TV plate with
RG59 Connector.
Ivory
One
–
PJ212
–
–
P2
P1
P1
P2
P82
P8
P82
HSP1
HSP2
HPS1
HPS2
Smooth Metal
Stainless
Brass
Steel
B1
S1
–
–
–
–
–
–
B2
S2
–
–
–
–
–
–
B8
S8
–
–
–
–
–
–
B82
S82
–
–
–
–
–
–
B26
S26
–
–
–
–
–
–
B262
S262
–
–
–
–
–
–
B7
S7
–
–
–
–
–
–
B18
–
–
–
P7P7
S18
–
–
–
P18P18
PJ126
Wall Plates
P14
P14
PJ216
PJ212 (Not CSA)
V-36
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
Communication Frames and Connectors
Hubbell now offers the ability to put 2 or 3 communication devices in a single,
Style Line® plate.
Any combination of phone (6-position jack), cable TV (F-type connector) and Category 5e modular data jacks can be
assembled onto a 2-port or 3-port frame - each sold individually so you can customize them how you need them - or - the
highly popular phone & cable TV combination is available with the frame and matching wall plate under a single catalog
number - in all the popular colors.
Finally - a single communications plate that can take the place of 2 or 3 plates - available from a company you can trust
for superior quality.
Hubbell’s Marine communication frames and connectors deliver high quality data and multimedia transmission to the
point of connection. Hubbell’s 2 and 3 port Styleline frames and leading edge connections allow for customized
configurations. Install Hubbell’s Marine communication offering and be assured a reliable connection.
2 Port Communication Frame, Fully Loaded
(6-Position Phone Jack, F-Type Cable TV Jack and
Style Line Plate Included)
Color
# of Ports
Connection Type
Catalog Numbers
White
2
USOC - F Type
FC26FW
Ivory
2
USOC - F Type
FC26FI
Black
2
USOC - F Type
FC26FBK
Gray
2
USOC - F Type
FC26FGY
Styleline Frames, 2 Port and 3 Port Unloaded
Color
# of Ports
Connection Type
Catalog Numbers
White
2
-
FCX244W
Ivory
2
-
FCX244I
Black
2
-
FCX244BK
Gray
White
Ivory
Black
Gray
2
3
3
3
3
-
FCX244GY
FCX344W
FCX344I
FCX344BK
FCX344GY
FC26FGY
Style Line Frame, Loaded
Styleline 2-port Unloaded Frames
Color
Wiring
No. Positions
Catalog Numbers
White
T568A/T568B
8-Positions
HBL5EW
Ivory
Black
Gray
T568A/T568B
T568A/T568B
T568A/T568B
8-Positions
8-Positions
8-Positions
HBL5ETI
HBL5EBK
HBL5EGY
USOC Modular Keystone Jacks
Color
Wiring
No. Positions
Catalog Numbers
White
USOC
6-Positions
HBLUW
Ivory
Black
Gray
USOC
USOC
USOC
6-Positions
6-Positions
6-Positions
HBLUTI
HBLUBK
HBLUGY
Communication Frames and Connectors
Category 5e Modular Keystone Jacks
Styleline 3-port Unloaded Frames
Category 5e Jacks
USOC 6-Position Jacks
F Type Connector Keystone
Color
Catalog Numbers
White
SIFW
Ivory
Black
Gray
SIFI
SIFBK
SIFGY
F Type Connector
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-37
Marine Products
Marine Products
Panel Mount Toggle & Rocker Switches
12 Volt DC
KEY
CHART
M11SP
1. Toggle switch
Fits panels up to 1/4” thick
when not using the
back-up nut provided; fits
panels up to 3/16” thick
when using the back-up
nut. Requires a 1/2”
mounting hole.
M11SP
M123SP
M21SP
M11LRGSP
2. Lighted toggle switch
Built-in pilot light
(R=red, G=green) for
night vision. Same panel
specs as #1.
M11LTR
3. Lighted-tip toggle switch
Red pilot light visible in
tip of toggle only. Same
panel specs as #1.
Typical Applications
Lights, bilge blower, bilge
pump(s), accessories
Description
Single pole, single throw.
On/Off.
Horn, starter, winches,
gauges
Single pole, single throw.
Momentary On/Off.
Bilge pumps, speed selector,
lights, navigation lights
Single pole, double throw.
On/Off/On.
Bilge pumps
Single pole, double throw.
Momentary On/Off/On.
Single pole, double throw.
Momentary On/Off/Momentary On.
Double pole, single throw.
On/Off.
Double pole, double throw.
On/Off/On.
Trim Tabs
Lights, accessories
M223SP
Navigation lights, wipers,
dual fuel tanks
Navigation lights, windlass
12 Volt DC Rated Switches
MSB1
MR11SP
4. Rocker switch
Requires a 11/2” high x 7/8”
wide rectangular
opening.
Winches, trim tabs,
dual fuel tanks
Provides positive seal against
moisture, oil, etc. Fits any
non-lighted toggle switch.
For remote operation of horn.
MH11
Fits MH11 horn switch.
Note: *Not shown.
Double pole, double throw.
On/Off/On (with jumper).
Double pole, double throw.
Momentary On/Off/Momentary On.
Black silicone rubber boot bonded
to brass nut.
MR123LRSP
5. Lighted rocker switch
Built-in pilot light for
night vision. Same panel
specs as #4.
Catalog Numbers
M11SP
M11LRSP*
M11LRGSP
M11LTR
MR11SP
MR11LRSP*
M11MSP*
M11LTRM*
MR11MSP*
M123SP
M123LTR*
MR123SP*
MR123LRSP
M123MSP*
MR123MSP*
M123MMSP*
MR123MMSP*
M21SP
MR21SP*
M223SP
MR223SP*
MR223LRSP*
M223JSP*
Key
1
2
2
3
4
5
1
3
4
1
3
4
5
1
4
1
4
1
4
1
4
5
1
M223MMSP*
MR223MMSP*
MSB1
1
4
Pushbutton horn switch with 15/32”
MH11
long nickel plated brass mounting stem.
Terminals are .250” spade.
Black pushbutton (horn) boot.
MHB11
MHB11
V-38
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
30A, 28V DC
Electric Fishing Reel Devices
Electric Fishing Reel Devices
Hubbell has a DC rated electrical system designed specifically for
larger electric fishing reel systems.
Up until now, larger electric fishing reel systems typically utilized 30
Amp AC rated corrosion resistant devices since there were no DC
rated devices.
The system features a corrosion resistant plug, connector body and
receptacle and can be used along with a Hubbell outlet box and
weatherproof cover plate to complete the installation. These devices
are all rated at 28 volts DC and are applicable for all 12, 24 and 32
volt DC fishing reel systems. The devices are UL listed and CSA
certified. All devices are made of high-visibility yellow nylon that is
impact resistant and U. V. stabilized for longer life. Also, the contacts
are nickel plated for corrosion resistance.
HBL328DCR
Electric Fishing Reel Devices
Description
Yellow, locking single receptacle
with abuse-resistant face.
Can be mounted in Hubbell box
#HBL6080 and used with #HBL74CM25WOA
weatherproof plate.
Yellow, locking plug has rugged nylon
housing and rear dust seal to keep
dust and foreign matter out.
Yellow, locking connector body has
rugged, nylon housing and rear dust
seal to keep dust and foreign matter out.
Catalog Numbers
HBL328DCR
HBL328DCP
HBL328DCP
HBL328DCC
Accessories
Description
Black phenolic type FD (deep) weatherproof box has two
3
/4” (19.1) I.P.S. molded-in knockouts. 4 9/16”H x 2 15/16”W x 3 1/4”D
(115.9H x 74.6W x 82.6D) and has 22 cubic inch capacity.
Spring-loaded lift cover plate, for weatherproofing
#HBL328DCR outlet. White in color.
Same as #HBL74CM25WOAW except yellow in color.
Catalog Numbers
HBL6080
HBL328DCC
HBL74CM25WOAW
HBL74CM25WOA
Electric Fishing Reel Devices
HBL6080
HBL7425WOA
HBL74CM25WOA
HBL74CM25WOAW
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-39
Marine Products
Marine Products
IP66
Boatyard Accessory Items
SUITABILITY
Enclosures Only
Marine Grade Outlet Box Hoods
3.00"
(76.20 )
5.19"
(131.83)
WP826MHP
3.00"
(76.20 )
6.13"
(155.70)
3.38"
(85.85)
WP826MP
HBL6085
HBL6085
Accessories
Catalog Numbers
Cast aluminum outlet box hood: for duplex receptacles,
vertical mount.
WP8M
Cast aluminum outlet box hood; for GFCI/Style Line receptacle;
vertical mount.
WP26M
Same as #WP8M except horizontal mount.
WP8MH
Same as #WP26M except horizontal mount.
