1. Q6 Features
• Supports 135 hours continuous voice recording.
• Auto voice activate function support starting recording when in-car conversation starts and stops when the conversation
• Built-in 2000mAh rechargeable high temperature resistance lithium battery enables device working inside the car around
high temperature environment.
• Industrial-strength magnets built-in supports device being attached under the car seat to avoid regular car cleaning.
Hardware Specifications:
Size: 90mm x35mm x 20mm Weight: 86g
Storage Temp: -20 to 85°C
Operating Temp: -10 to 55°C
Power: Rechargeable, 2000mAh, Lithium-polymer Battery
2. Product Image
(see picture)
LED Indicator
LED Flashlight
3. Button Operation
Charging/Data Slot
3.1 Power on/off
a. On: Short press button 2 times, and then long press 1 time until blue indicating light on for 3 seconds.
b. Off: Short press button 4 times, and then long press 1 time until blue indicating light flashes for 3 times.
3.2 Status Check
a. On: Long press button. blue indicating light turns on for 3 second refers to device is on.
b. Off: Long press button. blue indicating light flashes for 3 time refers to device is off.
3.3 Power Check and Recharge
a. Power Status: Short press button 1 times, and then long press 1 time until blue indicating light flashes 1-4 times. (1=low
power, 4=high power)
b. Device will be turned off when out of power, need to be turned on again after charging.
c. Red Indicating light will be on during charging and will turns off when full charged.
3.4 Flashlight Function
On/Off : Short press button 2 time.
4. Recording Settings
All recoding settings including time, voice sensitivities, mute time, voice quality, record amplify and record time periods can
revised by editing a record setting file.
4.1 RECORD setting file
Connect device with PC via USB cable. There will be RECORD.txt in the folder.
4.2 Settings
a. Time Settings
Time format: Year-Month-Day Hour-Minute-Second
Change the time to the current time after the equal sign.
b. Voice Sensitivity Settings
The bigger number of the sensitivity rate the higher voice required.
Voice Sensitivity Range: 0-50
Default Rate: 10
c. Mute Time Settings
Device will stop recording after conversation ended for certain minutes.
Mute rate: 0-999 minutes
Default Rate: 3
d. Voice Quality Settings
Rate 1: 32Kbps, 8G memory can store 580 hours audio
Rate 2: 64Kbps, 8G memory can store 290 hours audio
Rate 3: 192kbps, 8G memory can store 96 hours audio
Default Rate: 2
e. Record Amplify Settings
For long distance recording, voice will be enhanced by amplifying record.
Rate 1: Within 1M range
Rate 2: Within 1-3M range
Rate 3: Within 3-5M range
Rate 4: Over 5M range
f. Record time periods settings
The time setting default one week for one cycle. From Sunday to Saturday, you can set the record time periods according to
your request.
The default time period as below:
Note: the device is on during above time periods. Outside these time periods, the device is off.
If no need record for the whole day, please set it blank after the equal sign.
If need record for the whole day, set it as 00:00-23:59 after the equal sign.
One day can set two time periods maximum. For example: Sun.= 08:00-12:00, 14:00-18:00
4.3 Update Settings
Very important notice: Set Update Setting to Y, system will start update settings after U disk is exited.
System will not start update settings if it is set to N.
5. Hardware Specification
Input DC: USB 5.0V 1000mA
Battery Complicity: 3.7V/2000mAh
Charging Time: around 3 hours
Recording Power: Continuous 135 recording for 1 charge
Recording file format: WAV format
Memory : Nand flash 8GB
Recording Sampling Rate:48KHz/16bit
Voice Quality: 192Kbps/64Kbps/32Kbps
Support Recording Time32Kbps/8G/580 hours;64Kbps/8G/290 hours;192Kbps/8G/96 hours
Recoding Distance: Built-in Automatic Gain Control,support up to 10M recording distance.
Frequency: 20Hz-20KHz
Connector: Standard Micro USB Slot
Flash Light: LED 0.1W
Support System: Windows XP/VISTA/WIN 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF