owner`s manual - cloudfront.net

owner`s manual - cloudfront.net
California Outdoor Concepts, Inc.
17671 Irvine Blvd., Suite 108
Tustin, CA 92780
Telephone 877-274-6773
Fax 877-274-0017
Monterey, Tradewinds
Elegant, Carmel
Del Mar, Palm
San Simeon,
Water Features,
Solano, La Costa
OWNER’S MANUAL
OUTDOOR LIVING REDEFINED TM
SAFE AND BEAUTIFUL OUTDOOR FIREPIT
FOR PROPANE AND *NATURAL GAS
Report # 516-O-02-4
Installer: Leave This Manual with Consumer
Consumer: Save this Manual for Future Reference
CODE AND SUPPLY REQUIREMENTS: This Outdoor Fire Pit must be installed in accordance with
local codes and ordinances, or in the absence of local codes, with the latest National Fuel Gas Code.
ANSI Z223.1. When an appliance is for connection to a fixed piping system, the installation must
conform with local codes, or in the absence of local codes, the National fuel Gas Code, ANSI
Z223.1/NFPA 54, or International Fuel Gas Code.
WARNING: improper installation, adjustment,
alteration, service or maintenance can cause
injury or property damage. Read the installation,
operating and maintenance instructions
thoroughly before installing or service this
equipment.
WARNING:
For Outdoor Use Only.
WARNING
DANGER
IF YOU SMELL GAS:
1. Shut off the gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance
and immediately call your gas supplier or fire
department.
DANGER
Do not store or use gasoline or
other flammable vapors and
liquids in the vicinity of this or
any other appliance.
An LP-cylinder not connected for
use shall not be stored in the
vicinity of this or any other
appliance.
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide
which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space
such as a camper, tent, car or home.
California Outdoor Concepts – TABLE OF CONTENTS
Cover – Important Safety Information.……………………….………………………………………………… 1
Table of Contents…….……………………………………….………………………………………………….. 2
Important Safety Information
Minimum Clearances to Combustibles………………………………………………………..……… 2
Pre-Installation & Preparation Guidelines……………………………………………………..……... 3
Installation Information
Connecting the Gas to the Campfire……………………………………………………………….…..4
Lava Granules and Logs Parts List..……………………………………………………………….…..4
Lava Granule & Log Placement………………………………………………………………….…………….…5
Arctic Flame Glass…………………………………………………………………………………………………6
Operating Instructions…………………………………………………………………………………………......7
Lighting Instructions………………………………………………………………………..……….…... 7
Operating Information…………………………………………………………………………….…….. 8
Converting your Fire pit to a Different Gas Type……..………………………………………….……9
This fireplace is tested by OMNI-Test Laboratories, Portland Oregon and complies with:
ANSI Z21.97-2012/CSA 2.41-2012 “Standard for Outdoor Decorative Gas Appliances.”
IMPORTANT SAFETY INFORMATION
READ THESE INSTRUCTIONS FULLY BEFORE INSTALLING THIS OUTDOOR FIREPIT. If
not installed and used correctly per these instructions, this product can cause serious injury.
CAUTION: INSTALLATION, MODIFICATION AND REPAIR MUST BE DONE BY
A QUALIFIED, PROFESSIONAL INSTALLER.
Be sure you understand all safety precautions and warnings contained in this manual.
1. CHECK STATE AND LOCAL CODES TO DETERMINE IF THE OUTDOOR FIREPIT IS
PERMITTED IN YOUR LOCALITY BEFORE INSTALLATION.
2. FOR OUTDOOR USE ONLY. THIS UNIT MUST BE INSTALLED AT LEAST 60” FROM CENTER
OF BURNER TO ANY COMBUSTIBLE WALLS OR MATERIAL. IT MUST NOT BE INSTALLED
UNDER ANY TYPE OF CEILING OR OVERHANG.
3. When shutting the unit down—be sure to TURN THE KEY VALVE FULLY OFF.
4. WARNING: CARBON MONOXIDE POISONING MAY LEAD TO DEATH. DO NOT MODIFY
THIS OUTDOOR FIREPIT OR ITS CONTROLS, EXCEPT AS PROVIDED FOR IN THIS
MANUAL.
Any other change may be dangerous. Improper installation or use of your outdoor firepit can
cause serious injury or death from fire, burns, explosions or carbon monoxide poisoning.
MINIMUM CLEARANCE TO COMBUSTIBLES
The dimensions shown in Figure 1 are MINIMUM
CLEARANCES to maintain when you install this
outdoor firepit. THERE MUST BE AT LEAST 24”
of clearance from the side wall, 60” of clearance
from the ceiling, and 0” of clearance from the
floor.
Figure 1 2 IMPORTANT SAFETY INFORMATION
-INSTALLATION AND PREPARATION SAFETY GUIDELINES
1. Before installing this outdoor firepit, check “Minimum Clearance to Combustibles” on page 2.
MINIMUM CLEARANCES must be maintained when you install this outdoor firepit. THERE
MUST BE AT LEAST 24” from the side of appliance to any combustible materials.
2. The outdoor firepit is for outdoor use only. DO NOT install or use this appliance inside a building,
garage, or any other enclosed area including recreational vehicles and/or boats. This unit must
be installed in such a manner that proper air ventilation is maintained without obstruction.
At all times, and during all weather conditions.
3. CHECK GAS TYPE (natural gas or propane): The gas supply you intend to use may not be the
same as that stated on your outdoor firepit rating plate. THIS FIREPIT IS CONSTRUCTED FOR
USE WITH PROPANE GAS. If the gas supply is different, or if you wish to change to natural
gas, you MUST have the firepit converted (method described on page 8) to the gas type
you intend to use, by a qualified, professional installer. If you are unsure, contact your dealer
for assistance.
4. DO NOT USE IF GAS PRESSURE IS LOWER THAN THE MINIMUM REQUIREMENT OR
EXCEEDS THE MAXIMUM.
5. FOR NATURAL GAS: The minimum inlet gas supply pressure for purposes of input adjustment
is 5 inches water column and maximum inlet gas supply pressure is 10 inches water column.
FOR PROPANE: The minimum inlet gas supply pressure for purposes of input adjustment is 8
inches water column and the maximum inlet gas supply pressure is 13 inches water column.
6. Gas piping system must be sized to provide minimum inlet pressure at the maximum flow rate
(BTU/hr). Undue pressure loss will occur if the pipe is too small or the run is too long
7. For installations at elevations above 2,000 ft., contact your local dealer or gas supplier before
installing as input ratings should be reduced approximately 4% for each 1,000 ft. above sea level.
Refer to the National Fuel Gas Code. Contact the factory for the required orifice.
8. The outdoor firepit and its main gas valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of ½ psig. This is
accomplished by closing the gas supply line valve, as required by NFPA 54, section 5-54.
9. The outdoor firepit must be isolated from the gas supply piping system by closing its equipment
shut-off valve during any pressure testing of the gas supply piping system at test pressures equal
to or less than ½ psig.
10. INSTALLER NOTE: This unit should be installed so that it can be removed at a later date
for service.
11. GAS SUPPLY PLUMBING REQUIREMENTS Apply only joint compounds that are resistant to all
gasses on all male pipe fittings.
12. DO NOT BURN SOLID FUELS OF ANY KIND IN THIS APPLIANCE.
SAFETY NOTE: An external on/off valve in the gas line is required for safety when your Outdoor
Firepit is not in use. It also provides for convenient maintenance and repair.
INSTALLATION INFORMATION
CONNECTING THE GAS TO THE FIREPIT
IMPORTANT
BEFORE PROCEEDING, CAREFULLY READ ALL OF THE IMPORTANT SAFETY
INFORMATION CONTAINED IN THIS OWNER’S MANUAL, INCLUDING:
A. Pre-Installation and Outdoor Firepit Preparation Safety Guidelines (page 3).
B. Log installation Guidelines (page 4).
C. Minimum Clearance to Combustibles (page 2).
D. Examine your burner, if damage is evident replace only with a California Outdoor Concepts burner.
Cylinder Specifications:
20 lb (9.1 kg) propane cylinder constructed and marked in accordance with the U.S. D.O.T. Specifications
for L/P- Gas Cylinders, or the Standard for Cylinders, Spheres and Tube for Transportation of Dangerous
Goods and Commission, CAN/CSA B399.
BEFORE INSTALLATION, BE SURE THE PROPANE TANK IS TURNED OFF.







To connect to the propane gas tank, attach the black hose (with regulator) and tighten down the
connector (see photos below). Follow all instructions and safety warnings supplied with the propane
tank.
Propane cylinder must have a listed over-filling protection device.
Turn on the gas to the burner system and test for leaks with soapy water solution.
(Never use an open flame for testing). If a leak is found, tighten the connector until no leaks
are detected.
The hose should be inspected before each use of the appliance.
The hose assembly must be replaced prior to the appliance being put into operation if there is
evidence of excessive abrasion or wear, or if the hose is damaged. The replacement hose shall be
that specified by the manufacturer. Do Not Use Any Substitute Materials With This Appliance.
Properly locate the gas hose out of pathways where people may trip over it or in areas where the
hose may be subject to accidental damage.
TO GAIN ACCESS TO PROPANE CYLINDER:
1. Locate access door on appliance.
2. Use handle to pull door open, disconnecting magnetic latch.
BURNER MEDIA INSTALLATION
A. Carefully inspect the burner and log cartons for shipping damage. If any parts are missing or
damaged, call your dealer. Do not attempt to install the appliance unless all parts are in good
condition.
B. Correct installation is crucial to safe performance of your Outdoor Fire Pit.
C. Due to high temperatures, the Fire must be located out of traffic areas and away from combustibles.
LAVA GRANULES & LOG PARTS LIST
Replacement parts available from your local retailer.
LAVA AND LOG
BURNER MEDIA
LAVA GRANULE & LOG PLACEMENT
1. Pour the two bags of lava granules into the Outdoor Firepit so that it completely covers the burner.
(See figures #1 and #2)
2. Place the largest log diagonally centered over the burner. (See figure #3)
3. Place the other logs as desired using the first log (figure #3) as a support to lean the other logs against.
(See figure #4)
FIGURE 1
FIGURE 3
FIGURE 2
FIGURE 4
CAUTION:
BURN HAZARD. LOGS WILL REMAIN HOT FOR SOME TIME AFTER USE.
YOU MUST MAINTAIN THE LOG LAYOUT AS SHOWN TO ENSURE PROPER OPERATION OF
YOUR LOG SET. IF YOU NEED TO REPOSITION ANY LOG TO MAINTAIN THE PROPER LAYOUT,
USE HEAT RESISTANT GLOVES OR ALLOW LOGS ADEQUATE TIME TO COOL BEFORE
HANDLING.
Glass Burner Media
ARCTIC FLAME GLASS
1. Pour the bag(s) of ARCTIC FLAME GLASS into the Outdoor Firepit so that it completely covers the
burner. (See figures #1a and #2b)
2. Place all of the enclosed ARCTIC FLAME GLASS into the burner. Not using all of the glass may result
in a low flame.
Figure 1a
Figure 2b
OPERATION MANUAL
*We recommend that before you install your log set or glass you familiarize yourself with the control valve layout.
This will help you to be confident operating the log set when fully installed (see figures below for typical control
positions).
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
BEFORE LIGHTING, smell all around the
Outdoor Firepit area for gas. Be sure to smell
next to the floor because some gas is heavier
than air and will settle on the floor. IF YOU
SMELL GAS FOLLOW THE INSTRUCTIONS
ON PAGE 1.
DO NOT use this appliance if any part has been
under water. Immediately call a qualified,
professional service technician to inspect the
Outdoor Firepit and to replace any part of the
control system and any gas control that has
been under water.
Use only your hand to turn the gas key control.
Never use tools to turn the key. If the key will not
turn by hand, DO NOT try to repair it. Call a
qualified, professional service technician. Force
or attempted repair may result in fire or
explosion.
LIGHTING INSTRUCTIONS
STOP – READ SAFETY INFORMATION ABOVE.
1. Turn the manual gas control slightly and turn clockwise to the “OFF” position or
when you have a firm stop.
TURN VALVE
2. Wait 5 minutes for gas to clear out.
3. Place a burning match to the surface of the lava granules that cover the burner.
Do not hold the match by hand.
4. After the match is burning and in position, turn the gas control key slightly,
and slowly turn the key counter-clockwise to obtain the desire flame height.
ON
OFF
Control Konb
Shutting Off the Firepit
Turn off; rotate the manual gas control key clockwise to the “OFF” position or when you have reached a
firm stop
CAUTION: DO NOT turn the main gas valve key to the “ON” position FOR 45 SECONDS after closing.
OPERATING INSTRUCTIONS (continued)
OPERATING INFORMATION
A. Young children MUST be carefully supervised when in the vicinity of this appliance.
B. DO NOT sit or place any part of the body or combustible materials on the Firepit surround. Children
and adults should be alerted to the hazard of high surface temperatures and should stay away to
avoid burns or clothing ignition.
C. Every time you use your Firepit make sure that the area around the Firepit is clear of flammable items
such as gasoline, yard debris, wood, etc.
D. WARNING: HOT WHILE IN OPERATION AND FOLLOWING OPERATION. Children must be
carefully supervised when in the vicinity of this appliance. Serious injury and/or may occur. DO NOT
throw trash, paper, or other flammable materials onto your Firepit. DO NOT leave unattended while in
operation. WARNING: DO NOT operate the Firepit in the rain.
E. SOLID FUEL MUST NOT BE BURNED in the enclosure where your Firepit is installed.
F. DO NOT continue using if you smell unusual odors or have headaches, nausea or are dizzy.
G. DO NOT store any combustible materials, gasoline, and any other flammable vapors/liquids around
the area of your Firepit. Provide adequate clearance for servicing and operation.
H. DO NOT hang clothing or any flammable material on or near your Firepit. Matches, paper, garbage,
or any other material must not be thrown on top of the logs, burner, or into the flame.
I.
DO NOT use your Firepit if any part of it has been under water. Immediately call a qualified service
technician to inspect the set and to replace any part of the control system and any gas control which
has been under water.
J.
Installation and repair should be done by a qualified service person. The appliance should be
inspected before use and at least annually by a qualified service person. More frequent cleaning may
be required as necessary. It is imperative that control compartment, burners and circulating air
passageways of the appliance be kept clean.
K. Once a year, make a visual check of the burner and burner flames - see pictorial representation
on following page for proper flame height. To gain a proper line of site to check you burner,
remove the side door to see the burner. If necessary, the use of a flash light may be helpful.
L. Cleaning of appliance – Remove logs and lava granules or ARCTIC FLAME GLASS, clean burner
with soap and water and dry thoroughly. (To clean logs dust with feather duster or vacuum, never use
water to clean logs.
WARNING
If upon Inspection of burner, any damage is evident, burner must be replaced
prior to appliance being put into operation. Use only replacement parts specified
by manufacturer.
Ideal Flame Appearance
LP Tank Information
STOP – READ SAFETY INFORMATION BELOW
1. Other LP cylinders may be acceptable for use with your fire pit provided they are compatible
with your fire pit retention means and accompanied by illustrations depicting the cylinder
mounted to the appliance utilizing the cylinder retention means and the point of contact between
the cylinder and the retention means.
2. The LP gas supply cylinder to be used must be constructed and marked in accordance with the
U.S. Department of Transportation (D.O.T.) Specifications for LP Gas Cylinders, Spheres and
Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA B339 as applicable.
3. The LP cylinder must be provided with a listed overfilling prevention device.
4. The LP cylinder must be provided with a cylinder connection device compatible with the
connection of your fire pit.
CONVERTING YOUR FIREPIT TO A DIFFERENT GAS TYPE
To convert your Firepit from propane to natural gas or natural gas to propane gas, carefully follow the
steps below:
1. MAKE SURE THAT THE GAS SUPPLY TO THE FIREPIT (AND ANY NEARBY ELECTRICAL
SOURCES/APPLIANCES) ARE SHUT OFF AND UNPLUGGED.
2. Remove all logs and lava rock or glass burner media from the Firepit enclosure and remove the
decorative top.
3. Remove the burner pan from your fire ring or enclosure.
4. Carefully detach the connector hose attached to the orifice holder and unscrew the orifice holder from
the burner pipe.
5. Remove the orifice from the holder and replace it with the proper sized one for your gas
requirement. Propane requires the smaller orifice.
6. If you are converting from natural gas (NG), to propane (LP) gas, slide the air shutter so that the air
intake hole is open. For natural gas, slide the air shutter so that the air intake hole is closed.
7. For natural gas (NG), you must install a gas pressure regulator. Adjust gas pressure regulator to 7
inches water column.
Gas Parts Drive Train
California Outdoor Concepts * Parts List

Burner Pan
Part # 804

Orifice with Air Mixer
Part # 803

Connector Hose
Part # 812

Valve
Part # 805

Nipple
Part # 809

Brass Jam Nut
Part # 811

Gas Knob
Part # 807

Hose and Regulator Assembly
Part # 812
Replacement Parts are Available from Your Dealer
THE
ORIGINAL
FIREPIT
TABLE
TM
COMPANY
2020 Del Mar Dining
4040 La Costa Del Rio
1010 Salono Chat
1020 Salono Dining
1030 Salono Bar
2010 Del Mar Chat
2030 Del Mar Bar
2050 Del Mar Balcony
4010 La Costa Chat
4020 La Costa Dining
5010 Carmel Chat
7010 San Simeon Chat
7110 Monterey
7140 Monterey Coffee Table
7210 Island
7310 Palm Chat
7320 Palm Dining
7330 Palm Bar
7410 Tradewinds Chat
7420 Tradewinds Dining
7430 Tradewinds Bar
7520 La Jolla
7550 La Paz
7610 El Paseo
Use your smart
phone QR code
reader to view
7611 Rodeo Chat
7651 Rodeo Balcony
Follow us on Facebook
and Twitter
17671 Irvine Blvd.
Suite 108
Tustin, CA 92780
Toll Free (877)-274-6773
Fax (877)-274-0017
www.californiaoutdoorconcepts.com
Codes and Gas Requirements:
When an appliance is for connection to a fixed piping system, the installation must conform to
local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI
Z223.1/NFPA 54; International Fuel Gas Code, Natural Gas and Propane Gas Installation Code,
CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable.
For appliances with a fixed fuel piping system and equipped with an appliance gas pressure
regulator, the appliance and its individual shut off valve must be disconnected from gas supply
piping system during any pressure testing of that system at pressures in excess of ½ psi (3.5
kPa).
The appliance must be isolated from gas supply piping system by closing its individual manual
shut off valve during any pressure testing of the gas line at test pressures equal to, or less than
½ psi (3.5 kPa).
LP Gas
Normal Gas Pressure
Burner Orifice Size
BTU/ hr
MANUFCTURER”S USE ONLY
A. Quality Check:
B. Orifice # (MAIN):
C. Orifice #(OTHER):
D. Leak Test:
E. Burn Test:
F. Gast Type:
G. Model #:
H. Serial #:
I.
Air Shutter:
J.
Inspector:
11” WC
#39
64,000
NG Gas
7” WC
#13
64,000
DATE_______________
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising