now - Robe Lighting
Version 1.1
Robin 800 LEDWash Wireless DMX
Day Light
Table of contents
1. Safety instructions.......................................................................................................... 3
2. Fixture exterior view ...................................................................................................... 5
3. Installation....................................................................................................................... 6
3.1 Connection to the mains............................................................................................. 6
3.2 Installing the top hat.................................................................................................... 7
3.3 Installing the front clear transparent cover.................................................................. 7
3.4 Rigging the fixture....................................................................................................... 9
3.5 DMX-512 connection................................................................................................. 11
3.6 Ethernet connection.................................................................................................. 12
4. Wireless DMX operation............................................................................................... 14
5. Control menu map......................................................................................................... 15
6. Robin 800 LEDWash Day Light - DMX chart............................................................... 18
6.1 LED zone order......................................................................................................... 20
7. Control menu ................................................................................................................ 21
7.1 Tab " Address".......................................................................................................... 22
7.2 Tab "Information"...................................................................................................... 23
7.3 Tab "Personality"....................................................................................................... 24
7.4 Tab "Manual Control"................................................................................................ 26
7.5 Tab "Stand-alone" .................................................................................................... 26
7.6 Tab "Service"............................................................................................................ 27
8. RDM................................................................................................................................ 28
9. Error and information messages................................................................................. 29
10. Technical Specifications............................................................................................ 30
11. Maintenance and cleaning.......................................................................................... 32
11.1 Replacing fuse........................................................................................................ 32
12. Changelog.................................................................................................................... 33
13. Photometric diagrams................................................................................................ 34
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR ROBIN 800 LEDWASH !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
The Robin 800 LEDWash was designed for indoor use and it is intended for
professional application only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS
UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the fixture.
This fixture should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the fixture from AC power before cleaning, removing or installing the fuses, or any part.
The power plug has to be accessible after installing the fixture. Do not overload wall outlets and extension cords
as this canresult in fire or electric shock.
Do not allow anything to rest on the power cord. Do not locate this fixture where the cord may be damaged by
persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the fixture and the power
cord from time to time.
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore this fixture has to be connected to
a mains socket outlet with a protective earthing connection.
Do not connect this fixture to a dimmer pack.
LED light emission. Risk of eye injury. Do not look into the beam at a distance of less
than 1 meter from the front surface of the product. Do not view the light output with
optical instruments or any device that may conncentrate the beam
If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Do not shake the fixture. Avoid brute force when installing or operating the fixture.
This fixture was designed for indoor use only, do not expose this unit to rain or use near water.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat, moisture
or dust.
Air vents and slots in the fixture´s head and base are provided for ventilation, to ensure reliable operation of
the device and to protect it from overheating.
Do not block the LEDs array with any object when the fixture is under operation.
The openings should never be covered with cloth or other materials, and never must be blocked.
This fixture should not be placed in a built-in installation unless proper ventilation is provided.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
Always use a secondary safety cable when mounting this fixture.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
Do not block the front objective LEDs with any object when the fixture is under operation.
The fixture becomes very hot during operation. Allow the fixture to cool approximately 20 minutes prior to
manipulate with it.
Operate the fixture only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the fixture. Most damages are the result of unprofessional operation!
Please use the original packaging if the fixture is to be transported.
Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, crash etc.
2. Fixture exterior view
1 - Lens array
2 - Carrying handle
3 - QVGA touch screen
4 - Control buttons
5 - Base
6 - Head cover
7 - Fan
8 - Yoke
9 - Ethernet input
10 - 3-pin DMX OUT
11 - 3-pin DMX IN
12 - 5-pin DMX OUT
13 - 5-pin DMX IN
14 - Power con
15 - Fuse holder
The ENTER/DISPLAY ON button also serves for switching the display on when the fixture is disconnected
from the mains.
3. Installation
Fixtures must be installed by a Qualified electrician in accordance with all
national and local electrical and construction codes and regulation.
3.1 Connection to the mains
For protection from electric shock, the fixture must be earthed!
The Robin 800 LEDWash is equipped with auto-switching power supply that automatically adjusts to any 50/60Hz
AC power source from 100-240 Volts.
Install a suitable plug on the power cord, note that the cores in the power cord are coloured according to the
following table. The earth has to be connected!
If you have any doubts about proper installation, consult a qualified electrician.
Core (EU)
Core (US)
Connection
Brown
Black
Live L
Light blue
White
Neutral
N
Yellow/Green
Green
Earth
Plug Terminal Marking
3.2 Installing the top hat
Disconnect
the fixture from mains before top hat installation
1. Go to the fixture menu and set reduced tilt movement (Personality --> Pan/Tilt Setting-->
Tilt Movement Range --> reduced).
2.Place the top hat on the head, press locks (1) and turn the top hat counter-clockwise until it snap into slots
in the flange.
3.3 Installing the front clear transparent cover
Uninstallation of the beam shaper
1. Disconnect fixture from the mains.
2. Press and hold both locks (1) and turn the beam shaper module (2) clockwise until three pins (3)
are loosen from slots (4).
3. Remove the beam shaper module (2) from the fixture head.
4. Connect fixture to the mains.
Installation of the front clear transparent cover
5. Place the front transparent cover (5) on the head in this way that adjusting pegs (6) will point to
slots in the head (7).
6. Turn the front transparent cover (5) anticlockwise until three pins (3) snap into slots (4).
7. Connect fixture to the mains.
3.4 Rigging the fixture
The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1
hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down if
the main attachment fails.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert
before taking into operation for the first time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
The fixture should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead
use a professional structural rigger. Improper installation can result in bodily injury or damage to property.
The fixture has to be installed out of the reach of people.
If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The
fixture must never be fixed swinging freely in the room.
Caution: Fixture may cause severe injuries when crashing down! If you have doubts concerning the safety of
a possible installation, do not install the moving head!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the fixture’s
weight.
.
.
When installing the device, make sure there is no highly inflammable
material (decoration articles, etc.) in a distance of min. 0.5 m.
CAUTION!
Use an appropriate clamp to rig the fixture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that the
structure (truss) to which you are attaching the fixtures is secure.
The fixture can be placed directly on the stage floor or rigged on a truss without altering its operation characte­
ristics .
For securing a fixture to the truss install a safety wire that can hold at least 10 times the weight of the fixture.
Use only safety wire with screw-on carabine. Pull the safety wire through the carrying handles and around the
truss as shown on the pictures below.
Note: If the safety wire is too long, whip it several times around the trusss in order to attach the fixture tight.
In case of an accident, the way of the falling fixture will be short.
Rigging via two Omega holders
Securing the fixture via one safety wire
Securing the fixture via two safety wires
1-Fixture
2-Omega holder
3-Clamp
4-Trust
5-Safety chain
The fixture can be also rigged by means of the mounting adapter (option) for one Omega holder:.
In this case the fixture can hang on the truss in horizontal position only, not sideways .
10
3.5 DMX-512 connection
The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired
in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the fixture or one fixture with another.
DMX - output
XLR mounting-sockets (rear view):
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
DMX-input
XLR mounting-plugs (rear view):
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with
the DMX input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
11
3.6 Ethernet connection
The fixtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control software running on your PC (or light console) has to support Art-Net protocol.
Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow
transfer of large amounts of DMX 512 data over a wide area using standard network technology.
IP address is the Internet protocol address.The IP uniquely identifies any node (fixture) on a network.
The Universe is a single DMX 512 frame of 512 channels.
The Robin 300E Wash is equipped with 8-pin RJ- 45 socket for Ethernet input.Use a network cable category 5
(with four “twisted” wire pairs) and standard RJ-45 plugs in order to connect the fixture to the network.
RJ-45 socket (front view):
RJ-45 plug (front view):
1- TD+ 5- Not connected
2- TD-
6- RX
3- RX+
7- Not connected
4- Not connected8- Not connected
Patch cables that connect fixtures to the hubs or LAN sockets are wired 1:1,that is,pins with the same numbers
are connected together:
1-12-2
3-3
4-4
5-5
6-6
7-78-8
If only the fixture and the computer are to be interconnected,no hubs or other active components are needed.
A cross-cable has to be used:
1-32-6
3-1
4-8
5-7
6-2
7-58-4
If the fixture is connected with active Ethernet socket (e.g. switch) the network icon
will appear at the
bottom right corner of the screen:
Direct Ethernet operation
Connect the Ethernet inputs of all fixtures with the Ethernet network.
Option “ Artnet (gMaI or gMA2)" has to be selected from “Ethernet Mode” menu on the fixture.
Set IP address (002.xxx.xxx.xxx / 010.xxx.xxx.xxx) and the Universe.
(DMX address=46)
IP addres=002.168.002.004
Universe=1
(DMX address=23)
IP addres=002.168.002.003
Universe=1
(DMX address=1)
IP addres=002.168.002.002
Universe=1
An advised PC setting: IP address: 002.xxx.xxx.xxx / 010.xxx.xxx.xxx (Different from fixture IP addresses)
NET mask: 255.0.0.0
12
Ethernet / DMX operation
Options “Art2DMX” has to be selected from the “Ethernet Mode” menu on the first fixture (connected to the
Ethernet) in the fixture chain,next fixtures have standard DMX setting.
Connect the Ethernet-input of the first fixture in the data chain with the network. Connect the DMX output of
this fixture with the input of the next fixture until all fixtures are connected to the DMX chain.
Caution: At the last fixture, the DMX chain has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the last fixture.
Example:
DMX address=1
IP addres=002.168.002.002
Universe=0
DMX address=23
DMX address=1
IP addres=002.168.002.003
Universe=1
DMX address=23
13
DMX address=46
DMX address=46
4. Wireless DMX operation
The Robin 800 LEDWash is equipped with the Lumen Radio CRMX module and antenna for receiving DMX
signal. CRMX module operates on the 2.4 GHz band.
The item " Wireless " from the menu "DMX Input" allows you to activate receiving of wireless DMX (Personality--> DMX Input -->Wireless.). First two options from the "DMX Input" menu are stated in DMX chart as well
(channel Power/Special functions , range of 10-19 DMX). If DMX input option is changed by DMX command,
the change is permanently written into fixture´s memory.
DMX range of 10-19 switching fixture to the wired/wireless operation is active only during first 10 seconds after switching the fixture on.
After switching the fixture on, the fixture checks both modes of receiving DMX in the following order:
1. For the first five seconds, the fixture receives DMX signal from the wired input. If the Power/Special functions
channel is set at some DMX input option, the fixture will receive DMX value according to this option. If DMX input
option is set to the wired input , this option is saved and checking procedure is finished. If DMX input option is
not set, the fixture continues next 5 seconds in scanning wireless DMX signal-see point 2.
2. For the next 5 seconds the fixture receives wireless DMX signal and again detects if the Power/Special functions channel is set at some DMX input option, if not, the fixture will take option which is set in the fixture menu
"DMX Input".
To link the fixture with DMX transmitter.
The fixture can be only linked with the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Wireless State“ (Information
-->Wireless State).
To unlink the fixture from DMX transmitter.
The fixture can be unlinked from receiver via the menu item “ Unlink Wireless Adapter“ (Information--> Wireless
State --> Unlink Wireless Adapter.).
Note: If the option "Wireless In/XLR Out" is selected (Personality--> DMX Input -->Wireless In/XLR Out), the
fixture receives wireless DMX and sends the signal to its wired DMX output. The fixture behaves as " Wireless/Wired" adapter.
Example of using
14
5. Control menu map
Default settings=Bold print
Tab
Level 1
Level 2
Level 3
Addressing
Settings
DMX Address
001-255
Ethernet Settings
Ethernet Mode
Level 4
Level 5
Disable
ArtNet
gMAI
gMA2
Art2DMX
IP Address/NetMask
Default IP Address
Custom IP Address
Net Mask
Information
Fixture Times
Power On Time
Fixture Temperatures
LEDs Temperature
ArtNet Universe
0-255
MANet settings
MANet I/IIUniverse
1-256
MANet Session ID
1-32
Total Hours
Resetable Hours
Current
Maximum NonRes.
Maximum Res.
AmbientTemperature
Current
Maximum NonRes.
Maximum Res.
Base Temperature
Current
Maximum NonRes.
Maximum Res.
DMX Values
Pan
:
Dimmer Fine
Wireless State
Signal Quality
Unlink Wireless Adapter
Software Versions
Display System
Module M
Module L
Product IDs
Mac Address
RDM UID
RDM Label
View Logs
Fixture Errors
Fixture Status
Power On
Power Off
Fixture Position
Fixture Temperatures
LEDs Temperature
Ambient Temperature
Base Temperature
Personality
User Mode
User A Settings
User B Settings
User C Settings
DMX Presets
Mode 1
:
Mode 6
View Selected Preset
DMX Input
Wired
15
Level 6
Tab
Level 1
Level 2
Level 3
Level 4
Wireless
Wireless In/XLR Out
Pan/Tilt Settings
Pan Reverse
Off, On
Tilt Reverse
Off, On
Pan/Tilt Feedback
Off, On
Pan/Tilt mode
Time
Speed
Tilt Movemement range
Stand.
Reduc.
Microphone Sensitivity
1-10-20
Blackout Settings
Blackout During M.C.
Off, On
Blackout while:
Pan/Tilt moving
Zoom Mode
Off, On
Beam Zoom
Wash Zoom
Init Effect Positions
Screen Settings
Pan
0-255
Dimmer Fine
0-255
Display Intensity
1-10
Screen Saver Delay
Off-10min.
Touchscreen Lock
Off-10min.
Recalibrate Touchscreen
Display Orientation
Normal
Inverted
Auto
Temperature Unit
°C,°F
Fan Mode
Auto
High
Theatre mode
On, Off
Date & Time Settings
Default Settings
Manual Control
Reset Functions
Total System Reset
Pan/Tilt reset
Zoom Reset.
Preset Effect Control
Pan
Position 1-Position 5
:
Manual Effect Control
Dimmer
Position 1- Position 5
Pan
0-255
:
Dimmer Fine
Stand -Alone
Test Sequences
0-255
Dynamic Mode
Static Mode
MusicTrigger
Off, On
Preset Playback
None
Pan
0-255
Tilt
0-255
Zoom
0-255
Test
:
Prog. 3
Play Program
Play Program 1
Play Program 2
16
Level 5
Level 6
Tab
Level 1
Level 2
Level 3
Level 4
Level 5
Start Step
1-100
End Step
1-100
Edit Program Steps
Step 1
Pan (0-255)
:
:
:
Dimmer Fine
(0-255)
:
Step Time
(0-25.5s)
Step 100
Pan (0-255)
Play Program 3
Edit Program
Edit Program 1
:
Dimmer Fine
(0-255)
Fade Time
(0-25.5s)
Service
Adjust DMX Values
Pan
0-255
:
Calibrations
Dimmer Fine
0-255
Calibrate Effects
Pan
0-255
Tilt
0-255
Load Default Calibrations
Update Software
17
Level 6
Robin 800 LEDWash Day Light - DMX chart
Version 1.0
Mode/Channel
Value
Function
Type of
control
1
2
3
4
5
6
1
1
1
1
1
1
0-255
Pan (8 bit)
Pan movement by 450°
proportional
2
2
2
2
2
2
0-255
Pan Fine (16 bit)
Fine control of pan movement
proportional
3
3
3
3
3
3
0-255
Tilt (8bit)
Tilt movement by 300°
proportional
4
4
4
4
4
4
0-255
Tilt fine (16 bit)
Fine control of tilt movement
proportional
0
5
5
5
5
5
5
6
6
6
6
step
Speed from max. to min. (vector mode)
proportional
1 - 255
Time from 0.1 s to 25.5 s.
proportional
10 - 14
15 - 19
6
P./T. speed-set Speed Mode in menu: P./T. Mode
1 - 255
0-9
6
Pan/Tilt speed, Pan/Tilt time
Max. speed (tracking mode)
20 - 49
50-59
60-69
70 - 79
80 - 89
90 - 99
100-109
110-114
115-119
120-139
140 - 149
150 - 179
180 - 189
190 - 199
200 - 209
210 - 239
240
P./T. time - set Time Mode in menu: Pan/Tilt Mode
Special functions
Reserved
To activate following functions , stop in DMX value
for at least 3sec. and shutter must be closed at least
3sec. (Shutter channel 17/13/10/10/16 must be at
range of 0-31DMX). Corresponding menu items are
temporily overrided except DMX Input.
DMX input: Wired DMX *
DMX input: Wireless DMX*
* function is active only10 seconds after switching the fixture on
Reserved
Pan/Tilt speed mode
Pan/Tilt time mode
Blackout while pan/tilt moving
Disabled blackout while pan/tilt moving
Theatre mode On
Theatre mode Off
Zoom mode: Wash
Zoom mode:Beam
Reserved
To activate following reset function, stop in DMX
value for at least 3 sec.
Pan/Tilt reset
Reserved
Zoom/beam shaper reset
Reserved
Total reset
Reserved
Disable "Silent mode" of fans
To activate "Silent ", stop in range of 241-255 at least 3 sec.
241 - 255 "Silent mode of fans":fans noise from min. to max.
step
step
step
step
step
step
step
step
step
step
step
step
step
step
proportional
7
-
7
-
14
7
0-255
White (8 bit) - LED zone 1
Dimmer intensity from 0% to 100%
proportional
8
-
-
-
15
8
0-255
White fine (16 bit) - LED zone 1
Fine dimming
proportional
9
-
8
-
16
9
0-255
White (8 bit) - LED zone 2
Dimmer intensity from 0% to 100%
proportional
10
-
-
-
17 10
0-255
White fine (16 bit) - LED zone 2
Fine dimming
proportional
0-255
White (8 bit) - LED zone 3
Dimmer intensity from 0% to 100%
proportional
11
-
9
-
18 11
18
Mode/Channel
1
2
3
4
5
12
-
-
-
19 12
13
7
10
7
6
13 13
14
8
11
8
9
-
15
9
12
9
7
14
16 10
-
-
8
15
Value
Type of
control
0-255
White fine (16 bit) - LED zone 3
Fine dimming
0-7
8-15
LED zone effects
No function
All LEDs ON
step
16-23
24-31
32-39
40-47
48-55
56-63
64-71
72-79
80-87
88-95
96-103
104-111
112-119
120-255
Effect 1
Effect 2
Effect 3
Effect 4
Effect 5
Effect 6
Effect 7
Effect 8
Effect 9
Effect 10
Effect 11
Effect 12
Effect 13
Reserved
step
step
step
step
step
step
step
step
step
step
step
step
step
step
0-127
128-191
192-255
Beam shaper
Beam shaper indexing 0°-180°
Forwards rotation from fast to slow
Backwards rotation from slow to fast
proportional
proportional
proportional
0 - 255
Zoom (8 bit)
Zoom from min. to max. beam angle
proportional
0 - 255
Zoom fine (16 bit)
Fine zooming from min. to max.
proportional
0-31
32-63
64-95
96-111
112-127
17 11 13 10 10 16
Function
128-143
144-159
160-175
176-191
192-223
224-255
Speed of the following effects can be controlled by the
Shutter/Strobe channel (DMX values of 96-127)
Syhutter/Strobe
Shutter closed
Strobe effect from slow--> fast (zone 3 only)
Strobe effect from slow--> fast (All zones together)
--------------Set value on LED zone effects--------------
Zone effects speed control, slow--> fast
Zone effects speed control, fast--> slow /opposite
direction/
---------------------------------------------------------------------------
Opening pulses in sequences from slow--> fast
(All zones together)
Closing pulses in sequences from fast--> slow
(All zones together)
Random strobe effect from slow--> fast (random zone)
Random strobe effect from slow--> fast (random zone +
random strobe)
Random strobe effect from slow --> fast (All zones
together)
Shutter open
proportional
step
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
step
18 12 14 11 11 17
0-255
Dimmer (8 bit)
Dimmer intensity from 0% to 100%
proportional
19 13
0-255
Dimmer fine (16 bit)
Fine dimming
proportional
-
-
12 18
19
6.1 LED zone order
20
7. Control menu
The Robin 800 LEDWash Light is equipped with the QVGA Robe touch screen with battery backup which
allows to set the fixture´s behaviour according to your needs, obtain information on its operation, test its various parts and lastly program it, if it has to be used in a stand-alone mode.
The fixture´s menu can be controlled either by the control buttons or directly by touching the icon.
Control buttons on the front panel:
[ESCAPE] button used to leave the menu without saving changes.
[NEXT] , [PREV] buttons for moving between menu items and symbols, adjusting values.
[ENTER/Display On] button used to enter the selected menu (menu item) and to confirm adjusted value.
If the fixture is disconnected from mains, the button switches the touch screen on.
Icons used in the touch screen menu:
- [back arrow] used to move back to the previous screen (menu).
- [up arrow] used to move up on the previous page.
- [down arrow] used to move down on the next page.
- [confirm] used to save adjusted values, to leave menu or to perform desired action.
- [cancel] used to leave menu item without saving changes.
- [confirm+copy] used to save adjusted values and copy them to the next prog. step.
- [warning icon] used to indicate some error which has occurred in the fixture.
- [Ethernet] used to indicate Ethernet connected.
- [display turn] used to turn the display by 180°.
The menu page displays icons for each function that you can perform from the touch screen.
After switching the fixture on, the touch screen shows the screen with the ROBE logo:
21
Note: The green icon at the top right corner of the screen indicates the level of the display battery charging. If
the whole icon is green, the battery is fully charged while the red icon indicates exhausted battery. The battery
charges during fixture operation, its charging lasts cca 6 hours.
We recommend that the fixture should be in operation at least 7 hours per week to keep the battery fully charged.
If you switch the fixture on and this screen will not appear till 1 minute, switch the fixture off and on again. If the
screen lights, the battery is exhausted. In case the screen still does not light, the battery is faulty.
This is also indicated by an error message "Faulty battery" and if such an error message appears the battery
should be replaced immediately. The lifetime of the battery is highly dependent on ambient temperature (and
consequently on base temperature). If the maximum ambient temperatures (as recorded and displayed in menu:
Information -> Fixture Temperatures -> Ambient Temperature -> Maximum NonRes.) are kept within the specified limits, the battery should last for at least two years. Shell the ambient temperatures exceed the specified
maximum temperature, the lifetime of the batteries could be considerably shortened even up to just one year
or less and also result in physical damage (battery leakage) or unreliable fixture functions.
Damage caused by batteries failed due to exceeded maximum ambient temperature cannot be claimed under
warranty terms.
Touch any part of the screen or press the [ENTER/Display On] button to display the initial screen with the current stored DMX address:
Touch the green arrow at the bottom right corner of the screen or press the [ENTER/Display On] button to enter
the " Address" menu.
An item (such as a Tab, menu item, text box, icon) may be selected from a screen by simply touching the item
in the list or by pressing the [NEXT] or [PREV] buttons to scroll through list items. With each press, the next
item is highlighted. Press [ENTER/Display On] to select the highlighted item.
Before first fixture operation, set current date and time in the menu "Date &Time
Setings" (menu path: Personality--> Date &Time Setings).
7.1 Tab " Address"
Settings - Select the menu to set desired fixture address setting.
DMX Address - Select the menu to set the DMX start address.
Ethernet Settings - The menu allows all needed settings for the Ethernet operation
Ethernet Mode - Use the menu to set the Ethernet operation mode:
Disable - The option disables Ethernet operation.
Artnet - Fixture receives Artnet protocol - every fixture has to be connected to the network.
gMAI - Fixture receives MANet protocol.
gMA2 - Fixture receives MANet2 protocol.
Art2DMX - Fixture receives Artnet protocol from the Ethernet input and sends DMX
data to its DMX output (fixture works as an "Artnet/DMX converter", next fixture can
be connected to its DMX output and you can build a standard DMX chain by
connecting another fixtures. Only one fixture has to be connected to the Ethernet.
22
IP Address/Net Mask - Select this menu to set IP address. IP address is the Internet protocol
address.The IP uniquely identifies any node (fixture) on a network.
There cannot be 2 fixtures with the same IP address on the network!
Default IP Address -Preset IP address, you can set up only first byte of IP address (2 or
10) e.g. 002.019.052.086.
Custom IP Address - The option enables to set up all bytes of IP address.
Net Mask - The option enables to set up all bytes of Net Mask.
. ArtNet Universe - Use this item to set a Universe (0-255). The Universe is a single DMX
512 frame of 512 channels.
MANet Settings - Use this menu to set parameters for MANet operation.
MANet I/II Universe - The value of this item can be set in range 1-256.
MANet Session ID - The value of this item can be set in range 1-32.
7.2 Tab "Information"
Fixture Times - The menu provides readouts of fixture operation hours.
Power On Time Hours - Select this menu to read the number of fixture operation hours.
Total Hours - The item shows the total number of the operation hours since the Robin 800 LEDWash has been fabricated.
Resetable Hours - The item shows the number of the operation hours that the Robin 800 LEDWash has been powered on since the counter was last reset.
In order to reset this counter to 0, touch the text box next to the item "Resetable Hours:"
Fixture Temperatures - The menu is used to view temperatures of the fixture´s inside.
LEDs Temperature - The menu shows temperatures in the LED module.
Current - A current temperature of the LED module.
Maximum NonRes. - A maximum temperature of the the LED module since the fixture has
been fabricated.
Maximum Res. - A maximum temperature of the the LED module since the counter
was last reset.
I��������������������������������������������������������������������������������������
n order to reset this counter to 0, touch the text box next to the item "Maximum Res."
Ambient Temperature - The menu shows temperature of the induced air on the fan in the fixture base .
Current - A current temperature of the induced air in the fixture base.
Maximum NonRes. - A maximum temperature of the induced air in the fixture base since
the fixture has been fabricated.
Maximum Res. - A maximum temperature of the induced air in the fixture base since
since the counter was last reset.
In order to reset this counter to 0, touch the text box next to the item "Maximum Res."
Base Temperature - The menu shows temperature in the fixture base.
Current - A current temperature in the fixture base.
Maximum NonRes. - A maximum temperature in the fixture base since the fixture has
been fabricated.
Maximum Res. - A maximum temperature in the fixture base since the counter
was last reset.
In order to reset this counter to 0, touch the text box next to the item "Maximum Res."
DMX Values - The menu is used to read DMX values of each channel received by the fixture.
Wireless State - The menu serves for reading of the wireless operation status (only for Wireless DMX version).
Unlink Wireless Adapter - The item serves for unlinking the fixture from the transmitter.
Product IDs - The menu is used to read the MAC Address ,RDM UID and RDM Label.
Software Version - Select this item to read the software version of the fixture modules:
Display System - A display processor on the display board in the fixture base
23
Module M - A pan/Tilt processor on the main board in the fixture arm
Module L - Zoom and LED control processor on the board in the fixture head.
View Logs - Use this menu to read fixture´s data which have been recorded during fixture operation. This
colected data allows easier troubleshooting.
Fixture Errors - Use this menu to read fixture errors which have occured during fixture operation.
Fixture States - Recorded following actions: Fixture On, Fixture Off.
Fixture Position - Recorded installation positions of the fixture:
Fixture Temperatures - Recorded temperatures which have exceeded defined levels.
7.3 Tab "Personality"
User mode - The Robin 800 LEDWash allows you to recall up to 3 user settings. After switching the fixture on
for the first time, the User A settings is active. Now all changes made in the “Personality” menu , ”Addressing”
menu and the “Music Trigger“ and “ Preset Playback“ items from the “Stand-alone” menu are saved to the
User A settings. If you now select the User B settings, from this moment the changes made in these menus will
be saved to the User B settings. After switching the fixture off and on, the User B setting is active. In this way
you may use the 3 fixture operating behaviours.
User A Settings - the function recalls the user A settings.
User B Settings - the function recalls the user B settings.
User C Settings - the function recalls the user C settings.
DMX Preset - Use the menu to select desired DMX mode.
Mode 1 - 19 control channels
Mode 2 - 13 control channels
Mode 3 - 14 control channels
Mode 4 - 11 control channels
Mode 5 - 19 control channels
. Mode 6 - 18 control channels (compatible with LEDWash 600 DL mode1)
View Selected Preset - Use the menu to display channels included in the selected mode.
DMX Input- Use the menu to select mode of receiving DMX signal.
Wired - DMX signal is received by means of the standard DMX cable.
Wireless - DMX signal is received by means of the inbuilt wireless module.
Wireless In/XLR Out- the fixture receives wireless DMX and sends the signal to its wired DMX output.
The fixture behaves as " Wireless/Wired" adapter.
The options "Wired" and "Wireless" are also stated in DMX chart (channel Power/Special functions).
Pan/Tilt Settings - Use the menu set behaviour of both pan and tilt movements.
Pan Reverse - The item allows to invert pan movement.
Tilt Reverse - The item allows to invert tilt movement.
Pan/Tilt Feedback - The item allows to return the mowing head to the required pan/tilt position after
changing the position by an external force if this option is set on.
Note. Be careful, the Pan/Tilt Feedback should be permanent On, the option Off is not suitable for standard
operation and the head of the fixture can be damaged!
Pan/Tilt mode - Use this menu to set the mode of the pan/tilt movement
Time mode – The pan and tilt will move with different speeds and they will come at
24
the same time to the end point of their tracks (pan and tilt use their optimal speeds).
Time of the pan/tilt movement (25.5 sec. max.) is set by the channel "Pan/Tilt speed, Pan/Tilt
time".
Speed Mode - Both Pan and tilt will move with the same speed as adjusted at the channel
"Pan/Tilt speed, Pan/Tilt time".
Tilt Movement Range - Use this menu to set the range of the tilt movement of the fixture´s head
Stand. – Standard range 0-300°.
Reduc. - Reduced range 0-210°. This option must be selected when the top hat is installed
otherwise fixture´s head rans into base.
Microphone Sensitivity - Enter the menu if you want to adjust the microphone sensitivity from 1 (max.) to 20
(min.).
Blackout Settings - Use the menu if you need to close the light output under certain conditions which are
described below
Blackout DMC - Blackout during movement correction. Set this option On if you wish to close light
output during the time when the head goes to its correct position, which has been changed by an
external force.
Active Blackouts - Use this menu if you wish to close the light output during effect changes.
Pan/Tilt Moving - The menu item enables to close light output while the pan/tilt coordinates
are changing.
Zoom mode - Use this menu to change min. beam angle.
Beam Zoom - Beam angle 8°-53° (half beam)
Wash Zoom - Beam angle 15°-53° (half beam), compatible zoom range with the Robin LEDWash 300/600.
These zoom options are also stated in DMX chart (channel Power/Special functions).
Init Effect Positions - Use the menu to set all effects to the desired positions at which they will stay after
switching the fixture on without DMX signal connected.
Screen Settings - Use this menu to change the touch screen settings.
Display Intensity - The item allows to control the intensity of the screen (1-min., 10-max.).
Screen saver Delay - The item allows you to keep the screen on or to turn it off automatically after 1-10
minutes after last touch (or pressing any button on the control panel).
Touchscreen Lock - The item allows you to lock the screen after last touch (or pressing any button on the
control panel). The time delay can be set in range of 1-10 minutes.To unlock the screen, press the
[ENTER/Display On] button.
Recalibrate Touchscreen - The item starts calibration of the touchscreen. Follow the instructions on
the screen.
Display Orientation - The menu allows to change display orientation.
Normal - Standard display orientation if the fixture is placed horizontally (e.g. on the ground).
Inverted - Inverted orientation (needed if the fixture is hanging on the truss).
Auto - The option activates a gravitation sensor for automatic screen orientation.
Note: Auto option is set as default. You change the display orientation by touching the icon
on the display,
an the option set in the "Display Orientation" menu is temporarily overriden.
Temperature unit - Use the menu item to change temperature unit from °C to °F.
Fan Mode - Use the menu to set the fixture fans to max. fan power mode ("High") or to auto- control mode
("Auto").
Theatre mode - The mode reduces max. pan/tilt and zoom speed in order to provide silent operation of the
fixture:
Pan range 0-450°: 3.4 seconds at max. speed.
Tilt range 0-300°: 2.5 seconds at max. speed.
Zoom min-max: 10 seconds at max speed
Date & Time Settings - Use this menu to set current date and time for the fixture log system (menu "View
Logs"). Set this menu item before first fixture operation.
Default Settings - The menu item allows to set all fixture parameters to the default (factory) values.
25
7.4 Tab "Manual Control"
Reset Functions - The menu allows to reset the fixture either per function modules or all modules together.
Total System Reset - The item resets all function modules.
Pan/Tilt Reset - The item resets a pan and tilt movement.
Zoom Reset - The item resets a zoom module.
Preset Effect Control - Use the menu to show preset positions of each channel effect.
Manual Effect control - Use the menu to control all fixture channels by means of the control panel.
7.5 Tab "Stand-alone"
Test Sequences -Use the menu to run a test/demo sequences without an external controller, which will show
you some possibilities of using Robin 800 LEDWash.
Dynamic Mode - This mode uses all Robin 800 LEDWash functions including pan/tilt movement and therefore
is good for a complete introduction of the fixture.
Static Mode - This mode is suitable for projections on the wall, ceiling or ground without any pan/tilt movement. Adjust the pan, tilt and zoomto desired positions an start test sequences by touching the green icon.
Music Trigger - Use the item to activate the sound control of the running program via the built-in microphone.
Preset Playback - This menu allows you to select the program which will be played in a loop after switching
the fixture on (the option is commonly used in a stand-alone operation without an external controller).
None - The option disables “Presetting playback” function.
Test - The option starts the test sequences.
Prog. 1 - The option starts user program No. 1.
Prog. 2 - The option starts user program No. 2.
Prog. 3 - The option starts user program No. 3.
Play program - Use the menu to run desired program in a loop.
Play Program 1 - The option starts user program No.1.
Play Program 2 - The option starts user program No. 2.
Play Program 3 - The option starts user program No. 3.
Edit Program - Use the menu to create or to edit desired program. The Robin 800 LEDWash offers 3 free
programs, each up to 100 steps.
Edit Program 1 - The option allows to edit user program No.1.
Edit Program 2 - The option allows to edit user program No.2.
Edit Program 3 - The option allows to edit user program No.3
To edit program:
1. Touch the item which you want to edit (“Edit Program 1” - “Edit Program 3”).
2. Touch the item "Edit Program Steps".
3. Touch the item "Step 1".
4 From the list of effects touch desired effect and set its value. Browse throw the list by touching the [up arrow]
and [down arrow] and set all desired effects.
An item "Step Time" (value of 0-25.5 sec.) is the time during which effects last in the current step
5. Save adjusted effects to the current step by touching the [confirm] or save and copy them to the following
step by touching the [confirm+copy]. By touching the text box "Preview" next to the current program step you
can view created scene.
6. Repeat the steps 4 and 5 for next program steps.
7. After editing desired program steps, adjust the length of the program by touching the text boxes "Start Step"
and "End Step".
Meaning of the icons used in the "Edit Program" menu:
26
- moves down on the next page
- saves adjusted values and leaves menu
- moves up on the previous page
- saves values to the current step and copy them to the
following prog. step
- leaves menu without saving values
There is a chart describing behaviour of items "Pan/Tilt Macro" and "P./T. Macro Speed".
DMX
0-9
10 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
Pan/Tilt Macro
Disabled pan/tilt macro
Reserved
Figure of circle (from small to large)
Figure of horizontal eight (from small to large)
Figure of vertical eight (from small to large)
Figure of rectangle (from small to large)
Figure of triangle (from small to large)
Figure of star (from small to large)
Figure of cross (from small to large)
0
1 - 127
128 - 129
130 - 255
Pan/Tilt Macro Speed
No macro generation
Macro generation from fast to slow-forwards
No macro generation
Macro generation from slow to fast-backwards
7.6 Tab "Service"
Adjust DMX Values - The menu allows you to set all effects to desired positions before fine calibration of the
effects .
Calibrations - This menu enables fine calibration of fixture effects and download default calibration values.
Calibrate Effects - The menu allows the fine adjustment of effects.
Pan- a pan position fine adjustment
Tilt - a tilt position fine adjustment
Beam shaper- a beam shaper module
By using these items you can calibrate and adjust effects to desired positions.
Calibration of the pan/tilt via the control board
1. Disconnect DMX controller from the fixture and enter the "Calibrate Effects" menu.
2. Use the [up arrow] and [down arrow] to find "Pan" and touch it to enter the fine effect adjustment screen.
3. Set desired value and save it by touching the [confirm].
4. Repeat steps 2 and 3 for next item.
5. After calibrating all effects, touch the [confirm] to save all adjusted values and reset the fixture.
Note: you can also use DMX controler for fine calibration of effects
Effect
Mode 1
Pan-fine movement
channel 20
Tilt - fine movement
channel 21
Beam shaper-fine mov. channel 22
Mode 2
channel 14
channel 15
channel 16
Mode 3
channel 15
channel 16
channel 17
Mode 4
channel 12
channel 13
channel 14
Mode 5
channel 20
channel 21
channel 22
Load Default Calibrations - The item loads default (factory) calibration values.
Updating software - The menu item allows you to update software in the fixture via either serial or USB port
of PC.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP or Linux
- DMX Software Uploader
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
27
Note 1: Software update should execute a qualified person. If you lack qualification, do not attempt the update
yourself and ask for help your ROBE distributor.
Note 2: DMX address, IP address, programs 1-3 and all items in the menu "Personality" will be set to their
default (factory) values.
To update software in the fixture:
I. Installation of the DMX Software Uploader.
1. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3. Unpack the program from the archive. If the Robe fixture is produced in both magnetic
and electronic ballast version, name of DMX Software Uploader is the same for both versions.
II.Fixture software updating.
1.Determine which of your ports is available on your PC and connect it:
- with the DMX input of the fixture if you using the flash cable RS232/DMX
- with the DMX output of the Robe Universal Interface if you using the USB cable.
Disconnect the fixture from the other fixtures in a DMX chain. Turn both the computer and
the fixture on. Make sure the lamp is switched off (only if the fixture involves a lamp).
2. Switch the fixture to the updating mode by touching the "Updating Software " item
Note: If you do not want to continue in software update, you have to switch off and on the fixture
to escape from this menu.
We recommend to cancel all running programs before starting the Software Uploader.
3. Run the Software Uploader program. Select desired COM and then click on the Connect button.
(Select COM if the serial port is used or Robe Universal Interface if the USB port is used).
If the connection is OK, click on the “Start Uploading button“ to start uploading. It will take several
minutes to perform software update.
If the option "Incremental Update" is not checked, all processors will be updated (including
processors with the same software version).
If you wish to update only later versions of processors, check the “Incremental Update box“.
Avoid interrupting the process. Update status is being displayed in the Info Box window.
When the update is finished, the line with the text “The fixture is successfully updated“ will appear in
this window and the fixture will reset with the new software.
Note: In the case of an interruption of the upload process (e.g. power cut), the fixture keeps the updating mode
and you have to repeat the software update again.
8. RDM
This fixture supports RDM operation. RDM (Remote Device Management) is a bi-directional communications
protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and
status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting
existing non-RDM equipment. By using a special „Start Code,“ and by complying with the timing specifications
for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive
messages from specific moving lights.
RDM allows explicit commands to be sent to a device and responses to be received from it.
The list of commands for Robin 800 LEDWash is the following.
Parameter ID
Discovery command SET command
DISC_UNIQUE_BRANCH
*
DISC_MUTE
*
DISC_UN_MUTE
*
GET command
DEVICE_INFO
*
SUPPORTED_PARAMETERS
*
SOFTWARE_VERSION_LABEL
*
DMX_START_ADDRESS
*
*
IDENTIFY_DEVICE
*
*
DEVICE_MODEL_DESCRIPTION
*
MANUFACTURER_LABEL
*
28
*
DEVICE_LABEL
*
SENSOR_DEFINITION
*
SENSOR_VALUE
*
DISPLAY_INVERT
*
*
DISPLAY_LEVEL
*
*
PAN_INVERT
*
*
TILT_INVERT
*
*
DEVICE_RESET
*
DMX_PERSONALITY
*
*
DMX_PERSONALITY_DESCRIPTION
*
STATUS_MESSAGES
*
STATUS_ID_DESCRIPTION
*
DEVICE_HOURS
*
PARAMETER_DESCRIPTION
*
ROBE_DMX_INPUT
*
ROBE_WIRELESS_UNLINK
*
*
9. Error and information messages
Occurred errors during fixture operation are signalled by the yellow warning icon at the bottom line of the
screen:
Touch the warning icon or press the [ESCAPE] button to display error messages.
List of error and information messages:
Temper.Sensor Error
The message informs you that the communication betwen the head temperature sensor and the main processor failed.
Tilt Error 1 (Tilt Error 2)
This message will appear after the reset of the fixture if the head´s magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The head is not
located in the default position after the reset.
Pan Error 1 (Pan Error 2)
This message will appear after the reset of the fixture if the yoke´s magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The yoke is not
located in the default position after the reset of the fixture.
Faulty battery
The battery on the display board is exhausted and should be replaced immediately.
29
10. Technical Specifications
Electrical
Power supply:.........................electronic auto-ranging
Input voltage range:............... supply 100-240V, 50/60Hz
Fuse:.......................................T 4 A@230V
Power consumption:................430W@230V, power factor=0.98
Optic
LED zones
Light source: 37 Osram Ostar DLmultichips
3 zones with individual colour control of each
Typical Lumen Maintenance: 70% @ 60,000 hours
LED life expectancy: 60.000 hours
Beam shaper 8° x°26° (half beam) installed in fixture
pre-defined zone effects
Zone effects in both directions with variable speed
Strobe
All LED zones together:
Strobe effect with variable speed (0.3 - 20Hz)
Random strobe pulse-effect with variable speed
Opening/closing pulse effect with variable speed
Independent strobe effect with variable speed (0.3 - 20Hz) at LED zone 3
Random strobe and random LED zone effect
Dimmer
Smooth dimmer from 0 - 100 %
Zoom
Motorized, 8°-63°
Pan/Tilt
Control
Pan movement range: 450°
Tilt movement range: 300°
16 bit movement resolution
Automatic Pan/Tilt position correction
Remotely controllable speed of pan/tilt movement for easy programming
Movement control: tracking and vector
Graphic touch screen for fixture setting and addressing
Gravitation sensor for auto screen positioning
Battery backup of the touch screen
Readout fixture usage, receiving DMX values, temperatures, etc
Built-in analyzer for easy fault finding, error messages
Built-in demo sequences
Theatre mode for silent pan/tilt and zoom moving
Silent fans cooling,
Stand-alone operation
3 user editable programs, each up to 100 steps
Supported protocols: USITT DMX 512, RDM, ArtNet, MANet, MANet2
6 DMX modes (19, 13, 14, 11,19, 18 control channels)
30
Wireless DMX/RDM module
Compliance with USITT DMX-512 (1986 & 1990) and 512-A
Full DMX fidelity and frame integrity
Auto sensing of DMX frame rate and frame size
<5ms DMX latency
Operational frequency range of 2402-2480 MHz
Producer: LumenRadio
Connection
DMX data in/out: Locking 3-pin and 5-pin XLR
AC power input: Chassis connector Neutrik PowerCon, A-type, NAC3MPA
Cable connector Neutrik PowerCon, A-type, NAC3FCA , for power-in, (installed on
the power cord)
Ethernet: RJ45
Rigging
Mounting points: 2 pairs of 1/4-turn locks
Mounting horizontally or vertically via 2 Omega brackets
Mounting adapter for one Omega bracket
Temperatures
Maximum ambient temperature : 45° C
Maximum housing temperature : 75° C
Minimum distances
Min. distance from flammable surfaces: 0.5 m
Min. distance to lighted object: 1.0 m
Total heat dissipation
1330 BTU/h (calculated)
Weight (net):
11 kg (with beam shaper)
10.7 kg (with front transparent cover)
Dimensions (mm)
31
Accessories
Omega holder (P/N.99010420).........................................................2 pcs
Front clear transparent cover (P/N. 99013603..................................1 pc
Optional accessories
Top hat-black (No.10980101)
Top hat-white (No.10980103)
Top hat-silver (No.10980111)
Mounting adapter for one Omega holder in black (No.10980100)
Mounting adapter for one Omega holder in neutral - glazy aluminium (No.10980113)
Beam shaper module 19°x35 ° (No.10980142)
EggCrate Robin 800 LEDWash-black (No. 10980199)
Mounting adapter for
one Omega holder
11. Maintenance and cleaning
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build
up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will
not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances
should alcohol or solvents be used!
DANGER !
Disconnect from the mains before starting any
maintenance work
The head´s transparent cover will require weekly cleaning as smoke-fluid tends to building up residues, reducing the light-output very quickly. The cooling fans should be cleaned monthly.
The interior of the base should be cleaned at least annually using a vacuum-cleaner or an air-jet.
More complicated maintenance and service operations are only to be carried out by authorized distributors.
11.1 Replacing fuse
IOnly replace the fuse by a fuse of the same type and rating.
Before replacing the fuse, unplug mains lead!
If you need to replace the main fuse, follow the instrustions:
1) Remove the rear cover of the base by unscrewing 6 fastening screws.
2) Remove the old fuse from the fuseholder.
3) Install the new fuse into the fuseholder.
4) Replace the rear cover back to the base.
32
12. ChangeLog
This section summarizes all types of changes in the user manual.
Version of the
manual
1.1
Date of issue
17/1/2013
Description of changes
Added photometric diagrams
Specifications are subject to change without notice.
April 20, 2016
33
13. Photometric diagrams
34
35
36
37
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising