Installation Instructions Starck 10650181 Starck 10971181 Starck 10750181 Starck 28486181 Rough Required Trim (not included) Starck Thermostatic Module 10750181 Trim for Starck Thermostatic Module 10751XX1 Starck Volume Control 10971181 Trim for Starck Volume Control 10972XX1 Rough Required Trim (not included) Starck Handshower System Rough 10650181 Starck Handshower System 10651XX1 Shower Module Rough 28486181 Shower Module 28491XX1 Rough Trim (not included) Rough for Small Shelf / Extension Pipe 40877180 Shelf 40872XX0 Rough for Large Shelf / Extension Pipe 40878180 Shelf 40873XX0 Technical Information Max. water pressure Recommended water pressure Max. hot water temp Recommended hot water temp Hot and cold connections Max. flow rate 145 psi 15 - 75 psi 176°F* 120°-140°F* ¾" NPT 15 gpm @ 44 psi *Know and follow all applicable local plumbing codes when setting the temperature on the water heater. Installation Suggestions The next pages include some showers using the Starck Shower System. These are not the only systems possible. If you have questions regarding your installation, please call Hansgrohe Technical Service at 800 334 0455. Showerheaven 30x30 10625XX1 ½" NPT 40871XX1 40874XX0 40876180 40872XX0 10973181 28486181 10971181 28491XX1 ½" NPT 10972XX1 10750181 10751XX1 28486181 10650181 28491XX1 10651XX1 ¾"NPT ¾" NPT Showerheaven 30x30 10625XX1 40871XX1 40874XX0 40872XX0 28491XX1 10972XX1 10751XX1 28491XX1 10651XX1 Showerheaven 30 x 30 10625XX1 28491XX1 (4x) ½" NPT 28486181 (4x) 10650181 40878180 ¾" NPT 10971181 10750181 10651XX1 ¾" NPT 40873XX0 ¾" NPT 10972XX1 10751XX1 Showerheaven 30x30 10625XX1 28491XX1 (4x) 10651XX1 40873XX0 10751XX1 10972XX1 see page 26 28491XX1 (6x) 28491XX1 ½" NPT ½" NPT ½" NPT 40872XX0 ½" NPT 28491XX1 ¾" NPT 10651XX1 ¾" NPT 28486181 10751XX1 ½" NPT 40877180 10650181 ½" NPT 10750181 28491XX1 28491XX1 ¾" NPT ¾" NPT 10 28491XX1 (6x) 28491XX1 10651XX1 10751XX1 40872XX0 11 Showerheaven 30 x 30 10625XX1 ½” NPT 40872XX0 10751XX1 10651XX1 10750181 10650181 ¾" NPT 12 ¾" NPT Showerheaven 30 x 30 10625XX1 40872XX0 10751XX1 10651XX1 13 Rainfall 28411XX1 ½" NPT ½" NPT 40872XX0 ½” NPT 10751XX1 10651XX1 10750181 10650181 ¾" NPT 14 ¾" NPT Rainfall 28411XX1 40872XX0 10751XX1 10651XX1 15 Showerheaven 30 x 30 10625XX1 ½" NPT 10650181 10750181 10651XX1 ¾" NPT ¾" NPT 10751XX1 40873XX0 16 Showerheaven 30 x 30 10625XX1 10651XX1 40873XX0 10751XX1 17 28491XX1 (4x) ½" NPT 28491XX1 ½" NPT 28491XX1 28486181 ¾" NPT ½" NPT ¾" NPT 10750181 28486181 10751XX1 ½" NPT 28491XX1 ½" NPT 28491XX1 ¾" NPT ¾" NPT 18 28491XX1 (4x) 28491XX1 10751XX1 19 28491XX1 (4x) 28491XX1 (1x) ½" NPT 28491XX1 ½" NPT 10650181 28486181 ½" NPT 10750181 28491XX1 10651XX1 ½" NPT 10751XX1 28491XX1 ¾" NPT ¾" NPT 20 28491XX1 (5x) 28491XX1 28491XX1 10751XX1 10651XX1 28491XX1 21 28491XX1 (4x) ½" NPT 28491XX1 ½" NPT 28486181 (3x) ½" NPT 27980000 10750181 27458000 ¾" NPT ¾" NPT 10751XX1 22 28491XX1 (4x) 27980000 27458000 28491XX1 10751XX1 23 28491XX1 (4x) ½" NPT 28491XX1 ½" NPT ¾" NPT 28486181 27980000 28491XX1 10750181 27458000 ½" NPT 10751XX1 28491XX1 ¾" NPT ¾" NPT 24 28491XX1 (4x) 27980000 28491XX1 27458000 28491XX1 10751XX1 28491XX1 25 Installation Notes The 10750181 thermostat module includes two plugs. Handshower module 10650181 and volume control 10971181 each include one plug. If ½" NPT pipe is to be connected to the end of a valve, cut the plug as shown to create an adapter. If nothing is connected to the end of a valve, seal it using an uncut plug. 10650181 Starck handshower module 10650181 may be connected directly to the 10750181 thermostat module (1), or connected using ½" NPT pipe (2). 10971181 1. Volume control 10971181 may be connected directly to the 10750181 thermostat module (1), or in a free installation (2). 1. 2. 2. The the ¾" NPT side ports are the outlets. If only one is used, the second must be plugged. 26 28486181 Shower module rough 28486181 may also be connected directly to the thermostat module (1) or connected using ½" NPT pipe. 1. The top and bottom ports act only as a "pass through" for water going from the thermostat module to another valve. The shower module is not supplied from these ports. Multiple shower module roughs may be connected. 2. In this diagram, the four connected 28486181 are supplied from the 10971181 volume control. 40878180 The shower module must be supplied through one of the ¾" NPT side inlets. The unused inlet must be plugged. 40877180 Use the extension pipe when a shelf is to be installed between two connected valves. 27 Installation 1 Multiple valves may be connected. Install the dowel pins on the valve. Lubricate the o-rings using the enclosed grease (1). Push the valve inlet of one valve over the outlet of another (2). 2a 2b The additional valve(s) may be connected to either end of the thermostat module. 2. 1. 2. 1. 28 Use a plier to connect the valves with the dowel pins. 3 Install outlet pipes on the volume control valves. Wrap the threads using Teflon tape. 4 Plug unused outlets using ¾" plugs. NPT ¾" NPT ¾" 29 5 Make sure that the connected valves are level. 6 1. Install the noise reducers on the valves (1). Confirm that the connected valves are level in all planes (2). 30 2. If installing ½" NPT pipe between the thermostat module and another valve or bodysprays, install the adapter (see page 26). Wrap the adapter with Teflon tape. Install it in the end of the thermostat module or valve group. G ¾" NPT ½" Wrap the threads on the pipe with Teflon tape and install it in the adapter. Wrap the threads on the plugs with Teflon tape and install them in the ends of the valve group. 31 Install the valve group in the wall. To insure proper fit of the trim, the outside surface of the finished wall must fall between the "min" and "max" markings on the plaster shields. The thermostat module should be screwed firmly to a header board or other backing. Install the hot and cold supplies on the thermostatic mixer. To insure correct operation of the valve, the hot supply must be connected to the hot inlet, and the cold supply must be connected to the cold inlet. Flush the valves Remove the plug at the front of the thermostatic mixer. If bodyspray rough 28486181 is used, remove the plug from it. Turn the volume controls to the "on" position. Turn on the water and flush the hot and cold supply lines through the thermostatic mixer valve for at least five minutes. The cold supply will flush through the outlet at the front of the thermostatic mixer. The hot supply will flush through the valves. 32 1 2 Install sheet rock or backer board over the valves. Seal the wall around the plaster shields using waterproof sealant. Brush adhesive (not included) over the backer board. Install the sealing gasket(s). Cut the sealing gasket to size. Install the tile or other finished wall material over the sealing gasket. 33 Replacement Parts 10750181 95335001 94142000 10650181 95335001 23 x 2,5 95334000 95334000 94142000 95389000 98183000 95337000 28486181 10971181 95335001 95334000 95334000 96492000 94142000 96492000 98183000 98183000 34 Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when cleaning faucets and showers: • Only use cleaning materials which are explicitly intended for this type of application. • Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable damage. • Never mix one cleaning material with another. • Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads, or micro fiber cloths. Cleaning Instructions for Faucets and Showers Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points: • Clean the faucets and showers as and when required • Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner on the fixture longer than necessary. • Regular cleaning can prevent calcification. • When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can enter openings and gaps and cause damage. • After cleaning, rinse thoroughly with clean water to remove any cleaner residue. Important Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using. Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. 35 Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. This warranty is non-transferable. WHAT IS COVERED BY THE WARRANTY This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund the purchase price in exchange for the return of the product. LENGTH OF WARRANTY Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for as long as you own the product and the home in which the product is originally installed. If you purchased the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. (3) Conditions in the home such as excessive water pressure or corrosion. C. Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for installation or reinstallation of the product (including but not limited to proper packaging and shipping costs), or for installation or reinstallation of the product. D. Accessories, connected materials and products, or related products not manufactured by Hansgrohe. TO OBTAIN WARRANTY PARTS OR INFORMATION Contact your Hansgrohe retailer, or contact Technical Service at: Hansgrohe Inc. 1492 Bluegrass Lakes Parkway Alpharetta GA 30004 Toll-free (800) 334-0455. In requesting warranty service, you will need to provide 1. The sales receipt or other evidence of the date and place of purchase. 2. A description of the problem. 3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492 Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe. When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid. EXCLUSIONS AND LIMITATIONS REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT. HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY). Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from State to State. You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson-Moss Warranty Act. PRODUCT INSTRUCTIONS AND QUESTIONS Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel. 770-360-9880 • Fax 770-360-9887 www.hansgrohe-usa.com US - Installation Instructions • Part No. 90482921 • Revised 07/2009 Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If you have questions at any time about the use, installation, or performance of your Hansgrohe product, or this warranty, please call or write to us or call us toll-free at 800 334 0455.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project