WP26MH
Cast aluminum outlet box hood; for 15A & 20A single straight blade
receptacles; vertical mount.
WP7D
Cast aluminum outlet box hood; for 20A & 30A single locking
receptacles; vertical mount.
WP723D
Non-metallic outlet box hood; for duplex, GFCI and Style Line®
receptacles; vertical mount.
WP826MP
Same as #WP826MP except horizontal mount.
WP826MHP
Metallic
• Die cast Alloy 360 copper-free
aluminum for maximum corrosion
resistance and durability. Alloy 360 has
less than .004% copper content.
• Finish is baked aluminum lacquer.
Non-metallic
• Impact resistant polycarbonate, an
extremely durable thermoplastic.
4.31"
(109.47)
HBL10CM22S
V-40
Description
• Transparent cover provides visibility to
the connection.
ALL
• NEMA 3R rating when used with the
appropriate weatherproof outlet box
which is intended for outdoor use
primarily to provide a degree of
protection against rain, sleet, and
damage from external ice formation.
• Box or device mount for flexibility of
installation.
• Gaskets are closed-cell foam.
• Meets OSHA lockout/tagout
requirements.
• Latching covers hold securely.
• Large cord openings.
• Clearly marked UL and CSA logos.
• Covers include gasket and mounting
screws. Lids have gasketless design.
• UL Listed/CSA Certified.
• Devices not included.
• Holes for padlocks are 1 /4” (6.4 dia.).
• Drill points in four corners for box
mounting.
Nylon Watertight Strain Relief Cord Connectors
These Hubbell nylon cord connectors provide strain relief and a
watertight seal where cable enters a piece of equipment, panel, or
box. A patented GOTCHA® ring, with a split and hinge design, allows
for better adjustment to the cord as the connector nut is tightened,
providing superior cord gripping compared to other types. A soft
neoprene bushing compresses to keep liquids out and allows the nut
to be easily tightened.
Description
A gray male PVC adapter with 3/4” N.P.T. pipe thread for adapting
PVC conduit to FS and FD boxes with 3/4” N.P.T. hub (#HBL6080,
#HBL6080OS, #HBL60CM83). Not UL Listed.
Straight nylon cord connector, N.P.T. hub size 1/2”, diameter range
.250”-.375” (6.4-9.5).
Straight nylon cord connector, N.P.T. hub size 1/2”, diameter range
.375”-.500” (9.5-12.7).
Straight nylon cord connector, N.P.T. hub size 3/4”, diameter range
.375”-.500” (9.5-12.7).
Straight nylon cord connector, N.P.T. hub size 3/4”, diameter range
.500”-.625” (12.7-15.9).
Straight nylon cord connector, N.P.T. hub size 3/4”, diameter range
.625”-.750” (15.9-19.1).
Straight nylon cord connector, N.P.T. hub size 1”, diameter range
.625”-.750” (15.9-19.1).
* Not shown.
www.hubbell-wiring.com
Catalog Numbers
HBL6085
HBL10CM22S
HBL10CM23S*
HBL10CM35S*
HBL10CM36S*
HBL10CM37S*
HBL10CM41S*
Dimensions in Inches (mm)
Marine Products
Marine Products
Boatyard Accessory Items
Non-Metallic Vaportight Incandescent Fixtures
These non-metallic, vaportight incandescent fixtures offer long life and
trouble-free lighting in wet locations in marinas and on boats. Some
features of these new units are:
• UV resistant, gray, glass filled thermoplastic polyester box, mounting
adapters and globe guards resists abuse and harmful effects of the elements.
• Excellent temperature operating range of -40°F ( -40°C) to +302°F (150°C)
for use in areas with wide temperature variations or extreme ambient
temperatures.
• High temperature silicone gasketing maintains integrity and molded
threads for ease of installation/removal.
• Heat resistant glass globe withstands thermal shock in wet locations and
has thread type mounting to assure weathertight sealing.
• High strength protective globe guard helps prevent accidental globe and
lamp breakage.
• Accommodates Type A incandescent lamps up to 150 watts.
• U.L. listed including UL1571 (Incandescent Fixtures and Fixture Fittings)
and UL 595 (Marine Type Miscellaneous Fixtures).
NVA15GHG
NVB
Lighting and Lighting Fixtures
Description
Ceiling mount non-metallic, vaportight incandescent luminarie
including the fixture, mounting box, guard and heat resistant
glass globe. Accepts up to 150 watt Type A incandescent
lamp (not included).
Wall mount bracket only to adapt #NVX15GHG ceiling mount
fixture to a wall mount fixture. Order #NVB and #NVX15GHG
to get wall mount fixture.
Pendant mount non-metallic, vaportight incandescent luminarie
including fixture, mounting cap, guard and heat resistant glass
globe. Accepts up to 150 watt Type A incandescent lamp
(not included).
Replacement guard to #NVX15GHG and #NVA15GHG.
Heat resistant replacement globe for #NVX15GHG and
#NVA15GHG. Made of tempered glass.
Note: *Not shown
Catalog Numbers
NVX15GHG*
NVB
NVA15GHG
NVG*
VCGP100*
Lighting Products
Dimensions in Inches (mm)
www.hubbell-wiring.com
V-41
Marine Products
Marine Products
Marine Grade Dockside Boxes & Covers
Marine Grade Dockside Boxes & Covers
HBL6080
HBL60CM83
Description
Catalog Numbers
Black phenolic type FD (deep) weatherproof box has two
HBL6080
3
/4” (19.1) I.P.S. molded-in knockouts. 4 9/16”H x 2 15/16”W x 3 1/4”D
(115.9H x 74.6W x 82.6D) and has 22 cubic inch capacity.
Yellow fiberglass type FD (deep) weatherproof box has two 3/4”
HBL60CM83
(19.1) I.P.S. molded-in knockouts. 4 9/16” H x 2 15/16”W x 3 1/4”D
(115.9H x 74.6W x 82.6D) and has 22 cubic inch capacity.
Yellow fiberglass type FD box same as #HBL60CM83 - except
HBL60CM84
has two 1” (25.4) I.P.S. molded-in knockouts.
Black phenolic type FS (shallow) weatherproof box has two 3/4”
HBL6080OS
(19.1) I.P.S. molded-in knockouts. 4 9/18”H x 2 15/16”W x 2 3/16”D
(115.9H x 74.6W x 55.6D) and has 16 cubic inch capacity.
Black non-metallic FS box with 3/4” threaded hubs used for
PH6619
mounting phone and TV outlets and #PH6595 recreational vehicle
inlet (see #PH6621 for mounting box on recreational vehicle).
Cord connector included for strain relief and to maintain watertight
integrity of box when cable is used. PVC adapter also included for
connection of PVC conduit to box.
Black phenolic junction box with four 3/4” (19.1) I.P.S. molded-in
HBL6081
knock-outs. Has 4 1/8” (104.8) diameter and is 1 7/8” (47.6) deep.
Phenolic blank cover, 1/4” (6.4) thick, for #HBL6081 box.
HBL6082
Black phenolic black cover plate for #HBL6080OS.
HBL6087
Yellow Valox® blank cover plate for use with FS and FD
HBL60CM88
type boxes.
Note: Valox ® is a registered trademark of General Electric Company.
HBL60CM84
HBL6080OS
HBL6081
Boxes and Covers
HBL6087
HBL60CM88
PH6619
HBL6082
V-42
www.hubbell-wiring.com
Dimensions in Inches (mm)
Marine Products
Marine Products
Marine Grade Lift Cover Plates
Marine Grade Weatherproof Plates
Description
Yellow Valox® spring-loaded lift cover plate for weatherproofing
duplex receptacles. Stainless steel screws and neoprene gasket
included for mounting to FS/FD type weatherproof boxes.
IP20 SUITABILITY.
Same as #HBL52CM21 except white in color.IP20 SUITABILITY.
Same as #HBL52CM21 except gray in color. IP20 SUITABILITY.
Same as #HBL52CM21 except for mounting to standard boxes.
IP20 SUITABILITY.
Same as #HBL52CM22 except gray in color. IP20 SUITABILITY.
Yellow Valox® spring-loaded lift cover plate for weatherproofing
single straight blade receptacles. Stainless steel screws and
neoprene gasket included. For mounting to FS/FD type
weatherproof boxes. IP44 SUITABILITY.
Same as #HBL74CM23WO except gray in color.
IP44 SUITABILITY.
Yellow Valox® spring-loaded lift cover plate for weatherproofing
old style #26CM10 receptacle. Meets the most stringent
requirements of UL’s three listing categories for weatherproof
plates. Stainless steel screws and neoprene gasket included for
mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY.
Same as #HBL74CM24WO except gray in color. IP44 SUITABILITY.
Yellow Valox® spring-loaded lift cover plate for weatherproofing
#HBL26CM10 receptacle. Meets the most stringent requirements
of UL’s three listing categories for weatherproof plates. Stainless
steel screws and neoprene gasket included for mounting to
FS/FD type weatherproof boxes. IP44 SUITABILITY.
Same as #HBL74CM25WOA except white in color.
IP44 SUITABILITY.
Same as #HBL74CM25WOA except gray in color. IP44 SUITABILITY.
Yellow Valox® lift cover plate for weatherproofing 50A receptacles.
Meets requirements of the most stringent of UL’s three listing
categories for weatherproof plates. Stainless steel screws and
a neoprene gasket included. For mounting to FS/FD type
weatherproof boxes. IP44 SUITABILITY.
Same as #HBL77CM74WO except gray in color. IP44 SUITABILITY.
Note: *Not shown.
Catalog Numbers
HBL52CM21
HBL52CM21W
HBL5221*
HBL52CM21
HBL52CM22*
HBL5222*
HBL74CM23WO
HBL7423WO*
HBL74CM23WO
HBL74CM24WO
HBL74CM25WOA
HBL74CM24WO
HBL7424WO*
HBL74CM25WOA
HBL77CM74WO
HBL74CM25WOAW
HBL7425WOA*
HBL77CM74WO
CWP1CR
HBL7774WO*
Commercial Grade Weatherproof Plates
Available in a host of configurations – Twist-Lock® and straight blade
receptacles in single or duplex as well as switches – these plates are
perfect for marine use. The PVC resists deterioration over time and
has high tensile and impact strength. Each plate comes with a tightly
sealing, rubberized gasket and a super strong lift cover spring.
CWP8CR
Description
Catalog Numbers
Gray PVC weatherproof lift cover plate for toggle switches (such CWP1CR
as #CS115). For vertical mounting in standard or FS/FD
type boxes.
Gray PVC weatherproof lift cover plate for duplex receptacles
CWP8CR
(such as #HBL52CM62). For vertical mounting in standard or
FS/FD type boxes.
Gray PVC weatherproof lift cover plate for ground fault receptacles CWP26CR
(such as #GF5252MGYA) and Style Line® receptacles. For vertical
mounting in standard or FS/FD type boxes.
Note: Valox ® is a registered trademark of General Electric Company.
Dimensions in Inches (mm)
www.hubbell-wiring.com
CWP26CR
V-43
Weatherproof Plates
Commercial Grade Weatherproof Plates
Marine Products
Marine Products
Electrical Standards
ABYC Standard, July 2001, Excerpts.
not be interchangeable with receptacles and matching plugs used
on DC systems.
8.4 DEFINITIONS – For the purposes of this standard, the
following definitions apply.
8.17.4 Power wiring for receptacles shall be connected so that the
grounded (white) conductor attaches to the terminal identified by
the word “white” or a light color (normally white or silver). The
ungrounded conductors(s) shall be attached to the terminal(s)
identified by a dark color (normally brass or copper) and, optionally,
the letters X, Y, and Z or L1, L2, and L3.
Ground fault circuit interrupter (GFCI) – A device intended for the protection
of personnel that functions to de-energize a circuit, or portion thereof, within
an established period of time when a current to ground exceeds some
predetermined value that is less than that required to operate the
overcurrent protective device of the supply circuit.
Watertight – So constructed that water will not enter the enclosure
under the test conditions specified in NEMA standard 250.
Weatherproof – constructed or protected so that exposure to the
weather will not interfere with successful operation.
8.17.5 A branch circuit supplying a combination of receptacle
loads and permanently connected loads shall not supply fixed loads
in excess of the following:
8.17.5.1
600 watts for a 15 ampere circuit;
8.17.5.2
1000 watts for a 20 ampere circuit.
NOTE:
8.12 GROUND FAULT PROTECTION
8.12.1 If installed, a ground fault protector (GFP) shall only be
used to protect equipment.
8.17.6 Receptacles shall be installed in locations not normally
subject to rain, spray, or flooding, but, if receptacles are used in
such areas, the following shall apply:
NOTE: A ground fault circuit interrupter (GFCI) may be used on single phase
AC circuits to provide additional protection for personnel and
equipment.
8.17.6.1 Receptacles installed in locations subject to rain, spray,
or splash shall be weatherproof as may be provided by a spring
loaded, self closing cover.
8.12.2 GFCI and GFP breakers shall meet the requirements of
Underwriters Laboratories standard UL 943, Ground Fault Circuit
Interrupters, and the requirements of UL 489, Molded Case Circuit
Protectors for Circuit Breaker Enclosures.
8.17.6.2 Receptacles installed in areas subject to flooding or
momentary submersion shall be of a watertight design as may be
provided by a threaded, gasketed cover.
8.12.3 GFCI and GFP breakers may be installed as panelboard
feeder breakers to protect all associated circuits or in individual
branch circuits.
8.17.7 Receptacles provided for the galley shall be located so
appliance cords can be plugged in without crossing a traffic area,
galley stove, or sink.
8.12.4.1 the single phase 120 volt system has a polarity indicator,
or
8.17.8 If installed in a head, galley, machinery space, or on a
weather deck, the receptacle shall be protected by a Type A
(nominal 4-6 milliamperes) Ground Fault Circuit Interrupter (GFCI).
See ABYC E-8.12.
8.12.4.2 the system uses either a polarization transformer, or
NOTE:
8.12.4 Single-pole GFCI and GFP breakers shall only be used if:
the system is 120/240 volts.
8.12.5 GFCI receptacle devices shall meet the requirements of
Underwriters Laboratories standard UL 943, Ground Fault circuit
Interrupters, and the requirements of UL 498, Electrical Attachment
Plugs and Receptacles.
8.12.6 GFCI receptacle devices may be installed as part of a
convenience outlet installation either in single outlet applications or
in multiple feed through installations. See ABYC E-8.17.8.
NOTE:
Isolation transformer primary main breakers – GFP breakers may be
installed as the main breaker on the primary side of isolation
transformers. See E-8.23, Diagram 8 and Diagram 11. This GFP
breaker will provide ground fault protection only for the primary
winding of the transformer. Protection for circuits supplied by the
secondary winding of the transformer may be provided in
accordance with ABYC E-8.11.4, E-8.11.5, E-8.11.6.3, and E-8.12.4.
8.16 SWITCHES
8.16.1 Switches used in branch circuits shall simultaneously open
all ungrounded conductor(s) of the branch circuit.
Codes and Standards
Refer to E-8.18.5 for load calculations.
8.16.2 Switches shall have voltage ratings not less than the
system voltage, current ratings not less than the connected load,
and shall be rated for the type of load, i.e., inductive or resistive.
8.17 RECEPTACLES
8.17.1 Receptacles shall be installed in boxes that meet the
requirements of UL 514A, Metallic Outlet Boxes, or 514C,
Nonmetallic Outlet Boxes, Flush Device Boxes and Covers 514.D
Cover plates for flush mounted wiring devices.
8.17.2 Receptacles shall be of the grounding type with a terminal
provided for the grounding (green) conductor as shown in Figure 10
and Figure 11.
GFCI receptacle devices are not necessarily ignition protected per
ABYC E-8.9.1.
8.22 SHORE POWER SUPPLY
8.22.1 Power Inlet – The receptacle, or receptacles, installed to
receive a connecting cable to carry AC shore power aboard shall
be a male type connector.
8.22.1.1 Power inlets installed in locations subject to rain, spray,
or splash shall be weatherproof whether or not in use.
8.22.1.2 Power inlets installed in areas subject to flooding or
momentary submersion shall be of a watertight design whether or
not in use.
8.22.1.3 Metallic power inlets installed on metallic boats using an
isolation transformer or a galvanic isolator shall be insulated from
metallic structure and components. On nonmetallic boats using an
isolation transformer or a galvanic isolator the power inlet shall be
insulated from metallic components connected to the boat’s ground.
8.22.2 Shore Power Cable – On each boat equipped with an AC
shore power system, a shore power cable that contains the
conductors for the power circuit and a grounding (green) conductor
shall be provided.
8.22.2.1 Except where the shore power cable is permanently
connected to the boat, the boat end of this cable shall be
terminated with a locking and grounding female type connector to
match the boat power inlet. See Figure 11 and Figure 12.
8.22.2.2 The shore power cable shall be flexible cord with the
minimum properties of Type SO, ST, STO, SEO, or STOOW, and
shall be suitable for outdoor use. The shore connection end of this
cable shall be fitted with a locking and grounding type plug with the
required number of poles and shall comply with the National
Electrical Code. See Figure 11 or Figure 12 and Appendix AP Table
2.
8.17.3 Receptacles and matching plugs used on AC systems shall
V-44
www.hubbell-wiring.com
Dimensions in Inches (mm)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement