PVVEX 58/510-300 Roof Power Vent System

PVVEX 58/510-300 Roof Power Vent System
Installation & Maintenance Manual
PVVEX58-300 &
PVVEX510-300
5/8 and 5/10
External Roof
Power Vent
WARNING
If the information in these instructions is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
NOTICE
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
NOTICE
DANGER
NOTICE
Blank
IF YOU SMELL GAS
PVHEX58-300
vent
approved for use with Montigo R320, R320-ST, R420,
Do not trypower
to light
anyisappliance.
R420-ST,
RP620.
Do and
not touch
any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier, call the fire department.
Blank
Flammable materials
Toxic
Corrosive
Danger overhead crane
Blank
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
General Warning
Laser Radiation
Explosion risk
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Corrosive
Danger overhead crane
Fork lift trucks
Hot surface
Flammable materials
Explosion risk
General Warning
Laser Radiation
Biohazard
Slippery floor
Watch your step
Irritant
Toxic
Oxidising
Cutting
Fork lift trucks
High voltage
PVHEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.
NOTICE
This power vent is approved for use with Montigo fireplaces only and is certified to
ANSI Z21.50 / CSA 2.22 vented gas fireplace standard along with the fireplace.
High voltage
Danger of entrapment
Danger of death
High temperatures
Glass hazard
Danger of suffocation
Hot surface
Danger of entrapment
Danger of death
Glass hazard
Danger of suffocation
Battery hazard
Rotating parts
Blank
General Warning
Laser Radiation
Biohazard
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Gas bottles
Watch for
falling objects
Explosion
risk
Electricity
Danger for cutter
Entrapment hazard
Corrosive
Danger overhead crane
Flammable materials
Toxic
Oxidising
Fork lift trucks
High voltage
Glass hazard
Danger of suffocation
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Gas bottles
Watch for
falling
objectsfield
Strong
magnetic
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Optical radiation
Laser Radiation
Biohazard
Non ionizing
radiation
Oxidising
Radiation
General Warning
Hot surface
Hazardous to the
Environment
Danger of entrapment
Danger of harming
your hands
Danger of death
Gas bottles
Watch for
falling objects
Strong magnetic field
Electricity
Danger for cutter
Optical radiation
Entrapment hazard
Battery hazard
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Gas bottles
Watch for
falling objects
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Rotating parts
NOTICE
NOTICE
PVVEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.
PVVEX58-300 power vent is approved for use with Montigo R320, R320-ST, R420,
R420-ST, and RP620.
XG0518
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
NOTICE
140707.2
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Safety Alert Key
Introduction
Specifications
Pipe Dimensions PVVEX58-300 ............ 5"/8"
Pipe Dimensions PVVEX510-300 .......... 5"/10"
Maximum Airflow: .......................... 300 CFM
Speed: ........................................... 2700 RPM
Power: ............................................ Connect to fireplace control box
............................................. Refer to fireplace rating plate
Before Your Begin
General Information
This installation guide covers installation of the External Power Vent
System only. This system is designed to allow installation of gas fireplaces
that cannot be done with a standard Direct Vent gas fireplace installation. Only for use on R-Series, R-Series See-Through and RP-Series.
ONLY USE WITH APPROVED FIREPLACES - see fireplace installation manual.
Read through the fireplace's installation & maintenance manual, as it
must also be adhered to.
Power Cord Harnesses:
EPVH10 - 10 foot power cord and harness
EPVH20 - 20 foot power cord and harness
EPVH30 - 30 foot power cord and harness
EPVH40 - 40 foot power cord and harness
EPVH50 - 50 foot power cord and harness
EPVH60 - 60 foot power cord and harness
EPVH70 - 70 foot power cord and harness
EPVH80 - 80 foot power cord and harness
EPVH90 - 90 foot power cord and harness
EPVH100 -100 foot power cord and harness
For vent configurations and power vent locations,
refer to fireplace manual. Page 2
XG0518 - 140707.2
126
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
24"
610
Introduction
PVVEX58-300 Vertical Po
PVVEX58-300 Product Dimensions
1
"
2
419
16
ical Power Vent Termination
4"
10
24"
610
3
8" 18 8 "
202 466
7
"
8
174
6
24"
610
5"
126
1
"
2
267
10
17"
432
Top View
17"
432
1
16 "
2
419
Side View
PVVEX58-300 Vertical Power Vent Termination
3
"
8 8"
466
202
18
3
"
8
66
8
24"
610
17"
432
24"
610
7
"
8
174
6
1
10 "
2
267
Bottom View
17"
432
5"
126
1
Figure 1. PVVEX58-300 &16
PVVEX510-300
(Tolerance ± ⅛") [mm]
"
2
419
XG0518 - 140707.2
3
"
8
466
18
Page 3
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Installation
PVVEX510-300 Vertical Power Vent Termination
10"
253
24"
610
5"
126
24"
610
1
"
2
419
16
3
"
8
466
18
7
"
8
175
6
13"
330
18"
458
18"
458
Figure 1a. PVVEX58-300 & PVVEX510-300 (Tolerance ± ⅛") [mm]
Page 4
XG0518 - 140707.2
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Installation
Step 2: Install the electrical harness (EPVH-10-100) that will communicate with the Power Vent. Run vent pipe from the fireplace to the
chase. Make sure the last section is female end up and is flush with
the top of the chase without going above it. See figure 2b.
Power Vent
Components
Installing
the power vent
Power Head
Vent Clamp
Framing Box
Vent
Chase
Figure 2. Power vent components Exploded View
Step 1: Construct a chase box around the vent penetration with
dimensions as shown in figure 2a.
20"
Max
PVVEX58-300
5
10 "
8
270
Min
Figure 2b.
Installing the Rough-in Kit.
Step 3: Remove the last section of vent pipe and put off to the side
to be used later. Take the rough in box from the power
PVVEX510-300
13"
[330]
20"
Max
24
Min
5
"
8
270
Min
10
Figure 2a.
Chase box dimensions
Figure 2c.
Installing the Rough-in Kit.
Note: Follow local and/or national code requirements for roof
clearances.
XG0518 - 140707.2
Page 5
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Installation
Step 4: Unscrew 6 screws securing the control cable cover and
remove it.
Step 6: Loosen nut on the strain relief of the control cable. Pass
control cable through slot in rough in box making sure the nut stays is
on the opposite side of the rough in box as the strain relief.
Figure 2g. Figure 2d. Unscrewing control cable cover
Step 7: Push the strain relief through the hole in the roughin box.
Figure 2h. Figure 2e. Removing control cable cover
Step 8: Reinstall the strain relief plate. Make sure the strain relief nut
is above the strain relief plate.
Step 5: Unscrew 2 screws securing strain relief plate and remove it.
Strain Relief Plate
Figure 2f. Removing strain relief plate. Page 6
Figure 2i. XG0518 - 140707.2
Install the vent pipe female end up 2"
- 3" from the top of the chase box.
PVVEX58-300
PVVEX510-300harness
External Roof(EPVHPower Vent
Install
the &electrical
10-100) that will communicate with
the Power Vent module.
Installation
Step 12: Drop the rough in box over top of and inside the Chase.
Step 9: Tighten the nut on the strain relief.
Step #3
Install the power vent Rought-in Kit.
Remove the electrical cover plate
from inside of the rough in kit. Pull
the control cable through the slot in
the bottom of the box and insert the
Figureinto
2j. the rectangular hole in the
plug
cover
cover
Step 10:plate.
Push the Re-attach
molex connector ofthe
the control
cable through the
hole in the
control
cable cover.
Make sure
the molex clicks
in place so
plate.
Pull
wire
harness
throught
the
it
does
not
fall
out.
supplied hole in the bottom corner of
the rough-in box and snap into the
slot provided.
Clicks Here
Figure 2m. Step 13: Take the last section of pipe and install the vent clamp
around the pipe. The bottom of the band should be 6 3/8" from the top
of the pipe. Tighten the clamp using the supplied nut and screw.
6 3/8"
Figure 2k. Step 11: Screw control cable cover back in place.
Figure 2n. Figure 2l. XG0518 - 140707.2
Page 7
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Installation
Step 14: Drop pipe down into the frame box. The pipe should be
flush with the top of the frame box. Secure pipe connection below.
Step 16: Place power vent over chase and fasten with 4 screws on
the vertical sides of the base plate. Silicone of seal the base plate in
any location necessary to keep the structure of the building free of
water or moisture.
Step #4
Place termination head over chase
and fasten with 4 screws on the
vertical sides of the base plate.
Silicone or seal the base plate in
any location necessary to keep the
structure of the building free of
water or moisture.
Figure 2o. Attachment
screw locations
Attachment
screw
locations
Step 15: Connect power cable of termination to the molex of the
control cable.
Figure 2q.
Installing the Rough-in Kit.
Wiring Installation
Conduit & Wiring clearances
Connect the power vent harness as outlined. Connect the wiring to
the fireplace as outlined in the schematic shown in figure 4. Ensure
that the proper clearances are maintained for the wiring and conduit.
When installing the wiring it must never run above the vent pipe and
it must be at least 1" clear of all venting and other hot surfaces.
Wire
1” Clearance
Figure 3. Conduit and Wiring
Figure 2p. Page 8
XG0518 - 140707.2
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Power
Vent Wiring
Installation
6 PIN MOLEX
CONNECTOR
GREEN
BLUE
BLACK
BROWN
C
BLACK
WHITE
KEY WAY
Figure 4. Power Vent Wiring Diagram
XG0518 - 140707.2
Page 9
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Installation
Power Vent Locations
V
Horizontal
Detail
Vertical Detail
Location
Canada*
USA**
A
clearance to the termination frame above grade, veranda, porch, deck, or balcony
30 inches
30 inches
B
clearance to top of doors or operable windows
12 inches
12 inches
C
clearance to sides or bottom of door or operable windows
4 feet
4 feet
D
clearance to permanently closed window when installed with approved glass penetration termination
0
0
E
clearance to permanently closed window Recommended to prevent condensation
30 inches
30 inches
F
clearance to ventilated soffit located within a horizontal distance to 24 inches from centerline
22 inches
22 inches
of termination
G
clearance to unventilated soffit
30 inches
30 inches
H
clearance to outside corner
30 inches
30 inches
I
clearance to inside corner
30 inches
30 inches
J
clearance to each side of the vertical centerline of a metre or regulatory assembly to a maximum
vertical distance of 15ft
3 feet
3 feet
K
clearance to service regulator vent outlet
3 feet
3 feet
L
clearance to non mechanical air supply inlet to the building or combustion air inlet to other
12 inches
4 feet
6 feet
4 feet
6 feet
3 feet above air inlet
appliance for appliance <= 100.000 BTU/H (30 KW)
L
clearance to non mechanical air supply inlet to the building or combustion air inlet to other
appliance for appliance > 100.000 BTU/H (30 KW)
M
clearance to forced air supply inlet
N+
clearance above paved sidewalk or paved driveway located on public property
P++
clearance under veranda, porch, deck, or balcony
7 feet
7 feet
30 inches
30 inches
Q
clearance above roof
See Fireplace Installation Guide
See Fireplace Installation Guide
R
clearance to adjacent walls and neighboring buildings
See Fireplace Installation Guide
See Fireplace Installation Guide
S
clearance from corner in recessed location
30 inches
30 inches
T
Maximum depth of recessed location
48 inches
48 inches
U
Maximum width for back wall of recessed location
V
Horizontal clearance between two terminations that are level
W
Horizontal clearance (centre to centre) between two terminations that are not level
60 inches
60 inches
See Fireplace Installation Guide
See Fireplace Installation Guide
30 inches
30 inches
* Based on CGA B149.1 Natural Gas and Propane installation code. Local codes may vary, please check with local regulatory agency.
** Based on ANSI Z223.1/NFPA 54 National Fuel Gas Code. Local codes may vary, please check with local regulatory agency.
+ A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serve both dwellings.
++ Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
Page 10
XG0518 - 140707.2
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Service
Capacitor Removal and Servicing
Capacitor Replacement [REC1252]
Step 3: Unscrew ground wire/capacitor bracket from motor.
WARNING: Save this screw.
Turn off power and gas before servicing.
Step 1: Remove the 4 outer screws that fasten the top cover to the
termination. Remove the cover.
Top Cover
g
Top Cover
Screws x 4 plcs
Figure 5b.
Step 4: Cut brown wire from motor and black wire from capacitor.
Figure 5.
Step 2: Cut zap straps.
Screw Locations
x 4 plcs
Wind Baffle
Rain Skirt
Figure 5c.
Step 5: Cut black fibre wire from power cable and blue wire from
motor.
Top Separator
Screw
Locations
Figure 5a.
x 5 plcs
Figure 5d.
XG0518 - 140707.2
Page 11
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Service
Step 6: Cut white fibre from power cable, black wire from capacitor
and black wire from motor.
Step 9: Using a small bell connector, connect the blue wire from the
motor to the black fibre wire from the power cable.
Figure 5e.
Step 7: Remove and dispose of old capacitor and open REC1252
Figure 5h.
Step 10: Using the large bell connector, attach the white fibre wire
from the power cable to the black wire from the motor and a black
wire from the capacitor.
Figure 5f. REC1252
Step 8: Strip ends of all cut wires and new capacitor. Screw new
capacitor and ground wire to the motor using the existing screw you
saved.
Figure 5i.
Step 11: Using the other small bell connector attach the brown wire
from the motor to the other black wire from the capacitor.
Figure 5g.
Figure 5j.
Page 12
XG0518 - 140707.2
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Service
Step 12: Zap strap wires together in a neat bunch so that no wires
can fall into the motor.
Step 14: Test the power vent and make sure it is working properly.
When looking down at the top of the motor the fan should be spinning
counterclockwise. If it is spinning the wrong way or not at all it is wired
incorrectly. Put the top cover back on using the supplied replacement
screws.
PVVEX58-300
Motor Removal / Servicing
Step 1:
Top Cover
Top Cover
Screws x 4 plcs
a) Remove the 4 outer screws
that fasten the Top Cover to
the termination
Figure
b)5k.Remove the Cover.
Step 13: Zap strap wires to loop in the top of the capacitor.
Figure 5m.
Step 2:
a) Remove the 4 outer screws
that fasten the Wind Baffle to
the termination.
b) Lower the Wind Baffle to
rest on the Rain Skirt.
Screw Locations
x 4 plcs
Wind Baffle
Figure 5l.
Rain Skirt
Step 3:
a) Remove the 5 outer screws
that fasten the Top Separator
to the termination.
b) Remove the Top Separator.
XG0518 - 140707.2
Top Separator
Screw Locations
x 5 plcs
Page 13
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Service
Motor and Capacitor Replacement
[REC 1253]
Turn off power and gas before servicing.
Step 1: Remove the 4 outer screws that fasten the top cover to the
termination. Remove the cover.
Top Cover
ng
g
ng
ws
os
ws
to
s
to
ws
or
s
or.
or
r.
Step 4: Cut 4 zap straps
Top
Top Cover
Cover
Top Cover
Screws x 4 plcs
Top
TopCover
Cover
Screwsxx44plcs
plcs
Screws
Figure 6c.
Figure 6.
Step 5: Remove the ground screw holding the ground wire and
capacitor.
Step 2: Remove the 4 outer screws that fasten the wind baffle to the
termination. Lower the wind baffle to rest on the rain skirt.
Screw Locations
x 4 plcs
Screw Locations
x 4 plcs
Screw
Locations
Wind
Baffle
x 4 plcs
Wind Baffle
Wind Baffle
Rain Skirt
Rain Skirt
Rain Skirt
Figure 6a.Top Separator
Figure 6d.
Step 6: Cut the black fibre wire from the power cable.
Step 3: Remove the 5 outer screws that fasten the top separator to
the termination.
Remove the top separator.
Top Separator
Screw Locations
x 5Top
plcsSeparator
Screw Locations
x 5 plcs
Screw Locations
x 5 plcs
Figure 6e.
Figure 6b.
Page 14
XG0518 - 140707.2
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Service
Step 7: Cut the white fibre wire from the power cable.
REC1253
Figure 6f.
Step 8: Remove 4 screws securing the motor mounting plate.
Figure 6i.
Step 10: Drop new motor assembly into the power vent and screw
with supplied 4 screws and star washers. Line up cut out in motor
mounting plate with electrical conduit.
Figure 6g.
Step 9: Lift out motor and capacitor.
Figure 6j.
Step 11: Remove the ground wire screw from the motor. NOTE:
Save this screw for later.
Figure 6h.
Figure 6k.
XG0518 - 140707.2
Page 15
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Service
Step 12: Using the ground screw, screw the capacitor bracket and
the ground wire to the motor.
Step 15: Using the other small bell connector, connect the other
black wire from the capacitor to the brown wire from the motor.
Figure 6l.
Figure 6o.
Step 13: Strip the ends of all the wires. Using the large bell connector, connect the white fibre wire from the power cable to the black wire
from the motor and one of the black wires from the capacitor.
Step 16: Using a zap strap to bundle the wires neatly together.
Figure 6m.
Step 14: Using a small bell connector, connect the black fibre wire
from the power cable to the blue wire of the motor.
Figure 6p.
Step 17: Using another zap strap, secure the bundle to the capacitor.
Figure 6n.
Figure 6q.
Page 16
XG0518 - 140707.2
Top Cover
Screws x 4 plcs
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
ws
o
ws
to
cing
ws
tor
ws
or.
o
ws
e to
o
ws
Service
Step 18: Using the last two zap straps secure the wires to the leg of
the motor. Make sure none of the wires can get caught in the motor.
Step 21: Test the power vent and make sure it is working properly.
When looking down at the top of the motor the fan should be spinning
counterclockwise. If it is spinning the wrong way or not at all it is wired
incorrectly. Put the top cover back on using the supplied replacement
screws.
PVVEX58-300
Motor Removal / Servicing
Screw Locations
x 4Step
plcs 1:
Top Cover
Top Cover
Screws x 4 plcs
Wind
a)Baffle
Remove
the 4 outer screws
that fasten the Top Cover to
the termination
b)
Remove
the Cover.
Rain
Skirt
Figure 6r.
Step 19: Reinstall the top separator with 5 supplied screws.
Top Cover
Top Separator
Figure 6u.
Screw
Locations
Top Cover
x Screws
5 plcs x 4 plcs
Step 2:
a) Remove the 4 outer screws
that fasten the Wind Baffle to
the termination.
b) Lower the Wind Baffle to
rest on the Rain Skirt.
Figure 6s.
Step 20: Reinstall the wind baffle with supplied screws.
Screw
Locations
Step
3:
x 4 plcs
a) Remove the 5 outer screws
the Top Separator
to the termination.
b) Remove the Top Separator.
Wind
Baffle
that
fasten
Screw Locations
x 4 plcs
Wind Baffle
Rain Skirt
Top Separator
Screw Locations
x 5 plcs
Rain Skirt
Figure 6t.
Top Separator
XG0518 - 140707.2
Page 17
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Appendix
Appendix A: Warranty
The Warranty
The Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the Montigo fireplace,
there is a ten-year warranty on the firebox and its components, a five-year warranty on the main burner and pilot burner, and a one-year warranty on the gas control
valve, fibre logs and Power Vent Module. The Glass, plated / painted finishes, and refractory lining are exempt from the warranty.
Remedy And Exclusions
The coverage of this Warranty is limited to all components of the Gas Appliance manufactured by The Companies.
This Warranty only covers Montigo Gas Appliances installed in the United States or Canada.
If the components of the Gas Appliance covered by this Warranty are found to be defective within the time frame stated (see The Companies right of investigation
outlined below). The Companies will, at its option, replace or repair defective components of the Gas Appliance manufactured by The Companies at no charge,
and will also pay for reasonable labour costs incurred in replacing or repairing components. If repair or replacement is not commercially practical, The Companies
will, at its option, refund the purchase price of the Montigo Gas Appliance.
This Warranty covers only parts and labour as provided above. In no case shall The Companies be responsible for materials, components, or construction which
are not manufactured or supplied by The Companies, or for the labour necessary to install, repair or remove such materials, components or construction. All
replacement or repair components will be shipped F.O.B. the nearest The Companies factory.
Qualifications To The Warranty
The Gas Appliance Warranty outlined above is further subject to the following qualifications:
(1) The Gas Appliance must be installed in accordance with The Companies installation instructions and local building codes. The Warranty on this Montigo
Gas Appliance covers only the component parts manufactured by The Companies. The use of components manufactured by others with this Montigo Gas
Appliance could create serious safety hazards, may result in the denial of certification by recognized national safety agencies, and could be in violation of
local building codes. This warranty does not cover any damages occurring from the use of any components not manufactured or supplied by The Companies
(2) The Montigo Gas Appliance must be subjected to normal use. The Gas Appliances are designed to burn gas only. Burning conventional fireplace fuels such
as wood, coal or any other solid fuel will cause damage to the Gas Appliance, will produce excessive temperatures and will result in a fire hazard.
Limitations On Liability
It is expressly agreed and understood that The Companies sole obligation, and purchaser's exclusive remedy under this Warranty, under any other warranty,
expressed or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above.
In no event shall The Companies be responsible for any incidental or consequential damages caused by defects in its products, whether such damage occurs
or is discovered before or after replacement or repair, and whether or not such damage is caused by The Companies negligence. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The duration of any implied warranty
with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above may not apply to you.
Investigation Of Claims Against Warranty
The Companies reserves the right to investigate any and all claims against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written Consent
The Companies shall in no event be responsible for any warranty work done without first obtaining The Companies written consent.
Dealers Have No Authority To Alter This Warranty
The Companies employees and dealers have no authority to make any warranties nor to authorize any remedies in addition to or inconsistent with those stated above.
How To Register A Claim Against Warranty
In order for any claim under this Warranty to be valid, The Companies must be notified of the claimed defect in writing or by telephone, as soon as reasonably
possible after the defect is discovered. Claims against this Warranty in writing should include the date of installation, and a description of the defect.
Other Rights
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
NOTE:
The Companies as stated above refer to - Canadian Heating Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp. reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices and also to discontinue colors, styles and products.
Page 18
XG0518 - 140707.2
PVVEX58-300 & PVVEX510-300 External Roof Power Vent
Appendix
Appendix B: State of Massachusetts
Amendment
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as follows:
Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device
that will automatically shut off the gas to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,
including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in
the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon
monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled
equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon
monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days
to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm
shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. (c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions
provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”,
the following requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as follows:
When more than four gas appliances are to be vented through a common gas vent or common horizontal vent manifold, a plan of the proposed vent installation
shall be submitted to the Inspector and the serving gas supplier for review and approval.
Extraction from: Massachusetts Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
XG0518 - 140707.2
Page 19
PVVEX58-300 & PVVEX510-300
Power Vent Termination
Ferndale, Washington
TF: 1.800.789.6236
FX: 1.866.3000.0927
XG0518 - 140707.2
Langley, British Columbia
TF: 1.800.378.3115
FX: 1.604.607.6462
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising