multifunction steamer let`s get started.

multifunction steamer let`s get started.
Steam
MULTIFUNCTION STEAMER
LET’S GET STARTED.
S85-CM
SCSMV1SG
Let’s talk safety
Basic
safety
precautions
Don’ts
Do’s
This STEAMER is intended for household use only and NOT
for commercial or industrial use.
CAUTION: Danger of scalding
•Only use the steamer indoors and keep the area you’re
cleaning well lit.
•Keep fingers, hair and loose clothing away from moving parts
and openings whilst using the steamer.
•This steamer can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the steamer. Cleaning and user maintenance
shall not be performed by children without supervision.
•Please refer to floor manufacturer’s care recommendations before use, and
test your flooring/carpet/rugs by running the steamer over a small hidden
area, if no pile distortion or no damage occurs continue cleaning. Not suitable
for use on wax polished floors or furniture, acrylic surfaces and synthetic,
velvet or steam/water sensitive materials.
•This steamer should not be used to clean electrical appliances such as
microwaves, televisions and electrical heating systems etc.
•Only Vax recommended cloths and accessories should be used with
this steamer. This steamer is a water only product, using detergents will
invalidate the guarantee.
•Don’t touch any hot areas/accessories on your steamer.
It’s normal for the steamer and accessories to heat up during
use, always allow them to cool down before handling.
•Don’t use the steamer if it has been dropped, damaged,
immersed in water or left outdoors.
•Don’t run over the power cord or use steamer if the power
cord or plug is damaged. Please contact our Customer Care
Line on 0330 026 8455 (Mon-Fri 8:30am to 6:30pm
Sat 9:00am to 5:00pm).
•Don’t handle the plug or use the steamer with wet hands.
Don’t pull or carry the steamer by the power cord.
•Don’t use the power cord as a handle, don’t pull the power cord around
corners or sharp edges or close a door over the power cord. Don’t unplug
the steamer by pulling on the power cord.
•Don’t attempt to remove blockages with sharp objects as this may cause
damage to the steamer, remove blockages only as instructed in this guide.
•Don’t aim the steamer at people, animals, plants and electrical components
or wires. Never touch the steam jet (there is a risk of scalding).
•Don’t use the steamer with incorrect voltage as this may result in damage
or injury to the user. The correct voltage is listed on the ratings label.
•Don’t use the steamer to clean or refresh any items of clothing that are still
being worn on the body.
•Don’t leave the steamer turned on when unattended.
•Always fill the water tank with water only. Never add perfume,
stain remover or products containing alcohol. Filling the water
tank with hot or boiling water will damage the steamer and
invalidate the guarantee.
•Always vacuum your carpets thoroughly and ensure hard floor
areas are free from grit and debris before using your steamer.
•Always unplug the steamer and allow to cool before carrying
out any maintenance.
•Turn off all controls on the steamer before disconnecting or
connecting the power cord, after use always wrap the power
cord around the cord clips.
•Take extra care when cleaning on the stairs.
•Always replace the fuse in the plug with a British 13amp fuse. Always protect
the power cord from heated surfaces and open flames.
•Use only CE approved 13amp extension cords, non-approved extension cords
can overheat. Care should be taken to arrange the extension cord as it could
be a trip hazard.
•Store the steamer in a cool, dry area away from children. Before storing the
steamer please make sure the water tank is thouroughly clean and empty.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY
AS INSTRUCTED IN THIS GUIDE.
Thank you for buying this Steam product
Contents
Let’s talk safety
Taking care of your sealed hard floors and surfaces
Vax Steam products are designed to make steam cleaning your hard floors and surfaces
regularly, as effective and efficient as possible, and this user guide will help you get the most
out of your machine.
Maintaining your hard floors and surfaces with our Steam products will ensure they
keep looking beautiful and are hygienically clean.
Taking care of your Multifunction Steamer
Also inside this guide are instructions on maintaining your new machine, so that
it’s always ready when you are to tackle your hard floors and surfaces.
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can be found online at: vax.co.uk/support
Let us know what you think @VaxUK
Steam Clean Multi
and Steam Glide
Included with
your machine
Getting to know your machine
Measuring Jug
Getting started
Concentration Nozzle
Using your machine
Squeegee
Taking care of your machine
Small Round Brush
Let’s talk technical
Grout Brush
What to do if it goes wrong
Utility Head
Getting in touch
Utility Head Pad
Accessories
Microfibre Pad
Notes
Carpet Glider
Getting to know your machine
Handle
Getting started
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Before you Begin
Quick release cord hook
CAUTION
• The steamer and accessories get very hot during use, always allow them to cool down before handling.
• Always unplug and switch off the steamer when assembling or disassembling.
• Always switch off the steamer before emptying the water tank or changing the cloths/accessories.
IMPORTANT
• Please refer to floor manufacturer’s care recommendations before use and test the steamer on a hidden area of flooring
to begin with.
• Test for colour fastness in a small hidden area of upholstery/fabric to check for colour removal before use.
• When using the steamer, basic safety precautions should always be observed.
• Don’t aim the steamer at people, animals, plants and electrical components or wires. Never touch the steam jet or floorhead
from a short distance (there is a risk of scalding).
• The steamer is equipped with a thermostat and a thermal cut-out. If for any reason the steamer overheats it will switch off.
If this happens turn off and unplug the steamer, allow to cool for at least 2 to 4 hours and re-try.
• Don’t use hot or boiling water to fill or clean water tank.
Handle release button
Quick release cord hook
Handheld handle
Assembling your steamer
Handheld steam trigger (hidden)
On / off & steam control dial
Power on indicator
Water tank cap
Water tank (Part of unit)
Accessory floorhead
release button
Floorhead
Carpet Glider
Push the main body down into the
floorhead until it clicks into place.
Technical Specification
Accessories & Consumables
Name Steam Clean Multi S85-CM
Name Steam Glide SCSMV1SG
Voltage 220-240v˜50Hz
Voltage 220-240v˜50Hz
Wattage 1300w
Wattage 1300w
Cord length 5m
Cord length 5m
Weight 2.5kg
Weight 2.5kg
Microfibre Pads (Type 1)
1-1-131448-00
Pro Cleaning Pads (Type 6)
1-1-132319-01
Coral Cleaning Pads (Type 3)
1-1-131643-00
Carpet Glider (Type 3)
1-1-133527-00
Subject to technical change without notice.
*To purchase consumables and accessories, please visit vax.co.uk
Push the handle into main body until it
clicks into place. The collar should be gripped
when connecting or releasing the handle.
Stand the steamer upright by pushing the
main body forward to lock into position.
Using your machine
Using your machine
IMPORTANT: When using on carpets, always make sure the Microfibre Pad is used and covers the floorhead entirely before
using the Carpet Glider. Only use the Carpet Glider when refreshing carpets.
IMPORTANT
• Never turn the steamer over when water is in the tank, as some water may leak through the air valve.
It is normal for the water tube to make a rattling sound inside the water tank during use.
Refreshing carpets
Filling water tank
Correct
Incorrect
Remove floorhead and handle
and place steamer on flat
surface. Twist water tank
cap anticlockwise and lift
to remove.
Do not fill directly from tap
or over sink. Keep steamer
on flat surface. Use the
Measuring Jug and fill the
tank with 330ml (2 x 165ml)
of water.
Replace cap, align tabs
and twist clockwise
to tighten.
The water tank cap
has lock and unlock
padlock symbols.
P
TI
Place the Microfibre Pad on
the floor white side facing
up. Place steamer onto pad
making sure the entire pad
covers the floorhead.
With Microfibre Pad
attached, push steamer
into front of the Carpet
Glider, then place back
of the floorhead into the
clip. The Carpet Glider
should only be used
when refreshing carpets.
Plug into mains, turn dial to
‘ON’ position, the red light will
illuminate to indicate power on.
There will be no sounds for
the first 30 seconds whilst it is
heating up.
Place your foot on
floorhead and pull handle
backwards to recline.
Move the steamer slowly
backwards and forwards
across the carpet paying
particular attention to high
traffic areas.
To release the Carpet Glider,
place your foot on clip and
push down. Lift steamer
to remove.
Cleaning hard floors
Twist the steam control dial
to desired setting.
Steam is activated automatically.
Take care when changing
settings during cleaning.
IMPORTANT
• Never use the steamer without a Microfibre Pad attached to the floorhead.
• Never leave the steamer on one spot for an extended period of time or with a damp or wet Microfibre Pad attached as this
may damage the floor surface.
Place the Microfibre Pad on the
floor white side facing up. Place the
floorhead onto Microfibre Pad making
sure the Microfibre Pad covers the
entire floorhead.
Place foot onto the floorhead and
pull handle backwards to recline.
Plug into mains, turn dial to ‘ON’; the red
light will illuminate to indicate power on. The
steamer will be ready after approximately 30
seconds. There will be no sounds for the first
30 seconds whilst it is heating up.
Move the steamer slowly backwards
and forwards across the floor paying
particular attention to high traffic areas.
To steam your floors twist the steam
control dial to desired setting. Steam
is activated automatically. Take
care when changing settings
during cleaning.
Turn dial to ‘OFF’ position and allow
steamer to cool, the amber light will
switch off. Hold corner of pad down with
your foot and lift steamer to peel away.
Switch OFF and allow
to cool first. Steam is
automatic in stick
mop mode.
CAUTION
Using your machine
Using your machine
IMPORTANT: The handheld is to be used with water only, putting detergent into the water tank can cause damage.
Always check the tools are clean and free from debris, don’t use if damaged, broken or worn.
CAUTION: Never use the Squeegee on cold glass/windows as it may cause damage.
Attaching accessories
Using the machine as a handheld
Attaching brushes
Push handle release button and lift
handle to remove. The collar should be
gripped with one hand when releasing
the handle with the other hand.
Press accessory release button and lift
steamer to release floorhead.
Push Concentration Nozzle into steamer
until it clicks into place.
Small tools can be attached via the
Concentration Nozzle. Push together to
click into position and secure. Push hard
and ensure click is heard. Add pull test on
brushes to check tools are secure.
Attaching Utility Head
Stretch utility pad over
Utility Head.
Push Utility Head and pad into steamer until
secure. It will not lock into place. Pull test
to check it is secure.
Attaching Squeegee
Plug into mains, turn the dial to ‘on’
position. The red light will illuminate to
indicate power on.
Twist the steam control dial to
desired setting.
Align the tab on the Squeegee with the Utility
Head and utility pad, push together to lock into
position. Please note that the utility pad must
be attached to the Utility Head before the
Squeegee can be fitted on. Squeegee will
not connect without the pad on first.
After attaching your
chosen accessory
gently pull to make
sure it’s locked into
place or feels secure.
Always switch OFF the
steamer before attaching
the concentration tool
and accessories.
To produce steam squeeze the trigger in short bursts. Don’t hold the trigger
continuously to prevent over wetting. Allow 30 seconds for steamer to
warm up. No sound will be heard until trigger is pressed. No steam will be
visible until after 30 seconds.
CAUTION
Push Utility Head and Squeegee into steamer until
secure. It will not lock into place but should sit firmly
against steamer.
To remove, pull Squeegee
down on tab.
P
TI
Using your machine
Taking care of your machine
IMPORTANT: Taps should be turned off when steaming around them. Don’t steam clean ovens, oven surfaces or grills when
hot, allow to cool to room temperature first.
IMPORTANT: Don’t use bleach or fabric softener when washing the Microfibre Pad. Always allow the steamer
to fully cool down before removing the Microfibre Pad.
IMPORTANT: Never remove the water tank cap with the product upright as water could leak out–always remove the floorhead
and handle and place on a flat surface before removing the water tank cap.
Using the accessories
Concentration Nozzle
Small brush
Grout Brush
Use to remove soap scum in baths and
shower enclosures and to clean heavily
soiled areas in kitchens.
Ideal for any surface from tiles, sinks,
toilets and oven tops.
Lifts embedded dirt from inbetween tiles.
Utility Head and pad
Squeegee
Emptying the water tank
Unplug, remove floorhead and handle place
steamer on flat surface. Twist water tank
cap anticlockwise and lift to remove.
Empty any excess water
over an empty sink.
Cleaning the Microfibre/Utility Head Pad
40˚C
MAX
Attach utility pad to Utility Head
for use on upholstery and clothes.
Do not use detergent on fabrics
and upholstery.
24hr
Great for leaving your windows, tiles
and mirrors gleaming.
The Microfibre/Utility Head Pad are machine
washable (Max 40⁰C) allow to fully dry
before use. Utility Head Pad is hand wash only.
Test for colour fastness in
a small hidden area of
upholstery/fabric to check
for colour removal
before use.
Ensure steamer
is unpluged before
emptying water tank.
CAUTION
CAUTION
Let’s talk technical
Accessories
Don’t forget your accessories!
IMPORTANT: Turn dial on steamer to ‘OFF’ position, switch off at mains and unplug safely.
Allow to fully cool down before performing maintenance or troubleshooting checks.
Order at: www.vax.co.uk/spares-and-solutions
Clearing blockages
2x Microfibre Pads (Type 1)
1-1-131448-00
Microfibre Pads, ideal to remove dirt and grime. These
cleaning pads attach to the base of the steamer so it’s
quick and easy to fit and remove.
Pro Cleaning Pads (Type 6)
1-1-132319-00
Push the accessory floorhead
release button and lift the main
body from the floorhead to remove.
Also remove the handle.
Use a small thin object such as a
paperclip to insert into the nozzle and
clear any blockage.
To clear a blockage in the floorhead,
remove the Microfibre Pad from the
floorhead, insert a small thin object,
such as a paperclip, into the steam
holes to remove any blockage.
3x pro cleaning pads. Ideal for stubborn stain
removal throughout your home. These cleaning
pads attach to the base of the steamer
so it’s quick and easy to fit and remove.
Steam Mop Cleaning Pads
1-1-131864-00
2x Microfibre Pads, ideal to
remove dirt and grime.
2x coral cleaning pads for your steamer.
Super absorbent and ideal for removing stubborn stains.
Total Home
1-1-132528-00
8x Microfibre Pads. Avoid cross contamination between
different areas of your home with this Total Home Cleaning
Kit. Kit contains 8 x coloured Microfibre Pads for all areas of
your home. Kit also contains a free wash bag worth £9.99.
3x Microfibre Pads (Type 2)
1-1-133071-00
3 washable Microfibre Pads for everyday hard floor
cleaning. Drawstring attachment ideal for everyday
cleaning. Washing machine washable for continuous
use.
Coral Cleaning Pad Kit (Type 3)
1-1-131643-00
2 coral cleaning pads – super absorbent washable
pads, ideal for subborn stains and cleaning uneven
surfaced such as slate.
What to do if it goes wrong
Getting in touch
CAUTION: Always unplug the steamer before performing maintenance/troubleshooting checks.
Problem
Solution
• Check the ‘This pack contains’ panel on the box to make sure the part
is included with your steamer.
Is there an
accessory missing?
†
• Check the on/off control dial position.
The steamer has
no power.
• Check the amber light is illuminated.
• The plug may not be fully pushed into the electrical socket.
• Check the fuse in the plug if this needs replacing, always replace with
a British 13amp fuse.
• There may be no water in water tank, check the water tank has water.
Why is the steamer
not producing steam?
• Check the water tank cap is securely fitted onto the water tank.
• The water may not yet be at temperature . The steamer will take approximately
30 seconds to heat up.
• Steam path may be blocked. Go to ‘Let’s talk technical’.
• Check steam control dial has been turned to ‘on’.
• Water tank level may be low, refill with water.
• If using as a stick mop - handle may not be fully inserted. Release handle,
press handheld trigger to check steam is working. Re-insert handle until
it clicks into place.
• The Microfibre Pad may already be saturated or dirty. Wash the
Microfibre Pad, go to ‘Taking care of your machine’.
Why won’t the Microfibre
pad pick up dirt?
† Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
Notes
Notes
GET IN TOUCH
0330 026 8455
info@vax.co.uk
vax.co.uk
VaxVacuums
@VaxUK
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
S85-CM and SCSMV1SG are manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage
Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.
© 2016 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge is the property of Techtronic Floor Care
Technology Ltd and is registered in the EU and may be pending or registered in other countries.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising