Installation Instructions for 200 Watt 12 Volt DC LED Power Supply

Installation Instructions for 200 Watt 12 Volt DC LED Power Supply
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
© 2012 Edge Lighting. All Rights Reserved.
904-PSB-200W-12VDC-06
PSB-200W-12VDC
Installation Instructions for 200 Watt 12 Volt DC LED Power Supply
SAVE THESE INSTRUCTIONS!
GENERAL INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
- RISK OF FIRE: This product must be installed by a
qualified electrician. Turn the power to the electrical box off
during installation. Read the "Important Safety Instructions "
before installation.
- Do not install this power supply in a wet location.
- This product is not suitable for wet locations. It is approved
for the use at any height above the finished floor.
- Do not install *LED fixture closer than three inches or as
specified in the *LED fixture installation instructions to
curtains or similarly combustible materials. Keep insulation
at least 3" away from the enclosure.
- A typical installation is shown. Specific installation must be
in accordance with the local electrical codes.
- To reduce the risk of the system overheating and possibly
causing a fire, make sure all the connections are tight.
- Turn the electrical power off before modifying the lighting
system in any way.
- TO REDUCE RISK OF FIRE, it is important to wire the
power supply for the system as described in this
installation instruction.
- The system is "ETL" listed for USA and Canada only when
all the products used are supplied by Edge Lighting.
- Load the power supply to MAXIMUM 200 Watts.
- Use CDP color dial or CTP color touch screen controller with
RGB LED soft strip.
* See LED fixture installation instructions for proper
placement.
WARNING: This power supply is equipped with a cooling fan. Do not run the power supply in a dusty environment.
All drywall finish and sanding must be done prior to using the power supply. Dust particles may stop the fan from
working & eventually destroy the power supply.
100W, 12VAC LOW VOLTAGE WIRE SIZE CHART
WIRE LENGTH
IN FT
3%
VOLTAGE
DROP
UP TO 8FT
9FT-12FT
13FT-20FT
21FT-31FT
32FT-49FT
WIRE SIZE
14 AWG
12 AWG
10 AWG
8 AWG
6 AWG
VOLTAGE AT END
OF THE WIRE
11.64 VAC
11.65 VAC
11.65 VAC
11.64 VAC
11.64 VAC
60W, 12VAC LOW VOLTAGE WIRE SIZE CHART
3%
VOLTAGE
DROP
WIRE LENGTH
IN FT
UP TO 13FT 14FT-20FT
21FT-34FT
35FT-52FT
WIRE SIZE
14 AWG
12 AWG
10 AWG
8 AWG
VOLTAGE AT END
OF THE WIRE
11.65 VAC
11.65 VAC
11.64 VAC
11.64 VAC
1
Using LED Power Supply with a Light Switch & Warm White
Soft Strip (Non-Dimmable)
A
1: Loosen the four Phillips screws on the front of the power
supply cover to slide the cover off of the case.
PHILLIPS SCREW
COVER
CASE
B
1
2
LIGHT SWITCH
ELECTRICAL BOX
2: Install conduits from the light switch, main panel (line
voltage) and soft strip to the power supply case.
3
3: Run proper size wires from the light switch electrical box to
the power supply case.
4
4: Run the line voltage power wires from the panel to the
power supply case.
C
5: Connect the hot power wire to one of the wires coming from
the switch with a wire nut.
6: Run the other switch wire to the power supply "L" terminal.
3
5
7: Run the neutral power wire to the power supply "N"
terminal.
4
8: Make sure the power supply terminal is grounded in
accordance with local electrical codes.
POWER SUPPLY
8
7
6
2
D
NOTE: This power supply is for multiple runs. Do not
exceed the maximum wattage of the power supply.
NOTE: Use only 12 volt RGB LED soft strip with this
power supply.
9: Connect the LED soft strip red wire into the power supply
"+V" terminal.
10: Connect the LED soft strip black wire into the power supply
"-V" terminal.
Installing LED Power Supply
with RGB Soft Strip & CDP or
CTP Controller
POWER
SUPPLY
10
E
9
PHILLIPS SCREW
POWER
SUPPLY
COVER
CASE
NOTE: Use a DVR-RGB-200 (Sold Separately) with this
power supply. The power supply and the DVR-RGB-200
are installed on the back of the power supply cover.
1: Loosen the four Phillips screws on the front of the power
supply cover to slide the cover off of the case.
2: Carefully pull off the cover from the DVR-RGB-200 driver.
F
CONTROLLER
CONTROLLER POWER SUPPLY
CONDUIT
3
DMX CABLE
DMX CABLE
(BELDEN #9841)
9
M
2
NOTE: Use a deep double gang boxes to fit the controller
and controller power supply (OT-20-120-240-245
recommended).
3: Connect one end of a red wire to "VDC+" of the controller
terminal and the other end of the red wire to the "+24VDC"
of the power supply terminal.
6
ELECTRICAL BOX
DVR
DRIVER
COVER
NOTE: Refer to the "Configuring DimWheel" & "Operating
DimWheel" on page 6 & 7 to properly operate the controller.
7
4
1
CASE
4: Connect one end of a black wire to "Ground" of the controller
terminal and the other end to the "-24VDC" of the power
supply terminal.
5: Run the black and white line voltage wires coming from
the controller power supply to the power supply case.
6: Connect the white wire to "N" terminal of the controller
power supply.
8
7: Connect the black wire to "L" terminal of the controller
power supply.
8: Install conduits from controller, main panel (line voltage),
and soft strip to power supply.
9: Run proper DMX cable (Belden #9841 recommended)
with three data wires from controller to the power supply
box.
3
G
CASE
POWER SUPPLY
DMX CABLE
DVR-RBG-200
M
COVER
10
10: Install a red wire from the power supply "+V" terminal to
DVR-RGB-200 "VDC+" red terminal and a black wire from
power supply "-V" terminal to DVR-RGB-200 "VDC-" blue
terminal.
11: Connect one end of a data wire (blue with white stripes
wire) to controller "LEDSYNC OUT-" terminal. Connect the
other end into the DVR-RGB-200 "DMX in –" terminal.
12: Connect one end of a data wire (white with blue stripes
wire) to controller "LEDSYNC OUT+" terminal. Connect the
other end into the DVR-RGB-200 "DMX in +" terminal.
13: Connect one end of a data wire (bare shield wire) to
controller "LEDSYNC SHIELD" terminal. Connect the other
end into the DVR-RGB-200 "DMX in shield" terminal.
11
NOTE: "DMX in+", "DMX in-", "EXT in+" & "EXT in-",
controller terminals are not used on controller.
12
N
L
13
CONTROLLER
VDC-
EXT in-
VDC+
LEDSync
outLEDSync
out shield
DMX in
shield
LEDSync
out +
DMX in -
DMX in +
-V
+V
10
EXT in+
H
DO NOT
USE
14
CONTROLLER LINE VOLTAGE
POWER SUPPLY WIRES
12
14: Run the line voltage power wires into the power supply.
15: Connect the black power wire and the black controller
wire to the "L" terminal of the power supply.
M
DVR-RGB-200
16: Connect the white power wire and the white controller
wire to the "N" terminal of the power supply.
17: Make sure the power supply ground terminal is grounded
in accordance with local electrical codes.
18: Connect three black wires to the DVR-RGB-200 "GROUP 1
GND", GROUP 2 GND", and "GROUP 3 GND" black terminal
to the power supply "-V" terminal.
POWER
SUPPLY
COVER
16
DVR-RGB-200
15
4
I
NOTE: The DVR-RGB-200 terminals adapt maximum 18
AWG size. To avoid voltage drop, use 6" of 18 AWG size in
RGB terminals connected inline to proper size gauge wire
attached to the RGB LED wires with wire nuts. See the
"Low Voltage Wire Size Chart" on page 1.
19
POWER SUPPLY
19: Use the "Low Voltage Wire Size Chart" on page 1 to
determine proper wire size connecting to the DVR-RGB-200
terminals.
20: Run the proper size green, red, blue, and black wires from
the RGB LED soft strip to the power supply case.
NOTE: This power supply is for multiple runs. Do not
exceed the maximum wattage of the power supply.
NOTE: Use only 12 volt RGB LED soft strip with this
power supply.
21
22
23
21: Connect the black wire into power supply "+V" terminal.
Connect the other end to RGB soft strip black wire(s).
20
DVR-RGB-200
22: Connect the red wire into DVR "Group 1-" red terminal.
Connect the other end to RGB soft strip red wire(s).
23: Connect the green wire into DVR "Group 2-" green
terminal. Connect the other end to RGB soft strip green
wire(s).
24: Connect the blue wire into DVR "Group 3-" blue terminal.
Connect the other end to RGB soft strip red wire(s).
25: Replace the DVR-RGB-200 cover.
J
L N G
D0im-1m0iVng
LED +
LED -
L N G
D0im-1m0iVng
LED +
LED -
26
26: Replace the power supply cover and secure it by tightening
the four Phillips screws.
5
CONTROLLER
27: Align the face plate to the controller and secure using the
two flat head screws.
FACE PLATE
1.5MM ALLEN
WRENCH
PUSH
BUTTON
4
3
N
O
2
1
28: Attach the push button onto the controller center rod and
secure by tightening the M3 set screw with the 1.5mm Allen
wrench provided.
28
27
FLAT HEAD
SCREW
Using LED Power Supply with WW Soft Strip & Standard Switch
CONTROLLER
POWER SUPPLY
POWER SUPPLY
+V
-V
N L
SWITCH
HOT
INPUT POWER
WW SOFT STRIP
NEUTRAL
Using LED Power Supply with RGB Soft Strip & CDP or CTP Controll
CONTROLLER
DO NOT
USE
CONTROLLER
POWER SUPPLY
VDC-
VDC+
N L
LEDSync
outLEDSync
out shield
EXT in-
EXT in+
24VDC
DMX in
shield
5
DMX in -
6
LEDSync
out+
7
DMX in +
K
+-
LINE
POWER SUPPLY
+V
-V
N L
INPUT POWER
HOT
DO NOT
USE
NEUTRAL
DMX CABLE
(BELDEN #9841)
VDC+
VDC-
Group 1
Ext inExt in +
DALI in +
DALI in DALI out+
DALI outDMX in +
DMX in DMX in shield
LedSync out +
LedSync out LedSync shield
M
Group 1 GND
Group 2
Group 2 GND
Group 3
Group 3 GND
Group 4
Group 4 GND
DVR-RGB-200
RGB-LED
SOFT STRIP
6
Selecting Modes
Configure your CDP by setting the DIP switches on the front:
O
N
1
2
O
N
1
2
NOTE: The DIP switches must
remain accessible after installation.
When making changes in the DIP
switch settings, disconnect and
reconnect the power supply to
activate new settings.
COLOR MODE
3
4
5
6
7
3
4
5
6
7
CHASE MODE
Operating CDP
1- Turn the light on
2- Change brightness
3- Turn the light off
TAP
TAP
BRIGHTNESS
Advanced Operation for Color Mode
1- Turn the light on
2- Activate configuration mode
TAP
3- Set Color
4- Save color saving
2 SEC
TAP
Advanced Operation for Chase Mode
1- Turn the light on
2- Activate configuration mode
TAP
2 SEC
3- Set show speed
4- Save color setting
TAP
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising